Search Documents

By L. B. Harris

Continuous cyclic unloading during tensile work hardening of polycrystalline zinc at room temperature enables specimens to sustain greatly increased extension. Such enhanced ductility is associated with creep-type extension, during which the cyclic component appears to promote relaxation of internal strains. It is possible to trace the transitions from tension, through enhanced cyclic extension, to fatigue and relate the observed behavior to simpler types of deformation. DISTINCTIVE deformation behavior has been shown to occur when loading includes both cyclic and unidirectional components. For aluminum and copper extended by a sequence of progressively biased strain reversals, coffin1 observed greater fracture ductility and lower flow stresses than during monotonic tension. This may be compared with the reduction in hardness obtained from conventional fatigue softening. But fatigue softening is accompanied by enhanced fatigue life,' whereas Benham3 found that fatigue life was reduced when copper continuously extended during axial load cycling. The corresponding specimen elongation, for large cyclic load amplitudes, was greater than during normal tension. Under different conditions, Bendler and wood4 found that torsional fatigue initiated extension in copper under low tensile loads previously in equilibrium with the specimen; fatigue life was again reduced. Thus there is a type of cyclic softening which is associated with reduced fatigue life and which occurs when the cyclic loading is accompanied by a unidirectional strain component. Further, the fracture ductility or extension obtained from the unidirectional component can exceed that obtained in the absence of cyclic load. Specimen extension was not initiated by axial fatigue at small load amplitudes;3 hence Benham's work distinguishes between fatigue at large and small amplitudes, the former often being linked with unidirectional deformation because of similarities in strain Structure. The initiation of tensile extension during torsional fatigue,4 however, occurred with small amplitudes. Comparable changes in behavior have been ob- served during creep. kennedy' found that combined cyclic and creep stresses on lead at 32°C increased the rate of elongation over that for simple creep, the consequence being a reduction in creep life. It was also demonstrated that small cyclic stresses applied after creep deformation initially increased recovery, but that prolonged application produced only normal fatigue hardening. It is clear that physical properties can be changed by interaction between the cyclic and unidirectional deformations, but owing to the number of different ways in which the deformations can be combined and the large number of possible variables for each combination, trends of behavior become easily obscured. One definite conclusion is that enhanced ductility or increased extension can be obtained by cyclic action, and it is this process that has been investigated for the tensile test by measurements of the extra tensile strain produced by the addition of a cyclic tensile component. EXPERIMENTAL PROCEDURE Material. Specimens were 99.99 pct Zn wire of 1.6 and 2.0 mm diam. Mean grain diameter was 0.02 mm, sufficiently small to give a ductile necked-down fracture under all loading conditions. All experiments were conducted at an average temperature of 20°C. Normal Tension. Unidirectional tensile curves at different strain rates were obtained from an In-stron testing machine, on which load-time curves were recorded autographically, using gage lengths of 5 and 10 cm. Straining was at constant cross-head velocity, and quoted strain rates are with reference to initial specimen length. Measurements of total elongation under simple tension were also made on the tensile machine that had been modified to incorporate an added fluctuating load. Combined Tension and Rapid Cyclic Load. An electromagnetic vibrator was coupled to the elastic beam of a Hounsfield ensometer- and driven sinus-oidally from a power amplifier at frequencies from 20 to 360 cps, the flexible connecting links on the tensometer being replaced by rigid fixtures to eliminate lateral vibration in the specimen. One end of the specimen was pulled by the normal extension drive of the tensometer while the other end, fixed to the elastic beam and vibrator, was subjected to rapid oscillations of load. It was thus possible to apply cyclic load to a tensile test without altering the rate of extension of the specimen

Jan 1, 1964

By E. R. Buchanan, R. E. Reed-Hill

Cylindrical magnesium single crystals were deformed in torsion. The axis of torsion was the basal pole. Five crystals were deformed to different strains between 0.08 and 1.03 and then sectioned in order to determine their dislocation densities using the transmission electron microscope. The work hardening rate of all specimens was at least an order of magnitude higher than that normally associated with easy glide in a tension test and comparable to that obserzed in stage B of a tension test. The correspondence between stage B in a tension test and the initial stages of a torsion test is believed to result from the fact that in both cases deformation occurs in a structure containing roughly equivalent densities of the dislocations associated with the three basal slip vectors. THERE are three basic ways of changing the shape of a crystal using slip dislocations. The crystal can be sheared along a slip direction in a slip plane; it can be bent about an axis in the slip plane normal to the slip direction; and, if the slip plane contains multiple slip directions, it can be twisted or rotated about the slip plane normal. Of the three processes, generally known as translational, flexural, and rotational slip, only rotational slip has not been extensively investigated. The object of the present research was to obtain basic information about this phase of crystalline plasticity. This paper is concerned with some aspects of the stress-strain curves obtained by twisting magnesium crystals about their basal poles. Magnesium was selected for four reasons. One, its recovery rate at room temperature is relatively low. Two, single crystals may be easily grown. Three, at room temperature the critical resolved shear stress for basal slip is about two orders of magnitude lower than that for nonbasal slip, so that rotational slip might be expected to occur primarily by basal slip. Finally, relationships between flow stress, shear strain, and dislocation density have been determined for tensile deformation of magnesium crystals,' thereby providing a basis of comparison for the torsional results. EXPERIMENTAL PROCEDURES Crystals were grown from 0.5 in. diam extruded sublimed magnesium rod furnished by the Dow Chemical Co. who reported that it contained in weight percent less than 0.0003 Al, 0.01 Ca, 0.01 Cu, 0.0012 Fe, 0.001 Mn, 0.0005 Ni, 0.003 Pb, 0.001 Si, 0.01 Sn, and 0.02 Zn, with the balance magnesium. All crystals were grown in a dried argon atmosphere using Jill-son's2 modified Bridgman technique. Two different methods were used to obtain crystals with the basal plane normal to the specimen axis. These included direct growth from seeds of the proper orientation, and spark machining (trepanning) of 0.5 in. diam cylinders from larger (1.5 in. diam) randomly grown crystals. The crystals thus produced were polished in a 20 pct HC1 water solution and then etched in a 1 pct HC1 water solution to develop etch pits lying in rows parallel to the basal plane trace. The crystals were then revolved about their axes on the stage of a low-powered microscope. Torsion specimens were prepared only from those crystals whose axes were normal to the rows of etch pits. It is estimated that this simple orientation method was accurate to about 51 deg. 1.625 in. long cylinders were next cut from these selected crystals and then acid machined in a 20 pct HC1 water solution into torsion specimens with a 1 in. long by 0.30 in. diam reduced gage section. Following this, they were annealed in air at 400°C and furnace cooled to room temperature. The specimens were given a final polish in a 10 pct HC1 water solution, rinsed in ethanol, dried, and cemented into brass grips with an epoxy resin. In addition to the torsion specimens, several tensile specimens with their basal planes at 45 deg to the stress axis were also prepared with similar dimensions except that the gage sections were increased to 4 in. in length. The torsion specimens were tested in the apparatus

