Search Documents

By J. E. Burke

THE origin of so-called annealing or recrystalli-zation twins in face-centered-cubic metals continues to be a matter for speculation, and in the present report an attempt is made to explain their origin and to account for at least a majority of the observations concerning their behavior. The fact that annealing twins are prominent only The speelmen was deformed 8 pet in compression and then indented over the lower left-hand corner in a Rockwell in-denter, and then annealed to cause partial recrystallization. Note intense twinning in heavily deformed part and slight twinning in less deformed part. The upper right-hand corner is unrecrystalized. Area reduced approximately 25 pot for reproduction. after recrystallization suggests that deformation may be necessary for their formation. In 1926, Mathewson1 reported the observation by Phillips that annealing twins are frequently parallel to strain markings which delineate octahedral planes in the deformed (and partially recrystallized) matrix, and suggested that strain markings are mechanical twins which grow into annealing twins during recrystallization. Later work by Burke and Barrett' has shown that strain markings are traces of planes upon which slip has occurred, and that there is no evidence for the formation of mechanical twins of microscopically resolvable width in face-centered-cubic metals. Mathewson3 has pointed out, however, that slip may produce twin faults, and later modifications of this hypothesis have assumed that twin faults rather than true mechanical twins serve as the nuclei for annealing twins. Carpenter and Tamura5 suggested, also in 1926, that annealing twins might form by accidents of growth. A close-packed layer of atoms can be added to the octahedral plane of a face-centered-cubic metal in two possible positions, the right position

Jan 1, 1951

By Kent A. Pease

Design methods for foundation anchors and sockets constructed in rock are based largely on empirical correlations which yield a reasonable estimate for initial capacity, but do not address the general concerns of failure mode and load-displacement behavior. This paper focuses on the behavior of foundation-rock interfaces and shows that interface behavior under increasing load results in a progression from an elastic response to secondary behavior, in which interface failure occurs, and finally to a residual stage at large deformations. Procedures to follow this progression are outlined to provide a more fundamental understanding of the problem.

Jan 1, 1984

By H. R. Hanley, Charles Y. Clayton

One of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experimenting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must, be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive scries of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect on tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1943

By Newell Alford

THE data in this paper were collected to show both the volume and speed with which bituminous mines have indefinitely suspended operation while economic advantage in the industry has so gravely declined. The study was limited to the bituminous coal-mining states east of the Mississippi River, wherein conditions affecting production and demand are more common respectively to all of the mining districts included and represent about 95 per cent of the nation's coal mining. Data for the compilation of these statistics and for the construction of these graphs have been obtained in all cases from state mine depart-ment reports, except from those of Ohio and Virginia. In Virginia essential individual mine data were secured from an authentic source, but no individual Ohio mine information is obtainable, because all Ohio fact-gathering agencies are prohibited by law from revealing such data. In other states the facts were tabulated and later checked with the cooperation of Chief Mine Inspectors. In all, excluding Ohio, over 17,000 individual annual mine returns were examined. Special infor-mation was secured from each state mine department about suspensions in 1932. Accurate information was not available from all states about mine abandonment due to exhaustion of coal reserves, and while these were completed for several states, it has not been shown because it was not perfected for all states. However, the total observed sample was comprehensive enough to show that exhaustion accounts for a very limited part of the suspended production. Wherever mention is made of "suspended production" the largest annual output of the mine in the five years prior to suspension has been taken as the measure of its probable production had it continued to operate. A mine is not regarded in this category, as having suspended, when it merely ceases to produce. The word "suspension" is used only where there is a complete abandonment of activity for an indefinite period, as evidenced by the fact that both ventilation and pumping are discontinued.

