Search Documents

By N. Jaffe, J. E. Dorn

The effect of stress on the creep rate of high-purity poly crystalline aluminum in the intermediate temperature range was investigated by conducting creep tests at a series of different stresses and by decreasing the stress abruptly during the course of primary and secondary creep. Three series of decreases in stress tests were conducted: the stress was decreased in primary and secondary regions of creep at 347.5°K and the stress was decrensed in primary creep at 327°K. The results demonstrate the effects of structure and temperature on the stress dependence of the creep rate. The trends in the creep rate after a drop in stress are complicated and show that recovery takes place. The experimental results were compared with Friedel's theory for cross-slip, the experimentally determined energy for a constriction being in good agreement with the theoretical estimate proposed by Stroh. PREVIOUS investigations have shown that the ap-- parent activation energy for creep of polycrystalline aluminum, over the range from about 250° to 380°K, is approximately 27,400 cal per mole,' a value that is to a first approximation insensitive to the applied stress, the creep rate, and the creep strain. Several facts strongly support the thesis that creep, in this temperature range, is controlled by the rate-determining mechanism of cross-slip: 1) Recovery of the cold-worked state can take place by a number of mechanisms prominent among which is climb and cross-slip. Astrom2 reported rapid recovery of cold-worked polycrystalline aluminum at 340° to 370°K giving an activation energy of 28,000 cal per mole and additional recovery at the higher temperatures of 455° to 478°K giving an activation energy of 36,000 cal per mole. Whereas the latter process was clearly identified with the climb mechanism, the former process. which has an activation energy in good agreement for that of creep in the same temperature range, is most likely due to recovery by thermally-activated cross-slip. 2) Single crystals of aluminum exhibit sharp slip-

Jan 1, 1962

By David Mitchell

MANY of the difficult operating problems of the preparation of coal for market, of sampling coal shipments and in the utilization of coal are caused by segregation in the coal mass. Segregation may be of two kinds: i.e., "size segregation," in which parti- cles of the same size in a mass of coal containing a range of sizes collect to-gether and "density segregation," in which particles of the same density or specific gravity in a mass of particles of varying density gather together. MECHANICS OF SEGREGATION Size segregation cannot take place with closely sized coal. As the size range increases, the tendency for size segregation increases. Similarly, cleaned coal with particles of approxi- mately the same specific gravity have very little tendency for density segrega- tion. The wider the density range of particles and the more particles of different density, the greater the chances are for density segregation. FIG. 1.-SEGREGATION IN A SIDE-FILLED The following discussion deals primarily BIN with coal of a wide size range as screenings and of wide density differ-ences as uncleaned or run-of-mine screenings. If a mass of coal containing particles of a wide size range is subject to the stream action of a moving current of water, the small particles are transported farther than the coarser. Particles of different density in a stream of moving water are subject to the laws of classification, the heavier settling out first. The familiar sluice box of the gold miner and the action of rivers and other streams in classifying material according to

