Search Documents

By L. D. Jaffe

From the limited experimental data in the literature, preliminary values were derived for the thermal diffusivity of titanium alloys and for the quenching severity of various mediums used in heat treating them. The thermal diffusivity, under quenching conditions, was found to be approximately 0.006 sq in. per sec. The quenching severity H for brine is approximately 8, for water 4, for oil 0.9, for air 0.08, and for argon 0.02 in. -' The quenching severity of the Jominy-Boegehold end quench water jet against titanium alloys appeared effectively infinite. Using these results, graphs were prepared showing ideal round sizes and Jominy positions having cooled conditions equivalent to those at the center and surface of titanium alloy rounds, plates, and sheets quenched in various media. THE importance of proper quenching of steel parts has long been recognized, and much quantitative work has been done on the subject. Recently, it has become evident that for titanium alloys, too, the rate of cooling from high temperature is important in obtaining high strength and hardness. Maximum hardness and strength may not be attained in the as-quenched condition but rather after a subsequent tempering or aging treatment. Nevertheless, if cooling from temperatures near the ß transus is too slow, for the hardenability of the alloy used, a soft a-ß structure will be produced which will not harden on subsequent aging.'-" The quenching of parts of practical interest can usually be approximated by simple shapes, such as cylinders (rounds) and plates (or sheets) of various thickness and combinations of these. A standard that has been used extensively for comparison purposes is the center of an ideal round: a cylinder quenched in a medium that instantly cools its surface to room temperature." For steel, considerable practical use has been made of the Jominy-Boegehold end quench hardenability specimen,".' and its value for titanium alloys is becoming evident. It therefore appeared worthwhile to attempt comparison of cooling conditions in titanium alloy rounds and plates of various sizes quenched in various media with cooling conditions in ideal round and Jominy quenches. These comparisons are based upon measurements reported in the literature. Quenching Severity of Jominy Water Jet and of Brine As one starting point, there were available the data of Phillips and Tobin8 for positions on a Jominy specimen having the same hardness as the centers of round bars of various size quenched in 5 pct NaOH brine, shown in Table I. The Jominy speci- men is a round bar, normally 1 in. diam and 4 in. long, quenched by a water jet at one end and air cooled on the other surfaces.' After quenching, hardness is measured vs distance from the quenched end on longitudinal flats ground 0.015 to 0.10 in. deep. The data of Table I were based on a subsized specimen of 3/4 in. diam. Since the positions tested are close to the jet quenched end, cooling there may be taken as due solely to the jet, and air cooling can be neglected. These positions are then equivalent to various locations near one surface of an 8 in. plate jet quenched on both sides. Assuming that the thermal diffusivity is constant and that Newton's law of cooling holds, temperature vs time curves at corresponding positions in Jominy specimen and round bar then may be calculated for various assumed quenching severities of the water jet and of the brine. Cooling curves are generally taken to be metallurgically equivalent when they show the same time to reach a temperature halfway between the initial (heat treating) temperature and the final (quenching medium) temperature.5 On this basis, using Russell's tables,9 upplemented by heat flow tables derived in similar fashion by the author for positions near the surface of severely quenched plates, it was found that the experimentally observed equivalence, Table I, was best matched if the quenching severity H of the Jominy water jet was taken as infinite (H = co). This means that the jet quenched surface should be considered as instantly cooled to the temperature of the water

Jan 1, 1956

Future of State and Federal Oil Regulation. BY NORTHCUTT ELY (Trans , vol 118 2400 words) The Interstate Oil Compact, ratified by six states and Congress in 1935, replaced the petroleum code, invalidated with other codes by the Schechter decision This compact endeavors, first, to conserve reservoir energy of oil pools through substantially uniform conservation measures by the states, second, it recognizes the state rather than the Federal Government as possessing the necessary police power for that purpose, third, it establishes an interstate advisory commission, so that orderly production in one state is not penalized by uncontrolled production in another, fourth, Federal interests are recognized in the control of hot oil, regulation of imports and fact-finding forecasts of supply and demand by the Bureau of Mmes It is not as complete an instrument as proposed by the Federal Oil Conservation Board in 1932, but is workable, and will be effective in proportion to the support given it by the industry Three results may follow First, now that fear of Federal control has subsided, the industry may lose interest in the compact and let it fall to pieces, second, if vigorously supported by the industry, the compact can accomplish most of the conservation objectives sought by the Federal control measures now believed unconstitutional, third, if the Compact fails, Federal regulation is almost certain to be revived, and can probably be sustained in connection with neutrality legislation, regulation of interstate pipe lines, and coordination of Federal and state gasoline taxes Nearly every step toward governmental regulation has originated within the industry state proration, the Federal petroleum code, Federal control of imports, Federal control of hot oil are examples The Compact shows a trend toward coordination between the powers of the industry, the state government, and the Federal Government If this arrangement fails through lack of interest by the oil industry, the next step is likely to be absorption by the Federal Government of the other two factors involved in the situation

