Search Documents

By G. Richard Dreese, Harold L. Bryant

The coal mining industry has had a long history of successfully externalizing part of its costs. Thus the private or internal costs of coal mining have been minimized and the social or external costs have been ignored. The externalized costs have largely taken the form of water pollution from acid mine drainage and sedimentation of stream channels from eroding spoil banks and gob piles. The environmental problems created by strip mining are very conspicuous, so the public demand for legisla-

Jan 1, 1975

By R. L. Featherly, J. R. James

The replacement or reconditioning of oil storage tank bottoms due to external corrosion is an expensive maintenance item to the oil industry. Cathodic protection as a means of mitigating this problem has proved very successful in the past few years. One pipe-line company recently used magnesium anodes to cathodically protect two 55,000 bbl and two 20,000 bbl tanks. The tank bottoms were protected as individual units with considerable factual data being taken on one of the 20,000 bbl tanks. Twelve 60-lb anodes were installed about 2½ ft from the tank on approximately 17-½ft centers around the tank. Previous installations and tests have shown that sufficient protection is provided when the tank-to-soil potential using a copper-copper sulphate half-cell as a reference electrode is — 0.90 volts at the edge of tank. Potential measurements taken a few months after completing the installation indicated that the potentials were higher than were needed for protection. Resistors were then inserted in the individual anode circuits which increased the life of the anode installation and still provided adequate protection for the structure. All connecting pipe lines were then insulated from the tank. This limited the anode current strictly to the tank resulting in a greater degree of protection with a still longer anticipated anode installation life. The total installation cost for this tank was less than $300 which amounts to $20 per year The corrosion of metallic structures in contact with soil or water has been a very serious and costly problem for centuries. The annual loss to our nation's pipelines alone is estimated at $200,000,000. Mitigation of this problem by various methods has been carried on quite successfully for a number of years. An electrical method called cathodic protection has been used with considerable success to control corrosive influences on pipelines, tank bottoms, cable sheathing and other buried metal structures. Corrosion of oil storage tank bottoms has been a serious problem among the oil industries for years. In addition to damage costs and loss of oil, the replacement of one tank alone represents several thousand dollars. A reconditioning program at periodic intervals was instituted by several organizations and found to be a very expensive process. A few years ago two of the pipeline companies installed cathodic protection units at their tank farms.3'4 The average current required for protection of the tank bottoms varied from 0.7 to 1.0 milliampere per square foot. The results indicated that adequate protection was obtained at a cost of approximately 10 pct of the previous reconditioning program. The Republic Pipe Line Company experienced severe corrosion on their oil storage tanks. One of their 55,000-bbl tanks

Jan 1, 1948

By R. L. Featherly, J. R. James

The replacement or reconditioning of oil storage tank bottoms due to external corrosion is an expensive maintenance item to the oil industry. Cathodic protection as a means of mitigating this problem has proved very successful in the past few years. One pipe-line company recently used magnesium anodes to cathodically protect two 55,000 bbl and two 20,000 bbl tanks. The tank bottoms were protected as individual units with considerable factual data being taken on one of the 20,000 bbl tanks. Twelve 60-lb anodes were installed about 2½ ft from the tank on approximately 17-½ft centers around the tank. Previous installations and tests have shown that sufficient protection is provided when the tank-to-soil potential using a copper-copper sulphate half-cell as a reference electrode is — 0.90 volts at the edge of tank. Potential measurements taken a few months after completing the installation indicated that the potentials were higher than were needed for protection. Resistors were then inserted in the individual anode circuits which increased the life of the anode installation and still provided adequate protection for the structure. All connecting pipe lines were then insulated from the tank. This limited the anode current strictly to the tank resulting in a greater degree of protection with a still longer anticipated anode installation life. The total installation cost for this tank was less than $300 which amounts to $20 per year The corrosion of metallic structures in contact with soil or water has been a very serious and costly problem for centuries. The annual loss to our nation's pipelines alone is estimated at $200,000,000. Mitigation of this problem by various methods has been carried on quite successfully for a number of years. An electrical method called cathodic protection has been used with considerable success to control corrosive influences on pipelines, tank bottoms, cable sheathing and other buried metal structures. Corrosion of oil storage tank bottoms has been a serious problem among the oil industries for years. In addition to damage costs and loss of oil, the replacement of one tank alone represents several thousand dollars. A reconditioning program at periodic intervals was instituted by several organizations and found to be a very expensive process. A few years ago two of the pipeline companies installed cathodic protection units at their tank farms.3'4 The average current required for protection of the tank bottoms varied from 0.7 to 1.0 milliampere per square foot. The results indicated that adequate protection was obtained at a cost of approximately 10 pct of the previous reconditioning program. The Republic Pipe Line Company experienced severe corrosion on their oil storage tanks. One of their 55,000-bbl tanks

