Search Documents

amounted to about 2000 metric tons. The total output is increasing from year to year. Marine salt is now produced in Haiti in quantity sufficient to supply nearly all the requirements of this Republic, so production tax is now collected. Central America Guatemala-The major production of salt in Guatemala is solar salt derived from sea water, but the Indian population prefers salt derived by boiling coastal marine earth. Salt is taxed by the Government. The industry has been beset by controversies in recent years, especially following the revolution of October 1944. The Government issued a decree in August 1940 designed to control production and price of salt. The creation of a salt consortium was provided for and marketing was to be governed by production quotas. It is understood that the Government pool was later dissolved and the industry is now under older laws whereby production and sales have no limits. South America Panama-Output of salt in Panama in a very recent year was 11,000 net tons of solar-evaporated sea salt. A Government bank is in charge of output and distribution of the product. Colombia-Rock-salt deposits are known in five places-Zipaquira, Nemocon, and Sesquile, in the Department of Cundinamarca, the Cumural y Upin near Restrepo, and San Miguel y Barital, near Medina in Meta Intendency. The latter deposit never has been worked on account of its inaccessibility. Saline springs are worked in four locations. The largest producer among marine salinas is Manare but it is now planned to make Bahia Honda the largest. Some evaporated salt is made in vacuum pans. The deposits at Zipaquira, Nemocon, and Sesquile are believed to occur in the domal type of deposit. All the salt resources are under Government control. Venezuela-The salt industry in Venezuela is under Government control and is taxed. Taxes in recent years, however, have been reduced for salt used in curing hides and salting meats, fish and fish products. Production has approximated 25,000 metric tons yearly but may now be considerably above that figure. The basin on the peninsula of Araya, State of Sucre, which at present is the only important source of salt, could produce at least 175,000 metric tons if more ground were provided-a larger supply than the entire country could consume. This unique landlocked basin of nearly 1000 acres lies 12 ft below sea level. Ecuador-Salt is a Government monopoly in Ecuador and is produced chiefly by solar evaporation close to the shore. The main producing center is on the Santa Elena peninsula, which supplies about 90 pct of the salt. Small fields are at Punta Arenas, Payana, and Chara-

Jan 1, 1949

By J. Kent Smith

The object of this investigation was to ascertain the effect of varying percentages of beryllium upon pure copper and the properties of the resultant alloys in their softest condition, the effect of heat hardening on them, and the extents to which these properties could be augmented by different combinations of heat hardening and cold rolling. The data compiled in this paper represent partial results of continuing work done by the writer during the years 1930 and 1931, which was a continuation of the unpublished ground work incepted in the laboratory of the Beryllium Corporation of America by H. B. Pulsifer in the year 1926. A short bibliography on beryllium alloys is appended to this paper. It has, of course, long been known that copper subjected to cold work is hardened and strengthened to a considerable extent; furthermore it had been qualitatively noted in previous experiments that copper-beryllium alloys seemed to take on hardness and strength as the result of cold work at a greater rate even than does plain copper. It was decided therefore to endeavor quantitatively to determine such rate of increase, as also the relative increases by combinations of cold working and heat hardening. The results are summarized in Tables 3, 4 and 5. A preliminary series of experiments had indicated that by an exposure to the heat of 575" F. for 2 1/2 hr. age-hardening of a 2.50 per cent beryllium-copper alloy took place. Slab ingots of nine different beryllium-copper alloys were prepared under identical conditions by means of the addition of a previously prepared 12.5 per cent beryllium-copper alloy to well melted and deoxidized pure copper. The ingots were then reduced by hot rolling to 12 gage (about 0.080 in.). These strips were heated to 1450" F. and quenched in cold water, and thus brought to their softest condition. (See Table 1.) Strips were next "precipitation-hardened" by reheating to a definite temperature. Similar strips to those itemized in Table 1 (which had been quenched from 1450" F.) were reheated for varying periods of time at 575" F. The hardness figures show that a metastable condition, of which the range of stability is dependent entirely upon time at the given temperature, begins to be noted in copper samples containing as little as 0.85 per cent beryllium. It is extremely noticeable in samples containing