Jan 1, 1937

By C. A. Heiland

GEOPHYSICAL methods are playing an ever increasing part in various engineering fields. About ten years ago, geophysical exploration was first applied in civil engineering to the study of foundations and the location of construction materials and water. Its usefulness is now being extended into the field of structural engineering. Almost every structure has to be so designed that it will withstand any force to which it may be subjected. Such forces may result from its own weight, applied loads, pressures of various kinds, including those due to wind and water, ground subsidence and vibrations. The last two, problems involving the nature and dynamic behavior of surface and subsurface formations, are within the scope of geophysical investigations. In the design of any structure, the disposition and dimensions of its members as well as their materials must be so selected that they will withstand any or all of the forces enumerated above. In other words, its "resistance" to such forces must be sufficient, allowing for a definite margin of safety. Often a static treatment of the problem leads to satis-factory results, but the static method entails serious errors when vibra-tions are involved, as in resonance with an impressed vibration the displacements of a structure or parts thereof may dangerously exceed the allowable values. The principle of "dynamic design"? is, therefore, avoiding or reducing resonance by suitable selection of the natural frequency of a structure, or by the provision of damping.

Jan 1, 1939

By T. R. Armstrong

During the year 1939, Mexican production totaled 42,479,000 bbl.; a daily average of 116,381 bbl. or a little over 2 per cent of the estimated world production. The Mexican Government operates 100 per cent of the refining branch of the industry, 100 per cent of the domestic distribution, 96 per cent of the crude production and 92 per cent of the total exports. No discussion of the Mexican petroleum industry in 1939 is adequate without reference to the "expropriation" of the foreign-owned oil properties in Mexico by executive fiat on March 18, 1938. The forcible seizing of the properties culminated a long series of efforts on the part of the Mexican Government to obtain control of the oil properties developed through foreign initiative and with foreign capital in Mexico. The heart of the issue is whether the Mexican nation or any nation may with impunity confiscate the legally acquired properties of American citizens. The Department of State of our Government has in its communications to Mexico emphasized the fact that its "expropriation" of American properties was confiscatory because Mexico had failed to make "adequate, effective and prompt compensation"; that the taking was no less confiscatory "because there may be an expressed intent to pay at some time in the future," and that, consequently, "Mexico has assumed and continues to assume to exercise a right without compliance with the condition necessary to give such exercise a recognizable status of legality." Mexico has professed its willingness to pay for the oil properties but at the same time through its Supreme Court it has declared that the owners or lessees do not have the exclusive right to extract and dispose of the oil in the subsoil. This is a reversal of the Mexican position with respect to oil as set forth in the Mexican mining laws, affirmed by Mexican Supreme Court decisions, and as clarified in the Warren-Paync and the Morrow-Calles agreements, as well as in diplomatic correspondence. Efforts to Settle the Controversy Responding to suggestions from the State Department, representatives of the principal oil companies undertook in 1939 to effect a direct

Jan 1, 1940

By T. R. Armstrong

During the year 1939, Mexican production totaled 42,479,000 bbl.; a daily average of 116,381 bbl. or a little over 2 per cent of the estimated world production. The Mexican Government operates 100 per cent of the refining branch of the industry, 100 per cent of the domestic distribution, 96 per cent of the crude production and 92 per cent of the total exports. No discussion of the Mexican petroleum industry in 1939 is adequate without reference to the "expropriation" of the foreign-owned oil properties in Mexico by executive fiat on March 18, 1938. The forcible seizing of the properties culminated a long series of efforts on the part of the Mexican Government to obtain control of the oil properties developed through foreign initiative and with foreign capital in Mexico. The heart of the issue is whether the Mexican nation or any nation may with impunity confiscate the legally acquired properties of American citizens. The Department of State of our Government has in its communications to Mexico emphasized the fact that its "expropriation" of American properties was confiscatory because Mexico had failed to make "adequate, effective and prompt compensation"; that the taking was no less confiscatory "because there may be an expressed intent to pay at some time in the future," and that, consequently, "Mexico has assumed and continues to assume to exercise a right without compliance with the condition necessary to give such exercise a recognizable status of legality." Mexico has professed its willingness to pay for the oil properties but at the same time through its Supreme Court it has declared that the owners or lessees do not have the exclusive right to extract and dispose of the oil in the subsoil. This is a reversal of the Mexican position with respect to oil as set forth in the Mexican mining laws, affirmed by Mexican Supreme Court decisions, and as clarified in the Warren-Paync and the Morrow-Calles agreements, as well as in diplomatic correspondence. Efforts to Settle the Controversy Responding to suggestions from the State Department, representatives of the principal oil companies undertook in 1939 to effect a direct

