Search Documents

By M. Semchyshen, G. A. Timmons

P. A. Beck (University of Illinois, Urbana, 111.)—An interesting result of this work is the fact that in cold rolled molybdenum sheet complete loss of work hardening is obtainable on annealing, without change in texture. The retainment of the cross-rolling texture on soft-annealing is particularly significant, since this is essentially a single orientation texture, where texture retainment could be achieved by only one of the two niechanisms which produce this effect in aluminum,16 namely by recrystallization in situ. Recrystallization in situ was originally discovered by Collins and Mathewson (1940) and by Crussard (1944) as a phenomenon taking place on annealing in relatively mildly deformed single crystals of aluminum. It now appears to be a major (in many cases the major) mechanism of annealing of severely cold rolled poly-crystalline material, not only in aluminum,le but in metals as different in character as beryllium," tita- nium,'" and molybdenum. All these data now confirm the general validity, at least for more or less pure metals, of the interpretation of the annealing process given a few years ago by Smith.'" The whole question of recrystallization is now reopened. Indeed, it appears that recrystallization, as defined traditionally, may not occur at all, since at the time "deformed material" is absorbed by "recrystallized grains," it has already become completely strain free by recovery and "recrystallization in situ."

Jan 1, 1953

By K. J. Miller, R. E. Hucko

The Coal Reparation Division of the Pittsburgh Mining Technology Center conducted an investigation to assess and compare the pyritic sulfur reduction potential of coal-pyrite flotation and high-gradient magnetic separation (HGMS). Tests were run on three coals - an Upper Freeport bed coal, a Lower Kittanning bed coal, and a Pittsburgh bed coal - to establish grade-recovery relationships characteristic of both processes. Representative portions of each coal sample were crushed to two top sizes-nominal - 500 pm (-35 mesh) and nominal - 149 pm (-100 mesh)-and subjected to conventional froth flotation. The froth product was then beneficiated by coal- pyrite flotation or HGMS, to provide a direct technical companion of the two processes. At - 500 pm (- 35 mesh), the size normally employed for coal flotation, both coal-pyrite flotation and HGMS effectively separated pyrite from coal, and the performance of the two processes was essentially the same. At a - 149 pm (- 100 mesh) sire, however, the performance of HGMS exceeded that of coal-pyrite flotation. The separation effected by HGMS were more efficient at - 149 pm (- 100 mesh) than at - 500 pm (- 35 mesh). On the other hand, it was concluded that either the effectiveness of coal-pyrite flotation decreases with diminishing top size or the process has not been optimized to treat material finer than 500 pm (35 mesh).

Jan 1, 1983

During 1918, the activities of the United Engineering Society, the Library, the Engineering Foundation, and Engineering Council Were deeply affected by the war and much important war work Was done in our building. The endowment of Engineering Foundation was increased to $300,000 by an additional gift of $100,000 from Ambrose Swasey. By bequest of Dr. James Douglas, the American Institute of Mining Engineers received an endowment of $100,000, the income of which Will be expended in the maintenance of its library (now a part of the joint library). The Library Service Bureau has gained steadily; its business for 1918 amounted to nearly $10,000. Indexing of current engineering literature has been undertaken in conjunction With the Founder Societies and the Index is being printed in their publications. This service has been extended to the Engineering Institute of Canada and the Canadian Mining Institute. The expense is borne by the Societies. In this connection the American Society of Mechanical Engineers has purchased the Engineering Index heretofore published by "Industrial Management." In June the Westinghouse and General' Electric Co. donated to the United Engineering Society their Patent Con¬trol Library of about 8000 volumes. Other noteworthy gifts Were a collection of 370 pieces relating to patent litigations, from Jesse M. Smith, and Dr. William Paul Gerhard's collection on gas engineering, transferred by the American Gas Association.

Jan 1, 1923

By U. Paakkinen, P. Eerola

In connection with theoretical studies of the dynamics and control of the flotation process, flotation cells and circuits at the Pyha- computer control of selective Cu - Zn - Fe sulfide flotation in the latter half of 1969. In this paper, the practical conclusions of these studies, conducted through simulation techniques, are summarized. The application of these results for control purposes implies a knowledge of the dependence of the flotation rate coefficients and the grade of concentrate on several factors, including aeration rate, froth depth, and reagent consumption. The relationships found in laboratory and plant scale tests are described. Off-line optimization studies, based on the relation- ships, are also described. The proposed steps in executing the computer control schedule are presented. In the first stage, a stabilizing control will be carried out using feed-back loops. A feed-forward control system which utilizes simple process models will also be tested. After these elementary stages, a proposed mathematical model of the circuit will be checked out and implemented with computer- run, plant-scale process tests. Off-line simulation will be continued in advance development of the control system. As a final step in the program optimal control of the process will be carried out through this model.

