Search Documents

By E. S. Burnett, R. V. Higgins, H. C. Miller

Information obtained from subsurface pressure and ,temperature measurements in oil wells now is recognized as invaluable to geologists, engineers, and operators of oil properties. Available only during the past few years, data resulting from subsurface-pressure surveys in oil wells already have found widespread application in the estimation of reserves and in the planning of comprehensive oil-field development programs. Subsurface pressure and temperature data, together with measurements of fluid volumes produced by individual wells and specific gravities of the fluids, also are included in the fundamental information essential in studying the movement of oil, gas and water through reservoir sands to wells. Heretofore, laboratory findings were relied upon almost entirely for information pertaining to the mechanics of flow of fluids through porous media, because there was no way to check laboratory results with actual performance in underground formations until subsurface pressure and temperature instruments were developed. Laboratory and field experiments now lend themselves to closer correlation—a fact that will accelerate the interpretation of many phenomena that occur when oil and gas flow through reservoir rocks, thousands of feet below the surface of the earth. This paper summarizes the results obtained thus far in a Bureau of Mines study of certain data pertaining to subsurface pressures and production of wells producing oil and gas (and water). For wells that have been studied, flowing naturally under volumetric or hydraulic control, a simple relation has been found between the mass rate of fluid (oil, gas and water) production and the corresponding drop in pressure in the reservoir sand. The equated relation embodies a productivity factor or "index" expressed in terms of mass rate of fluid production per pound drop in pressure through the sands. The equation as developed is an expression of the ability of a well to produce, which permits comparison on a uniform basis of the productivities of different wells. The study shows also that over the range of observed data a productivity factor

Jan 1, 1937

By N. B. Pilling

THE development of a proper treatment for shells in connection with war contracts has brought to our attention the fact that the temperature of the liquid bath in which steel is quenched has a decided influence on the speed of cooling in the case of some liquids and very little in the case of others. Widely different physical results have been obtained by the use of water spray, water immersion, and oil immersion and further experiment has shown that the quenching effect of water used as a spray or an immersion varies greatly with the temperature of the water. The present experiments were undertaken with the idea of obtaining information of a quantitative nature regarding the quenching properties of a number of liquids used commercially in hardening steel. The general features of such cooling media are common knowledge and in the literature may be found records of numerous attempts to evaluate the cooling power of a liquid when used as a quenching bath. Much, if not most, of the data given on this subject is in the form of a simple statement of the time required for a certain heated mass to cool between two arbitrary temperatures when immersed in the liquid, quite regardless of the path of the temperature change. Our own purpose has been somewhat different. We have attempted to isolate that property of these. liquids having to do with their ability to absorb heat rapidly, as distinct from the behavior of a considerable mass when exposed to different thermal environments. More specifically, from the data obtained through autographically recorded cooling curves of a small standard mass quenched under various conditions, we have tried to analyze the mechanism of heat absorption by the several liquids, measure the changes in its rate as a function of the temperature of the surface of transference, and ascertain the influence of the temperature of -the liquid itself upon both.

Jan 9, 1919

By R. G. Hall

An article on the subject of electrolytic zinc no longer needs to be preceded by an apology. The production of zinc by electrolysis is past the laboratory stage and has become an economic factor of considerable importance in the total production of zinc in the United States. The various methods of procedure to be followed fa the greatest economy of manufacture are fairly well known, consequently a detailed description of any method is no longer necessary or desirable. In this paper I shall endeavor to lay down some of the governing conditions in this industry, the relation of methods to ore deposits, freight rates, and sources of power supply. Power Points Assuming for a moment that, for the present at least, the electrolytic production of zinc will be confined to Those localities having developed water power, a glance at these powers so developed in the United States, with their relation to known zinc orebodies of economic size, will not be without interest. Northwest In the Northwest we have water powers, developed and undeveloped, . in Washington and Montana. These must, of course, bear a close relation to the rapidly growing zinc production of the Coeur d'Alenes and of the Butte districts. In general, the power of the territory in question is relatively low-priced, at least as compared with the cost of developing power from coal, and the near neighborhood of large bodies of more or less complex zinc ores makes these water powers of more than usual interest. The same remarks may be applied equally to the developed water powers of the Canadian side of the line in the Northwest, where we have again commercially available complex ore deposits such as are being exploited today at and near Trail. California One of the large complex ore deposits of the far West is to be found in Shasta County in the immediate neighborhood of the territory of the