Jan 1, 1940

By C. V. Millikan, C. V. Sidwell

There is nothing more important in petroleum engineering than a definite knowledge of the pressure at the bottom of an oil well at any existing operating condition, and the relation of this pressure to the pressure within the producing formation. A knowledge of bottom-hole pressures is fundamental in determining the most efficient methods of recovery and the most efficient lifting procedure, yet there is less information about these pressures than about any other part of the general problem of producing oil. Determination of Bottom-hole Pressures Bottom-hole pressure may be calculated or determined by several methods. On an inactive well it may be calculated from the fluid head or, if the well is shut in, by adding the casinghead pressure, the static head of the gas and the fluid head. In wells flowing naturally through tubing the pressure at the bottom of the tubing may be calculated by adding the pressure at the casinghead between the tubing and the casing and the pressure due to the weight of the column of gas, but there is always possibility of error caused by fluid being in the annular space above the bottom of the tubing. If a well with tubing is flowing through either the annular space or the tubing, sufficient gas may be injected through the static space to insure that it is free of fluid but not sufficient to establish an appreciable friction loss. The pressure at the bottom of the tubing can then be calculated by adding to the pressure at the tubing head the pressure due to the weight of the column of gas. This is probably the most accurate method of calculating bottom-hole pressures. In wells flowing by gas-lift, the pressure at the point the gas enters the flow may be calculated by a gas-flow formula. Several types of pressure bombs have been used to measure the pressure at the bottom of wells. One is a piece of steel tubing with a check valve in the bottom and a connection for a pressure gage at the top. It is lowered into the well to the point at which the pressure is

Jan 1, 1931

By J. M. Morris

THE point to be made most clear in this paper is the economic value of flotation in the Benguet mill flow sheet. It is rather a statement of effect with no attempt at a technical explanation of the cause. Certain well-known, easily understood reagents, mechanisms and principles have been adapted to the conditions at Benguet, and have proved to be more successful than was demonstrated in the laboratory. The mechanical and metallurgical development of this particular operation was arrived at by trial and error, with fortunately very little error. Changes were slow, of necessity, which in the end proved a blessing in that time was afforded for observation and analysis of the disturbing factors; and as a result each change was a definite step towards higher efficiency. Many of these steps were unpredictable from labora-tory work because of the varied and differing characteristics of ores met with in daily operation of the mill, which were practically impossible to reproduce on a laboratory scale. The Benguet mill receives daily ores that differ as much as if they were delivered from three different properties. There is first the surface and upper-level zone, which produces an oxidized secondary ore contain-ing considerable iron oxide, manganese oxide and some organic matter. Formerly, most of this ore consisted of very soft fill with some hard rock mixed in. It also contained an unusual amount of iron and aluminum sulfate, which formed hydrates upon entering the alkaline cyanide solu-tion and caused excessive frothing. When flotation was introduced in the Benguet mill the general char-acteristics of this upper-level ore had changed considerably, in that it was practically all newly mined, fairly hard ore. It still contained many of the same disturbing elements, but was somewhat simpler to treat than formerly. The small proportion of fines is still troublesome in flotation, and plant practice probably does not show more than 80 per cent extraction on this small portion of the ore. No definite figure on this is available, as this particular ore is delivered at irregular intervals

