Search Documents

By Morris Muskat

The detailed analogy between flow systems in porous media and the corresponding poten-tiometric model systems is developed under conditions where it may be desirable to take into account variable pay thickness, variable porosity, and permeability, and also the dependence of the fluid density on pressure. It is shown that in such models it is only necessary that the electrolyte thickness be made everywhere proportional to the millidarcy-feet of the formation. In contrast to the iso-vol type model, previously suggested as a basis for the analogy, the porosity does not enter directly in the construction of the model. It is introduced only in translating the electrical voltage gradient measurements into the equivalent fluid travel times. A discussion of this procedure is given. I NTRODUCTION It is now some 50 years since it was pointed out' that on the basis of Darcy's law Laplace's equation must govern the steady state flow of homogeneous fluids through porous media. It is 16 years since the obvious implication of this fact, namely, that such steady state homogeneous flow systems in porous media could be simulated by electrical analogies, was first applied2 to problems of practical interest with respect to oil production. In these initial studies major emphasis was placed on the use of electrolytic models, made of blotting paper, to give a direct and graphic history of the fluid particle motion in regular and infinite well networks. However, it was also noted there that the basic requirement of the model was that it give a potential distribution similar to the pressure distribution in the flow system, and that from the electrical measurement of the potential distribution the fluid particle motion could be graphically or numerically determined. This was demonstrated by application to the five-spot infinite network, for which a conducting metallic sheet was used to establish the equipotential contours. As anticipated, the fluid particle motion computed from these contours agreed well with that given directly by the blotting paper model. For irregular well distributions it was found more convenient to use electrolytic bath analogs rather than metallic sheets. Several investigations,3'4 as applied specifically to cycling well patterns, have been reported with these models, which have become known as "potentiometric models." However, the extremely laborious nature of both the electrical measurements by direct probing and the associated interprctive computations retarded the widespread use of these procedures. The electrical measurements can be accelerated by using a four-probe electrodc,5,6 which provides a means for simultaneously determining the streamline paths along which the fluid particles must move and the voltage gradients along these paths which are proportional to the fluid velocitics. With the increasing frequency of discovery of condensate pools, as drilling depths are becoming greater, the applicability of the potentiometric model to production problems, and especially to the study of well patterns for cycling, has been given a fresh impetus. Although the formal theory for determining the motion of fluid particles in porous

Jan 1, 1949

By W. I. Duvall, D. E. Stephenson

A theoretical solution is given for the energy that is radiated outward when either a cylindrical or spherical cavity located underground in a uniform stress field is suddenly created or enlarged. The method of derivation shows that the stress field in the solid rock surrounding the opening does work on the rock because of elastic displacements that result when the size of the cavity is increased. The amount of this work is sufficient to account for both the increase in the strain energy in the rock surrounding the opening and the seismic energy that radiates outward. Thus, the source of the radiant seismic energy is mainly the gravitational potential energy and not the strain energy stored in the rock. The amount of the radiant seismic energy is directly proportional to the volume of the rock removed from the opening or relieved of stress. Seismic energies from rockbursts are compared with earthquake energies. Also, the amount of gravitational potential energy released by underground explosions is calculated and found to be small compared to the seismic energy generated by the detonation of the explosive. A review of the early literature on rockbursts shows that a number of investigators calculated the amount of energy released by rockbursts. 1-5 However, none of these papers give the formula used to make these calculations or a reference to the derivation of any formulas. The general impression that one obtains from these early papers is that the main source of the seismic energy released by rock-burst is the strain energy stored in the rock before it is fractured. However, a few of the early papers appear to have considered the solid rock at a distance from the mine opening as a possible source of the seismic energy. Recently Black and starfield7 gave a theoretical solution for the strain energy in a stressed plate with and without a circular hole. Also, Press and Archambeau8 gave the theoretical solution for the seismic energy released when a spherical cavity is created in rock subjected to a three-dimensional stress field. Both of the above theoretical papers start with the condition of no opening and calculate the strain energy before and after the opening is suddenly formed. Neither of these papers appear to have calculated the work done by the applied stress field as the cavity is enlarged. The rockburst problem associated with deep mining is concerned with the failure of the solid rock surrounding an underground opening. Therefore, it seems appropriate to consider theoretically the problem of suddenly enlarging the size of an existing opening. The purpose of this paper is to present the theoretical solution for the energy that is available for release as seismic energy when an underground circular tunnel or spherical cavity is suddenly enlarged in diameter. To keep the mathematics as simple as possible, a uniform radial applied stress field is assumed and the rock is assumed to be isotropic, homogeneous and perfectly elastic.