Jan 1, 1937

By E. H. Edwards, J. Washburn

Zinc crystals were deformed in simple shear and it was found that anisotropic strain hardening occurred in which the inactive slip systems were hardened more than the active system. The formation of dislocation barriers by dislocation interaction was discussed as a possible explanation of the hardening of the latent systems. STRAIN hardening which accompanies slip in a metal crystal is not limited to the slip systems actively contributing to the plastic strain. There is also a strengthening of the latent slip systems which are crystallographically equivalent to the active system. In the case of aluminum deformed in tension, Taylor and Elam1 found that plastic flow on one set of octahedral planes caused either the same or a slightly greater hardening on an inactive set. Similar results have been obtained for crystals of a brass2 and of Cu-A1 solid solutions.3 Experiments by Rohm and Kochendorfer4 indicated that the hardening of the active system exceeded the hardening of any latent system for aluminum crystals deformed in shear. On the other hand, strain hardening in zinc and cadmium crystals tested in simple shear at —196°C was recently found to be greater in the latent than in the active slip direction." When the strain direction was shifted during testing to a direction 60" from the original, a higher stress was required for glide to continue than would have been needed for flow to proceed in the original direction. The relation between the hardening of active and latent systems must be complex, depending upon the relative orientations of the systems and upon the experimental techniques used to deform the crystal. A detailed knowledge of the hardening produced in latent systems would be valuable in choosing between possible dislocation models of the strain-hardening process. The experimental data now available are incomplete and even contradictory. The present study was undertaken to provide quantitative information regarding the relative amount of hardening of active and latent systems for a particularly simple case. Zinc crystals were deformed in simple shear along one of the three crystallographically equivalent directions [250], [1210], and [1120] in the slip plane, and the relative hardening produced in each of these directions was compared. Experimental Procedure and Results The single crystals of 99.99 pct purity zinc used in this investigation were grown from the melt in the form of 1 in. diam spheres. Shear specimens were acid-machined from the crystals by a method which has been described previously. The gage section of the test specimen was a cylinder having a height of 1/8 in. and a cross-sectional area of approximately 1/3 sq in. All specimens were machined with the axis of this cylindrical gage section aligned with the [0001] axis of the crystal. An innovation in the design of the shearing apparatus for these tests was the provision for a rapid shift in the direction of the applied stress from one slip direction to any other slip direction lying in the same slip plane. Fig. 1 shows a section through the specimen and shearing apparatus, and Fig. 2 is a

Jan 1, 1955

By F. W. Glaser, W. Ivanick

A pressure-sintering method was used to produce binder-free and very dense TiC specimens. Some physical properties of these TIC bodies were determined and found to compare favorably with those of certain cemented Tic grades. It was also observed that the hot transverse rupture strength of TiC bodies remained substantially the same regardless of the amount or type of binder material used. STUDIES of the structure and physical properties of refractory materials have been intensified recently because of the urgent need for nonstrategic materials that retain their strength at high temperatures. Research aimed at determining and improving the physical properties of cemented carbides and borides has been accelerated with a view toward possible use of such materials in connection with turbine blades, rocket nozzles, and other high temperature applications. On the hypothesis that the strength requirements in connection with some of the above applications could be met only by proper choice of cementing agents for such refractory materials, the literature describing the physical properties of borides or carbides was reviewed. However, with a few exceptions,'-" references were found only to compositions containing at least one or more auxiliary binder metals. Cobalt and nickel are among the most frequently employed cementing agents. The melting point of Tic (approximately 3250°C) and therefore the sintering temperature, at which notable densification of a cold pressed Tic powder compact could be expected in the absence of a liquid binder phase, is relatively high. The present study makes use of a high temperature, pressure-sintering procedure, recently described by one of the authors in connection with the sintering of binder-free ZrB,," to produce dense bodies of sintered Tic—free of any cementing agent. During the course of this sintering study, some physical properties of dense Tic bodies produced by this method will be discussed. Materials, Preparation of Samples, Testing Methods The procedure for the forming of Tic powder consisted of mixing graphite and TiH, powders in stoi-chiometric proportions, and heating this mixture in a H, atmosphere and carbon crucible by high frequency, to temperatures ranging between 1900° and 2100°C (3452" and 3812°F). The powdered carbide was then comminuted and screened to the desired particle size. Table I shows the chemical analysis of the two grades that were employed for the production of samples during this work. Bodies of Tic, approximately 2.5xlx0.5 cm were produced in graphite molds that were heated by direct conduction. Sintering was carried out at temperatures for time intervals ranging from approximately 0 to 30 sec under a constant pressure of about 1.3 tons per sq in. An alternate method for the production of samples consisted in cold pressing the individual Tic grades at pressures ranging from 4 to 10 tons per sq in. and sintering in a hydrogen atmosphere in graphite crucibles heated by high frequency induction. Sintering temperatures ranged from 2600° to 2900°C (4715° to 5255°F). Electrical testing was done by measuring potentiometrically the voltage drop over a length of 1.5 cm for a current of 10 amp at room temperature. Cross-sectional areas as well as densi-