Jan 1, 1933

By H. R. Hanley, Charles Y. Clayton

One of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial development in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experimenting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must, be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive scries of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect on tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1943

By Wilbur Nelson

Little drilling has been done in Kentucky and Tennessee in 1923, with the exception of the Kettle Creek area on the Kentucky-Tennessee line. Oil prices fluctuated between $2.86 and $1.36 Per bbl. for light oil. The Kentucky production was slightly over 8,000,000 bbl., being 1,000,000 bbl. less than during 1922. Tennessee production was approximately 8500 bbl., being a decrease of 1000 bbl, over. 1922. During 1923, the first producing well was brought in, in Clay County, Tenn. Production in Tennessee will undoubtedly increase considerably in 1924, and Kentucky production will probably increase slightly. THE year 1923 has been a dull period in oil development in Kentucky and Tennessee, with the exception of the Kettle Creek area along the Tennessee-Kentucky line, in Clinton and Cumberland Counties, Kentucky, and Clay County, Tennessee. The price of oil during the year has been so low that wildcatters have shown little interest in drilling. At the beginning of the year, light oil sold for $2.31 per barrel and medium oil for $2.06 per, barrel. Prices increased to the highest point for the year in February, when light oil brought $2.86 per barrel and medium oil, $2.61. In April, prices had declined 35 c. while in May an additional decline of 25 c. went into effect. During June, prices declined 20 c. per barrel; during July, 45 c. per barrel; remained stationary during August and September, and dropped during November and December to the low price of $1.36 per barrel for light and $1.21 for medium oil. At present, an increase of 29 c. has brought the price of light oil up to $1.55, and indications are that the price will continue to increase during the coming months. It can readily be seen that during 1923 the price of oil was such as to prevent any drilling except that necessary to hold leases and to maintain production enough to take care of overhead expenses.

Jan 3, 1924

By Robert B. Fulton

Commercially, celestite (SrSO4) is the predominant strontium mineral. Among other strontium-bearing minerals, only strontianite (SrCO3) occurs commonly; however, it is rarely an item of commerce. Production of celestite is principally in Mexico, Spain, and Turkey. An attempt to produce celestite in Canada was unsuccessful. The United States, which is wholly dependent on imports, chiefly from Mexico (99%), is the largest consumer of strontium. Lesser quantities are consumed in Japan and Europe. The Federal Republic of Germany is the principal source of strontium compounds imported to the US. Uses The principal uses of strontium are for the manufacture of strontium carbonate and nitrate. Carbonate is used in glass for TV tube face plates and in ceramic ferrites for magnets. Nitrate is used in pyrotechnics, mainly in safety flares, to which it imparts a characteristic brilliant red color. Minor amounts of strontium compounds are used in electrolytic zinc manufacturing where the carbonate is used to remove unwanted lead. Small quantities are consumed in greases, ceramics, soaps, alloys, and pharmaceuticals. Specifications Typical celestite specifications for the carbonate and nitrate markets are shown in Table 1. Specifications of manufactured carbonate, sold in two grades, one to the glass industry and the other for ceramic ferrites, are shown in Table 2. Both grades of carbonate are shipped in palletized 50-lb bags. Glass grade material is shipped in bulk by rail. [ ] Manufacturing Processes The following description is adapted from Anon. (1980) . The manufacturing process for strontium carbonate and strontium nitrate chemicals is conceptually simple. Strontium nitrate is made from strontium carbonate in two additional steps. The production process begins with celestite, the natural form of strontium sulfate. In the first step the ore is crushed, ground, and mixed with coke. This mixture is then fed into a kiln where the ore is reduced at high temperatures to strontium sulfide; the coke is added to the ore as a source of energy and carbon. The carbon combines with the oxygen [ ]