Jan 1, 1965

By M. E. Volin, F. H. Erbisch, G. M. Wenberg

Bacterial leaching of copper and uranium is practiced under acidic conditions in environments furnishing sulfur and iron. However, many mineral deposits do not have these conditions; the chalcocite and native copper deposits in Michigan's Upper Peninsula are examples. Species of bacteria and fungi isolated previously from samples taken at the White Pine Copper Co. tailings pond and mine, were screened for solubilization of copper from chalcocite ore and flotation concentrate and from native copper jig concentrate. Certain Penicillium species solubilized significant amounts of copper under neutral to slightly acidic conditions in a carbon and nitrogen-enriched medium. Leaching apparently was accomplished by release of metabolites which chelated with the copper. The copper yield was highly dependent upon the medium composition and the concentration of copper in the source material. The standardized procedures which were developed in an attempt to maximize copper yield in leaching times of three to five days are described. This preliminary research indicates a biological leaching process for copper which is different from those in use, but whether it can be applied economically remains to be determined.

Jan 1, 1972

By Vincent Carlsson

A comprehensive investigation has been undertaken to clarify how pellets are affected by alkali circulating in the blast furnace. The investigation has been performed with acid and basic pellets in a special furnace. Experiments were carried out to ascertain the influence of potassium on swelling and reducibility when added at different stages of reduction. After that, the significance of the quantity of potassium added in the hematite stage was studied. A parallel experiment with sodium as the alkali component was also con- ducted. Besides these vaporization experiments the effect of alkali on softening and reduction characteristics at high temperatures was investigated. The results showed that alkali always increases swelling, especially when added in the hematite stage. The addition of alkali increases reducibility of acid pellets during reduction from wustite to 70 % reduction. The softening temperature is significantly lowered by the addition of alkali and is, in any case, lower for acid pellets than for basic pellets. The microscopic studies showed that alkali ferrites can be formed irrespective of the influence of alkali on the slag phase.

Jan 1, 1977

By William G. [Peryam], Bishop Ottey M., Fred E. Johnson

THE Lepanto Consolidated Mining Company is the largest copper producer in the Philippines, and the only one that makes a concentrate valuable principally for its copper; also, it has the only productive copper mine situated at considerable distance from the sea, and is the only one in the islands operating its own smelter. The Lepanto mine is in the Municipal District of Mankayan, sub-province of Benguet, near the heart of the Mountain Province of Northern Luzon. It is 165 km. from its shipping point at San Fernando, Province of La Union, on the shore of the China Sea. Elevations at the property range from 3200 to 4500 ft. The climate is very mild; temperatures are seldom below 50° or above 80°F. Annual rainfall approaches 170 in. and is mainly confined to a rainy season lasting from May to October. The months from December to April, inclusive, are usually extremely dry. This climatic pecularity entails the problems of landslides on the roads during the rainy season and water shortage during the dry season. The Mountain Trail, an improved rock-surfaced toll road maintained by the Commonwealth Government, gives access to the property. The 105 km. over this road may be traveled in about 4 ½ hr. during the dry season. Very few sections of the road are straight for more than 100 meters, and about one third of it is a one-way road controlled by gates. All freight for the property is delivered by the Manila Railroad Company to Bauang, La Union, 45 km. west of Baguio and at sea level, where it is picked up by freight trucks and hauled via Baguio to Lepanto. Granulated matte is hauled in bulk from Lepanto in four-ton lots on freight trucks to the storage bins at San Fernando. Freight rates from Bauang to the property amount to P8.00 per ton, and from the property to San Fernando the rate is P16.00 per ton. The company pays the road toll, P1.00 per truck, each way. THE CAMP The company maintains a modern camp, well separated from the mine and reduction plant. Comfortable and sanitary living quarters, water, and light, as well as free medical service are provided all employees. A hospital staffed by a doctor and two nurses takes care of all medical treatment. Considering recreational facilities of great importance, the company has provided two tennis courts, two basketball courts, and badminton courts for employees. Bowling alleys and a motion picture theater are operated by the company, the profits being expended for other recreational purposes. A moderate sized recreation hall serves for barrio dances, meetings,

