Search Documents

By J. Phillip Neal, Kefton H. Teague, Carroll P. Rogers

Feldspars, the most abundant minerals of the igneous rocks, occur in numerous forms and mixtures. The feldspars of commercial significance are found in widely distributed pegmatites as large crystals usually free of iron-bearing impurities and thus suitable for hand-cobbing, and also in larger bodies where the ore contains various types of feldspar intermingled with quartz and relatively free of iron-bearing impurities, or at least readily unlocked from impurities present at relatively coarse mesh. The latter type of ore includes some pegmatites, and the "alaskite" bodies so common in the Spruce Pine district of North Carolina. On the west coast of the US and in Oklahoma there is-or has been-commercial recovery of natural feldspathic sand as a source of alumina in glass and ceramics. "Aplite" in commercial terminology is a light-colored igneous rock with a granitic composition and a fine sugary texture, often banded with readily removable iron impurities. Only one area in Virginia produces aplite for the glass industry; it is located near Montpelier in Hanover County. According to Deer et al. (1966) the word feldspar derives from the Swedish feldt or jolt (field) and "spath:" chunks of rock appearing in tilled ground overlying granite. Castle and Gillson (1960) indicate a Germanic origin, citing "spat," which is said to refer to any transparent or translucent material which is readily cleavable. The term "spar" has in the past been applied to minerals other than feldspar, such as barite, calcite, and fluorite. It is correct to call the latter "fluorspar." There is a true barium feldspar, but it is rare and of no present economic importance. What is recognized as feldspar or "spar" by present producers and consumers consists of three silicate minerals which, if pure, would have the formulas KA1Si3O8 (microcline or orthoclase), NaAlSi3O8 (albite), and CaAl2Si2O8 (anorthite). These are almost never found in pure form in nature, but occur together in great abundance in a three-component system. A considerable number of different combined ratios of these three exists, with the exception that isomorphism between potassium spar and calcium spar is very limited. User specifications for feldspar products are largely built around the prevalent naturally occurring ratios. Passages following will refer to "K-spar," "Naspar," or "Ca-spar." Nomenclature and Descriptive Terms Relating to both the mineralogy and the economics of feldspar are certain terms whose coverage it is useful to specify. Commercially, aplite is a feldspathic rock mined and beneficiated in one location in Virginia, in which both titanium and feldspar minerals are present-the latter now being the major, if not the only, economic product. Technically, the term aplite when applied to this rock is of questionable accuracy. But, in light of accepted commercial usage, the term will be here used to designate it. Regarding the Virginia rock, Ross (1941) is cited. Alaskite is another term requiring understanding if not precise use. A distinctive rock type customarily called by this name is found near Spruce Pine, Mitchell County, North Carolina. An important major feldspar source, it contains somewhat higher levels of plagioclase feldspar and quartz than alaskite as defined in the Glossary of Geology and Related Sciences, which states that `orthoclase, microcline, and subordinate quartz are the principal

Jan 1, 1983

By E. O. Wagner, V. F. Parry, J. B. Goodman

The low-rank coals containing 10 to 50 pct natural bed moisture represent over half of the tonnage reserve of the available solid fuels of the United States, but only about 2 pct of United States coal production is derived from these fuels. Increased utilization of these large reserves will result if the bed moisture can be removed at the mine in high-speed low-cost processes. This paper presents a theoretical and experimental study of the factors affecting high-speed drying of coal dusts. The time required to heat particles of coal is proportional to the square of their diameter, and it is calculated that the probable time in minutes is equal to 6D2. In other words, a 1/16 in. coal particle should be heated to drying temperature in 1.5 to 2.0 sec. Likewise, 1/8 in. particles should be heated in about 6 sec. The net heat required to dry subbituminous coal and lignite varies from 240 to 375 Btu per pound, depending upon the moisture removed, and this heat can be obtained from 42 to 61 cu ft of hot gases at 600°F. The necessary heat also can be obtained from 7.5 to 11 cu ft of gas at 2000°F. A description of the design and operation of a pilot plant for flash drying coal dusts is presented. This plant dries 1/16 in. by 0 coal dust in suspension in 1.5 to 2 sec with 600°F gas at a rate of 1300 lb per hour per square foot of column area and operates continuously at an efficiency of about 85 pct. The design and operation of another pilot plant for drying 1/8 in. by 0 coal dusts Is also described. This unit dries coal in the fluidized state using the sensible heat of gases introduced at 2000°F and processes coal at a rate of about 1500 Ib per hour per square foot of grate area at 85 to 90 pct efficiency. Over 90 pct of the bed moisture of low-rank coal dusts can be removed by the methods described. The heating value of lignite can be increased 45 pet and that if subbituminous coal 25 pct in a few seconds. The physical and chemical properties of coal dusts before and after drying are presented in the report, and it is shown that the bulk density of the dried coal is equal to that of the raw coal. This phenomenon makes it possible to ship 25 to 45 pct more heat in a railroad car with consequent savings in freight costs. Introduction For several years the Subbituminous Coal and Lignite Section of the Coal Branch of the Bureau of Mines at Golden, Colo., has been concerned with upgrading low-rank coals by removal of natural bed moisture. These fuels contain 10 to 50 pct total moisture, which reduces their industrial value considerably. In 1938, investigations were initiated in cooperation with the University of North Dakota to study drying of lignite by the Fleissner process with heat derived from high-pressure saturated steam. Two pilot plants were built, and two reports were published giving the results of this work.l,2 It was demonstrated that lump lignite and subbituminous coal

Jan 1, 1950

By James R. Dunn

The purpose of this chapter is to review the uses of sand and gravel by the construction industry. The specific intention is to give tech¬nical people the general perspective and frame¬work which they need to help in making tech¬nical and business decisions. In the sand and gravel industry such decisions are based on an understanding of sociologic, economic, and technologic factors. In order to discuss the sand and gravel industry intelligently, it is necessary to define sand and gravel. "Sand" as most often used by industry is not sand in an engineering or geo¬logic sense but should be called "natural fine aggregate." The expression "fine aggregate" is preferable to "sand" because fine aggregate in¬cludes grain sizes which, according to engineer¬ing or geologic classifications, are defined as pebble or grit size. Natural fine aggregate is distinguished from manufactured fine aggregate in that the manufactured material is crushed and screened to produce the required sizes and natural fine aggregate is only screened. Coarse aggregate is generally defined as aggregate which will not pass a No. 4 or %o-in. sieve. Coarse aggregate may be natural (gravel) or manufactured (crushed stone, crushed gravel, slag, or coarse lightweight aggregate). Gravel is usually considered sufficiently crushed to qualify as manufactured coarse aggregate when two or more sides are broken. Sand and gravel (crushed or uncrushed) is used in asphaltic and portland cement concretes, is subbase for pavements, as fill where good drainage is needed (such as around structures), and for many other uses. About 96% of all he sand and gravel produced is used in construction.

