Search Documents

By G. M. T. Marshall

Plans to bring the Geco Mines property in Manitouwadge, Ont., into production began in 1954. At that time over 12 million tons of copper-zinc ore were indicated in a zone 2700 ft long. A concentrating plant was built to handle 3300 tpd of ore and a production shaft was sunk about 1500 ft. MINE LAYOUT Vertical attitude, width, rake, and competent country rock of a 4-million ton orebody west of the main diabase dike suggested a system of blasthole stopes, undercut with scram drifts connected by a transfer raise system to a crusher on the 1250-ft level and this system was employed. A 42-in. conveyor on this level transfers the ore about 1200 ft to a loading pocket at the No. 1 shaft. The system has a number of advantages: 1) Cost of tramming is eliminated. 2) Rate of extraction from any stope is controlled only by the scraping capacity of the scram. 3) Rate of extraction from the stoping area can be very rapid. Fast extraction makes it possible to cut mining costs for the following reasons: The number of stopes actively producing is kept to an economical minimum; the operating area is concentrated-manpower can be used more effectively; and active life of the stoping block is short, making ground support problems simpler and less costly.

Jan 8, 1959

The most extensive oil shale development program ever undertaken in the United States has been that carried out by Colony Development Operation at Para- chute Creek in western Colorado. Field development goals were completed this spring, with the remainder of the $24 million joint venture program, primarily engineering, environmental and economic analysis, due to be finished by the end of 1972. Upon completion of the overall program, a decision concerning a commercial venture is expected. This program points up the increasing attention being focused on oil shale as a source of crude oil and energy for the U.S. at a time when the nation's supply of oil produced by conventional methods is far from adequate to meet the demand. The oil shale reserves of the Green River formation in Colorado, Utah and Wyoming are the largest hydrocarbon reservoir. The Piceance basin of Colorado, alone, contains some 80 billion bbl of shale oil recoverable by modern methods in reserves more than 30 ft thick and containing at least 30 gal of oil per ton. The U.S. Geological Survey has estimated that the total shale oil reserves of the Green River formation in the states of Colorado, Utah and Wyoming is more than 600 billion bbl of oil in deposits containing at least 25 gal per ton of shale oil.

Jan 10, 1972

By W. F. Durfee

The apparatus described in this paper was designed by the writer, in the year 1869, for use in the laboratory of the " American Silver Steel Works," at Bridgeport, Conn., where only the vacuum-pump was erected ; but on two subsequent occasions I have had the combined vacuum-pump and table-blowpipe constructed as represented in the drawings, in which Fig. 1 is a general elevation of the apparatus, the air-chamber being sectioned vertically; Fig. 2, a plan of the air-chamber; Fig. 3, a vertical sectiotnal elevation of the vacuum-pump, the section being on line C L), of Fig. 4, which is a horizontal section on line A B, of Fig. 3. The vacuum-pump is constructed of copper, and consists of a vacuum-chamber, E, supported upon the upper expanded end of a vertical pipe, Q. The vacuum-chamber is provided with four nozzles, C, F, I, D (Fig. 4), two of which are shown in section at A, B (Fig. 3). Passing vertically through the centre of the vacuum-chamber E, is seen the water-supply pipe P, whose lower extremity incloses an internal pipe p, which is supported, and placed in communication with the vacuum-chamber E, by means of the two elliptical nozzles n, n. The upper part of the pipe p is closed by a conical cap, and its lower end is in the same plane with the extremity of the watersupply pipe P, within which it is placed. The relative sizes of the pipes P and p are such that an annular adjutage, one-sixteenth of an inch in thickness, is formed between their lower extremities, through which the water from the supplypipe P passes into the pipe &, drawing any air that may be in the

