Search Documents

By William Kelly, Frederick Laist

The slow, tedious and costly method of reducing copper matte to metallic copper in the reverberatory furnace, commonly known as the Welsh process, was displaced by the rapid and inexpensive converter process about fifty years ago. The art of refining copper was for many generations a carefully guarded secret among the Welsh furnacemen and was handed down among them from father to son. An attempt was made to apply it at Butte when the smelting of copper ore first started there but it proved too difficult and expensive under local conditions, and until the introduction of the converter process the entire output of copper was shipped to Swansea in the form of high-grade (60 per cent) matte. Before the construction of the Manhes converter, attempts had been made to reduce copper matte in the bessemer steel converter, but these failed, chiefly because the air was blown through the bottom of the vessel. The air holes became clogged with chilled copper as soon as the reduction started. Manhes partially overcame this difficulty by placing the tuyeres in the side of the vessel, some, distance above the bottom, thus allowing space beneath them for the copper to accumulate. Nevertheless the first attempts to operate such a converter at Butte were not successful, as no means had been provided for clearing away obstructions, which formed to some extent in front of the tuyeres. This difficulty was overcome by drilling holes in the outside wall of the air chamber directly opposite the holes in the shell and lining, so that these could be punched

Jan 1, 1934

By George C. Fryburg

The oxidation of platinum at high temperatures (above 800°C) is controlled by boundary-layer diffusion, except at the lowest pressures. The rate of oxidation is determined by the rate of diffusion of oxide through the boundary layer away from the platinum. This is in contrast to the situation in tungsten and molybdenum oxidation, where the rate is controlled largely by the diffusion of oxygen through the boundary layer towards the metal. The difference in mechanism is a consequence of the much lower rate of oxidation of platinum. Evidence is presented that supports this mechanism for the oxidation of platinum. SOME years ago we reported1 a study of the oxidation of platinum in ordinary oxygen in the temperature region above 800°C, where the oxide is volatile. All the data available up to that time had been obtained with platinum crucibles or plates heated in tube furnaces. The results were widely variant and highly dependent on the flow rate of gas through the furnace: the faster the gas flow rate, the higher the measured oxidation rate. These results indicated to us2 that reaction equilibrium was being approached in the furnace and that the rate was diffusion limited. To minimize these effects, we employed1 electrically heated ribbons placed in a cooled bulb. We were primarily interested in the low-pressure region, but some experiments were performed at pressures up to 1 atm. We found a peculiar pressure dependency which was explained on the basis that the rate of oxidation was proportional to the pressure at all pressures, but that with increasing pressure an increasing fraction of the volatilizing oxide was back-reflected to the ribbon by the surrounding gas molecules. The oxide molecules are not stable at the temperature of the platinum and are decomposed on impact, the platinum being re-deposited on the specimen. Because of the limitations of space, this explanation was offered summarily without detailed support. Recently, Jaffee and associates3, 4 have suggested that the pressure dependency of our data up to 0.5 torr could be explained on the basis of a Langmuir-type adsorption of molecular oxygen followed by dissociation. Since the correct explanation of the effect of pressure on the oxidation rate is a necessary requirement to the development of the basic mechanism of the oxidation reaction, we felt that the back-reflection theory should be presented in more detail. This is the object of the present paper. RESULTS AND DISCUSSION A typical set of results showing the pressure dependency of the oxidation reaction is presented in Fig. 1, where we have plotted, on logarithmic scales, the rate of oxidation, R, vs the pressure, p. For comparison some results of Krier and Jaffee4 and of Raub and plate5 are also shown. These data were taken at atmospheric pressure using furnaces. The effect of reaction equilibrium within the furnace is apparent from the much smaller values that these observers obtained: Raub and Plate In O2 found a rate of 3.1 µg cm-2 hr-1 compared to our value of

