Search Documents

By W. C. J. van Rensburg

Exploration of unconventional mineral resources is stimulated by uncertainties about the cost and security of conventional resource sup- plies. Costs of the latter are likely to increase as a result of inflation, higher energy costs declining productivity, a lack of sufficient investment in politically volatile areas, or through cartel-like action. Exploration of unconventional resources is likely to be delayed by these same factors, insufficient research and development facilities, and a decline in capital formation. World economic growth is likely to be slow, so there will be more emphasis on material conservation. Therefore, the incentive to explore for unconventional resources may be reduced.

Jan 1, 1983

By A. Kavetsky, W. J. Whiten

Data from ball mills with a wide range of diameters are analyzed using detailed mathematical/ numerical models. Analysis shows the relative power inefficiency of large ball mills is due to their inefficient breakage of coarse particles. The models developed can be used to scale-up mill behavior. The behavior of large mills at Bougainville and Pinto Valley is compared. It is concluded that the mills are equally inefficient at grinding coarse particles. Differences in coarseness of total mill feed are shown to account for the fact that Pinto Valley mills achieved design throughput whereas Bougainville mills did not.

Jan 1, 1985

By H. W. Peirce

Identified and utilized Arizona salt deposits are of two ages: 1) Permian in the Colorado Plateau, and 2) Tertiary in the Basin and Range country. Uses include: a) storage of energy fluids in man-made solution cavities in both Permian (Supai Formation) and Tertiary (Luke salt body) salt and b) production of marketable products by solution and evaporation of tertiary salt. The two liquid petroleum storage Projects have a combined storage capacity in excess of 380 million L (100 million gal). Current production of salt products approximates 32 kt/a (32,000 stpy). Increasing demand for both storage and salt products is anticipated.

Jan 1, 1983

THE Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and outstanding attainment in the science and practice of iron and steel metallurgy or metallography, chosen by the Board of Directors upon recommendation of the Iron and Steel Division The following were the Howe lectures and lecturers for the years indicated 1924 What is Steel? By Albert Sauveur 1925 Austenite and Austenitic Steels By John A Mathews 1926 Twenty-five Years of Metallography By William Campbell

Jan 1, 1952

By H. V. Fairbanks

Efforts were made to determine the amount of increase in the drying rate which could be obtained through acoustic treatment of ultra fine coal under various conditions, and to test the feasibility of using a rotary kiln and multitiered vibrating screens as a means for continuous drying of coal fines. Introduction of acoustic energy during the rotary kiln experiments increased the drying rates from 10-40%, depending upon the experimental condition. The use of a drying assembly consisting of multitiered vibrating screens produced better results than the rotary kiln and has definite possibilities of providing an effective means of drying coal fines in relatively large quantities.

Jan 1, 1973

By S. Tandanand, Powell. L. R.

The US Bureau of Mines assessed the geological effects on the ratio of maximum subsidence and extraction thickness, known as the subsidence factor, to develop a simple method for predicting the maximum subsidence. The study is restricted to the Northern Appalachian Coal Basin where data were collected from 13 coal mines. A model previously developed to relate the subsidence factor with the lithology and with the width and depth of working panels was used in the assessment. The result shows the possibility of determining maximum subsidence without resorting to a rigorous method.

Jan 1, 1985

By H. F. Yancy

PooR results in coal washing and in ore concentration are sometimes attributed to the shape of the particles in the feed. It is well known that the shape of a particle influences its rate of fall in water. This is evidenced by the value of the constant C in the Rittinger equation for the velocity V of settling in water, V = C-D(d- z ), where C has the following values: 2.73 for roundish grains, 2.37 for long grains and 1.92 for flat grains. This report, which is based upon data obtained during the course of coal-washing investigations conducted by the U. S. Bureau of Mines in cooperation with the College of Mines of the University of Washington, gives the results of a method or procedure of screening in which the particles are separated into three shapes and shows the deportment of these shapes when coal is treated on a coal-washing table. The method consisted in first screening the coal with Tyler standard square-hole sieves, followed by screening tests of each of these products with screens of rectangular opening. For this purpose Tyler "Ton-Cap" screens were used; each square-hole product was subsequently sized with two Ton-Cap sieves so selected that their shortest dimensions were approximately 75 and 50 per cent., respectively, of the opening of the square-mesh sieves. For example: A product which is through 8 mesh (0.093 in.) and on 10 mesh (0.065 in.) is screened on slotted sieves which have openings 75 and 50 per cent. of the 0.065-in. opening in one direction and an opening of not less than 0.065 in. in the other direction. For convenience in discussion, the particles retained on the first slotted screen are termed "cubical"; those retained on the second slotted screen are termed "prismatic" and those passing the second screen are called "flat." (See Fig. 1.) The square-mesh screens separate particles according to two dimensions, length and breadth; the slotted screens divide them further according to the third dimension, or thickness. Prismatic particles have a mass of about two-thirds, and flat particles of about one-half, that of cubical particles of the same square-mesh size. The screen-

