Search Documents

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be .of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or, personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will. use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 9, 1914

By Richard Maclin Stewart

A priest at Shenandoah, Pa., one day persuaded the president of the Philadelphia & Reading Coal & Iron Co. to slush breaker waste and culm into old mine workings in order to save his church from being destroyed by surface subsidence. The year was 1864, the project was successful, and history recorded the first use of hydraulic backfilling. Shortly afterward, the method was applied to several eastern coal mines for area fill to control subsidence. In 1884, hydraulic backfilling was used to control a mine fire in the Schuylkill region of Pennsylvania. The idea was taken to Europe by German engineers and developed successfully at the Myslovitz colliery in Upper Silesia in 1901. From there it was applied to several mines throughout Europe.

Jan 4, 1958

By Alexandre Mussard

How do you make a mine out of 500 000 kg (1.1 million lb) of uranium oxide contained in a low-grade deposit with high clay content? Confronted with these limited reserves and mineralogical problems at France's St. Pierre du Cantal uranium deposit, engineers adopted a rather unusual mill process to keep capital costs to a minimum. Crushing and grinding were eliminated by using a high pressure monitor to slurry ore directly from stockpiles. After mechanical separation of the high-grade fines from low-grade sand, the sand fraction is washed of clay to increase permeability and then it is heap leached. Fines are sent to agitated vessels for acid leaching, and the pulp from this operation is diluted by pregnant solution from the heap leaching.

Jan 10, 1979

By James C. Fisher

Traditional uranium exploration techniques were utilized and comparatively evaluated in the Front Range, Colorado uranium province. Intense surficial leaching and thick colluvial cover render traditional airborne and ground radioactivity reconnaissance prospecting useless. Radon gas emanometry and sulfur gas emanometry were slightly more effective but the long and short term variations In soil gas emanation rates make it extremely difficult to gain useful information from these systems. The technique judged most useful was Track Etch radon prospecting. The excellent definition of the technique, as well as its repeatability, indicate that it is an ideal prospecting tool for narrow vein-type deposits similar to those of the Front Range, Colorado.

Jan 1, 1976

By E. T. Turkdogan

The activities of SiO2, FeO, and Fe2O3 are calculated from previous experimental data on the activity of oxygen in Fe-Si-O melts at 1550°C. Using the oxide-activity data, the free energy of formation of fayalite from its oxides is evaluated for 1550°C. A number of investigators1-4 contributed to the study of the state of oxidation of iron in SiO,-FeO-Fe,O3 melts and the phase equilibria in the system Fe-Si-O. In a more detailed study, Schuhmann and Ensio5 and Michal and Schuhmann% easured the state of equilibrium in the SiO,-FeO-Fe,O3 melts saturated with y-iron or silica or both under low-oxygen potentials and within the temperature range 1250" to 1350°C. Similar measurements were also made by Turkdogan and Bills7,' over wide ranges of composition and oxygen potentials at 1550"C. Using the experimental data on the oxygen activities in the ternary system, Schuhmann' calculated the activities of silica and ferrous oxide in Si0,-FeO-Fe2O3 melts for 1350°C. Adequate knowledge on the activities of the constituent oxides of melts is essential in the study of reaction-equilibria and reaction-kinetics in oxide-melts. With this in view, the activities of oxides in SiO2-FeO-Fe2O3 melts at 1550°C are computed using the experimental data of Turkdogan and Bills7'8 on the oxygen activities in these melts.

Jan 1, 1962

By C. Dinis da Gama

In mining, all unit operations are closely interrelated, and the results of blasting are probably the key factor within that sequence. The drilling program prior to blasting is just as dependent upon the desired rock fragmentation as are the loading, hauling, and mechanical crushing operations which are economically and technically influenced by the results of blasting, namely, the size and scatter of the product. What is known today as optimum blasting is the process of designing a blast in order to obtain a certain degree of fragmentation so that overall mining costs are minimized. Applying this criterion often results in a different program than when an individual blasting pattern is chosen only on the basis of the lowest operational cost for that pattern, disregarding what comes before or after the blast. [Fig. 1] shows the characteristic variation of mining unit costs with the degree of fragmentation, or the maximum size of blocks obtained from blasting. From the figure, it can be seen that optimum breakage must correspond to the lowest total costs, but reducing drilling-blasting costs only does not achieve such an optimum solution. Methods of designing surface or underground blasting operations should comply with the optimization criterion, but this compliance is feasible only if a detailed mining system analysis is available. Therefore, predictions of costs of loading, transporting, and mechanical breakage of ore as a function of its size will define a narrow range of variation for drilling and blasting parameters in order to get the minimum total costs.