Jan 1, 1965

By B. B. Betty

H. L. Burghoff.*—Have the authors any information on the effect of grain size in these materials? There is a material difference in the grain sizes shown for the Monel and the Inconel. Is a wide range of grain size normally found for each material, and, if so, what is its effect upon creep strength? 11. L. Eiselstein.—The grain size for Monel shown in the micrograph is the usual size found in that product. The grain size of Inconel is about the same as that, too. However, we have run tests on Inconel at higher temperatures than those reported in this paper, and have found that the coarser grain size has a better creep resistance; and that the grain size that gives the best creep resistance at 1600°F. is about 0.005 in. in diameter. We have no test on Monel with varying grain size. J. J. KANTER.†-It has been known for a long time that Monel metal exhibits ductility anomalies at elevated temperatures. Even in short-time test, it can be demonstrated in the range of 900°F. that there is a distinct falling off of the ability of Mone1 metal to elongate, and in rupture tests this shortcoming is still further accentuated. Knowledge of this rupture anomaly of Monel metal may be one of the reasons for which designer's approach certain high-temperature applications with reservations. The authors of this paper have merely demonstrated that for 900°F. the alloy has an ability to elongate 1.7 per cent over a period of some 2700 hr. Before any conviction can be expected from designers that Monel metal is applicable to stress design in such range of temperature, I think it is desirable to demonstrate the capacity for the material to elongate over a longer period of time than has been done in this presentation.

Jan 1, 1945

By R. P. Carreker, R. W. Guard

True stress-true strain data are given for nominally pure molybdenum (99.95 pct) over the temperature range -196° to 1540°C (0.027 to 0.63 T/T). Strain rate sensitivity was determined by rate change tests and stress relaxation tests. Inhomogeneous yielding and strain aging effects were observed. The yield stress and tensile strength depend markedly on temperature below 400°C and are insensitive to temperature in the range 400' to 800°C. The ductile to brittle transition range is +25O to -25OC. Strain rate sensitivity and stress relaxation effects are very large near room temperature. THIS report presents data which were obtained as a part of a continuing program designed to document the deformation behavior of nominally pure metals over a wide temperature range.'" This research program is rooted in the conviction that sufficient tensile and creep data of appropriate quality and detail does not exist to provide precise phe-nomenological descriptions of the deformation behavior of pure metals as a function of temperature, strain rate, and grain size. Such knowledge is needed to provide a firm base for alloy design and an experimental framework to which theories of deformation must conform. These data also complement a parallel exploratory program investigating the properties of refractory metals, including molybdenum, and their alloys. Several important reviews and research reports dealing with the tensile properties of molybdenum as a function of temperature have appeared."-lo To a great extent the work to be reported in the present paper parallels that of Bechtold and of Pugh. The authors' results are in general agreement with those of Bechtold and Pugh. The principle differences be- tween the present experiments and those published previously are as follows: 1—Wire specimens prepared from arc cast molybdenum were used in the present experiments, bar specimens were used by others. Pugh used arc cast material while Bechtold's most extensive results" were obtained on powder metallurgy specimens. 2—Several different grain sizes were tested in the present experiments. 3—The testing range was extended to cover from -196°C to 1570°C (0.027 to 0.63 T/Tm). 4—The combination of wire specimens, high speed autographic recording, and a stiff testing machine permitted more detailed study of initial yielding. The principle contribution of the present paper is the demonstration of the relatively consistent mechanical properties of nominally pure arc cast molybdenum specimens of differing metallurgical history. Bechtold and Scotts have shown that arc cast and powder metallurgy molybdenum samples have comparable tensile properties in the range —75" to 200°C when processed to have the same re-crystallized grain size. Material The molybdenum used in this investigation was supplied by the Climax Molybdenum CO. Its metallurgical history is outlined in Table I; the final products were 0,030 in, diam wire specimens annealed at 1100' and 1375°C and 0.060 in. diam wire

Jan 1, 1957

By Harold Linke

THE following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Hand-book and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman.