Jan 1, 1932

By M. Khorouzan, L. Thomas

Designers of semiconductor devices have been strivi,ng to resolve problems associated with Au-A1 alloys in bonded in.tercomzeclions. One approach now being- used is that of waintaining a physical seyav-atioz between the two metals in bond areas. This is accolrzplished by alunzincnz-plating a bonding area on the tips oJ the kovar leads and using alcminurn wires to join the senzicondictor device to the leads. The portion of the kovar lead which is on the externul side of the sealed package is gold-plated to provide an oxide-free surface for soldering or welding. A discoloration condition originally thought to be sinilar to purple plague, occuving in the yluled uluninur bonding area after package sealing, has been investigated to determine its efiects ipm bond integrity. Electron-micro-probe analysis determined that no1 only gold, but lead, zinc, and silicon were also present in the discolored area. A series of samples conlaining' conkrolled umonts of these inzpitrities weve prepared and subjected to a sil.zuluted sealing process. The investigations swcued that, of the contawiinants, only zinc toas detrinenlul to Lhe bond integily. The discoloration condition itself was found not to be detrimental to the bond integrity. DESIGNERS of semiconductor devices have been striving to resolve problems associated with Au-A1 alloys in bonded interconnections. One approach now being used is that of maintaining a physical separation between the two metals in bond areas. This is accomplished by aluminum plating a bonding area on the tips of the kovar leads and using aluminum wires to join the semiconductor device to the kovar leads. The portion of the kovar lead which is on the external side of the sealed package is gold-plated to provide an oxide-free surface for soldering or welding. Contamination as evidenced by discoloration of the aluminum-plated area was observed in a number of integrated circuits undergoing examination for defect characteristics which cause electrical failures.' This paper contains the results of an investigation to determine the nature of this discoloration, its cause, and its effect upon the integrity of the interconnection bond. I) THE NATURE AND EXTENT OF ALUMINUM-BOND CONTAMINATION The initial hypothesis in the investigation was that the discoloration was caused by reaction of the aluminum film with some unknown contaminants during the sealing of the hermetically sealed integrated-circuit flat package. The package is a rectangular ceramic container sealed with glass which surrounds the kovar leads as well as joining the top to the bottom. The seal is made hermetic by heating and cooling the package to devitrify the glass. In the case of the packages under investigation, the hermetic sealing had been accomplished with dry air as internal atmosphere. The apparent effect of contaminations as observed by microscopic examination was the formation of surface oxides having variations in color encompassing the whole spectrum of visible light. The contamination appeared to be related to one of the more notorious examples of these colorations, the so called purple plague.' In addition to purple plague, Fig. 1 shows the tarnish in the luster of the aluminized surface in the bond area which had been observed in many of the integrated circuits. To identify the contaminant in the bond area electron-probe microanalysis techniques were used.3 Fig. 2 shows the result of this analysis. The contaminants identified were gold, aluminum, zinc, lead, silicon, and cobalt. Fig. 2(a) is a back-scatter display of the area under study. The back-scattered electrons provide a general indication of the distribution of elements in the specimen surface. Elements with higher atomic number scatter more electrons back from the surface and are seen as light areas in the picture. The sample current, Fig. 2(b), is the amount of current conducted by the specimen as a result of electron-beam striking it and is an indication of element distribution. The Sample current is the reverse of back-scatter and complements it. Other pictures in Fig. 2 are produced by characteristic X-rays generated by the elements, allowing the isolation of the element of interest. The isolated element appears white and all other elements are dark. In this manner a comparative study provides a correlation between different surface areas and the elements which are in these areas. The area covered by the gold film, Fig. 2(c), shows that the boundary between the gold film and the kovar is not sharp as expected and that some sort of diffusion has taken place. Fig. 2(c) shows that some gold particles have been carried to the bond area and are in the proximity of the bonded wire in spite of the presence of a physical barrier in the form of the un-

Jan 1, 1967

By R. R. Nash, W. F. Sheely

Experiments were conducted on magnesium monocrystals in order to collect quantitative information on the mechanisms which limit the rate of basal slip. Using critical shear stress and creep data, activation energies for creep at low aid at high temperatures were derived. The activation energy at low temperatures is the same as that for jog formation and the activation energy at high temperatures agrees with that for climb. COTTRELL has suggested that at low temperatures, the expansion of dislocation loops under stresses near the yield strength is limited by the rate at____ which the expanding loops can cut the "forest" of dislocations passing through the glide planes.' On the basis of this mechanism, seeger2 has derived expressions for low-temperature creep and for the relation of flow stress of single crystals to temperature. In the work reported here, the authors have performed experiments designed to obtain quantitative data on the physical properties of the dislocation intersection mechanisms operating during basal slip in pure magnesium monocrystals. Above a critical temperature, dislocations thread-