Jan 1, 1969

By Monte J. Pool, Rudolph Speiser, George R. St. Pierre, William T. Ebihara

Standard free energies of formation of WO,, W O W20058 and WO3from oxygen and the lower oxide or tungsten have been determined in the tempel-ature range of 700° to 1220°C. A tentative W-O phase diagmm is presented based on the evidence that the oxide phases, "W18O49" and "W20058", are unstable at l~atm total pressure, below 585° and 485°C:, respectively. A HE need for a complete quantitative treatment of the phase equilibria of the W-O system has been establishedby metallurgists during the past few years. In an attempt to improve the endurance of tungsten exposed to oxidizing atmospheres at high temperatures, many research groups have studied the kinetics of tungsten oxidation. The reverse process, the reduction of the tungsten oxides to metal, has also been investigated to some extent. Regardless of the particular interest, metal to oxide or oxide to metal, a knowledge of the phase equilibria of the W-O system is required to properly interpret all of the kinetic observations. It should be possible to state the stable phases of the W-O system at any given values of the chemical potential of oxygen and the temperature.

Jan 1, 1962

By Samuel S. Wyer

The following description of methods for conducting gas-producer tests is probably the first attempt to give the subject an analytical, thorough and comprehensive treatment. In some cases where tests have been made, the methods have been so unsystematic and ambiguous that it has been impossible to secure comparable results. To eliminate this difficulty, the following provisional code of gas-producer tests— which has some resemblance to the code of boiler-trials of the American Society of MechanicalEngineers—has been developed. The primary object in testing a gas-producer is to determine whether the producer is working satisfactorily or, what is the same thing, to see if the efficiency is as high as it should be with the type of producer in question; and also to find out if the composition of the resulting gas is adapted to the work it has to do. In order that the test shall be of any value, it must be thorough and comprehensive, and must be conducted with skill and care. When so conducted, the test will reveal the economy of the'producer; and, by making suitable changes, the efficiency will often be increased very much. As a result of the tests made by Jenkins,' the efficiency was raised from 56.2

Jan 1, 1906

Joseph HartshoRnE, Pottstown, Pa.: I have read Professor Akerman's valuable paper with great interest. Few of the present generation of American steel metallurgists are aware of the very important part taken by Swedish engineers in the successful development of the Bessemer proeess, and I am afraid some of the older ones have forgotten it. Certainly, I think, most of us would have said that Terre Noire was the first to introduce the use of metal direct from the blast-furnace. It is very well, therefore, that honor should be given to whom honor is due. I can speak from personal experience upon one part only of Prof. Akerman's paper; namely, the effect of the temperature at which the molten metal is cast upon the quality of the finished steel. In a general way I have, of course, known for a long time that the

Jan 1, 1894

By Joseph E. Pogue, F. G. Coqueron

Prior to 1934, published information covering expenditures by oil companies for properties, plant, and equipment and the residual investments in the various segments of the petroleum industry was not readily available. This paper presents an analysis of the funds invested by a selected group of oil companies during the years 1934 through 1942, based on an extensive study of the individual records of 30 oil companies. The sources, disposition, and characteristics of the capital employed by this group of companies are traced through a series of combined statements and appropriate charts, covering financial and operating data. The analysis of these statements not only constitutes a record useful for comparative purposes but also serves as a basis for a number of broad conclusions, as follows: 1. The petroleum industry generates the capital needed for its expansion almost entirely from its own operations and is therefore a singularly self-contained economic unit. 2. The long-term debt contained in the financial structure of the industry is small relative to the total capital employed, is less than the net working capital, and has increased but slightly during the period under review. 3. The capital expenditures of the group of 30 oil companies for 9 years amounted to 6.1 billion dollars, 58.3 per cent of which went into crude-oil producing facilities. The trend of this segment of expenditures has been downward since 1937. In 1942, expenditures for refining facilities increased sharply and for marketing facilities declined drastically. 4. The net working capital of the group increased 380 million dollars over the period, and the industry is in a favorable position of liquidity. The ratio of combined current assets to current liabilities was 3.21 at the close of the period. 5. The net income of the group displayed an upward trend for the period but with rather sharp cyclical fluctuations. 6. In 1942, Government funds entered the industry for the first time in substantial amounts and were utilized for the provision of war facilities needed for emergency use. 7. The group has paid out a relatively low percentage of net income in the form of dividends. For the period the average was 55 per cent of net income. 8. The rate of return on invested capital for the group averaged 6.4 per cent for the