Jan 1, 1918

By Charles Colcock Jones

In any discussion of this very large subject we are confronted at the outset with so many obstacles that at best only a fragmentary and rather disconnected presentation can be made of it, and my hope is that building from the few facts I have to offer a more complete knowledge may be secured. In the whole intermountain and Pacific Coast region, west of Pueblo, Col., and from Canada to Mexico, there is no production of pig iron, and steel production is confined to the manufacture of a small amount of open-hearth steel from scrap. When we consider the area, the resources, and the several centers of population, this condition seems anomalous, even in the face of every counter argument as to cheap water transportation, or other means of transport from the Atlantic Seaboard or from the iron and steel centers of the Middle West. This comatose condition, if such a term may be applied, is certainly not due to a lack of all the essential materials and factors for success in iron and steel smelting, but is rather, I think, due largely to the general fact that it is only within a comparatively few years that the centers of population on the Pacific Coast have attained a size that would entitle them to the position of distributing or freight centers, or that the "back country" has been enough built up to make it sufficiently interesting to the railroads to foster trade from the local centers to the interior points rather than seek to supply such local centers and the interior by a transcontinental haul. "Ore Supply Edwin C. Eckel, in his monumental work on Iron Ores, has but little to say concerning the Pacific Coast deposits. He mentions (p. 269) those of Minaret, Madera County, and the Eagle Mountains, Riverside County, Cal., "perhaps 50 to 100 million tons each;" the deposits in Shasta County, worked for the electric furnace on Pitt River; and

Jan 1, 1916

By J. E. Lawver, W. D. Carrier

During the past 20 years, millions of dollars in research effort have been spent to improve methods of phosphate clay dewatering and disposal. Although to date no proven large-scale system has been developed that will result in ultimate below ground storage without the use of at least temporary dams, considerable progress has been made and a variety of techniques are being tested, some on a large scale. This paper summarizes the use of mathematical and centrifuge (physical) models that can analyze and evaluate various systems for the consolidation of phosphatic clays. These provide a powerful tool for engineers responsible for land management and mining waste disposal.

Jan 1, 1985

By C. C. Harris

The modern flotation machine is the result of decades of adaptation to a changing environment. In response to falling ore grades, and rising demands, tonnages, and costs, attempts are now underway to expand machine capacity by about an order of magnitude, while at the same time maintaining metallurgical performance and if possible reducing power requirements per unit throughput. Empiricism and rule-of-thumb have guided flotation machine design and scale-up, and a current need is for the development of a fundamental understanding of the subject. Design features of current and some obsolete machines are discussed in an attempt to outline those principles of flotation machine design which are known, and to delineate topics needing investigation. Attempts are made to distinguish between essential machine features required by the physics of the process, those features resulting from speculative theories on the flotation mechanisms, and features which are essentially styling variations. Topics discussed include: flotation mechanisms; tank and impeller/ stator design and dimensions; impeller speed; aeration; power consumption; particle suspension and dispersion; capacity; correlation of design parameters and operating variables; scale-up and scale-down; materials flow; problems in machine design. Design details and operating data for several current machine families are provided in Appendices.