Jan 1, 1961

By Ming-Kao Yen

A considerable amount of work has been reported in the literature in regard to the texture and earing behavior of copper strip. The rolling texture of copper has been confirmed as (110) [112] and (112) [111], which yields ears of a drawn cup at the position 45" from the rolling direction.1-3 The recrystallization texture has been established as the cubic or (100) [001] texture, where the earing positions are at 0" and 90" to the rolling direction.4-8 It has also been reported that in the development of cubically aligned grains of copper strips, the percentage of this cubic texture increased with an increase of final reduction and final annealing temperature.8,9 A comprehensive study on H.C. copper (British commercial copper of high-conductivity quality = Cu 99.95 pct, O2 0.03 pct, Ag 0.003 pct, Fe 0.005 pct and Pb < 0.001 pct) was made by Cook and Richards.6 They concluded that the recrystallization textures could be described as one or more of the following textures: (1) a single texture (100) 10011, (2) a twin texture (110) [112] and (3) a random orientation, depending upon the previous history of the specimen concerned. The effect of various alloying additions in copper was reported by Dahl and Pawlek.10 They found that certain alloying additions, such as 5 pct Zn, 1 pct Sn, 4 pct Al, 0.5 pct Be, 0.5 pct Cd, or 0.05 pct P suppressed the formation of cubic texture. Brick, Martin and Angierll reported that the cold rolled textures due to various additions fitted a rather simple pattern. However, the recrystallization textures were subject to very considerable variations. In the discussion of this paper, Baldwin stated that deoxidized copper containing 0.02 pct P gave a complicated recrystallization texture at lower temperature. When this copper was annealed at high temperature, a single texture appeared which was described as (110) [ill] but. according to a pri- vate communication from Baldwin, this orientation reported was in error and should have been reported as (110)[112]. He also reported that the earing positions of drawn cups were at 60" to the rolling direction.12 Recently, Howald, in his discussion on the paper by Hibbard and Yen,13 reported that the rolling texture of phosphorus deoxidized copper, containing from 0.006 to 0.020 pct phosphorus, was of the pure copper type. When these coppers were annealed at lower temperatures, they exhibited a random orientation, and when they were annealed at higher temperatures they had a mixed (111)[110] and (100)[001] texture, depending on the severity of the final reduction and annealing temperature. However, the specific influence of phosphorus and other impurities on the recrystallization textures and the deep drawing properties of copper strip has not been thoroughly reported. Therefore, an attempt has been made in the present work to determine the rolling and recrystallization textures and also the earing behavior of five types of commercial copper and thereby to evaluate the effect of phosphorus and some other significant impurities on the development of texture for cold reductions of about 87 to 89 pct. Materials Used The five types of copper employed in the present investigation were two phosphorus deoxidized coppers of different phosphorus content (0.007 and 0.013 pct P), an oxygen-free copper (OFHC), an electrolytic tough-pitch copper, and a fire-refined tough-pitch copper. These materials were subjected to a thorough spectroscopic and chemical analysis. The designations and the chemical compositions were as shown in Table 1. The coppers, FA1, FA2 and FA3. were hot-forged from 3-in. billets into a ½ X 6-in. plate and cold rolled to the ready-to-finish gauge indicated below. FA4 and FA5 were hot rolled and scalped to ready-to-finish gauge. The grain size of all the materials in the ready-to-finish condition was about 0.030 to 0.045 mm. Table 2 shows the last stage of the production schedule for each copper strip used. Experimental Procedure ANNEALING, GRAIN SIZE AND HARDNESS DETERMINATIONS Specimens of each type of copper were finally annealed in air for periods of one hour at temperatures ranging from 300 to 1600°F and were subsequently cooled in air. The average grain diameter of the annealed specimen was estimated by comparing with a standard grain size chart. Hardness was determined on the Rockwell 15 T scale. CUPPING TESTS Cups were made in a blanking and drawing set, in which blanks of 2-in. diam were drawn to a cup of 1.25-in. diam with an average depth of about 0.75 in. The clearance between the punch and die was about 0.032 in. The ears of the cup were measured with a special fixture which read the height of ears to one-thousandth of an inch on every ten-degree interval along the circumference of the cup. POLE FIGURES The usual transmission diffraction method with unfiltered copper radiation was employed to determine the pole-figures of the specimens cold-rolled or annealed at 900°F. All the pole-figures were derived from the positions of intensity maxima on 111 diffraction rings of the X ray photo-grams taken at 10 rotation of a