Jan 1, 1983

By H. R. MacMichael

THE rate, at which zinc ore can be sintered varies widely, depending on the characteristics- of the ore. A coarse table concentrate already roasted to a very, low sulfur content may sinter at the rate of-8.6 tons per hour per 100 sq.ft., of wind-box area. At the other extreme is a finely ground flotation, concentrate, with considerable sulfur remaining in the ore as delivered to the sinter plant, for which corresponding rate may be only 3.8 tons per hour, or 44 per cent of the first rate. A usual, size-of sinter machine in zinc plants is one with wind-box 3.5 by 33 ft., making 115.5 sq. ft. of area, and using a 100-hp. fan. Such a machine with the coarse concentrate described would produce 10 tons of sinter per hour; and with the fine, flotation concentrate would produce only 4.4 tons per hour. Ore of the latter class is -sintered at the plant of the Mexican Zinc Co. (subsidiary of the American Smelting & Refining Co.) at Rosita, Mexico. ; Consequently, an unusually large sintering capacity per ton of ore to be treated is required, and provision was made for treatment of 9000 tons concentrates per month, preroasted to. 5 to 9 per. cent sulfur. For this duty three of the usual 33-ft., 100-hp. sintering machines would have been needed.. Considering the auxiliary equipment. necessary for proportioning, handling, and mixing charge, as well as means for disposition of the sinter, a three-unit plant becomes-very complicated, especially if the capacity should be doubled later. After much study it was decided to build a single sintering unit of ample capacity for the work, the plant thus being much simpler and cheaper in construction as well as in operation (Figs. 1 and 2). The sintering machine was built with a wind-box 5.25 by 60 ft. (315 sq. ft.) and provided with a 300-hp. fan.

Jan 1, 1932

By Peter J. Huck, Madan M. Singh

IIT Research Institute has investigated the potential of high pressure water jets for rapid rock excavation. During this study, an attempt was made to correlate the extent of breakage effected to the mechanical properties of rocks. Six rock types were used in these experiments and nine properties were determined for each rock variety. A regression equation using the two most significant rock properties and one jet parameter (pressure) was established. Although tests were conducted to specific pressures of 35, no minimum in the specific energy consumption was noted.

Jan 1, 1971

Percussion drilling with tungsten carbide insert button bits ranks among the most significant advances in both underground and surface drilling in medium and hard rock formations. Getting top performance and life from these upfront components is not particularly difficult if one pays attention to the basics in operation and maintenance. For some reason, a few of the essential operating and maintenance steps for getting the most from these tools seem to have gotten turned around; instead of operating at the near optimum levels, some miners, in following myths or misunderstandings about them, are shortchanging their optimal utilization. Let's examine the two most harmful ones.

