Search Documents

By S. Skowronski

PURPOSE OF INVESTIGATION Since cuprous chloride melts at 418° C., boils at 954° C. to 1033° C.,1 and is known to be volatile at a much lower temperature, the presence of chlorine in any form in or on copper to be melted has always been looked upon by copper refiners as a possible source of-serious copper loss. Although this fact has been known for some time, the copper literature contains little or no information regarding it and the field seems .never to have been properly investigated from a metallurgical standpoint. According to Greenawalt,2 cupric chloride, CuCl2, when ignited gives cuprous chloride; therefore cuprous chloride is always formed when copper enters into reaction with chlorine at a high temperature. Cuprous chloride melts somewhat below a dull red heat, and does not volatilize in closed vessels, even if strongly heated, but if heated in the air it goes off as a white vapor. Hofman3 gives the melting point of cuprous chloride

Jan 2, 1919

By L. Massé, Th. Koulomzine

Note on Haalck's Formula Quantitative interpretation of magnetic anomalies is admittedly a difficult process. Few authors have attempted a general approach to this problem. A number of publications can be found widely scattered through scientific periodicals, which present particular solutions obtained by the introduction of simplifying assumptions, such as the reduction to an equivalent magnet or pole, or the hypothesis of a very thin vein. The practical applications of these solutions are necessarily very restricted though they have given satisfactory results in isolated cases. Probably the most widely known equation of this type was given by Haalck.' His classic work contains curves calculated for typical conditions, and has now become a standard reference. However, a close scrutiny of Haalck's derivation reveals that, aside from the hypothesis of a thin vein, it rests on the

Jan 1, 1949

By H. S. Hanna, C. Rampacek

The problems and limitations encountered in the Physical beneficiation of the Appalachian Red Iron Ores are discussed. Two major problems are identified - the high phosphorus content and the fine dissemination or encapsulation of mineral impurities in the iron-bearing minerals. A process that combined extreme fine grinding techniques with magnetizing roasting or flotation-separation methods is suggested. By these methods, concentrates assaying 60-61 % Fe, exceeding the widely accepted upper limit of 56% Fe set for these ores, were produced with 75-90% iron recovery. Moreover, it was shown that the phosphorus content of these concentrates could be reduced from 0.25% to 0.03% phosphorus by acid leaching. A brief discussion on production costs based on current and future developments in iron ore processing is given.

Jan 1, 1983

The library of the above-named Societies is open from 9 A. M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90, 000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 7, 1918

Sec. 1. The membership of the Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that no member of any class whom residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the claw of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members.

Jan 1, 1941

By R. L. Wiegel

The National Science Foundation, Erie Mining Co., and University of Minnesota Mineral Resources Research Center jointly sponsored a project to demonstrate the use of a small computer in the control of cyclone overflow size on one line in the Erie Mining Co. concentrator. The Erie circuit, similar to most taconite circuits, uses magnetic separators to reject tailings following each stage of grinding, resulting in additional variations in the demands made on the grinding circuit because of weight rejection fluctuation. Mathematical models were developed for rod milling, ball milling, hydrocycloning, fine screening, and five stages of magnetic separation. These models were used in concert to simulate the operation of Erie's circuit from rod milling through finisher magnetic separation.

Jan 1, 1980

By Saburo Shigeno, Kunzo Amano

As shafts and tunnels move deeper levels in underground mining, development planning becomes more complex. The most serious problem is the aggravation of environmental conditions due to the imposition of higher-than-natural temperatures upon exposed strata. Since such a problem is a potential hazard to health, safety, and production, the authors have developed a system of computer-derived ambient-air temperature data for every major point of an underground mine under a given set of conditions. This system is comprised of two subsystems: 1) Ventilation network analysis, 2) Estimation of air - current temperature. The former is based on the Hiramatsu-Oka method, an improvement of the Scott-Hinsley method. The Hiramatsu-Oka method allows fast convergence and consideration of various fan characteristics. The latter subsystem considers heat radiation from strata, and the humidity. In several tests conducted at Besshi and Sazare Mines of Japan, the computer-derived data correlated with actual conditions.

Jan 1, 1969

By W. E. Anderson, T. M. Brady

As part of a larger study to identify factors influencing the practical operating life of wire rope used on large draglines in surface coal mining, field trips to operating surface coal mines were made during late 1975. Wire rope performance information was obtained from personnel at 13 mine sites west of the Appalachians. Seventeen pieces of equipment, utilizing bucket sizes ranging from 30 to 220 cu yd (23 to 168 m), were documented. Draglines at large US surface coal mines can be represented as 120 machines having 60-cu yd (46-m3) buckets, moving 1.8 x 10[9] cu yd (1.4 X 10[9] m3) of overburden during 6650 hours of productive availability per year. Based on the limited field study, the calculated downtime resulting from rope-related causes averages 105.6 hours per year for each typical 60-cu yd (43-m3) dragline. The total loss in production from this source alone is thereby estimated at about 25 X 10[6] cu yd (19 X 10[6] m3) annually.