Jan 1, 1931

By Alan E. Bland, Jerry G. Rose, Thomas L. Robl

This paper describes the observed variability of the chemical composition of coal preparation plant refuse for the major producing seams of Kentucky. Both the Appalachian Coal Field of eastern Kentucky and the Eastern Interior Coal Field of western Kentucky are represented. Also reported is the variability observed in the chemistry of the coal refuse due to cleaning, and the observed chemical variations between past and present production samples. This represents part of a larger study directed toward characterization and utilization of Kentucky coal refuse.

Jan 1, 1978

By John E. Conley

The slate industry of the United States has shown a marked decline in value of products made annually since the peak year 1925, although there has been moderate improvement over the lean years 1932 to 1934. In 1940, the value of all slate products sold was approximately 5¾ million dollars for a total output of 473,450 short tons. The quantity sold was a little less and the value a great deal lower than the annual averages for the past two decades. Enormous quantities of waste materials result from the quarrying, splitting and milling of slate. Obviously, utilization of such waste material is desirable, not only from the viewpoint of economical operation but also for the purpose of conserving natural resources. One possible use is to produce expanded or puffed lightweight aggregate for use in concretes. Such concretes are strong enough for specific uses, and the advantage of lightness could be obtained in such structures as the walls and roofs of buildings, suspension-bridge roadways and various other applications where weight is a factor. Conceivably, these uses could consume an appreciable annual tonnage. Use of Waste Slates for Making Aggregates The lightweight-aggregate industry has been discussed elsewhere4,5 and need not be covered in detail in this paper. The materials commonly utilized are naturally occurring aggregates such as volcanic cinder, tuff and pumice; by-product materials, such as ordinary cinders and air-cooled slags; and the specially manufactured products, including Haydite, Pottsco, Gravelite, Cel-seal, Superock and Waylite. Slates, however, have not been given the consideration they merit, especially in the United States. In the British Isles, some work has been done3 on certain Welsh slates by the Building Research Station to stimulate the use of these wastes. Requirements for Raw Materials As pointed out by Hughes,4 the lightweight-aggregate industry is segregated in regions adjacent to large cities in order to localize the market and avoid the necessity of long freight haulage. Waste slate from the deposits of eastern Pennsylvania, northern Maryland, and Virginia would meet the basic requirement of ally low-priced structural raw material. One apparent advantage is attained when slate waste, normally discarded, is utilized in the manufacture of a by-product. Mining or quarrying costs usually have been assessed against the main product. Some additional grinding might be desirable, but this operation would be relatively cheap, as most slates grind easily. It is believed that virtually all slates, when properly heated, will expand to some degree. However, types that will expand from 3 to 7 times their original volume are preferred. Fig, I illustratcs the expansion of a Pennsylvania slate. The cube originally

Jan 1, 1942

By Richard J. Gonzalez

The petroleum industry includes varied and extensive operations required to supply increasing quantities of refined petroleum products and natural gas that are essential for the economic progress of an expanding population Petroleum has provided the power for the transformation from the "horse and buggy days" to the age of jets and space exploration, and for the remarkable improvement in productivity per worker in agriculture and manufacturing. Without increasing quantities of oil and gas, the world would face painful readjustments to more expensive forms of energy and lower standards of living Petroleum operations start with exploration, development, and production activities that supply the basic crude oil and natural gas Pipelines, ships, barges, and trucks first transport the raw materials to processing centers and then move the finished products to the ultimate consumers. Processing plants extract liquids from natural gas and refineries convert crude oil into a wide range of products These products include transportation fuels, feedstocks for conversion into numerous products (such as fabrics, rubber, and plastics), light fuels for heating, lubricants, and heavy residual materials (industrial fuel oil, asphalt, and coke) The final activity of wholesale distribution and retail marketing moves products into millions of homes, farms, industrial plants, and motor vehicles The use of coal exceeded that of oil and gas until 1946 in the United States and until 1968 in the rest of the world. However, oil and gas have proved to be such convenient and attractively priced fuels that they now supply three-fourths of the total commercial energy (including coal, hydroelectric, and nuclear power) used in North America and more than one-half in the rest of the world. LARGE SCALE OF OPERATIONS By the beginning of 1970, world crude oil production exceeded 43 million bbl daily, -equivalent to more than 2200 million tpy In addition, natural gas and the liquids recovered from processing natural gas supply about 40% as much energy as crude oil Production of oil and gas provide by far the highest value of all mining operations. In the United States, the value of oil and gas production in 1969 of $13 8 billion exceeded the $13 0 billion value for all other minerals The rate of expansion in use of petroleum has been extremely rapid since World War II World crude oil production doubled from 7,500,000 bbl daily in 1946 to more than 15,000,000 bbl daily by 1955 It doubled again to 30,000,000 by 1965, and will double again by 1975 The use of natural gas has increased greatly in the United States and also in Europe, as important discoveries in the Netherlands and the North Sea and technology for moving liquefied natural gas from Africa provided attractively priced supplies