Jan 8, 1978

By C. W. Kovach, A. Moskowitz

Studies were undertaken to investigate the effects of manganese content on the machinability and other Properties of a free machining martensitic stainless steel (AISI Type 416). Machinability was found to be significantly improved in steels of high manganese content, and a direct relationship was obtained between machinability and steel Mn:S ratio. As the manganese content of the steel increases, the sulfide Phase present changes from CrS to (FeMn)Cr2S4 to (MnFeCr)S, and finally to MnS. The average sulfide inclusion hardness decreases through the same range of increasing manganese content. The mechanism for machinability improvement is discussed in terms of a soft ductile sulfide affecting deformation in the secondary shear zone. Type 416 containing relatively high manganese for improved machinability shows good general properties. The effects of increasing manganese content on mechanical properties, cold formability, and corrosion resistance are described. THE addition of sulfur is commonly used to improve the machinability of stainless steels. However, little attention has been paid in the past to the composition and characteristics of the sulfur-containing phase or phases present in these resulfurized steels. Recent information on the properties of sulfide phases, and their role in metal cutting, suggests that variations in these phases could have critical effects on machin-ability, as well as important effects on formability and other properties such as corrosion resistance. Manganese, chromium, and iron are strong sulfide forming elements present in stainless steels! of these, manganese has the greatest sulfide forming tendency and iron the least.1"1 The manganese content of resul-furized 13 pct Cr steels, often about 0.5 pct, can be insufficient or only barely sufficient to combine with the sulfur that is present; thus, the precise level of manganese can strongly influence the nature of the sulfide phase. Sulfide phases which may be present in stainless steels have been reported to include CrS, a spinel-type sulfide, chromium-rich manganese sul-fide, and manganese Sulfide.5,6 Detailed phase relationships for the Fel3Cr-Mn-S system have been reported by the present investigators,7 and a portion of this work will be referred to subsequently in this paper. Recent work by Kiessling6 and Chao et a1.8 has shown that sulfide phases can display wide variations in hardness, and may undergo considerable plastic deformation under isostatic loading.9-12 Early theories of metal cutting attributed the influence of sulfur to a lubricating effect. It is now apparent that the influence of the nonmetallic inclusions and their properties on crack initiation, deformation in the shear zones, and boundary films must also be considered in relation to the machining process. This paper presents the results of studies conducted to relate machinability to the various sulfide phases which occur in stainless steels. This work has led to the development of alloys with improved machinability, and has generated information on the effects of inclusions on metal cutting processes. Effects of sulfide inclusions and steel composition on other important metallurgical properties are also discussed. MATERIALS For drill machinability and inclusion studies, 10 lb laboratory heats were melted in an air induction furnace. These heats were made with sulfur contents be tween 0.10 and 0.50 pct and manganese contents be tween 0.05 and 3.0 pct. Residual elements were added to the heats in amounts typical for commercial steels. The typical compositional range covered by the heats is shown below: C Mn P S Si Ni Cr Mo Cu N 0.10 0.05 0.007 (M0 0.40 0.40 13.0 0.20 0.10 0.03 3.0 0750 The laboratory ingots were forged in the temperature range of 1800" to 2100°F to 3/4-in. sq bars, and all bars tempered to a hardness aim of 200 Bhn prior to testing. Because of differences in composition and tempering response, the tempered bars showed some variation in hardness (175 to 275 Bhn) as well as variations in delta ferrite content (0 to 50 pct). Composition, hardness, and delta ferrite content were considered in the analysis of the machinability data. Additional tests involving tool-life evaluation and determination of other properties were conducted on materials from commercially melted and processed 15-ton electric furnace heats. TESTS AND PROCEDURES Machinability of the laboratory heats was evaluated in a drill test. In this test, 1/4-in. diam holes, 0.4 in. deep, were drilled alternately in a test bar and in a standard bar for a total of four holes in each. This sequence was repeated three times using a freshly sharpened drill each time. The average time required to drill a hole in the test bar was compared to that for the standard bar. A drill machinability rating was assigned to the test bar relative to a rating of 100

Jan 1, 1970

By Carl R. Davis

The cost of mining during the past history of these mines has been excessive, principally by reason of the inefficiency of labor under the wage-system. The amount of labor performed per man was unsatisfactory; and Mr. Edmund B. Kirby, the general manager, decided to adopt the contract-system as a remedy. For this purpose the method now in use was devised by the writer (then and now the superintendent), as best adapted to the local conditions. On March 12, 1900, this system was presented to the miners of the War Eagle and the Center Star. The issue remained unsettled for several weeks,