Jan 1, 1942

By Raymond Mancha

When calculating the pressure-volume characteristics of projected mine-ventilating circuits by orthodox methods, certain basic assumptions are required in order to employ the various available empirical data. It is assumed, for example, that the mine air is an incompressible fluid subjected to isothermal flow, an assumption sufficiently accurate for practical purposes since pressure and temperature differentials are small throughout the average circuit. A more erroneous assumption, however, is that all air is accounted for as it travels throughout the mine. No attempt is usually made to evaluate stopping leakage as it occurs; instead, the air volume required at the last crosscuts is assumed to enter the mine, travel the various intake air courses intact, sweep the workings and travel out by the return air courses to the point or points of exit from the mine. Actually, there is a leakage of air from intake to return at every stopping, the quantity of this leakage depending upon the tightness of the stopping and the pressure difference across the stopping. Unfortunately, a lack of empirical data and knowledge of the condition of individual stoppings makes an exact analysis of underground stopping leakage impossible. Generally, leakage is most severe through the old stoppings outbye the circuit. These are also subjected to higher pressure differences than the newer inbye stoppings. Therefore the circuit air volume diminishes at a decreasing rate progressing from outbye to inbye the circuit. Consider a simple mine circuit consisting of one intake and one return air course, each of equal and uniform section area and interconnected at regular intervals with crosscuts equipped with stoppings. At any point X inbye the circuit the air volume q on the intake air course equals that on the return air course and decreases with diminishing rate from outbye to inbye the circuit between the limits of Q1 completely outbye and Q completely inbye. Such a volume change is represented by curve a, Fig. I, which is computed with the aid of the equation q = Q1- (Q1- Q)(X + L)N. This equation results from the general algebraic equation of form q = k, — kXN after solving for kl and k with the knowledge that completely outbye X = o and q = QL, also completely inbye X = L and q = Q. Curves a, b and c, Fig. I, show values of q as ordinates versus values of X as abscissas, for values of N equal to 0.50, 1.00 and 2.00, respectively. Distribution of underground stopping 1eakage directly affects the air-volume distribution along the circuit, which in turn determines the circuit pressure gradient. To deliver any required air volume inbye a circuit or portion thereof requires a higher circuit-pressure differential if stoppings leak than is necessary with tight stoppings. Every mining engineer engaged in the analysis of projected mine-ventilation circuits is therefore confronted with the problem of making proper allowance for the effects of leaking stoppings. The purpose of this paper is to present evidence in support of the author's suggestion that circuit pressure increase (per cent)

Jan 1, 1942

By Raymond Mancha

When calculating the pressure-volume characteristics of projected mine-ventilating circuits by orthodox methods, certain basic assumptions are required in order to employ the various available empirical data. It is assumed, for example, that the mine air is an incompressible fluid subjected to isothermal flow, an assumption sufficiently accurate for practical purposes since pressure and temperature differentials are small throughout the average circuit. A more erroneous assumption, however, is that all air is accounted for as it travels throughout the mine. No attempt is usually made to evaluate stopping leakage as it occurs; instead, the air volume required at the last crosscuts is assumed to enter the mine, travel the various intake air courses intact, sweep the workings and travel out by the return air courses to the point or points of exit from the mine. Actually, there is a leakage of air from intake to return at every stopping, the quantity of this leakage depending upon the tightness of the stopping and the pressure difference across the stopping. Unfortunately, a lack of empirical data and knowledge of the condition of individual stoppings makes an exact analysis of underground stopping leakage impossible. Generally, leakage is most severe through the old stoppings outbye the circuit. These are also subjected to higher pressure differences than the newer inbye stoppings. Therefore the circuit air volume diminishes at a decreasing rate progressing from outbye to inbye the circuit. Consider a simple mine circuit consisting of one intake and one return air course, each of equal and uniform section area and interconnected at regular intervals with crosscuts equipped with stoppings. At any point X inbye the circuit the air volume q on the intake air course equals that on the return air course and decreases with diminishing rate from outbye to inbye the circuit between the limits of Q1 completely outbye and Q completely inbye. Such a volume change is represented by curve a, Fig. I, which is computed with the aid of the equation q = Q1- (Q1- Q)(X + L)N. This equation results from the general algebraic equation of form q = k, — kXN after solving for kl and k with the knowledge that completely outbye X = o and q = QL, also completely inbye X = L and q = Q. Curves a, b and c, Fig. I, show values of q as ordinates versus values of X as abscissas, for values of N equal to 0.50, 1.00 and 2.00, respectively. Distribution of underground stopping 1eakage directly affects the air-volume distribution along the circuit, which in turn determines the circuit pressure gradient. To deliver any required air volume inbye a circuit or portion thereof requires a higher circuit-pressure differential if stoppings leak than is necessary with tight stoppings. Every mining engineer engaged in the analysis of projected mine-ventilation circuits is therefore confronted with the problem of making proper allowance for the effects of leaking stoppings. The purpose of this paper is to present evidence in support of the author's suggestion that circuit pressure increase (per cent)