Jan 1, 1975

By B. H. Cody

The Morenci concentrator of the Phelps Dodge Corporation is a part of the project that was completed after five years had been spent in development of the open-pit mine, equipment and process testing in the former No. 6 concentrator, and construction of the reduction works. The reduction works, of which the concentrator is a part, is about a mile and a quarter southeast of Morenci, on the highway that leads up Morenci Canyon. The concentrator has a nominal capacity for the treatment of 45,000 tons of ore daily. The original plant, which has a rated capacity of 25,000 tons of ore daily and is now in its fifth year of operation, began production on Jan. 30, 1942. The addition, to increase the capacity 80 pct, began operation on Dec. I, 1943. The equipment of the original plant has been described in Mining and Metallurgy (May 1942). NO changes in equipment were recommended for installation in the concentrator extension and only one major change, forced by a shortage of maintenance labor, has since been made. Metallurgical treatment has been altered in some ways as experiments progressed and as labor and economic conditions dictated. No complete description of the operation of the concentrator has been published, so this paper will record such operating and equipment changes as have been necessary, the operating methods that have been developed and the metallurgical results that have been obtained. Descriptions are given in the order of the processes with a flowsheet and an equipment list of each process for convenient reference. The questions asked by engineer visitors have guided the detail in which operation and maintenance are described. During the period Jan. 30, 1942 to Sept. I, 1946, ore milled has totaled 43,595,253 dry tons, from which 1,643,885 tons of concentrate have been made, containing an indicated production of 783,164,-809 lb of copper. The principal results obtained in operation of the concentrator during the years 1942 to 1945, inclusive, and to Sept. I, 1946 are shown in Table I. A graphic general flowsheet of the plant is given in Fig I. Ore The Morenci ore that is now being treated is a medium-hard monzonite porphyry in which the principal sulphide minerals are chalcocite and pyrite. A minor amount of covellite is present. Chalcopyrite and bornite have been observed under the microscope. The chalcocite occurs mainly as a coating on pyrite. Some of the coatings are so thick that the pyrite presents the appearance of being an inclusion in chalcocite. Some are less than one micron thick and are barely visible at 500 diameters magnification of a polished cross section. Some chalcocite is present as a in in the gangue. Various oxidized copper minerals are present as a result of oxidation in place but they represent a minor proportion of the copper minerals of the ore body. Oxidation

Jan 1, 1949

By P. Gordon

An isothermal jacket microcalorimeter, supplemented by metallographic, microhardness, and X-ray measurements has been used to study the isothermal annealing of high purity copper after room temperature tensile deformation. The amount of stored energy released during annealing has been measured as a function of deformation in the range 10.8 to 39.5 pct elongation. The data have shown the major heat effect to be associated with recrystallization and have allowed an analysis of the recrystal-lization kinetics and the calculation of activation energies of recrystallization. WHEN a metal is deformed plastically, some of the energy expended is dissipated as heat during the working process, while the remainder is stored within the metal in the form of lattice distortions and imperfections. During subsequent heating of the metal, the distortions and imperfections can be largely annealed out and the associated stored energy released as heat. It is apparent that measurements of the evolution of stored energy during such annealing may produce important information concerning the nature of the annealing mechanisms and the imperfections involved. Some excellent studies of this type have been made in the past, notably those of Taylor and Quinney,' Suzuki,2 Bever and Ticknor,3 Borelius, Berglund, and Sjöberg,4 and Clarebrough et al.5,6 None of this work, however, employed isothermal techniques, with the exception of the Borelius studies' in which only the early annealing stages were investigated. Since isothermal measurements, as compared with heating or cooling curve, have the merits that 1—they reveal the kinetics of a process more clearly, 2—the results obtained are more easily applied to theory, and 3—most fundamental investigations of annealing using techniques other than calorimetry have been carried out isothermally, it was considered important to apply calorimetry to the study of the isothermal annealing of metals. Accordingly, an isothermal jacket calorimeter of the Borelius type,' supplemented by metallographic, hardness, and X-ray measurements, has been used to study the annealing of high purity copper after room temperature tensile deformation. Experimental The microcalorimeter has been described fully elsewhere." Briefly, the specimen to be studied is placed in a constant temperature environment of virtually infinite heat capacity achieved, as shown in the drawing of Fig. 1, by means of a vapor thermostat. A high thermal resistance is provided between the sample and the environment and a sensitive differential thermopile (see Figs. 2 and 3) arranged with half its junctions in contact with, and thus at the constant temperature of, the environment, and the other half in contact with the sample. A reaction in the sample develops a small difference in temperature, AT, across the thermopile, which is followed by a recorder-galvanometer set-up as a function of time, t, and is converted to reaction heat per unit time, P, by the use of the equation AT P=a?T + b AT dt The constants, a and b, in Eq. 1 are determined by a simple calibration, making use of the Peltier heat developed by a small current run through the junction of a thermocouple located in an axial hole in the specimen (Fig. 2). In its present form, the limit of sensitivity of the calorimeter is a heat flow of 0.003 cal per hr. The copper used was the spectroscopically pure metal supplied by the American Smelting and Refining Co. in the form of 3/8 in. diam continuously cast rod, reported to be 99.999+ pct Cu. A small amount of the copper was available at the start of this work and is referred to hereafter as lot A. A second batch, lot B, was obtained later, most of the results described subsequently being for this lot. As will be seen, there is some indication that lot A was somewhat purer than lot B, but it is not known whether this difference was present in the as-received metal or arose during subsequent handling. The two lots of copper were remelted and cast into two 1½ in. diam ingots in vacuo, using high purity graphite crucibles and molds. The ingots were upset several times to break up the large cast grains, and then rolled and swaged to rods 0.391 in. in diameter, using several intermediate anneals with about 40 pct reduction in area between anneals. The penultimate anneal was 2 hr at 350°C. X-ray examination showed no marked general preferred orientation in the resulting rods. The grain structure typical of the two rods is shown in the micrograph of Fig. 4." It was found to be virtually im- possible to get an unambiguous measure of the absolute grain size in the two annealed rods because of the profusion of annealing twins and the lack of regularity of the grain boundaries. However, counts of the number of boundaries intersected per unit length along a random line on a polished section, making a correction for the proportion of boundaries (about half) estimated to be twin boundaries, gave a figure of about 0.015 mm for the average grain diameter. The grain size of the rod from lot A was about 5 pct smaller than that from lot B. The rods were cut into 1 ft long bars and these deformed in tension at room temperature to various total elongations in the range 10.8 to 39.5 pct. A strain rate of 1 pct per min was used. The deformed bars were then stored in a dry ice chest until such time as samples were to be cut from them. Five bars deformed as indicated in Table I were used for the subsequent tests. In all cases, all the calorimeter.