Jan 11, 1979

By G. H. Walrod, J. M. Mutmansky, Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths, from 150 m to 300 m (500 ft to 1000 ft), and six different diameters, from 4.27 m to 7.32 m (14 ft to 24 ft), were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1979

By J. T. Price

The study was undertaken to investigate the effect in the charge to a blast furnace of zinc and alkali contents, which tend to form accretions and scaffolds in the upper sections of the furnace. Commercial iron oxide pellets were reduced in a CO:N2, 40:60 gas mixture in a 5-cm by 5-m counter-current reactor (Rist-type apparatus) designed to simulate blast-furnace conditions. Pellets from a commercial magnetite concentrate were prepared in the laboratory with zinc (1% ZnO) and alkali (1% KOH) additions to the concentrate. Reducibility, crushing strength and swelling tests were carried out and the results compared with test data from pellets prepared without additions. The results indicated normal behaviour for those pellets containing zinc, whereas those containing alkali swelled catastrophically under the same reducing conditions.

Jan 1, 1977

By Strathmore R. B. Cooke, Iwao Iwasaki, C. S. Chang

PYRRHOTITE has long been considered a gangue mineral to be eliminated as tailing in the treatment of various sulphide ores. However, in recent years the world-wide lack of sulphur resources has called attention to this mineral as a potential source of both sulphur and iron. Its importance as an economic mineral, however, has not been particularly emphasized. For this reason very little is known about its response to flotation, except that it can be depressed easily in alkaline circuit, by long aeration,1,2 addition of oxidizing agents3 or by starch.4 The object of this work was to study the floatability of pyrrhotite. This includes the effect of oxidation by aeration, of copper activation, and of change in pH.

Jan 2, 1954

By L. O. Howard

Much work has been done recently on the lead-antimony system' in connection with lead-rich alloys of commercial importance containing less than 20 per cent. antimony. Dean, Zickrick and Nix have called attention to the perpetuation in the literature of several erroneous data, such as a eutectic temperature of 228° C. at 12.5 per cent. antimony, instead of 247° at 13 per cent. The series is given as a classic example of a straight eutectiferous series in such late books as those of Heyn and Grossmann,2 Jeffries and Archer,3 Guillet and Portevin,4 Pulsifer,5 Rosenhain,6 and Liddell,7 as well as the somewhat earlier works of Hofman (1918), Wang (1909), and Williams (1920). The work of Dean has definitely shown a solid solution of antimony in lead at about 2.5 per cent. antimony. While lecturing to a class in general metallurgy at the University of Idaho, the writer had the students prepare a series of lead-antimony alloys for the purpose of illustrating methods of thermal analysis. Proper proportions of powdered antimony (sold as C.P.) and. test lead were mixed and melted in graphite crucibles under a reducing cover. Cooling

Jan 1, 1928

By Donald H. Yardley, A. Aly Selim

An economic simulation model was developed to predict the amount of copper recovered from copper oxide deposits, and the cost of producing it as a function of the deposit parameters. The economic simulation model includes programs for fragmentation design and cost, copper extraction, solution distribution and recovery, effluent solution cut-off grade, and financial analysis. Cost and price indices were also developed to evaluate the economic feasibility of in situ leaching operations as a function of their starting date. Application of the models to various hypothetical properties having the same area and different ore thickness shows that the effluent solution cut-off grade does not vary with the ore thickness nor with its grade. The percent of copper recovery is, however, shown to increase with the increase in the ore thickness and is independent of the ore grade. It is also shown that while the profit per unit of extracted copper increases with the increase in ore grade or ore thickness, the rate of return on total investment does not show any correlation.

Jan 1, 1979

By C. A. Hansen

INTRODUCTION It has been the experience of the writer, during some. five years' work with electrolytic zinc, that the zinc cell is perhaps more- sensitive to impurities in the electrolyte than the analytical methods as yet developed for the chemical identification and determination of these impurities; but that, when proper purification methods have been applied to a given solution, the behavior of the cell is quite independent of the original sources from which the zinc sulphate has been derived. It has also appeared that the behavior of the zinc cell is the best and surest check on the correctness and thoroughness of the purification methods used, because it indicates the presence of both current impurities. and cumulative impurities derived from the leaching of the ore; it also in