Jan 1, 1972

By Robert L. Bates

An industrial mineral, says the Glossary of Geologic Terms, is "any rock, mineral, or other naturally occurring substance of economic value, exclusive of metallic ores, mineral fuels, and gemstones; one of the nonmetallics." Probably most geologists and engineers would accept this simple and straightforward definition, at least as a general statement. On analysis, however, certain anomalies crop up. For example, it may be considered arbitrary to include industrial diamond and corundum, but to exclude their precious varieties, gem diamond and sapphire. So the present volume has a section on gems and gem materials, in spite of the definition. Another problem arises when we try to define precisely what is metallic and what is nonmetallic. Bauxite and ilmenite certainly qualify as metallic ores, but both are also raw materials of important nonmetallic substances; hence they are included in the book. A third anomaly is that, by common consent of geologists, engineers, mineral economists, and others concerned, the term industrial minerals may include not only rocks and minerals but also certain manufactured products like cement and lime, and even mixed groups of natural and artificial products, such as abrasives and refractories. Thus the central realm of the industrial minerals is clear enough, but its boundaries tend to be indefinable. Since a definition that allowed for every irregularity in the outer fringes would be excessively un- wieldy, the one quoted above may be considered satisfactory. The expression industrial minerals is commonly equated with nonmetallics, and with the somewhat more precise phrase industrial minerals and rocks as in the title of this book.

Jan 1, 1975

By R. Lingle, E. Hardin, M. Board, H. Pratt, W. Ubbes, M. Voegele, N. Barton

A 2 m. cube of jointed, Pre Cambrian biotite gneiss was subjected to uniaxial and biaxial loading at ambient and elevated temperature. The effects of different boundary conditions on the following rockmass properties were investigated: deformation modulus, joint stiffness, dynamic modulus, coefficient of thermal expansion, thermal diffusivity and conductivity, and joint permeability. Test conditions ranged between 0 and 6.9 MPa uniaxial and biaxial load, and 12° to 74°C mean block temperature. The tests were performed as part of the Office of Nuclear Waste Isolation program for evaluating site charterization test methods for measuring the hydro-thermal-mechanical properties of rock masses. The fracture flow experiments discussed in this paper were described in detail in a similar paper given to this symposium in 1981 (Voegele, 1981). DEFORMATION MODULUS Horizontal deformation measurements oriented parallel to the loading direction were made at the block surface. Several instrument types were employed: surface short-rod extensometers, bonded strain gauges, vibrating wire strain gauges and the Whittemore caliper strain gauge. Two vertical and two slant borehole extensometers measured vertical displacement. Loading history, especially during uniaxial loading, was critical to interpretation of observed deformation and fracture flow data. This important tendency has been observed in other large-scale laboratory (Bandis, 1980) and field tests (Pratt, et al., 1977). Excavation of the block resulted in minimal disturbance to the intrinsic condition of the sample. Even so, permanent, unrecovered "set" was imparted to the block beginning with the first low-stress biaxial load cycle to 3.45 MPa (Table 1). Unloading

Jan 1, 1982

By David W. Pasho

The success of a collector vehicle, designed to recover manganese nodules under the conditions which exist in deep ocean mine sites will in part be determined by the effectiveness of pick-up and running gear mechanisms. For the purpose of qualitative comparison, some specific aspects of seafloor interactions with various concepts are reviewed utilizing existing data on seafloor characteristics and running gear/tool interaction with soils.

Jan 1, 1976

By W. J. Nelson, R. B. Nance

Detailed underground geologic mapping at a scale of 1:1200 has been carried out at the Crown II Mine of Freeman United Coal Mining Co., which operates in the Herrin (No. 6) Coal Member. The roof sequence, upward from the coal, includes (1) soft, medium -to dark-gray shale; (2) hard, black, fissile shale; (3) argillaceous nodular- bedded limestone, and (4) fine-pined, shaly, water-bearing sandstone. The first unit is highly lenticular, and any or all may be missing at a given locality. The sandstone has a sheet facies and a channel facies. The Herrin Coal is eroded in channels near the Crown II Mine. Structural features mapped at Crown II include normal and strike-slip faults and limestone "bosses." Less stable roof and wet conditions are encountered where the limestone is thin or missing or where it is broken by natural fractures or by artificial openings that intersect the water-bearing strata above the limestone. Geologic mapping of the underground workings has allowed us to predict faults, fracture zones, and channels ahead of the face for this mine. Some lithologic and structural pattern apparently are random and cannot now be projected. Conventional exploratory drilling is entirely inadequate to map faults or lithology of the roof, but it does indicate the range of lithologic variability, which can be used to project needs for roof supports. Drilling also is useful in locating channels and in mapping regional variation in thickness and facies of the sandstone.

