Search Documents

By James Gayley

The lining of the hearth and bosh of a blast-furnace has naturally come to be considered its weakest part, being subject not only to abrasion, but also to intense chemical action. In order to provide against rapidity of wear, it was formerly customary to build the lining from the mantle to the top first, and to put in afterwards the hearth and bosh, drawing the latter into a recess that had been reserved for it in the upper lining. At some works this practice still prevails ; but through the progressive development of cooling-devices, it has become possible to protect the bosh so well as to make it the most durable part of the furnace. The main question now is, by which one out of several methods the best economy results can be obtained. The plain bosh-jacket, made of wrought-iron or steel, and frequently called the air-cooled jacket, was a great improvement over the crinoline-construction formerly in vogue; but it was difficult in many cases to persuade furnace-managers, that in order to secure its best effects, they must discard the thick bosh-walls and put in comparatively thin ones. Mr John M. Hartman, who did more perhaps than any one to extend the use of these jackets, invariably contended for a 13-inch wall, the thin wall being an essential part of this construction. Later, a coil of pipe was placed just inside the jacket, through which water, circulating freely, contributed further to the proper maintenance of the walls. Undoubtedly much better results have been obtained in practice where the iron jacket has been supplemented by a coil in this way. It is safe to say that this combination of water-coil and jacket is much better than external sprays on the jacket; but it does not prevent the brick-work from cutting entirely away, which enlarges the bosh to that extent and interferes with the economy and output of the furnace. In case of leakage or stopping-up of the pipes, they cannot be replaced. A leading blast-furnace manager who is now using this construction

Jan 1, 1893

By Alexander Field

THE rate of elimination of carbon largely controls the time required to make a heat of steel by the basic open-hearth process and to an important degree determines the cost of refining. Practical experience has led to the generally accepted belief that the use of slags relatively high in iron oxide, such as are required to bring about rapid refining, leads to a certain sacrifice of quality in the product. As a consequence, a compromise must be made between the exceedingly slow rate of carbon drop which would correspond to the ideal case and the rapid rate which would best satisfy the condition of minimum cost. An increase in rate of refining necessarily implies an increase in the concentration of iron oxide dissolved in the metal. However, even for the infinitely slow rate that corresponds to slag-metal equilibrium, the metal would contain a certain definite concentration of dissolved iron oxide. It is a matter of great practical importance, therefore, to determine the quantitative relation between the minimum or equilibrium concentration of iron oxide in the metal and the higher concentrations which must actually obtain in practice. The present paper is devoted to the development of certain equations, derived from the established laws of physical chemistry, which will enable this relation between rate of refining and the degree of oxidation of the metal bath to be computed from operating data. No attempt is made to exhaust the possibilities of this general method of treatment. In considering rate of refining, attention is mainly confined to rate of carbon elimination. However, the equations are of a more general nature and their application may readily be extended. The results of the preliminary calculations given herein indicate that increased rate of refining may have a decided effect in increasing the concentration of iron oxide dissolved in the metal. The uncertainty. which attaches to the calculated value for this relationship arises in part from probable errors in experimental data on which the calculations are based, and in part from the lack of complete or favorably disposed information on basic open-hearth practice.

Jan 1, 1928

By William A. Edmiston, R. E. Grace

A simplified model for the theory of reaction rates near equilibrium has been applied to the reduction of wustite. A linear relationship between the net rate of reaction and the Gibbs free-energy change, ?F, is predicted. The reduction of wustite in H2 -H2O gas mixtures was studied with a microbalance technique at temperatures from 850° to 950 °C. The predicted model was found to be valid to -?F/RT = 0.1 or approximately -200 cal per mole away from equilibrium. ThE theory of reaction rates near equilibrium has been developed by a number of authors. Prigogine, Outer, and Herbo1 have studied the catalytic hydrogena tion of benzene in an attempt to deduce some intrinsic connection between reaction rates near equilibrium and thermodynamics. Manes, Hofer, and weller2 have derived more general expressions for reaction rates near equilibrium from classical thermodynamics. Hollingsworth3,4 has commented briefly on the work of Manes et al. Benson5 has summarized in a general way the results of the earlier contributions. It is the purpose of this paper to apply the theory of reaction rates near equilibrium specifically to the reduction of wustite in H2-H2O gas mixtures. The basic premise is that the reduction of wustite proceeds by a surface reaction, rather than by solid-state diffusion ,or gaseous diffusion. Richardson and Dancy6 and Gellner and Richardson7 have suggested that the reduction of wustite may be governed by iron diffusion in wustite. Mckewan8-11 has proposed that reduced iron layers on various oxides are sufficiently porous to offer a negligible impedance to the reducing gas. The linear motion of interfaces reported by McKewan and discussed by Themelis and Gauvin12 indicates the lack of diffusive control during reduction. The reduction studies of magnetite reported by Quets, Wadsworth, and Lewis13 give additional evidence that reduction rates are linear when the reaction products are porous and nonprotective. The interpretation of measurements reported in this paper is predicated upon a surface-controlled reduction reaction, at least in the earliest stages of reduction when the reduced iron layer is thin.