Jan 1, 1970

By S. A. Hovanessian

Analytical solutions are obtained for calculating the pressure distribution in rectangular fields due to injection and/or producing wells located anywhere within the field. The field is assumed to be homogeneous with either constant pressure or no-flow boundaries. These solutions are extended to include the calculation of average reservoir pressure and permeability from pressure build-up curves. Numerical examples are given to illustrate the application of equations to practical problems. INTRODUCTION Pressure distribution analyses are of considerable importance in the field of reservoir mechanics. A number of papers dealing with this subject have appeared in the petroleum literature. perrinel in 1956 presented a summary of the methods available for pressure build-up calculations and discussed the applicability of each in some detail. More recently (1958), Hazebroek, et a1,2 discussed a theoretical method for obtaining pressure distribution in a radial field. Also in 1958, Nisle3 gave a theoretical solution of the pressure distribution in a field extending to infinity with a partially penetrating line source at the origin. Mathews, et a1,4 applied the method of images to existing solutions for pressure distribution in radial fields and obtained expressions for calculating pressures in bounded reservoirs. However, a literature survey revealed that a general analytical solution for the pressure distribution in a rectangular field, with injection and/or production wells located anywhere within the field, was not available. Such a solution could be used to approximate the pressure distribution in a field the shape of which is nearly rectangular. Furthermore, it could be applied to pressure calculations pertaining to a single well taken from a system of wells which were drilled in a rectangular pattern. In this case the boundaries of the well drainage area are considered to be the perpendicular bisectors of the lines joining the well and its nearest neighbors. The basic problem considered in this paper consists of a rectangular field with either constant-pressure 01 no-flow boundaries and with either an injection or production well located anywhere within the field. The physical properties of the rock and fluids present are considered to be constant. Analytical expressions are obtained for the pressure distribution within the field during the production or injection periods. These expressions, which are infinite series, can be used to evaluate pressure at any point within the field as a function of time and position. For fields containing more than one well (production and/or injection), the solutions for each well acting independently are superposed. That is, at any point in the field, the pressures due to each injection 01. production well acting alone can be algebraically added to give the pressure resulting from all wells acting simultaneously. Evaluation of the series solutions given in this paper is readily accomplished by means of an electronic digital computer; and, in most cases, sufficient accuracy is obtained by setting the upper limits of summation at 20. These solutions are extended to include the calculation of average reservoir pressure and permeability from build-up data. A number of numerical examples are given to illustrate application of the solutions to actual field problems. ANALYTICAL SOLUTIONS The partial differential equation representing the pressure distribution in a homogeneous rectangular field (see Fig. I.), having a single source or sink of strength (2, can be written*

By John W. Cahn

Tile avevage value of the mean curvature of surfaces in a specimen can be precisely delermined by sitrlple measurements performed on random sections or on 1 vojectiotzs of these surfaces. For surjaces enclosing particles, the quanlity is sllown to be velated to the probable tlurrrhev ot particles intevcepted by a random platne and, under certain conditions, to the perimeter of their Projected image and to the increuse in surjace area when the particles grow. Many of the velalionsl~ips are valid for any shape or size of the particles. THE recent growth of the field of stereology or quantitative microscopy is largely the result of the discovery of a limited number of rigorously defined geometrical parameters that can be precisely measured on random sections or projections of a structure without assumption about particle shape.' Such parameters have been the volume fraction and surface area and line length in a unit volume. The present paper introduces the average of the mean curvature of surfaces in a volume, and shows that it can be rigorously measured by counting methods alone. AVERAGE CURVATURE ON A PLANE Consider a curve y = v (x) on the xy plane. The curvature Kp in the plane at any point is given by Kp = (dZy/dx2)/[1 + (dy/dx)2]3/2. The average curvature along the curve may be defined as Kp = (1/L) fKpdl |1] where dl = [(dx)' + {dy)2]1/2 is the length of an element of the curve and .(dl = L is the total length of the curve. The integral on the right-hand side of Eq. [l] will be called the total curvature, It is dimensionless and readily evaluated by substituting d = arctan (dy/dx) to give ah which is the change in direction of the tangents to the ends of the curve, Fig. 1. Hence, Kp = (1/L)(?h) [2] It can also be seen that Eq. [2] is applicable in the limit of sharp corners. Even though the curvature is infinite at a corner, f Kpdl remains integrable and equal to the change of angle. The signs of the quantities Kp and dl are arbitrary and, if the areas adjoining the curve are equivalent, there seems to be no compelling reason to fix the signs. For a closed curve, however, it becomes worthwhile to use the signs to distinguish among different types of areas or phases enclosed. For such a closed curve AO = t2r and As a convention, we shall take the direction of the integration along the curve in such a way that the area or phase under consideration (henceforth called a) is kept to the left side of the curve, Fig. 1. Then Kp is positive where the curve is concave and negative where the curve is convex. For a closed curve Ad - +2n if the curve encloses a, and Ad = —2n if the curve is surrounded by a. PLANAR SECTIONS OF THREE-DIMENSIONAL STRUCTURE OF ISOLATED a PARTICLES Consider next a planar section of a microstructure containing particles of a in a matrix. We place no restriction on shape of connectedness of these particles, and begin by considering the curvature of only the boundary between a particles and matrix' Clumps of contiguous a particles are then treated as a single a particle. The two-dimensional section will show in a unit area na simple closed curves enclosing a particles and nh closed curves of holes, in-

Jan 1, 1968

By Ralph W. M. Lai, D. W. Fuerstenau

This paper presents the results of a study of the principles which control the distribution of ultrafine particles between an oil phase and an aqueous phase. Alkyl sulfonates were used to control the wettability of fine alumina particles and to stabilize the water-isooctane emulsion system in the extraction process. The effects of sulfonate chain length, sulfonate adsorption, pH, and oil-water ratio on the recovery of solids in the oil phase were investigated. Higher extraction was found under conditions which yield higher hydrophobicity and large interfacial area of the oil-water emulsion. Today there is considerable interest in developing methods for the recovery of fine particles from disseminated ores. One such method might be the extraction of fine particulate solids from aqueous suspensions into an oil phase, and one example of a successful industrial process based on oil-water distribution phenomena is the emulsion flotation process used in concentrating manganese ore.' The oil agglomeration process of Farnand, Smith, and Puddington has been suggested for concentrating tin ore. Patents 3-4 for oil flotation processes extend back to that of William Haynes in 1860. The basis of all these processes is directly related to the stabilization of emulsions with solid particles. The first extensive study of oil-water emulsions stabilized by finely divided solids was made by Pickering. Later, Briggs,6 weston, 7 Chessman and King,8 and Leja and Schulman9 experimentally demonstrated how solid particles control water-oil and oil-water systems. Hildebrand10 suggested that fine particles can stabilize an emulsion because the fine particles are partially wettable by both oil and water, that is, that the contact angle must be finite. Takakuwa and Takamori 11 recently applied emulsion inversion to the study of collector adsorption in flotation systems. At the Royal School of Mines, Shergold and Mellgren12 are currently carrying out a comprehensive study of the extraction of fine particles into an organic liquid phase. In the present study of the liquid extraction or oil flotation of ultrafine particles, the recovery of hydro-philic alumina particles of 0.1-µ average diameter was determined after separating an isooctane-water mixture (emulsion) into its two phases. Alkyl sulfonates of different chain lengths were used to change the wettability of the alumina and to effect emulsifi-cation of the oil-water mixture. The effects of the oil-water volume ratio, sulfonate adsorption, and pH on the recovery of the fine particles were investigated. Since the surface charge on an oxide such as alumina is determined by the adsorption or interaction of H+ and OH- with the surface, pH control is extremely important. Furthermore, since the zero point of charge (zpc) of alumina13-14 occurs at pH 9 to 9.4, major adsorption effects with anionic collectors in these systems will occur below pH 9. The results of the foregoing investigation are discussed in terms of the recovery of the fine particles, the oil-water ratio, contact angles, surface tension, the adsorption of sulfonate onto the solid surface, and the emulsifica-tion of oil. MATERIALS AND EXPERIMENTAL METHODS Materials: The particulate solid used in all the experiments was Linde "A" alumina, a high-purity, readily available form of a-alumina. The surface area of the alumina, as evaluated from measurements of stearic acid adsorption from benzene, was 14.5 sq m per gm, based on a value of 20.5 sq Å for the cross-sectional area of stearic acid.13 All aqueous solutions were prepared from triply distilled conductivity water. Other materials included high-purity crystals of sodium alkyl sulfonates, isooctane, and, for pH adjustments, reagent grade hydrochloric acid and sodium hydroxide-Because sulfonic acids are strong acids, they are

