Search Documents

By Klaus Schwerdtfeger

The rate of formation of silicon monoxide from silica spheres has been measured at 1500°C in H2, H2-H2O, H2-He, H2-Ar, and CO-CO2 gas mixtures. Indications are that in the hydrogen-containing gases the reaction rate is mainly determined by convective diffz~sion. In the CO-CO2 mixtures the rate approches a constant value which is independent of sphere diometer (and gas velocity). This suggests that a surface reaction becomes rate controlling in CO-CO2 gas. WHENEVER silica is exposed at elevated temperature to a strongly reducing atmosphere there occurs, inevitably, a volatilization of silica by the formation of gaseous silicon monoxide. Because of the importance of this reaction in metallurgical processes and laboratory experiments, its kinetics were studied in the present work. EXPERIMENTAL The spheres made of vitreous silica were suspended by a molybdenum wire in the hot zone of a gas-tight high-purity recrystallized alumina furnace tube of 3.1 cm internal diam and 100 cm length. Molybdenum wire resistance heating was used. A purified H2, H2-H2O, H2-He, H2-Ar, or CO-CO2 gas mixture was passed through the tube, from top to bottom. The amount of silicon monoxide formed was determined by weighing the silica balls before and after the experiments. The silica balls were made from commercially available translucent fused quartz glass. In experiments with hydrogen-containing gases the silica stayed vitreous during the experiment, whereas in experiments with CO-CO2 mixtures, which were performed over longer times, the balls were always crystallized to cristobalite (as determined by X-ray examination) at the surface. Constant-pressure head capillary flowmeters were used to control the composition of H2-He, H2-Ar, and CO-CO2 gas mixtures. The oxygen and water vapor were removed from the gases containing hydrogen by passage through columns containing platinized asbestos (450°C) and an-hydrone. The CO was purified from O2 and CO2 by passing it through activated copper (200°C) and through ascarite. The H2-H2O gas mixtures were prepared by passing purified Hz through a mixture of oxalic acid dihydrate and anhydrous oxalic acid held at a constant temperature in a water bath. The equilibrium water vapor pressures of oxalic acid dihydrate-anhydrous oxalic acid mixtures were taken from the available data.1 The furnace system was checked for sufficient gas tightness at regular intervals. As an additional check, the H2O and CO2 contents were measured in the exit gas and were found to agree closely with the metered contents when H2-H2O or CO-CO2 mixtures were used. When purified H2 was used, H2O pressures found in the exit gas were always below 0.1 mm Hg. These contents originate either from an incomplete reoxidation of silicon monoxide in the cold part of the furnace or from small leaks which cannot be avoided. If the latter is the case, such small uncontrolled H2O contents decrease the partial pressure of SiO in equilibrium with SiO2 by less than about 7 pct, which is considered small in comparison to other experimental uncertainties. The temperature of the furnace was controlled automatically in the usual manner. The reported temperature was measured with a Pl-Pt/l0pct Rh thermocouple and was accurate to ± 5°C. TRANSPORT-CONTROL LED RATE OF REDUCTION The gaseous convective diffusion from the surface of a sphere can be predicted from the semiempirical relationship obtained by Ranz and Marshall2 in a study of the evaporation of water and benzene drops in air. The following equation applies:

Jan 1, 1967

By Charles B. Dudley

THEO. N. ELY, Esq., Superintendent of Motive Power. DEAR SIR: It is now nearly three years since my first report to you on the subject of steel rails was written. That report, as you will remember, dealt principally with the question of the relation between the chemical composition and physical properties of steel rails and their power to resist crushing and fracture in actual service. Other matters were referred to or touched upon in that report, but the main question was, Why do some rails crush or break in service while others do not? You will doubtless remember that the principal conclusion arrived at was, that the softer rails are less liable to crush or break in service than the hard ones. Or, in other words, so far as conclusions could be drawn from the chemical analysis and physical test of 25 samples of steel rails which had actually been in service, these conclusions were that those rails which have the smaller amounts of carbon, phosphorus, silicon, and manganese are less liable to crush or break in service than those which have larger amounts of these elements. Or, again, looked at in the light * At the Lake George meeting of the Institute in October, 1878, I had the honor of presenting to the Institute, through the kind permission of the officers of. the Pennsylvania Railroad Company, the results of a study of twenty-five samples of steel rails, which had all been in actual service. Considerable discussion followed the publication of that paper, and there seemed to be a strong disinclination, especially on the part of the steel-rail manufacturers, to accept the conclusions presented. One of the principal objections urged against the conclusions drawn was, that they were based on too few samples; in other words, that no conclusions safe to act upon could be drawn from the examination of twenty-five rails. In view of this criticism it was decided to repeat the investigation with a larger number of samples, and with the aid of the experience gained in the first investigation. The results of this second study of steel rails are, by the permission of the officers of 'the Pennsylvania. Railroad Company, herewith presented to the Institute, with the sincere desire that they may aid in adding to our knowledge of this most important product. Like the previous paper, this is in the form of a report to one of the officers of the company, which will account for the style, and the manner of presenting the data