Jan 3, 1918

Carlisle: Jim Knapp, has been the good friend of hundreds-maybe thousands-of mining men in these western states in the last 40 or 50 years. Jim is going to talk about many of the mining camps of Nevada, where he has done plenty in the mining field during the last 50 years. Jim, for a starter, how did you happen to go to Nevada? Knapp: In the summer of 1902, two years after the discovery at Tonopah, the professor of mining at Stanford sent out myself and another student by the name of Joe Miller to make a report on the camp. We left San Francisco at 8 p.m., got to Reno the next morning, then took the train to Sodaville, arriving about 4:30 in the afternoon. The first man I met when I arrived at the Tonopah station was Tasker Oddie, a gentleman who later became the Govenor of the State and then a United States Senator. Before we got away from the stage station I also met S. H. Brady, the first mining engineer to put out his shingle in Tonopah. He afterwards became general manager of the West End Mining Co.

Jan 3, 1965

Rustenburg Platinum Mines, Ltd. is the largest producer of platinum metals in the western world. It is also the only major platinum producer this side of the Iron Curtain. One of its mines is situated at Rustenburg, 80 miles northwest of Johannesburg. It also has a smaller operation, the Union Section, 60 miles north of the Rustenburg property. Both mines exploit the Merensky Reef, which forms a part of the Transvaal's remarkable Bushveld Igneous Complex, an irregular oval area covering some 15,000 square miles. In order to cope with an increasing world demand for platinum and such platinum-group metals as palladium, rhodium, ruthenium, iridium and osmium, Rustenburg Platinum Mines embarked on a major expansion program some time ago. It is expected that production will reach an annual rate of 850,000 oz of platinum by the middle of 1969 and increase to 1 million oz by the middle of 1970. Capital expenditures at Rustenburg during the next few years will be about $60 million. It is believed that the ore at Rustenburg averages about 4.5 oz of precious metals per ton. About 70% of the metal is platinum, some 15% is palladium, and the rest is made up of the other metals in the platinum group.

Jan 4, 1969

By S. C. Riemer, I. Iwasaki, J. N. Orlich

The effects of percent solids, mill loading, and grinding time on product size distribution and ball wear were studied in a laboratory ball mill for a taconite ore. Mild steel balls and HCLA steel balls were used to examine the role that ball hardness play in grinding. Net production of - 44-µm (- 325-mesh) material reached maximum at 70% solids, whereas the ball wear decreased as pulp density increased. HCLA steel balls ground the taconite ore finer than mild steel balls under otherwise identical conditions. Examination of ball surfaces with a scanning electron microscope suggested that corrosive wear was mini- mal under nitrogen flushing conditions, and that grinding with mild steel balls involved nipping rather than attrition, whereas grinding with harder HCLA balls involved both nipping and attrition. Pulp viscosity controlled the thickness of pulp layer on balls, thereby affecting grinding efficiency and ball wear.

Jan 1, 1986

SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain Members.

Jan 1, 1946

By P. F. Ahner, Leonidas Petrakis, Fred E. Kiviat

High gradient magnetic separations (HGMS) is a recently developed technique in which magnetic micron-size particles contained in a flowing fluid medium can be extracted from that medium. HGMS is presently utilized on a commercial scale in the kaolin processing and steel industries, and is being investigated for solid-liquid separations in numerous other processes. The performance characteristics of HGMS in the kaolin and steel industries are briefly summarized. A discussion of HGMS performance with respect to solids removal in a coal liquefaction process is presented to illustrate its applicability to difficult solid-liquid separations. Here, the properties of the solids suspended in the liquified coal are such that the HGMS separator achieves over 90% solids removal. The optimization of the HGMS operating parameters to yield these results will be discussed. To further illustrate the potential of HGMS, its performance with respect to the removal of oil and solids (over 98% removal) from a petroleum refinery process water effluent stream will be briefly considered.

Jan 1, 1980

By David D. Rabb

Under the auspices of the Atomic Energy Commission, the Lawrence Radiation Laboratory of the University of California analyzed an experiment to provide information as to whether the chimney of broken rock produced by a deeply buried nuclear explosive could be "drawn" by conventional techniques. Since many low-grade disseminated ore-bodies occur in a granite media, the experiment took place in a granodiorite-quartz monzonite intrusive porphyry in the Nevada Test Site as a follow-up to the Department of Defense's Hardhat detonation in February 1962. For emplacement of the nuclear device, a 12 ¼ - in. pilot hole was reamed to a diameter of 44 in. and a depth of 950 ft in one pass using a Hughes multiple-cluster rotary bit. It was then cased to 36 in. ID. The center of the explosive device was located 938.85 ft below the collar. The yield of the device was predicted to be 5 kilotons, or an equivalent of 5000 tons of TNT; the yield was later confirmed by chemical means to be 5.4 kilotons.

Jan 3, 1964