Jan 1, 1969

By R. J. Sandrea, S. M. Farouq Ali

The results of an experimental and theoretical study of the effects of rectilinear impermeable barriers and highly permeable channels on the sweep efficiency and conductivity of a five-spot network are presented. The study was carried out using Hele-Shaw, and conductive sheet analogs for both. normal and inverted flood patterns. A functional relationship was developed which provides quantitative prediction of the above parameters; i.e., sweep efficiency and conductivity, for the nonhomogeneous system. To evaluate this, it is necessary only to measure the interference modulus of the obstacle using a simple expression. The results indicate that impermeable barriers, with an interference modulus greater than zero, always cause a decrease in the conductivity and the sweep efficiency of the pattern. On the other hand, permeability channels do not have a significant effect on these parameters, unless they are located along the streamlines. The study also discusses a method of formulating the difference equations pertaining to the two-dimensional Laplacian in a system containing rectilinear barriers. In addition, a technique is described for tracing the progress of a free surface, using marked particles, in a stream containing discontinuities SuCh as those occurring at the extremities of barriers. The above computational scheme was used in a digital computer program to simulate results of the Hele-Shaw analog. The computed values of sweep efficiency mere in good agreement with the experimental values. INTRODUCTION At the present time waterflooding remains the most widely used technique for the secondary recovery of oil. Among the numerous factors that affect the performance of a waterflood, the areal sweep efficiency constitutes one of the most critical parameters. It is a function only of the geometric distribution of the wells for a homogeneous medium and unit mobility ratio. Geological considerations, however, such as the presence of sealing faults or solution channels in the rock matrix, would generally exert an adverse effect on the areal sweep efficiency of a waterflood network. Surprisingly little information is presently available on the quantitative implications of such permeability interferences. It was the object of this investigation to consider the presence of rectilinear, impermeable and highly permeable interferences in an otherwise homogeneous five-spot pattern, and to analyze their effects on the resulting sweep efficiency and pattern conductivity. The experimental phase of the study was conducted using two different models: the Hele-Shaw flow cell and the field plotter. For experimental convenience, the geometric boundaries of the five-spot were assumed to constitute streamlines even in the case where the interference was asymmetrically placed with respect to a repeated five-spot pattern. A second object of the study was to develop a computational scheme for numerically calculating the pressure distribution in a five-spot flow pattern containing rectilinear, impermeable barriers, and to use this distribution to compute the sweep efficiency. EXPERIMENTAL PROCEDURE HELE-SHAW ANALOG The Hele-Shaw analog was used both as a visual model and for determining the sweep efficiency for systems involving impermeable barriers. The physical limitations of this model as a means of experimentally studying the motion of a fluid in porous medium have been adequately discussed elsewhere.2,7 Likewise, it can be easily verified that the analogy remains valid when a portion of the region between the plates contains an obstacle of the same thickness as the distance between the plates. The model used in this study was composed of

By S. E. Bronisz, J. O. Brittain

Experiments have been carried out to study the effect of an applied stress on strain aging in steel. It was found that the stress-induced strain aging reaction proceeds rapidly in the temperature range of 0° to 60°C. The variation of stress-induced strain aging with plastic strain, aging time, and temperatures is reported. The activation energy for the stress-induced strain aging was found to be 10,000 cal per mol for the steel used in this investigation. VARIOUS observations1-5 have been made of the influence of an applied stress upon the yielding of iron and steel. However, there have been only cursory studies of the effect of an applied tensile stress upon strain aging in iron and steel1,2 The following represents the results of a preliminary study of strain aging as influenced by the application of an external tensile load during the aging process. For the most part, previous experimental work on strain aging can be classified into two parts. First, the experimental technique involved a direct determination of mechanical properties of a suitable specimen that has been plastically deformed to a constant strain and aged generally at a temperature of the order of 200°C, with the aging times varying from about 1/10 to 2 hr.6-8 The second classification of strain aging experiments involves an indirect determination of strain aging by means of physical property such as electrical resistivity or internal friction as a function of the aging time at a constant temperature and strain.9-12 The latter results have

Jan 1, 1961

By D. E. Peacock, B. Harris

Thermal-expansion and electrical-resistivity measurements have been carried out below 400°K on niobium and two niobium alloys containing tungsten. For anonaly in the expansion us temperature curve below aboct 300°K. This reslt is consistent with an earlier obsercation that Young's modilus joy Cb-132 lms an unusiully strong -tenperati-e dependence below roon temperature. No anonulous behavior was observed in the resistiuity vs temperature curve for either alloy or in the magnetic susceptibility us tenperature curve for Cb-132. These results are disclssed in terms of various electronic and bonding theories of the transition metals and their alloys, but it has not been possible to reach any definite conclusion as to the cause of the results obtained. ALONG with investigations of the low-temperature mechanical behavior of niobium and its alloys, some of the physical properties of these materials have also been studied. In the work described here, thermal expansion and electrical resistivity were measured below 400°K for niobium and two of its alloys, Cb-132 and D-43. In addition, the magnetic susceptibility of Cb-132 was measured over the same temperature range. The alloys are representative of two distinct tion-hardened alloy such as might find service as a turbine blade, while D-43 (Nb, 5.3 at. pct W, 1.1 at. pct Zr. and 0.08 at. pct C) is a solution- and dispersion-hardened alloy, of considerably lower strength than Cb-132. which is a potential vane material. Their significant common feature is the presence of tungsten as the principal source of solution hardening. EXPERIMENTAL TECHNIQUES Thermal-expansion measurements were made with a quartz-tube dilatometer using baths of liquid nitrogen, liquid bromoethane, and a liquid polyalkylene glycol derivative to cover the range 80 to 400 K. Results are recorded as expansion relative to that of quartz, and the probable maximum error in any value of relative expansion. All, is about il pct. The metallurgical condition of the specimens, which were in rod form. will be discussed in the section dealing with experimental results. Resistivity was measured on recrystallized wires 0.030 in. in diam using a potentiometric technique. The same baths were used for temperatures between 80' and 400°K as were used for the expansion measurements. and in addition the resistance of D-43 and Cb-132 was measured at 4.2 K by immersion in liquid helium. The maximum expected experimental error in any resistivity value is about 3 pct and that in any change in resistivity about i0.05 pct. Temperatures in both sets of experiments were measured with liquid-in-glass thermometers with an accuracy usually better than 1°K. EXPERIMENTAL RESULTS 1) Thermal Expansion. In Fig. 1 is shown the relative linear expansion of recrystallized niobium. D-43. and Cb-132. The curve for Cb-132 is composed of results from several runs on three different samples. Two of the samples were annealed for an hour at 1500°C to cause recrystallization and the third was annealed for an hour at 2000'C to remove some mi-crosegregation of tungsten which was known to be present in the wrought alloy received from the manu-