Jan 1, 1976

By R. J. Wygal, J. Naar

An equation for three-phase (water, oil, gas) imbibition oil permeability is developed, assuming the water to be the dominant wetting fluid. Oil isoperms are obtained for consolidated sandstones characterized by 1/pc2 = CS*. The evolution of an oil-gas system imbibing water from Swi to(Sw,imb )max is shown to proceed along a line of constant oil saturation with increasing oil permeability and decreasing gas saturation. When the gas satuation cannot be reduced further, the system evolves along a line of constant Sg with decreasing oil saturation and permeability. The initial gas saturation is shown to reduce markedly the effect of complete wetting by either oil or water on flow performance. INTRODUCTION Imbibition oil isoperms are required for performance prediction when a well is producing water, oil and gas. This situation occurs in multiphase displacements such as underground combustion, steam injection and the water flooding of highly depleted reservoirs. In a recent paper,1 a model was presented for the prediction of two-phase imbibition characteristics. This paper extends the imbibition model to the case of three phases by assuming that the water is the dominant wetting fluid. The following results were obtained from the model: (1) an analytical expression of oil isoperms; (2) oil isoperrns as functions of reduced water, oil and gas saturations, valid for all sandstones having a capillary pressure curve which can be approximated by 1/PC = CS*; and (3) evaluation of the three-phase flow performance as dictated by complete wetting by either oil or water. The agreement between predicted and observed oil recovery in the presence of a gas phase, reported in Ref. 1, is a partial support for the present development. However, experimental data are not available at this time to check fully the model predictions. Perhaps this paper will stimulate the collection of such data. The imbibition model of a porous medium has been described previously, and the reader is referred to the paper of Naar and Henderson1 for details. In brief, the model is formed by the random interconnection of straight capillaries, with a provision for the blocking of the non-wetting phase by the invading wetting fluid. The following expressions were derived from the model. 1. The amount of oil blocked by the invading water is

By Christopher Haycocks, J. Richard Lucas

The growth of computer and ground control technology in recent years, combined with an urgent demand for low-cost fossil fuels and mineral resources, has set the stage for full-scale utilization of computers in mine planning. Steeply rising production costs and the need to preserve the environment are placing great demands on engineers to improve their mining efficiencies, which can best be accomplished by applying the full capabilities of the computer. Pressure to develop and perfect programs with an immediate potential for improving mine design, reducing mining costs and extending the viable coal reserves of the country has already come to bear in the form of exploding energy requirements, environmental considerations and the visible limitations of other energy sources.

Jan 4, 1973

By H. A. Doerner

METALLURGICAL problems relating to manganese and chromium ores have striking similarities. Ferroalloys, essential to the steel industry, are produced from both ores. Most of these alloys are obtained from imported ores, as domestic deposits have not yielded enough ore of metallurgical grade to meet more than a small fraction of vital needs. A survey of domestic manganese and chrome de- posits reveals numerous small, dispersed bodies of fairly good ore, none of which appears to be capable of yielding significant amounts of marketable products. To stimulate development of such deposits and to increase Government stockpiles, General Services Administration is offering $115 per long ton for limited amounts of chrome ores and $110 per long ton for 48 pct manganese ores that meet metallurgical specifications, with bonuses or penalties for grades above and below specifications.