Jan 1, 1902

By C. L. Prokop

A laboratory investigation has been made of the effects of mud hydraulics upon the formation and erosion of mud filter cakes. The tests were conducted to simulate drilling conditions as nearly as possible. The formation of mud filter cake in a drilling well does not proceed at a uniform and unbroken rate. Instead, the rate of cake accumulation depends upon whether or not the mud is being circulated. If the mud column is quiescent, filter cake formation is a smooth function of the filtration characteristics of the system. If the mud is being circulated filter cake formation depends not only upon the filtration characteristics of the mud but also upon the erosive action of the flowing mud column Filter cakes formed during continuous mud circulation were observed to reach an equilibrium thickness after several hours' circulation. Mud circulation was maintained at a constant volumetric rate throughout each experiment. The fluid velocity at equilibrium cake thickness was dependent upon the thickness of the filter cake. Muds having exceptionally high water loss deposited thick filter cakes in spite of very high eroding velocities. The muds having good filtration characteristics deposited thin filter cakes at equilibrium circulating velocities well within tile range of those in a drilling well. It was observed that filter cakes deposited during stagnant filtration were quite difficult to erode by mud circulation. The - rate of crosion computed from the rate of filtrate accumulation after equilibrium cake thickness had been reached was in reasonable agreement with the rate of erosion obtained by direct observation. Continuous mud circulation usually caused the permeability of the filter cake to decrease with time. INTRODUCTION Many of the difficulties encountered during tile drilling of a well have been attributed to the loss of water from the mud and the attendant deposition of solids upon the walls of the hole. Past experience has shown that a reduction of the filtration rate of the drilling fluid eliminates or greatly reduces these difficulties. Definite filtration requirements, however, are hard to establish for a given set of conditions. This is due. in part, to the fact that the usual filtration test performed upon mud doe? not simulate well conditions as closely as desirable. The filtration characteristics of a mud are customarily determined by means of the standard low-pressure API wall-building tester.' In this instrument a filter cake is deposited upon a horizontal bed under a pressure differential of 100 psi. The rnud is quiescent during the filtration period. In actual practice. mud filtration occurs within a well under quite different conditions. One of the major differences is that mud flows upward across the filter bed as the filter cake forms. This undoubtedly produces a change in the filter cake which cannot be reflected in the results of the API test. The laboratory work described in this paper had as its primary objective a better understanding of the influence of mud circulation upon the thickness and ,characteristics of the filter cakes deposited under conditions similar to those existing in a drilling well. ANALYSIS OF PROBLEM Once a permeable formation is penetrated by the bit, filtrate from the mud flows into the formation. 'he mud solids plaster against the walls of the hole, forming a filter cake. If the mud column is stagnant, that is, if it is not being circulated. the filter cake will increase in thickness until the hole is filled. Prior to the time that the hole is filled, the thickness of filter cake existing at any given time will be a function of the filtration characteristics of the mud, the temperature, and the pressure differential. The effects of these variables have been investigated in the past for both flat bed filtration2'3 and for radial filtration.' When the mud is circulated in a hole in which a filter cake i. being deposited. some of the solids that would ordinarily deposit in the filter cake will be carried away by the eroding action of the mud. This will limit. filter cake thickness. Some work has been done to determine the effect of flow upon the filtration rate in a circulating mud system' but little work has been done upon the factors which determine the filter cake thickness existing in a circulating system. On first sight it would appear that the major factors controlling filter cake formation in a circulating system should be: 1. The rate of deposition of solids from the mud. 2. The erosive force that the flowing mud exerts upon the filter cake. 'A. The erodabilitv of the filter cake. 4. Any change in filter cake characteristics attributable to the scouring action of the mud. The rate at which solids are deposited from the mud will be controlled to a large degree by the filtration characteristics of the mud, the pressure differential. the temperature under

Jan 1, 1952

By H. A. Gardner

THE principal use of barium sulphate is as an inert paint pigment.. For this purpose, the ground material is used both in its natural and in its artificial forms. Probably the largest amount is used in the production of a chemically precipitated pigment called lithopone which consists of 70 parts of barium sulphate and 30 parts of zinc sulphide. An enormous tonnage-of this pigment is at the present time being used in the manufacture of interior flat wall paints of the oil type, such paints having almost entirely supplanted the use of corroded white lead which was at one time used for interior painting. The more dense nature, lower price and sanitary value of lithopone was responsible for this change. Lithopone is, moreover, used to a large extent in the manufacture of oil cloth, shade cloth and linoleum. Its whiteness makes it of particular value for this purpose. Barium sulphate is also used of itself in admixture with other pigments in the manufacture of prepared paints. The chemically precipitated form of barium sulphate, which is generally called blanc fixe, is also used for this purpose. Much controversy has raged in the paint world over the question of inert pigments such as barytes, silica, asbestine and china clay. These pigments are probably called inert because they have no chemical action upon the linseed oil in which they are ground to produce paints, and on account of the fact that they become transparent in oil. It is well known that in the manufacture of paints, opaque white pigments, such as basic carbonate white lead, basic sulphate white lead, zinc oxide etc., are generally used as the grinding base. These base pigments, when ground in oil, react therewith to some slight extent, and they produce white paints which have excellent biding or obscuring value. The inert pigments so-called, when ground in oil and spread out into a thin film, form transparent coatings which have no hiding power. It has been contended, therefore, that the use of barytes or similar inert pigments in paints is resorted to simply for the purpose of cheapening the cost of the product.

