Search Documents

By W. F. Carew, F. A. Crossley

The stress for rupture in 500 hr at 1000° F has been reported to be about 13,000 psi higher for Widmanstitten than for equiaxed microstructures for the Ti-7A1-3Mo alloy.1,2 Also, limited data indicated Widmanstatten and equiaxed micro-structures to have approximately the same creep resistance at 1000°F.' Recently, data have been obtained which show Widmanstatten structures to be significantly more creep resistant than equiaxed structures at 1000°F, see Fig. 1. These data represent several ingots and several heat treatments of the solution treat and age type. The thermal history and tensile properties corresponding to the creep data are given in Table I. The creep data were taken from creep-rupture tests. The associ- ated rupture data are given in Table 11. It may be noted that total creep deformations are considerably greater for equiaxed structures. Previous evaluations of stability indicated that all of the structures tested are stable with respect to exposure to stress at elevated temperature.1,2 For a minimum creep rate of 10-4 in. per in. per hr the difference in stress levels is indicated to be about 17,000 psi. Holden,et found an irreversible contraction upon heating three a-ß titanium alloys in the equiaxed condition above their ß-transus temperatures. The alloys were: Ti-6Al-4V, Ti-155 A (5Al-1.3Cr-1.5Fe-1.2Mo), and C-130 AM (44-4Mn). The net contractions in length between the original equiaxed and the final Widmanstatten structures measured at room temperature were: 0.4, 0.4, and 0.7 pct, respectively. The greater creep and rupture resistance of the WidmanstStten structure of the Ti-7Al-3Mo alloy may be associated with the phenomenon

Jan 1, 1959

By E. W. Greene, J. B. Duke

This paper deals with the application of froth flotation techniques to the beneficiation of kaolin clay and phosphate slimes, two very fine particle sized materials. The kaolin problem involves the removal of a small amount of a contaminating mineral (anatase), while the phosphate problem involves the concentration and recovery of a much larger percentage of apatite. Due to these differences, and also different response to flotation, the two problems are discussed in separate parts of the article. An idea of what is meant by "Ultrafine Minerals Or Slimes" as used in the title can be had by an examination of Fig. 1. Particle size distributions are presented for a crude kaolin clay, a coarse fraction and a fine fraction. The crude kaolin as mined was blunged with water, degritted through a 325-mesh Tyler screen, and dispersed with sodium silicate. The dispersed crude was then centrifuged in the laboratory into the coarse and fine fractions shown in the figure. The distribution curves were obtained by the well known sedimentation technique of Casa-grande1 using a long arm centrifuge to obtain equiva- lent spherical diameters down to 0.2 p on the finer fraction. Fig. 1 shows the coarse fraction kaolin to be 50% finer than 3 p, while the crude kaolin is 509 f'lner than 1.4 p, and the fine fraction 50% finer than 0.46~. For comparison 53 p on the horizontal scale would represent Stokesian diameters which would just pass a 325-mesh Tyler screen, taking into consideration the Andreasen sieve correction factor of 1.22 times the screen opening. 2 Another helpful comparison is the surface areas, which in square meters per gram, are 0.044 for 53 p particles, 0.77 for 3p, 1.65 for 1.4 p and 5.0 for 0.46 p particles. Fig. 2 is an electron micrograph of a similar fine fraction kaolin showing the hexagonal plate-like particle shapes.

Jan 1, 1962

By W. Rostoker

IN the course of the development of the phase equilibrium diagram for the system Zr-Cr,' the structure of an as-cast allov having the composition ZrCr2 was analyzed and established to be isomorphous with MgZn2 (C14, hexagonal lattice, 12 atoms per unit cell). In a recent paper on the same system, Hayes, Roberson, and Davies' report for the ZrCr2 phase an isomorphy with MgCu2 (C15, cubic lattice, 24 atoms per unit cell). It appeared that this conflict might be resolved by assuming a high and low temperature modification for ZrCr2. That this was the case with the phase TiCr2 has recently been demonstrated by Levinger." Specimens of ZrCr2 annealed at 1200°, 1100°, 994", 900°, 834", 800°, and 700°C, respectively, and subsequently quenched were examined by X-ray diffraction analysis. It was successfully demonstrated that a transition from the MgZn, structure at lower temperatures to the MgCu, structure did occur at some temperature between 900" and 994°C. Table I lists the observed structures at the various annealing temperatures. In Table II, a summary of line spacings and intensities is given for each of the allotropic modifications. The first six lines of the MgCu2 structures have been located in the table to illustrate the close similarity between the patterns. Lattice parameters of the two modifications were calculated by a least squares solution of equations for interplanar spacings for a series of high angle lines. The results are as follows: MgZn2 type - c = 8.262 kX, A = 5.079 kX. MgCu2 type — a = 7.195 kX. It is interesting to note that TiCr2 behaves in reverse fashion yn that the MgCu, structure is the low temperature modification and the MgZn2 structure is the high temperature modification. References lR. F. Domagala, D. J. McPherson, and M. Hansen: This issue p. 279. 'E. T. Hayes, A. H. Roberson, M. H. Davies: Trans. AIME (1952) 194, p. 304; Journal of Metals (March 1952). 3B. W. Levinger: Trans. AIME (1953) 197, pp. 195-196; Journal of Metals (February 1953).