Jan 1, 1967

By L. L. Handy

The most common method of identifying hydrocarbon-bearing strata in a well that penetrates many different formations involves measurement and interpretation of the electrical properties of the formations as determined by electrical logs. Even though this method is used extensively, and even though in a great many instances it is capable of indicating presence of oil or gas, situations arise for which it is extremely difficult, if not impossible, to deduce the presence of hydrocarbons. These situations may involve the following. 1. A thin formation, bounded by highly resistive formations, in which it is impossible to obtain the actual resistivity of the uninvaded zone with existing logging devices. 2. A formation in which invasion has been so extensive that a value for the uninvaded zone resistivity cannot be obtained. 3. A very shaly formation in which the resistivity index, I, is lower than that usually associated with productive formations. 4. Laminated formations comprised of thin productive sands separated by thin shale streaks in which the individual sand and shale streaks are too thin to permit measurement of uninvaded-zone resistivity with existing logging devices. 5. Productive formations in which the water saturation is high. To extend the utility of electric log interpretation to identification of hydrocarbons in all types of formations, there is strong incentive to find a method not subject to these limitations. Some time ago, in connection with research on the wettability of reservoir rock, an investigation was conducted in which the resistivities of cores were measured shortly after they were removed from a core barrel, and again after they had been extracted and restored to their original oil and brine saturation.' The resistivities after extraction were generally lower. Other tests made on the cores indicated that they were more nearly water wet after they were extracted; thus, it was assumed that the observed changes in resistivities were due to a change in wettability of the cores. Other experiments'," have shown that resistivities of rock samples are sharply dependent on wettability. These experiments have shown that oil-wet samples are more resistive than water-wet samples. To obtain an understanding of how the wetting properties of the surfaces of core material affect electrical resistivity, a series of experiments was conducted. Two groups of core samples were prepared for testing. One group contained brine, but no residual oil. The other group was saturated with brine, flooded with oil to a low water saturation, then flooded with brine to a final residual oil saturation. Resistivity measurements were made on each group. Both groups were then flooded with the original brine to which a chemical had been added that renders sand and clay surfaces preferentially oil wet, a so-called reverse-wetting agent. very little change in resistivity was observed in cores containing only water. The group containing residual oil, however, showed resistivity increases of 100 to 200 per cent. These experiments showed that the resistivity of a core containing oil could be altered by changing wet-tability of the core. Moreover, the possibility was introduced that reverse-wetting agents might be employed as the basis for a logging method for identification of oil-bearing strata. Since behavior of a porous rock containing gas and water might be expected to be similar to that of a rock containing oil and water, such a method should also be applicable to identification of gas-bearing zones. In principle the wettability of the invaded zone could be reversed without altering conductivity of the interstitial water or the hydrocarbon saturation therein. Those strata showing significantly increased invaded-zone resistivities would, therefore, contain hydrocarbons; those with no significant change would be filled only with water. Addition of a reverse-wetting agent to a hydro carbon -bearing zone which is, by nature, already preferentially oil wet would not result in an enhancement of its resistivity. It is generally believed, however, that most hydrocarbon-bearing strata are preferentially water wet.

By Francis R. Conley, John A. Sievert, John N. Dew

A brief review is presented of the past performance of a number of large, thin, highly permeable reservoirs with low dips in the Bolivar Coastal fields of Venezuela. The performance of these reservoirs indicates that the fluids are segregated vertically within the sand section by gravity. With this assumption, equations are developed which describe the performance under pressure maintenance operations. Methods of solving these equations and results of simple example calculations are presented. Example calculations indicate that under pressure maintenance conditions injected gas tends to {tow preferentially along the top of the sands and that encroaching water has a tendency to flow preferentially along the bottom. The expected performance of segregated fluids is discussed and compared with that of fluids which are uniformly distributed in any sand section. INTRODUCTION The field performance of a number of reservoirs described herein indicates that the fluids are segregated vertically within the sand section by the force of gravity. Thus, it was felt that any method used to predict the future performance of these reservoirs should consider the effects of segregation in the sand sections. A study of the available information on some of the reservoirs suggests that increased recoveries may be expected if the reservoir pressure is maintained by either crestal gas injection or flank water injection. To predict future performance of reservoirs under pressure maintenance operations, a method of analysis was needed which would account for segregation of fluids in the sand sections. Several methods of analysis have been developed to take into account the segregation of fluids in the reservoir as a whole1,3 To our knowledge no method considers segregation of the fluids within sand sections in the manner indicated by the past performance of several reservoirs in the Mara-caibo Basin. This paper outlines part of the work done in studying some of these reservoirs and contains a description of their performance characteristics. The analysis presented is restricted to pressure maintenance conditions, since space limitations prevent a full discus- sion of the development of the mathematical relations and the various methods of solving them. Only a sketch of the development of the mathematical relations is given. The various methods of solving these relations are pointed out, but the actual determination of solutions to various problems are omitted except for one example. It is felt that these results may aid in the study of reservoirs outside the Maracaibo Basin. Some concepts on which the present analysis is based are outlined by D. N. Dietz. However, the analysis presented herein includes several factors not considered by Dietz: (1) variations in permeability and in the cross section, (2) various shapes of the cross section, and (3) the production of fluids. Also, the mathematical development presented by Dietz differs considerably from our corresponding analysis. RESERVOIR CHARACTERISTICS The reservoirs under consideration, large and thin, with low dip and high permeability, are large to the extent that they contain from 0.5 to over four billion bbl of oil initially in place. The section thicknesses vary from 100 to 400 ft and the lengths from 10,000 to 40,000 ft. Thus, a length-wise cross section of the producing formation appears to be long and thin. The dip angles vary from 0 to 6 degrees and the average permeabilities vary from 0.5 to over three darcies. The reservoirs contain from 20 to 50 per cent shale inter-laminated with the productive sands. Most shale breaks within the major sands do not correlate from one well to the next, and correlation is often difficult, even between wells drilled from the same location. However, it is often possible to correlate the shale breaks between major sands for some distance. Herein we are concerned with the performance of reservoirs containing oil of gravities over 20" API. Past reservoir performance indicates good pressure communication and, in cases where pressure sinks have developed, large amounts of fluid migration have occurred. Few of the reservoirs have had initial gas caps, but also, few have been found to be highly under-saturated. Due to gravity segregation, secondary gas caps usually form before the pressure has been reduced more than 25 per cent of its initial value. The effect of gravity has not only been apparent on a reservoir-wide basis, but has also caused segregation of the reservoir fluids in productive sections. Proof of this is found from the results of selective well tests, workovers, and electric and various other types of logs. Evidence that