Jan 1, 1967

By J. A. Herbst, G. E. Agar

The effect of fluid viscosity on the classification of solids in a liquid-solid cyclone was investigated. The separation size was found to be proportional to Additionally, it was found that the prediction of flow rate through a cyclone is dependent on a Reynolds criterion. Above a critical value, the flow can be predicted by a simple equation, whereas, below this value a variable orifice coefficient must be introduced. INTRODUCTION The solid-liquid cyclone is widely used as a device for classification, thickening, and heavy media separations. The more important variables and how they affect the performance of a cyclone are known and have been the subject of several investigations.' In general, these studies have paid little attention to the viscosity and those which have, introduced it through Stokes settling considerations. Systems which contain appreciable amounts of swelling clays exhibit viscosities much greater than water, and in these systems the viscosity term becomes important in determining the separation size. The work described here was done to determine in a Newtonian system the dependence of separation size on viscosity. BACKGROUND The separation size for a cyclone classifier has been related to the parameters of the cyclone by an equation of the form: where a is probably between 1.3 and 1.5, ß is between 0.50 and 0.57, and 6 has a theoretical value of 0.5. where y has a value between 1.8 and 2.0. Although these relationships are empirical, equations that differ only in the exponents have been derived from theoretical considerations. Those interested in the origin of these equations are referred to some of the original work.6,7 MATERIALS AND PROCEDURE The laboratory apparatus used in this study is pictured diagramatically in Fig. 1. Feed slurry was pumped from an agitated 15-gallon plastic tank by a centrifugal pump driven by 3/4 hp motor. The static pressure of the feedstream and thus the pressure drop through the cyclone was measured on a gage located as close to inlet of the cyclone as possible. When samples were not being taken, overflow and

Jan 1, 1967

By Eugene H. Dawson

MICA is a mineral that once was a familiar sight as fireproof windows in stove and furnace doors and as lamp chimneys and shades. Since 1878, the beginning of the electrical age, the use of mica for such purposes has gradually declined and its use in electrical equipment and appliances has developed to such an extent that the known sources of supply are scarcely equal to the demand. With the increasing capacity of electric generating units, the size of mica sheets found in nature was inadequate. However, in 1894, a process was developed whereby thin films or splittings cemented with shellac or other binders could be pressed into large sheets. 18 The introduction of radio in the early 1920s created such a heavy demand for the smaller sizes of mica that on March 22, 1938, mica was included among 23 commodities on the list of strategic materials approved by the United States Army and Navy Munitions Board. To be included in this list, the material must be one whereof the domestic supply is not sufficient to meet the demand. COMPOSITION Mica is a complex mineral composed principally of the silicates of potassium, aluminum, and magnesium. Less prevalent species contain, as essential components, lithium, vanadium, and chromium. Iron usually is present either as an essential component or as an impurity. The mica group comprises some nine different species, five of which, muscovite, phlogopite, vermiculite, lepidolite, and biotite, are widely used in industry. Lepidolite and zinnwaldite (lithium micas) and roscoelite (vanadium mica) are sources of lithium and vanadium. Muscovite, "white mica," is potassium mica. Theoretical formulas H2KAl3(SiO4)3. There are two varieties, distinguished as to color, known in industry as ruby and green. In crystals or "books," the colors each range through varying shades of red and green. However, when split into thin films, all micas, except biotite and phlogopite, are colorless and transparent. Muscovite frequently is stained red or black by thin films of iron oxide between the laminae. The staining usually is derived from magnetite, which sometimes is found as unaltered crystals.