Jan 1, 1953

By Klaus Emicke

The paper describes the lead refining process operated at Norddeutsche Affinerie (N.A.). Incoming materials are different grades of lead with varying percentages of impurities: Cu, Te, As, Sn, Sb, Bi, precious metals. The facilities are designed for charge-wise operation. After drossing, generally Te, As, Sn and Sb are removed substantially by the Harris Refining Process using fused NaOH. A certain selectivity during refining is achieved by controlled addition of NaNO3. Another refining step is decopperizing by means of elemental sulfur. Complete separation of Te, As, Sn and Sb is accomplished by chemical methods in a leaching plant. A Howard Press is used in the Parkes Process for desilverizing. After vacuum dezinking in kettle, Bi is removed, if required, by means of Ca and Mg. In an end refining step Ca, Mg and Zn are removed by having the lead melt treated with NaOH and NaN03. The refined lead as such, or in the form of special alloys, is cast by an ingot casting machine into 50-kg ingots. Zinc which is used as a precipitant in the Parkes Process is recovered by distillation from the high grade Ag-Zn-Pb crystals in Faber du Faur retorts while the Pb/Ag alloy is fed to the cupellation furnace. Ca and Mg are removed from the Ca-Mg-Bi crystals formed in the course of Bi removal, and the Bi-bearing lead is cast into anodes. The electrolytic lead refining facilities at N.A. are operated largely for the purpose of separating Pb and Bi. These facilities are also used particularly for the refining of Bi-bearing lead which had gone through the above process, but from which Bi has not been removed by Ca and Mg.

Jan 1, 1970

By Lawrence Addicks

(San Francisco Meeting, September, 1915) THROUGH the courtesy of Dr. James Douglas I am permitted to give, a summary of some of the results obtained in leaching slimes tailings in a series of experiments conducted under my direction at Douglas, Ariz.. during the past year. While the test run for which the data are given deals with a particular case, much of the work is general in its application and may therefore be of interest. This work was done upon the ores of the Burro Mountain Copper Co. A description of the geology of the district will be-found in the paper by R. E. Somers published in the May, 1915, Bulletin of the Institute. The mineral is pyrite and chalcocite very finely disseminated throughout the gangue and a characteristic of all the ores is the large amount of alumina present. A representative analysis of the particular ore under consideration would be about as follows: Cu, per cent 2.35 S, percent 3.0 Ag, ounces per ton 0.05 CaO, per cent 0.5 Au None K202, per cent 4.0 Fe, per cent 1.5 SiO2, per cent 70.0 A120,, per cent 13.0 The leaching of the ore direct was early dismissed from consideration for the following reasons: 1. The ore would have to be quite finely crushed to liberate the mineral for leaching; concentrating after crushing would cost but a few cents a ton; and a higher total recovery would result from leaching tailings rather than ore. 2. Rough concentration would yield a suitable material for roasting to make sulphur dioxide or sulphuric acid in connection with the leaching scheme. 3. Such a program put the question of cost vs. recovery on a basis where flotation and discarding of tailings were directly comparable.