Jan 1, 1954

By Paul H. Lu, Fred D. Wright

Numerous laboratory tests and field measurements conducted by different persons have indicated that most mine rocks behave viscoelastically rather than elastically. Hence, for an accurate and realistic design of underground structure, the time factor should be taken into account, and the theory of viscoelasticity can be used. By considering the time factor, the time-safe-strength may be used for economical design instead of liberal safety factors with design based on the elasticity theory. The deflection and moment distributions on an elastic roof slab resting on elastic pillars have already been studied.l In this chapter, the stress- strain analysis for a viscoelastic mine roof resting on pillars of the same material or on supports of different material is first considered theoretically. Viscoelastic solutions for deflections, moments, and shears are de- rived from the elastic plate theory on the basis of the elastic-viscoelastic correspondence principle. The Laplace transformation technique is employed as the operational method in the mathematical treatment. The roof slab materials are represented by four different rheological models and four different loading histories are considered. The method of finite difference equations is employed for solving the partial differential equations, using FORTRAN programs to calculate roof deflections, moments, and shears. Numerical examples are given for one of the four models under two of the four loading histories with regular and staggered pillar patterns. The results are discussed in terms of the variance with time of deflections, moments, and shears as well as their variation in space due to the dimensions and configuration of the structure system. A viscoelastic slab resting on viscoelastic pillars or on elastic supports

Jan 1, 1972

By S. C. Lee

An uncoupled thermoviscoelastic finite element formulation with an application to Underground Coal Conversion (UCC) is presented. An incremental solution procedure with an implicit time stepping scheme is used under the thermorheologically simple material (TSM) postulate. The presented formulation, for a homogeneous and isotropic medium, is employed in the simulation of the UCC post-burn phase. Temperature, displacement, stress, and failure responses under thermomechanical loading are predicted. The solutions for the selected field problem indicate potential roof collapse, stress relaxation, and modest surface subsidence with a progressive thermal and failure front. The corresponding thermoelastic responses with temperature- dependent elastic properties are also presented and compared with the thermoviscoelastic results.

Jan 1, 1984

By W. N. Marchant, P. T. Brooks, P. B. Altringer, R. O. Dannenberg

The US Department of the Interior, Bureau of Mines conducted laboratory tests to devise a process for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 ppm W (70 ppm W03). Using ion exchange resins synthesized by USBM chemists, 98% oft he tungsten was extracted from the brine and 92% of the tungsten was recovered as a marketable iron-tungsten concentrate containing 44% tungsten as tungsten trioxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process research unit to provide more reliable data for an economic appraisal.