Jan 1, 1944

By Joseph E. Pogue, F. G. Coqueron

Prior to 1934, published information covering expenditures by oil companies for properties, plant, and equipment and the residual investments in the various segments of the petroleum industry was not readily available. This paper presents an analysis of the funds invested by a selected group of oil companies during the years 1934 through 1942, based on an extensive study of the individual records of 30 oil companies. The sources, disposition, and characteristics of the capital employed by this group of companies are traced through a series of combined statements and appropriate charts, covering financial and operating data. The analysis of these statements not only constitutes a record useful for comparative purposes but also serves as a basis for a number of broad conclusions, as follows: 1. The petroleum industry generates the capital needed for its expansion almost entirely from its own operations and is therefore a singularly self-contained economic unit. 2. The long-term debt contained in the financial structure of the industry is small relative to the total capital employed, is less than the net working capital, and has increased but slightly during the period under review. 3. The capital expenditures of the group of 30 oil companies for 9 years amounted to 6.1 billion dollars, 58.3 per cent of which went into crude-oil producing facilities. The trend of this segment of expenditures has been downward since 1937. In 1942, expenditures for refining facilities increased sharply and for marketing facilities declined drastically. 4. The net working capital of the group increased 380 million dollars over the period, and the industry is in a favorable position of liquidity. The ratio of combined current assets to current liabilities was 3.21 at the close of the period. 5. The net income of the group displayed an upward trend for the period but with rather sharp cyclical fluctuations. 6. In 1942, Government funds entered the industry for the first time in substantial amounts and were utilized for the provision of war facilities needed for emergency use. 7. The group has paid out a relatively low percentage of net income in the form of dividends. For the period the average was 55 per cent of net income. 8. The rate of return on invested capital for the group averaged 6.4 per cent for the

Jan 1, 1944

Diffusion in Solid Metals. BY ROBERT F MEHL (Institute of Metals Division Lecture Tech Pub 726 in Metals Tech, Aug , also Trans, vol 122 22,500 words ) Diffusion in solid metals constitutes one of the important fundamental phenomena in metallurgical behavior Apart from its obvious importance in processes such as chromizing, carburizing, nitriding and calorizing, it plays an important part in the processes of homogenization, age-hardening, and transformations in steel, its scientific importance is no less great Diffusion may occur within a grain, along a grain boundary, or upon a surface, though the exact and even the relative values of these separate processes are known for only a very few cases The requirement of solid solution formation presents the possibility of identifying solid solution phases by a study of diffusion layers Some distortion accompanies diffusion, leading to little¬ understood grain-size changes Distortion assists diffusion though usually it dis¬appears before diffusion has become extensive In a binary system the rate of diffusion is the more rapid in the lower melting metal Many of the published data are too qualitative to permit sound scientific conclusions Age-hardening data may be treated as diffusion data and rates of reaction in steel could profitably be studied from this point of view Studies on diffusion are of great importance to the develop-

Jan 1, 1937

By Robert L. Voss, Richard D. Hagni

Sparry dolomite from all of the operating mines in the Viburnum Trend of Southeast Missouri have been found by cathodoluminescence microscopy to reveal a systematic pattern of banding resulting from a growth zoning within individual dolomite rhombs. Four principal bands have been recognized throughout the entire Trend and each of the major bands contain even finer internal banding. Minor bands a few microns in width can be correlated in specimens collected ten's of kilometers apart along the trend. The first three principal dolomite bands decrease from south to north. This feature, together with the fact that the white sparry dolomite crystals decrease in abundance from south to north in the Trend, suggests that a major source for the fluids was from the south. The application of cathodoluminescence microscopy to crystalline dolomite demonstrates a strong correlation between ore grade and the intensity of internal banding and dissolution textures.