Jan 8, 1915

By C. C. Henning

IN any line of human activity logical handling requires an amount of attention to each phase that is in keeping with the importance of that phase. In the complex and rapidly changing field of modern ferrous metallurgy it is difficult to allot the proper degree of attention to the various subjects, and it is not surprising that one or more subjects of major importance should for a time be neglected. Bessemer steel is a good example of a neglected subject. It is largely taken for granted, inferior physical quality is assumed for it, and there is a lack of interest in its technical development and commercial application. Availability of supply is limited. In spite of this technical indifference, limited source and lack of commercial exploitation, bessemer steel con-stitutes a large volume of tonnage in daily use. There is a fairly prev-alent idea even among technical people that bessemer steel survives mostly because of low cost and by reason of a dwindling residue of applica-tions sufficiently common to permit of its use. The difference in cost between bessemer and open-hearth steel is governed largely by the relative cost of manufacture of pig iron and the market price of steel scrap. During the past four years there have been long periods of time during which the price of steel scrap was low enough so that open-hearth steel was considerably lower in manufacturing cost than bessemer. As to application, it may be pointed out that thousands of tons of this material in the form of bessemer screw steel are applied for moving parts in automotive and other equipment. Some forging work and considerable heat treating, particularly carburizing, is performed on this grade.

Jan 1, 1935

By D. W. Brunton

The maps of our large mines are usually prepared with the greatest care; and it is somewhat singular that, in compari~on with the great amount of time and money spent in surveying and platting, 80 little actual use is made of them. Almost the only purpose for which a completed survey-map is afterwards consulted, is the determination of the relative position of the different workings to each other, and to the boundary-lines of the property. After the completion of such a map, it should be made the beginning of another, and in most cases a far more important undertaking, namely, its utilization as a starting-point for a complete inventory of the company's underground possessions. The ordinary mine-survey map, being nothing but a record of what has been done, is, in one sense, only ancient history. To increase its value, such additions should be made as will render it a complete statement of the amount and value of ore in sight at any particular time, and a guide for future development. Comparatively little extra labor is involved in this undertaking, since the larger and most expensive part of the work has already been completed when the mine has been surveyed and mapped. The necessary additions consist in working out and platting on the maps, the geology of the mine as exposed in the workings, in such a manner that the geological survey may be of daily use in the development and operation of the mine. The first step towards the production of a geological map consists in tracing individual level-sheets from the general or composite map. The area to be included, outside of the property in question, will depend very much on local conditions; but, for geological, legal and commercial reasons, it should be extended as far as reasonably practicable. The scale to be

Jan 1, 1906

By Arthur C. Spencer

IN extension of a suggestion already made to account for certain features observed in the Juneau gold-belt in southeastern Alaska,' it is the object of the present paper to indicate in detail certain conditions in which deformation of rocks under their own weight might lead to the production of fractures in which veins could be deposited. A direct, uniformly-distributed pressure of sufficient intensity applied to an elastic brittle mass offering strong resistance to deformation produces rupture. In a material of ideal properties the surfaces of rupture under such pressure would be shearing planes inclined at 45° to the line of force, unless there be preliminary deformation, in which case this angle would be greater than 45°. This general conclusion, resting upon ana¬lytical mechanics, is completely supported by the results obtained by Daubrée in experiments upon the deformation of wax and resin prisms under compression. Let us then first con¬sider one of Daubrée's diagrams. In the case illustrated in Fig. 1, four sets of fractures in two appproximately right-angled pairs (that is to say, in conjugate sets) were produced by end-wise compression of the square cross-sectioned prisms. These fractures cut the axis of compression at approximately equal angles, not varying greatly from 45°. The location of the four sets of fractures is obviously determined by the shape of the prism, since the material in each corner acts in a way as a buttress, permitting the bulging to take place most readily on the sides. By limiting the directions in which bulging may take place, results of a more simple nature could be obtained. Take, for instance, a square prism and place it between two fixed and