Jan 1, 1885

By John Cobb

THE attempts of British investigators to arrive at definite knowledge concerning the nature of the nitrogenous constituents of coal have been mainly made through studies of the behavior of coal on carbonization and gasification. There have been carried out numerous determinations of ,the distribution of nitrogen in the products of carbonization under laboratory and large-scale conditions; and by a careful consideration of the extent to which nitrogen is liberated, say as ammonia, at different temperatures and under different conditions of operation as regards atmosphere, it has been possible to form some general notions as to the nature of the nitrogenous compounds present in the coal, and at the same time to arrive at clearer ideas as to what are the important operative factors in determining the ammonia yield under working conditions. This work has been spread over many years and is summarized below. The difficulties of connecting the results in such a way as to allow of the nitrogenous constituents of the coal being described in terms of specific organic structure are great. They arise, for example, in the carbonization process, because the phenomena of decomposition observed at any one temperature can only refer to compounds decomposing at that temperature, each of them with a previous history of chemical transformations occurring at lower temperatures. To put it in another way, the compounds occurring in the coke at any stage are not in the least likely to be those present in the original coal. The same difficulty, in a milder form, occurs when the method of differential solution is attempted. There is always the preliminary question, almost impossible to answer, as to how far the separation by the use of the solvent has involved some form of decomposition of the original compounds. In the following summary, an attempt has been made to bring together results obtained by British workers.

Jan 3, 1925

By R. G. Ward, P. L. Sachdev

Using an improved maximum bubble pressure technique, the densities of iron silicates at 1400°C have been measured under nitrogen. At the wiistite composition the density has been measured by bubble-blowing experments with both argon and nitrogen and calculated from the measured volume of a known mass of melt under nitrogen. The densities under nitrogen are significantly different from those measured under argon for melts containing less than 28 wt pct SiO2. THE constitution of liquid slags is not well understood, largely because no single property or parameter can be measured which gives conclusive evi- dence of the types and packing of the ions present. Of the many property measurements which can provide information leading to a picture of the constitution of slags, density gives the most direct evidence and has been studied extensively. The work reported here is part of a program of study of densities in multicomponent melts in which the iron oxide-silica system is the solvent. These melts are important as they are fundamental to basic steelmaking, and they allow the study of basic silicate compositions which have hitherto been largely neglected. As considerable disparity exists

Jan 1, 1965

By R. D. Springer, R. L. Wilcox, P. A. PALMARTAN, R. K. Waring, E. A. Anderson

A knowledge of the mutual liquid solubility of zinc and lead is of importance in various phases of zinc metallurgy. The determination of this solubility has been the subject of numerous investigations, but unfortunately the results vary widely, particularly at higher temperatures, and it has been impossible to decide what data are most reliable. It was decided to investigate the matter and in view of the disagreement in the published results, it was felt necessary to take rather unusual precautions to insure the reliability of the data. For this reason determinations were made by four different methods, and the procedures of several of the previous investigators were duplicated. The previously used methods can be divided into two classes: methods involving freezing the entire melt and taking samples of the lead-rich and zine-rich phases in the solid state,l,2 and methods in which the samples are taken while the bath is liquid and at the desired temperature.3,4 Data obtained by methods involving freezing the entire melt show much lower solubility of lead in zinc than methods in which the liquid is sampled at temperature. The latter method was used by Spring and Romanoff5 and by Hass and Jellinek.6 The results of these two investigations are in agreement at temperatures near the melting point but at higher temperatures Hass and Jellinek find a higher mutual solubility. The low-temperature section of the zinc-lead equilibrium diagram is given by Peirce and Anderson.7 The diagram is based on the data of Hodge and Heyer,8 Arnemann,9 and Peirce.10