Jan 9, 1914

By D. N. Dietz

A method for determining average reservoir pressure is presented, which is simpler to apply than that devised by Matthews. Brons and Hazebroek. For bounded reservoirs, identical results are obtained if stabilized-flow conditions prevail. The present method yields inferior results in the transient state. The method can, with a slight modification, also be used for water-drive reservoirs. INTRODUCTION In the method proposed by Matthews, Brons and Haze-broek' for determining average reservoir pressure in a multi-well reservoir, the cumulative production (the production time of each well) enters twice: once when the buildup is plotted against In (t + t)/At to arrive at p*, and a second time when the correction, p*-p is determined with one of the several formulas for differently shaped drainage areas. Once a steady state has been attained, however, the previous production history should be immaterial. The same pressure distribution could have been arrived at after different cumulative productions of the individual wells. In principle, therefore, it should be possible to determine average pressures without referring to cumulative productions. In the following paragraphs an expression is presented for the difference between the pressure in a producing well and the average pressure of its drainage area. Then the build-up time needed to overcome this difference is indicated. CASE OF A CIRCULAR DRAINAGE AREA AND A CENTRAL WELL PRESSURE DISTRIBUTION BEFORE SHUT-IN The general differential equation of radial flow (see Muskat, Eq. 10.2) may be written In the steady state, the rate of production of the well is equal to the rate of expansion of the fluid contained in the the drainage area; thus