Nov 1, 1905

By Nicholas J. Grant, Noboru Komatsu

Metallographic and X-ray studies were made of oxide dispersion strengthened Cu-12 vol pet SiO2 and Cu-3.5 vol pet Al2O3 alloys following time exposures at temperatures approaching the melting. point of the matrix metal. Changes in hardness, oxide particle size and crystal structure were studied to determine the time-temperature stability of these alloys. An interpretation of the mechanism of oxide agglomeration is proposed. One of the most striking features of dispersion strengthened metal-metal oxide alloys is their stability at elevated temperatures, both with respect to recrystallization and maintenance of mechanical properties after exposure at high temperatures. A small amount of work has been done on the re-crystallization phenomenon in dispersion hardened metal-metal oxide alloys'l and several theoretical treatments have been advanced regarding the stability of these alloys by Lenel and Ansell,8 and by Grant and his co-workers.9, 10 This paper reports on metallographic and X-ray studies following various heat treatments of Cu-AI2D3 and Cu-SiO2 alloys at elevated temperatures and the effect of subsequent cold work on the recrystallizalion temperature. An interpretation of the recrystallization behavior of this type of alloy, based on the decomposition and agglomeration of oxides, is proposed. EXPERIMENTAL PROCEDURE Cast ingot bars of copper-1.59 pet Si and Cu-0.77 pet Al, 7/8 in in diam, were annealed in argon for 80 hr at 1000CC for homogenization. The homogenized rods were machined into fine chips and ball milled. Milled particles in the range minus 20 to plus 60 mesh were separated for internal oxidation. The internal oxidation was accomplished by the same method used by Preston and Grant,9 except that the oxidalion temperature for the Cu-Si alloy was 750°C, and for the Cu-A1 alloy was 800°C. These powders were then hydrogen-reduced at 450°C, compacted in a copper container, evacuated at room temperature to 0.04 µ, and sealed for extrusion. They were extruded at 1400°F (760°C) with a ram speed of 55 in. per min for an extrusion ratio of 15.6 to 1 to give a rod 0.38 in. diam by about 3 ft long.

Jan 1, 1962

By J. Bruce Wagner, Roger L. Levin

Integrated forms of two solutions of Fick's second law for the movement of a plane interface through a sample of wustite, and for diffusion into a semi-infinite slab of wustite, are shown to yield nearly identical values of the chemical diffusion coeffcients of cation vacancies in wustite, over the temperature range 900° to 1100°C. The chemical diffusion coefficients, the values of D obtained for the propagation of a concentration gradient through samples of undoped and doped wustite, are obtained from the equations It is becoming increasingly important in metallurgical practices to understand the role of the chemical diffusion coefficient, i.e., the diffusion coefficient of a species across a concentration gradient. During the first stages of sintering, one of the mechanisms by which the bonds between neighboring particles develop is by volume or bulk diffusion. This diffusion coefficient as deter- where ?m is the weight change at any time t, ?W is the total weight change at t =8, A is the area of the specimen, and AC is the total change in the cation concentration after the establishment of equilibrium, as determined by reduction experiments in different carbon monoxide -carbon dioxide mixtures within the limits of existence of the single-phase field. mined from the standard equations for volume diffusion during sintering is actually a chemical diffusion coefficient, and it has been observed to be many times larger than the self-diffusion coefficient as determined on the same materials by experiments using radioactive tracer techniques. Kuczyn-ski1 has noted that, if the controlling mechanism of sintering of A12O3 in an oxidizing atmosphere is the diffusion of oxygen, then this diffusion coefficient as measured from sintering rates is about 2.2 x 104 higher than the self-diffusion measurements obtained by tracer techniques. He has also reported the diffusion coefficient obtained from the rate of sintering of Fe2O3 powder to be about 10 6 times faster than the self-diffusion coefficient of

