Search Documents

By C. A. Hansen

Page Introduction............................206 Power Characteristics in Zinc Sulfate Electrolysis........... 207 Current Efficiency......................... 207 Corrosion Rates..........................216 Voltage Required by the Zinc Cell..................219 Power Requirements of the Zinc Cell ................221 Impurities in Zinc Electrolyte.....................222 Non-cumulative Impurities.....................223 Cumulative Impurities ....................226 Impurities in General........................228 Temperature and the Stability of the Zinc Cell..............229 Practical Expedients for Control of the Zinc Cell...........234 Acknowledgments...........................234 Appendix................................235 Discussion...................:.......... - 236 Introduction It has been the experience of the writer, during some five years' work with electrolytic zinc, that the zinc cell is perhaps more sensitive to impurities in the electrolyte than the analytical methods as yet developed for the chemical identification and determination of these impurities; but that, when proper purification methods have been applied to a given solution, the behavior of the cell is quite independent of the original sources from which the zinc sulfate has been derived. It has also appeared that the behavior of the zinc cell is the best and surest check on the correctness and thoroughness of the purification methods used, because it indicates the presence of both current impurities and cumulative impurities derived from the leaching of the ore; it also indicates whether these impurities are current or cumulative, at least in so far as they are of serious importance commercially.

Jan 1, 1919

By Samuel G. Lasky

FAULTING at Kennecott, with its attendant fracturing, is unusual, complex, and important. As study and knowledge of the various fault systems have progressed, appreciation of that importance has helped in the selection of proper horizons for exploration and in the avoidance of useless crosscutting and drifting. During the study of this faulting and fracturing, a suggestion concerning the formation of the ore-bearing fissures occurred to me. Further study in the available portions of the approximately 45 miles of workings in the Kennecott mines for the purpose of checking up the the suggestion led to the hypothesis which this paper will attempt to present. Briefly, the hypothesis may be stated as follows: The formation of transverse faults that stop against a main system is connected with changes in the strike or dip of the main fault, and such cross faults or fractures lie in the moving block of the main fault system and indicate a change in strike or dip of the main fault. It has been found that each kind of change tends to produce definite effects and that careful study of the evidence can often suggest the exact type of change. Outline of Kennecott Mines Geology The mines at Kennecott are on the northeast flank of a broad anticlinell where erosion has exposed the Upper Triassic Chitistone limestone resting conformably on the Permian or Triassic Nikolai greenstone.2 These two are the only formations exposed in the immediate vicinity of the mines that bear relation to the ore deposits. The Nikolai greenstone is a series of altered basaltic lava flows, the actual thickness of which is unknown. The Chitistone limestone is the ore-bearing formation. At its base is a bed of about 5 ft. of red, green, or black shale which shows strong evidence of movement wherever it is exposed underground—one of the

Jan 1, 1929

By P. Gianella Vincent

Barite deposits are of widespread occurrence in Nevada but there are few pro-ducing properties; most of the latter are in northern Nevada. The production of the state is small at present-in the neighborhood of 15,000 tons annually-but is steadily increasing. The barite occurs in veins and also as replacement deposits in lime-stone. The bulk of the production has come from the replacement deposits. It is thought that the barite was deposited from rising hot waters similar to-and probably contemporaneous with-those responsible for some of the metallic ores of the state. This paper discusses only the deposits in northern Nevada. THE commercial mining of barite did not begin in Nevada until 1916 but although the production has been small there has been a rapid increase in tonnage during the past several years. Barite is widely distributed in the state and production comes from at least nine of the seventeen counties. Apparently this is not generally known, as only two counties are mentioned in a recent publications dealing with barite. The increase in output is due largely to recently discovered barite deposits in northern Nevada. The principal production has come from the northern portions of Lander and Eureka counties; smaller amounts from Elko County. The discussion in this paper is confined largely to the deposits in these counties. Most of the producing area is tributary to the Western Pacific and Southern Pacific Railroads, whose tracks lie along the Humboldt River. Barite is known from other northern counties but so far the production has been small. The output has come entirely from veins and replacement deposits, the latter largely in sedimentary rocks. In general, the barite from veins is white; that from the replacement deposits usually is dark gray to black, although some is light gray or white. Most of the veins contain sulphides and many barite-bearing veins have been worked for their content of base or precious metals.