Jan 1, 1881

By G. Nabi, W-K. Lu

Cylindrical specimens of natural dense hematite were reduced to magnetite at atmospheric pressure in H2-H2O mixtures of known composition over the temperature range 1084° to 1284°K. The rate of reduction was measured by the rate of movement of the interface between hematite and magnetite. The diffusion of gases through the gaseous boundary layer, the magnetite layer, and the interfacial chemical reaction were all considered in the interpretation of experimental data. The mass transfer coefficient through the boundary layer was calculated using accepted correlations. Values of the chemical reaction rate constant and the diffusivity of hydrogen in the magnetite phase were determined. THE present investigation is concerned with the reduction kinetics of natural hematite to magnetite by H2-H2O mixtures in the temperature range 1084" to 1284°K at atmospheric pressure. This reaction is the first step in the series of topochemical reactions in the process of reducing hematite to iron. Kinetic information of the simple steps such as hematite-magnetite transformation is necessary in order to have a better understanding of the complex processes of hematite reduction in iron-making. It also has direct industrial significance because magnetic roasting is one of the most important methods in benefication of lean ore.&apos; Although many technical papers have been published on the process of magnetic roasting and iron oxide reduction, very little information is available in the literature concerning the fundamental nature of hematite reduction to magnetite by reducing gases. Hansen et al.2 reduced the dense synthetic pellets of high-purity oxide in CO-CO2 mixtures and determined the reaction rate by weight-loss method. They were able to interpret most of their results by applying the interfacial area control theory developed by Mckewan.3 In contrast, Wilhelm and St. Pierre,4 who studied reduction of hematite to magnetite in H2-H2O mixtures by weight-loss method, stressed that the resistance of the porous magnetite layer to the diffusion of gases cannot be neglected in consideration of the overall reaction rate. In the present study the contributions of interfacial chemical reaction, diffusion of gases through the magnetite phase, and the gaseous boundary layer to the overall reaction rate will be considered. APPARATUS AND PROCEDURE Hematite Specimens Preparation. Natural hematite ore from Vermillon range of Northern Minnesota was selected for the present investigation because of its high purity and thermal stability. Chemical analysis of five samples gave the following average values: 67.52 pct total iron (96.62 pct Fe2O3, 0.28 pct FeO, 0.03 pct metallic iron), 2.53 pct SiO2, <0.07 pct MgO, 0.03 pct CaO, 0.05 pct combined mixture, 0.07 pct loss on ignition, and 0.34 pct other. Cylindrical specimens of 0.93 cm in diam and 2.7 cm in length were drilled from slabs of ore with a water-cooled diamond core drill. These specimens were heated to 1000°C and furnace-cooled. Specimens with silica pockets developed large cracks. The uncracked specimens were heated a second time, and their surfaces were carefully examined with a microscope. Those with hairline cracks or surface inhomoaenitv-- were rejected. Preparation of H2-H2O Mixtures. H2-H2O mixtures were prepared by the combustion of H2-O2, mixtures in a pyrex glass chamber in the presence of a catalyst. Alumina pellets coated with palladium, supplied by Englehard Industries, were used as the catalyst. Purified grades of hydrogen and oxygen were used which were repurified by usual techniques. Hydrogen before entering the combustion chamber was passed through an activated alumina H2O absorption bulb, with copper turning at the top. The cover of this bulb was not made pressure-tight so that any pressure development in the hydrogen line would cause the cover to blow off and also the copper turnings would act as a flame arrester in the case of a flashback from the combustion flame. Oxygen flow rates were measured with a bubble flow meter after purification with 1 pct accuracy. Hydrogen flow rates were measured by "precision wet test meter" and the amount of unburnt hydrogen was accurately measured by a bubble flow meter, after condensing water vapor in the gaseous stream. The Pyrex glass bulb contained concentric Vycor glass tubes as shown in Fig. 1. Oxygen was prevented from diffusing into the hydrogen line by threading platinum wire through pores at the combustion end of gas inlet tube. The glass bulb was heated with a Kanthal heating wire pasted in asbestos paper. The surface temperature of the bulb was measured with a thermocouple and adjusted to remain at approximately 350°C. The gaseous reaction chamber also served as a preheater for gases to avoid thermal segregation. The following sequence of operation was adopted. 1) Nitrogen was passed through the outer concentric tube to purge the catalyst bulb of oxygen. 2) Hydrogen was introduced through the inner tube until a steady flow was obtained. 3) Oxygen was then introduced into the nitrogen stream passing through the outer tube. 4) When combustion had commenced and a flame was visible over the platinum wire, the N2 was turned off.