Jan 1, 1939

By R. S. McCaffery, R. G. Stephenson

The statistical analysis of blast-furnace data was undertaken to determine some of the relations which exist between the variables involved in furnace operation, and particularly to show the effect of variation of slag composition on such economically important factors as coke consumption, daily tonnage of pig iron and sulfur elimination. It' was desired to correlate the results obtained in commercial practice with those predicted from a study of the quaternary system lime-alumina-silica-magnesia. This paper presents the results of a preliminary study of blast-furnace daily operating reports, and is intended to indicate the suitability of our method of attack and something of the results that may be expected from an extended statistical examination of such data. It has been shown that blast-furnace slags are not composed of oxides, as reported by chemical analysis, but are actually composed of several compounds, each made up of two or more of the oxides present.' These compounds persist in the liquid state, and the properties of a slag are the properties of a mixture of these compounds, and not of a mixture of the ultimate oxides. The oxides lime, alumina, silica and magnesia make up 94 to 96 per cent. of the usual blast-furnace slag, and assuming that we may neglect the remainder of the components, we may determine the minerals present, and their relative proportions, from a study of the quaternary system involving these four oxides. Operating reports from 15 furnaces were available for this investigation. Complete slag analyses for one slag per day were available, per-mittling the calculation of the mineral composition of the slags used. Basic, malleable and foundry irons, with silicon varying from 0.75 to 4.50 per cent. were included in the reports for this examination.

Jan 1, 1931

By H. C. Vacher

THE limiting concentrations of carbon and oxygen which may co-exist at equilibrium in liquid iron are important in determining the degree to which liquid steel may be refined before it is deoxidized. Most refining processes depend upon the oxidation of a highly carburized iron which invariably results in contaminating the steel with oxygen. The oxygen .thus introduced presents many problems to the refiner, who in turn has attempted to rid the steel of this impurity by deoxidation with elements such as manganese, silicon and aluminum. The importance of the limiting concentrations of carbon and oxygen is accentuated in view of a number of recent researches which have indicated in many instances the existence of relations between oxide inclusions and dissolved oxygen and physical properties and chemical behavior of steel. The determination of the equilibrium concentrations of carbon and oxygen existing in iron under steelmaking conditions is obviously of fundamental importance. It has been generally assumed that the product of the equilibrium concentrations of carbon and oxygen in liquid iron is a constant and that this product is directly proportional to the carbon monoxide pressure in equilibrium with the liquid iron. Herty1,2 has computed values for this product based on open-hearth data which are all in the neighborhood of 0.01 to 0.03 (per cent. FeO X per cent. C) for temperatures in the vicinity of 1550° to 1600 C. and one atmosphere pressure. Kinzel and Egan3 have attempted to determine the value of this product by exposing liquid iron to carbon monoxide at one atmosphere pressure. The value reported by them was 0.0005 at 1550°. C. In. order to apply certain equations to the rate of carbon elimination in the open-hearth process, Feild4 found it necessary to assume. a value of 0.0102 at 1580° C. for this