Jan 1, 1940

By D. D. Smith, D. P. Squier, E. L. Dougherty

A system of differential equations describing the temperature behavior of fluid injected at constant surface temperature in a well is derived and .solved analytically. A formula for the fluid temperature at any time and depth is given, as well us a special formula valid for very large times. These formulas are used to calculate temperatures for several typical cases. The results indicate that, initially, the temperature of the water entering the formation is considerably lower than the injection temperature. This condition lasts for only a short period— less than three days for most cases of practical interest. Following this highly transient period, during which the temperature of the fluid entering the formation builds up to about 50 to 75 per cent of the injection temperature. the system enters a quasi-steady state in which the temperature changes are very slow. After severl years, the bottom-hole temperature will still be 50" to 100°F lower than the injection temperature, hilt the heat losses may he tolerable. INTRODUCTION Predicting the behavior of a hot-water flood requires that the temperature of the water entering the injection interval be estimated. This report describes the development and solution of a system of equations which describes the temperature behavior of the injected water in the wellbore with certain simplifying assumptions. The only previous means known to the authors for describing such a process is that of Moss and White.' Their results appear to be close to those obtained by our method in the practical cases which were compared; this agreement is largely due to the fact that in our method temperature soon approaches a quasi-steady state, as was assumed in their method throughout. However, our model covers all times, is continuous (whereas the Moss-White model depends on breaking the depth into discrete intervals) and. we feel. more closely describes the physical problem. FORMULATION OF THE PROBLEM PHYSICAL SYSTEM AND ASSUMPTIONS The injection procedure consists of pumping water at a fixed surface temperature T., down an infinitely long cylindrical well or tubing of inner radius Any material exterior to the water column such as mud, casing, or cement is regarded as part of the formation. The general behavior of the system may be described qualitatively as follows. When the hot water is first introduced into the system, the temperature difference between the formation and the water is large, resulting in a high rate of heat transfer. As a result, the temperature adjacent to the wellbore rises very quickly. Because the segment of the formation adjacent to the wellbore largely controls the heat transfer rate, the heat transfer rate will become relatively constant when this portion has reached a temperature close to that of the water opposite it. The temperature of the water and formation then increase very slowly with time. The length of the initial highly transient period and the temperature of the water at its conclusion will be functions of depth, injection rate, injection-string radius, surface injection temperature and the physical properties associated with the water-formation system. The following additional assumptions were made. 1. There is no heat transfer by radiation in the system. 2. There is no heat transfer by conduction in the vertical direction in either the injection stream or the formation. 3. The linear volumetric and mass flow rate of the water is constant throughout the injection stream. 4. No horizontal temperature gradient exists in the injection stream. 5. The product of density and heat capacity is constant for both the water and the formation, and the formation thermal conductivity is constant. 6. Initially, both the water in the wellbore and the reservoir are at a temperature given by the (constant) ambient surface temperature plus the product of depth and geothermal gradient (assumed constant). At large distances for the wellbore (r m), the formation will remain at this temperature. 7. The water temperature and the formation temperature at r — r,, are equal for all depths D. DERIVATION OF EQUATIONS The differential equation satisfied by the fluid temperature T,(D, t), which is obtained by writing a heat balance on a cylindrical differential of volume dV of the injection string between the depths D and D i dD, is

By William I. Gardner

Optimum design of a structure obviously requires a thorough knowledge of the materials to be utilized in its construction. When the structure is a tunnel, a most important element in its design and construction is the geology. As a tunnel may be many miles in length and at depths of hundreds or thousands of feet, we face a real problem to meet the needs of the designer and builder. How can we determine the properties of our construction materials in this situation? Engineering geology has had a formidable challenge to meet the requirements of conventional excavation methods; the advent of machine methods for rapid excavation compounds the requirements for more detailed and more precise geological knowledge of the tunnel site. This chapter will discuss the means now at our disposal to meet the challenge to produce the required data on the tunnel site in the preconstruction stage. Our considerations will be directed towards construction of a free-flow tunnel, primarily in fractured rock formations, without any requirements for the rock mechanics type of in-situ tests that might be made for a pressure tunnel or for a large opening for an underground power plant. In essence the investigation must determine: (1) The geologic conditions affecting the type of construction equipment and excavation method of the rock to be broken and removed. (2) The quantities of water and gas to be encountered. (3) The strength and stability of the material surrounding the bore and its need for support and lining. GEOLOGICAL FACTORS AFFECTING TUNNEL DESIGN AND CONSTRUCTION The engineer or contractor may classify the rock as either competent or incompetent or more pointedly as "good" or "bad" ground. The geologist may bestow a precise petrographic name upon the rock, such as granodiorite or indurated tuff breccia or name the formation, as Mancos shale, for