Jan 1, 1949

By Henry F. Heblby

HOW often has the thoughtful observer pondered the apparent contradictions experienced in the weather? One can take records of two days, one in the winter and one in the summer. The "degree days1' indicate that space heating and domestic load were present in one case and not in the other. The Business Index may be about the same, indicating that the industrial activity of the area and its concomitant use of fuel were about the same. Thus the volume of the products of combustion released to the atmosphere varied only as related to the space heating demand. Yet on one day in winter the atmosphere may be clear and bracing, while on a summer's day the air is thick and murky and the visibility sharply reduced. The situation may be reversed. What are some of the factors that contribute to the creation of these conditions? These few notes have been prepared to indicate some of the influences that are exerted on the problem. The Sources of Atmospheric PolLution The industrial area of Pittsburgh, Pa., has been a dominant center for the production of iron and steel for over one hundred years. In fact, with the growth of the numerous auxiliary processes Allegheny County which contains Pittsburgh is prob- ably the most industrialized county in the world. In addition, the type of manufacture carried out in this area is predominantly dependent on thermal energy (heat). That energy is supplied from coke and coal produced in the vicinity of Pittsburgh Indicative of the stupendous quantities of fuel that are employed in this industrial area's economy, the following (Table I) taken from the U. S. Census (1940) may be of interest. In tonnage consumed in the area, the figures are equally impressive: Annual Tons oF Coal Metallurgical Industries.... 35,000,000 to 40,000,000 Commercial Installations (Pgh.)................. 1,500,000 Domestic hand-fired) (Pgh.)................. 750,000 An influence that has never been fully appreciated by many individuals is the fact that no matter what adventures the gases of combustion experience as they pass through the various processes, uti-mately the spent gases are discharged through chimneys to the atmosphere.

Jan 1, 1949

By E. T. Wessel

UNEXPECTED brittle failures of metals in practical applications are a serious problem to many industries and to the nation as a whole. Considerable effort has been devoted to studies of the brittle behavior in metals. However, the major portion of this effort has been directed at developing techniques and apparatus for the purposes of determining the susceptibility of metals to brittle failure and of making various types of observations of the phenomena. Relatively minor effort has been made to understand the basic mechanisms involved in initiating brittle failures. A more complete understanding of the nature and mechanism of the brittle failure problem would be very helpful in efforts directed toward predicting and avoiding brittle failure and toward the development of suitable materials and designs that are not susceptible to a brittle behavior. The intent of the present investigation is to acquire this basic understanding. The pronounced transition from a ductile-to-brittle behavior is most prevalent in metals having the body-centered-cubic lattice structure, primarily be- cause metals of this structure exhibit a strong dependence of yield strength upon temperature and the rate of straining. The generally recognized qualitative concept of the ductile-to-brittle transition is that brittle (cleavage) failure occurs when the yield strength exceeds the cleavage fracture strength. This condition can apparently be achieved by decreasing temperature or increasing strain rate. Likewise, a normally ductile metal can be made to fracture in an apparently brittle manner by the introduction of triaxial stresses (notches) where the ratio of normal to shear stresses can be increased to such an extent that the normal stress exceeds the fracture strength before the critical shear stress for plastic flow is achieved. Neither of these concepts require any prior plastic deformation or explain why the observed fracture strengths are so much less than the theoretical cohesive strength. The results of several investigations of the ductile-to-brittle transition in body-centered-cubic metals illustrate rather conclusively that measurable amounts of nonelastic deformation do precede cleavage fracture, even at extremely low temperatures. These studies suggested that the early stages of plastic flow, particularly abrupt yielding, and their relationship to brittle fracture should be examined