Jan 4, 1953

By N. Jaffee, J. E. Dorn

An activation energy of 27,400 5 1000 cal per mole was obtained for the creep of poly crystaLline aluminum over the temperature range of 273° to 350°K, at strains varying from 0.003 to 0.230. Stresses varied fronz 2250 to 6000 psi, strain rates from 0.1145 x 10-5 to 29.5 x 10~s min.-1. A strain temperature-compensated time correlatzon was oblained indicating that the structure was depedent solely upon the strain at a given stress; X-ray diffraction analyses and tensile tests on precrept specimens verified this. PREVIOUS investigations1 have revealed that the apparent activation energies for creep of high-purity polycrystalline aluminum are insensitive to the applied stress, strain, and strain rate. On the other hand, the apparent activation energy is dependent on the temperature1,2 as shown by the data reproduced in Fig. 1. Each plateau of this curve is associated with a unique rate-controlling dislocation mechanism for thermally activated creep. It is now very well-established that over the high-temperature range, where the activation energy is about 35,500 cal per mole, the creep rate is controlled by the dislocation climb mechanism. 3 Over the intermediate range of temperatures, from about 260° to 370°K, another unique activation energy, namely 28,000 cal per mole, is obtained. Current evidence strongly supports the contention that cross slip is the rate controlling mechanism for creep in this case: 1) Crystal recovery can occur by a number of mechanisms prominent among which are climb and cross slip. Astrom,4 using the Borelius micro-calorimeter, reported rapid crystal recovery of cold-worked polycrystalline A1 at 340° to 370°K giving an activation energy of 28,000 cal per mole and additional recovery at 455° to 478°K giving an activation energy of 3 6,000 cal per mole. Whereas the latter recovery process was clearly associated with the dislocation climb mechanism, the former, 28,000 cal per mole process could have arisen as a result of the cross-slip mechanism. 2) Single crystals of high-purity A1 favorably oriented for octahedral glide exhibit an activation energy for creep of about 3400 cal per mole over the range from 0° to 400°K and that of about 28,O:O cal per mole over the range from 600° to 775°K . Whereas the lower activation energy process is accompanied by the development of sharp slip-band traces, the 28,000 cal per mole process was uniquely characterized by extensive cross slip. 3) Theoretical calculations by Seeger and schoeck6 suggest an apparent activation energy for cross slip in A1 of about 24,000 cal per mole and another theoretical estimate by Friedel 7 gives the observed 28,000 cal per mole as the theoretical activation energy. It is therefore consistent with this evidence to, at least tentatively, ascribe the 28,000 cal per mole creep process in A1 to the operation of cross slip as the rate controlling mechanism. Although creep has been rather well-explored in the dislocation climb range, very little, excepting perhaps the activation energy, is known about creep in the cross slip range. This investigation was undertaken, therefore, to reconfirm the activation energy for creep in polycrystalline A1 in the intermediate temperature range and to study the strain-time relationship for creep at a constant stress in the cross slip region. EXPERIMENTAL PROCEDURE AND TECHNIQUE The three types of high-purity A1 alloy specimens described in Table I were used in this investigation. Specimens were milled from 0.100 in. thick cold-rolled sheets with their tensile axes in the rolling direction following which they were given a recrys-tallization and grain growth heat treatment at temperatures well above those which were subsequently employed in the creep tests.

Jan 1, 1962

By M. Streat, R. Y. Qassim

Summary This paper reviews the developments in uranium process technology as a result of modern trends in the design of ion exchange equipment. The operation of the Cloete-Streat fluidised bed contactor is described and pilot-plant development of this contactor for uranium slurry work at Imperial College is outlined. The properties of a suitable ion exchange resin for slurry treatment are discussed, together with a description of relevant rheological properties of ore suspensions. A prediction of ion exchange resin- slurry behaviour is presented in order to establish the feasible operating limits for this type of R-I-P contactor.

Jan 1, 1973

1. Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc., may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, together with the names of its President and its Secretary, may be published in the Bulletin or the Year Book of the Institute. The individual members of such a society will not be catalogued as individual members or associates of the Institute, but may at any time be proposed for election as members or associates of the Institute, in the usual way. 2. Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied with suitable testimony as to character and qualifications, will have special, weight with the Membership Committee of the Institute, in its consideration of the proposal of a candidate for membership or for Junior membership.