Jan 1, 1942

By P. Marier, T. R. Ingraham

When anhydrous cupric sulfate is heated in a stream of nonreactive gas, cupric oxysulfate is formed. When this reaction is complete, the cupric oxysulfate then decomposes to cupric oxide, which is the normal end product of reaction. The kinetics of each of these reactions has been studied using pellets prepared from finely divided cupric sulfate and from finely divided cupric oxysulfate. In each case, the reactant-product interface within the pellet is well-defined, and by normalizing the decrease in inter facial area with the weight fraction of the pellet decomposed it has been shown that the interface migrates into the pellet at a uniform rate at constant temperature. The activation energy estirnated for the decomposition of cupric sulfate is 57 ± 7 kcal per mole and that for cupric oxysulfate is 67 ± 8 kcal per mole. The rate of interfacial reaction is flow-sensitive, increasing with increasing flow of a sweep gas in the range from 50 to 2000 cu cm per min. The rate of decomposition is retarded by sulphur trioxide in the sweep gas. The relationship between sulfur trioxide Partial pressure and rate is consistent with the Langmuir Adsorption Isotherm governing the retention of sulfur trioxide in the interfacial layer. MOST of the work reported on the thermal decomposition of cupric sulfate and of cupric oxysulfate is related to the thermodynamics of the individual decompositions.'-4 No information is available on the rates of the individual reactions, on their activation energies, or on the effects of gas flow or of partial pressure of sulfur trioxide on the reaction rates. Some dubious conclusions based on relative reaction rates have been drawn from studies on the oxidation of sulfides. For example, on the basis of the products observed in a quenched system, it has been suggested5" that, when copper sulfide is roasted, the cupric oxide which is formed arises from the decomposition of either cupric sulfate or cupric oxysulfate. This is very difficult to reconcile with the thermodynamics of the C-S-O System,3 which support the probability that both cuprous oxide and cupric oxide precede cupric oxysulfate and cupric sulfate in the sequence of products formed during the oxidation of cuprous sulfide. In this paper the individual sulfate decomposition reactions will be examined and suggestions will be advanced for the mechanism of reaction. This will be based on the effects on reaction rate of changes in interfacial area, flow rate, and back-pressure of sulfur trioxide. EXPERIMENTAL Materials. The copper source material used in all experiments was Fisher Certified Reagent Grade anhydrous cupric sulfate, for which the following analysis was supplied by the manufacturer: chloride, 0.002 pct; alkalies and earths, 0.2 pct; insoluble, 0.002 pct; iron, 0.020 pct. Cupric oxysulfate was prepared by roasting cupric sulfate for 48 hr, with frequent rabbling, in an open tray in a muffle furnace maintained at 725°C. At this temperature, cupric sulfate develops about 0.16 atm pressure of combined sulfur trioxide, sulfur dioxide, and oxygen. Cupric oxysulfate develops only about 0.05 atm pressure, and is stable until

Jan 1, 1965

By D. B. Jugle, J. B. Darby

The equilibrium solubility limits of the transition elements Ti, V, Cr, Fe, and Co in liquid tin were determined in the temperature range from 827" to 1211°K. Since the equilibrium concentration of Ti, V, or Cr in liquid tin is moderately dilute in the temperature range investigated, the solubility data were employed to estimate the partial molar enthalpy and the partial molar excess entropy of solution for the three solutes in liquid tin. The reference state s for titanium or vanadium were selected relative to the solute in an intermetallic compound. The thermodynamic quantities for chromium were calculated relative to pure chromium. RECENT experiments1 have shown that the rate of solution of several transition elements in liquid aluminum can be qualitatively predicted from a knowledge of the temperature dependence of the solvent-rich liquidus. In order to extend the analysis to binary tin systems,' it was necessary to know the equilibrium solubility of several of the first-long-period transition elements in liquid tin. Since solubility data for the tin-rich portion of binary systems are meager, the present investigation was undertaken to determine the equilibrium solubility limit of Ti, V, Cr, Fe, and Co in liquid tin in the temperature range from 850" to 1200°K. EXPERIMENTAL PROCEDURE A useful technique3 to determine the equilibrium solubility of a solute in a liquid-metal solvent consists essentially of placing a pure solute in contact with a pure solvent and allowing sufficient time for equilibrium to be attained at the temperature of interest. Subsequently, the solvent is removed and the equilibrium solute concentration in the solvent is determined by an appropriate analytical procedure. The technique can be applied very successfully to relatively simple systems such as the copper-germanium system.3 However, in many binary systems of transition elements with tin, several intermediate phases are known to exist and precipitation of the phases from solution, in solubility experiments, can lead to an erroneously large solubility. The difficulty was avoided in the present work by equilibration of the most solvent-rich intermediate phase with the pure solvent over a range of temperatures. The compounds employed in this investigation, and the temperature range over which each compound is in equilibrium with liquid tin are listed in Table I. No stable intermediate phases are reported in the chromium-tin system4 and, therefore, pure chromium was utilized as the solute. The stoichiometric compounds were prepared by arc-melting on a water-cooled copper hearth in a helium-argon atmosphere. The elemental tin employed in.this investigation was 99.998 pct pure, and typical lot analyses of the transition elements were reported elsewhere.' A sample of an appropriate solute, in the form of a button and in sufficient quantity to exceed the equilibrium solubility, and the pure tin solvent were placed in a high-purity recrystallized-alumina crucible. The crucible and contents were placed in a horizontal furnace under a high vacuum (10-6 torr) and held at temperature for periods varying between 24 and 72 hr. A water-cooled quench tank, partially filled with diffusion-pump oil, was attached close to one end of the