Jan 1, 1934

By Y. C. Liu, W. R. Hibbard

An aluminum single crystal cold-rolled from (110) [1121 essentially retains its initial orientation after 99.6 pct reduction in thickness. The orientation of the recrys-tallized grains of this material can be described in terms of crystallographic rotations about principal poles of deformation texture. DURING the study of the recrystallization of a copper single crystal cold-rolled from a (110) [112] initial orientation, the orientation of the re-crystallized grains could be derived by a 30" rotation of the orientation of the cold-rolled matrix about its <111> poles.&apos; The present investigation was undertaken to extend the work done on copper&apos; to an aluminum crystal also cold-rolled from a (110) [112] initial orientation. Experimental Procedure The procedure of this experiment was similar to that reported for copper.&apos; An aluminum (99.998 pct) single crystal rod* 1 % in. in diameter was grown in back-reflection technique.&apos; The specimen (1.20x 1.004x0.6787 in. thick) was then rolled along the [112] direction. The final thickness was 0.0028 in., giving a reduction in thickness of about 99.6 pet. Specimens were cut from the rolled strip with scissors, and approximately in. of disturbed metal was removed with Tucker&apos;s reagent. The rolling edge remained intact. The specimens were sandwiched between two graphite plates and annealed in a lead or lead alloy bath which was electrically heated. Pole figures were constructed using the techniques previously described.&apos; Specimens were electrolytically polished4 and etched with 47 pct HNO8, 50 pct HC1, and 3 pct of 48 pct HF. The electrolytic polishing method and etching reagent employed for aluminum specimens were not entirely satisfactory and the microstruc-tures could not be studied in any detail. Results and Discussion The octahedral pole figure of cold-rolled aluminum strip is plotted in Fig. 1. The <111> poles spread in the transverse direction approximately 8" for the highest intensity areas. The spread in the transverse direction can be related to a rotation about two <110> directions lying in a plane containing the rolling direction and rolling plane normal. The two <110> directions and a scale of rotation for the <111> poles are shown in Fig. 2. The amount of rotation is consistent for three of the four <111> poles, about 35" to 40". The discrepancy for the fourth pole is believed to be due to limitations of the film technique. Alternate inter-

Jan 1, 1956

By B. D. Cullity

This investigation of bismuth-selenium alloys was made in an attempt to find a suitable material for use in thermoelectric generators. These devices are simply thermocouple circuits designed for the efficient production of electrical energy from thermal energy, which may in turn be derived directly from solar radiation or from the combustion of fuels. The requirements of a material for use in a thermoelectric generator are obviously quite different from those of a material used in a temperature-measuring thermocouple. Naturally, for power generating purposes, the thermoelectric power (voltage produced per degree difference in temperature between the junctions) must be as high as possible. Furthermore, in order to obtain reasonably high power outputs, the materials used in the generator must have an electrical conductivity which is as high as possible. Finally, in order to minimize heat lost by conduction to the cold junction, the thermal conductivity must be as low as possible. The relation between these several factors and the efficiency of conversion of thermal into electrical energy—the thermoelectric efficiency—has been discussed by Telkesl in a recent review of the subject. She gives the thermoelectric efficiency as: W o Efficiency = -Wo ______________i____________ TR-TC+ O2TR-Tc) where W, = power output in external load (watts) Wi = rate of heat input to hot junction (watts) TE,T, = temperature of hot and cold junctions (oA) K1,Kz = thermal conductivity of the two thermocouple materials (watts/cm°C) p,,pz = electrical resistivity of the two thermocouple materials (ohm cm) 9 = thermoelectric power (volts0/C) For many materials, some of the desired properties (for example, high electrical and low thermal conductivity) are almost mutually exclusive; the problem thus becomes one of finding a material which has the optimum combination of pfoperties. Bismuth-selenium Alloys work on the equilibrium diagram of the bismuth-selenium alloys has been reviewed by Hanson who gives the diagram reproduced in There are two intermediate phases in this system, BiSe and Bi²Se3. The existence of an alpha and beta modification of BiSe has not been demonstrated satisfactorily and the writer found no evidence of it in the present work. BiSe and Bi2Se3 have, like bismuth, a rhombohedra1 crystal