Jan 1, 1936

By M. Friedman

Applications of rock mechanics to the design of engineering structures in rock involve the assumption that the stresses are due entirely to the present applied loads. For instance, it is assumed that the vertical normal stress in undisturbed rock free of topographic effects is equal to the weight per unit area of the overburden. In fact, vertical dilatational strains associated with stresses of more than 100 times the present overburden pressure have been measured by strain-relief methods on outcrops. 1,2 The notion of residual strain (stress) or latent stress3 seems unassailable; and indeed this has long been recognized by metallurgists. It is difficult, however, to assess the residual component of the in-situ state of elastic strain with conventional strain relief methods employed in mines or down boreholes. That is, in principle, the in-situ state results from the superposition of present applied loads (natural or man- induced) and potentially recoverable elastic strains (stresses) that exist in a given volume of material even though there are no external forces across the boundaries of the body (Voight,4 and Fig, 1). Accordingly, only in unloaded blocks can the true residual strains be measured by strain relief methods. Using X-rays, the elastic strains locked within the quartz grains or crystals of a rock can be measured. These strains are known to persist even when the rock is reduced to small chips but to vanish when the rock is disaggregated and the grains are powdered. Although we have just begun to investigate the mechanisms by which the strains are stored (see Preliminary Results), we believe that "pressure solution'' at grain boundaries, secondary cementation under load, permanent ("plastic") deformation, and temperature changes are possible processes. In any event, in our study of naturally deformed rocks, it is significant that we are work-

Jan 1, 1972

By V. J. Berry, J. D. Pendergrass

Well pressure transient tests provide a means for directly obtaining information about formation pressure and reservoir flow capacity. Such tests have also been proposed for determining presence and location of faults or other reservoir closures and for measuring oil in place. For mathematical convenience, most theoretical studies have considered the reservoirs to be homogeneous. Definitive information is not yet available to show whether the actual presence of nonuniformities will make pressure transient behavior different from that of a uniform reservoir. The conclusions reached from actual transient tests are questionable, therefore, insofar as they rely on the original assumption of homogeneity. One type of nonuniformity commonly assumed to exist is that of stratification. In most reservoirs the strata are thought to be in vertical communication. Equations for the transient flow of a single-phase, compressible fluid in a one-well, bounded, circular reservoir have been solved for several situations involving crossflow between multiple strata of various thicknesses and permeabilities. The results show that except for the very early flow period, which usually is too short to be analyzed, the transient performance observed at the well is substantially identical with that of a homogeneous reservoir having the same dimensions and having the same steady-state flow capacity. Thus, stratification does not adversely affect interpretation of well transient tests. This conclusion holds for all commonly encountered combinations of reservoir thickness and external radius. Deviations are observed for unusually thick reservoirs whose outer radii are relatively small. The results of these studies also show that the presence and the amount of stratification cannot be simply diagnosed from reservoir pressure transient data when there is crossflow between strata. INTRODUCTION The last decade has brought wide acceptance of the transient well pressure test for determining reservoir parameters. Following the original work of Hurst and van Everdingen,1 the mathematical theory was thoroughly explored. Numerous authors have suggested how to determine static reservoir pressure, permeability-thickness product, original oil in place and reservoir limits for different reservoir geometry. The same mathematical techniques have been used to predict the transient performance of a reservoir over a long period of time. Most of the theoretical work has been for homogeneous, isotropic systems. Some results have also been presented for a homogeneous, anisotropic reservoir.2 Petroleum reservoirs are not homogeneous. The deposition process seems to favor creation of a stratified formation. This concept is sufficiently well accepted so that the most natural extension of the transient flow theory beyond the homogeneous case is to a stratified formation. Results for a stratified reservoir with no vertical communication between layers can be obtained from the results for a homogeneous reservoir. Lefkovitz, et a1,3 have given a thorough treatment of the two-layer case. Two recent papers4,5 have treated the case of a two-layered reservoir with vertical communication or crossflow, between layers. Russell and Prats4 find that, after a relatively short time, the two-layered reservoir with crossflow exhibits a simple exponential pressure decline. From this time forward, the behavior is not distinguishable from the behavior of a homogeneous reservoir having the same steady-state flow capacity. The results of Katz and Tek 5 are equivalent. Russell and Prats4 also speculate that a multi-layered reservoir with crossflow will behave as a homogeneous system after long enough production time "... providing the contrast in kh between layers is not too great". They also suggest that, at intermediate times, "... the relative positions of the layers with respect to each other will have a great influence on the production behavior and on the time at which the previously mentioned large-time approximation might be valid". Katz and Tek5 remark upon the mathematical difficulty of treating a reservoir having many layers or strata. If relative position of the layers is also