Jan 1, 1958

By C. A. Fisher

THE advent of the Rocky Mountain States into prominence as an oil-producing region is comparatively recent. Scarcely more than a decade has passed since the number of producing oilfields in this part of the country were few and their combined yield small and relatively unimportant. However, oil was discovered and recorded near the present site of Lander, Wyo., as early as 1833 and in 1867, on the comple-tion of the Union Pacific R. R., the site of this oil discovery was located, among other things, as a natural resource of economic importance. In that year a well was drilled for oil, to a depth of 480 ft., near Evanston, Wyo., but later was abandoned. In 1883, the Lander district witnessed the successful completion of the first oil well in the state. In Colorado, oil was first produced from shallow open wells near Canon City and sold to prospectors in 1864; in 1887, the Florence oilfield was discovered and a commercial production developed. While the Rocky Mountain States have never gained the prominence as an oil-producing region attained by the Pacific Coast, Mid-Continent, or Gulf fields, a substantial and increasing production is being taken from the Rocky Mountain province. At the close of 1923, the oil industry in this region has 38 oil and 21 gas fields producing, or capable of producing, oil or gas in a commercial way with a combined annual yield of nearly 47,000,000 bbl. of oil, a daily refining capacity aggregating about 90,000 bbl., upwards of 17,000,000 bbl. of crude in storage, and an 8-in. pipeline, nearing completion, 600 miles long which will connect the most prolific oilfield of the Rocky Mountain States with a trunk pipeline between Mid-Continent and the east at Carrollton, Mo. Several of the larger standard and independent operating companies are now represented in this region and, in the last ten years, there has been developed at Casper one of the large refining centers of the west. Fig. 1 illustrates the rise in production of four of the larger fields, also in the total production of the state; in addition there is given the yield of the larger fields of Wyoming and Montana for 1923.

Jan 3, 1924

By E. H. Crabtree, J. D. Vincent

Probably no metallurgical process in the history of the mining industry has been responsible for such increased mineral production as has flotation. It has made possible the economic treatment of low grade and complex ores which, with the old methods of gravity concentration, would have been classed as worthless. Starting with the sulfide ores of copper, lead, and zinc, the process has been applied to almost all metallic and nonmetallic minerals. Today, the sulfides of the common metals not only can be readily recovered, but can be separated from each other. Thus, three or four mineral recoveries from the same ore, such as galena, chalcopyrite, sphalerite, and pyrite, are possible. Molybdenite is recovered initially with copper sulfides and the two are subsequently separated. Flotation of metallic gold and of native copper and graphite is being commercially practiced. The carbonates of some of the base metals, principally those of lead, can also be concentrated. Flotation of the oxides, silicates, phosphates, and other so-called non- metallic minerals represents the greatest advance in the art in the last few years. Today, commercial plants are successfully treating such minerals as feldspar, garnet, ilmenite, muscovite, cassiterite, cement rock, fluorspar, phosphate rock, sylvite, and a host of others. Flotation of the various types of iron ores along with other concentration methods is today the subject of a tremendous amount of investigation on the iron ranges. EARLY PATENT HISTORY OF FROTH FLOTATION Although what we call the froth flotation process as distinguished from bulk oil processes was not used commercially until 1905, many investigators had recognized its possibilities long before the twentieth century. The principal patents issued throughout the years give us a method of recording early flotation history. BULK OIL PROCESSES: In 1860, William Haynes patented (British Patent 488) a process for separating oil-wetted sulfide minerals from water-wetted gangue minerals by agitating the dry ground ore with oil and then the mixture with water. In 1877, the Bessel brothers patented (German Patent 42, Class 22) a process where a mixture of graphite ore was mixed with 1 to 10% oil; after adding water, the

Jan 1, 1962

By M. R. Geer, Franklin T. Davis, H. F. Yancey

COKE with low phosphorus content is required by some of the electrometallurgical and chemical plants recently attracted to the Pacific Northwest by the hydroelectric power available from Bonneville and Grand Coulee dams. Shipping such coke into the area from eastern points involves a high freight charge, and during wartime consumes precious rail and ship-bottom space, so it is highly desirable to produce coke from the coking coals of Washington to meet the requirements of these industries. Although coke has been made from Washington coals since 1884, little has been known about their phosphorus contents or about the extent to which phosphorus could be reduced by cleaning. An investigation was undertaken, therefore, to determine the manner in which phosphorus occurs in the coking coals of Washington and its amenability to removal by ordinary coal-washing methods. PREVIOUS WORK Phosphorus is a deleterious element in coke used for numerous metallurgical processes, including the production of pig iron, yet comparatively little published information is available on the occurrence and elimination of phosphorus in any of the coals of this country. A variation from 0.009 to 0.062 per cent phosphorus in various horizons of the Pittsburgh bed in the Connellsville region of Pennsylania has been reported,1 and a reduction in phosphorus content from 0.020 per cent in the raw coal to 0.018 per cent in the washed coal was obtained in washing coal from the same bed in the Pittsburgh area;2 the latter figures represent average analyses for a year's operation of the washery on about 800,000 tons of coal. A reduction in phosphorus content from 0.018 to 0.011 per cent in washing coal from the Pittsburgh bed at another washery was observed, and the same report provides data on the phosphorus reduction obtained by separating 10 other coals on a bath of 1.35 specific gravity.3 European investigators have been especially active in correlating phosphorus content with petrographic analysis; fusain and durain generally contain the highest percentage of phosphorus, but this relationship is not universal.4 Some of these investigators have found that phosphorus is removed in the coal-washing process,5 but others have observed that the clean coal contained as much or even more phosphorus than the raw coal.6