Jan 1, 1985

By J. M. Smith, D. Kunii

Effective thermal conductivities of sandstones filled with stagnant fluids were measured using a steady-state technique. Data were obtained for seven sandstone samples, taken from four different locations and ranging in permeability from 18 to 590 md. The measurements with gases (helium, nitrogen, air and carbon dioxide) covered a pressure range from 0.039 psia to 400 psig. Data were taken for four liquids — n-heptane, methyl alcohol, 79.8 weight per cent glycerol-water solution and pure water at atmospheric pressure. The experimental results were used to evaluate the theoretical equations for predicting stagnant conductivities developed earlier 4 The low-pressure measurements permitted evaluation of the consolidation parameter bpDp/ks (necessary to utilize the theory) for the various types of sandstones. Using these characteristic values, the tbeoretical equations correlated well with the experimental conductivity data for the several fluids and rock samples. INTRODUCTION An aspect of heat transfer in solid-fluid systems of considerable current interest is the effective thermal conductivity of porous media. The stimulus for study of the subject arises from the need for sound procedures for designing thermal methods of petroleum production. The general system occurs when there exists a flow of fluid through the pores of the solid material. However, a logical starting point in developing a theory for predicting the effective thermal conductivity in the general system is to attack the special case when the porous solid is filled with stagnant fluid. Since the flow rates anticipated in thermal production processes are very low, such stagnant conductivities k,O are also of practical significance. Kunii and Smith4 recently reviewed the existing data for stagnant conductivities and proposed a theory for heat transfer in porous rocks. This leads to equations for predicting the stagnant conductivity as a function of the properties of the fluid and solid phases. The existing experimental information1-3,5,7,8 covered a range of porosities and agreed well with the theory. However, the available data were insufficient to examine critically the effects of two important properties on koe, — the thermal conductivity of the fluid and the pressure. The objectives of the present study are twofold: (1) to measure the effect on koe of (a) the pressure for gases, and (L) the thermal conductivity of the fluid kg for bloth gases and liquids; and (2) to determine for rocks of different porosities and permeabilities the apparent solid conductivity ks and the consolidation parameter bpDp/ks required in applying the theoletical equations. Measurements extrapolated to zero pressure are helpful in evaluating ks and the consolidation parameter. However, the extrapolations must be based upon data obtained at low pressures because in small pores the molecular conductivity of the fluid may be unusually depressed. This occurs when the mean free path of the molecules is of the same order of magnitude as the pore diameter, that is, in small-diameter pores at low pressures. The phenomenon has been studied recently by Schotte6in beds of unconsolidated fine particles. With particles in the size range of 45 to 200 microns, a significant reduction of kg with pressure was found even at absolute pressures greater than 1 atm. In the sandstones employed in the present investigation, pore diameters lower than those experienced by Schotte are likely, so that the effect would presumably be greater. SCOPE OF MEASUREMENTS Stagnant conductivities were measured for four types of sandstones using a total of seven samples. The characteristics of the samples, including porosity and permeability values, are given in Table

By D. F. Kaufman, E. D. Levine, L. R. Aronin

ThE primary slip plane in hcp metal crystals can usually be inferred from the c/a ratio. Basal slip is the primary system at room temperature for zinc, cadmium, magnesium, cobalt, and rhenium, all of which have a c/a ratio greater than 1.60. Zirconium and titanium, on the other hand, each with a c/a ratio of 1.59, deform primarily by (1010) [ll20] prismatic slip. The increasing tendency toward prismatic slip in these materials is generally thought to be associated with the increase in atomic density on (10i0) as c/a is reduced. Beryllium, with a c/a ratio of 1.57, would, according to the above scheme, be expected to exhibit prismatic slip. However, in beryllium of commercial purity, the primary deformation mode at room temperature is basal slip.' The ratio of critical shear stress for prismatic to that for basal slip at room temperature is approximately 5:l. The critical shear stress for prismatic slip decreases quite rapidly with increasing temperature, however, and at 500°C the ratio is approximately unity. The apparently anomalous behavior of beryllium has led to speculation that prismatic slip in this material may be restricted by an anisotropic effect of impurities,' and that, if beryllium could be purified to a sufficient extent, prismatic slip might predominate at room temperature. In such a case, the conditions under which basal cleavage can occur would be suppressed, and enhanced low-temperature ductility might result. With the advent of the floating-zone method for purification of beryllium,3 it has become possible to determine experimentally the effects of purification on basal and prismatic slip. Tensile tests were performed at room temperature on single crystals oriented favorably either for basal or prismatic slip. The crystals had been purified to various extents by zone-refining, employing procedures that have been described elsewhere.4 Relative purities of the crystals were estimated by measuring the ratio of electrical resistance at 4.2"K to that at 298°K. Typical values ranged from 0.40 for commercial-purity material to 7.7 X 10"4 for crystals prepared from vacuum-distilled beryllium and subjected to six zone-refining passes. The purity dependence of the critical shear stresses for basal and prismatic slip is shown in Fig. 1. In the purity range studied, the critical shear stress for basal slip is decreased from 1.4 to 0.14 kg per sq mm. The critical shear stress for prismatic slip is decreased from 6.7 to 5.3 kg per sq mm. The decreases in critical shear stress for each deformation mode, therefore, are approximately equivalent. No purification anisotropy is observed. Because of the absolute magnitudes of the critical stresses, the ratio of the critical shear stress for prismatic slip to that for basal slip actually increases from 5:l to 38:l at the highest purity level studied. It is evident, therefore, that basal slip is the primary deformation mode in high-purity beryllium. This fact must be accounted for in any rationalization of the deformation behavior of hcp metals. This work was performed at Nuclear Metals, Inc., under the sponsorship of the U.S. Atomic Energy Commission.