By J. M. Morris

The point to be made most clear in this paper is the economic value of flotation in the Benguet mill flow sheet. It is rather a statement of effect with no attempt at a technical explanation of the cause. Certain well-known, easily understood reagents, mechanisms and principles have been adapted to the conditions at Benguet, and have proved to be more successful than was demonstrated in the laboratory. The mechanical and metallurgical development of this particular operation was arrived at by trial and error, with fortunately very little error. Changes were slow, of necessity, which in the end proved a blessing in that time was afforded for observation and analysis of the disturbing factors; and as a result each change was a definite step towards higher efficiency. Many of these steps were unpredictable from laboratory work because of the varied and differing characteristics of ores met with in daily operation of the mill, which were practically impossible to reproduce on a laboratory scale. The Benguet mill receives daily ores that differ as much as if they were delivered from three different properties. There is first the surface and upper-level zone, which produces an oxidized secondary ore containing considerable iron oxide, manganese oxide and some organic matter. Formerly, most of this ore consisted of very soft fill with some hard rock mixed in. It also contained an unusual amount of iron and aluminum sulfate, which formed hydrates upon entering the alkaline cyanide solution and caused excessive frothing. When flotation was introduced in the Benguet mill the general characteristics of this upper-level ore had changed considerably, in that it was practically all newly mined, fairly hard ore. It still contained many of the same disturbing elements, but was somewhat simpler to treat than formerly. The small proportion of fines is still troublesome in flotation, and plant practice probably does not show more than 80 per cent extraction on this small portion of the ore. No definite figure on this is available, as this particular ore is delivered at irregular intervals

Jan 1, 1939

By Wallace Pratt

INTRODUCTION IRON-ORE deposits in the Philippine Islands became the subject of official record as early as 1664. Undoubtedly iron ore was known and recognized by the Filipinos long before the earliest Spanish records. It is even possible that the Filipino practice of smelting iron ore is, like the native copper smelting, older than the Spanish conquest of the islands. The first records have to do with the magnetite-hematite ores near the towns of Santa Inez and Bosoboso in Rizal Province, from 15 to 20 miles east of Manila. The magnetite-hematite ores of Bulacan were exploited in 1783. Similar ores near the town of Mambulao in Camarines Province yielded a number of specimens to be exhibited in Spain in 1834. With the exception, then, of the lateritic iron ores on the eastern coast of northern Surigao, the true nature of which was not recognized until 1914, the important iron-ore deposits of the Philippines had all been discovered before the islands came under the dominion of the United States. Indeed, in the Spanish documents relating to the history of iron mining are statements which, if their accuracy be not questioned, leave us in the Philippines today with much less iron ore than the Spaniards found. To quote, for example, a report submitted to the Superior Government in Spain in 1835 by one of its emissaries, Don Lorenzo Calvo: "The Philippine Islands, most excellent Sir, possess iron and exhibit it in nearly every known mineralogical combination, and in such abundance that the cordillera of the island of Luzon, from Montufar Point in San Bernardino Straits to Cape Bojeador, is composed of no other mineral than iron, its ranges, of the third order, being in content and structure totally iron of the best quality, the more valuable in that its combinations are such as to facilitate its fusion and to render its reduction to metal simple."

Jan 2, 1916

By J. M. Morris

The point to be made most clear in this paper is the economic value of flotation in the Benguet mill flow sheet. It is rather a statement of effect with no attempt at a technical explanation of the cause. Certain well-known, easily understood reagents, mechanisms and principles have been adapted to the conditions at Benguet, and have proved to be more successful than was demonstrated in the laboratory. The mechanical and metallurgical development of this particular operation was arrived at by trial and error, with fortunately very little error. Changes were slow, of necessity, which in the end proved a blessing in that time was afforded for observation and analysis of the disturbing factors; and as a result each change was a definite step towards higher efficiency. Many of these steps were unpredictable from laboratory work because of the varied and differing characteristics of ores met with in daily operation of the mill, which were practically impossible to reproduce on a laboratory scale. The Benguet mill receives daily ores that differ as much as if they were delivered from three different properties. There is first the surface and upper-level zone, which produces an oxidized secondary ore containing considerable iron oxide, manganese oxide and some organic matter. Formerly, most of this ore consisted of very soft fill with some hard rock mixed in. It also contained an unusual amount of iron and aluminum sulfate, which formed hydrates upon entering the alkaline cyanide solution and caused excessive frothing. When flotation was introduced in the Benguet mill the general characteristics of this upper-level ore had changed considerably, in that it was practically all newly mined, fairly hard ore. It still contained many of the same disturbing elements, but was somewhat simpler to treat than formerly. The small proportion of fines is still troublesome in flotation, and plant practice probably does not show more than 80 per cent extraction on this small portion of the ore. No definite figure on this is available, as this particular ore is delivered at irregular intervals