Jan 1, 1944

By M. C. Fuerstenau, A. M. Gaudin

Understanding the sedimentation of relatively thick suspensions depends on a knowledge of the concentration of the solids at various positions in the pulp and the times required for thickening. Flocculated kaolin slurries were studied with the transviewer, a device utilizing X-ray absorption in conjunction with a scanning mechanism. A mathematical model based on the Schuhmann size distribution in conjunction with Poiseuille's law yields experimental filtration rates as a hction of pulp density. These calculations show accord with the experimental results. Accurate predictions of sedimentation results depend upon determining the number and size of pores for given conditions, since the voidage of the suspension controls the volume of liquor that can pass through an element of suspension per unit time. A study on the sedimentation of flocculated kaolin slurries has indicated that their sedimentation takes place by two different processes, dependent on the initial concentration of solids in suspension. One process occurs in dilute suspensions (less than about 2 pct solids by volume) in which a multitude of relatively small flocs settle by hindered settling. In this case, maximal settling velocity is independent of container geometry.1 r2 The other process occurs in relatively concentrated suspensions (greater than about 2 pct solids by volume) in which the mass is considered to be settling as an aggregate network or as one large floc, defined as to size by the dimensions of the container. In this case, container geometry affects sedimentation results significantly. Furthermore, it seems that this single floc is in a state of compression from the beginning of settling, and that two phases of compression settling exist during sedimentation. The first occurs during the early stage of settling where liquid exudes easily and rapidly from the floc, while the second occurs in the compacting portion of the floc where water escapes more slowly and with much more difficulty. Sedimentation of relatively thick suspensions may then be thought to be a filtration phenomenon in which a pulp thickens by the filtration of its contained liquor through the aggregate network of pulp above it. This postulate has also been advanced by others.,4 To understand the sedimentation of relatively thick suspensions more fully, it was felt that knowledge of the concentration of solids at all positions in the

Jan 1, 1962

By Robert V. Whitman

INTRODUCTION Ideally, this paper should start by citing examples of slope failures in open pit mines during earthquakes. I do not know of any such examples, although - since my search of the literature has not been exhaustive - such examples may well exist. However, there certainly are many examples of devastating earthquake-induced landslides, and there is no reason why such landslides cannot occur at large open pits. Moreover, many of the actual earthquake-induced landslides have seriously affected mining operations in one way or another. Hence, this paper will treat earthquake-induced landslide phenomena in general, in the hope and expectation that the reader can apply this general knowledge to the specific problems associated with open pit mining. Ultimately, of course, the aim is to predict the likelihood of the occurrence of earthquake-induced landslides, and to delineate steps which can be taken to minimize the possibility of their occurrence. These aims can be achieved only imperfectly at the present time, for our knowledge concerning earthquake-induced landslides is still in an embryonic stage. Nonetheless, much useful knowledge does exist. In order to understand and apply this knowledge, it is necessary to: 1. Review the nature and extent of actual earthquake-induced landslides; 2. Have a grasp of the basic terminology and concepts of seismology; 3. Study the fundamentals of probability-based seismic risk analysis; 4. Appreciate the way in which earth materials behave during earthquake loadings; and 5. Have a general knowledge of the methods currently available for analyzing the dynamic response of slopes. Much of this paper is devoted to this necessary background. Information of practical use in connection with various classes of slope stability problems is assembled in the final sections. LANDSLIDES DURING PAST EARTHQUAKES Almost every earthquake in mountainous country, strong enough to be reported in the literature, has caused at least some landslides and rockfalls. Unless these slides or falls damage