Jan 8, 1979

By Rudolph G. Wuerker

Charles T. Holland (Head, Dept. of Mining Engineeri*, Virginia Polytechnical Inst., Blacksburg, Va.) Mr. Wuerker has presented a very interesting discussion of the use of triaxial test methods for investigating the strength properties of rocks. Such methods, no doubt, eventually will develop considerable information of interest to those concerned with the design of mine layouts, particularly in the field of pillar design. From his discussion of my recent article, "Cause and Occurrence of Coal Mine Bumps" (Holland Mining Engineering 1958, p. 933-1002), it is evident that in one place at least I did not make my meaning clear to him and perhaps others. To clear the matter up I think it best to quote from the article, somewhat more fully than did Mr. Wuerker, as follows: "4) In actual operations — because rocksare not perfectly elastic, homogeneous, nor isotropic and because local yield does occur — the maximum stress as demonstrated by Phillips (Ref. 22, pp. 64, 65) and indicated by much experience in mining, does not occur at the walls of the opening but at a short distance inside the pillar. Furthermore, the maximum stress does not reach as great a value as theoretical considerations and laboratory experimental methods indicate.* Actual distance inside the pillar, measured from the wall, at which the maximum stress exists, has not been determined. Observations in many mines, however, indicate that this distance could have a mini-value of one to six or eight times the bed thickness and that it is probably affected by width and height of the opening, depth of cover, and relative values of the elasticity and plasticity of materials comprising the roof, floor, and coal seam. The actual value of the stress produced probably lies between the theoretical maximum and the average stress concentration that would be produced if the weight of the strata above the unsupported opening were evenly distributed over the pillars for a distance equal to the opening width." The footnote reference in the above quotation referred to the following: "*For example, the Pocahontas No. 4 coal bed in southern West Virginia is mined under cover up to 1800 ft thick. Development openings are driven 18 to 20 ft wide, and the bed is about 6 ft thick. According to the work of Panek, the tangential wall stress at mid-bed height under these conditions would reach values between 4000 and 5000 psi. Actual tests of 3-in. cubes of this coal show its compressive strength would be much less than this, perhaps as low as 400 psi. Yet the pillars usually show no evidence of failure in these headings. In this same bed at a depth of 800 ft, the author has seen an opening 225 ft between supports lying between two old groves approximately 1100 ft apart. According to the theoretical considerations, the stress in the pillar walls would have been about 18,000 psi, yet the pillar showed little or no evidence of weight. In view of these observations, it is clear that the wall stress does not attain the maximum values indicated by theory." (Underlining added to original wording.) By referring to Fig. 2A of my paper it will be noted that theoretically the maximum pillar stress would occur at the pillar wall, i.e., at the passageway surface of the pillar. Obviously this cannot be correct in the cases of stress ranging from 4000 to 18000 psi since the coal at the surface of the pillar is under no constraint and cannot have a strength much greater than 400 or 500 psi. Hence, my conclusion that the maximum stress does not occur at the wall but back in the pillar some distance from the wall. Since these stresses are pushed back in the pillar from the wall, it is also obvious that the loads transferred to the pillar from the opening will be spread over a greater area and hence Pillar stresses will not rise to the values postulated by theory and photoelastic experiment. Further since to visual inspection the coal along the pillar wall did not appear to be failed the conclusion was reached that the stress shift was caused by local elastic or plastic yield and by difference in the elastic modulus of the rocks composing the mine floor, mine roof, and coal bed. Later on under the heading "Strength of Mine Pillars" (pages 1000-1002) the effects of constraint is briefly described. Also a formula taking into account constraint is developed relating pillar strength to the uniaxial strength of coal and the L/T ratio of the pillar. Since my paper was written, reports of experiments conducted in South Africa (Denkhaus, et. al., 1959), in Sweden (Hast 19581, and in Canada (McInnes, et.al., 1959) reveal that the conclusion expressed relative to the existence of a low stress area existing around the edges of pillars and solid faces as described above is generally correct. But it seems possible that where the wall stress developed is less than the unconfined strength of the rock composing the pillar and where the roof, floor, and pillar

Jan 1, 1961

By M. J. Spendlove, H. W. St. Clair

The problem frequently arises, particularly in refining metals or smelting scrap metals, of separating metals in the metallie state. Many metals may be separated by taking advantage of their difference in vapor pressure. Such separations can be made at atmospheric pressure, but the separations are much more selective and can be carried out at considerably lower temperatures if the distillation is done at pressures of a few millimeters or less in an evacuated enclosure. Until recently, this has not been considered feasible as a metallurgical operation, but the recent improvemcnts that have been made in vacuum technology have broadened the applicability of vacuum processes and have prompted re-examination of low-pressurc distillation of metals as a practicable process. The distillation of zinc from lead is one separation that has already been reduced to practice.l This paper is the first of a series of studies being made on separation of nonferrous metals by distillation at low pressures. Although these experiments were confined to the separation of zinc from aluminum, the significance of the results is by no means confined to these two metals. The purpose has been to investigate a metallurgical technique rather than merely to devise a means of separating specific metals. The experimental work on distillation of zinc from zine-aluminum alloys at reduced pressure grew out of earlier work on distillation at atmospheric pressure.2 The earlier work indicated that it would not be practicable to decrease the zinc in the alloy much below 10 pct owing to the high temperature required. Therefore attention was turned to distillation ah low pressures, at which lower temperatures are required. After preliminary tests were made in a small, evacuated tube furnace, a larger furnace having a capacity of 100 to 150 Ib of metal per charge was constructed. Distillation tests were first made on pure zinc and then on aluminum-zinc alloys of various composition. Particular attention was given to the limit to which zinc could be reduced in the residual metal. Data were also taken on the rate of evaporation, and heat balances were made for both the crucible and the condenser. Distillation Furnace The vacuum-distillation unit is illustrated schematically in Fig 1. The major components are the induction furnace, the condenser, the vacuum system, and the power-conversion unit. Power is supplied to the induction furnace from a 50-kw 3000-cycle motor-driven alternator. The pressure in the furnace is reduced by a vacuum pump having a nominal pumping speed of 10 liters per sec. When in operation, the metal vapors travel upward from the furnace to the water-cooled condenser where they are collected in amounts of 50 to 100 lb. The condenser is removed with aid of an electric hoist. When the system is under vacuum, the condenser is made self-sealing by a rubber gasket between the smooth-faced, water-cooled flanges at the top of the furnace and the bottom of the condenser. The pressure of the atmosphere is more than sufficient to insure sealing. At the conclusion of an experiment, the residual metal can be removed from the furnace by removing the condenser and tilting the furnace with the electric hoist. The metal was cast into the molds carried on a mold truck. A photograph of the furnace and auxiliary equipment is shown in Fig 2. The details of the vacuum furnace are illustrated in Fig 3. The furnace proper is made vacuum-tight with rubber gaskets placed at each end of a fused quartz cylinder. A clamping plate at the bottom and a ring at the top are made to squeeze the rubber between the metal and the end of the quartz tube. A large graphite crucible placed inside the quartz cylinder is thermally insulated and physically supported by refractory insulating bricks. A thermocouple in a quartz protection tube is located at the bottom of the crucible: the leads pass through a rubber seal in the bottom plate. The supporting structure for the furnace is an angle iron frame with transite board sides. The condenser is made in the form of a water jacketed cylinder with an opening to the vacuum line at the top. The bottom has a projecting skirt inside the machined flange to provide additional cooling for the rubber gasket. Condenser sleeves are made in the form of two semicylindrical pieces of sheet metal that fit snugly inside the cooling jacket. The split sleeve facilitates removal of the condensate. Measurement of Temperatare and Pressure The metal temperature was measured by a platinum-platinilm rhodium thermocouple inserted in a well extending up into the bottom of the graphite crucible. During rapid evaporation there is a wide difference in temperature between the surface and the main body of metal in the crucible because of the large amount of heat that must be conducted to the surface to supply the heat of evaporation. The heat of