Jan 1, 1931

By J. L. Jorstad

The hypereutectic Al-Si alloys 390 and A390 have wear characteristics superior to any of the more common aluminum casting alloys. This excellent wear resistance, coupled with good mechanical properties, high hardness, and low coefficient of thermal expansion, has made these alloys candidates for the all-aluminum internal combustion engine, the application for which they were primarily developed. A390 alloy is intended for sand and permanent mold casting, and requires a lower iron ccxltent (0.5 pct maximum) than its die casting companion 390 alloy (0.6 to 1.1 pct Fe). The 17 pct nominal silicon in these alloys provides sufficient quantities of the hard primary silicon phase to assure a high degree of wear resistance, yet little enough of this phase, to minimize the casting and m achining problems associated in the past with the hypereutectic alloys. The mechanical and physical properties of 390 and A390 alloys are competitive with the best of the common aluminum casting alloys with the exception of low ductility. This low ductility is not considered a detriment, since in many applications these alloys replace cast iron. Corrosion resistance is similar to the standard alloys 380 and 333. Numerous parts, of varying degrees of complexity, have been cast of alloys 390 and A390, including engine blocks and heads. The deviations from normal good handling and casting practices that are required for the alloys are those associated with the presence of the primary silicon. To obtain optimum strength and machinability, the molten alloys should be treated with phosphorus to refine the primary silicon phase. Care must be exercised to properly control the pouring temperature and rate in order to minimize primary silicon growth and segregation. AUTOMOTIVE engineers have for years recognized the advantages of lighter weight and better heat transfer that aluminum could offer as material of construction for engine blocks. These advantages alone, however, are insufficient justification for acceptance of aluminum engines by the automotive industry. To be acceptable, an aluminum engine first must pass all tests to which cast-iron engines are subjected, and, in addition, must represent no cost penalty in manufacturing. None of the conventional aluminum casting alloys have sufficient wear resistance to withstand the tests to which cast iron is subjected as a cylinder bore material, and recent attempts to manufacture aluminum engines with cast-in-place iron sleeves could not compete costwise with the equivalent cast-iron engine. The prerequisite to an acceptable aluminum engine seemed to be a casting alloy with a high degree of wear resistance that would eliminate the necessity of cast-in iron sleeves or liners. The hypereutectic A1-Si alloys 390 and A390 have met this challenge.' Combined with modified pistons and a patented cylinder bore surface finish,2 the performance of these alloys in more than 1300 cold start and cold scuff tests, over 3500 hr of dynamometer wear and endurance tests, and more than 350,000 miles of road tests leaves no doubt as to the feasibility of running on bare aluminum cylinder bores. ALLOY DEVELOPMENT The desirable characteristics of the hypereutectic A1-Si alloys have been recognized for some time. Their excellent wear resistance and low coefficient of thermal expansions have been used to advantage in the production of diesel-type pistons in Europe and to a limited extent in this country. The major contributor to the good wear resistance of these alloys is the extremely hard primary silicon phase in the microstructure. Although the percent silicon used experimentally has been much higher, most commercial alloys have ranged from about 14 to 25 pct. Generally, as the silicon content is increased, wear resistance increases, and the coefficient of thermal expansion decreases. With increases in silicon, however, machinability and cast-ability tend to suffer. The development of a satisfactory aluminum engine block material at Reynolds involved the testing and evaluation of many alloys, covering a wide range of silicon contents and numerous variations of iron, copper, magnesium, manganese, and other alloying additions. Castability, mechanical and physical prop-

Jan 1, 1969

By Charles E. Glass

The stabil ity of engineered embankments subjected to earthquakes has received considerable attention in the last 10 years, but most of the effort has been directed toward stability of earth dams. Based upon past performance, earthquake- induced failures on non-impounding mine waste structures will likely correspond to small, local slumps or debris slides, and their stability should be considered as an integral part of mine economic planning. As such, stability considerations should include earthquake hazard, characteristics of earthquake ground motion, dynamic slope stability, and the impact that waste-dump failures have on mine operations. Numerous techniques have been proposed for analyzing the stability of embankments subjected to earthquakes. Before choosing an analysis technique, it is worth noting two important differences between the dynamic response of waste embankments and natural slopes. First, waste embankments respond as structures having unique modes of vibration, which causes embankment motions to differ from nearby ground motion. Second, because of embankment response, accelerations can be different at embankment crests than elsewhere in the structure and occur at frequencies that do not correspond to input ground motion. Because of these factors, embankment response should be calculated prior to slope stability assessment. In this paper several analysis techniques designed to calculate slope stability are evaluated, and conventional pseudostatic techniques are shown to be inappropriate for dynamic considerations. Techniques to calculate dynamic stability should include embankment response, all characteristics of earthquake motion, and roughness along failure planes as input, and should provide a displacement time-history of the slide mass as output. Two techniques satisfy this criterion, and in this paper the LADRS technique is recommended for its versatility and simplicity.