Jan 1, 1970

By H. C. Fiedler

Heats of high purity iron containing 3.1 pct Si and be -tween 0.0003 and 0.0295 pct N were prepared by vacuum melting ad then pouring while in a nitrogen atmosphere with the pressure between 0 and 90 psi. Strip from a heat with 0.0184 pct N underwent complete secondary recrystallization during the final anneal. Heats with less nitrogen had too few Si3N4 particles to restrain normal grain growth, and the heat with higher nitrogen had too many particles to allow complete secondary recrystallization. In the hot-rolled structure, Si3N4 precipitates only at the grain boundaries, with the consequence that annealing after hot-rolling diminishes the ability to subsequently undergo secondary recrystallization. In contrast to this behavior, ALNprecipitates uniformly in the hot-rolled structure. Under 1 atm of nitrogen, Si3N, in 3.1 pct Si-Fe dissociates between 900" and 950°C; the solubility of nitrogen increases from 0.0010 pct at 900" to 0.0030 pct at 1200°C. The solubility of nitrogen in Si-Fe has been the subject of many investigations. Corney and Turkdogan1 heated a 2.83 pct Si alloy in nitrogen and found the solubility, under 1 atrn of nitrogen, to be 0.0019 pct at 900°C. They claimed that Si3N4 did not form in the alloy above 705°C in 1 atrn of nitrogen. Fryxell et al.2 heated samples of 3.25 pct Si-Fe containing 0.0025 pct N over a range of temperatures and then analyzed for total nitrogen by vacuum fusion and for nitrogen in solution by a modified Kjeldahl technique. At 900°C, they reported the solubility of nitrogen in equilibrium with Si3N4 to be 0.0011 pct. pearce9 found the solubility of nitrogen at 900°C under 0.95 atrn of nitrogen to be 0.0017 pct in a 3.06 pct Si alloy. He reported that Si3N4 does not form above 770°C in 1 atrn of nitrogen. Although internal friction measurements have given somewhat higher values for the solubility,4-6 if the solubility of nitrogen is as low as has been reported by most investigators, and if Si3N4 is stable up to at least 945°C at 1 atrn pressure of nitrogen as reported by Seybolt,7 a small amount of nitrogen in properly processed Si-Fe should be effective in promoting secondary recrystallization. The requirement is that in the final heat treatment there be enough small, well-dispersed particles of Si3N4 to restrain normal grain growth. Fast8 has obtained secondary recrystallization by nitriding high-purity 3 pct Si-Fe after hot-rolling to a thickness of 0.118 in., followed by processing to 0.012 in., and annealing. A large amount of nitrogen, 0.076 pct. was introduced during the nitriding heat treatment, but he has since reported9 that "a few hundredths of a percent" is sufficient. Small amounts of aluminum10 or vanadium" nitride are capable of promoting secondary recrystallization. Heats containing as little as 0.010 pct A1 or 0.042 pct V and from 0.006 to 0.009 pct N underwent complete secondary recrystallization at final gage, whereas heats with lesser amounts of aluminum or vanadium did not.l2 To be reported is the behavior of nitrogen in high-purity 3.1 pct Si-Fe, and the relation of this behavior to the ability to undergo secondary recrystallization. PROCEDURE Ingots weighing 1 lb were made by vacuum melting high-purity electrolytic iron (A104, Glidden Co.) and high-purity silicon (Monsanto Co.). The latter was used in preference to ferrosilicon to insure a low aluminum content. The design of the melting furnace permitted pouring with the furnace atmosphere either below or above atmospheric pressure. Accordingly, at the completion of melting, nitrogen was admitted to the desired pressure and the heat then immediately poured. The ingots were sound, with no indication of porosity. In Table I are listed the heats investigated, the nitrogen pressure at pour, and the nitrogen and oxygen contents as determined by vacuum fusion with a platinum bath at 1850°C, a procedure which insures measurement of the total nitrogen.13 In addition, all heats contained 3.1 pct Si and not more than 0.002 pct C, 0.003 pct S or 0.005 pct Al. It was subsequently found that the quantity of nitrogen contained in the heats in Table I does not necessarily represent that obtained under equilibrium conditions. For example, the ingot poured immediately after 1 atrn of nitrogen was admitted to the chamber contained 0.0093 pct N, whereas an ingot poured 3 min after the nitrogen was admitted contained 0.021 pct N and another poured after a 6-min delay contained 0.029 pct N. While some bleeding of the hot top occurred in the latter instance, the ingot when examined in cross section appeared sound. The ingots were heated to 1325°C in hydrogen and rapidly rolled to 0.080 in. in 3 passes. The roll speed of the final pass was reduced so as to increase the quenching effect of the rolls. The hot-rolled pieces were processed both as-hot-rolled and after heating for 3 min at 900°C in hydrogen. After cold-rolling to 0.026 in., the strips were heated for 2 min at 900°C in hydrogen, then cold-rolled to the final gage of 0.012 in. The loss of nitrogen in going from the ingot to cold-rolled strip was no more than 10 pct. The final heat treatment, which was for the purpose of develop-