Jan 1, 1950

By Edward Pesout

The McGill smelter started operations in the year 1907. The smelter furnaces were fired with run-of-mine coal on grates until April 1911, when oil firing was introduced. Oil firing continued until April 1918, when the initial coal-pulverizing plant was started.' Early Pulverizing Plant Various alterations were made to that plant during its operation, one of the more important being in connection with the system for delivering pulverized coal. In order to minimize coal-dust explosions and fires, the return portion of the main delivery line was eliminated in the year 1928. Thereafter coal-dust explosions and fires were greatly reduced. Pulverized coal was prepared at this plant primarily for the reverberatory furnaces, but for several years it was also delivered to the converting plant, roasters and power-plant boilers by a system of auxiliary fans and delivery lines. During the period March 29 to April 8, 1929, one reverberatory furnace was fired with pulverized coal produced by an Aero, type J, unit coal pulverizer with a rated capacity of 5 tons per hour. This machine actually pulverized its rated capacity but the product was too coarse. After certain regulations, a her product was obtained but the pulverizer capacity decreased and this resulted in insufficient coal for efficient furnace operation. Table I gives a comparison of the average screen analyses of the pulverized-coal products from the impact-type unit pulverizer and the regular coal-plant installation. It was definitely proved that this size and type of unit pulverizer could not furnish sufficient coal of proper fineness to give smelting results comparable to that obtained with the regular coal-pulverizing plant. The coal from this unit pulverizer was so coarse that it did not ignite or burn properly and thus did not produce the proper heat for efficient smelting. During the latter part of 1929 and the early part of 1930, experimental work was conducted with a 7-ft. o-in. by 48-in. Hardinge conical ball-mill coal-grinding unit, which was installed alongside a furnace in the reverberatory building. Results obtained from the test run indicated that this unit would furnish sufficient coal of proper fineness for good smelting.

Jan 1, 1947

By Robert Craig, Earl L. Rau

Introduction Grinding circuits are used to reduce the particle size of ores to the size desired for beneficiation or to grind a concentrate to a size required for final marketing. Grinding and classification can be carried out using either wet or dry circuits. Most sulfide ores are ground in wet circuits using one or more stages of grinding to obtain the necessary mineral liberation to produce a final concentrate which will meet the desired criteria. Iron ores are ground in circuits applicable to the particular ore using either wet or dry grinding. Nonmetallic minerals frequently present different requirements. Barite is likely to be subjected to wet grinding before beneficiating the ore; the concentrate is dried and then dry ground to meet market particle size requirements. The one thing that most mill operators will agree to is that there is no such thing as the "best" configuration of equipment for grinding. The circuit which works well on one ore may be totally unsatisfactory for another ore body. The general trend in the industry is flow sheet simplication with fewer parallel circuits instead of multiple-line circuits using small mills. This change in philosophy has been brought about by the saving of both capital and operating costs that may be possible with larger equipment. Remember that comminution is basically a very inefficient process, and that the costs can range upwards to 50% of the total milling costs. It, therefore, behooves the mill operator to carefully design his grinding and classification circuits. He must ascertain the optimal economic particle size for beneficiation and then make certain he has achieved the best balance between capital and operating costs to achieve the desired mesh of grind. Equipment Grinding circuits consist of one or more pieces of equipment to grind the solids. Generally, these circuits include one or more grinding mills, classification equipment, and the necessary materials handling equipment such as pumps, pipelines, and conveyors. There are many different types of equipment available which are used to grind and classify ores and minerals. Following is a tabulation of most of the equipment used for wet and/or dry grinding.