Jan 1, 1970

By R. L. Pober, L. Kaufman, E. V. Clougherty

Composite structure of hafnium, zirconium, and titanium diboride with additions of metals and/or compound phases were prepared by reactive high-pressure hot pvessing and evaluated in air and in mixtures of oxygen and helium at temperatures up to 2400°K and at linear flow rates of 0.1 to 0.2 ft per sec stp. Oxidation characteristics, principally depth of conversion of diboride to dioxide, were determined by a gas analysis method and by postoxidation metallo-graphic analyses. The best oxidation resistance was observed for hafnium diboride-silicon carbide composite which exhibited a 6-mil conversion to dioxide for a 1-hv oxidation in air at 2200°K compared to a 20-mil recession for hafnium diboride with no additive. Analogous improvements in oxidation resistance were observed for the addition of silicon carbide to zirconium. EARLIER investigationof the oxidation behavior of the diborides of the transition elements of Groups IVA and VA in flowing gas mixtures have produced a ranking of these compounds according to which HfB2 is the most oxidation-resistant followed in turn by ZrB2 > TiB2 > TaBz > NbB2. Other ~tudies~-~ have examined the physical, thermal, and thermodynamic properties of these diborides to provide a sound basis for the more detailed and specialized investigations which are required to generate the information needed to assess the usefulness of such materials in high-temperature oxidizing environments. Recent oxidation studies7 have examined the effect of variations of metal and boron content on the oxidation characteristics of zirconium and hafnium diboride in flowing gas mixtures including air and helium plus oxygen. Results obtained in the latter investigation confirmed the superior oxidation resistance of HfB2 over ZrB2. Moreover, metal-rich compositions of hafnium diboride showed improved oxidation resistance over boron-rich compositions at temperatures up to 2000°K; at higher temperatures the differences are not distinguishable. In particular HfBI.7 exhibited a diboride to dioxide conversion depth of 4 mils in 1 hr at 2000°K; HfB2. 2 exhibited a conversion depth of 16 mils for the same exposure.~ Specimens for the study of metal and boron stoichiometry on the oxidation characteristics of HfB2 and ZrB2 were prepared by high-pressure hot pressing, a specialized type of fabrication which produced dense crack-free bodies of the desired compositions with no significant impurity introductions. The purpose of the present investigation was to explore the possibility of further improving the oxidation resistance of the metal-rich ZrB, and HfB2. The plan to accomplish this objective was based in the formulation of several diboride compositions containing other compounds and phases which are generally known to have good oxidation resistance in one or more types of test environment. Ideally, such additives would also enhance or at least not diminish other boride property values principally mechanical strength and those parameters related to thermal stress resistance. The additions selected for HfBz included zirconium, aluminum, and (Ta + TaB2) designed to produce ternary metal diborides, hafnium to form a discrete HfB phase, chromium to provide a metal skeletal phase, (Hf + Si) to form a discrete hafnium silicide phase, and Sic to provide a discrete second phase. Additions to ZrB2 included A1 + B designed to produce a ternary metal diboride, Zr + Si to form a discrete zirconium silicide phase, and Sic to provide a discrete second phase. All the specimens were prepared by high-pressure hot pressing which was used to advantage to fabricate billets of the variety of compositions desired and suitable for oxidation testing. The present investigation also included the evaluation of high-pressure hot-pressed TiB2and TiB2-20 vol pct Sic, conventionally hot-pressed Boride 2,' and KT silicon carbide. Boride

Jan 1, 1969

By Richard E. Ellwanger

Methods of utilizing flocculents as settling and filter aids for mineral processing slurries are reviewed. Broad chemical classifications and techniques for proper dilution, multiple addition, and combination treatments are discussed. A variety of custom built and commercially available systems for makeup and delivery of flocculents to the application points are in use throughout the mining industry. Those concepts which, in the author's opinion, are particularly important to the successful makeup and we of flocculants are presented in relationship to the available makeup and feed systems. Actual industrial applications are included in the presentation.