By H. W. Reinhardt, J. W. Dally

A dynamic photoelastic analysis of stress waves interacting with a free surface is described. The free surface is that of a bench with a fixed bottom so common in quarry applications. The stress waves are generated by line charges of lead azide (Pb N,). Four models of identical geometry are investigated with the direction of detonation of the line charge varied between the four models. Dynamic photoelastic patterns are recorded and analyzed to indicate which method of detonating the line charge produced the largest magnitude of tension at the free surface. The mechanics of rock breakage by means of explosives has received considerable treatment by many investigators including Duvall, Obert, Broberg, Rinehart, and Langefors1-11 over the past two decades. Indeed in more recent years several texts12-15 have been written on the topic, treating a wide variety of subjects which are logically related to the modern technique of rock blasting. In rock blasting the chemical energy of a concentrated explosive contained in a relatively small diameter borehole is utilized to fragment the rock. The explosive is transformed into a gas with enormous pressures which exceed 10-5 bars18 This high pressure shatters the rock in the area adjacent to the borehole and produces dilatational and distortional stress waves which propagate radially away from the borehole. The state of stress associated with these outgoing waves produces a system of cracks which extend for a few feet from the borehole. The breakage produced in this manner is limited as the dynamic stress in the pulse attenuates markedly with distance. In the absence of a free surface, the stress wave propagates away from the source without further fracture. With a free face of rock near the drill hole, another mode of breakage occurs which is due to scabbing failure of the layer of rock adjacent to the free face. These scabbing failures are produced by the reflection of the incident waves and the conversion of compressive stresses into tensile stresses sufficiently large to fracture the rock. The detailed nature of the interaction of the stress waves with the free surface is complex and difficult to treat analytically. However, dynamic photoelasticity offers an experimental approach which gives a fullfield visual display of propagating stress waves and the reflection process. Applications of static photoelasticity to solution of problems related to mining technology have become relatively common (see, for instance, Refs. 17 and 18) with a plastic model loaded to produce a state of stress representative of that occurring in the workings of a mine. The application of dynamic photoelasticity is ex tremely limited. Tandanand and Hartman19 have used a multiple spark camera to study fracture in glass and plastic plates impacted by a chisel-shaped tool. This paper describes a dynamic photoelastic analysis of stress waves interacting with a free surface. The free surface is that of a bench with a fixed bottom so common in quarry applications. The stress waves are generated by line charges of lead azide (Pb-N6). Four models of identical geometry are investigated with the direction of detonation of the line charge varied between the four models. Dynamic photoelastic patterns are recorded and analyzed to indicate which method of detonating the line charge produced the largest magnitude of tension at the free surface. Experimental Procedure The model illustrated in [Fig. 1] was fabricated from a sheet of Columbia Resin CR-39 to represent a bench with a fixed bottom. Properties of the CR-39 pertaining to these dynamic experiments are listed in [Table 1]. Scribe lines on 1-in. centers are used to identify locations along the bench face. The bench height was 8 in., the burden was 3 in., and the overall dimensions of the sheet, 16 and 18 in., were large enough to eliminate reflections from nonessential boundaries during the period of observation of the dynamic event. To simulate a charge in a borehole, a groove 0.062 in. wide and 0.080 in. deep groove was cut into the sheet from one side. The lower end of the groove was 1 in. or 1/3 the burden distance below the bottom of the bench. The upper end of the groove was 3 in. or one times the burden distance below the upper level of the bench. The groove was packed with 60 mg of Pb No per in. of length, and ignited with a bridge wire detonator. Four different ignition procedures were used to examine the effects of detonation direction on the stress wave interaction with the free face of the bench. In Test 1 the line charge was ignited at the top and the line charge detonated downward. In Test 2 the line charge was ignited at the bottom and the charge burned upward. In Test 3 the charge was ignited in the center with the top half burning upward and the bottom half burning downward. Finally in Test 4 the line charge was ignited at both ends simultaneously. Sixteen high-speed photographs of the photoelastic fringe patterns representing the stress wave propagation were recorded for each of the tests. A Cranz-Schardin multiple spark gap camera 20,21 was operated at framing rates which were systematically varied from 110,000 to 250,000 frames per sec during each test.

Jan 1, 1972

By G. H. F. Gardner

The velocity and attenuation of elastic waves in sandstones were measured as a function of both pressure and fluid saturation. A large change occurs in these quantities if water is added and the rock is not compressed, but the change is small if the rock is subjected to a large overburden pressure. Measurements were made by vibrating cylindrical samples in both the extensional and torsional modes at frequencies up to 30,000 cycles/sec. Formulas were derived which enable the attenuation of dilatational waves in dry rocks to be deduced from the data. Similar experimental methods were used to investigate the properties of unconsolidated sands. Velocities were found to vary with the 1/4 power of the overburden pressure and attenuations to decrease with the 1/6 power. The effects of grain size, amplitude and fluid saturation were studied. Formulas by which the effects produced by a jacket around the sample may be calculated were derived. The practical application of these results to formation valuation is discussed. INTRODUCTION The attenuation of elastic waves in the earth has been of interest to the seismologist and geophysicist for many years, but only recently to the petroleum engineer. Engineering interest has been brought about by the success of velocity logging devices, for it is possible by modification of these instruments to measure the attenuation of sound waves in addition to their velocity and, hence, deduce the mobility of formation fluids as well as the porosities of the rocks which contain them. The main problem is to decide whether field measurements can be made with sufficient accuracy to be of practical use. This problem can only be solved after we know the magnitude of the attenuations which are typical of the earth at various depths. The logarithmic decrement of a fluid-saturated rock is the sum of a "sloshing" decrement and a "jostling" decrement, the former caused by the mobility of the fluid contained within the rock and the latter by the granular framework of the rock. Sloshing decrements can be calculated' using Biot's theory, but the jostling losses are less well understood. The present paper reports an experimental investigation of jostling losses in consolidated and uncon- solidated sands, particularly with respect to the effect of overburden pressure and fluid saturation. Born' showed that the decrement of a sandstone may increase dramatically when only a few per cent by weight of distilled water is added, and that the additional loss is proportional to the frequency of vibration. His measurements were made with no compressive stress on the framework of the rock. M. Gondouin3 investigated similar phenomena for fluid-saturated plasters but also did not compress the samples. In the present paper it is shown that compression of the framework reduces this effect, so that at depth the jostling decrement of a sandstone may be expected to be almost independent of fluid saturation and frequency. Decrements for many sedimentary rocks have been given by Volarovich,4 but all for the state of zero overburden pressure. Anomalously low velocities have been logged in shallow unconsolidated gas sands. Results of the present investigation confirm that these velocities are not caused by correspondingly high attenuations, because the jostling decrement in a packing of sand grains is small and much less than in a consolidated sandstone at the same depth. Velocities in sands have been measured by Tsareva5 and by Hardin6 as a function of pressure, but the corresponding decrements do not appear to have been measured previously. The widely used "resonant bar method" of measuring velocities and decrements was employed. Comments on variations of this technique have recently been published by McSkimmin.7 The main novelty of the present technique was the application of pressure to the samples. It was found possible to do this by placing the apparatus inside a pressure vessel, provided the conditions leading to large additional losses were avoided. These conditions are discussed below. EXPERIMENTAL TECHNIQUE Cylindrical samples were caused to vibrate in both the extensional and torsional mode of vibration and the amplitude of vibration was measured as a function of frequency in the neighborhood of a resonant frequency. The resonant frequency, fr, is related to the corresponding elastic modulus by the formulas where E and N are Young's modulus and the modulus of rigidity, p is the density of the sample, and A the wavelength of the vibration.