Jan 1, 1923

By L. Zwell, H. A. Wriedt

In describing their procedure for measuring the lattice parameters of solid solutions, Abrahamson and Lopata report (p. 77) the final heat treatment of their alloy specimens as "700°C for 100 hr, followed by a furnace cool". The isothermal part of this treatment may be expected to precipitate solute in excess of the stable a solid-solution limit at 700°C; the subsequent slow cooling is likely to reduce the dissolved solute still further. Fig. 1 (upper) presents the data for titanium alloys so he;rt-treated and shows the lattice parameters of solid solutions containing up to 3.5 at. pct Ti; Fig. 17 (lower) shows 2 at. pct Ti as the solubility limit in a iron at 700°C. Figs. 1 and 17 are thus incompatible. The paper contains comparable incon~patibilities for zirconium alloys, for niobium alloys, and for tantalum alloys. The final heat treatment at 700°C may also be responsible for the anomalous "knee" in the lattice-parameter data for nickel alloys, Fig. 3. The "knee" composition is located near the 700°C limit of the stable a solid-solution field;37 alloys of the experimental composition range with more nickel than the "knee" composition are two-phase at 700 C and prolonged heat treatment of them at 700°C would tend to produce inhomogeneity rather than homogeneity. In Figs. 4 and 7, the composition ranges of the zirconium, hafnium, and niobium alloys examined terminate at alloy concentrations of 0.1 to 0.2 at. pct. These metals form very stable oxides and their partial removal from solid solution in iron by impurity oxygen may be expected. We believe that the authors should have reported the procedure by which they distinguished the amounts of alloying elements in solution and in oxide. The diagrams pertaining to copper in Figs. 3 and 18 (lower) are almost certainly incorrect. Three recent investigations of this system38-40 all substantially agree on the solubility of copper in a iron, finding it to be much larger than that reported by Abrahamson and Lopata. The change of the lattice parameter with composition reported by Abrahamson and Lopata is too large by a factor of three to five, as seen by comparison with the findings of other investigators.41738 Moreover, the authors violate, in Fig. 18, the accepted Fe-Cu constitution diagram37 by ignoring the eutectoid at about 850°C.

Jan 1, 1967

By P. S. Rudman

Laves phases, AB2, are considered as Izerrzisub-stitutional solutions m1hich are defined by a one-for-truo replacement scheme. Atomic-size tnisfit is considered in terms of deviations of the ratio 2V°b/V°A from unity, where v° = atomic volume. A simple elastic model has been used to calculated deviations from "Vegard&apos;s law of atomic vol-umes". Comparison has been made between calculated and observed atomic-volume deviations fov 222 Laves phases. Agreement is generally very good although there ave some few exceptions which appear to be excusable in terms of electronic changes that ore beyond the scope of the present model. We can consider the formation of a binary sub-stitutional solution A-B from an A solvent as one-for-one replacements of A atoms by B atoms. As the atomic-size ratio deviates from unity, the solution becomes thermodynamically less stable and hence more restricted because of atomic-misfit strain energy. In accordance with our previously presented conclusion1 that the atomic volume, v, is in general the most appropriate measure of atomic size, the ideal size ratio for a binary sub-stitutional solution is vg/vA = 1. The Laves phases have been described by Berry and Raynor2 in terms of various stacking sequences of hexagonal layers of B atoms for the three structures MgZn2(C14), MgCu2(C15), and MgNi2(C36). To form the Laves phase of ideal composition AB, we start with complete hexagonal layers of B atoms in the appropriate stacking sequence and we remove, according to an appropriate scheme for each structure, two out of every four B atoms and replace the two removed atoms by one A atom. We thus might expect to find that the ideal size ratio for the Laves phases is 2v/B/ VA= 1. From this point of view, then, we call Laves phases hemi-substitutional solutions since we employ one-for-two replacements. By analogy with substitutional solutions we can expect for Laves phases that as the ratio 2VB/Va deviates from unity the phase occurrence will be more restricted. Laves3 has plotted the distribution of Laves phases as a function of the radius ratio, ?A/rB, and found that, while the distribution extended from 1.05 < rA/B < 1.50, the