Jan 1, 1982

By W. F. Holbrook

IN a previous paper1 a method for the measurement of the comparative desulphurizing power of slags was described and data were presented covering the range of likely slags containing up to 10 per cent MgO In the present work the range is extended to include slags containing up to 20 per cent MgO, and the effect of temperature on 5 per cent and 15 pen cent MgO slags over the range 1475° to 1525° C is included The method used was that described in the previous paper except that some of the temperature measurements were made with a noble-metal thermocouple instead of a tungsten-graphite thermocouple Twelve-gram charges of 0 8 per cent sulphur-metal and 5-gram charge-, of slag were subjected to heating for 30 nun at a prescribed temperature The charges were analyzed for sulphur content For purposes of comparison, desulphurizing power is defined as the ratio of the percentage of sulphur found in the slag to that found in the metal Six slag and metal charges were made coincidentally in 5/8-in holes in a section of an electrode graphite rod One slag and metal charge was used as a control by means of which adjustment in the desulphurization value could be made for small variations in temperature and other factors For convenient presentation of the data, the slags are arranged in groups in each of which one of the four main slag components is constant Thus, the 15 per cent MgO slags are presented separately from those containing 20 per cent MgO SLAGS WITH MAGNESIUM OXIDE CONSTANT 15 Per cent MgO -The data on slags containing 15 per cent MgO cover a composition range of 24 to 50 per cent SI02, 5 to 27 per cent A1203 and 24 to 53 per cent CaO Variation in composition has been in steps of 2 per cent over much of the area Because the change in desulphurization power is generally gradual with gradual change in composition, certain sections have been covered m steps of 4I per cent and even

Jan 1, 1938

By R. A. Swalin

IN this paper, the results of an investigation concerning the diffusion of three elements, magnesium, silicon, and molybdenum, in nickel are presented. The work represents a continuation of a diffusion program relating to solute diffusion in nickel. The program has the dual aim of obtaining useful diffusion data and of yielding insight into the factors governing solute diffusion in close-packed metals. The first paper of this series has been published earlier? In both investigations, in agreement with recent results from other laboratories, the activation energies for solute diffusion were found to be close but not identical to that of self-diffusion in the pure solvent in question. In order to obtain valid diffusion data, certain experimental pitfalls recognized only in recent years had to be avoided. Chief among these were the necessity for minimizing short-circuiting diffusion paths such as grain boundaries and the necessity for using low solute concentration gradients. In this series of investigations the following precautions were taken in an attempt to minimize such errors. 1) Samples with large grain sizes, 0.5 to 10 mm, were prepared. 2) The diffusion coefficients were measured at relatively high temperatures, since imperfections such as dislocations play a less important role at such temperatures than at lower temperatures. 3) Alloys containing less than 1 atomic pct were chosen for study. Experimental Work Materials—A diffusion couple technique was employed in the experimental investigation. Briefly, this technique consisted of the following. A diffusion couple was fabricated by placing a flat face of a cylindrically shaped alloy disk against a similar face of a pure nickel disk, and a bond was formed at an intermediate temperature under pressure. The diffusion couple thus fabricated was subjected to a diffusion anneal at higher temperatures for a measured period of time and then sectioned perpendicular to the direction of diffusion. After analyzing the sections for solute concentration the diffusion coefficient was determined from a probability, plot of concentration vs distance from the diffusion interface. Vacuum melted Mond nickel was used in the experimental program. The chemical analysis of this nickel is listed in Table I. Alloys used were prepared