Jan 1, 1966

By Pradeep K. Rohatgi, David N. French, Surendar M. Jain, Clyde M. Adams

The effect of solute concentration and diffussivity on dendritic solidification of dilute binary aqueous solutions has been investigated; chlorides of sodium, potassium, lithiurn, and hydrogen were used as solutes. Dendrite spacings were measured in spherical droplets and in unidirectionally solidified specimens. In the droplets, the freezing rate is uniform over the entire specimen and remains constant from the beginning to the end of solidification. In the unidirec-tionally frozen specimens the freezing rate varies within a given volume of liquid during the solidification cycle; in addition, it varies with location uithin the specimen. Mass transport analysis has been used to calculate the supersaturation, AC, supercooling, AT, and transcerse growth velocity, V , of ice dendrites during solidijication from the dendrite spacings measured in the droplels. The ice dendrite spacing in a given solute increases lineary with the solule concentralion at a fixed freezing rate. The ualues of AC, AT, and V increase with an increase in solule concentration. The value of AT in the aqueous solution is of the same order of magnitude as in Al-Cu alloys of the same concentration; the dendrite spacings in Al-Cu alloys also increase with an increase in solute concentralion. For the jamily of aqueozrs solulions incestigaled, the dendrite spacing increases linearly with solute diffusivity at fixed values of concertralion and freezing ,rate. The values of ?C and ?T decrease, whereas the value of V increases with an increase in solule diffusicity. The measured dendrite spacings , L, can be expressed by the relatiun: L = K;(dfa/db) 4 K2C +K3D - K4 where dfs/d? is-change in fraction solid with time (freezing rate), C is solute concentration, D is solute diffusivit K1 = (14 * 4)pmin1'2, K2 = (70 ± 10) pl (moles)- K3 = (24 r 3) . l05 psec (cm)-~. K. = -132 ± 10) 1. FREEZING of solutions is almost always an ehunmix-ing" process because the composition of crystallizing solid generally differs from that of the parent liquid. " Solute concentration and transport are therefore in]portant considerations in solidification of solutions. The influence of these factors on the dendritic solutions produced from metallic solutions is of practical significance since the properties of the solid aggre-gate are often strongly influenced by dendrite spacing.''' Alexander and Fthines3 found that dendrite spac- ings generally increase with solute concentration in several metallic systems. Michael and Bever1 have observed an increase in a aluminum dendrite spacings in dilute A1-Cu alloys. Rohatgi and AdamsJ have reported a linear increase in a aluminum dendrite spacings with increasing copper contents up to 28 pct in A1-Cu alloys. Bolling and Tiller"' have theoretically examined the effects of solute concentration and diffusivity on the growth of cells and dendrites. Their analysis of dendritic growth assumes a steady-state growth and the maximum possible velocity for dendrite propagation. In addition, the quantitative analysis is restricted to dendrites of rotational symmetry and is therefore not directly applicable to the plate-shaped dendrites of ice obtained in the present study. There are practically no experimental observations of the effect of solute diffusivity on dendrite spacings in metallic systems. The reason appears to be the lack of experimental data on solute diffusion coefficients in liquid metallic solutions. The present work is concerned with the effect of solute concentration and diffusivity on dendritic solidification of dilute aqueous solutions: the solutes examined are potassium chloride. sodium chloride, lithium chloride. and hydrogen chloride. There were several reasons for selecting these solutes. The variation of dendrite spacing with freezing rate in these solutiolls is similar to that observed in A1-Cu alloys.8 These aqueous solutions have almost identical phase diagrams at dilute concentrations. Fig. 1. and the diffusion coefficients show very little variation with solute Concentration.9,10 Dendrite spacings were measured as a function of freezing rate. solute concentration. and solute diffusivity. Dendrite spacings were measured in two different types of freezing systems. droplet and unidirectional, respectively. In the droplet freezing system

Jan 1, 1970

By Robert E. Green, Robert A. Swanson

Ultrasonic attenuation and stress were measured simultaneously as a function of strain for aluminum single crystals tested in compression. The propagation mode and polarization of the ultrasonic waves were chosen with reference to the theoretical analysis presented in Part I. Good experimental agreement was found with this theory and with earlier experimental work in tensile tests. Support is given to the contention that ultrasonic -attenuation measurements are much more sensitive to the early stages of plastic deformation than are conventional stress -strain measurements. Dislocation meclzanisms are suggested which are compatible with both the present and the earlier experimental observations. A brief historical introduction of previous work concerned with the study of dislocation motion by ultrasonic-attenuation measurements has been given in Part I. The purpose of the present experimental investigation was to make use of the theoretical considerations from Part I in order to gain further knowledge concerning dislocation motions during plastic deformation. Emphasis was placed on the choice of propagation modes and polarization of the waves, such that interactions between these waves and dislocation movement on a specific slip system could be investigated. EXPERIMENTAL PROCEDURE Since the primary concern of this investigation was dislocation damping, other sources of damping were eliminated as much as possible. The test specimens were 0.5-in.-diam single crystals of 99.99+ pct pure aluminum grown from the melt by a modified Bridgman technique. Ultrasonic-attenuation measurements were made at a frequency of 10 megacycles per sec using a Style 56A001 Ultrasonic Attenuation Comparator manufactured by Sperry Products Inc. after a design by Chick, An- derson, and Truell.1 At this frequency the particle vibrations are essentially adiabatic and thermo-elastic damping should be absent. This frequency was selected since it was one of the frequencies used by Hikata et al.2 n conjunction with tensile tests on aluminum crystals, thus allowing direct comparison with this work. The use of quartz-crystal transducers insures that the amplitude of vibration is not sufficient to cause the break away of the dislocation loops from weak pinning points. The quartz-crystal transducers used all possessed a resonance frequency of 10 megacycles per sec and were thin circular discs 0.375 in. in diameter. X-cut crystals were used to generate the longitudinal waves and AC-cut crystals to generate the transverse waves. Aluminum was chosen as the basic material because it is a typical fcc metal whose deformation behavior is well-known and because the most recent work at the time the present research was initiated was that by Hikata et al. who used aluminum. The present tests were run in compression to see if such tests could be satisfactorily run in compression without being severely masked by grip effects.. A second reason was to compare the results in compression with those of the tension experiments of Hikata et at. Finally, shorter specimens could be run in compression with less over-all damping than in tension. All of the aluminum-crystal test specimens used were oriented for plastic deformation by single slip; i.e., they possessed the orientation having a maximum Schmid factor of 0.5. Because of the well-known time dependence 3 of plastic strain at constant stress, the test specimens were subjected to a quasi-static loading. Previous investigations4-' have indicated that attenuation after plastic deformation is also time-dependent, so any continuous loading of the specimen would show that changes in attenuation were also a function of strain rate. By loading the specimen to a given stress level and holding it constant until the recovery process was essentially complete, the time dependence was eliminated. The quartz transducer was permanently bonded to the aluminum crystal using Eastman 910 cement. Excess cement was removed from around the quartz with DMF (dimethyl formamide). Eastman 910 was found to be far superior for bonding, especially with regard to the shear-wave transducer, since it formed a solid bond which readily supports shear-wave propagation. The solid bond formed by the Eastman 910 cement also insured that the quartz