Jan 1, 1956

By Michel Elle, John Chipman

The equilibrium of gaseous H20-H2 mixtures with liquid iron-columbium alloys in the range 0.2 to 2.4 pct Cb shows that the activity coefficient of oxygen is strongly diminished by Cb. The oxide in equilibvium with the melt is identified as CbO2. The equi-librium constant at 1600 deg C is [%Cb][fo. % 0]2 = 2.9 x 10-4 where log fo= —0.14 [%Cb]. The deoxidizing power is comparable to that of vanadium, COLUMBIUM (niobium) is finding increasing use as an alloying element in steel. It forms several stable oxides and is removed from the steel bath by oxidizing slags. The specific oxide formed in steel-making is not known although Sazanov snd Shvarts-man,' in their study of its partition between slag and metal, have assumed this to be Cb2O5 It is the purpose of this study to determine its deoxidation equilibrium at 1600°c, the nature of the oxide formed and the interaction between columbium and oxygen in the melt. The investigation was based on the reaction H2 + O=H2O; Kl=ph2o/(pH2[%O]) [1] in which 0 signifies oxygen dissolved in the liquid Fe-Cb alloy. The method and equipment of recent studies2,3 were utilized. In brief, the molten alloy, contained in a small crucible, is held in a controlled mixture of steam, hydrogen, and argon until equilibrium is reached. It is then cooled quickly in a stream of helium and analyzed for columbium and oxygen, the latter by vacuum fusion.4 The solubility of the oxide in liquid iron is determined by visual observation of scum formation on the surface of the melt. Crucibles of MgO proved unsatisfactory because of partial reduction at the metal interface. Pure A12O3 crucibles were heavily blackened by the melt and could not be used at high concentrations of columbium. Silica crucibles were more satisfactory but these introduced some silicon into the melt thus necessitating an uncertain but small correction for its effect on the activities of the other solutes. In silica it was possible to observe the scum formation when the melt became saturated and there was no apparent reaction between scum and crucible. The procedure for saturated melts was as follows. The alloy charge composed of electrolytic iron and columbium grain was melted and held at constant temperature. The gas ratio H2O:H2 was progressively increased by raising the saturator temperature until a point was reached at which a bright film appeared on the surface and covered it completely. This film could be dissolved by raising the temperature of the melt and it reappeared when the temperature was lowered. Under a partial film covering, utilizing bare areas for temperature measurement, the melt was brought to equilibrium with the atmosphere by holding at temperature for about 1 hr as suggested by Dastur.5 INTERACTION IN THE MELT Several experiments were made without columbium to establish a base in silica crucibles. The results are shown in Table I. Except for one run, they agreed well with Floridis1 comparable results in other crucibles. The value of log K1 is taken from Table I as 0.58. This is slightly larger than Floridis' result, probably because of less elaborate safeguards against thermal diffusion. Results obtained in the Fe-Cb-0 series in which no scum formed are shown in Table 11. The equilibrium ratio Kl is defined as ph2o/(ph2[%O]). It is related to the equilibrium constant K1 as follows:

Jan 1, 1962

By V. M. Dobrynin

Experimental data demonstrate that physical properties of porous rocks change under pressure. In this paper an assumption is made and proved that under pressure the changes of physical properties such as porosity, density, permeability, resistivity and velocity of elastic waves are controlled to a large extent by the pore compressibility of rocks. It is also shown that the pore compressibility of rocks can be determined, within the range of pressures from 0 to 20,000 psi, by knowing the maximum pore compressibility and the magnitude of the pressure. Mathematical equations were developed which permit one to define changes in physical properties of porous rocks under pressure. These equations were verified by experimental data obtained from the study of sandstones. INTRODUCTION In studying the behavior of porous rocks under pressure in the field of petroleum technology, the most interesting aspect is the observation of those properties which characterize the rocks as possible reservoirs — for example, porosity, permeability, resistivity, density and the velocity of elastic waves. The literature dealing with this problem mainly contains data concerning the study of only one or at most two of these parameters, but not of the group as a whole. An attempt is made in this paper to find general equations involving each of these parameters, which will permit the study of the behavior of rocks under pressure. All experimental data used here were obtained from the investigation of consolidated sandstones. EXPERIMENTAL In addition to the use of published experimental data, an experiment was carried out which studied the main physical properties of sandstones under pressure. Two homogeneous quartz sandstones were chosen for this purpose: (1) the Torpedo sandstone from Kansas, and (2) the Medina sandstone from Ohio. The porosity of the Torpedo sandstone was 20.2 per cent, and that of the Medina 8.7 per cent. Permeabilities were 45 md and less than 1 md, respectively. Each sandstone contained about 5 per cent clay minerals, consisting mostly of kaolinite and chlorite, which were distributed quite evenly throughout the samples. One cylindrical sample 2 in. in diameter and 5 in. in length was cut from each sandstone and then saturated in a vacuum with a 3N solution of NaC1. This high concentration was used in order to obtain true formation factors and to decrease the swelling of the clay minerals. The methods of mounting the samples and measuring the changes in porosity and resistivity were practically the same as those described by Fatt and Mann.1,2 Changes of resistivity under pressure were studied for sandstones with 100 per cent water saturation, and for sandstones with the irreducible water saturation. The irreducible saturation was obtained by enclosing the saturated rock samples in relatively fine silicate powder so as to remove the water by capillary action. This procedure is described by Orkin and Kuchinski.3 Changes of permeability with pressure were determined at room temperature using nitrogen as the flowing medium. In studying the effects of pressure, one series of measurements was made using an internal pore pressure Pi equal to the atmospheric pressure, while the overburden pressure Pe ranged from 0 to 20,000 psi. A second series of measurements was used over the same range of overburden pressure, but with an internal pore pressure of 1,800 psi. When the results were compared on the basis of net overburden pressure (Pe — 0.85 Pi ), there was practically no difference for these two sandstones. The origin of the factor 0.85 in the expression for net overburden pressure is given by Brandt,4 Fatt5 and Geertsma.6 The relatively large bulk volumes of the sample (about 15 cu in.) made it possible to observe a