Jan 1, 1948

By D. M. Bondurant

Auger mining-extraction of coal with large diameter augers is proving profitable in recovering coal left after stripping has ceased to be economical. Its many advantages-low initial cost of equipment, low operating cost, low power demand, adaptability to selective mining, simplicity of operation, etc.-have excited the interest of some in the industry in its possibilities for underground operation.

Jan 5, 1951

By M. Katzer, R. Klimpel, J. Sewell

The effect of using selective dispersants as wet grinding aids for ores is demonstrated on laboratory scale batch and continuous grinding equipment. A complete characterization of behavior is performed on a given ore to demonstrate correlations involving torque, % solids, net production rate, and slurry weight and volume loading. The relationship between such laboratory data and industrial scale testing results is very consistent.

Jan 1, 1982

By Alfred Weiss

Approximately 850 delegates from 24 countries met in Tokyo, Japan, May 24-27, for the second MMIJ-AIME Joint Meeting in 55 years, to exchange technical knowledge and experience in the fields of exploration, mining, metallurgy and petroleum engineering. The first such meeting was held in 1917 in Kyoto, Japan. Although the Mining and Metallurgical Institute of Japan was the sponsor, the entire meeting (machinery exposition, technical program, and tours) was a joint effort of the two institutes.

Jan 7, 1972

The Institute is custodian of funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given below. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers.

Jan 1, 1929

By Harry H. Power

While the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a Preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, Personality and health. The engineer's lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the Product is found wanting, the one most responsible should For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Manyof them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of non-college grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more inter. ested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more emphasis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been ,de of the beneficial results to be obtdned by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941

By Howard C. Dunkle

Various factors can affect the quality of BIII2 and BIII3 steel as produced in a bessemer plant; among them: vessel-charging practice, blowing practice, ingot-pouring practice, ingot delivery-time practice, pit-heating practices, and ingot-rolling practice. Evaluation of the influence of ingot delivery time on quality has been chosen as the subject for this paper because this time is completely within the control of the operator, and on this particular factor there is a tremendous amount of information in the dusty archives of the average steel plant. In order to know how much improvement can be made and when attention should be directed to other factors that influence quality, in the continual struggle for improvement, the effect of ingot delivery time must be accurately evaluated. Once this is done, the importance of other variables can be accurately obtained, thus eliminating the necessity of resorting to opinions that are of doubtful value at best. In the study described herein, extensive use was made of the statistical card system as a method of determining the effect of ingot delivery time as a quality factor in bessemer screw-stock grades by simple direct correlation. The value of this statistical method as a means of accurately determining the influence of various factors has been amply demonstrated by Work1 for the bessemer process and by Hand and Gould2 and Fetters and Chipman3 for the open-hearth process. The quality records of 300,000 tons of bessemer screw-stock billets were used in this study of the effect of ingot delivery time on the rejections for breaks, pipe, check and seams. The reduction in the number of rejections for poor quality reduces the costs and increases the productivity per man-hour. The operator today, more than ever before, must know how to keep costs down, how to do it most quickly and in the best way, and how to obtain the highest quality in line with the ever increasing demands of the customer. It is necessary for him to know the individual relations and interrelations between various factors affecting the quality of the manufactured product if he is to produce material that will meet competitively the cost, performance, and quality demands of the trade. Significance of Steel Manganese, Mixer Silicon and Steel Sulphur as Quality Factors In order to obtain the highest grade of material it is necessary to control many factors—not just one or two, as operators