Jan 1, 1958

By Thomas F. Downing

When examining a coal property it is customary for the engineer to take channel samples at several coal faces. In doing so the extraneous matter, or partings, which can be removed by hand, or mechanically, with the facilities at hand, or proposed, is rejected. Where there is doubt concerning a stratum it is usually rejected from the main sample but part is taken for separate analysis. The samples are forwarded to a chemist for proximate analyses and determination of British thermal units, and, sometimes, ash fusion. Consideration is given all available commercial analyses but frequently the owner presents only the favorable ones. From the results thus obtained a general evaluation is made, monies are loaned or expended, markets are determined, and realization is estimated. In many instances, such grades are not substantiated and it is time we looked deeper for a basis which will prove more practical. Institute committees are working hard on analytic and use classifications and much valuable information has already been assembled and distributed. However, no single grade can be applied to any particular bed or region. Much study has been given the Pittsburgh No. 8 seam, yet that bed is subject to material differences in a single section;i. e., some strata of a face may differ from others in structure and analysis, particularly in sulfur content. From some localities it yields a good carbonization fuel, while in others it is chemically unfit for such use. Traveling south to the Logan, W. Va., field we find the Cedar Grove (Island Creek) seam a hard, gray splint coal., In the same field, and not far distant, the same bed changes, both structurally and chemically, and consists of excellent gas coal. In Illinois the moisture content of a bed may vary greatly in different localities. We have seen mines in which part of the coal is excellent for special purpose use but is spoiled by the product from another part of the same mine. Many other illustrations could be given but these are sufficient to show that application of any grading of coal must be distinctly local. The actual designation of grade can be given only after detail study of the component parts of the seam, or seams, on the property under considera-

Jan 1, 1932

By Edward Pesout

The McGill smelter started operations in the year 1907. The smelter furnaces were fired with run-of-mine coal on grates until April 1911, when oil firing was introduced. Oil firing continued until April 1918, when the initial coal-pulverizing plant was started.' Early Pulverizing Plant Various alterations were made to that plant during its operation, one of the more important being in connection with the system for delivering pulverized coal. In order to minimize coal-dust explosions and fires, the return portion of the main delivery line was eliminated in the year 1928. Thereafter coal-dust explosions and fires were greatly reduced. Pulverized coal was prepared at this plant primarily for the reverberatory furnaces, but for several years it was also delivered to the converting plant, roasters and power-plant boilers by a system of auxiliary fans and delivery lines. During the period March 29 to April 8, 1929, one reverberatory furnace was fired with pulverized coal produced by an Aero, type J, unit coal pulverizer with a rated capacity of 5 tons per hour. This machine actually pulverized its rated capacity but the product was too coarse. After certain regulations, a her product was obtained but the pulverizer capacity decreased and this resulted in insufficient coal for efficient furnace operation. Table I gives a comparison of the average screen analyses of the pulverized-coal products from the impact-type unit pulverizer and the regular coal-plant installation. It was definitely proved that this size and type of unit pulverizer could not furnish sufficient coal of proper fineness to give smelting results comparable to that obtained with the regular coal-pulverizing plant. The coal from this unit pulverizer was so coarse that it did not ignite or burn properly and thus did not produce the proper heat for efficient smelting. During the latter part of 1929 and the early part of 1930, experimental work was conducted with a 7-ft. o-in. by 48-in. Hardinge conical ball-mill coal-grinding unit, which was installed alongside a furnace in the reverberatory building. Results obtained from the test run indicated that this unit would furnish sufficient coal of proper fineness for good smelting.

Jan 1, 1947

By S. W. Kennedy, M. Cohen, L. D. Calvert

A high-temperature X-ray diffraction method has been used to study the composition and the kinetics of formation of oxide scales at 800 °C on iron and pure iron-nickel alloys containing 25.6, 75, and 84 pct Ni. This technique has been combined with chemical analysis, and metallographic examination, and determination of weight-gain time curves. The 75 and 84 pct Ni alloys form a three-layer scale consisting of porous NiO next to the metal, a spinel layer, and a -Fe203 on the outside. The 25 pct Ni alloy produces a scale of spinel and Fe,O,, in which, however, traces of FeO and NiO are observed near to the metal. On all the nickel alloys the Fe20, is orieqted with the (107) plane parallel to the surfaces. The exposed surface of the Fe20, is in the form of needles whose axis is perpendicular to the specimen surface. Although the alloys show nonuniform oxidation rates as determined from weight-gain measurements, the X-ray data indicate that the total scale and individml scale layers grow uniformly and parabolically. Deep subscale formation is observed in the 25 pct Ni alloy only. This appeared to be associated with cracking of the scale and penetration of the oxygen along the grain boundaries. ALTHOUGH film formation has been investigated by high-temperature electron-diffraction techniques, for example by Gulbransenl and Hickman,' there have apparently been no investigations of scaling by methods permitting study of the scale during formation at the reaction temperature. Methods involving quenching of scales are based on the working assumption that no significant changes take place on cooling. In general, however, compounds may disproportionate, and the different thermal expansions of constituents may cause disruption of the scale on cooling. In particular, some scales cannot be quenched without spalling. These difficulties are avoided by X-ray diffraction examination at the temperature of formation. High-temperature diffraction procedures also provide a method of determining the kinetics of formation of each phase separately in a multicom-ponent scale. The scaling of binary iron-nickel alloys Containing up to 30 pct Ni at a temperature of 800°C has been studied by Benard and Moreau using cooled specimen~,~ whilst Foley, Druck, and Fryxel14 made an electron-diffraction study of cooled oxide films formed on an iron 42 pci Ni alloy. In the present work the scaling of three iron-nickel alloys containing 25.6, 75, and 84 pct by weight of nickel, at 800°C in oxygen at atmospheric pressure was investigated by X-ray diffraction techniques using a Norelco Geiger-counter diffrac-tometer. The oxidation of iron was investigated for comparison. In addition normal metallographic examinations and chemical and X-ray analyses were made, and weight-gain time curves obtained. EXPERIMENTAL Materials Used—The analyses of the alloys were as follows: Percent by Weight Nickel 25.6 pct 75.4 pct 83.2 pct Aluminum 0.004 None found 0.002 Cobalt — 0.05 0.05 Chromium — — — Silicon — 0.01 None found Carbon All less than 0.05 pct The chemical analysis of the iron was: Al— 0.002 i 0.001 pct, C—0.007 pct, Cr less than 0.001 pct, Cu—0.002 ± 0.001 pct, Mn—0.003 ± 0.001 pct, N—0.0002 pct, 0-0.013 pct, P—less than 0.0002 pct, Pb—not detected, S—0.0017 pct, Si—0.0095 pct, Sn—none detected. This iron was the same as that used to make the alloys and was obtained from the same source-Vacuum Metals Corp. One specimen of pure iron from The British Iron and Steel Research Association was used for preliminary investigation. Specimens were machined to shape from cast rod, polished (the final polish being with 600 Sic paper), degreased in trichlorethylene, washed, and etched. The etching and neutralizing procedure adopted by