Jan 1, 1985

By E. M. Wise

PLATINUM and palladium are the most generally useful, most ductile and least rare members of the platinum family. They have many impor-tant applications in the pure state but for other applications it is fre-quently desirable to harden them and otherwise modify their properties by alloying small amounts of the other platinum group metals with them. These alloys are frequently required to withstand very drastic forming operations and to possess certain mechanical properties to fulfill specific requirements. For these reasons a knowledge of the tensile properties and annealing characteristics of pure platinum and palladium as well as their more useful commercial alloys is important to the user, and the fabricator. The present work was undertaken to fill this need. Rather brief (5 min.) annealing treatments were employed to render the data of maximum practical value and all tests were conducted upon 0.050-in. dia. wire, initially reduced 50 per cent in area by cold drawing, for the same reason. CONCLUSIONS 1. Pure (thermocouple grade) platinum reduced 50 per cent by cold drawing exhibits the following tensile properties: ultimate tensile strength, 36,000 lb. per sq. in.; proportional limit, 27,000 lb. per sq. in.; elongation, 2.5 per cent in 2 in.; reduction in area, 95 per cent. When fully annealed by treatment at 1100°C. its properties are: ultimate tensile strength, 20,700 lb. per sq. in.; elongation, 30 per cent in 2 in.; reduction in area, 93 per cent.

Jan 1, 1934

By Clyde E. Williams

The purpose of this report is to supply the Coal Classification Committee' with information for use in the formulation of a system of classification of coals according to their uses. Consideration is given here only to the nonferrous metallurgical operations that consume relatively large amounts of coal or coke; i. e., the smelting of copper, lead, zinc and aluminum. For all of these uses, coal of certain definite qualities is desired. Geographical location, however, often determines whether these qualities can be specified. In some instances the preferred qualities must be specified, regardless of cost. In others, quality may be sacrificed for lower cost, although the best quality consistent with cost is usually the determining factor. These considerations will be outlined in the following discussion under the various uses, which, however, will illustrate the impracticability of preparing definite specifications for coal used in the majority of the nonferrous industries. Coal and Coke in Copper Metallurgy From the standpoint of coal consumption, copper smelting and refining operations are the most important of the nonferrous metallurgical uses of coal. As nickel ores treated in the United States and Canada are associated with copper, the first step in their recovery is really a copper-smelting operation; accordingly, the following considerations under copper smelting apply equally to nickel. Copper Smelting in Reverberatory Furnaces.—For a long time, rever-beratory copper-smelting furnaces were fired with lump coal burned on grates in a fire box. Later, lump coal was displaced by pulverized coal or oil burned directly in the smelting chamber. Recently, natural gas has been used in several plants, although producer gas was used for this purpose at Great Falls as early as 1903.2 Requirements for coal used in

Jan 1, 1932

By A. S. Richardson

THE design of mine airways receives, in general, very little engineering treatment. To a large extent this is, of course, due to the fact that information upon which to base calculations is seldom available in definite form. In many mines the extent of the workable deposits may not be known at the time an air course is planned, and the length of service is indeterminable. Volume of air required for ventilation may also increase with extension of the life of a property, and natural obstacles, such as heavy ground, often place limitations upon the size of opening that can be maintained. Perhaps a majority of the shafts used in ventilation of metal mines were originally intended as hoisting shafts, and many of the tunnels and cross-cuts similarly used, were also designed as haulage ways or for other operating purposes. Even when a shaft is sunk solely for ventilation, custom usually dictates a size and shape consistent with the type commonly used for ordinary operations, because experience has demonstrated it can be excavated and maintained. In fact it may not be very far wrong to say most ventilation openings were never made with any consideration as to economic design for such use. When an air course is required to pass air between different parts of mine workings under a fixed pressure, the size of opening required for a given volume of flow, is, of course, determined by the resistance factor of the air course. It is then impossible to proportion the opening with reference to economics of power consumption, and this paper is limited to the design of openings where ventilation pressure or power consumption may be varied for economic advantage.