Jan 1, 1949

By R. M. Brick, M. A. Williamson

CERTAIN features of the response of copper and brass to deformation and recrystallization remain obscure. The textures obtained on rolled sheet are listed by Schmid and Boas1 as: No adequate explanation has been advanced for the presence of the secondary deformation texture of copper and its absence in brass or for the origin of the cubic recrystallization texture of copper.2 A recent publication3 attempted to rationalize the above empirically described annealing texture of brass on the basis of retention of the (110) [112] rolling orientation plus twinning about the central octahedral poles of the usual secondary (110) [115] orientation. The difference in the textures of annealed copper as compared to 70-30 brass is also shown by the difference in the position of ears for drawn copper, at o° and 90°, as compared with drawn brasses, at 45°, for all compositions between 90-10 and 70-30.4 Data on individual crystals are as yet too few to permit of an analysis of these textures comparable to that of mild steel as made by Barrett and Levenson.5 EXPERITMENTAL METHODS The materials studied included copper specimens cut from the central, equiaxed crystal portion of a tough-pitch wirebar; brass made from this copper and high-purity (99.99 per cent) zinc including alloys of 7 per. cent, 15 per cent, 24 per cent, 29 per cent and 36 per cent Zn and large single crystals of 70-30 brass. Sections ¼ in. thick of the cast polycrystalline copper and brasses were reduced 40 per cent by rolling, recrystallized to a common grain size of 0.045 mm. and then rolled directly to foil 0.002 in. thick. Hardness readings employing both the Vickers and Rockwell machines were taken at intervals during the reduction. For comparison, similar specimens were cross-rolled-i.e., turned through 90 for each pass-and comparable hardness data were secured. Finally sections from the single crystals of brass were cut to obtain the following initial orientations; these sections were rolled, hardness data secured and a complete micrographic record of structural changes obtained:

Jan 1, 1941

By J. M. Davey

Lead-zinc sulphide ores at Mount Isa are currently treated at the rate of 180,000 long tons per 28 day period in the No. 2 Concentrator of Mount Isa Mines Limited. Prior to June 1966 lead-zinc ore was treated in part of the No. 1 Concentrator up to a rate of 70,000 long tons per period. Since 1955, two major changes in ore type being processed have occurred. Because of these changes, problems arising from treatment of the ore have altered and during the period several major changes in practice have been advocated and experimentally tested. Most of these flow sheets were developed with a view to overcoming one major problem in the ore. These were invariably abandoned as the Mount Isa lead-zinc ore contains a number of equally major problems all of which must be overcome in the treatment process. MINERALOGY The orebodies are situated in the Mount Isa Shale Group which is Proterozoic in age (Carpentarian System). The sediments consist dominantly of fine grained dolomitic, quartzo-feldspathic shales and siltstones. Specifically, the Mount Isa orebodies lie in the Urquhart shale formation which is characterised by sediments of high albite and orthoclase content denoting a large volcanic component. The Urquhart shales are approximately 3,500 feet thick and extend at least north and south of Mount Isa for 20 miles in each direction. In the area of the silver-lead-zinc orebodies the Urquhart shales are highly pyritic and have a relatively high carbon content. The

Jan 1, 1970

By Michael Tenenbaum

RECENT researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any sub-stantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed.

Jan 1, 1939

By R. T. Mishler

Silver-gold. mine, in northern Mexico, with arrow veins in rhyolite. One fourth area developed has been ore. Deposits average 20 in. wide and 73 oz. silver per ton; diluted in mining to 40 oz. per ton. Developed by drifts and raises at 100-ft. intervals. Samples cut every 5 ft. Ore and waste sampled separately to make combined stoping width 3 or 3 1/2 ft. Ore reserves figured to sloping width; high assays not modified. Tonnage and assay of ore extracted higher than estimates. Ore stoped principally by cut and fill method. Cars from each stope counted and sampled. Cars check tonnage to concen¬trator within 1 per cent.; silver assay 9 per cent. high. Tonnage and assay from scopes corrected to agree with feed to concentrator. Profit or loss for each slope estimated monthly. THE Lucky-Tiger mine is a silver-gold property, situated at El Tigre, in the northeastern part of Sonora, Mexico, at, an elevation of 6000 ft. in the Sierra Madre Mountains. It is 30 miles by wagon road from the Esqueda station on the Nacozari railroad. Since its discovery in 1903, the mine has produced forty million ounces of silver. The ore has averaged 40 oz. silver and 0.25 oz. gold per ton. Copper, lead and zinc have been of minor importance, having averaged 0.4 per cent., 1.1 per cent., and 1.5 per cent., respectively. The richness of the ore,, combined with its occurrence in narrow veins, required the use of the more expensive methods of mining.