Jan 1, 1939

By R. W. D. Clarke, J. C. Folinsbee

INTRODUCTION This paper deals with a procedure for planning the mining of an orebody for which cross-sections, plans, grade of ore, and a geological estimate of the ore reserve have been prepared. The procedure begins with the preliminary selection of a mining method or methods on which an engineering evaluation will be carried out. The engineering evaluation is described in three parts: Conceptual Studies Engineering Studies Detailed Design An overall planning model is presented, plus an expanded model for the Engineering Study Throughout the discussion of the planning procedure, reference is made to three bulk mining methods, including block caving, sublevel caving, and longhole sublevel stoping, including a summary of the main characteristics of each of these mining methods. The planning model is designed for a longhole sublevel stoping method, but with modification, will apply to other methods. PRELIMINARY SELECTION OF A MINING METHOD To experienced mining engineers, identification of the nominal mining method for a given orebody normally involves a large measure of judgement. The geological data is reviewed to determine the configuration of the orebody, including size, shape, dip, grade, and metal distribution. Geotechnical data is considered, including the competence of the ore and host rock, faults, fracture patterns, groundwater, and the potential for in situ stresses. Geographical data, including the natural and societal conditions, are evaluated for their effect upon the mining method, and finally, economic data, basically defined as the value of the ore in the ground, but more specifically, including grade of mineable ore, distribution of ore grade throughout the orebody, and metallurgical recovery, will have a bearing on the nominal method selected. Preliminary evaluation of these factors will result in the elimination of the obviously inappropriate mining methods, leaving some method or methods for further, more detailed study. Since ore does not occur in simple geometric shapes, the method selected for more detailed study will require some variation to the standard. A few key factors will bear heavily on the selection and provide a basis for the most realistic choice. Geological Data The configuration of an orebody defined by the horizontal and vertical dimensions, the dip and strike, and the possibility of repetitive occurrences will have the major influence on the selection of the mining method. For bulk mining methods, the dip of the orebody should be steep, or the orebody must be thick so that gravity can be utilized to deliver fragmented ore to a central gathering area. Geotechnical Data The geotechnical data will be studied in greater detail when the nominal mining method has been selected and the engineering evaluation is undertaken. However, some basic initial information must be available. The structural strength of the ore and host rock, including the effect on it of faulting, fracturing, and insitu stresses, must be known. Data from exploration drilling and examination of drill core will assist in the preliminary assessment of these factors. Highly fractured ground may suggest a caving method of mining for certain orebody configurations, whereas highly competent or strong ore might indicate that for a similar configuration, longhole sublevel stoping will more likely succeed. Data obtained on groundwater from exploration drilling will be considered to determine if it can be controlled, or if it will represent a long term major expense or a hazard for which no control is possible.

Jan 1, 1981

THE CHAIRMAN (DR. A. R. LEDOUX).-If there ever was a question in the mind of anybody as to whether there are some mining engineers, I think if they would look in the door tonight they would decide there are. We meet here tonight not only to enjoy a smoke and other incidentals which are permitted us in these days, but with a more serious thought in our minds, because that flag, with its 540 stars, only begins to show the number of our membership that are serving the country. We are thinking of them, and when we consider how many of those men are also citizens of one or another of our allied countries, we can imagine that many are tonight thinking of us and perhaps have received, even at the front, notices of our annual meeting and are wondering what we are doing tonight; so our thought this evening will be going out to them, going out to those of our number who are serving in the khaki or in the blue, or in other activities denied to some of us for one reason or another; but, gentlemen, there is one thing we will do now, we will rise and sing together r the Star Spangled Banner. Gentlemen, not only are American citizens here tonight, not only representatives of our country on the Speakers' platform, but. there are representatives of our Allies, and we are going to have the privilege of listening to one or two of the latter, a citizen of the great British Empire and a citizen of France. We will first have the pleasure of hearing Capt. Hodder-Williams. He has been loaned to us to take charge of training Columbia University students, after two years or more in the trenches, and lie carries with him the only German thing in this room, a German bullet in his shoulder. That has not affected either his spirit or his