Jan 1, 1982

By Cyril Stanley Smith, Earl W. Palmer

A STUDY of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors' conclusions regarding graphitization. MATERIAL USED After some preliminary heats had been made in the laboratory to determine the effect of copper, several castings from commercial air-furnace heats were obtained, and data from these alone are given here. Part of the metal was poured directly and part was treated in the ladle with the desired amount of copper before pouring. Green-sand molds were used, each holding two tensile test pieces of the form adopted by the Malleable Iron Research Institute, or two bars for graphitization studies, 5/8 in. in diameter and 9 in. long, fed through two enlarged sections equidistant from the middle and ends of the bars. Risers of suitable size insured sound castings. Tensile tests were made

Jan 1, 1935

By N. S. Keith

It seems proper, before describing the plant which has been erected in Rome, N. Y., for the purpose of demonstrating the practicability of my process of refining and desilverizing lead by electrolysis, to state in a few words the principles that govern the process. They are well known to those who have studied electrical science, and to the practical electro-platers of the country, and are briefly these: If we take a plate, or other form, of metal (impure lead in this case), and immerse it in a bath consisting of a solution of the main metal (that which contains the impurities), and also immerse another plate, which shall be a conductor of electricity, in the bath, but separated from the first by the solution, and connect the former plate with the positive pole of the source of electricity, and the other plate with the negative pole, an action will go on in this bath which is called electrolysis. There is first a decomposition of the solution constituting the bath ; then a solution of the metal at the positive pole (called the anode), and a deposition upon the other plate connected with the negative pole. which plate is technically called the cathode. If the bath is properly constituted, and the current of electricity which is passed through the bath is of the proper strength and electro-motive force, the dissolution of the anode and the deposition of the metal upon the cathode will be exactly equivalent. The analysis and synthesis are opposite and equal. If, on the other hand, this solution (called an electrolyte) be not properly constituted, decomposition will go on, but there will be these effects: a superoxidation at the anode and a liberation of free hydrogen at the cathode, which free hydrogen escapes finally in bubbles through the liquid to the surface, and into the atmosphere. In the electrolytic treatment of metals simply for their purification and recovery, it is

Jan 1, 1885

By R. D. Pehlke, J. V. Gluck

The effect of small additions of silver on the actiziity of zinc in dilute solution with molten bismuth has been determined ill the range 450° to 650°C. Experimental measurements were made in a multi-electrode galvanic cell. All zinc activities showed large positive deviations from Raoult's Law. The results are expressed in terms of the interaction parameter EJ, as defined by Wagner. In the binary Zn-Bi system, Henry's Law was followed at zinc concentrations below 5 mol pct, thus indicating that the binary or self-interaction parameter of zinc in bismuth is essentially zero. The Henry's Law con- THE determination of thermodynamic interaction parameters requires accurate knowledge of solute activities in the dilute-solution region. Dealy and Pehlke1 have summarized the basis for interaction relations, discussed some theoretical implications, and presented a compilation of interaction parameters calculated for molten nonferrous alloys from stant ranged from 2.43 at 650°C to 3.96 at 450°C. The binary zinc activities were consistent with published data for higher zinc concentrations . The ternary interaction parameter ranged from -1.90 at 650°C to -3.30 at 450° C, varying linearly with the reciprocal of the absolute temperature. The negative value for the parameter reflects the fact that addition of silver decreases the activity of zinc in solution with bismuth. data available in the literature. Most of the data were for two-component systems from which only the self-interactions, Ei, could be calculated. Concentration ranges were often such that a considerable extrapolation was required for calculations at lnfinite dilution. The data for ternary systems were quite limited and often unavailable in suitable systematic fashion—thus few values of the parameter e| could be obtained. Knowledge of both the binary and ternary interaction parameters is necessary for the estimation of the activity coefficient of a given dilute solute in

Jan 1, 1965

By Angelus S. C. Owili-Eger

This paper discusses a model for groundwater quantity prediction at operating sections of underground mines. The approach involves the development of a mathematical model for the movement of water through an integrated (unsaturated-saturated) flow domain within a definable watershed. The model is programmed for the IBM 370/168 computer using the method of finite difference approximation coupled with a finite element analysis. The conceptual and computational aspects of the model have been validated with both experimental and field data and applied to an active coal mining operation located in central Pennsylvania.