Jan 1, 1950

By E. P. Pfleider, D. H. Yardley

Layers of magnetic taconite of above average magnetic iron content extend down dip on the Mesabi Range to depths beyond the reach of open pit mining. A selected layer with thickness of 75 to 100 ft underlies many square miles. Such a selected layer can provide over 50 million tons of recoverable concentratc per square mile, at lower concentration ratios than in the present open pit taconite operations. The system contemplated would consist of large scale underground quarrying by a lane and pillar method. Working heights would be 60 to 100 ft; room widths, 50 to 75 ft; and productivity targets, about 40 tons per man-shift. The most critical problems would he roof control and blasthole drilling. The successful operation of large open pits and concentrating plants for treatment of magnetic taconites indicates that the basic techniques and economic problems of pellet production have been solved. The open pit reserves are large, but they are not necessarily available in sufficient quantity or quality to provide an adequate raw materials base for all potential producers. Furthermore, as the more easily available open pit crudes are used up, the pits will become deeper, stripping costs per ton of concentrate will increase, and recoveries will decrease as leaner crudes are utilized. The time will come when supplementary and replacement reserves of magnetic taconite will be required. One way these can be obtained is by underground mining of the down-dip extension of the Mesabi magnetic taconites, especially those layers averaging well over 25% recoverable iron. A key point in such a proposal is the possibility of realizing substantial savings by beneficiating an ore of 30% magnetic iron at 2.5 to 1 ratio of concentration. This contrasts with current practice in Mesabi commercial taconite plants, where the ore averages 22 to 25% magnetic Fe, with concentration ratios of about 3.0 when producing 61% Fe pellets. Two factors which favor the eventual development of underground taconite mining are: 1) the desirable physical structure and high grade of taconite pellets in general and 2) the improved engineering techniques in underground mining. Experience in large scale room and pillar mines demonstrates that, given strong rock strata immediately above a high grade mining

Jan 1, 1963

By George Rice

THE subject of dust explosions in coal mines first appears in the Transactions of this Institute following the first great mine disaster that happened in bituminous mines of the United States. This was the Pocahontas explosion, which occurred Mar. 13, 1884, causing the loss of 112 men. The operating company wisely asked the technical assistance of the Institute, requesting that a committee be appointed to investigate and report. This committee consisted of Messrs. Bramwell, Buck, and Williams, who, after careful study, reached the conclusion that the explosion was due "either to dust alone or to dust quickened by an admixture of fire-clamp too slight for detection by ordinary means." This is perhaps the first time in this country that coal dust was considered to be the chief agency in a mine explosion.. The report is given in the Transactions, vol. xiii, p. 237 (1885). It is particularly worthy of note that the committee called attention to "the necessity of full-sized tests and systematic experiments. " In the same volume of the Transactions, there is a most interesting paper reviewing the literature relating to coal dust, by E. S. Hutchinson, entitled Notes on Coal-Dust in Colliery Explosions. Mr. Hutchinson gives a historical account of observations on the part played by coal dust in mine explosions, beginning with Messrs. Lyell and Faraday&apos;s report on the Haswell colliery explosion in 1844, in which it is said "much coal gas had been made from this dust in the very air itself in the mine by the flame of the firedamp, which raised and swept it along, and much of the carbon of the dust remained unburned only from want of air." The subject lay dormant until 1875 when William Galloway began some coal-dust experiments in a small gallery at a mine in South Wales of which he was manager. At that time he considered the presence of firedamp necessary for continued propagation of a dust explosion; but in 1884, the year of the Pocahontas disaster, he stated that no earlier author-than himself had credited coal dust with being a principal factor in mine explosions, relegating firedamp to a secondary place.

Jan 10, 1914

By R. Hogg

Sintering is a process in which the pore structure of an agglomerated powder is modified. For many applications, it is desirable to be able to control the pore structure in order to optimize such properties as mechanical strength and reactivity (availability and accessibility of solid surfaces to reactant gases, for example). In general, these properties will be determined by the total porosity and the pore size distribution of the agglomerate. In the work described in this paper, a physically realistic mathematical model for the sintering process has been developed. The model is based on the usual assumption that the pore system in an agglomerate can be treated as a network of interconnecting, cylindrical pores of continuously varying size. It is further assumed that the total pore length is conserved during the course of the sintering process. Using standard expressions for the rate of shrinkage of an individual pore, the model can be used to predict the changes in total porosity and pore size distribution as sintering proceeds. Experimental pore size distributions, obtained by mercury intrusion porosimetry, for the sintering of oxides appear to be in general agreement with the predictions of the model.