Jan 1, 1976

By John E. Conley

The slate industry of the United States has shown a marked decline in value of products made annually since the peak year 1925, although there has been moderate improvement over the lean years 1932 to 1934. In 1940, the value of all slate products sold was approximately 5¾ million dollars for a total output of 473,450 short tons. The quantity sold was a little less and the value a great deal lower than the annual averages for the past two decades. Enormous quantities of waste materials result from the quarrying, splitting and milling of slate. Obviously, utilization of such waste material is desirable, not only from the viewpoint of economical operation but also for the purpose of conserving natural resources. One possible use is to produce expanded or puffed lightweight aggregate for use in concretes. Such concretes are strong enough for specific uses, and the advantage of lightness could be obtained in such structures as the walls and roofs of buildings, suspension-bridge roadways and various other applications where weight is a factor. Conceivably, these uses could consume an appreciable annual tonnage. Use of Waste Slates for Making Aggregates The lightweight-aggregate industry has been discussed elsewhere4,5 and need not be covered in detail in this paper. The materials commonly utilized are naturally occurring aggregates such as volcanic cinder, tuff and pumice; by-product materials, such as ordinary cinders and air-cooled slags; and the specially manufactured products, including Haydite, Pottsco, Gravelite, Cel-seal, Superock and Waylite. Slates, however, have not been given the consideration they merit, especially in the United States. In the British Isles, some work has been done3 on certain Welsh slates by the Building Research Station to stimulate the use of these wastes. Requirements for Raw Materials As pointed out by Hughes,4 the lightweight-aggregate industry is segregated in regions adjacent to large cities in order to localize the market and avoid the necessity of long freight haulage. Waste slate from the deposits of eastern Pennsylvania, northern Maryland, and Virginia would meet the basic requirement of ally low-priced structural raw material. One apparent advantage is attained when slate waste, normally discarded, is utilized in the manufacture of a by-product. Mining or quarrying costs usually have been assessed against the main product. Some additional grinding might be desirable, but this operation would be relatively cheap, as most slates grind easily. It is believed that virtually all slates, when properly heated, will expand to some degree. However, types that will expand from 3 to 7 times their original volume are preferred. Fig, I illustratcs the expansion of a Pennsylvania slate. The cube originally

Jan 1, 1942

By James K. Stanley

PREFERRED orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.1 In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurgical literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanical properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important in- formation, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational under- standing of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing 'stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required-it is only necessary punch or machine a disk of the sheet material and insert it into the testing device.

Jan 1, 1943

By Per-Martin Sandgren, Alrik Anttila

LKAB's ores have specific mineralogical properties that make them especially suitable for the production of supergrade concentrates. Conditions are particularly good for this purpose at Malmberget, where a concentrate for high-purity sponge iron production has been produced for many years. This product assays approximately 71.5% Fe and 0.20% SiO2. Potential exists for still further improvement. In recent years, the production of fractioned concentrates has been started. The material lies within the size range 74-125 µm and the approximate chemical analysis is 71.4% Fe and 0.30% SiO2. Other special products are under discussion. Malmberget ores are also suitable for the production of high- purity direct reduction pellets with a SiO2 content below 1%.

Jan 1, 1983

By D. A. Hinckfuss

The large and compact but simple Bougainville Copper Limited flotation circuit has been in operation for 3-1/2 years. Discussion of problem areas encountered since start-up and remedies that have been implemented or proposed, form the main basis of this paper. Full current operational data is also provided.