By N. K. Chen, C. H. Mathewson

Single crystals of high purity aluminum of various orientations were carefully documented after plastic extension. Special attention was given to the formation of slip lines, deformation bands, and asterism. An explanation for the geometry and mechanism of formation of deformation bands is considered. WHILE the general process of plastic extension of face-centered cubic metals is well understood,' the accompanying structural changes due to slip and rotation are far more complex than ordinarily assumed. In the case of stretched single crystals of aluminum, the complicated behavior is especially marked by the formation of deformation bands, as first indicated by Collins and Mathewson." Such bands were believed by them and also by others,".'7 who have discussed banded structure in general, to represent one of the important modes of lattice reorientation and to be intimately connected with the recrystallization process. Yet, despite their fundamental importance to the understanding of the mechanism df both plastic deformation and recrystallization, practically no study of the crystallographic features of these bands in their relationship to the conventional slip process has been attempted. This paper describes part of an extensive investigation on the structural behavior during plastic deformation of aluminum single crystals and is especially concerned with the characteristics of deformation bands. The investigation of the subsequent re-crystallization of deformed aluminum single crystals will be discussed in a later publication. Experimental Procedure Single crystal specimens of 99.996+ pct pure aluminum, Yz in. in diam and 5 to 6 in. in length were made both by the Bridgman method5 nd by a modified temperature gradient method.'* Crystals were selected in which the lineage deviation did not exceed 2"; i.e., as determined from the back-reflection Laue X-ray photograms. These crystals were radiographed to insure that no internal porosity was present. The orientations showed good coverage of the whole area of the Taylor and Elam triangle.' Orientations of the crystals were obtained by the back-reflection Laue technique described by Greninger." Crystals so selected were tapered very carefully in a lathe to obtain a linear decrease in diameter from 0.500 to 0.350 in. along a gage length of 3 in. This is considered desirable because it permits a strain gradient to be introduced in a single specimen at one initial orientation. The advantages of tapered crystals for studying the development of slip lines and recrystallized grains have been pointed out by previous investigators." The cold-worked layer resulting from the machining operation was removed by alternate etching in aqua regia and careful polishing with 2/0 emery paper until undistorted Laue back-reflection spots were obtained. A homogenization treatment at 600 °C for 24 hr was then introduced to insure the removal of residual stress. Two of the crystals so prepared were also checked by use of a glancing angle technique. Using a copper target, at 30 kv and 10 microamperes, a monochromatic beam was positioned at right angles to the axis of the crystal about which it rotated. The time of exposure was 24 hr. From these X-ray photograms, it was concluded that the present method of preparation of single crystals is satisfactory. Following this procedure, the crystals were elec-trolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. Intermittent

Jan 1, 1952

By W. N. Hiatt

The mathematical theory of the flow of two-phase, incompressible fluid through porous media is clarified, and the development of a general fluid displacement equation for two-phase, incompressible vertical flow through porous media is outlined. The relationship between the three components of the equation — the "fluid drive effect", the "gravity effect", and the "capillary effect'' — is discussed, as well as implications of the analysis in connection with the study of certain types of petroleum reservoirs. INTRODUCTION The purpose of this paper is to clarify and summarize the mathematical basis of the theory of two-phase incompressible fluid flow through porous media, particularly as it pertains to vertical flow, and to present a qualitative* exposition of the controlling factors involved in circumstances where this type of flow may exist. Although the generally accepted theory of heterogeneous fluid flow through porous media was developed a number of years ago by Muskat,1 and Buckley and Leverett2, 3 using the basic premise of Darcy, (and since then expounded upon by many others) there is a need for an over-all summary and clarification of this theory, especially regarding certain types of applications in connection with so-called "gravity-drainage-type reservoirs". The source and derivation is outlined for what is referred to here as the "General Fluid Displacement Equation for Incompressible Vertical Two-Phase Flow through Porous Media''. This equation would apply under the condition where the pressure drop along the path of flow is negligible in comparison with the pressure level on the system, or where compressibility and solubility effects are negligible. These conditions exist ordinarily in gravity-drainage-type reservoirs. Specifically, it will be shown that this general equation may be developed directly from the basic equations, which, according to present theory, govern the general case of viscous heterogeneous flow through porous media. This general equation has appeared in the literature previously, but in most cases its development from basic theory is not indicated clearly, or the equation is presented in terms of groups of constants and variables involving reduced or dimensionless quantities. This presentation is expedient in cases of experimental or computer applications; but it may make it difficult for the practicing petroleum engineer to identify all the factors involved or to understand the relationships between them. Therefore, in the following development, only ordinary mathematical parlance will be used, and no terms involving groups of other equations or reduced or dimensionless quantities will be used. DERIVATION The following equations for two-phase oil and gas flow result from analogy with Muskat's general equations,** if solubility and compressibility effects are neglected, and if all volumes are considered in terms of reservoir conditions, and the water phase, if present, is considered to be immobile (or effectively a part of the porous medium.) In this case, the sum of the oil and gas saturations may be taken as unity, and the saturation of each phase is in terms of the total hydrocarbon saturation. Note that in Eqs. 1 and 2, and in the derivation following, z is taken as positive in the vertically downward direction,