Jan 1, 1965

By A. H. Heim

A method and apparatus for measuring gas porosities of rocks are described. The apparatus can be assembled from commercially available components. In principle, measurements are made by volume substitution at constant pressure. The maximum error is not more than 0.3 porosity per cent. Typical results are given. INTRODUCTION Determining the porosity of rock samples is one of the most important and yet most varied types of measurement in core analysis. Among the many techniques devised are the so-called "gas porosity" methods. An old and well known example is the Washburn-Bunting method.&apos; The U. S. Bureau of Mines2-&apos; described and later improved the apparatus for a now widely used method generally known as the "Boyle&apos;s law" method. In the present form of the Washburn-Bunting method,&apos; the volume of air in the pores of a rock sample at atmospheric pressure is extracted and then collected in a graduated burette at atmospheric pressure. The volume of air is read directly as the pore volume of the sample. The absolute error in reading the collected volume of gas is independent of the total volume; thus, the relative error is larger when the volume is small, as it is for rocks of low porosity. In addition, the sample after measurement contains mercury, which limits its use for other analyses. The Bureau of Mines (or Boyle&apos;s law) method measures directly the solids volume of a sample from which the pore volume and porosity are derived, using a separate measurement of the bulk volume. Gas at a few atmospheres pressure is introduced into a sample chamber of known volume containing the rock sample. The pressure is accurately measured. Following, the gas is expanded into a burette at 1 atm, and the gas volume is read directly. From the initial pressure p, and the final pressure p2 and volume v,, the initial gas volume v1 is calculated using Boyle&apos;s law; that is, p1v1 = p2v2. Volume v, minus the volume of the empty sample chamber is the solids volume of the sample. The accuracy of the method is limited, unless corrections are made, by deviations of the gas from the "ideal" gas-law behavior assumed in the simple form of Boyle&apos;s law. The purpose of the present paper is to describe a method for measuring the gas porosity of a rock which avoids many of these difficulties. Gas volumes are measured directly with the same accuracy as the bulk volumes. Pressures of at least an order of magnitude larger than those of previous methods are employed to insure rapid penetration of the gas into the sample. While special equipment may be built to apply the method, the porosimeter may be constructed as well from commercially available components. For simplicity, the apparatus described will be referred to as the "Constant-Pressure gas porosimeter". THE CONSTANT-PRESSURE METHOD Fig. 1 shows schematically the arrangement of components comprising the present Constant-Pressure porosimeter. Briefly, the method is one of volume substitution and may be considered a null measurement. Omitting (for the present) some of the operational details, the method of measurement consists of the following three steps. 1. After evacuation, the volume of the measuring system (a ballast chamber, a manifold, two gauges and their connections) up to the sample chamber is filled with gas to a high pressure (- 1,000 psi). A sample of the gas at this pressure is trapped in one side of a sensitive differential pressure gauge to serve as the reference pressure for subsequent steps. 2. The evacuated sample chamber containing the rock sample is opened to the measuring system. As the gas expands into the chamber, the resulting decrease in pressure unbalances the differential pressure gauge. 3. The pressure is restored by means of a mercury volumetric pump. The volume of mercury injected exactly equals the free or void volume of the sample chamber (volume of empty chamber minus the solids volume of the rock within). From the injected volume and the known empty chamber volume, the solids volume is obtained and the porosity calculated. The pressure and the volume occupied by the gas are the same before and after opening the sample chamber. Expansion and compression of the gas are incidental operations and do not enter into the calculation of porosity. By the pressure balancing or nulling, the free volume of the sample chamber is merely substituted by an equal and measured volume of mercury. Since the measurements are at constant pressure, there are no compressibility corrections necessary for the sample chamber.