Jan 1, 1977

By B. H. Caudle, L. H. Silberberg

Reservoir depletion by natural water drive is typified by the movement of water from an aquifer into the adjacent oil-bearing formation. Prior studies of this type 01 water movement have generally neglected the resistance to flow in the aquifer and its effect on the movement of water into the oil bearing zone. A method for designing and operating scaled models of such reservoir systems is presented. Experimental data on a model of an edge-water-drive reservoir are shown and discussed. INTRODUCTION Most petroleum reservoirs derive at least a part of their productive capacity from water influx. This water may be injected from the surface or it may come from an aquifer adjacent to the oil zone. In either case, the reservoir engineer must be able to estimate the advance of the water as a function of either the elapsed time or the fluid produced. This paper describes a type of fluid flow model which includes the effect of viscous and gravitational forces in the reservoir and the surrounding aquifer. Natural water influx can be divided into three general (but widely overlapping) categories according to the direction of flow in the aquifer. These are shown schematically in Fig. 1. Fig. l(a) illustrates an edge-water-drive mechanism. In this case, water advances updip along the stratum but the movement of water is essentially horizontal and very little of the oil is actually underlain by water. The bottom-water drive (Fig. l(b)) is characterized by a thick aquifer underlying the oil zone. The water movement is generally vertical in the aquifer. The third category is illustrated in l(c). Referred to as the "thin oil column", this type of oil accumulation consists of oil over water in a relatively thin stratum. Fluid movement is horizontal in both the oil and water zones, except close to the producing well. One characteristic which all three of these types have in common is that part of the water flow takes place in the water invaded region of the oil reservoir while the remainder of the water flow occurs in the aquifer. The resistance to the flow of water usually will not be the same in these two regions. This occurs because the porous rock normally contains only water in the aquifer, while the water-invaded region always contains microscopic globules of bypassed oil (residual oil) which interfere with the flow of water through the rock. The production history of any type of a water-drive system is a function of two phenomena — where the water goes, and how it displaces the oil in the area invaded by the water. It is usually impractical to study these two phenomena at the same time. In most cases one type of analysis is used to predict the gross movement of water in the reservoir, while a different type of analysis is employed to determine the amount of oil to be recovered from the gross volume contacted by the water. The portion of the oil reservoir which is invaded by water is mainly a function of the resistances to fluid flow in the several parts of the flow system. This gross water influx in the three types of natural water drive typically results in water cusping to the production wells either from the side or from below (water coning). In 1747, Muskat described a greatly simplified mathematical model for predicting the area invaded by water in a bottom-water-drive reservoir.1 This model used the Laplace equation and suitable boundary conditions to describe the isopotentials and streamlines in the flow system. The use of this model assumes that (1) the reservoir rock is homogeneous in nature, (2) the oil and water mobilities are equal, (3) there is no oil flowing in the water invaded region, and (4) external forces — such as gravity — do not affect the flow. This method has been used for both natural water drives and water injection projects. In this, as in most models, the method of images is used to reduce the size of the model necessary to describe the reservoir. The assumption of equal viscosities and permea-

Jan 1, 1966

By J. Lyndon Rosenblad

This chapter describes the development of a rocklike model material for use in tests with a rock-blocks model to investigate the failure mechanism of a discontinuum. In order to provide reliable results, the model material must be characteristic of natural rock and obey the laws of similitude. Initially, the development of such a material does not appear to be a difficult problem. Only when one undertakes such a task does he realize how little is actually known, and that there is considerable work yet to be done. A material that simulates rock in all of its physical properties probably will never be developed. There is now and probably always will be room for improvement. Improvement is needed not only in the component materials but also in the technique of preparation. The material developed and subsequently described in this chapter simulates rock in general and a schistose gneiss rock in particular. The material possesses many rocklike physical properties not found in previously used model materials. One of the most significant improvements of this material is that there is an increase of Young&apos;s modulus with an increase in confining pressure as determined by triaxial compression tests. A change in the usual procedure of material preparation was used to develop this material and is also described. MODEL MATERIALS USED IN THE PAST Intact Materials Numerous materials have been used by investigators in models in the past to simulate a wide range of prototype materials. Some of the materials used include cork, plastic, concrete, plaster of Paris, portland