Jan 1, 1965

By J. S. Levine, M. Prats

A homogeneous and uniform cylindrical reservoir containing oil and gas is fractured vertically on completion and is produced at a constant bottom-hole pressure. The fracture has an infinite flow capacity, is of limited lateral extent and is bounded above and below by the impermeable strata defining the vertical extent of the reservoir. Results show that such a fractured reservoir can be represented by a reservoir of circular symmetry having very nearly the same production history. The well radius of this circular reservoir is about 1/4 the fracture length and is essentially the same as that obtained previously for a single fluid of constant compressibility. At the same value of cumulative oil production, gas-oil ratios of fractured reservoirs producing at constant terzinal pressure are larger than those of reservoirs having no fractures. This leads to more inefficient use of the reservoir energy in fractured wells and results in lower reservoir pressures for the same cumulative oil production. The reduction in operating life due to fracturing a reservoir is not as great as that for a slightly compressible fluid. This diflerence can be accounted for by the lower reservoir pressure in the fractured reservoir and its adverse effect on the average mobility and compressibility of the oil. As anticipated, the reduction in operating life increases czs the reservoir permeability decreases. The type of results presented in this report can be used to determine the economic attractiveness of fracture treatments per se, to setect the initial spacing to be used in developing a field, and to compare the relative merits of fracturing available wells and infill drilling. INTRODUCTION The effect of vertical fractures on a reservoir producing either an incompressible or a compressible liquid has already been discussed in the 1iterature.l,2 Those results indicate that the production history of such a reservoir is essentially the same as that of a circular reservoir having an effective well radius of approximately one-fourth the fracture length. The present work reports on the effect of a vertical fracture on a reservoir producing two compressible fluids —oil and gas—by solution gas drive. Because of the empirical nature of the PVT and relative permeability data used to obtain the performance of such reservoirs, results can only be obtained numerically and with the aid of high-speed computers. Since reservoirs lose their radial symmetry when fractured vertically, pressure and saturation can no longer be given only in terms of distance from the well. Two coordinates (such as x and y) must now be used to describe the pressure and saturation within the reservoir, and, since we are dealing with compressible fluids, time is also a variable. Thus the solution of a vertically fractured reservoir requires finding two unknowns (pressure and saturation) in two space variables (say x and y) and in time (t). Since no means are readily and generally available for solving such problems at the present time, we have used the results of previous work1,2 to approximate the effect of a vertical fracture on a reservoir producing both oil and gas by depletion. The purpose of the present wmk, then, is to investigate the possibility of using available numerical techniques (limited at the moment to one space variable) to study the two-space-variable flow behavior resulting from a vertical fracture. Results obtained in the course of this investigation are also reported and discussed. Input and output data of the numerical methods used are given in practical units: BOPD, feet, psi, cp, and md. Results are discussed fist in terms of specific reservoir and crude properties and geometries. Later, dimensionless parameters are introduced in order to extend results to different values of some of the reservoir and fracture properties. IDEALIZATION AND DESCRIPTION OF THE FRACTURED SYSTEM It is assumed that a horizontal oil-producing layer of constant thickness and of uniform porosity and permeability is bounded above and below by impermeable strata. The reservoir has an impermeable, circular, cylindrical outer boundary of radius r,. The fracture system is represented by a single, plane, vertical fracture of limited radial extent, bounded by the impermeable matrix above and below' the producing layer (reservoir). It is assumed that there is no pressure drop in the fracture due to fluid flow. 1 indicates the general three-dimensional geometry of the fractured reservoir. Gravity effects and the effects of differential depletion resulting from variations in hydrostatic head (pressure) will be neglected. Thus, the flow behavior in the fractured reservoir is described by the

By L. W. Pommier, F. B. Brien

The Rheological properties of pulps are non-Newtonian in character and more than one viscosity parameter is necessary to describe their behavior, therefore, the single term 'apparent viscosity' which has been used in the past may be misleading. The study reported in this paper uses a dimensional analysis based on the Ostwald-de Waele shear stress-rate of shear model for non-Newtonian liquids to develop velocity and resistance equations for falling spheres. An electronic monitoring apparatus was assembled for determining the velocity of metallic bodies as they fall through opaque liquids and suspensions. By means of this apparatus the behavior of the viscosity parameters of the Ostwald-de Waele model and the applicability of the proposed equations were examined for a number of non-Newtonian liquids. The validity of the equations for these liquids was confirmed. Preliminary data collected using solid-liquid suspensions established the validity of the form of the basic equations for these systems. The differential movement of solid particles through solid-liquid pulps and suspensions is very important LO many branches of engineering, such as minerals processing, soil mechanics, ceramic slip processing, oil well drilling-mud technology, materials-handling in pipelines, and many others. There is a dearth of fundamental knowledge on the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. The resistance offered by Newtonian liquids to the movement of free settling spheres is well described for laminar and turbulent conditions by Stokes' and Newton's Laws, respectively. However, problems are encountered when attempts are made to extrapolate these simple relationships into solid liquid suspensions. The rheological properties of pulps are such that they are non-Newtonian in character;'" that is, the applied shearing stress and resulting rate-of-shear are related by non-linear functions, and thus, in the simplest case two viscosity parameters are necessary to describe their rheological properties. For this reason the single term 'apparent viscosity' which has been commonly used to explain the flow resistance of suspensions and non-Newtonian liquids may be misleading. It is realized that a rigorous analysis of the rnechanisms of momentum transport of liquid-solid systems is complex indeed. There are many variables that affect the rheological properties of the systems such as density, size, shape, and surface energy of the suspended solid and density and viscosity of suspending liquid, as well as the solid to liquid ratio. However, it was felt that a useful contribution to the knowledge of the behavior of suspensions could be made by examining the systems in terms of the basic fundamentals of nowNewtonian flow. This has led to the development, by means of dimensional analysis, of velocity and resistance equations, using two viscosity parameters to describe the velocity of penetrating bodies and the flow resistance encountered by these bodies, as they pass through non-Newtonian systems. THEORY In order to examine the effects of the rheological properties of solid-liquid suspensions on the movement of immersed bodies it is appropriate to start with non-Newtonian liquids and develop equations, analogous to those of Stokes and Newton, for laminar and turbulent flow respectively, from which quantitative information may be obtained. Further investigation would then be directed at the complex suspension systems, and the effects of the many variables on the velocity and resistance equations. Liquids are classified on a basis of viscosity which may be defined as the relationship between applied shear stress and resulting rate of shear?-'* Pure single phase liquids composed of small light molecules behave as Newtonian liquids, having a single viscosity parameter since the shearing stress and rate-of-shear are related by a linear function. Bingham plastics are similar but have a yield stress. Of particular importance in our investigation are dilatant (shear thickening) and pseudoplastic (shear thinning) non-Newtonian liquids, with and without yield values.

Jan 1, 1968

By Spencer Cragoe

I have read with much interest the elaborate and able paper of Messrs. Granger and Treville on the Mining Districts of Colombia, presented at the Atlantic City Meeting (ante, p. 33). Going into detail, however, as the paper does—and particularly with reference to the department of Antioquia, I am somewhat surprised that the property of the Frontino and Bolivia Company, probably one of the richest and most extensive in Colombia, should come off with such scant notice. The entire property embraces an area of some 28 square miles, and is situated at a distance of about 2 leagues from Remedios—after Medellin probably the most important town of the Department—and lying in approximately '7° N. latitude. The neighborhood of Remedios has been long celebrated for its production of the precious metal. Alluvial gold in large quantities has been obtained from the vicinity for upwards of two centuries; and even to-day a large proportion of the population finds a comfortable livelihood, during the dry season, in washing the sands of various rivers, notably the Rio Porce; while the amount of gold, in the form of nuggets, brought almost daily to Remedios and other points, from streams in the immediate neighborhood, is astonishing. These nuggets vary much in size. The majority, of course, are small, but larger ones are by no means scarce. I have been considerably surprised at the amount and value of the trade thus transacted between natives and merchants of the various towns. The property owned by the Frontino and Bolivia Company has been, I believe, for the larger part of the present century,