Jan 1, 1965

By M. Van Siclen

THE outstanding fact in connection with dust disease in the United States at present is the growing recognition of its seriousness by state officials and by the more progressive operators of mining, metallurgical and allied industrial plants. The same may perhaps be said of labor in some of its better organized centers, but the average independent non-union workman continues, as of yore, to suffer the toll of disability and even of death from dust inhalation without realization of the source of his ill-being. Progress in the betterment of the handling of sufferers from dust disease and of the conditions creating dust hazards in mining and allied industries is pursuing a course similar to that of the now widespread campaign against accidents, in which the risk is more obvious, more severe, and was naturally recognized sooner. The coming on of dust disease is generally relatively slow and its immediate effects not infre¬quently masked by or attributed to other diseases. Marked exceptions to this general rule have occurred in districts where the dust is particularly pernicious, such as the Rand and Joplin; yet such exceptions, unhappy in themselves, opened the eyes of medical men, and of those in other localities charged with the responsibility for the welfare of industry, to the much more widespread if less spectacular hazard. existing from the inhalation of dust in all rock-excavating operations and all industrial operations creating inorganic dust, whether it be crushing and grinding, sand-blasting, granite-cutting, or what not. Advancement to date in the United States in prevention and treatment has been slow, yet the record shows that quantitative methods for determining the degree of hazard and means for decreasing it were being developed as far back as 25 years ago; and that more rapid progress may be looked for from now on. In 1908, in this country; F. L Hoffman?(1) discussed the mortality from consumption in dusty trades, especially brass foundries; and in 1913 E. R. Hayhurst(2) described the effects of inhalation

Jan 1, 1933

By Oliver Bowles

WHILE vast quantities of limestone and dolomite. are used in metallurgy, the estimated production in 1926 being 23,860,000 tons, there are many problems connected with their use which have not received adequate study. The literature of metallurgy is notably lacking in comprehensive discussions of fluxing or furnace stone. Approximately 900 lb. of limestone is used for every long ton of pig iron produced in the blast furnace, but this important constituent of the charge receives little attention compared with the intensive study that has been applied to ores and fuels, the other important constituents of the charge. In an effort to elucidate some of the doubtful points, the writer has made a wide review of metallurgical literature, and has had the disappointing experience of finding not more than a paragraph or two on metallurgical stone' for each two or three thousand pages of literature reviewed. Furthermore, the limited information supplied is in some instances contradictory and even absurd. For example, a correspondent in a reputable metallurgical magazine classifies magnesia and silica together as impurities in flux "that must be melted and run off as slag." From the furnace operator's viewpoint it is desirable that as complete knowledge as possible be obtained concerning the effects of chemical composition and physical character of the stone on its action in the furnace and on the quality of the metal produced. A better knowledge of these features is advantageous also to the quarry operator in that it enables him to work more intelligently in producing stone that will best satisfy the metallurgists' requirements. The following pages comprise a brief compilation of data now available. Much of the information is well established and probably acceptable to most metallurgists. On some points there is room for debate, and the chief purpose in presenting a paper at this time is to arouse discussion which will throw more light on controversial points and thus assist the author in preparing a more comprehensive and accurate discussion of metallurgical limestone problems.

Jan 1, 1928

By Shosei Serata

Stress control methods of mining have been developed separately in at least four different parts of the world in entirely different types of mining -- coal, trona, salt and potash -- during the decade of the 1960s. They all utilized yield pillars as tools for ground control. Today, yield pillars are becoming widely used in under- ground mines in a variety of geological conditions. Stress control methods are effective in stabilizing openings in weak, complex grounds, especially at greater depths. Their advantage is that they utilize existing ground media to stabilize mine openings by altering the stress distribution patterns around the openings, by controlling design parameters such as room width, pillar geometry, and excavation sequence, rather than by using a conventional means of artificial ground support such as roof bolts, cribbing, or arches. Stress control methods, therefore, are suitable for both advance and retreat mining, including total extraction mining. Adaptation of these methods results in substantially greater safety, productivity, and ecnomy over conventional methods. These methods are based on scrutiny of the actual stress conditions in the ground, by both in-situ measurement and computer simulation. This paper provides a summary of stress control methods as developed over the last ten years. The field examples are limited largely to salt and potash mining applications, although the method has been used successfully in other mining applications. The examples illustrate that stress control methods actually address general ground weakness problems -- separation at discontinuity planes, swelling by shale expansion, deterioration by brittle fracture, and interference by ground water. That is, although the principle is developed mainly with reference to salt and potash applications, it is generally applicable to weak ground.