Jan 1, 1972

By K. Brack, G. H. Schwuttke

Annealing properties of subszerface amorphous lavers produced through high-energy ion implantation in silicon are studied. The buried layers are produced through the implantation of ions (nitrogen), ranging in energy from 1.5 to 2 mev. X-ray interference patterns, transmission electron microscopy, and resistivity profiling are used to study the annealing characteristics of the ion damage. The annealing experiments indicate a low temperature (below 700°C) and a high temperature (above 700°C) region. Significant changes occur in the amorphous layer during the high-temperature anneal. Such changes are corre-lated with the re crystallization of the amorphous silicon and the formation of subsurface (buried) silicon-nitride films. TODAY&apos;S main problems in the field of ion implantation are related to the accurate determination and prediction of 1) the distribution profiles of implanted ions, 2) the lattice sites occupied by the implanted ions, 3) the lattice damage produced through ion implantation, and 4) the annealing characteristics of damage centers in the lattice. This paper reports investigations concerned with the problems listed under 3) and 4). EXPERIMENTAL Our investigations cover the energy range of incident ions from 100 to 300 mev and from 1 to 2.5 mev. The emphasis of this study is on the energy range from 1.5 to 2 mev. The experiments are conducted with single charged nitrogen ions. To implant the ions a van de Graaff generator is used as described by Roosild et al.1 Accordingly, a gas containing the desired ion specie is passed through a thermome-chanical leak into a radio frequency activated source. The positive ions are driven into the van de Graaff with the help of a variable voltage probe. Emerging from the accelerator the ions drift into a magnetic analyzing system and here the desired ion specie is bent 90 deg into the exit port. The ion beam leaving the analyzer is defocused and drifts down a 4-ft long tube to hit the silicon target. At this position the 20 pamp ion beam has a circular cross-section of 2.1 cm. N2 is used as a source gas for nitrogen ions. The implantation target is silicon with zero dislocation density, 2 ohm-cm resistivity, (111) orientation, mechanically-chemically polished, and 1 mm thick. The target is mounted on a water-cooled heat sink and kept at room temperature. A fluence of 1015 to 1016 ions per sq cm is used. RESULTS 1) Silicon Perfection after Bombardment. High-energy ion bombardment of silicon has some striking effects on lattice perfection. Some results were reported in detail previously at the Santa Fe conference2 and are here briefly summarized for the benefit of the experiments described in the following. 1.1) Identification of Surface Films on Silicon. After bombardment all samples are found to be coated with surface films. The films on the silicon surface vary in thickness and color; they can be transparent, slightly brown, or opaque. The films are thicker and darker in the high-intensity area of the beam and they delineate the bombarded surface area of the crystal. The films produce electron diffraction patterns characteristic of carbon and of SiO2. Carbon is predominant. The presence of carbon in these films was confirmed by use of the electron microprobe. Formation of the films occurs independently of the ions used and is attributed to a contaminated vacuum of the high-voltage machine. The carbon is most likely the product of the pump oil which is cracked and polymerized under ion impact. The films stick tenaciously to the silicon surface and burn off in a low-temperature Bunsen flame. 1.2) Mechanical Perfection of the Silicon Surface. The mechanical perfection of the bombarded silicon surface was investigated through optical microscopy, electron microscopy in which the replica technique is used, and optical interferometry. No mechanical damage of the surface was visible after bombardment. However, if a bombarded sample is soaked for several minutes in hydrofluoric acid (HF), gas bubbles may develop in certain spots of the silicon surface. It is also noted that in these areas the surface film starts to peel off. Relatively large patches of film come off if the sample is soaked in HF during ultrasonic agitation. After HF treatment, pits may be present on the silicon surface. The pit dimensions are estimated to be as large as 50 µ. The pits appear in the region of most intense irradiation. 1.3) Lattice Perfection After Bombardment. No lattice damage is found on the silicon surface. Electron transmission micrographs and selected area diffraction patterns of the surface show no difference before and after bombardment. Measured approximately 2 µm down from the surface, the silicon lattice throughout this depth is of good perfection. Well-defined Laue spots and Kikuchi lines are obtained from the surface as well as from the indicated area below the surface. However, some radiation damage is dispersed in this top layer. A sharp boundary line separates this surface layer from a highly damaged layer which extends further downward into the silicon. Typical of this

Jan 1, 1970

By A. M. Talbot, John T. Norton

TheRe is still considerable controversy as to the exact nature of the mechanism of the age-hardening process, in spite of the many experiments already performed. For this reason, a considerable number of typical systems should be examined in detail and their results correlated. Furthermore, the methods of studying the changes that take place during the progress of this phenomenon should be carefully scrutinized and the different methods applied to the same samples, preferably at the same time. The experiments described in this paper are presented to supply information on one age-hardening system and to show how the various methods of investigation compare in their indication of what has happened. In brief, the progress of aging in magnesium alloys containing about 10 per cent by weight of aluminum at different temperatures was followed by measurements of hardness, electrical resistivity, dilation and lattice parameter, and by microscopic observation. Previous Work Meissnerl,$ Archer?, and Gann3 have investigated the changes in mechanical properties of magnesium-aluminum alloys during aging and have shown the optimum condition for the age-hardening treatment. Meissner&apos;s results are particularly interesting because when replotted so that they represent hardness as a function of aging time, the curves of 125" and 150" C. show two hardness peaks. This result was not confirmed in the present work. Schmid and Siebe14 have reported an investigation that is similar to the present one but it was not published until the present work had