Jan 2, 1925

By William C. Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to temperature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts. INSULATION OF OPEN-HEARTH FURNACES More than ten years ago the writer proposed the insulation of an acid open-hearth furnace system below the charging floor, and it was accomplished, with gratifying results. Possibly that was the first time the insulation of regenerators and slag pockets of any open-hearth furnace was undertaken, but shortly thereafter such insulation became general, and when the six groups of 150-ton furnaces1 were built in 1929-1930, they were completely insulated below the charging floor. While the practice was accepted at least five years ago, it was not well understood, however, as indicated by the following incident which occurred in connection with an installation made in 1929. After the

Jan 1, 1935

By R. Lyndon Arscott, P. Hackett

This chapter reviews the early stages of a study designed to investigate the physical behavior of the coal measure rocks around longwall panels over a relatively large area. The aim of the work is to attempt to explain a directional tendency for a certain type of underground fracture. The geological structure of the area is reasonably uniform but the effect of some local anomalies is also discussed. Although some definite tendencies have been recorded, the results so far achieved need confirmation by further experiments. The chapter deals first with some in-situ strain measurements carried out in longwall panels and continues with a discussion of the relationships between induced fractures and the natural variations in the structure of the rock mass. Finally, some light is shed upon the gas outburst phenomenon although eradication of the hazard is far from assured. STRESS AROUND A LONGWALL PANEL Considerable progress has been made during the last few years towards the determination of the mechanism of failure of small samples of rock under varying environmental conditions. Much more laboratory testing needs to be done in this field but an even greater amount of study needs to be devoted to the extrapolation of laboratory phenomena to failure around underground excavations. The problem is made more difficult because the stress redistribution around an excavation is often difficult to define, particularly when part of the rock mass fails and a

Jan 1, 1972

By William C. Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to temperature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts. INSULATION OF OPEN-HEARTH FURNACES More than ten years ago the writer proposed the insulation of an acid open-hearth furnace system below the charging floor, and it was accomplished, with gratifying results. Possibly that was the first time the insulation of regenerators and slag pockets of any open-hearth furnace was undertaken, but shortly thereafter such insulation became general, and when the six groups of 150-ton furnaces1 were built in 1929-1930, they were completely insulated below the charging floor. While the practice was accepted at least five years ago, it was not well understood, however, as indicated by the following incident which occurred in connection with an installation made in 1929. After the

Jan 1, 1935

By Charles A. Mitke

Excluding top-slicing and sublevel caving, large production caving methods may be divided into two general classes, the branch raise, or undercut caving method, and the combined shrinkage and caving method, each of which has a number of variations, the result of continual efforts towards obtaining lower costs and better extraction, by the introduction and substitution of minor improvements and modifications. Early Caving Methods Present caving methods are the cumulative result of developments covering a period of many years, with the most rapid growth during the past 15 years. They originated, presumably, from early English stoping methods, and, as far as is generally known, were first introduced in the Michigan iron district. They have had their greatest expansion and application in the large low-grade porphyry coppers. In their present form, they are probably a development and combination of sublevel caving and shrinkage (back stoping on ore) with gravity handling of broken material. Sublevel caving, as practiced in the Michigan district today, is a combination of drift, or crosscut, mining, with top-slicing, and caving, supplemented by later refinements in the shape of mechanized handling of broken ore. A height of anywhere from 16 to 20 ft. is generally taken, and the ore is drilled and blasted along the drift or crosscut for half this height (say 8 to 10 ft.), after which the upper 8 to 10 ft. caves and breaks of its own weight, with comparatively little assistance from drilling. This

Jan 1, 1928

By Frederick K. Allgaier

As part of an ongoing research program, the Bureau of Mines, U.S. Department of the Interior, is monitoring surface subsidence over six longwall panels at three Utah coal mines. These sites are characterized by mining depths of 244 to 610 meters (800 to 2,000 ft .), thick and massive sandstone layers in the overburden strata, multiple seam mining, extraction heights of approximately 1.8 to 3 meters (6 to 10 ft.), and rugged surface topography. Maximum subsidence, angle of draw, timing relative to mining, horizontal strain, and rate of subsidence development are being determined and correlated with mining and geologic variables. Results to date indicate the maximum vertical subsidence over the monitored panels ranges from 0.6 to 0.9 meters (2 to 3 ft.). The major factors controlling the amount of subsidence are the panel dimensions and the status of adjacent panel mining. Only minor surface cracking at the panel ends was evident at any of the sites. In all cases, there was a time lag of several months between the start of mining and subsidence at the surface. As subsequent panels are monitored and additional data become available, better estimates of the effect of various site characteristics on the subsidence will be possible. Ultimately, improved prediction capabilities will allow mine operators in the West to evaluate the potential for subsidence-related damage which could affect the current or future land use above the mine.