Jan 1, 1969

By L. C. Graton

Civilization did not begin until metals became the material of tools, implements and machines. - RICKARD, Man and Metals. HISTORY is no more an end in itself than is a backsight the sum total of a survey. This Institute may view with satisfaction the remarkable development of the mineral industry since its founding three score and fifteen years ago, its own enlarging service to that industry, and the contribution thus made toward the enhanced welfare, opportunity and mutual understanding now in greater or less degree reaching and benefiting all peoples of the globe. But neither this professional society nor the dynamic mining industry as a whole wishes on this anniversary to direct its gaze chiefly toward the past. The foremost purpose of historical review should be to throw into clear perspective the strong points and the defects in the forward march thus far, primarily as the basis for conceiving and designing a still sounder progress henceonward. At various times since the Institute's founding, the theories of ore deposition have been considered from the historical view point.l-7 For the present occasion it seems fitting to lay prime emphasis on the practice and utilization of geology in its varied relations to the problems of the mining industry. It is hoped that the reader will understand and accept the degree to which the whole is sampled by parts familiar to the present writer, and the disproportionate attention to thought and achievement within the United

Jan 1, 1947

By Charles L. Mantell, James E. Hoffmann

Mechanical inclusion, electrophoretic deposition, and adsorption were studied as mechanisms for code-position of aluminas present in copper-plating electrolytes as an insoluble disperse phase. Mechanical inclusion was not a significant factor. That codeposi-tzon of aluminas by an electrophoretic mechanism was unlikely was substantiated by measurements of the potential of the aluminas. The alumina content of the deposits was studied as a function of the pH of the bath. These tests in conjunction with sedimentation studies demonstrated the absence of an isoelectric point for the alutninas over the pH range examined. Thiourea in the electrolyte (a substance known to be adsorbed on a copper cathode during electrodeposition) affected the amount of alumina in the electrodeposit. However, no adsorption of thiourea on aluminas in aqueous dispersions was detected. If it were possible to produce a dispersion-hardened alloy of copper and alumina by electrodeposition, an alloy possessing both strength and high conductivity at elevated temperatures might be anticipated. Investigation of the mechanism of codeposition of aluminas with copper was undertaken with the hope that knowledge of the mechanism would aid in the development of such an alloy. The word "codeposit" here does not necessarily imply an electrolytic phenomenon but rather that the materials codepositing, the various aluminas, are transported to and embedded in the electrodeposited copper by some means. Mechanical inclusion in electrodeposition implies a mechanism of codeposition which is wholly mechanical in nature; the only forces acting on a particle are gravity and contact forces. Such a particle is presumed to be electrically inert and incapable of any electrical interaction with electrodes in an electrolytic plating bath. Processes for matrices containing a codeposited phase by electrodeposition from a bath containing a disperse insoluble phase frequently state that code-position is caused by mechanical inclusion.10,2,12 If settling, i.e., gravity, be the controlling mechanism for codeposition of aluminas, then assumptions may be made that 1) the content of alumina in the electrodeposit should be enhanced by increasing the particle size, 2) the geometry of the system, that is, the disposition of the cathode surfaces relative to the di- rection of the falling particles, should affect the alumina content of the electrodeposit, 3) in geometrically identical systems the chemical composition of the electrolyte employed should exercise no effect on the alumina content of the deposit, that is, the alumina content should be the same in all cathode deposits irrespective of bath composition. A bent cathode19 evaluates the clarity of filter effluent in electroplating baths by comparing the roughness of the deposit on the vertical surface with that on the horizontal surface. Two difficulties are inherent in this technique: 1) the current density on the horizontal portion of the cathode would be substantially greater than that on the vertical surface; 2) should the deposit obtained be rough, projections on the vertical face could act as horizontal planes and vitiate the relationship between the vertical and horizontal surfaces. Bath composition should have no substantial effect on the alumina content of the deposit. Two different electrolytic baths were employed. They possessed variant specific conductances and substantially different pH ranges. The experimental tanks were rectangular Pyrex battery jars 6 in. wide by 3 1/4 in. long by 9 3/4 in. deep. The cathodes were stainless steel 316 sheet of 0.030 in. thickness, cut to 7.5 by 1.75 in. and bent at right angles to form an L-shaped cathode whose horizontal surfaces measured 1.75 by 3.0 in. All edges and vertical surfaces were masked with Scotch Elec-troplaters Tape No. 470. The anodes were electrolytic cathode copper 9 in. high by 2.25 in. wide by 0.5 in. thick. To eliminate inordinately high current densities on the projecting edge of the cathode, the anode was masked 1 in. above and below the projected line of intersection of the cathode with the anode. The exposed area of the anode was equal to that of the cathode, providing both with equal average current densities. The agitator in the cell was of Pyrex glass and positioned so its center line was equidistant from cathode and anode, and a plane passed horizontally through the center of the blade would be located equidistant from the bottom of the cathode and the bottom of the deposition tank. The assembled apparatus is depicted in Fig. 1. Hatched areas on anode and cathode represent the area of the electrodes wrapped with electroplaters tape. MATERIALS The chemicals were copper sulfate—CuSO4 • 5H2O— technical powder (Fisher Scientific Co.). Spectro-graphic analysis showed substantial freedom from antimony, arsenic, and iron. Traces of nickel were present.

Jan 1, 1967

By A. W. Dana, F. J. Shortsleeve, A. R. Troiano

The phenomenon of flake formation which may occur during cooling or room temperature aging of large steel sections is caused by a combination of hydrogen and stress. As such, the transformation characteristics of austenite in a particular section play a major role in the occurrence of flakes. Isothermal and continuous cooling studies demonstrated that flake formation is particularly sensitive to nature, distribution, and relative proportions of the microconstituents in the cooled sections. In the absence of transformation stresses, abnormally high hydrogen contents could be tolerated without flaking. Flakes were not found in the absence of transformation stresses. No correlation existed between average hydrogen content and flake formation where cooling stresses were low. Hydrogen in the steel was a necessary but not sufficient condition for flake formation. DESPITE a long history of laboratory and commercial investigations, the mechanics of hairline crack or flake formation in large steel sections remains unresolved. Recent publications1-5 emphasize that flaking is still a serious problem.* immediate cause of flaking is the pressure exerted by entrapped hydrogen gas that collects in small internal cavities or voids during cooling. When the temperature of steel is low enough to preclude extensive plastic flow, the cavity pressures cause local brittle fractures (flakes). 2—The microsegregation and transformation stress theory. According to this theory, flaking results from stresses arising from the volume changes accompanying the formation of martensite and/or low temperature bainite after a large portion of the section has transformed at elevated temperatures. The proponents of the hydrogen theory suggest that stresses from other sources may be additive to the stresses produced by hydrogen and may, in some cases, provide the increment of stress necessary to produce flakes. However, the critical aspect of this theory is that no stress, except that produced by hydrogen pressure, is believed to be sufficient in itself to produce flakes. For practical considerations, this means that the only safe thermal cycle is one that reduces the hydrogen content to some low critical level below which flaking will not occur regardless of the state of transformation. On the other hand, the transformation stress theory does not rule out the embrittling effect of hydrogen. This theory simply proposes that flaking does not occur in the absence of transformation stresses. With the transformation stress theory as a basis, commercial antiflaking cycles would be designed to complete the transformation of austenite prior to cooling to ambient temperatures. Both of these theories appear compatible with industrial experience. Antiflaking cycles, such as cooling at extremely conservative rates or soaking for periods of time in the upper subcritical temperature ranges prior to cooling to ambient temperatures, may allow the following: 1—diffusion of hydrogen out of the section and, as a consequence, reduction of the hydrogen content to some safe minimum value (hydrogen pressure theory) and 2—complete decomposition of the austenite at rela-