Jan 1, 1983

By Robert Anderson

ROUGHLY, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term; it connotes the contraction in volume of a metal or alloy on passing from the liquid to the solid state. Pattern-makers' shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of, sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring tempera-tures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment and technical knowledge of men experienced in the production of castings.

Jan 10, 1921

Discussion of the paper of R. H: Sweetser,. presented at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912 pp. 1327 to 1334. See also Bulletin 11 No. 72, December, 1912, pp. 1561, 1562. J. J. HOWARD, Dover, N. J. (communication to the Secretary*) :-No doubt there are as many different methods of starting a blast-furnace as there are men who assume that responsibility. Having blown-in a furnace a few years ago in a manner similar to that outlined by Mr. Sweetser, things went along so well at the start that I had time for a little reflection on what was going on inside the furnace. I saw the wood turned to charcoal practically, and it occurred to me, why should I use wood when I could put in the charcoal in the. first place, and thus save a lot of time, and also eliminate the dangerous gas from the wood, which is the cause of most of the accidents in starting up a furnace. I had a furnace out for repairs and decided to use no cord-wood in blowing in. I put in about a carload of charcoal and used no wood except some shavings and oily waste at each of the tuyeres. The furnace had 16 tuyeres and was 100 by 22 by 14.5 ft. Hot rods were put in each tuyere' and the blast started immediately at 11 a.m. Within 5 mill. the air was all driven out of the stack and the gas lighted of its own. accord at the top of the furnace. It was allowed to burn for 5 min. longer and then the bell was closed and the gas taken to the last stove and the last boiler on the gas-main. It was all clone so quietly that it was hard to realize that the gas was down. The tuyeres were as bright as if the furnace had been in blast for a long time. I have learned since that others have used the same method, but they had not passed the good advice along.

Jan 5, 1913

By E. P. Klier

The work of Klier and Lyman1 on the bainite reaction has led to the full description of this reaction for medium-carbon low-alloy steels. Certain experimental data reported by Klier and Lyman appear, however, to be improbable of obtaining in very high-carbon steels. The study herein reported consists of an analysis of the transformation characteristics of a 3 per cent chromium, I per cent carbon steel by means of X-ray and metallographic methods. From the results obtained it is concluded that the bainite reaction in this steel is more complicated than that reported by Klier and Lyman for the low-carbon low-alloy steels. Henever, the mechanism of bainite formation in this steel appears to be essentially the same as proposed for the low-carbon low-alloy steels with the modification that the first volumes to transform are carbon-rich rather than carbon-poor. Experimental Procedure The analysis of the steel studied was: Cr, 2.89; C, 1.02; Mn, 0.33; Si, o.35; S, 0.012; P, 0.020. The stock was received from the Carpenter Steel Co. in rolled bars. Specimen Preparation Specimens were austenitized at 1200°C. (2192°F.) for 25 min. in purified nitrogen. The resultant A.S.T.M. austenite grain size was 0-1. Isothermal transformation was allowed by quenching the specimens into liquid metal baths controlled to 5°C. at 540°C. (1004°F.) and above, and to 2°C. at 490°C. (914°f.) and below. Following the desired degree of transformation all specimens were water quenched. Metallographic Examination Specimens 1/4 in. round by 1/4 in. were used for nietallographic examination. Etch-ants used were Vilella's reagent (I gram picric acid, 10 ml. hydrochloric acid to make 100 ml. ethyl alcohol solution) and alkalinc sodium picratc (electrolytic). Vilella's reagent was effective in revealing all microconstitucnts, while the alkaline sodium picrate developed the carbon-rich structures or carbides only. X-ray Examination Two X-ray techniques were used—the Debye-Scherrer method and a back-reflection method. 'The small specimens necessary for the Debye-Scherrer method were austenitized and then allowed to transform, or were cut from the larger metallographic specimens. The metallographic specimens were used for the back-reflection X-ray analysis. When it was desirable to determine the structure of the carbide present, sliver specimens were electrolytically etched to develop a carbide coating, then were exposed in the cameras. This technique was frequently necessary to allow positive identification of the carbide.