Jan 1, 1899

By Sidney H. Loram

As the work carried on by this Company, of which the writer has been in charge for the past two years, is somewhat unique, the following account of it may be of interest, and, on that account, is offered to the Institute without any attempt to claim this practice as the best. Mines. The mines supplying ore to the Company arc situated in three groups: the Guanaco field,.about 80 miles N.E. of the port of Taltal (lat. 25" S., long. 70" 30' W. of Greenwich); the Sierra Overa, about 63 miles S.W. of Taltal; and Paranao, about 42 miles due N. of Taltal (12 miles N. of the small town of Paposo, once famous for its copper-output). Guanaco. This field lies in the center of an absolutely waterless mountainous desert, where not a sign of vegetation can be found for miles. The dryness is such that ivory and horn crack and open, while raw-hide must be used in place of leather, which -would become worthless in a very short time. Water is brought about 21 miles by piping from the Cordillera, but only in small quantities, and costs in the Guanaco $7 (= $1.78 gold) per cubic meter. All supplies and food are sent from the port of Taltal, which in turn draws its supplies from the south of Chile, the

Jan 1, 1900

By J. W. Goss, M. J. Coolbaugh

Most grouting has been done to stop water flaw in mines and for stabilizing foundations of various man-made structures, a survey of the U.S. literature reveals. Apparently Sun Manuel is one of the first mines in this country to use grout extensively underground for strengthening and stabilizing ground in drifts, shafts, and stations. A comparison with other procedures as well as details of the Sun Manuel program are covered. The employment of pressure grouting as a ground stabilizer at the San Manuel Copper Corp. mine reduces delays in both development and production, lowers costs, and makes possible safer working conditions. It specifically reduces delays in haulage operations and permits the maintenance of normal ventilation. In development work this grouting allows faster excavation by cementing together highly fractured or broken ground that otherwise would require extensive cribbing or spiling. In drift repair, it consolidates the loose or fractured rock over the timber or steel drift supports, thus decreasing the frequency of repair, lessening the hazards from falling rock, and curtailing delays due to blockage of drifts by muckpiles and repair operations. Pressure grouting is the process of pumping an accurately controlled mixture of cement and water into loose, fractured, or porous rock. The ratio of water to cement varies according to the nature of the rock encountered, from the thinnest mixture of 30 gal of water per sack of cement, used to fill very fine fissures, to very thick grout of 5 gal of water per sack of cement, used to fill large fissures or extensive areas of loose, broken rock. The pumping pressures at San Manuel vary from about 100 to 1000 psi, depending upon the compactness of the rock, while at other mines the pressures sometimes go as high as 5000 psi. In order to grout an area in which ground water is encountered, the pumping pressure of the grout must be increased by an amount equal to the pressure of the ground water. GROUTING IN DEVELOPMENT WORK The areas under development at San Manuel include many sections of loose, highly fractured rock. Prior to the advent of the grouting program, drifts, shafts, and stations in these areas could not be excavated without utilizing extensive support such as cribbing, spiling, and breast boarding. This slowed down the development work and increased the costs considerably over that required for excavating in more competent ground. Now, when a particularly bad area is contacted, the mining is temporarily stopped while the bad portion of drift or shaft is grouted. After the grouting is completed, the excavating is resumed with an approximate decrease of 50 pct in lost time and costs. Grouting in Drifts and Turnouts: The grouting procedures and patterns used in drifts and turnouts are very similar. The standard procedure for grouting such a turnout is shown in Fig. 1. After the ground is supported as well as possible with cribbing or lagging, the gaps between the back lagging and side lagging are plugged with empty cement sacks or additional timber, if necessary. The ground surrounding the proposed turnout is then grouted in two stages. In the first stage, the broken and caved rock is drilled and grouted to a depth of 5 to 10 ft, depending on the depth of the broken rock. This stage forms a grouted seal that allows higher pressures to be used at depths beyond 10 ft without developing excessive leaks at the face. After a grout hole is drilled, a 10-ft long pipe is wedged tightly into it with empty cement sacks. Grout is then pumped into the hole until the pressure reaches 200 to 300 psi, and the pipe is subsequently removed if it hasn't become cemented in. No more than one hole at a time is drilled and grouted because the grout has a tendency to go from one hole into another, plugging up the latter. Five or six holes are usually adequate for the first 10 ft of grouting. Experience has shown bentonite to be a useful admixture to the grout, particularly when it is indicated that the grout is being lost into large fissures or voids. Bentonite increases the plasticity of the grout enabling it to remain in place more easily until it has begun to set. In the second stage, the longer holes are drilled through the previously grouted rock, after which the

Jan 1, 1961

By W. N. Poundstone

The mining and ventilating system used in development work in the Pittsburgh Seam in northern West Virginia is discussed. The seam conditions and the nature of the accompanying methane gas are described. The type of equipment and the mining cycle will be discussed, showing how they are well suited for very gaseous development work. Face ventilation in development work is possibly the fastest growing problem of the industry. The coal mines of the future will be faced with the prospect of mining from under increasing depths of cover. Consequently, larger and larger amounts of methane gas probably will be found. The Pittsburgh Seam, in northern West Virginia, is an example of an area already faced with this problem. At the present time, most of the development work being done in this seam lies beneath 500 to 1200 ft of cover. The Pittsburgh Seam in this area has always been very gassy—even near the outcrop—and the recent development work has been accompanied with extremely large volumes of gas. In many cases, a single development section has liberated in excess of 1,000,000 cfm in 24 hr. This problem of heavy gas liberation was the chief concern, several years ago, when continuous mining equipment was first considered at Christopher Coal Co. All of us were apprehensive about the liberation that would accompany rapid extraction in a single working place. However, the experience during the past few years has shown that this ability to mine only one place at a time, is actually the key to working this type of coal. With all of the mining or advancement concentrated in one place, the ventilation can also be concentrated. By this it is meant that continuous mining permits the active working place to be ventilated with a maximum amount of fresh air, taken directly from the intake source without first passing another working place. Continuous mining (and a good ventilating system) also permits a much greater concentration of attention or vigilance to the actual working place. There are two things that are very important to the mining of coal having high rates of liberation. First, adequate volumes of air are necessary. Second, and perhaps more important, a mining and ventilating system must be used that will provide an uninterrupted flow of air to every portion of the working section. Liberations of this magnitude take only a few seconds of interruption for a dangerous accumulation of gas to occur. With adequate volumes of air available, the ability to concentrate ventilation more than offsets the concentration of gas emission that is inherent with continuous mining. The mining system used with continuous mining equipment at Humphrey Mine is similar to the system used at many mines in the area for development work. This system is designed to favor ventilation, realizing that other efficiencies are meaningless if the equipment must stop because of ventilation difficulties. This plan is especially well suited to minimizing ventilation interruptions. Basically, the overall plan of mining is to develop headings into virgin coal and encircle or block out large areas. These blocks are generally at least 2000 ft sq. The purpose of this blocking out is to bleed gas from the area before pillaring. Experience has shown this method to be quite effective, even in the most gassy areas. The gas in this field seems to migrate or flow readily from the solid coal into the outside return headings of the development work. The numerous clay veins and slips that are found in the area are extremely good avenues for gas flow. A block of coal, surrounded with development headings, usually bleeds off readily; and since it is cut off from the virgin coal, it is not subject to gas migration, through the seam, from this source. However, the outside return of the encircling development work, adjacent to the virgin coal, may liberate gas for years. This liberation from the outside ribs in the virgin coal is the reason split ventilation is used in development work. If split ventilation were not used, there would, in many cases, be a serious build-up of gas in the intake before it could reach the working face. Fig. 1 shows a typical development section having seven headings. The two outside places on each side are returns, and the three center headings serve as intakes. This section is equipped with a ripper-type continuous mining machine. An off-track loading machine is used to load from a surge pile on the