Jan 1, 1970

By L. C. Campbell

THE purpose of any accident-prevention program is the curtailment or entire elimination of injuries and fatalities. It is a job that is never finished in the coal-mining industry. Day by day, on shift and off shift, men are exposed to injury and death in varying numbers. Seldom is it possible to lock up at the end of the shift and leave a mine plant in the care of a sleepy watchman, as can be done at most manufacturing plants. Even on off shifts there are maintenance and supply crews, coal cutters, pumpers and ventilation men exposed to danger. The prevention program of The Koppers Coal Co. recognizes two primary facts: First, no program can be successful without the full support of the management and complete knowledge of the job at hand on the part of every supervisor. Second, and equally important, is the full cooperation of every employee in observing the safety rules and practices set up by the management. Conscious day-to-day concern for his safety by the indi-vidual worker is the longest stride toward a good safety experience. How to accomplish the education of the individual worker and super-visor for safety is the problem of The Koppers Coal Co. as it is the problem of all coal companies.

Jan 1, 1939

By P. Somasundaran, D. R. Nagaraj

This study initiated to explore the potential of commercial chelating extractant for beneficiation of minerals revealed "LIX "65N to be an excellent collector for cuprite and chrysocolla. The collector action of the LIX is proposed to result from its chelation with copper species on the surface of the minerals. Thus, the syn-isomer of LIX65N, which is unable to form a chelate with copper ions, failed also to act as a collector. The proposed mechanism takes into account partitioning of LIX between the mineral surface (to form a surface chelate) and the copper chelate dispersed in the bulk aqueous phase (either due to formation of the chelate with dissolved copper, or due to detachment of chelate formed at surface). The efficiency of the collection is dependent upon this partitioning since the bulk chelate is found unable to collect. The marked decrease in flotation obtained when copper was added to the system supports this mechanism. The dependence of flotation of chrysocolla and cuprite on pH and reagentizing time is discussed on the basis of the proposed mechanism. Batch laboratory flotation tests using synthetic mixtures of oxide, sulfide and mixed oxide-sulfide copper minerals with quartz demonstrated the ability of LIX to separate the copper minerals from quartz.