By B. Ramaswami, U. F. Kocks, B. Chalmers

The latent hardening of silver and an Ag-Au alloy was investigated by lateral compression, overshoot in tension and cormpression, and the stability of multiple-slib orientations. The latent hardening of a secondary slip systenz depends on its relation to the primary slip system. For most secondary slip systems the latent hardening is larger for Ag-10 at. pct Au than for pure silver. The maximum increase in. flow stress on a secondary slip system over that of the primary slip system was 40 pct. The work hardening during the lateral-compression test on the latent system after prestress on the primary system is iuterbreted in terms of the preferential distribution of barriers to dislocation movement with respect to the active slip system in work-lzardened fcc crystals. The work-hardening in fcc crystals is mainly due to the dislocation interactions and the barriers to dislocation movement formed as a result of reactions between dislocations of different slip systems. The operation of sources on the latent system depends on the flow stress of those systems; hence, the increase in flow stress of a latent system due to glide on an active system, which is called latent hardening, is an important element in understanding the phenomenon of work hardening. The problem of latent hardening has attracted the attention of many investigators in the past. For example, a theoretical study of the elastic latent hardening of the latent systems due to glide on an operative system has been made by Haasen&apos; and ~troh. These calculations, however, neglect the stress required for the intersection of forest dislocations by the glide dislocations, a factor which would be important for producing macroscopic strains on the secondary slip systems. The importance of this factor will become evident from the results presented here. Attempts have also been made to determine the latent hardening of different slip systems by experimental means by the methods summarized in Table I.3-9 The experimental methods used have been subject to certain limitations. For instance, in the method used by Hauser,9 frictional constraints between the specimen and the compression platen were not eliminated by proper lubrication (see Hos- ford10). Secondly, with the exception of Kocks,6 Hauser,9 and Rohm and Kochendorfer,11 latent-hardening studies have been made on only one of the slip systems, i.e., on either the conjugate or the coplanar slip system; hence, extensive results are not available on the latent hardening of different slip systems in the same materials, with the exception of aluminum.6 It was therefore decided to study the latent hardening of the conjugate, critical and half-related slip systems in silver. Similar experiments were done in Ag-10 at. pct Au to study the effect of solute (gold) on the latent hardening of silver. Lastly, indirect evidence can be obtained by a study of the orientation stability of crystals of multiple-slip orientations in tension and compression. This method has been used by Kocks6 to supplement his studies of latent hardening in aluminum. Similar studies were made at room temperature in single crystals of silver. EXPERIMENTAL PROCEDURE The single crystals of the desired orientations were grown and the tensile test specimens were prepared as described in Ref. 12. The compression tests were made on 1/4-in.-cube specimens. The specimens were cut from single crystals, in the Servomet spark-erosion machine.13 The two cut surfaces were planed using the lowest available planing rate in the machine to minimize the deformation layer. A brass strip was used as the planing tool. This method of preparation ensured plane parallel faces for the compression tests. The deformed material was removed by prolonged etching in a weak etching solution. A weak etching solution was used to prevent pitting of the surfaces and to ensure uniform etching. About 25 to 50 µ of material were removed from all faces by the etching treatment. The specimens were then annealed for 24 hr at 940°C in oxygen-free helium and cooled in the furnace to room temperature over a period of 7 hr. After annealing, the orientation of the specimens was determined by Laue back-reflection technique to make sure that no recrystallization had occurred on annealing. The compression-test technique and setup are described in Ref. 14. The Laue back-reflection technique was used to study the overshoot in tension, the overshoot in compression, and the stability of the axial orientation in tension and compression. The tests were interrupted after every few percent strain to determine the axial orientation. In investigating the overshoot in compression, the operative system was determined by studying the asterism of the Laue spots.

Jan 1, 1965

By Thomas M. Chatard

Every one engaged in the mining of phosphates is well aware that the price he gets for his product depends upon tile results of chemical analysis. He knows that the value rises with the percentage of phosphoric acid, whether stated as such or as so-called " bone phosphate," and that deductions are made for certain constituents, such as alumina or oxide of iron, when the amount of these exceeds certain limits. The reason for these deductions is but vaguely understood by many, and there are few who possess the special knowledge required to form a competent judgment, either as to the reli-