Jan 4, 1918

By A. C. Fieldner, F. H. Gibson, W. A. Selvig

A foRmer paper1 described in detail various methods of calculating coal analyses to obtain the composition and calorific value of the pure coal substance—that is, of the coal free from its mineral matter. The paper included a table showing calorific values of pure coal, as calculated from float-and-sink portions, by means of the Parr formula for "unit coal" and by the customary moisture-free and ash-free formula. A modification of the Parr formula was proposed, based on the assumption that one-half the sulfur present in Coal occurs as pyritic sulfur and one-half as organic sulfur. In the published discussion of the paper Cady gave a table of results on a large number of Illinois coals as obtained by the Parr formula and the proposed modification thereof. The results obtained by Cady indicate that the Parr formula applies better to Illinois coals than does the modified formula proposed by Fieldner and Selvig. The present paper gives results obtained by applying the modified Parr formula to the analyses of the float-and-sink portions of the coals shown in the former paper, and results obtained by applying the Parr formula, the modified Parr formula, and the simple moisture-free and ash-free formula to various coals of the United States ranging in sulfur content from less than 1 per cent to more than 4 per cent sulfur. A graphic method of estimating the calorific value of pure coal and determining the relation of the coal ash to the mineral matter of coal, as proposed by Stansfield and Sutherland,2 was applied to a number of coals, and the results are given herein. Testing Formulas with Float-and-sink Separations The former paper by Fieldner and Selvig gave heat values of pure coal of the float-and-sink portions of 21 coals, as calculated by the Parr formula

Jan 1, 1932

By B. D. Thomas

GRAVITY concentration is a general term designating processes for separating and sorting granular material by means of forces that depend on the density, size and shape of the particles. When these forces are applied to the particles the latter are caused to move, those of a given density along one path and those of a different density along another, until ultimately they are sufficiently separated to be removed from the operation of the process. The forces producing this separation are in general complex and, unfortunately, no completely rigorous analysis of them has as yet been devised. The science of the hydrodynamics of viscous fluids deals with the little that is known about the problem. Every observer of nature is familiar with the fact that an object moving in a fluid encounters a force of resistance. We have only to walk against a brisk wind or stir a cup of coffee, or observe the slow fall of a grain of sand in water, to experience directly the fact that such forces exist. The exchange of force between an object and a fluid in which it is moving operates on the fluid as well as on the object. Thus a sailboat may be set in motion by the force exerted by the wind on the sail; but the sail also deflects the wind-furthermore, the water in which the boat floats is set in motion by the force exerted by the boat as it cleaves through the water. The wind is thus enabled to do work on the water through the intermediary of the boat. In general, an object moving through a fluid encounters a force that opposes the motion and also acts to change the motion of the fluid. In gravity concentration we are dealing with this force of resistance acting on the granular particles that are to be separated. Furthermore, the motion induced in the fluid by a particle will in turn affect the motion

Jan 1, 1943

By J. B. Berkowitz-Mattuck, R. Hopper, L. Kaufman, E. V. Clougherty

MARNOCH has reported on the attractive high-temperature oxidation resistance of Hf-Ta alloys.' In view of current interest in these alloys, three Hf-Ta alloys were tested in the present study. These included a Hf-27Ta alloy and a Hf-20Ta-2Mo alloy which were supplied by Marquardt Corp. and a Hf-20Ta-Zr alloy provided by Illinois Institute of Technology Research Institute.' The microstructure of these alloys was heated inductively in a glass vacuum system; the oxidizing gas, helium carrier plus a known partial pressure of oxygen (35-102 Torr), was continually passed over the sample at temperature for a given time period. The concentration of oxygen in the gas stream was continuously measured by a differential thermal conductivity technique2 so that the rate of oxygen picked up by the sample could be obtained. The flow rates were 0.1 to 0.2 ft per sec in the vicinity of the specimen. The concentration of oxygen did not fall below 50 pct of the input level in any of the experiments. In several cases a single sample was exposed consecutively at a series of increasing temperature levels. In a second system at ManLabs, cylindrical specimens were exposed to flowing air in a z irconia tube which was heated by radiation from a carbon tube resistance furnace. The specimen was heated from room temperature to the test temperature in flowing argon, then oxidized in air flowing at 0.1 to 0.2 ft per sec. Following exposure, the air was displaced by argon and the specimen was cooled. Postoxidation metallography was performed on every sample. The depth of conversion of the metal matrix to oxide was measured as shown in Fig. 1. The conversion depth was obtained by measuring the oxygen-contaminated metallic zone (which is bounded by a dense outer oxide and a subscale oxide region), subtracting its dimensions from the original dimensions, and dividing by two. Preferential oxidation of