Jan 1, 1945

By Lester W. Strock

METALLURGISTS handling lead and zinc ores have long been familiar with the spectrograph as a routine analytical tool, as its earliest regular use by American industry was in controlling impurities of zinc metal and its alloys. This application has been extended to other metal industries on an extensive scale, accompanied by refinements of procedure to such an extent that a large part of some metals produced, especially magnesium, aluminum and steel, are checked only by spectrographic methods for conformity to specifications. The spectrographic analysis of ores and other poorly conducting powdered solids presents difficulties not encountered with metallic samples, which can be arced or sparked as self-electrodes or can be readily dissolved, so that their solutions can be analyzed, as in the American Society for Testing Materials standard methods for zinc and zinc-base alloys. Spectra of powdered solid samples can be prepared by using carbon electrodes provided with a crater of suitable size, into which the sample is packed. Ore samples and many other powdered solid materials usually analyzed in the chemical and metallurgical laboratory are more complex and varied in composition than samples of metals produced in large tonnages. More preliminary work therefore is usually necessary in devising a spectrographic method for analyzing a given type of powdered sample than for analyzing metal samples, in order to use that method with confidence. The knowledge that the standard samples and unknowns produce equivalent line intensities at equal concentration is the fundamental basis of any quantitative spectrographic method. On the other hand, powdered samples have an advantage over metals in that any desired number of chemical compounds can be mixed dry in any desired ratio to produce a synthetic standard. Experience has shown, however, that spectra of elements in finely divided compounds introduced into a standard in preparing a synthetic ore sample do not always behave in the electric arc in a manner that produces spectral line intensities similar to those observed at the same concentration in a natural mineral. In ore samples minor elements frequently are contained in the crystal lattice of larger particles of an abundant ore mineral. Their dissociation and volatilization from the sample into the arc then proceeds differently in the standard and sample, with resultant differences in intensity. During the past 10 years I have devised and applied several quantitative spectrographic methods for determining various elements in rocks and minerals in connection with studies on their geochemistry,1 but the incentive has gradually changed since the summer of 1940 to the specific practical problem of searching for domestic sources of rare and strategic metals. The

Jan 1, 1945

By W. R. Phibbs

THE Columbia Steel Corporation, organized in 1922, and taken over by the United States Steel Corporation on Feb. l, 1930, is operating one blast furnace at Ironton, Utah, which was started on April 30, 1924, and is producing approximately 14,000 tons of pig iron per month. Half of the pig iron produced is basic iron and is used in its own plants at Pittsburg and Torrance, Cal. The ore for the blast furnace is shipped from Desert Mound, Utah, near Cedar City, in the southern part of the' State, approximately 231 miles from Iroaton. The ore is a hematite, disseminated with magnetite, the chemical analysis showing approximately 12 to 20 per cent magnetite, and under the micro- scope the ore has the appearance of a magnetite.

Jan 1, 1930

By Kenneth E. Kulp, Theodore Botinelly, George J. Neuerburg

Distribution of hypogene iron oxides may be useful in prospecting the Montezuma district, central Colorado, for certain metals, some of which have not been mined or sought in the district. The depletion of accessory magnetite in fresh rocks of the Montezuma stock identifies sources of ore minerals for the pneumatolytic metals, locates probable areas of possible contact-pneumatolytic deposits, and, in the altered rocks of the stock, identifies rock through which hydrothermal ore fluids have passed. Specularite veins are located in structures through which pneumatolytic ore fluids have passed and thus indicate optimal areas for prospecting. The presence of unusual amounts of vicarious metals such as bismuth, mercury, tin, and tungsten serves to identify magnetite and specularite that were involved in the pnematolytic ore process.

Jan 1, 1972