Jan 1, 1945

By T. D. Guldem, J. L. Kaae

ALLOYS with nominal composition of 45-Fe 35-Ni 20-Cr, ASTM-B-163, known under the commercial names of Incoloy 800 and Sanicro 31 (Alloy 800), are often employed at elevated temperatures for extended periods. Therefore, knowledge of the aging behavior of these alloys is of considerable importance. Significant decreases in ductility and increases in yield strength have been observed in the 45-Fe 35-Ni 20-Cr alloys containing about 0.4 pct Ti and 0.4 pct A1 after long-term aging at 540" to 700"~."~ However, no direct evidence has been presented for precipitation phenomena that might result in such changes. Strengthening effects have been attributed to the effects of local or-dering.3 Since y' precipitation (Ni3A1, Ti) is known to occur in similar alloys which contain more titanium and aluminum,4-7 it was decided to explore the possibility that y' might precipitate in these alloys and might be responsible for the changes in mechanical properties on aging. This note reports some observations of two distict types of matrix precipitates made by means of transmission electron microscopy, in a 45-Fe 35-Ni 20-Cr alloy containing 0.31 pct Ti and 0.4 pct Al. The steel used in this investigation was obtained from the Sand-vik Steel Works; it is designated Sanicro-31 (Alloy 800). The chemical composition of the alloy is given in Table I. Aging of solution-treated material at 700" and 800°C for 130 and 100 hr, respectively, produced the matrix precipitates shown in Figs. l(a) and l(b). It is apparent from these micrographs that the precipitate particles occurred in the form of thin square plates parallel to the matrix cube planes. Extraction replication and selected-area electron diffraction showed that the precipitates were M23C6. Coherency strains, consistent with the semicoherent nature of small M23C6 precipitates,' were evident for certain imaging conditions. In addition to matrix precipitation, preferential precipitation of M23C6 on dislocations was common, as has been reported previously for austenitic stainless steels.'" Specimens aged for longer times (-300 hr) at 700°C exhibited a different type of coherent matrix precipitate in addition to the M23C6. An example is shown in Figs. 2(a) and 2(b). In addition to the few large M23C6 precipitates, small precipitates exhibiting strain contrastl0,ll are present. The "line of no contrast" of the strain field of a given precipitate lies along differ-

Jan 1, 1970

By Harry H. Power

While the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a Preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, Personality and health. The engineer's lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the Product is found wanting, the one most responsible should For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Manyof them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of non-college grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more inter. ested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more emphasis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been ,de of the beneficial results to be obtdned by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941

By D. W. Gentry, H. E. Sherer

Determining the age at which to replace a specific piece of mining equipment, and choice of the best possible replacement, is a problem common to nearly all mining operations. This paper examines the data required for intelligent equipment replacement decisions and discusses how to predict future repair cost from historic data, determine the total cost of various replacement alternatives, and evaluate the different replacement alternatives. Various operations research and computer methods were used to develop this easily-used, practical equipment replacement method.

Jan 1, 1984

By Will Mitchell, T. G. Kirkland, C. L. Sollenberger

The beneficiation of a scheelite ore by flotation was investigated with emphasis on determining optimum conditions for obtaining maximum grade and recovery in the rougher concentrates. Variables such as pH, time, temperature, and pulp density during conditioning were plotted against the grade and recovery of the rougher concentrates. Several gangue regulators were tried, and several methods of cleaning rougher concentrates are described.

Jan 1, 1951

By E. N. Pennebaker

The concept of "unitization" comes from the petroleum industry. Of this, Campbell says: "Unitization is the process whereby the owners of adjoining properties pool their reserves and form a single unit for the operation of the properties. The revenue from operation of this unit is then divided in accordance with the basis established in the unit agreement. "The purpose of such an agreement is to produce the reserves more efficiently and thus to increase the profit to every participant."'

Jan 8, 1973

By W. C. Krumbein

GEOLOGICAL problems are approached from a geometrical (space relations) viewpoint, a kinematical (time sequence) viewpoint, or a dynamical viewpoint. The first two require sound training in conventional geology and in field methods. The third approach requires a solid foundation of chemistry, physics, and mathematics. Modern training for geologists should include close integration of basic sciences with geological principles.

Jan 1, 1941

By J. Boldy

Discovery of the Delbridge massive sulfide deposit in the Noranda district of Quebec resulted from an appreciation of the significance of a mercury leakage halo as a lithochemical pathfinder to blind ore. Its location, relative to a geologically inferred ore-bearing horizon within complex volcanic stratigraphy was also a factor. Systematic sampling of microfractures present in outcrops delineated a diagnostic anomaly, drawing attention to an area considered prospective for buried ore. The massive sulfide deposit was subsequently found to be blind and topped at the 110-m (360-ft) level.