Jan 2, 1926

By F. W. Jessen, N. Mungan

The plastic flow characteristics of clay water suspensions were first recognized by Binghaml in 1916 and further studied by Ambrose and Loomis' in 1931-1932. Many physical and chemical properties of clay suspensions are deeply influenced by particle size distribution as well as by the exchange cation. Separation of a number of fractions is particularly helpful in making a detailed study of a suspension. A limited amount of work has been conducted on the effects of particle size on specific properties of mud drilling fluids. A knowledge of particle size distribution is essential for a better understanding of fundamental properties of clay suspensions, particularly viscosity and gel strength. The purpose of this investigation was to study the effect of particle size on the viscosity and gel properties of clay suspensions and to determine any changes in mineral composition accompanying variation in size. EXPERIMENTAL PROCEDURE Numerous methods may be used to fractionate a poly-dispersed clay suspension into nearly mono-dispersed systems. Particles larger than 44 micron (325-mesh) may be obtained by wet screening. For sizes from 44 to 1 micron, the fractionation may be accomplished by sedimentation, elutriation plus microscopy,' or turbidimetry.6 When dealing with systems which contain a major portion of particles below l-mi-cron size, slit ultramicroscopy,7 centrifuge methods of Svedberg,5 eams,9 and McBain,l0 and X-ray methods" may be employed. The Sharples super centrifuge has been proved suitable for the economical separation of suspended particles of submicron range.12,13,14 Three-hundred and forty-five gal of 1 per cent by weight Aquagel suspension was mixed in a high-speed 5-gallon mud mixer and the suspension was allowed to stand in 5-gal glass bottles for 30 days to assure full hydration. All particles larger than 44 microns were removed by wet screening. Five fractions in the range of 44 to 1 micron were obtained by sedimentation. The Sharples super centrifuge method described by Hauser and Reed.13 Norton and Speil,14 Ha user and Lynn,15 and Hauser and Schachman,10 as employed to yield five fractions of submicron size. A super centrifuge operation chart prepared by Fancher, Oliphant, and Houssierre12 was used to determine operating conditions for the desired particle ranges. The clay suspension, after removal of all material above 1-micron size, was centrifuged. During rotation of the bowl, the particles were deposited on a thin plastic liner which fit closely inside the bowl. After passing 5 gal of suspension through the centrifuge, the liner was removed and the particles on the liner were scraped off, remixed and recentrifuged. This was repeated five times. Thus, Fractions H, I, K, and L were obtained. The finest fraction, M, remained in an approximately 0.4 per cent suspension. Water was evaporated under reduced pressure from this suspension to yield the finest particles. Results of the fractionation are included in Table 1. In order to achieve proper orientation and humidity conditions for X-ray diffraction analysis, the following procedure was employed. The dilute suspensions were placed on glass slides and allowed to dry at room temperature. This was repeated several times. Previous to measurement each sample first was placed in a water desiccator for half an hour and then allowed to stand for 15 minutes at room temperature. thus yielding an equilibrium condition of about 52 per cent relative humidity. The relative humidity of the room in which the X-ray diffraction was carried out was maintained at approximately 50 per cent so that there was no change in the spacings during the X-ray examination. Samples