Jan 1, 1977

IF you wish to make the acid that is vulgarly called common aqua fortis,* for parting gold from silver, you must first provide as many cucurbits and alembics, receivers, and materials as you wish, and then make a furnace that is long and conveniently wide for holding three or four pairs of cucurbits or as many as you wish. If you have to make this by art in order to work a large quantity, you could make several small furnaces for it seems that not more than three or four pairs are suitable for one. Prepare the places where the cucurbits are to stand with bottoms or covers made of potter's clay or tiles that are half round like the bottoms of the cucurbits and have a little rim around the top so that they can be built in. Proceed to build these in in pairs, one by the other with convenient spaces between, placing an iron support across to make this place stronger and more secure. In every corner and also in the middle a hole must be made as a vent for the smoke, as is done in all furnaces. You will see the form of this somewhat roughly drawn here. [Figure 25] Near this prepare a number of cucurbits which are made of glass, as clear and uniform as possible and very well formed. There must be no bubbles or other indentations in these, for they would be dangerous and uncertain for your work. Lute these with lutum sapientiae up to within three dita or less from where the neck narrows. This lute must be spread out well all over to the thickness of two threads or a little more. Then cover and make them strong with this well-made plaster, and finally dry it, taking care that there are no clefts or cracks such as clays are often prone to make even though they be well prepared. For greater security choose among these [64v] a clay that is lean and then mix it with at least a fourth part or more of wool-clloth clippings and about an eighth part of wash

Jan 1, 1942

By M. Lastra, A. Cruz, J. Menacho

The technical feasibility of treating exotic copper ore with an acid cure using concentrated H2S04 is studied. Applications in a conventional percolation leaching circuit for unaltered ore and in a conventional agitation leaching circuit for altered ore are examined. The main effects of an acid cure are to inhibit silica dissolution and to increase the sedimentation rate of agitated pulps. An increase in the rate and degree of copper extraction is also observed. Based on these results and the minimal additional investment required, acid curing appears to provide an excellent approach for treating exotic copper ores.

Jan 1, 1980

By Erwin H. Leeman, Raymond R. Rice, Gerald L. Hassler

In the past few years a great deal of preeise information has been obtained about the relation of natural gas to oil production1. The improvement of our understanding has been of great value, both in prolonging the life of wells and in providing a much needed technical background for the legal problem of proration. But there are two principal aspects of the problem of production. It is necessary to consider not only the energy available, in the form of compressed and dissolved gas and in the pressure of driving water, but also the tenacity with which the sandstone holds the oil. The amount of oil that each sand condition will produce under given conditions of gas content should be determined. Hitherto the effect of the sand has been judged by a study of the flow of each well coupled with a procedure for extrapolating the production curve; hut, as is well known to evaluation engineers, such production curves are subject to changes that are not well understood, and often are affected by outside disturbances. On the whole, the concept of "potential production" is vague principally because the influence of the sand in production is not known beyond the simple ideas of porosity and permeability. The permeability is a quantity that has only inference value where mixtures of gas and oil or of gas, oil and water are present. Excellent studies of the production of oil from reservoirs packed with unconsolidatcd sand are available2, but these studies treat largely of small-scale analogzes to a producing field, and the conclusions to be derived from them arc necessarily of a qualitative character because it is not known in what way these miniature oil fields resemble large ones.