Jan 1, 1964

By J. Price Wetherill

The coal-seams that are worked vary from 3 1/2 to 100 feet in thickness, and occur at all angles of inclination, but are never flat for any great extent. They contain coal, slate, and an unsolidified coal, called dirt by the miners, in various proportions, a uniform seam of coal alone being rare. The upper walls are composed of conglomerate, sandstone, or slate; the first two hard and solid in texture, and withstanding the action of the atmosphere and moisture sufficiently well to offer but little trouble to the mining operations; while the latter crumbles rapidly, owing, in part, to the decomposition of iron pyrites which it contains in large quantities, and in part to its own friable character, and requires constant care to avoid accidents to the men working below it, and to prevent its mixing with the coal mined. The floors are composed of slate. As in all mining operations, the general system pursued is to reach with a permanent outlet such a point in the seam as will

By R. W. Diamond

THREE mills are now operated by the Consolidated Mining & Smelting Co. of Canada, Ltd. : (1) The Sullivan Concentrator, Chapman Camp, B. C. (near Kimberley, B. C.), (2) the St. Eugene Concentrator, Moyie, B. C., and (3) the Tadanac (Customs) Concentrator, Trail, B. C. Differential flotation is the only concentration method employed in all three I plants. Tables are used for pilot work only. Values in all ores treated are as minerals of some or all of the metals -lead, zinc, gold or silver. Occasional customs ores contain small amounts of copper. Sulfide iron content of ores treated varies from a [ ] low figure in some ores to 38 per cent. iron in Sullivan ore. Gangue minerals vary considerably. A few customs ores are somewhat oxidized and as a result present difficulties. Flotation equipment and control are similar in the three mills, and the flow sheets at the St. Eugene and Tadanac mills, while much simpler, are modeled after that of the Sullivan Concentrator. In this paper I will not detail treatment nor equipment in any of our plants but will describe special features in, or in connection with, all of them. I will then deal with flotation reagents, describing our use of each of them, particularly where differing from general practice. I will conclude with comments on special subjects related to differential flotation.

Jan 1, 1928

WHEN Georgius Agricola, in 155o, dedicated his now famous De re Metallica to the rulers of Saxony, Thuringia, Meissen, and other, smaller principalities, he included in his review of previous works on similar subjects reference to two books written in German: one, an "anonymous, rather disorganized account of assaying for metallic content and of metals," which must be the Probierbüchlein, the other, "dealing - with veins, written by Calbus of Freiberg, a well-known physician."* Calbus is mentioned a second time-and cited-at the end of the Third Book of De re Metallica. Comparison of the citation with the Bergbüchlein leaves no doubt that Agricola considered Calbus of Freiberg the author of the latter work, although all the editions of the Bergbüchlein known now were published anonymously. It is generally accepted by those who have dealt with the bibliography of the Bergbüchleint that Calbus was Ulrich Rülein von Kalbe, who served the City of Freiberg, in Meissen, as health officer in 1497, as member of the City Council in 1509, and as mayor in 1514 and 1519. He died at Leipzig in 1523. In connection with the very garbled description of the mining compass toward the end of Chapter 3 of the Bergbüchlein it is of interest that von Kalbe is supposed to have been not only a physician of repute but a mathematician, astronomer, mine sur-