Jan 1, 1964

By C. Ernest Birchenall

TWO recent papers1,2 cite measurements of surface contour changes on copper which, when attributed to surface self-diffusion, can be interpreted to yield activation energies for surface self-diffusion that approach1 or exceed2 those reported for volume self-diffusion in the same metal.3 It is acknowledged2 that AS must be assigned much too large a value to be physically reasonable in order to make the theoretical Do's agree with the experimental values, if the jump distance is of the order of the interatomic distance. However, long jumps would probably lead to marked anisotropy on planes that consist of ridges and valleys (like (110) in fcc) whereas only mild

Jan 1, 1963

By Robert Lewis

Some recent experiments in the use of compressed air for rock drills at higher than usual pressures, up to 150 lb. per sq. in., emphasize the importance of maintaining the compressed-air system in the best condition if the greatest possible over-all efficiency is to be secured. No claim of high over-all efficiency can be made for the compressed-air system of braking that is used on railroad trains, yet the air brake works effectively. Compressed air is not used efficiently in the rock drill, but no other type of machine drilling is yet a serious competitor of the air-driven rock drill.

Jan 1, 1930

By John Sullivan

Resources for Freedom, a report by the President's Materials Policy Commission, commonly termed either the Paley report, after its chairman, or the PMPC report, was issued in June 1952. The data collecting and assembly work for its preparation were done in 1951. The statistical base in most cases was 1950. It reviewed our economy and predicted what it will be in 1975.* The bases for the predictions were given. Consideration was given not only to statistical data and trends but also to technological changes taking place and likely to take place in the ensuing 25 years that will affect our economy. The supply of raw materials was studied and predictions made as to the availability of supply and the sources in 1975. One of the industries covered was iron and steel. For the most part the report did not attempt to provide a curve showing annual growth for any industry or commodity. It contrasted 1950 with the probable status in 1975. Interpolation between these dates is difficult and the Commission did not intend that it be used for short interim intervals. It is possible in 1958 to show the actual changes from 1950. The magnitude of the changes illustrates the agreement with some interpolation of the Paley report. Statistical comparisons can be general only because the Commission did not postulate a linear change. A study of the iron and steel industry will show if the general predictions have been realized or if gross errors were made. This paper is concerned with such an analysis. It is concerned with the production and consumption of crude, not fabricated products. It attempts to bring various facets of technical and statistical information on the industry up to date.

Jan 8, 1959