Jan 1, 1969

By Lyman Johnson

Single crystals qf copper in "single slip" orientatiorzs have been deformed in compression. During defortnation all of the independent deformation parameters have been measured. These parameters consist of thefive strain components and three components descrihing the lattice rotation. By a finite strain analysis these pararmeters , forrming a deformation gradient martrix, are related to the amounts of slip on each of the twelve slip systems. The results show that the amount of secondary slip is about equal to the amount of primary slip. This is an order of magnitude larger than has been believed previoutsly. ACCORDING to early theory and experiments, when a single crystal of a fcc metal is deformed in tension or compression it should deform by slip on only one slip system until the stress axis reaches a symmetrical orientation.&apos; However. the observation of a large increase in the secondary dislocation density during ..single slip" makes it clear that some slip does occur on secondary systems. Knowledge of the amount and distribution of this secondary slip is essential to a complete understanding of the mechanisms of single-crystal deformation. Ahlers and Haasen 2 and Mitchell and Thornton1 have tried to detect the amount of secondary slip in single crystals of silver and copper, respectively. Each simultaneously measured the angle A, between the tensile axis and the primary slip direction and the length 1 of a gage section of the specimen after incremental amounts of deformation in tension. The measured A, was then compared with the theoretical single slip angle hp. given by sin Ap = j sin . hO where ?o was the initial angle between the tensile axis and the primary slip direction and lo was the initial gage length. In both sets of experiments a small but systematic difference between ?e and ?p was found. This difference must be due to the occurrence of secondary slip. However, as Mitchell and Thornton1 pointed out. nothing quantitative can be said about the amount and distribution of this secondary slip from the measurements that they made. The reason that no quantitative conclusions could be made is because no unique solution for the distribution of slip on the twelve fcc slip systems can be determined from only two measured deformation parameters such as A and 1. There are, in fact, eight independent macroscopic deformation parameters that can be measured when a single crystal undergoes a homogeneous deformation. Physically these can be thought of as the five finite strain components and the three angles describing the crystal lattice rotation. All eight of these parameters were measured by Taylor4,5 for aluminum deformed in tension and compression. At that time the concern was to show that slip occurs on {111 (110) systems in fcc metals, and the mathematics were not available to determine what slip distributions were compatible with the measurements. In this paper the mathematics6,7 are developed that allow the slip distribution to be determined from these measurable macroscopic deformation parameters. The analysis is applied to the measurements of the strain and lattice rotation of copper single crystals deformed in compression. The results show that the amount of secondary slip is an order of magnitude larger than had previously been thought. CRYSTALLOGRAPHIC DESCRIPTION OF A HOMOGENEOUS DEFORMATION The deformation of a solid body can be represented by a transformation matrix F that transforms the un-deformed state into the deformed state. Consider a vector X connecting two material points in the unde-formed material and the vector x connecting the same two material points after deformation, where both vectors are referred to the same set of Cartesian axes. The final vector x is related to the initial vector X by the equation: X = FS. [2] Eq. [2] can be considered as the equation defining F, which is called the deformation gradient matrix. Its components are: If the deformation is homogeneous, the transformation is linear and the components of F are constants. Using subscript notation, if P is the unit vector in the initial direction of a material line, the components of the unit vector p in the direction of the same material line after deformation are given by:

Jan 1, 1970

By R. W. Raymond

HAVING had recently the opportunity of examining a transit and a plummet-lamp, manufactured by Messrs. Heller & Brightly, of Philadelphia, and intended for the use of mining engineers in under-