By R. D. Mollison, C. F. Fogarty

Sulfur is widely distributed in nature. It is present in the earth's crust, the ocean, the meteorites that come to us from cosmic space and in practically all animal and plant life. According to Clarke,9 the earth's crust contains 0.06 pct sulfur. Large quantities of free or combined sulfur are found in coal, natural gas and petroleum. Mineral waters contain sulfates and hydrogen sulfide. Sulfur is rather plentiful in the crust of the earth; however, only under special circumstances can it be produced profitably. Sulfur is one of the cheapest raw materials used by industry; and, therefore, the economic feasibility of a given deposit is strongly dictated by the law of supply and demand on local as well as world-wide levels. The forms which are commercially important are elemental sulfur or brimstone, and the sulfides such as pyrite (FeS2), pyrrhotite (FenSn+1), chalcocite (Cu2S), sphalerite (ZnS), and galena (PbS); the sulfates such as gypsum (CaSO4,2H2O), anhydrite (CaSO4), and kieserite (MgSO4,H2O). Elemental Sulfur Elemental sulfur is found in many localities, generally in solfataras and gypsum type deposits. The solfatara deposits are found commonly in the neighborhood of active or extinct volcanoes as in Italy, Japan and Chile, or fumaroles associated with mineral springs such as the Mammoth Hot Springs in Yellowstone Park. Here the sulfur is deposited in tufas or other porous host rocks. This type of sulfur deposit probably results from the oxidation of hydrogen sulfide or the reaction of hydrogen sulfide with sulfur dioxide. Most of the world's supply of elemental sulfur comes from the gypsum-type deposits. Here the mineral occurs as either crystalline or amorphous sulfur in sedimentary rocks in close association with gypsum and limestone. This association is characteristic and occurs in almost all the great gypsum beds of the world, although sulfur is not always present in quantities of economic importance. Various theories have been advanced to account for this association. Bischof5 suggested that the sulfur came from hydrogen sulfide which resulted from the reduction of calcium sulfate by carbon or methane in accordance with the following reactions: CaSO4 + 2C= CaS + 2CO2 CaS + C02+ H2O = CaCO3 + H2S CaSO4 + CH4= CaS + C02+ 2H20 2H2S + 02= 2H20 + 2S All of the sulfur-bearing domes on the Gulf Coast have calcium sulfate in great quantity in the cap. They all show the presence of hydrocarbons. The oxygen for the final reaction could have been supplied by circulating ground waters. The principal objection to this theory is that temperatures of 700° to 1000°C are needed to reduce the sulfate to sulfide with carbon compounds. The geologic evidence is that the temperature of the sulfur-bearing domes of Texas did not exceed 100°C. Proponents of the theory say that geologic time or a catalyst replaced temperature. According to another theory the sulfur in the salt domes is the result of bacterial action. Sulfate reducing bacteria have been detected in sulfur cores and in the formation water issuing from salt domes. It has, therefore, been suggested that these bacteria converted the sulfate to sulfide which subsequently was converted to elemental sulfur.

Jan 1, 1960

Technology has no recognized rank in what is called polite literature; the subject-matter of engineering is not supposed to lend itself to artistic treatment; we are the hewers of wood and drawers of water to the high-priests of learning that live on the cold summit above our humbler dwellings. Therefore the hierophants smile at the notion of 'style'- “that curiously personal thing”--in technical writing. The "great art" of Pater, the "inevitable phrase" of Raleigh, the "note of distinction" that Arnold demanded are said to be beyond the scope, as they are supposed to be beside the need, of a writer on geology or engineering. This is a narrow view. Science, no less than belles lettres, calls for the best exercise of the human intelligence; the art of writing should be employed as skilfully and as earnestly in a description of the structure of the Sierra Nevada, or of the construction of a tunnel through the range, as in a rhapsody welcoming the rosy fingers of the dawn. The idea still lingers that fine writing does not befit technology, even though the masters of the Victorian period- Huxley, Tyndall, Ruskin-proved that science is worthy to be arrayed in the best robes that the looms of thought can weave. At the beginning of these lectures I quoted Barrie's remark touching the inability of the scientific man to express himself. That imputation has been passed to the technologist, whose utilitarian pursuits are supposed to make him too clumsy for the refinements of human speech. We may not have acquired the self-consciousness of those writers on Art whose "power of expression is so cultivated that their sensual caterwauling may be almost mistaken for the music of the spheres"; nor can we imitate the politicians, who have the ability to speak far beyond anything that they may have to say; but we too have a litera-