Jan 1, 1968

By W. H. Howard

As the result of a series of analyses and volume determinations of gases discharged from the converters at the Garfield Smelting Co.'s smelter at Garfield, Utah, it was found that a considerable amount of lead fume was escaping from the stacks of the converter plant, and that if this lead could be recovered at a reasonable expense an attempt should be made to collect it. Two methods suggested themselves: (1) filtration through bags; (2) electrical precipitation of the condensed fume by a Cottrell plant. Filtration through Bags Tests were made in filtering converter gases through the ordinary woolen bags of lead-smelter bag houses to determine how long such material could withstand the corrosive action of the gases. While blowing on white metal only, the fabric was usually destroyed in 10 to 14 hr. In tests conducted in filtering gases when blowing on matte or slagging stage exclusively and when relatively considerable lead was being volatilizcd, bags in one instance lasted 60.5 hr. It therefore was evident that the Garfield converter gases did not contain in themselves sufficient neutralizing elements for the purpose of direct bag filtration, even during the slagging stage. Such results were more or less anticipated, but it was thus proved that under all conditions of blowing Garfield mattes a very considerable amount of neutralizing agent, zinc oxide or lime, or both combined, as in the Sprague process, would be required to render bag filtration possible. Again, owing to the constantly changing quantities of SO3 from a given battery of converters, depending on the number blowing at a given time and on the stages of the blow, it would be practically impossible to feed automatically the required amount of neutralizer. In order to safeguard the bags sufficient neutralizer would have to be continuously added to meet the maximum SO3 output, thus wasting neutralizers and giving an undesirably diluted final product. Such a condition is entirely different

Jan 1, 1915

By Charles H. Behre

UNDER the caption "fault," geologists intend to include all mass movements of solid rocks over adjacent rock masses. When these are studied long after their origin, however, circumstances make it possible to recognize as "fault" only formations showing clear evidence of actual movement of one side with respect to the other. Necessarily the chief evidence consists of the offset of a vein, bed, or other key structure. Planes of movement parallel to the bedding, or nearly so, are recognized with difficulty or are overlooked and hence many important faults are wholly unrecorded. Indeed, among standard American references on structural geology, one alone emphasizes the importance of bedding-plane movements and that one only briefly1. For some time the writer, cognizant of this difficulty, has paid special attention to such movements, both as observed in the field and as recorded in the literature. It is believed that enough data are now at hand to justify a short discussion. Its purposes are fivefold. It is desired first to briefly classify and describe at least the more common kinds of bedding-plane faults, and second, to examine the causes and manner of their formation, at least in instances where the subject has not yet been well covered by other investigators. Third, certain by-products of bedding- lane movements are of such conspicuous importance to the economic geologist and mining engineer as to merit mention. Fourth, concrete illustrations should be placed before the reader in order to lend reality and to furnish a basis of comparison with his experience; such illustrations will necessarily be scattered through the text of this paper. They are only in part from the writer's own field observations. The fifth and prime objective of this paper is to direct attention to the great importance of movements on the bedding planes, in the hope that the recognition of such movements and their significance may simplify mining problems.

Jan 1, 1937

By Charles Barrett

THE experiments reported in this paper have been fruitful in disclosing the mechanism of the deformation of iron in compression. They have established the nature of "deformation bands," "etch bands," or "X-bands," that have been a recognized but little understood feature in the structure of cold-worked metals since the early days of metal-lography, and have shown the role of the bands in the development of preferred orientations by cold-working. The work has also shown the relation of the orientation of individual grains to the preferred orientation of the aggregate. Some of the methods previously used in the determination of the indices of slip planes and slip directions are shown to be untrustworthy in the presence of deformation bands. The conclusion is reached that many slip planes and slip directions must operate during each stage in the compression of a single crystal, and that theories failing to take account of this require revision. In conducting the experiments a method f compression has been used by which extreme reductions can easily be reached, even to the limit set by the metal's capacity to deform with-out fracture. The work is a portion of a research program on the plastic properties of iron and steel. It is being used as a foundation for studies of orienta-tions resulting from recrystallization and is being extended to other metals and other types of deformation.

Jan 1, 1938