Jan 1, 1980

By William S. Dershowitz

INTRODUCTION Numerical methods commonly used in rock mechanics, such as finite element, displacement discontinuity, and boundary integral equation methods, offer solutions to problems which can be described by differential equations subject to boundary conditions. These numerical methods use approximations leading to solutions in terms of matrix algebra and numerical integration. Many rock mechanics problems which are beyond the scope of such approximations can be treated effectively by application of techniques developed in the field of artificial intelligence (AI). Among the possible applications are: site characterization (Duda, 1975), geological interpretation (Smith and Baker, 1983), solution of problems involving rock joint networks, and underground construction. Each of these applications utilize particular features of Al. Here we shall present results of AI applications which utilize primarily search and to lesser extent learning or pattern recognition. Specific examples presented are in the field of rock fracture network problems and underground construction. ARTIFICIAL INTELLIGENCE Artificial intelligence techniques attempt to achieve human-like reasoning and learning capabilities. This reasoning capability is valuable in applications where repetition, complexity, or tediousness makes human-like intervention impractical. In rock mechanics this occurs, for example, in stochastic rock mass modeling applications where some complex decision-making is required for each of a large number of iterations.

Jan 1, 1984

By L. S. Castleman, H. A. Froot

A study was made of the growth kinetics of B-brass layers in a-brass us y-brass diffusion couples in which both phases were saturated in the 6 phase. It was found that useful estimates can be made of the difhsion coefficients at the ß-phase interfaces from interface displacement data, which are relatively easy to measure experimentally; also, a useful estimate can be made of the mean heat of activation for diffusion from layer growth data. The effects of pressure on layer growth kinetics were explored and found to be consistent with a vacancy model for diffusion in 6 brass in both the disordered and ordered temperature range. 1 HE study of multiphase diffusion receives relatively little attention in comparison with that devoted to diffusion in homogeneous materials. Of the hundred or so papers on diffusion written each year,' only a few are devoted to the subject, and it is the rare review article2,3 that devotes any space to multiphase diffusional phenomena. This is unfortunate, since the metallurgist frequently encounters practical situations involving cementation processes such as cladding, protective coating of metals, and so forth in which he needs guidance of a fundamental nature. The investigation of multiphase diffusion phenomena is complicated by the fact that one must consider reactions at phase interfaces as well as the migration of atoms within the individual phases; these reactions cause the interfaces to be displaced within the diffusion zone. The relative displacement of two adjacent interfaces corresponds to the growth of an intermetallic layer, and it is not difficult to determine experimentally the kinetics of layer growth. In the past few years it has been pointed out4,5 that valuable fundamental information may be gained about diffusion coefficients and the concentrations at interfaces through a study of their motion. Accordingly, it is the purpose of this paper to report the results of an investigation of interface motion in a simple multiphase binary system. In the work reported herein, attention was focussed on the growth of a 6 -brass layer in a diffusion couple prepared from a- and y-brass compositions saturated with respect to the 6 phase. This particular system was chosen for a number of reasons. First, the bcc ß-brass phase is disordered for all compositions at temperatures above 468°C and becomes increasingly long-range ordered for all compositions at temperatures below 454° C;6,7 thus, the effects of a variation in order on interface displacement could be determined. Second, diffusion coefficients have already been obtained as a function of temperature in the ß phase both in the ordered and disordered Re- and a theoretical picture of the mechanism of diffusion in this and other ordered solutions is emerging.11'12 Third, some thermodynamic data are available for the a-, ß-, and ?-brass phases,13,4 and these data could be used to gain insight into questions of phase equilibria and concentrations at phase interfaces.

Jan 1, 1963

By G. E. McElroy

THOUGH air jets occupy only a minor role in the ventilation of mines and other enclosures, their importance in this respect is greater than is commonly recognized and may be considerably increased as our conception of their modes of operation becomes clearer. The object of this paper is to discuss some of the ways in which air jets are involved in mine ventilation and some possible applications to the ventilation of mines and other enclosed spaces. The mention of air jets ordinarily suggests the use of some form of an air injector, such as the Venturi blower occasionally used for auxiliary ventilation in mines, or the Saccardo (injector) system used to a limited extent for ventilating railroad tunnels. Actually, the term covers such common phenomena as the discharge of air from fan pipes and coal-mine line brattices, and even from smoke stacks and fans. A knowledge of the general mode of air entrainment by jets also helps to explain certain phenomena-some mine-gas explosions, for instance-that otherwise would remain obscure. Jet action has been involved in three recent series of Bureau of Mines experiments in which the author has participated: experiments on fan-pipe discharge, on the dilution of gases discharged from a stack and on the ventilation of a ship's hold. Available data on the discharge of jets into large openings and on the design and performance of air injectors have been analyzed in considerable detail and supplementary experiments are planned for after the war. The results of the fan-pipe experiments have been combined with the analyses of data on jet discharge into large spaces, and have been published.1 The results of the stack-gas dilution tests, which refer to a jet discharged into a crosswind, have also been published2 and a paper on the design and performance of injectors has been prepared for publication.3 These technical experiments and analyses form the background and the documented evidence for the following nontechnical discussion of the use of air jets in mine ventilation. JET CHARACTERISTICS The jets commonly encountered are those in which the air is in turbulent-as opposed to laminar, or streamline-motion. The characteristics under discussion apply only to such turbulent jets and have their basis in theories of the mixing of turbulent air currents. Such jets have basic characteristics that are present, though variable in form, regardless of whether the jet expands freely in space, whether the expansion is limited by adjacent walls, or whether the jet propels air through a flow circuit. They expand at definite angles and entrain the surrounding air, even though the entrained air must be obtained by recirculation of their own air streams. As the quantity of air in motion in the mixed stream increases, the average velocity of the stream decreases. In the case of entrainment in the free