Jan 1, 1982

By V. Damiano, M. Herman

CELLULAR substructure observed in metal crystals grown from the melt. has been studied extensively&apos;-&apos; and is attributed to the existence of a constitutionally supercooled zone in the liquid ahead of the solidifying interface. The mathematical description of this process has been given in terms of the concentration of solute in the liquid phase, the rate of solidification, and the temperature gradien.t in the liquid as the only variables.5 This technical note presents some evidence of 1) the effect of crystal orientation on some aspects of cellular growth, and 2:) the degeneracy of these cells into dislocation arrays. The zinc single crystals used in these studies were alloyed with cadmium sufficient to produce the constitutional supercooled cellular substructure. Crystals containing 0.05 pct Cd exhibited substructure formation for a growth rate of 10 cm per hr and a temperature gradient of 15°C per cm in accord with the theory. The growing liquid-solid interface was examined after we liquid had been decanted away in a fashion similar to that described by Rutter and Chamers.&apos; The cellular substructure was also observed after polishing and etching the surface directly behind the decanted interface with a solution of HNO, and water. Fig. 1 is a photomicrograph of a typical polished and etched surface revealing substructure, the cleavage plane, and twins. The crystal has been grown with its basal plane parallel to the direction of growth and the plane of the micrograph is per-

Jan 1, 1960

By D. K. Crampton

NEARLY everyone who has not had the benefit of study in the field of metallurgy subscribes to a persistent and enthusiastic belief in the legendary lost art of hardening copper. This of course supplies a perfect introduction to a chapter of information on copper and its alloys, since the dissipation of fallacies and superstitions affecting an art probably constitutes the best method of getting at its real substance. Metals are hardened, but also embrittled, by a plurality of impurities. In the modern technology of copper-base metal products, we are familiar with a great host of materials, passing from one extreme of dead soft copper better than 99.9 pct pure, which in the form of wire about as thick as a match will stand hundreds of full twists in a 12-in. length, to an alloy containing less than 3 pct of alloyed substance possessing the strength of pretty good steel and capable of manufacture into razor blades, should we suddenly be deprived of steel; certainly a much better material for this purpose. Every copper alloy known to primitive man lies in some inter- mediate position and the ancient bronzes that have been found all over the world wherever an early civilization existed are usually contaminated by such impurities as sulfur, oxygen, antimony, arsenic, iron, or other materials, so that they could not possibly conform to any modern intelligent specification insuring the best combination of useful properties in alloys of their type and would go

Jan 1, 1953

By C. R. Van Hise

[Concluding Contribution of Prof. Van Hise to the Discussion of his Paper, and Others on the Same General Subject, presented at the Washington Meeting, February, 1900 (see Ram., xxx., 27, 177, 323, 424, 578) ; also of the contributions of Vogt, De Launay, Beck, Lindgren, Kemp, Rickard, Bain, Keyes, Collins and Adams, presented at the Richmond Meeting, February, 1901, and to be printed in the present volume.] In June, 1900, shortly after my paper was published in the Fransactions, I made a briefer statement* before the Western Society of Engineers covering the same ground, which, in certain respects, is somewhat of an improvement. For instance, instead of using the terms descending and ascending &th reference to the waters resulting in the two concentrations, my modified statement is as follows: " The first concentration of many ore-deposits is the work of a relatively deep water-circulation, while the reconcentration is the result of reactions upon an earlier concentration through the agency of a relatively shallow water-circulation. Commonly the deep water-circulation is lacking in free oxygen, and contains reducing agents, and the shallow water contains free oxygen. The deep water is therefore a reducing, and the shallow water an oxidizing agent."† Of the papers upon ore-deposits which, in vol. xxx. of the Fransactions, follow my own, or which were presented at the Richmond meeting, a considerable number are wholly con-

Jan 1, 1902