Jan 1, 1956

By Harry V. Welch

Early in the development of the art of metallurgy, it was noted that a distinct difference existed in the character, collection possibility and health hazard of the "smoke" from lead furnaces and those from copper plants. Zinc-plant fumes, although not so detrimental to health, were closely allied in nature to those of the lead works. In Cottrell plants, there are sufficiently distinct differences in operation and amount of construction between those for lead and copper to justify their consideration under separate headings; therefore, while the application of the process at copper-reduction works was covered by the writer some two years ago in the Transactions1,† this discussion will confine itself more distinctly to "fume" collection. General information on the process has been presented in numerous articles and by many authors: Cottre112, Schmidt3, Bradley4, Anderson6, Labbe6, Shiga7, Rathbun8. "Fume" may be defined as material, metal or nonmetal, elemental or compound, evolved as a vapor from a furnacing or chemical reaction and condensing, chilling or reacting within the gas stream to yield a solid form, and in this definition liquid particles are solids in a sense as distinguished from gases or vapors. Such condensed particles are of minute form, on the order of "smoke," and, for example, on the order of a few hundredths of 1 micron (1 micron = 1/25,000 in.) to perhaps 3 microns, with agglomerates, in relatively small proportions of many particles. Metallurgically typical fume products are lead compounds, oxides, carbonates and sulphates; elemental zinc, more commonly encountered as a fume particle of zinc metal with a surrounding "skin" of zinc oxide; arsenic, both metal and oxide and some of its more complex salts such as added sulphates as found in flue dusts; antimony, more particularly its oxide forms; and elemental sulphur, sometimes a troublesome product, in Dwight-Lloyd sintering-plant fumes. These products, particularly the elemental or lower oxide forms, have relatively appreciable vapor pressures at the existing operating temperatures as reported by Welch and Duschak9, Ingold10, Johnstonll, Millar12,13.

Jan 1, 1937

By E. L. Mann

Asbestos is the generic name given to a group of fibrous mineral silicates found in nature. They are all incombustible and can be separated by mechanical means into fibers of various lengths and cross sections, but each differs in chemical composition from the others. The commercial grades of asbestos consist of a spectrum of lengths and sizes and are not definitive as are most organic fibers. It is generally recognized that there are two main groups of asbestos. The first only contains the fibrous serpentine called chrysotile and comprises about 94% of the world production of asbestos. The second group contains five minerals in the amphibole series-crocidolite, amosite, anthophyllite, tremolite, and actinolite. The latter two have no commercial importance. Properties Physical The structures of asbestos fibers have been studied intensively over a number of years. X-ray diffraction patterns have been used as a means of identification and classification. Low angle X-ray scattering techniques have shown that chrysotile fibers are "hexagonally close packed" and parallel to each other, having cross-sectional diameters varying from 18Å to 300 Å units, while the amphibole fibers are many times larger in cross section, have considerably smaller surface areas, and the fibers are less symmetrical than those of chrysotile. Electron micrographs of the more common types of asbestos are shown in Figs. 1-4. Fig. 1 illustrates the softness and flexibility of chrysotile which make it suitable for textile-type products. For a number of years there was considerable controversy over the exact nature of chrysotile fiber, but the photographic evidence in Figs. 5-7 clearly show that it is tubular in structure. The curvature is the result of the mismatch in the dimensions of the silica [Si2O5] and brucite [Mg(OH)2] layers which are on the inside and outside, respectively, of a double sheet. This curvature had been predicted by Pauling (1930) years ago based on the molecular dimensions of the two component structures. In contrast to this, the structure of the amphiboles consists of two ribbon chains based on Si4O11 units separated by a band of seven cations with two hydroxyl groups attached to

Jan 1, 1983

By Murray Kaufman

Using en; 41 for a base alloy, 15 modifications were made in sheet form. The elements Al, Ti, C, Mo, Co, and Cb were varied. The effects on the phases formed and their temperature dependence, the aging characteristics, tensile and stress-rup- ture properties, and weld cracking were determined. The A1-Ti content and balance is the most important factor influencing the major sCrengthening phases [Ni,Ti and Ni,(Al, Ti)] and, consequently, mechanical properties. THE mechanical properties, fabricating and joining characteristics, dimensional stability, and so forth, of alloys containing secondary phases are largely determined by the phases present, their distribution, and their temperature dependence. The phases in the basic ternary and quaternary Ni-Cr-Al-Ti combina- tions have been investigated thoroughly.'* The phase behavior of many commercial nickel-base alloys has been determined also. In some cases, for example U500, 5 the effect on mechanical properties has been found. However, little systematic work has been done to clarify the action of each of the important alloying elements in controlling the phases formed in complex commercial alloys and their behavior. The effect of molybdenum on the carbides formed in M252 was investigated by Beattie and verSnyder.6 Application of the results provided by that work