Jan 1, 1961

By Lee Hillard Meltzer, Ralph E. Davis

INTRODUCTION During the past few years emphasis has been placed upon methods of estimating the future expectancy of gas production from natural gas fields. Before technical methods were applied, the production expectancy over future years was based upon the knowledge of gas well behavior, learned through long experience and embedded in the "know-how" of men long in the gas producing business. It is doubtful that a technical study of future expectancy of a gas field or a group of fields was ever prepared for the preliminary planning of a natural gas pipe line system built prior to about five years ago. The decline in well production capacity was naturally recognized by all familiar with the business since its earliest beginnings more than 75 years ago. In 1953, the Bureau of Mines published Monograph Number 7, "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices," which gave to the industry the first technical analysis of the decline in production of individual gas wells. This method affords a means of estimating the future production in relation to decline in reservoir pressure. The demand for technical determination of expectancy of future gas productivity from fields or a group of fields led technical men to the application of the knowledge of well behavior to the problems. The decline in a well's ability to produce as pressures declined could be estimated by the use of the curve known as the "back-pressure potential curve" as developed by the Bureau of Mines. A field containing few, or even numerous, wells could be analyzed on the basis of the sum of potentials of all wells. In most studies of this nature, the problem is to estimate the rate of production that can be expected, not only from present wells but also, from wells that will in the future have to be drilled into the reservoir being studied. The "back-pressure potential" method requires that the following data be known or estimated: (1) Proved gas reserves. (2) Current shut-in pressures and rate at which shut-in pressures change with production. (3) Back pressure potential data on wells in the source of supply. (4) Ultimate number of wells which will supply gas, and their potential. (5) Limitations on productivity such as line pressures against which the wells will produce, friction drop in the producing string, and so forth. It is evident that the resulting estimate of gas available in each year for a future of say, 20 years, contains many uncertainties. While the method may have considerable merit for a field that is fully developed, it cannot be completely dependable in fields that are only partially developed. In such cases, some of the data upon which it is based can only be estimated or assumed. In the study of this problem during the past few years, a method has been developed which we believe has great merit, especially when applied to fields subject to substantial future drilling, and when applied to the study of fields which, on the average, appear to have characteristics similar, in general, to the average of the fields used in the development of the "yardstick" outlined herein. From an analysis of the production history of 49 reservoirs which are depleted, or nearly depleted, a curve has been constructed which shows the average performance of the reservoirs during the declining stages of production. When properly applied, this "average performance curve" can be used to determine the stage of depletion at which a reservoir or group of reservoirs will no longer be able to yield a given percentage of the original reserves. "AVAILABILITY" AND "AVAILABILITY STUDIES" The rate at which. a reservoir will yield its gas depends basically upon physical factors, such as the thickness and permeability of the sand, the effect of water drive, if any, and other conditions, and upon economic factors, such as the number of wells drilled. Within the ranges set by the physical conditions, a rate of delivery tends finally to become established. The rate (or range of rates) represents a balance between the interests of the operator, who desires the maximum return from his property and of the pipe line owner, who desires to maintain a firm supply for his market. This balance, which is influenced by the terms of the contract, determines the capacity which will be developed by the operator, and the time and rate at which the decline in production is permitted to occur. Thus the "availability" of gas

Jan 1, 1953

By D. V. Edmonds, C. J. Beevers

Tensile tests were carried out on a! titanium containing 850, 1250, and 2700 ppm 0, and up to -500 ppm H. The tests were performed at -196", -78", 20°, 150°, and 300°C at a strain rate of -1.0 x 10??3 sec-1. Increasing oxygen content, increasing grain size, and decreasing test temperature resulted in enhanced embrittlement of the a titanium by the hydrogen additions. Metallographic observations showed that this can be correlated with the influence of these parameters on the introduction of cracks into the a! titanium by fracture of titanium hydride precipitates. CRAIGHEAD et al.1 reported that the hydrogen content normally found in commercial-purity a! titanium (60 to 100 ppm) was sufficient to cause a substantial lowering of the impact strength, and they attributed this embrittling effect of hydrogen to the precipitation of titanium hydride. Lenning et al.&apos; found that in commercial-purity a titanium there is an almost complete loss of impact strength at about 200 pprn H, which is approximately half the value needed to eliminate the impact strength of high-purity a titanium. They also showed that the presence of 3000 ppm hydrogen reduces the room-temperature tensile ductility of commercial-purity material to a value of the order of 10 pct; the corresponding hydrogen concentration for high-purity titanium is over 9000 ppm. It thus appears that the detrimental effect of hydrogen on the mechanical properties of commercial-purity titanium becomes evident at much lower hydrogen contents than for high-purity titanium. The main difference between the two types of a titanium might be expected to be the higher level of interstitial impurity in the commercial-purity grade. Jaffee et a1.3 studied the influence of temperature and strain rate on the hydrogen embrittlement of high-purity and commercial-purity ! titanium. In general, the behavior was the same for both materials; embrittlement was enhanced by decreasing temperature and increasing strain rate. Recent results from tests on commercial-purity a titanium containing 850 ppm O and varying amounts of hydrogen up to -500 ppm showed that the degree of embrittlement by hydrogen is intimately related to the fracture characteristics of titanium hydride precipitates.4 The present paper considers the interrelationship between the mechanical properties and micro-structural features of commercial-purity a! titanium containing 850, 1250, and 2700 ppm 0 and varying amounts of hydrogen up to -500 ppm. 1. EXPERIMENTAL PROCEDURE Three types of commercial-purity titanium supplied by IMI* were used in the investigation, and for the *Address: Witton, Birmingham 6, United Kingdom. purpose of this paper are designated Ti 115, Ti 130, and Ti 160. The principal impurity elements are given in Table I. The material was received in the form of 12.7 mm diam bars having a fully recrystallized structure. Tensile specimens with a round cross-section of 4.5 mm diam and a gage length of 15.2 mm were machined from the bars. In order to develop the same grain size (mean linear intercept of grain boundaries) in each of the three types the specimens were annealed under a dynamic vacuum of <10?5 mm Hg, Table 11. Specimen hydriding was carried out in a modified Sieverts apparatus;&apos; hydrogen was taken into solution at 450°C and after holding the specimens at this temperature for 24 hr they were furnace-cooled to room temperature at an average rate of -100 C deg per hr. By this method nominal hydrogen contents of 0, 50, 100, 250, and 500 ppm were introduced into specimens of Ti 115, Ti 130, and Ti 160 (100 ppm (wt) -0.5 at. pct). The actual hydrogen contents were calculated from the weight differences obtained by weighing the specimens before and after the hydriding treatment. Tensile tests were carried out at temperatures of -196", -78", 20°, 150°, and 300°C on a 10,000 kg In-stron machine at a nominal strain rate of -1.0 x 10-3 sec-1. Fractured specimens were sectioned in planes parallel to the tensile axis, mechanically polished to 0.25 µm grade of diamond paste, and then attack polished using a solution containing by volume 99 parts H2O, 1 part HF, and 1 part HNO3. Although the latter treatment unavoidably opened out cracks and voids visible after mechanical polishing, it did reveal the grain structure, titanium hydride morphology, and deformation twinning structure.

Jan 1, 1970