Jan 1, 1936

By Thomas C. Atchison

An understanding of the physical processes involved in breaking rock with explosives will lead to better blasting techniques. In this chapter known rock breakage principles will be outlined, some conjectural ideas will be discussed, and areas needing further study will be pointed out. The principles outlined will serve as a basis for the design of blasting rounds described in the following chapter. 7.2-1. Factors Important to Rock Fragmentation. The efficacy of explosives as tools for rock fragmentation lies in their ability to deliver almost instantaneously large amounts of energy to a limited portion of the rock. When an explosive charge is detonated in a drill hole, its energy is released in a very small fraction of a second in the form of gas at extremely high pressure and temperature. The mechanics of the transfer of this energy to the rock and the resulting breakage are complex and not completely understood. Factors that have been identified as important to the fragmentation process may be grouped in three categories: explosive parameters, charge loading parameters, and rock parameters. EXPLOSIVE PARAMETERS. Explosive parameters known to influence breakage are density, detonation velocity, detonation impedance, detonation pressure, gas volume, and available energy. Detonation pressure is probably the best indicator of an explosive's ability to break solid hard rock. Detonation pressure is roughly proportional to the product of density and the square of the detonation velocity. The relative ability of different explosives to transmit their pressure to stress in a given rock is function of their detonation impedances. Detonation impedance is the product of density and detonation velocity. The volume of gas released in the explosive detonation undoubtedly is of importance, at least in the later stages of breakage, and is probably

Jan 1, 1968

By William Fink

ALUMINUM forms not only binary compounds with most of the metallic elements but also forms many ternary or more complex constituents. Several of those occurring in the more important alloy systems have been identified under the microscope and the action of various etching reagents has, been carefully studied.' The determination of the structure and composition of these complex constituents is a matter of some difficulty and little information is available. X-ray crystal analysis offers a promising method for the study of such constituents. First, and of considerable importance, is the possibility of recognizing the presence of a given constituent by means more positive than microscopic observation. Evidence can also be obtained concerning the nature and composition of the constituent in question and ultimately it should be possible, at least in some cases, to describe the structure including the relative locations of the various atoms. In this paper some results of an uncompleted study of the constituents of the aluminum-iron-silicon system are given and the methods employed are described. Inasmuch as iron and silicon are the chief impurities in aluminum, the constitutional relations of this system are of fundamental importance in the metallurgy of pure aluminum and its alloys; the system has been studied by several investigators and the more important contributions have been reviewed recently.2 Fig. 1 shows the structure of the aluminum-rich alloys after prolonged annealing at 560° C., in accord with one of the most recent investigations.3 The ternary alloys examined in the course of the present investigation were all annealed at 550° or 560° C.; in fact, some of the specimens were the identical ones used by Dix and Heath, who kindly supplied them for this work. Since the results

Jan 1, 1930

By Erwin H. Leeman, Raymond R. Rice, Gerald L. Hassler

In the past few years a great deal of preeise information has been obtained about the relation of natural gas to oil production1. The improvement of our understanding has been of great value, both in prolonging the life of wells and in providing a much needed technical background for the legal problem of proration. But there are two principal aspects of the problem of production. It is necessary to consider not only the energy available, in the form of compressed and dissolved gas and in the pressure of driving water, but also the tenacity with which the sandstone holds the oil. The amount of oil that each sand condition will produce under given conditions of gas content should be determined. Hitherto the effect of the sand has been judged by a study of the flow of each well coupled with a procedure for extrapolating the production curve; hut, as is well known to evaluation engineers, such production curves are subject to changes that are not well understood, and often are affected by outside disturbances. On the whole, the concept of "potential production" is vague principally because the influence of the sand in production is not known beyond the simple ideas of porosity and permeability. The permeability is a quantity that has only inference value where mixtures of gas and oil or of gas, oil and water are present. Excellent studies of the production of oil from reservoirs packed with unconsolidatcd sand are available2, but these studies treat largely of small-scale analogzes to a producing field, and the conclusions to be derived from them arc necessarily of a qualitative character because it is not known in what way these miniature oil fields resemble large ones.

Jan 1, 1936

By L. B. Slichter

IT has been estimated that rock exposures in most mining districts aggregate less than 1 per cent. of the total surface area.1 Conclusions concerning the hidden 99 per cent. necessarily have been based on knowledge of only a small fraction of the surface, and from this limited information the geologist has been obliged to deduce the approximate and general nature of the underlying formations. In the search for ore it is necessary to supplement this general picture with greater detail. Fairly accurate knowledge of relatively small zones is required. This knowledge is carefully sought in many different ways-detailed interpretations of geological history, the tracing of float, the use of test pits, of trenching, of drilling, and of other methods. Practical ingenuity, scientific brilliance, great perseverance and patience, and the expenditure. of large sums of money have all been a part of this search. The problem of exploring beneath cover with economy, and of obtaining essential information which this cover hides, is obviously a difficult one. It is also a very important one, for geologists inform us that already the story of the 1 per cent. exposed outcrops has been largely read.2 There remains the nearly virgin field comprised in the hidden 99 per cent., and the importance of this zone is bound to increase continually. In recent years, the problems connected with the exploration of this "99 per cent. zone" have attracted a constantly enlarging group of investigators and at present greater efforts than ever before are being made to resolve then. This work, in its various special aspects, has enlisted, beside geologists, the cooperative efforts of chemists, physicists, and mathematicians. The progress made in this development should be kept before those directing explorations in order that due advantage may be taken of a changing situation.