Jan 1, 1945

By R. F. Shurtz

This paper relates geostatistical doctrine to classical statistical and mathematical concepts. It is not a contribution to geostatistics; it is a contribution about geostatistics. It uses descriptive and pictorial arguments to assist interested readers in forming an intuitive grasp of the recondite and difficult mathematical issues involved. The method chosen is to cite authoritative literature references from the two fields and trace connections between them. Four broad conclusions appear: first, geostatistics comprises a relabelled subset of concepts detached from classical statistics and mathematics; second, this relabelling artificially isolates geostatistics from the classical fields and restricts its scope; third, the classical fields still have much to offer to the mining industry but will remain fallow unless artifcial communication barriers are removed; and fourth, the unique advantages asserted for geostatistics are neither unique nor necessarily real. These findings should not be regarded as iconoclastic but rather as Pointing the way to a wider and more productive scope for those who evaluate mineral deposits.

Jan 1, 1983

Within the last century, and largely during the latter half of it, the increase of our knowledge of the development of man, both in his search for a livelihood and for power, and in the growth of his reason and conscience, has been greater than all we had known before. The great interest in all kinds of archaeological work and the many excavations made of buried and long forgotten places has put at our disposal historical records not available, and in many cases not known before, and a study of these and other records of human progress from paleontological and geological sources has given us a much broader view of what we call "civilization" than was possible even a short time ago. The old idea that men were created with fully developed minds, speech and reason has yielded to the view that in the upward progress of the human race the development of the mind and reason has been a comparatively recent occurrence, as we think of the half million, and probably more, years that have passed since our earliest records of man were made. The traits that come to us without effort

Jan 1, 1935

By C. W. Waidner

THE standard scale of temperature that it is attempted to realize in practice is the centigrade thermodynamic scale, as defined by Kelvin about the middle of the last century. This scale would be exactly realized with a perfect1 gas in an ideal gas thermometer, and is closely realized with the more permanent gases. From the departure of certain properties of these gases from those of a perfect gas, it is possible to deduce the amount of the departure of the temperature scales, defined by their use, from the thermodynamic scale. In nearly all the precise experimental work done during the latter part of the last century, it was necessary for the experimenter to establish his own gas-thermometer scale, and the labor involved in this was often greater than that involved in the prime object of the experimental work undertaken. The experimental difficulties involved in gas thermometry led to the establishment of temperature scales differing from one another by amounts considerably greater than could be accounted for by the differences in the properties of the gases used. Results were, therefore, expressed in terms of somewhat different temperature scales, snaking correlation of such results difficult and uncertain.

Jan 9, 1919

By John V. Beall

Given: One large, but dated open-pit copper mine and processing plants, down about one third in production capacity in decade because of declining ore grade. Solve for: Restoration of former peak capacity without further losses during period of reconstruction. That is the problem that Kennecott's Utah Cop- per Division began solving in 1963. Most of the work went to a task force of engineers, several of whom were plucked out of line jobs and assigned to the so-called "Expansion Project" for the duration. There was no doubt from the beginning that effective cooperation between Expansion Project engineers and operators was critical to success, and personnel was chosen accordingly. This foresight paid off. The Expansion Project is all but complete, and the Utah Copper Division is returning to its rated capacity of 300,000 tons per year of copper metal.

Jan 6, 1967

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

ONE of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing of the A.S.T.M., 1938. The work of Mann,1 Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserve especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by [P OL, plotting So = Ao as a function of eo = Lo] where A o and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors' It was shown that the true physical behavior of the material in the tension test could best be represented [by plotting the average true stress, S = P as a function of e = q' = log o = log Log] where P, A, L, S, e, and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximum load point to fracture. The construction of such- curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain difficulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece

Jan 1, 1941