Jan 1, 1983

By M. Bourgon

The conductivity of liquid copper sulfide has been measured as a function of the mole fraction of sulfur in the melt at three temperatures: 1170°, 1250°, and 1300°C. The results show that a) the conductivity of copper-rich Cu,S is independent of the sulfur pressure in the furnace, and b) the conductivity of sulfur-rich copper sulfide increases rapidly with sulfur pressure. Assuming that the band theory is applicable to liquids leads to the conclusion that copper-rich copper sulfide is an intrinsic semiconductor, in which case electrons act as carriers. The activation energy for conduction in this case has been calculated to be 0.7 ev. On the other hand, sulfur-rich copper sulfide behaves as a p-type semiconductor, positive holes being responsible for conduction. IN order to elucidate the structure of Liquid copper (1) sulfide, Derge, Pound, and Osuchl have studied the electrical conductivity of this compound as a function of temperature. Their results showed that the conductivity is rather high, of the order of 100 ohm" cm", and that the temperature coefficient of conductivity is positive. This high conductivity seemed to indicate electronic rather than ionic conduction. This conclusion was checked further by Derge, Pound, and Yang,2 who measured the current efficiencies of copper sulfide melts at various temperatures. In all cases, the current efficiency was found to be nil, indicating the absence of appreciable ionic contribution to the conduction in

Jan 1, 1958

By R. C. Croft

Many chemical methods of upgrading ilmenite to enhance its titanium dioxide content involve reduction of the FeO in this mineral followed by solution of the metallic iron produced. While the use of most mineral acids for this purpose entails acid regeneration or salt disposal problems, these difficulties can be overcome with carbonic acid. Satisfactory rates of iron removal have been achieved at temperatures below 100° C and at CO, pressures up to 600 psi. Lowering of gas pressure over soluble bicarbonate solutions permits recovery of CO. and precipitation of iron oxide. The removal of the manganese, often present in ilmenites, is also feasible with these treatments.

Jan 1, 1972

By David A. Thomas, John F. Peck

Sam Leber (General Electric Refractory Metals Laboratory)—I think that the authors should differentiate between the curved grains obtained by swaging and the crumpled grains produced by drawing. This can be seen most easily in the transverse sections of Fig. 2d, and is also apparent in Fig. 2c. This difference in structure indicates that the mode of deformation shou1d affect the texture, since the cylindrical texture should be maintained or even increased by the curved grains developed by swaging. Drawing, on the other hand, crumples the grains. This should convert the cylindrical texture into a normal fiber texture. This has been substantiated by a comparison of tungsten wires fabricated by similar drawing and swaging schedules. Although cylindrical textures have been detected in drawn iron wires, they were weak in comparison to tungsten wires which included swaging as part of the fabrication process. It should also be noted that large curved surfaces developed by swaging are concentric with the surface. The postulated (100) surface of these crystals would be confirmed by a (100) cylindrical texture, as was observed in tungsten. The preservalion of the (100) cylindrical texture by swaging would maintain the <100> direction in the radial position required for easy flow. This might provide a partial explanation for the decreased rate of work hardening observed in the swaged wire. J. F. Peck and D. A. Thomas (authors&apos; reply) — The authors appreciate Dr. Leber&apos;s comments on the differences in textures, microstructures, and properties of swaged and drawn wires. The evidence of the prominence and persistence of the cylindrical texture in swaged bee wires seems quite consistent with our microstructural observations and interpretations. We are presently engaged in further work to correlate the development of texture and micro-structure in drawn bee metals.

Jan 1, 1962

By S. W. Parr

FROM a study of sulfur with reference to its specific combination in coal, published as University of Illinois Bulletin No. 111, 1919, it is now possible to determine the various forms of this constituent with a good degree of accuracy. This fact suggests two questions: (1) Are the same analytic methods applicable to coke? (2) Is there any correlation between the forms of sulfur as it occurs in coal and the residual sulfur found in the finished coke? The answer to the second question might be helpful in answering a still further question as to what chemical route the sulfur travels during the carbonization process. While the special studies along these several lines are by no means complete, a few preliminary statements are herewith presented. They may, at least, prove suggestive of further possibilities from a continuation of research along these lines. There is no reason, chemically, why the analytic methods devised for coal should not apply to coke and a fair amount of experience in connection with such use affords confirmation of this statement. The procedure in the case of coal may be briefly outlined as follows; Combinations of sulfur as sulfate, or sulfides other than FeS2, are readily dissolved without disturbing either the pyrite sulfur or the sulfur that is in organic combination by means of dilute hydrochloric, acid-1 part of concentrated HC1 to 10 parts of water or approximately 3 per cent. acid. Digestion at 60° C. for 24 hr. insures the complete removal of the sulfur thus combined. In freshly mined coal the amount of such sulfur is very small; weathering processes, however, may very materially increase the amount of sulfate present.