Jan 1, 1936

By M. L. Pearce

A comparison of the isotope-dilution, vacuum-fusion, and chemical methods of analysis for nitrogen in Si-Fe is made with particular emphasis on the effect of sample history. The superiority of the isotope-dilution method from the point of view of 1 HE analytical techniques used to determine nitrogen in Si-Fe have been subjected to close scrutiny in recent years primarily because of the marked influence of the element on the properties of the alloy. These investigations have led to a diversity of opin- both precision and accuracy is demonstrated. The solubility of nitrogen in 3.06 pct Si-Fe is investigated and the effect of silicon content on the activity coefficient of nitrogen is derived. ion regarding the reliability of the vacuum-fusion and chemical methods of nitrogen analysis when applied to si- Fe.&apos;-&apos; A majority of workers appear to favor the vacuum-fusion method over chemical methods particularly in those cases where part of the nitrogen may exist as silicon nitride or the total nitrogen content is very low. Contrary views have been expressed, however,&apos; and it has been demonstrated that for some Si-Fe alloys both methods yield results which are significantly lower than those

Jan 1, 1963

By G. Bjorling

The opening oxidation of a hydrometallurgical treatment of natural sulphides must for several reasons be so controlled that a maximum of the sulphide sulphur is transformed into elemental. If the oxidation is performed at low pressure and moderate temperatures and with mild reagents such as diluted nitric acid (or ferric or cupric chloride) the just mentioned condition is realized and it has been found possible to conduct the reaction so that solutions are obtained from which the metals can be recovered and the reagents required for the dissolution are regenerated. Experiments in laboratory scale with nitric-acid promoted oxidation have shown that this method is applicable to several types of raw materials, and in combination with electrodialysis both for partial neutralization and for final regeneration of the circulating acid can the requirements of low consumption of chemical reagents and formation of harmless residues be well fulfilled. The metals can be recovered as cathodic deposits or as hydroxides, and the method should be applicable also for low grade ores and concentrates. Although oxidation of sulphides by ferric or cupric ions has the advantage that it can be performed in open vessels it seems well worth the complication of working with nitric acid promotion in a low-pressure autoclave. Also complex sulphidic, oxidic and metallic materials can be treated.

Jan 1, 1973

By John M. Dealy, Robert D. Pehlke

Values for interaction parameters in nonferrous systems, as calculated from published data, are tabulated and discussed. The influence of temperature on the parameter is derived and compared with the results of the literature study. Wagner&apos;s relationship between the interaction parameter and the self interaction coefficients is compared with the tabulated data. A problem which has been of considerable interest in the field of metallurgy is the prediction of the effect of one alloying element present in dilute concentration on the thermodynamic properties of another dilute alloying element. Ultimately, the prediction may be accomplished entirely from statistical mechanical considerations. At the present, however, the problem remains unsolved since liquid solution models which are simple enough for analytical treatment are inadequate for such purposes. Thus, we desire some means of organizing the information on dilute systems which will serve as a guide for further study on interactions in dilute alloys, and also provide a basis for the utilization of thermodynamic data in the engineering design of alloys.

Jan 1, 1963

By Wilbur Nelson

THE year 1923 has been a dull period in oil development in Kentucky and Tennessee, with the exception of the Kettle Creek area along the Tennessee-Kentucky line, in Clinton and Cumberland Counties, Kentucky, and Clay County, Tennessee. The price of oil during the year has been so low that wildcatters have shown little interest in drilling. At the beginning of the year, light oil sold for $2.31 per barrel and medium oil for $2.06 per barrel. Prices increased to the highest point for the year in February, when light oil brought $2.86 per barrel and medium oil, $2.61. In April, prices had declined 35 c. while in May an additional decline of 25 c. went into effect. During June, prices declined 20 c. per barrel; during July, 45 c. per barrel; remained stationary during August and September, and dropped during November and December to the low price of $1.36 per barrel for light and $1.21 for medium oil. At present, an increase of 29 c. has brought the price of light oil up to $1.55, and indications are that the price will continue to increase during the coming months. It can readily be seen that during 1923 the price of oil was such as to prevent any drilling except that necessary to hold leases and to maintain production enough to take care of overhead expenses.