Jan 1, 1971

By H. R. Aldrich

This paper is not a treatise on the theory and practice of magnetic surveying. It presents a diagram upon which have been plotted observations taken with the simplest form of magnetic instrument, the lowly dip needle, over a large area astride the Lake Superior syncline of northern wisconsin. The exposures of the underlying formations are not sufficiently great in number nor fortunate in distribution to have provided the fuller understanding of the geology which has been secured by the use of the magnetic observations as an auxiliary tool or accessory in the hands of the geologist. The diagram (Fig. 2) in large part speaks for itself if studied in connection with the geological map (Fig. 1) for which it is the main control. It is presented to demonstrate the extent to which the use of such methods may aid in the solution of geological problems in a covered country. The diagram is probably unique in assembling the expression of such a wide range of formations, affected by so wide a range of secondary processes, and deformed by so many different structures in terms of magnetic variation. Few geologists outside of the Lake Superior country have had any first-hand experience in the taking of magnetic observations and the interpretation of the results in terms of geological conditions; nor have the Lake Superior men gone with the methods far afield from the mere tracing of iron formations. In more recent years the oil companies have gone heavily into investments in magnetometers, balances, and dip needles in the quest of concealed structural anomalies which are the favorable loci of petroleum accumulation. But these geophysicists come back from the fields with their collections of observations facing the question of interpreting the geological meaning of their magnetic anomalies. It is considered probable therefore, and certainly it is the hope of the writer, that the appended charts, or magnographs, which show how character of the country rock and its changes, structural strike and dip and their changes, depth of burial and its variation, contact metamorphic

Jan 1, 1929

CHARGING of an open-hearth heat is begun as soon as possible after the previous heat has been tapped. Ordinarily, about 40 min is required to drain and dress the furnace hearth, make up the taphole, and perform routine repairs of the banks. Repairs to the upper back wall and to the front wall and jambs can ordinarily be done while the first scrap charge is being heated and are therefore allowed to wait in order to save furnace time. Any major repairs required on the hearth or other parts of the furnace necessitate longer delays because such repairs must be made while the furnace is empty. Although charging practice varies considerably in detail with the type and proportions of scrap and iron used, many factors are common to all varieties of charge. Such general considerations are dealt with first. CHARGING EQUIPMENT AND STOCK HANDLING The physical equipment available for loading and weighing the stock, transporting it to the furnace, and charging it, may have a major effect on charging practice. Limestone, scrap, and all other solid melting stock are charged mechanically by means of equipment illustrated in Fig 2-1. The charging of hot metal is shown in the background of this figure. Mechanical equipment and plant layout for stock handling are described in Chapter 1. It is generally desirable to charge the scrap about as fast as the physical volume can be put into the furnace. Charging scrap that is too heavy or adding the charge too rapidly (less than 45 min) may be detrimental to melting rate because of excessive chilling of the entire furnace system and also because of poor conduction of heat to the lower layers in the furnace; but the more common problem is the reverse one of charging light 'scrap fast enough to maintain a normal heat time. A limiting factor may be the height to which the scrap may he piled in the fur-

Jan 1, 1951

By Ralph J. Schilthuis, William Hurst

The nature of the forces that are important in producing the oil in the East Texas field and the manner in which these forces are affected by the rate of production have always been problems of outstanding interest. These questions are of great interest to the industry as a whole on account of the economic importance of the East Texas field and to the engineers in particular on account of the unique character and behavior of the field. Subsurface pressure data throughout the field have been collected systematically, so that a quite complete history of the reservoir pressures has been kept as the field has been developed and produced. Subsurface samples of the oil and gas have been taken and these have been examined to obtain data on the physical properties of the reservoir fluids under the actual conditions of temperature and pressure. All of these data have been valuable because they have afforded the basis for a careful study of the means by which the oil is produced. It is the purpose of this discussion first to point out several of the important facts revealed by the data mentioned and then to describe studies that have been made concerning the interpretation of these facts. Reservoir Pressure Data and Properties of Oil The reservoir pressure data on the East Texas field have shown conclusively that the pressures are readily affected by changes in the rate at which the field is produced. This can well be seen in Fig. 1, where the average reservoir pressures obtained from time to time are plotted with the daily production rates and the cumulative production of the field. It is noted that the average reservoir pressure has declined irregularly, depending upon the rate of production, from the estimated original value of 1625 Ib. per sq. in. to the value of 1228 lb. per sq. in. observed for Aug. 11,1934. The decline in pressure has been more rapid at the higher rates of production than at the lower rates. In contrast, the average reservoir pressure has increased, on several occasions, upon reduction of the withdrawal rate from a high value to a lower value. The reservoir pressure data have also shown that a definite gradient in pressure has existed across the field from west to east since the begin-