Jan 9, 1919

By A. U. Seybolt, C. H. Mathewson

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrence of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below.

Jan 1, 1935

By Hassell E. Hunter

The Wyoming Minerals - Conoco Crownpoint Joint Venture represents the first time that big hole drilling has been exclusively used to develop a privately financed mine. Three shafts, one ten feet in diameter and two six feet in diameter, have been successfully drilled to depths of 2243&apos;, 2188&apos; and 2188&apos; respectively and lined with hydrostatic designed steel casing. The largest shaft is to be used to as a development shaft to handle muck and water from enlargement and station excavation of the other two shafts. A reverse fluid air assist circulation system with potassium base mud was used during drilling. The mud was cleaned by settling in steel lined tanks with assistance from cyclone type sand separators. Deviation was monitored with wireline gyroscopic surveying instruments at 30 foot intervals. Horizontal departure did not exceed 16 inches off perpendicular. Casing was designed to withstand full hydrostatic pressures with a 1.5 safety factor for the large shaft and 1.25 safety factor for the two smaller shafts. All casing welds were x-rayed prior to lowering the casing into the hole. Cementing the annular space completed the operation. The total time to mobilize, drill and move off the three shafts was 363 days. The drilling operation was completed ahead of schedule and under budget.

Jan 1, 1982

By I. J. Corrans

Wet high-intensity magnetic separation (WHIMS) has been successfully applied to the recovery of gold and uranium from the residues of Witwatersrand ores. Good overall recoveries have been achieved for particles as small as 12µ, and finer particles of uranium minerals are recovered when present as inclusions. The best results were obtained with a matrix of soft-iron balls 6 mm in diameter. However, pilot-plant tests drew attention to a major defect of the machine: the matrix could be blocked by wood chips and ferromagnetic particles. This problem was overcome by the incorporation of a modification that allows the balls to be discharged from the rotating annulus. Two full-scale units that incorporate the modification have been installed.

Jan 1, 1980

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining reports, maps privately issued, and similar material, which will be classified, indexed, and, made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 6, 1914

By Carl Beal

IN February, 1918, the conclusion was published by Lewis and Beal1 "that wells of equal output on the average will produce equal amounts of oil in the future, regardless of the ages of the wells." This conclusion was based upon the study of data collected principally in Oklahoma and was not known at that time to be true for other oil fields. An abundance of statistical proof was later, collected by the senior author of the present paper, which showed that the conclusion was undoubtedly well founded and that it applied to other fields as well. Accordingly, it was later restated2 as the "law of equal expectations" as follows: "If two wells under similar conditions .produce equal amounts during any given year, the amounts they will produce thereafter, on the average, will be approximately equal, regardless of their relative ages." Although only scanty data from the California oil fields were available at the time this publication was prepared, sufficient information was analyzed upon which to base the insert on Fig. 80, which showed beyond a doubt that the law held at least for a part of the Midway oil field in California. Recently the authors have collected more complete data in California, and it is the purpose of this paper to explain the method used in demonstrating the truth of the law and, in addition, to give several methods by which curves constructed in accordance with this law can be used in a practical way with ease and accuracy.

Jan 8, 1919

By M. R. Louthan, C. L. Angerman

In polycrystalline Zircaloy-2 the orientation of zirconium hydride precipitates is influenced by an applied stress during hydride precipitation; hydride platelets are oriented nearly parallel to a compres-sive stress and perpendicular to a tensile tress. 1,2 A similar effect has been observed in the Ti-H system, where precipitation of the low-density hydride platelets occurred on habit planes made energetically favorable by the application of stress. 3 Recently, stress activation of hydride habit planes in zirconium and Zircaloy-4 was also demonstrated. The hydrides precipitated on {101l), {112l} and (2131) planes in both zirconium and Zircaloy-4; however, no platelets were found near the prism-plane positions in the Zircaloy-4 samples. Investigations at the Savannah River Laboratory, using polycrystalline Zirc_aloy-2 samples, have confirmed the (101l) and (1121) habit planes but also showed that the prism planes were active hydride habit planes. Using single-surface stereographic analysis and back-reflection Laue techniques, most of the previously reported habit planes for a zirconium were observed.4"1 and one additional plane, the (1013) plane, was noted, Table I. All the habit planes observed had the form (101l) or { 112l) indicating that these planes are the habit planes for hydride precipitation in poly-crystalline Zircaloy-2. The specimens used in these studies were cut from large-grained weld areas of seam-welded tubing and were hydrided in either a static steam autoclave at 400°C and 1500 psig or in a modified Sieverts apparatus at 400°C.

Jan 1, 1967