Jan 1, 1873

By R. W. Raymond

HAVING had recently the opportunity of examining a transit and a plummet-lamp, manufactured by Messrs. Heller & Brightly, of Philadelphia, and intended for the use of mining engineers in under

By Gerard Matthes

Only in recent years has any practical headway been made in the application of aerial photography to geological problems, and up to the present time its principal value to the geologist and mining engineer has been in "areal geology;" i. e., the study of formations as revealed at the surface. The object of this paper is to set forth briefly the principal advantages that may be derived from aerial photographic data in geological work and to serve in a measure as a guide to those who may be contemplating its use. Geophysical prospecting has for object the locating of mineral under the surface. Inasmuch as the geologist&apos;s chief complaint in life is a dual one—inability to see under the surface and inability to visualize comprehensively what he does see on top of the ground—geophysical prospecting coupled with aerial photography should do much to lessen his burdens. To what extent aerial photography can be made a useful adjunct to geophysical prospecting remains to be proved, but the inference drawn here is that it holds many alluring possibilities. To avoid disappointments, it should be stated at the outset that to the geologist or mining engineer an aerial photograph or mosaic is only a tool, the efficient use of which he must set out to master. Upon his skill and ingenuity in applying it to particular problems will depend largely the value of the results that he will obtain. Under the most favorable conditions an aerial mosaic, or even a few loose photographs, because of the exceptionally comprehensive oversight which they afford of field data, such as dips and strike observations at isolated outcrops, local indications of faulting, mineral and fossil finds, greatly facilitate study and correlation, save much tedious foot work, and may repay their cost many times. Even so, types of country may be found where the most skillful use of the best of pictures will produce results so meager as to render the cost of aerial photography entirely unwarranted. Between these two extremes will be found endless variations and possibilities. Hence no set rules can be promulgated. The safest procedure is to treat each case as a separate problem and to carefully weigh the relative advantages and shortcomings of aerial photography before embarking on its use.

Jan 1, 1928

By James A. Brierley, Corale L. Brierley

Microorganisms have been considered as agents which may be of importance in catalyzing hydrometallurgical processes for the extraction of metals from low-grade ore minerals. Various microorganisms and their role in bacterial leaching are described. Bacterial leaching as applied to copper, uranium, zinc, lead, and coal is discussed.

Jan 1, 1981

By G. S. Rice

Undoubtedly there is a serious problem through the juxtapostion of gas and oil wells and coal mines, not only at the present time, but possibly of far more serious import for the future.

Jan 1, 1915

By Rossiter W. Raymond

(Read at the Wilkes-Barre Meeting, May, 1877.) THE 12th of April, 1877, witnessed the celebration, at Freiberg, Saxony, of an event profoundly important for the ancient mining industry of that district, and full of interest to mining engineers throughout the world-namely, the connection of the famous Roth-

Jan 1, 1878

By R. E. Zimmerman, Shiou-Chuan Sun

An evaluation of the mechanism surrounding the froth flotation of coarse coal and mineral particles as a result of experiments conducted at The Pennsylvania State College. Maximum size ranges for both bituminous and anthracite coals were established as well as the factors affecting the floating of coarse particles.

Jan 5, 1950

By C. G. Rhodes

A technique for producing etch pits in uranium monocarbide has been developed. The pits, which are assumed to be associated with dislocations, appear individually and as arrays delineating sub-boundaries, as seen in Fig. 1. The samples used were single crystals prepared by the technique described by Nadler.* Uranium

Jan 1, 1963

By E. A. Sondreal, F. I. Honea

This paper summarizes coal and ash properties and pilot-plant results for 14 key lignite seams in the Gulf Province, as well as discusses operating problems encountered by the four Texas power plants burning Gulf Province lignite. Some consideration is given to the design of future power plants.

Jan 1, 1982

By Y. P. Chugh, R. A. Missavage

Moisture has been known to influence strata failures in coal mines for a long the. A concise review of what is known about effects of moisture on strata control with emphasis on the Illinois basin coal mines is presented in this paper. Some approaches to mitigate the effects of moisture-leaving coal in the roof, guniting, shotcreting, application of sealants-are then briefly discussed.

Jan 1, 1982

By F. D. Dietiker

After determination of the requirements for a given application, proper selection of a belt conveyor is made from tables and formulas commonly used by conveyor designers. Belt conveyors, which are universally accepted as a means of transporting bulk materials, also perform the important functions of stockpiling and reclaiming.