Jan 1, 1935

By P. B. Liebermann

The resistance to motion offered by mine cars is caused principally by: Rolling friction, flange friction, bending rails, bearing friction and wind resistance. With proper construction and with a fair amount of attention and care, that is, under favorable conditions, the first three items cannot be greatly improved. The wind resistance ordinarily is negligible on account of the slow speeds commonly used. The bearing friction, however, is a variable item, depending upon the design, the bearing material, the lubrication, the location (whether in wheel-hub or on car-body) and the alignment. Under the most favorable conditions the bearing friction will reach a lowest possible value. By the development of a successful anti-friction mine-car bearing this lowest value has been improved to such an extent as to affect the whole system of mine haulage. After being satisfied of their durability and certainty of operation, any investigation into the advantages of anti-friction bearings for mine cars will have to be based upon reliable information as to the saving in power of such bearings. While numerous tests have been made in this direction, the results have not always been convincing, principally because of the rather crude methods that were employed. These crude methods are the main cause of the wide variations existing in regard to the exact amount of the frictional resistance. Frequently an ordinary spring balance is used and the pull necessary to move a certain car or train of cars is obtained by a number of readings. Such spring balances necessarily have a coarse graduation and the continuous vibration and fluctuations to which they are subjected make them highly dependent upon the individual observer. Further, they must be frequently calibrated. Sometimes these tests were made without regard to acceleration, speed or even grade. The method of using an electric locomotive as a testing device is perhaps more open to criticism than the spring-balance method, because it introduces additional sources of error: The varying electrical and mechanical losses in the locomotive. Also, such a measurement always includes the power necessary to move the locomotive itself. This means a considerable amount of figuring, and the results due to the various multiplications and corrections may be of little value, for obvious reasons. When figuring the drawbar pull from the electrical

Jan 1, 1917

By Cecil H. Desch

The progress of metallurgical practice and the demands made by the engineering industry on our foundries and mills have made the crystalline structure of metals a subject of far more than academic interest. Metals and alloys are made up of crystals. Even if we accept the view, so ably maintained by some metallurgists, that the crystals are separated from one another by an amorphous layer, it remains true that all but a very minute fraction of any metallic mass is crystalline. The conditions which affect the growth of crystals are therefore of importance in metallurgy. It is not only castings whose properties depend on the arrangement of their crystals, for the more we learn of the behavior of forged, rolled and drawn metals, the more certain it becomes that it is profoundly influenced by the size and arrangement of the crystals in the original ingot, determining a structure which may persist in a modified form through a long series of mechanical operations and annealings. This is mainly due to the concentration of much of the impurities in the last portions of the liquid to freeze, so that the boundaries between single crystals or groups of crystals are marked out by a zone of segregated material, differing in properties from the mass, and offering a barrier to diffusion and equalization of composition throughout the whole. The importance of this fact has been fully recognized by steel manufacturers, who have to deal with ingots which are sometimes very large, and are cast at a high temperature, containing impurities which have a marked effect on the properties even when present in very small quantity. For this reason the Iron and Steel Institute has set up a committee to examine the whole question of the heterogeneity of steel ingots,(1)† and a report has been issued, containing an account of the structure of 16 ingots, ranging in weight from 15 cwt. to 172 tons, each of which was sectioned and examined by chemical analysis and by etching. A valuable body of data concerning segregation has thus been collected. The work of the committee is being prosecuted with great activity, and at the same time researches are in progress to determine the physical

Jan 1, 1927

By J. C. Febles

The use of iron for the precipitation of copper was known at least as early as the fifteenth century. Both Paracelsus and Basil Valentine refer to it in their writings, as early as 1500 A. D. It was used in Peru for this purpose prior to 1637, and at Rio Tinto, Spain, as early as the sixteenth century. The statement has been made repeatedly that in the early history of the mining industry at Butte, the practicability of this method of recovering copper from solution was overlooked, and that enormous quantities of copper-bearing water were allowed to go to waste, the copper in which might easily have been recovered at small cost; and that this oversight on the part of the mine operators was due to ignorance of this method of recovering copper. As a matter of fact, very little copper-bearing mineral was encountered in the mines of Butte until a depth of 400 or 500 ft. had been reached, and in many cases much greater depths were necessary to reach the copper-bearing zone. The water encountered in the upper levels (although in most cases quite highly mineralized) contained little or no copper, and it was only after considerable areas of copper-bearing ore had been uncovered and developed that copper sulphate began to appear in the mine water in any considerable quantity. In fact, the first water that was observed to contain copper carried it in such small amounts as to be of little or no importance. It was only after years of underground work had opened extensive areas of stopes, drifts, and other underground workings, these being subsequently filled with waste, nearly all of which contained small copper values, which became oxidized by exposure to the air and were acted upon by the slowly percolating mineral water, that the recovery of copper from mine water became commercially important.