Jan 1, 1960

By H. I. Aaronson, C. Laird

Although the past results of X-ray experiments indicate that the broad faces of 0' plates are coherent with their matrix, dislocations lying in arrays have frequently been observed at these boundaries by transmission electron microscopy. Critical experiments employing the latter technique have been carried out in order to determine the origin of these dislocations. It is concluded that 8' plates are essentially coherent with the matrix at their broad faces throughout the aging temperature/time envelope studied. Virtually all of the dislocation arrays observed are deduced to have been formed by plastic deformation accompanying transformation. The proportion of dislocations arising from convexity of the plates is shown to be negligible by comparison with that from plastic deformation. At the higher aging temperatures, a[001] dislocations appeared in moderate numbers. These dislocations were traced directly, however, to the ledgewise dissolution of 0' occasioned by the formation nearby of 0 crystals. On the other hand, since there is a parametric difference normal to the broad faces of the ?' plates, mismatch dislocations do form at their edges. A previous conclusion that these dislocations have Burgers vectors of type a[001] was confirmed directly. The edges of 0' plates were observed to develop octagonal shapes when growing, but circular shapes during dissolution. 1 HIS paper presents the results of an investigation of the interfacial structures of plates of the transitional phase, 8', formed in an A1-4 pct Cu alloy. In a companion paper, Part 11, the effects of these structures upon the migration kinetics of a:?f boundaries are reported. This work is pa.rt of a general program designed to establish the basis of precipitate morphology. The present authors in Al-Ag,1 and whitton2 previously in U-C alloys, have used transmission electron microscopy to examine directly the vander Merwe3-6 networks of dislocations anticipated7 to compensate the small amount of lattice misfit normally founda at the broad faces of Widmanstatten plates. Since the broad faces of 0' plates are considered to be perfectly coherent with the corresponding habit planes in the a matrix,' no dislocations should be present at these faces. Many reports have been published, however, giving evidence to the contrary.10-18 The primary objective of this investigation was therefore to ascertain the nature of these dislocation structures. An attempt to do this is described in the first three sections of this paper. Inspection of the matching of the a and 8 ' lattices at the orientations of the 0:0' boundary corresponding to the edges of 0' plates raises the possibility that these edges may be made up of rather closely spaced edge- type misfit dislocations oriented so as to be sessile with respect to the lengthening or shortening of the plates. Since this structure should severely inhibit migration of the plate edges (Ref. 7, Part II), a situation not originally anticipated,' an experimental determination of the interfacial structure of the edges of 8' plates was clearly in order, and is reported in Section III. Those aspects of the experimental procedure applicable to both Parts I and I1 are presented in the next section. Specific procedures applicable to individual aspects of each investigation, and also the relevant surveys of the literature, are then individually reported in the appropriate sections. I) GENERAL EXPERIMENTAL PROCEDURE The material used in both parts of these studies was the same as that of a previous investigation:" strips of A1-3.93 pct Cu, 0.009 in. thick, prepared as before, solution-annealed at 548°C for 6 hr, and quenched. Details of subsequent aging, and in some cases deformation treatments, are given in the Experimental Procedure sections of the individual parts of both papers. Specimens of the heat-treated strips were electro-thinned as beforeLg and examined in a Philips EM 200 microscope equipped with a goniometer stage. A commercial hot stage, of the grid-heater type and capable of * 30-deg tilt about one axis in the plane of the specimen, was also used for kinetic studies. The usual precaution of calibrating for the additional heat supplied by the electron beam was taken.19 A 16-mm cine cam-I era mounted outside the viewing window was frequently used to record the transformations. Conventional selected-area diffraction and dark-field viewing techniques were used to identify the precipitates in the foils. Normal bright-field images corresponding to two-beam diffracting conditions or dark-field images were employed to characterize the dislocations observed at the interfaces of the precipitates. The application of these techniques to the study of an interphase boundary, and the interpretation of the images,20'21 has been fully described in a previous paper.'