Jan 1, 1978

By F. W. Bloecher, A. M. Gaudin

Using an adsorption-column technique the partition of dodecylamine between quartz and water has been determined at concentrations ranging from 0.5 to 4000 mg per liter. The adsorption varies as the square root of the concentration. Attachment of dodecylamine to quartz is reversible. The amount adsorbed in a flotation operation giving almost complete recovery is under 5 pct of the amount required for a monolayer.

Jan 4, 1950

By S. G. Lasky

Abraham Lincoln is reputed to have said that if you want to chart a course to some destination, you have to know where you are starting from. In this instance we have to define our starting point in a double manner: 1) What was the theoretical basis of the Paley predictions? 2) What actually did the Commission predict, so that we can see how the predictions have worked out up to now as a basis for considering how they may have to be changed.

Jan 3, 1960

By Z. Moser, W. Ptak

The experiments were carried out by the method of measuring the electromotive force of concentration cells having zinc as a reference electrode, the second electrode being the liquid alloy Zn-Sn-Cd-Pb. The electrolyte consisted of liquid chlorides and had zinc ions. The measurements were made for seventy -five alloys of different mole fractions within the temperature range of 714° to 877°K. The experimental results enabled the calculation of the activity of zinc in tested solutions. The activities of zinc were calculated by means of Krupkowski&apos;s formulas.3 In addition, the formulas for coefficients of activity of zinc, tin, cadmium. and lead as the function of composition and temperature were given. Activity of zinc was compared with the values obtained from experimental results, and good agreement has been observed. On this basis it can be stated that the theoretical formulas are suitable for determining the thermodynamic properties of liquid quaternary metal solutions. IN the metallurgical processes being carried out at present multicomponent liquid metal solutions take part. For the thermodynamic analysis of these processes it is necessary to know the thermodynamic properties of these solutions. Therefore, many experimental and theoretical papers deal with this problem. The theoretical papers are generally based on the assumption that the structure of liquid metals is similar to their structure in the solid state. In this manner the model of liquid solution, consequently described by means of statistical thermodynamics, has been accepted. This method is being lately developed, especially for solid solutions. Statistical thermodynamics was applied among others by Guggenheim 1 for describing the thermodynamic properties. Unfortunately, the formulas of statistical thermodynamics are often not suitable for the interpretation of experimental results. Attention should be drawn to the relations obtained by means of formulas of phenomenological thermodynamics which always have constants derived with the aid of experimental methods. In the case of the multi-component solutions which contain some additions of impurities besides the basic metal, wagner2 introduced interaction parameters. Equations for the relationship between the activity coefficients and composition were also given by Krupkowski." he application of these formulas requires a good knowledge of the thermodynamic properties of the corresponding binary systems. In these formulas, as in Wagner&apos;s, there appear constants which should be determined from ex- perimental data. Nowadays, different experimental methods are applied for evaluating the thermodynamic functions of solutions, for instance: vapor pressure measurements, calorimetric methods, and the measurements of electromotive force of concentration cells. In the present paper this last method for evaluating the thermodynamic properties of four-component systems, Zn-Sn-Cd-Pb, was applied. For instance in the case of Zn-Sn solutions Alabyshev and Landratov, 4 Fiorani and Valenti, 5 and ptak6 performed the investigations. The Zn-Pb system was worked out by Kleppa 7 and Cd-Pb and Cd-Sn by Elliot and chipman.&apos; This method was also applied for determining the activity of zinc in ternary solutions. 1) EXPERIMENTAL METHOD The experimental arrangement with detailed description is given in Fig. 1. It consists of resistance furnaces, one serving for melting samples and the other containing the flat-bottomed, measuring quartz tube with the liquid electrolyte. Liquid metals and alloys are in glass supremax tubes, which have an opening in their lower part above the metal level. This opening allows the filling of the tubes by the electrolyte. In these tubes tungsten wires are placed which by means of suitable conductors are connected with a potentiometer. It is assumed that tungsten dissolves Fig. 1—Schematic diagram of the experimental arrangement for the investigation of the thermodynamic properties of liquid metal solutions: 1, resistance furnaces; 2, autotransfor-mers; 3, galvanometers; 4, regulator of temperature; 5, gas purifier with concentrated H2SOP; 6, U-tube with P2O5; 7, thermostats; 8, steel block for thermostating; 9, supremax tubes for alloys; 10, tungsten electrodes; 11, inlet and outlet of argon; 12, measuring quartz tube; 13, tube for melting samples; 14, tube for thermocouple; 15, cover of quartz tube; 16, rubber seal; 17, bottom cover; 18, outlet of electrodes to potentiometer; 19, outlet of thermocouples to potentiometer; 20, upper view of the quartz tube cover; 21, orifices for cover screws; 22, orifice for argon inlet; 23, orifice for thermocouple; 24, orifices for tubes containing liquid metals; 25, inlet for water-cooling system.