Jan 1, 1976

By M. T. Erickson, C. A. Rowland

Ball mills 5.5 m (18 ft) in diameter and larger tend to use energy delivered to the mill less efficiently than smaller diameter mills, particularly when the large mills carry 40% by volume ball charges. This paper will explore factors used in scaling up ball mills, showing where the advantages of one factor can possibly be negated by another factor. The paper will propose possible operating limits and areas for further study to establish selection and design limits.

Jan 1, 1985

By S. Ito, Y. Watanabe

In the long range production planning at the Matsumine mine, a management target is to maintain a desired production rate and to keep fluctuations in copper and zinc grades within given allowable limits. A simulation model was developed to find, on a trial and error basis, how feasible and practical the target may be under certain constraints on the underground mining sequence. A number of simulation runs have been made to obtain the most suitable production rate for the long term. In this paper, an outline of the simulation model is described.

Jan 1, 1976

By Gary E. McIntosh

This paper will discuss a US Bureau of Mines project designed to assess and predict the impacts which surface coal mining will have on the regional shallow groundwater system in the Powder River Basin. The primary objective will be met through the accomplishment of the following: (1) The design and establishment of a regional network for monitoring shallow groundwater systems in the basin; (2) monitoring the direction and rate of flow, water quality, and aquifer characteristics of the shallow groundwater systems; and (3) development of a regional groundwater simulation model, with appurtenant subroutines to determine local effects.

Jan 4, 1979

By Harold W. Smith

Ore beneficiation via grinding and flotation has traditionally been considered an art because, until recently, the beneficiation plants that operated effectively were those run by skillful personnel who had acquired an "eye" and a "feel" for the process. Today, thanks to technological developments of the past five to ten years, ore beneficiation can be tackled more scientifically. In properly chosen applications, two developments that can bring significant operational and control improvements to concentrating plants are: • X-ray fluorescent spectrometers-that continuously measure chemical composition of flotation process streams, and • Minicomputers-that are relatively inexpensive and highly reliable in data gathering and process control.

Jan 11, 1974

By William B. Plank

ENGINEERING educators and industries are worried about the engineering manpower shortage that is predicted as a result of the increasing demand for trained engineers not only by industry but by the armed services. This is in the face of a decreasing supply, as is shown by this and other studies. Not only has the number of entering freshmen been decreasing since 1947, because of a decrease in the number of high school graduates entering engineering, but the total number of high school graduates will continue to decrease until 1958 because of the lowered birth rate during the depression years.

Jan 8, 1951

By C. F. Seaman, R. G. Clay

The mines of The Tennessee Copper Co. are in the Ducktown Basin, in southeastern Tennessee. The ore is a heavy sulphide consisting principally of chalcopyrite, pyrite and pyrrhotite and in places running as high as 95 per cent sulphur and iron. Operating mines are the Burra Burra and Eureka. Development ' of the Boyd ore body was started in 1940. Late in 1939 the decision was made to change from fuse and cap to all electric blasting and at the same time electric cap lamps were installed to replace carbide. These changes were made to improve the safety and working conditions in the mines. Both the Bureau of Mines and explosives manufacturers recommended electric blasting as a safety measure. Until that rime, electric blasting had been used only for shaft sinking and in places where it was absolutely essential for safety. Very few men had had experience in this type of blasting, as the places where it was required were those that also required direct supervision. It was necessary for the mining staff to work out methods, procedure, and equipment to be used. In this they were ably assisted by representatives of the explosives manufacturers. Many mistakes were made and it is the purpose of this paper to describe the original plan and installation, show the major difficulties encountered. the remedies applied, and present the practices now being followed. Comparison of costs of the two methods will also be discussed. About six months were required to make the change and eliminate fuse and cap blasting entirely. The first electric blasting stations were installed in November 1939 and the last fuse was taken underground in May 1940. A very unusual condition forced the use of fuse for a short time in one heading after May, but that will be discussed later. Original Equipment and Installation A power line is generally recommended as a source of current where permanent blasting stations are used. The plan worked out for electric blasting was to tap 220-volt alternating-current lines when they were available and use 250-volt direct current from the trolley wire at all other places. A blasting machine would be available at each shaft for places where there were no regular blasting stations and could be used if a regular station should fail. The equipment decided on was No. 16 duplex reinforced lamp cord for lines to within about 50 ft. of the working place and No. 20 lead wire from that point to the shots. An open double-pole, double-throw switch with slate base was put in the circuit, so connected that the down position would close the line to the shots 2nd the up position would connect it to the Iine from the power contactor. This switch was located in the circuit as close to the blast as was safe (should the shots explode when it was placed in the shooting

Jan 1, 1943