Jan 1, 1893

By W. H. Schacht

IN THE Lake Superior District, the air indoors must be heated continuously during eight months of the year and occasionally during the remaining months. Incident with mining in this district, therefore, there is need for heating many of the buildings connected with these operations. In addition to the mine buildings, that is, shops, engine, houses, offices, change houses, etc., such public buildings as schools, library, and theater, when close to the mines, are often supplied from the mine heating mains. At the Copper Range Company&apos;s mines, Champion, Trimountain and Baltic, the heating surface thus supplied from the mine mains is over 50,000 sq. ft. (4645 sq. m.) which requires a steam consumption, at times, of 18,000 lb. (8165 kg.) per hour, or the equivalent of a rate of over 50 tons of coal per day (were live steam used). This figure is based on a consumption of 1/3 lb. per square foot of heating surface during the coldest weather, and provided the system is not wasting steam by blowing it to the atmosphere or into the return line on account of leaky traps, which so often is the case. Under the latter conditions, steam consumptions of three to four times the above rate are not uncommon. This shows that the cost of heating is of enough importance to be given serious consideration, especially at this time of rising prices of fuel. The power and heating value of exhaust steam are appreciated by most engineers, and its application for such purposes is general. At our stamp mills, the exhaust from the stamps is used to operate low-pressure turbines, thus reducing the former water rate per horsepower developed by more than 50 per cent.

Jan 8, 1920

By Frank Speller

WE are here to honor again the memory of Henry Marion Howe, one of the foremost metallurgists of his time, and it is indeed a great privilege to be called upon by the Board of Directors of .this Institute to give the memorial address this year. Professor Howe started active investigation of corrosion of iron from a metallurgical standpoint in 1887, and made several important contribu-tions to the subject from 1895 to 1908.(1) ? The papers named in the bibliography are only a few of his valuable papers, but in all his works he sets a high standard of scientific accuracy, together with a clearness and power of expression rarely equaled in engineering literature. There-fore it seems appropriate on this occasion to review the work on corrosion of this distinguished gentleman and then endeavor to make a brief inventory of what has been accomplished since his time. Howe saw the beginning of the steel industry in America and before he died (May 14, 1922) witnessed it develop to a production of 45,000,000 tons per year. He was naturally very much interested in the infant industry and was quick to see the importance of the question of corrosion. It was my privilege to discuss the subject of corrosion frequently with Professor Howe at various times from 1905 to 1908; in this, as in other metallurgical problems, he sought the truth without bias and always insisted on proving an opinion or conclusion before accepting it. We should remember that when Howe started his investigation of corrosion, in 1887, steel was rapidly supplanting wrought iron. Certain papers in the early eighties (now forgotten) claiming much greater durability for wrought iron than for steel aroused Howe&apos;s interest. He could not reconcile the statement that steel was intrinsically and incurably less durable than wrought iron with the continued and widening use of steel,

Jan 1, 1934

By J. Campbell

The negative pressure developed within a solidifying sphere of pure iron is investigated theoretically assuming an elastic-plastic model. The maximum hydrostatic tension attainable is shown to be an order of magnitude smaller than that required for the homogeneous muclealion of pores in the liquid cove, and four orders of magnilude smaller than that predicted from) a rigid shell model. It is well-known that liquids can withstand large hydrostatic tensile stresses, or negative pressures. The various experimental investigations of the tensile strengths (often called the fracture pressures) of liquids are reviewed by Dean,1 and the theoretical attempts at estimating fracture pressures are critically assessed by wakeshima.2 Using Fisher&apos;s3 quation, the fracture pressure of pure liquid iron is about -70,000 atm, which may be too large by as much as a factor of 4, but is certainly correct to within an order of magnitude.&apos; In view of the great importance of the problem of the nucleation of shrinkage cavities in castings it is of interest to determine exactly what tensile stresses can exist in the residual liquid in a solidifying casting; it has often been assumed that, because of the very low strengths of solid metals near their melting points, no interior stresses are developed at all. Nussey4 has determined theoretically the pressure in the liquid core of a solidifying metal sphere assuming that the solidified shell does not deform (i .e., is perfectly rigid), so that because of the contraction accompanying solidification (a) (about 3 pct for most metals) the progressive deposition of solid onto the inner surface of the shell causes the remaining liquid to be expanded to make up this difference in volume. This leads to a relation between the pressure P in the liquid, the initial pressure, PO, the bulk modulus of the liquid, K, and the inner and outer radii of the solid shell, o and b, respectively:

Jan 1, 1968