Jan 1, 1931

It is probable that the first commercial production of coal in Ohio was for the supply of Wheeling, before mines were opened at that place. This coal came from Pipe Creek in Belmont County,l where the seam was exposed a short distance above the river. This movement could not have lasted more than a few years, because coal was being mined at Wheeling in 1818, and probably before that.2 Mining began in Tuscarawas County in 1810 and in Perry County in 1816, and has been followed steadily since then. In the eighteen twenties the Pomeroy field in Meigs County, Jackson County, and the northern Ohio field in Summit County commenced production. All of the early data available are given in Table 57. No early official reports were made, but after 1859 the Secretary of State published statistics of production, admittedly inaccurate, by counties, and under various officials these have been continued to the present day. Ohio has never published statistics about coal in smaller units than the county; no reports of individual properties have ever been collected. The period from 1800 to 1885 includes the opening of practically all of the coal fields of the state, although those of eastern Ohio were not large producers at its end. During this time the use of raw block coal in blast furnaces had begun and ended, and at the end, coke was nearly the universal fuel for this purpose. Much of the coal traffic on the Ohio River and its main tributaries originated in the necessity of a fuel supply for Cincinnati and other down-river cities. This traffic started in 1794, and few records of it are available until many years later; in 1846 records of the movement to Cincinnati began and have been maintained with increasing thoroughness, and represent one of the most complete records of such a traffic extant anywhere. As these data show the originating fields of most of the coals used there, the available figures to 1885 have been collected in Table 16.

Jan 1, 1942

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938

By J. M. Callow

HISTORICAL SKETCH THE selective action of oils for lustrous minerals was first disclosed by Haynes in 1860. In 1885, Miss Carrie Everson elaborated this idea and also disclosed the fact that acid increased the. so-called selective action. Her patent called for oils, either animal, vegetable or mineral, also for an acid or salt. The process was tried out on a practical scale in Baker City and Leadville, in 1889, and failed: first, because,, as has since been shown, of the unsuitability of the ore to flotation; and second, because the invention was too far in advance of the times. Then followed the Elmore brothers, first with their bulk oil processes and later with their vacuum method. The basic principles of oil flotation were undoubtedly covered by the above inventors, the work done since their time being merely a building up on ground work laid by them. Different kinds of oil, different quantities of oil, and all the varying degrees of agitation, were all exemplified and practiced by them in one phase or another, and the developments that have since been made are but elaborations of the fundamental principles laid down by Haynes, Everson, and the Elmore brothers. In 1902, the Potter-Delprat process was developed in Australia. In this process no oil was used, the mineral being raised by the generation of gas, brought about by the introduction of acid into the pulp. The mineral particles appeared on the surface of the separatory vessel, in the form of a scum or froth, buoyed up-by minute gas bubbles attached to them. This no doubt first gave the suggestion of gaseous flotation. In 1902, also, Fromont, an Italian, was granted a patent in which. he combined violent agitation with oil and gaseous flotation, the gas being generated within the pulp, in much the same way as in the Potter-Delprat process.

Jan 12, 1915

By Francisco Cadena

THE construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data bearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. TABLE 1 .-Typica.1 Chemica1 Analysis [PER CENT H20,1100F ............................................ 0.0'2 Ignitionloss ............................................. 43.56 MgO .................................................. 19.19 CaO .................................................... 29.07 FezO .................................................... 0.39 A1203 .................................................... 1.94 FezO .................................................... 0.39 A1203 .................................................... 1.94 ..................................................... 5.75 SO2.. .................................................. Tr.] Rock was carried by 12-yd. dump trucks to a 42-in. gyratory crusher set at 6 1/2 in. The product of the primary crusher was taken by a belt conveyor to a double-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1937