Jan 1, 1985

By I. Iwasaki, R. Titi-Manyaka

Chlorination and chloridization behaviors of pyrite, pyrrhotite, marcasite, chalcocite, covellite, galena, sphalerite, heazlewoodite, and elemental sulfur were investigated by thermogravimetric analysis. The possible reaction mechanisms are discussed on the basis of the theoretical weight changes and thermodynamic considerations. Chlorine is a more effective chloridizing agent than hydrogen chloride. In the light of the experimental results, a scheme for producing nonferrous metal chlorides, molten sulfur, and ferric oxide from complex sulfide flotation concentrates is discussed.

Jan 1, 1974

By H. N. Herrick

The flow characteristics of drilling muds, as described in this paper, and the method given for solving problems relating to the flow of these muds through pipe and accessory equipment, are based on a conception that drilling muds are plastic solids like paints or greases; not liquids. The data presented in this report have been obtained from studies of California muds, chiefly those used in the Kettleman Hills field, by the Producing Department of the Standard Oil Company of California. Although no claim of scientific exactness is made for the formulas and diagrams, since the data upon which they are based are not complete even for California muds, the method has proved to be a convenient means for estimating, closely enough for practical purposes, the pressures required to force muds at various rates through pipe systems in which-they are handled. Certain approximations have been made to simplify the procedures so that they can be used easily in the field. Viscosity and Shearing Strength of Mud For the purpose of this discussion a plastic solid is defined as a material in which no deformation or flow takes place when the material is subjected to shearing forces, until the shearing force reaches a value called the "yield point." With liquids, the smallest force will produce continuous deformation; that is, the yield point of liquids is zero. The difference between true liquids and muds is illustrated in Fig. 1, which shows rates of flow through a small tube under different pressures. The flow rate of the liquids is directly proportional to the pressure and that of the muds is not. The behavior of drilling mud does not conform in every detail with the definition of a plastic solid as given, because mud actually flows slightly at pressures below its yield point. However, for practical purposes the definition describes the condition adequately and has the advantage of simplicity. In order to make mud-flow calculations based on the theory that mud is a plastic solid, it is necessary to know the "yield point" of the mud, which hereinafter is defined by equation 1 under the caption "Viscosity

Jan 1, 1932

By Henry E. Colton

Very little information has been published concerning the Tennessee coal-field. The State never appropriated over $600 per annum for a geological survey, and that was discontinued about 1870. Yet even with that small sum Dr. J. M. Safford made a

Jan 1, 1886

By C. V. Millikan

Temperature measurement in wells is an old practice and geothermal gradients have been of interest to geologists for many years.le2 Their application to the operation of oil wells is a more recent practice. It has long been recognized that temperature anomalies occur in drilling and producing wells but thermometers that could obtain a satisfactory record of the anomalies were not available. The normal geothermal gradient is con-sidered as being about one degree Fahren-heit for each 60 ft. of depth.4 This "nor-mal " gradient varies in different areas, but whatever it may be in an area there is little variation from the surface to as deep as the : drill penetrates. The normal gradient is appreciably changed by gas expanding ; from the reservoir into the borehole or by the movement of fluid through a borehole : while drilling, producing, or circulating. It is the resulting anomalies and abnormal gradients from which conditions in wells can be interpreted. Some of the applications of such interpretations are locating the position of oil or gas sands, permeable strata in a reservoir zone, gas-oil contact, source of water, casing leaks, and the top of cement behind casing. Thermometers A thermometer for use in wells must be sensitive and have a low thermal lag. The sensitivity should permit recording 0.2OF. or less for differential temperatures although the actual temperature need not be more accurate than 1°F. The thermal lag should be as low as rugged construction will permit in order to allow surveys to be made in a minimum of time. Of the several kinds of thermometers, these requirements are most easily obtained with the vapor-pressure, expansion, and electric-resistance types. Thermometers for use in wells may be self-contained—that is, the complete instrument is lowered into the well and a record made of the temperature—or the thermal element only may be lowered into the well and the temperature recorded at the surface. The vapor-pressure and expansion types are more adaptable for a self-contained instrument while the electric-resistance thermometer is more suitable for surface recording of temperatures. The self-contained instrument can be run against high pressure on a single wire line with only one operator required. The instrument and its hoisting equipment is easily portable and can be mounted on a small car. The disadvantages are a somewhat greater thermal lag and the necessity of completing a run before any temperature or temperature anomaly is known. A surface-recording thermometer has the advantage of being somewhat more sensitive and of having a lower thermal lag. The Operator can see what anomalies are encountered and can immediately change the running conditions of the instrument or the well conditions in order to obtain the most

Jan 1, 1941