Jan 1, 1963

By L. K. Jetter, J. C. Ogle, C. L. McHargue

The preferred orientation developed in extruded aluminum rods has been studied as a function of extrusion temperature, extrusion speed, and position in the rod. Duplex <111> - <001> textures were developed for slow extrusion speeds at temperatures of 75° to 850° F and for fast extrusion speeds at temperatures of 75° to 450°F. The <001> texture component was shown to be primarily due to re crystallization occurring during fabrication. At fast speeds and billet temperatures of 650° to 850°F, complete recrystallization occurred and <115>or<118> textures were found. The nature of the structure has proved to be an important variable in the production and use of extruded products. Data on the flow of aluminum and aluminum alloys summarized by Smith,&apos; Hardy,&apos; and Locke3 show that the extruded product may possess a deformed, a partially recrystallized, or a completely recrystallized structure, and there may be important variations in the structure from surface to center and from front end to back end of an extrusion. This inhomogeneity in grain structure and preferred orientation affects both the mechanical properties of the extruded section and its response to subsequent heat treatment. Among the fabrication variables causing these differences are temperature, extrusion ratio, and extrusion speed. Preferred orientation which develops during the extrusion of rods is of the fiber-type and, in general, has been assumed to be similar to that developed in rods or wires fabricated by drawing through dies, rolling, or swaging.4 Because of the nature of the flow of metal being extruded, this assumption may be valid for material near the center of the rod but probably is not valid for the outer layers. In most face-centered-cubic metals a duplex fiber texture has commonly been reported in which the grains have either <Ill> or <001> directions parallel to the longitudinal axis. Sachs and fichiebold5 reported cold-drawn aluminum (99.6 pct pure) to have a single <Ill> fiber texture, and this observation was confirmed by Schmid and Wassermann.6 Hibbard, on the other hand, observed a minor <001> and a major <111> texture in 99.994 pct A1 cold drawn to 98 pct reduction in diam.7 He concluded that the <001> component resulted from a small amount of room-temperature recrystallization. Dayal8 concluded that the <001> component was an intermediate component which disappeared at high reductions in 99.5 pct pure Al. Kostron and schippers9 found duplex <111> — <001> textures in extruded 99.5 pct Al, as did Gow and cahnl0 and GOW11 for extruded rods of commercial and superpure aluminum. Similar duplex fiber textures have been reported for aluminum alloys by Kostron,= Unckel,13 and Van Horn.14 The present paper is concerned with the variation in texture with fabricating conditions and with the nature of the texture components in extruded aluminum rod (99.99 pct pure). EXPERIMENTAL PROCEDURE Ingots were chill-cast in cast-iron molds and machined to 3-in. diam by 6-in. long extrusion billets. These billets were upset to 3.125 in. diam and extruded through a flat-face 0.690-in. diam die. Quenching of the rods was accomplished by a water spray at the die face. The combinations of fabricat-

Jan 1, 1960

By E. T. Turkdogan, P. Grieveson

Experimental results are given for the rate of oxidation of ferrous iron to ferric iron in pure molten iron oxide by carbon dioxide + carbon moloxide mixtures at 1550°C. It is shown that the rate-controlling process is the interdiffusion of iron and oxygen atoms within the melt. The inter-diffusivity of iron and oxygen in the melt is obtained from the results and the value of (5.0 * 1.0) x 10-5sq cm per sec is recommended for the temperature of 1550°C. Similarly, it is also found that the rate of reduction of molten iron oxide is con -trolled by diffusion in the melt; however, apparent interdiffusivity values from these experiments are 10 to 20 pct higher than those obtained in the oxidation experiments, by virtue of convection arising from density difference. The results of the oxidation experintents are used to calculate an estimated self-diffusivity of iron in molten iron oxide of (1.5 * 0.5) x sq cm per sec. BECAUSE of the industrial importance of iron oxides, the study of the kinetics of both the reduction and oxidation of the solid oxides has received a great deal of attention. However, knowledge of the kinetics of similar reactions in the liquid state is very meager. Dancy 1 studied the kinetics of reduction of molten iron oxide by carbon in pig iron and found that the reaction is very fast. It was concluded from the results that the reduction of molten ferrous oxide is a first-order reaction up to 80 pct reduction, while

Jan 1, 1964

By E. J. Koval

Practical miscible displacement processes will be characterized by lingering of the solvent into the oil. The lingering process is brought on by viscosity differences, and can be accentuated by channeling and longitudinal dispersion. The effects of these factors on the efficiency of unstable completely miscible displacements are combined in what is called the K-factor method. This method, analogous to the Buckley-Leverett method, predicts recovery and solvent cut as a function of pore volumes of solvent injected. Experimental data are included and show excellent agreement with theory for a wide variety of sandstone cores and viscosity ratios. INTRODUCTION Theoretical considerations,1 laboratory experiments,2 and pilot tests3 lead to the conclusion that miscible displacements in the field will be unstable In an unstable miscible displacement, the solvent fingers through the oil. This fingering leads to early breakthrough of the solvent and an extended period during which both oil and solvent are produced. For such a system, there appear to be four principal factors which bring about or accentuate the effects of instability: longitudinal dispersion (including geometrical effects), channeling, viscosity differences and gravity differences. Other factors, such as diffusion and flooding rate, can also influence the effects of instability, but at the flooding rates considered in this report, circa 15 ft/D, they are unimportant. Longitudinal dispersion can be thought of as a spreading of the solvent front caused by the presence of microscopic inhomogeneities. Channeling of the solvent occurs when a porous medium has macroscopic inhomogeneities; i.e., gross permeability variations. Viscosity differences lead to fingering of the less viscous solvent. This difference in viscosity accelerates the growth of fingers along paths previously developed because of permeability variations. Gravity differences lead to overriding by the usually less dense solvent. Al- though gravity effects are generally small at a flooding rate of 15 ft/D, they would, nevertheless, unnecessarily complicate the interpretation of flooding experiments. For this reason, all the experiments reported herein were done with matched density fluids. Fingering and the resultant poor areal sweep were recognized early as the dominant influences on the efficiency and the economics of miscible displacement processes. Much research effort has been spent on ways to minimize fingering and increase areal sweep such as the use of graded viscosity slugs4 or water slugs. Some researchers attempted to work out ways to prevent fingering completely; i.e., to achieve a stable displacement through gravity or latitudinal dispersion stabilization. l Others did not attempt to control fingering but obtained an economic process by merely recycling the solvent and sweeping pattern by pattern.6 During this period, all aspects of fingering came under close scrutiny. Some researchers reported on how fingering looks2 and how it is affected by viscosity ratio,7 geometry,7 and slug size.2,* Peaceman and Rachfordg suggested a mathematical approach to the prediction of unstable miscible displacements in relatively homogeneous sand packs, but their work cannot be extended conveniently to heterogeneous systems. Hence for a heterogeneous system, no method is presently available for predicting solvent cut and recovery as functions of pore volumes of solvent injected. The purpose of this investigation was to attempt to fill in the gap in our knowledge concerning the prediction of performance of unstable miscible dis placements. Necessarily, the system selected for study was a relatively simple one. The restrictions placed on the system were: (1) The system was linear; (2) The solvent was miscible in all proportions with the oil in place; (3) The solvent was continuously injected into the porous medium; (4) Gravitational effects were eliminated by matching densities and (5) All the flood rates were high and constant at 15 ft/D to avoid any small rate effect and to minimize any diffusion effects. To simplify and to indicate that both longitudinal dispersion and channeling arise from permeability variations, the effects which they cause or influence have been termed heterogeneity effects. The use of