Jan 1, 1914

By H. L. Hopkins, L. W. Kempf

Aluminum alloys, in common with most other metallic alloys exhibit slight density changes with variations in temper achieved by heat-treatment, which usually are the result of the variation with temperature of the solid solubility of the various alloy constituents in the solvent metal. Changes in density are, of course, most marked in conditions that exhibit the maximum variation in solid solubility of the constituents. In aluminum alloys these conditions usually prevail when alloys are quenched from just below the melting point and are subsequently reheated to some lower temperature. Since commercial heat-treatments may be of this type, the density changes, although small (of the order of 0.3 per cent which may be compared with the density change of about 1.5 per cent involved in the transformation, at ordinary temperatures, of gamma to alpha iron during the hardening of steel), may in some specific applications necessitate quantitative consideration. This phenomenon has been investigated extensively in the laboratories of the Aluminum Company of America over a period of years. A number of investigators '-5t have observed and measured the density changes accompanying the heat-treatment of aluminum alloys. In general, these changes have not been directly translated to dimensional changes and their significance has been overlooked to some extent by the practical user of aluminum alloys. It is the purpose of this paper to consider some practical aspects of these density and dimensional changes. These density changes were given some consideration in 1917 in connection with the use of aluminum-alloy pistons for aircraft engines. Investigations by Lea and Shakespear were reported in some confidential reports of the British Advisory Committee for Aeronautics, Light Alloys Subcommittee, during 1917 and 1918, which are not generally available in published form. In these reports the term "permanent growth" was applied to the dimensional changes occurring in the pistons at the tem-

Jan 1, 1936

By Paul B. Crawford, Bobby L. Landrum

Electrical model studies have been made of the effect of unsymmetrical vertical fractures on production cnpacity. The study war restricted to the case of two vertical fractures originating at the well and extending out into the reservoir for various distances and orientations. The ratio of the short fracture length to the long fracture length was varied from 0.1 to 1.0 in successive studies. The angle separating the two fractures was varied from 0 to 180 degrees. The most effective fractured patterns were obtained when the fractures were oriented 180 degrees. It was found that when the total fracture length was equal to 0.2 of the drainage radius, the increase in production capacity may vary from approximately 1.55 to 1.95. depending upon the ratio of the short fracture length to the long fracture length and the angle separating the two fractures. If the total fracture length were 0.5 of the drainape- radius. poroduction cavacitv., increases varving 1.95 to 2.65 were observed, depending on the angle between the fractures and the ratio of the .short fracture length to the long fracture length. The fractured well production capacity decreased aPproxin?ately I to 10 per cent as the angle separating the fractures was varied from 180 to 90 degrees. It was dependent on the particular fracture. The commercial application of reservoir fracturing techniques has caused an interest to be expressed in the effect of vertical and horizontal fractures on production capacities. Some data have indicated that substantially vertical fractures may be created in some reservoirs. It is believed that the fractures are possibly unsymmetrical, that is, one fracture may extend due north 100 ft and a second fracture on the opposite side of the well may extend south or southeast only 50 ft. The total fracture length, ratios of the lengths and angles of separation may vary considerably. For this reason variations in these factors were considered. The study was restricted to the case of two vertical fractures originating at the well and extending out into the reservoir. It is not known that such will occur in a reservoir, but the results may be of value in interpreting or studying fracturing applications. PROCEDURE An electrical model was used in this study of the effect of unsymmetrical vertical fractures on production capacity, A wooden tank 30 in. in diameter and approximately 2 in deep was coated with paraffin wax. A copper band was situated at the periphery and a single wire electrode was positioned at the center of the tank. The ratio of the reservoir radius divided by the

Jan 1, 1956