Jan 1, 1969

By R. M. Schuller, J. J. Suloway, W. F. Childers, R. A. Griffin, S. J. Russell

Seven solid wastes from coal conversion processes were characterized chemically and mineralogically. The wastes included three Lurgi gasification ashes, two liquefaction residues (SRC and H-coal), a fly ash, and a water-quenched slag. Leachates generated from the solid wastes at various pH levels over the range 2.5 to 11.0 were analyzed for over 40 constituents. Results of the leachate analyses demonstrate the wide variation in constituent solubility for the solid wastes. To help assess the environmental impact of the disposal of these wastes, the leachates were also employed in soil attenuation studies and acute 96-hr static bioassays using young fathead minnows.

Jan 1, 1981

By Ned Kuenhold

AN equipment manufacturer swallows a bitter pill when he sees his machinery improperly in- stalled and not used to the full potential. This frequently happens with vibrating screens. Screens can be classified according to the path of vibration imparted to the screen surface. On this basis there are: 1) vertical circle or modified circle throw, 2) horizontal circle or modified circle throw, 3) vertical linear reciprocation, 4) tilted linear reciprocation, and 5) horizontal linear reciprocation. The most versatile vibration for medium to coarse sizing is generally conceded to be the vertical circle produced by an eccentric or unbalanced shaft, but other types of vibration may be more suitable for certain screening operations, particularly in the finer sizes.

Jan 6, 1957

By John J. Stokes

Literature on the electrolysis of aluminum from cryolite melts and on the structure of these .melts is surveyed critically. Data on density, freezing point, and other properties are reviewed. Theories of the electrolysis are examined in the light of these data. Two theories are presented which account equally well for the observations. In the early days, the process was thought of as a simple one. The actual mechanisms must be tremendously more complex. This paper is devoted to a rather narrow part of the whole subject, namely, what ions are present in the bath, and by what mechanism the current is carried. Using cryoscopic data, Rolin has determined the following composition for molten cryolite. Na2,AlF 3Na + 3F + AlF [1] He postulates the following equation for the ioniza-tion of alumina at low concentrations Al2O3 Al + AlO2 +O. [2] At concentrations above 0.025M he supposes the ionization of alumina to proceed as follows Al2O3 AlO + AlO2. [3] Rolin's mechanism of electrolysis for the more concentrated solution in Eq. 3 is as follows. The AlO' ion migrates to the cathode. where it is dis- charged, giving metallic aluminum and 0' ions which migrate to the anode. The AlO2- ion migrates to the anode, where it is discharged, giving Al ions and oxygen which reacts with carbon to form CO2 In the case of the extremely dilute solution in Eq. 2 the Al ion migrates to the cathode and the AlO2-and 0 migrate to the anode as before. Another possible mechanism for the electrolysis follows. Ionization of Cryolite Na3AlF4 = 2Na + 2F + NaAlF, Na + AlF-AlF+Na + F [4] Addition of Alumina 2Na2AlF+ 2AL2O4 6Na + 3A12O3F4 [5a] Al2O2F 2AlOF2 [5b] Cathode Process AlF, + 3e+ 4F + Al. [6] Anode Process AlOF2 + 2F AlF1 + 1/20, + 2e or A12O2F + 4F-2A1F; + 0, + 4e. [7] Although both Rolin's and the present mechanism of the Hall process may be qualitatively satisfactory, present data are not adequate for quantitative tests of the theories.

Jan 1, 1959

By R. D. Hagni

The following is a case study illustrating the use of thin sections and polished sections of crude ore to predict metallurgical response. By examining polished sections of the metallurgical products, the textural and mineralogical reasons for unsatisfactory separation can be explained. An area of oxidized Negaunee Iron-Formation located south of Negaunee, Michigan, in the Marquette Iron Range, has been considered for roast reduction-magnetic separation. Preliminary metallurgical studies and subsequent pilot plant testing produced varied results. These results prompted this microscopic study which began with an examination of 126 thin sections and 82 polished sections prepared from 126

Jan 1, 1967