By H. C. Chang, N. J. Grant

REEP studies and measurements in most in-V> stances are based on a relatively gross gage length. Even in some recent theoretical studies on the mechanism of creep, changes were followed by means of X-rays and metallography without regard for the behavior of the individual grains and grain boundaries.&apos;" Analytical studies of creep have frequently indicated that more than one competing process is operative and that the ultimate creep performance depends on the effects of temperature, time, and strain rate as well as grain size.&apos;-" he grains and grain boundaries are known to respond differently to these variables but the extent of the response is still little known, especially in poly-crystalline materials where the relative orientations of grains and grain boundaries are important. This paper reports some experimental observations of the behavior of the grain boundaries and their effect on the deformation in the grains. High purity aluminum was used to avoid complications of aging reactions, second phase, inclusions, etc. Experimental Procedure A small vertical nichrome wound furnace was built to permit direct loading on the test specimen. This furnace is capable of operating up to about 1300°F with reasonable temperature distribution. A ground rectangular quartz window, 1.25x0.5 in., is imbedded in the external stainless steel tube to permit observations of the creep process with a microscope. An argon atmosphere ,was provided to prevent oxidation. The quartz window caused a temperature gradient between the back and front surfaces of the specimen of 15" at 700°F. The temperature gradient could be cut down to 3°F along the length of the specimen by adjusting shunts across the furnace windings. An ordinary metallurgical microscope with a working distance of 14 mm was rebuilt so that it could be moved in three mutual perpendicular directions. Visual examination could be made with either a 30X eyepiece or a 15X filar eyepiece. Using an objective of focal length 24.3 mm and a numerical aperture 0.20 a total magnification of 120X or 240X could be obtained. High purity aluminum rated at 99.995 pct was supplied by the Aluminum Co. of America as % in. then the gage portion was further machined to 3/16 in. diam. The ends were Y4 in. diam and threaded to fit available specimen holders. Two opposite flat surfaces of the gage portion were obtained by milling, giving final dimensions of the gage portion of 3/4x3/16x3/32 in. Machined specimens were first electropolished in Jacquet&apos;s solution.&apos; Reference marks were produced by pressing a thin sewing needle into the surface of the specimen. The specimen was then annealed at 900°F for 24 hr and at 1150°F for 12 hr. Typical macrostructures of specimens treated in this manner are shown in Fig. 1. The range of the grain size was 1 to 5.5 mm (see Fig. l), but most of the grains were of 2.5 mm and went through the whole thickness of the specimen. The specimen was re-electropolished and etched electrolytically to reveal the grain boundaries. In order to reveal the orientation difference of the grains, etch pits were produced on the surface of the grains by etching in a mixture of hydrochloric and nitric acids (HC1, 45 pct; HNO,, 10 pct; H,O, 45 , by volume). The specimens were very carefully put into the holders and furnace; yet even with this care, fine slip lines were developed on the specimen surface.

Jan 1, 1953

By E. Buehler, J. E. Kunzler

High-pu.1-ity molybdenum has been heat treated, melted, and zone refined and the physical and chemical changes that are produced by these processes have been studied by making resistance ratio measurements. Pronounced effects are observed that are associated with recrystalliza-tion at about 1200°C and with melting. Melting alone is found to result in a substantial purification by the evaporation of impurities such as iron. Zone refining is found to be reasonably effective with four passes producing a three-fold decrease in resistance ratio and a minimum ratio of 0.0003. With the aid of low temperature measurenzents, it has been shown that the build-up of a deposit of the material being zone refined on the radio frequency coil used for heating can lead to contamination of the sample. CONSIDERABLE interest in high-purity refractory metals for the study of mechanical properties has developed during recent years. Also the need for highly pure metals in certain fundamental studies, such as electronic band structure, has become quite widely appreciated. Molybdenum can now be produced with sufficiently high purity to make it attractive for such investigations. The most suitable measure of chemical purity of metals used for many of these studies is its resistance ratio, R,.,o,/Ro, During the purification of molybdenum by zone refining and its subsequent evaluation by this technique, a number of informative observations were made. These observations concern the effectiveness of zone refining, the volatilization of impurities at the melting point, and the recrystallization of molybdenum and appear to be pertinent to other refractory metals. Also, the usefulness of low-temperature resistance measurements as an analytical tool for evaluating the presence of chemical impurities and physical defects in metals is again illustrated. Samples of high-purity molybdenum of known mechanical history were heated to various temperatures between 800°c and their melting point. Resistance ratios of the samples were measured after they had been given a specified treatment. The data were used, along with mass spectrographic analysis, as an aid in interpreting the nature of the processes that occurred in conjunction with each treatment. Changes in the concentrations of chemical impurities and physical defects are typical of things that effect the low-temperature resistivity. SAMPLES The starting material was obtained from Westing-house Corp., Bloomfield, N.J. It was in the form of molybdenum rods, usually 1/8 or 3/16 in. in diameter. These had been previously processed from bars, 5/8 in, in diameter, originally reduced from 4 in. diam arc-cast ingots, by hot swaging at about 1300°c. In the final step, the temperature was lowered to about l lOO°C which resulted in the production of elongated grains. Typical grains were about 0.03 mm thick and 0.6 mm long. The molybdenum was quite pure as is indicated by the results of mass spectro-scopic analysis1 given in Column 2 of Table I. Other nongaseous elements not listed in the table were not detected. ZONE REFINING AND THERMAL TREATMENT OF SAMPLES Several sample rods, 8 to 10 in. long, were zone refined or were heat treated at several temperatures. Both types of operations were performed using 3 me-

Jan 1, 1962