Jan 3, 1924

By M. K. Barnett

[ ] ENGINEERING research consists, broadly speaking, in the investigation of the effect of the variations in a number of factors on some property of a product or characteristic of a process. The unambiguous description of the product or process requires that the property or characteristic be expressible in quantitative terms. For the purpose of practical control, it is likewise desirable that the independently variable factors governing the product or process be quantities, although this ideal goal is not always attained. Maximum efficiency-i.e., the attainment of the maximum amount of reliable, useful information relating to the influence of the factors on the property of the product or characteristic of the process, for the least expense-is an important requirement for the satisfactory operation of a research organization. Obviously, a necessary condition for the attainment of maximum efficiency is an adequate knowledge of the specialized field in which the experimental research lies. While necessary, this condition is not sufficient. Proper attention must also be given to the general principles of experimental design together with the modem methods for the analysis and evaluation of experimental data. The present discussion is confined to a single design, the so-called "factorial" design. This design is of special interest in that it attains its goal, maximum efficiency, by directly departing from the

Jan 1, 1947

By Henry F. Cooper, Lee Burford, John C. Thompson

In the past year or two, considerable effort has been expended to calculate the spherical wave propagation phenomena associated with explosions in a "hard rock" medium (Godfrey, 1969; McKay and Godfrey, 1969; Burford, et al, 1970). This effort was stimulated primarily by the recognition that early calculations predicted peak particle displacements which seriouly disagreed with field data. In most of the calculations mentioned above, rock was modeled as an inelastic continuum (see for example Isenberg, et al, 1970 for some recent results using "classical" elastic-plastic material property models). However, several investigators (Handin, et al, 1967; Cherry, et al, 1967) have shown that the simple classical yield surface models cannot simultaneously account for the observed brittle failures of intact materials under compression, extension and torsion. One approach to more correct modeling of dynamic rock behavior is to make the inelastic model more and more sophisticated. For ex- ample, recent experiments at the University of Utah (Swanson, 1969) have suggested possible modifications to the yield surface model that could better account for the ductile behavior of intact granite sam- ples under various states of stress. The approach followed in this paper proceeds in an entirely different direction. We want the physics which is built into our conception of rock to be as simple as possible while at the same time reproducing the most important features of rock&apos;s behavior. Therefore, we abandon the requirement that rock be treated strictly as a continuum. Instead we consider a "discontinuous" model in which one of the most significant characteristics of rock is treated..

Jan 1, 1971

By E. F. Steeb, P. C. Rosenthal

BlANKS 8 in. long were cut from the as-received bar stock and austenitized at 1560° F for 1 hr, oil quenched, tempered at 1140°F for 1 hr, and water quenched. The heat-treated blanks were machined into tensile specimens which were subsequently used for the straining operation. Some of the tensile specimens were temper embrittled at 900°F for 24 hr and air cooled prior to or following the straining operation. The specimens were strained in tension up to 5 pct total strain (elastic plus plastic) either at room temperature or at 900°F. The reduced sec- tion of the tensile specimen employed was 5 in. long and 0.600 in. in diam. This size specimen was sufficiently large to permit two standard Charpy impact bars to be machined from it. One group of specimens was temper embrittled at 900°F for 24 hr under stress of about 20,000 psi applied with a hydraulic tensile testing machine. Approximately 0.34 pct plastic strain occurred during this treatment. A comparison of series "A" and "B" data in Table I at 0 pct strain, reveals that the steel was rather highly susceptible to temper embrittlement, the embrittling treatment causing the transition temperature to rise 165°F. The 28 ft-lb level, which was near the center of the sharp-rising portion of the transition curve, was selected as the

Jan 1, 1959

By Cyril Stanley Smith

METALLURGISTS - or at least metals - have been of central importance in most of the inventions that have shaped the course of man&apos;s history. From the first Bronze Age tools to the iron armor of the Roman soldier, the cannon, cast type for printing, the steam engine, the electric motor and modern electronic devices, technological progress has revolved around some particular property or comb nation of properties selected from the metallurgist&apos;s repertory. The recent utilization of the energy of the atomic nucleus (currently for military purposes alone but with great constructive implications for the future) is no exception to this, although the use of uranium and plutonium in metallic form is of secondary importance, since the significant properties are those of the nucleus and not of the electrons responsible for metallic behavior. THE METALLURGIST AND ATOMIC ENERGY The metallurgist has a role of central importance to play in the future development of atomic energy. Not only must he make and shape the fissionable materials themselves, but he must also develop auxiliary materials to withstand the extreme conditions imposed on nuclear reactor components by the high heat-transfer rates needed for efficient utilization of the fuel and by the perplexing but interesting effects of radiation on the structure and properties of materials. It is doubtful if there is currently any other field potentially more rewarding to a young metallurgist. Quite apart from the all important but relatively short-range considerations of national security is the vision of the effect on civiliza-

Jan 1, 1953