Jan 1, 1969

By J. Lewis, J. Harper, M. F. Ashby

A grain boundary in a metal interacts with second-phase particles, which exert a pinning force (first estimated by Zener) on the boundary opposing its motion. We have computed the shape of boundaries which interact with more or less spherical second-phase particles and have constructed a soap-film model to reproduce the shape of the boundary surface. An important result is that measurement of this shape allows the pressure, or driving force, on the boundary to be measured. We hare applied this technique to grain boundaries in two alloys and hate measured the pinning force exerted by single second-phase jwrticles on the boundaries. It is in good agreement with Zener&apos;s estimate. J\. boundary between two grains, or two bulk phases, interacts with small inclusions or particles of a second phase, whether they are gas or solid. This interaction means that the boundary, forced to migrate by a difference in free energy between the material of the two grains or phases which it separates, exerts a force on a particle which it touches, tending to drag it forward. (The movement of inclusions through metals under the influence of this force, has, in fact, been observed. 1-3) Equally, the particle can be thought of as exerting a pinning force on the boundary, tending to hold it back. Zener (in a celebrated private communication4) first realized that this interaction, and the resulting pinning force, existed. His calculation of its magnitude was crude but adequate: a spherical inclusion of radius r blanks off an area nr2 of the boundary on which it sits; since the boundary has an energy of rMM x per unit area, the blanlung-olf decreases the energy of the system by MM: this energy is returned to the system if the boundary is pulled free from the inclusion— a forward movement of the boundary by a distance r will do this—so that the maximum pinning force is Trrym.M- A similar argument can be made for inter-phase boundaries. The nature of the particle itself did not enter this, or two subsequent treatments.5,6 When it is considered, tic leifthe energyoftheb a) The boundary may enter and pass through the particle if the energy of the boundary is lower within the particle than in the matrix. Fig. l(r/). Certain coherent precipitate particles behave like this. h) More usually, the boundary will bend round the particle, enveloping and bypassing it. Fig. l(b). In doing so, it changes the structure and energy of the interface between the particle and its matrix. This means that the boundary does not touch the particle surface at right angles, as early treatments assumed,5&apos;9 but at some angle a which depends on this change in surface energy of the particle, and can be calculated from the equilibrium of surface tensions. Most precipitate particles and inclusions behave like this. Gas bubbles or liquid drops can be regarded as belonging to either group. The progress of bypassing is conveniently measured by the angle shown in Fig. 1. When the nature of the particle is ignored, its maximum pinning force is exerted when - 45 deg. When it is considered, this critical value of is found to depend on a and thus on the nature of the particle. The maximum pinning force lies between nryMM and 2jtjMM (Appendix 1). not very different from Zener&apos;s result. In reality, a boundary between crystals has a specific energy and tension which varies with the orientation of the boundary. Furthermore, recent experiments7 indicate that such a boundary is not atom-ically smooth, but has steps on it: migration of the boundary corresponds to the sweeping of these steps across the boundary surface, like the Frank model of crystal growth from the vapor. This means that the interaction of a boundary with particles should really be considered in terms of the way in which particles hinder the movement of these steps. To suppose a grain boundary or interphase boundary to be smooth, and to ignore the variation of its energy with orientation, is to liken it to a soap film. The advantage of this soap film approximation, which we have used throughout this paper, is that interaction energies and boundary shapes can be calculated easily. We have done this by numerical computation and by using a soap film model, and have compared the results with grain boundaries in an aluminum-based and a copper-based alloy. It turns out that the shape of the boundary which bulges between particles allows the pressure an it to be calculated; that is, the local driving force an the boundary can be measured. This has allowed us to check the Zener relationship experimentally.

Jan 1, 1970

By Martin C. Kuhn, Lawrence G. Stevens, J. Mark Richardson

The majority of the world&apos;s known and anticipated reserves of nickel ores are lateritic deposits At present, there are several different process alternatives for recovering nickel and other desired metal values from laterite ores An overview is given of the selective reduction roast/ammoniacal leach process, one of the processes in commercial operation.

Jan 1, 1981