Jan 1, 1949

By B. S. Butler

STUDY of the ore deposits of Colorado has disclosed, in numerous places, sharp changes in both mineralogy and metal content of the primary or hypogene deposits with change in depth. A clear understanding of the meaning of these changes is requisite to form intelligent conclusions that can be applied in the exploration of such ore deposits. This paper is an attempt to set forth some of the geologic and chemical relations of minerals that bear on this problem. The effect of the differing electrode potentials of elements on the order of oxidation and on the order of displacement of one metal by another metal in supergene sulfide deposits has been studied for many years by several investigators. The results all agree rather closely with the original Schürmann series of replacability of metal sulfides, as Wells has shown.1 So far as the writers are aware there has been little attempt from the geologist's viewpoint to correlate the electrode potentials of the elements, other than those of the common metals, with the positions and mode of combination of the elements as found in ore deposits, and in particular in hypogene deposits. Wells2 discusses electrochemical activity between solutions and certain ore minerals and mentions the possibility of its effect in precipitation reactions.

Jan 1, 1929

By C. L. Dake

Iron is much more soluble in the ferrous than in the ferric form. Where, as in the case of the ferrous silicates and. the sulphides, the iron is already in the ferrous form, it may go at once into solution and be removed, upon the breaking down of the parent rock. If in the ferric form, it must first be reduced; usually by the decay of organic matter, the demand of the decaying carbonaceous matter for oxygen being so great that the latter is abstracted from the ferric compounds and the iron is thereby reduced and rendered soluble. The iron may go into solution as the sulphate, or in the presence of excess CO2 as ferrous carbonate. It is probably soluble as salts of the organic acids.' Recent work indicates that these are important in the formation of bog ores.2 There is considerable variety of opinion concerning the behavior of these organic compounds.3 The secretions about the roots of plants and trees also cause the solution and removal of iron and a consequent bleaching of the soil,4 While the matter is not yet well understood, we can probably say definitely that the so-called organic acids are a group of colloids which possess slightly acid properties, and the salts of which are partly soluble and partly insoluble.5 Their iron salts readily change from the ferrous to the ferric form, and their solubility is greatly modified by the presence of ammonia.

Jan 1, 1916

By N. J. Grant, Masao Adachi

A number of Cu-SiO, and Cu-A1203 alloys of low oxide content, produced by internal oxidation of copper-silicon and copper-aluminum dilute solid solutions, were exposed at temperatures up to 1050°C for fairly long times to bring about partial or total re crystallization. The creep-rupture properties of these re crystallized alloys were compared to those in the as-extruded condition at 450° C. Some of the alloys were cold worked after re crystallization to note changes in creep-rupture properties, also at 450OC. SINCE the introduction of the SAP alloy in 1949,~ many studies have been carried out on similar oxide and intermetallic dispersion hardened alloys to determine properties and to establish the mechanisms involved in the strengthening process which led to stable, high-temperature behavior.'-' To date, it has been indicated that, however achieved, the structure should be composed of a continuous ductile metal matrix in which is dispersed a fine, submicron size, hard, insoluble second phase (or at least, essentially insoluble at temperatures very near the melting point), with a submicron or near submicron interparticle spacing. Stored energy, obtained by a high strain rate deformation process appears desirable, as an additional strengthening means beyond pure dispersion.=

Jan 1, 1961

By C. W. Spencer, F. N. Rhines, R. J. Knight

Ametallographic study has been made of the peritectoid transformation as it occurs in two Ag-A1 alloys, containing 6.0 and 6.9 wt pct Al, respectively. After equilibrating at 475°C, these alloys were transformed isothermally just below the peritectoid temperature which lies at about 450°C.1-3 Peritectoid transformation in this alloy system consists in the reaction of a and 5 to form µ. The crystal structures of the a, µ, and 5 phases have been determined as face-centered-cubic, 6 manganese, and hexagonal-close-packed, respectively. At the peritectoid temperature their equilibrium compositions are approximately 5.85, 7.02, and 7.24 wt pct (19.92, 23.2, and 23.8 atomic pct) aluminum."" The transformation might be expected to occur principally at the interface between the a and 5, but such is not the case. Instead, the major part of the transformation occurs by the direct (and perhaps initially diffusionless) conversion of 5 to µ. The composition range of the forming µ nearly overlaps that of the parent at the temperature of transformation" so that little, if any, composition change is required. Transformation proceeds by the nucleation of µ at points upon the external surface of the sample and sweeps through the 5 phase, leaving the a initially almost undisturbed. Subsequently, the a phase participates in the transformation by being partly or totally converted to µ. Specimens approximately 1/4 x 1/4 x 1/16 in. were cut from cast ingots, previously equilibrated 68 hr at 588°C. The specimens were held for 3 hr at

Jan 1, 1958