Jan 1, 1928

By H. E. Nold

THE raw materials of the ceramic industry are mostly clays. This raw material is ground, water is added and the mixture pugged into a moist, plastic, rather stiff mass. From this mass the desired units of manufacture are made (bricks, hollow building tile, sewer pipe, etc.). These units are dried; then placed in kilns and heated until the desired degree of vitrification is obtained.1 For firing ceramic ware, two distinct types of kilns are used; namely, periodic and continuous tunnel. PERIODIC KILNS Periodic kilns are those ordinarily seen in a brick plant. They are either round or rectangular. The raw, dried, formed ware is piled or set in the kilns to depths frequently exceeding 10 ft. The kiln is heated until the ware is matured, then gradually cooled sufficiently to allow men to remove the ware; then the cycle is repeated. The time duration of the cycle may be more than two weeks. In order that heat can be distributed uniformly throughout the pile or setting, the units are placed so as to leave open spaces or flues through-out the pile for the passage of the hot gases. Each kiln is provided with a number of fireboxes (usually 10 or 12) spaced equally in the outside wall. The fireboxes may be equipped with flat or inclined grate bars or they may have no grates at all (dead bottom). Down-draft kilns are most used. In these the hot gaseous products of combustion from the fireboxes are deflected upward by bag walls just inside the fire zone. From the top of the kiln the gases are drawn down through the setting, off through holes in the kiln bottom, and conducted to a stack or stacks. In up-draft kilns the fireboxes are usually set somewhat lower. The hot gases are drawn inward and upward through the ware and pass off from the top. Up-draft kilns find their greatest use in the firing of common brick. In either case the problem is to maintain, as nearly as possible,

Jan 1, 1933

By M. E. Wadsworth, K. J. Richards

The oxidation rates of tantalum in various partial pressures of carbon dioxide in the temperature range 700°to 950°C were measured with a thermo-gravimetric balance. Oxidation involved a surface -controlled reaction associated with the formation of a nonprotective layer of Ta2O5. Below about 720°C, there was a change in the rate-determining mechanism, and above 830°C the linear rate was preceded by a complex region of nonlinear oxidation behavior. The linear oxidation of tantalum has been explained quantitatively in terms of carbon dioxide adsorption, followed by a rate-controlling surface reaction. The initial adsorption has been expressed both as an equilibrium process and as a steady-state reaction. The enthalpy for chemisorption of CO, was determined to be -17.3 kcal per mole. The surface-controlled reaction had an activation enthalpy of 40.4 kcal per mole. A considerable amount of interest has been shown in recent years in the oxidation of tantalum and the nature of the oxide film produced. This interest is associated with the increasing demand in our technology for structural materials to withstand high temperatures and corrosive atmospheres. The low oxidation resistance of tantalum has severely restricted its application as a high-strength, high-temperature material. As a fundamental approach to the realization of the full poten- tials of this metal, the kinetics of the oxidation of tantalum in oxygen and air have been extensively studied; however, very little work has been reported on the effect of other gases, including carbon dioxide. According to Miller,' the only reported study of the reaction between tantalum and dry carbon dioxide is a restricted observation by O'Driscoll et al.2 at 8 atm absolute pressure and 500°C. Therefore, this study was made to investigate the reaction of tantalum with carbon dioxide. EXPERIMENTAL MATERIALS AND METHODS The vacuum-annealed tantalum used in this study was obtained from Fansteel Metallurgical Corp. as 0.025-mm-thick sheet stock. This material had less than 0.1 pct total impurities, and the maximum individual impurity concentrations were

Jan 1, 1964