Search Documents

By R. H. Dourson, B. H. Sage, W. N. Lacey

The compositions of coexisting phases in the methane-propane-n-pentane system were determined at 160° and -2 20°F. throughout the two-phase region, at pressures above 500 lb. per sq. in. The experimental results permitted the calculation of gas-liquid equilibrium constants as well as the establishment of the critical behavior of this ternary system. Although many binary paraffin hydrocarbon systems have been investigated, the experimental work relating to the phase behavior of ternary paraffin hydrocarbon mixtures at elevated pressures is relatively scarce, being limited to a study of the meth-ane-propane-PL-pentane system at 100°F.l,2 However, Guter and co-workers have studied the phase behavior of the methane-ethane-ethylene system at relatively low temperatures. Information concerning the phase behavior of ternary systems is of value in predicting the behavior of the components in multicomponent systems, since the influence of pressure, temperature, and concentration may be individually ascertained. In the light of the importance of such information, the study of this ternary system was extended to higher temperatures in order to increase the field of temperature in which the data could be applied. Since all states encountered in this investigation are above the critical temperature of methane, the details of its phase behavior are not of direct significance. The properties of propane in the heterogeneous region were taken from a correlation3 based upon recently published data. The corresponding information for n-pentane was taken from experimentally measured vapor pressures and volumetric data.4 The rnethane-propane system has been studied throughout the two-phase region at temperatures above 70°F.,5 while the phase behavior of the propane-n-pentane system has been established for temperatures above 160°F.6 The volumetric and phase behavior of the methane-72-pentane system has been studied in detai1.7,8 The experimental measurements serve to establish with adequate accuracy the phase behavior of the components and of the constituent binary systems for this ternary system. It is believed that, with the exception of the measurements for the methane-propane system, the uncertainties in the earlier data relating to the pure substances and the binary mixtures are probably less than those associated with the values reported here. Method The methods and apparatus employed in this investigation have been described.137 In principle, the method involved the withdrawal of samples of the coexisting gas and liquid phases from a vessel containing a heterogeneous mixture of methane, propane and n-pentane. Provision was made so that

Jan 1, 1943

By W. N. Lacey, R. H. Dourson, B. H. Sage

The compositions of coexisting phases in the methane-propane-n-pentane system were determined at 160° and -2 20°F. throughout the two-phase region, at pressures above 500 lb. per sq. in. The experimental results permitted the calculation of gas-liquid equilibrium constants as well as the establishment of the critical behavior of this ternary system. Although many binary paraffin hydrocarbon systems have been investigated, the experimental work relating to the phase behavior of ternary paraffin hydrocarbon mixtures at elevated pressures is relatively scarce, being limited to a study of the meth-ane-propane-PL-pentane system at 100°F.l,2 However, Guter and co-workers have studied the phase behavior of the methane-ethane-ethylene system at relatively low temperatures. Information concerning the phase behavior of ternary systems is of value in predicting the behavior of the components in multicomponent systems, since the influence of pressure, temperature, and concentration may be individually ascertained. In the light of the importance of such information, the study of this ternary system was extended to higher temperatures in order to increase the field of temperature in which the data could be applied. Since all states encountered in this investigation are above the critical temperature of methane, the details of its phase behavior are not of direct significance. The properties of propane in the heterogeneous region were taken from a correlation3 based upon recently published data. The corresponding information for n-pentane was taken from experimentally measured vapor pressures and volumetric data.4 The rnethane-propane system has been studied throughout the two-phase region at temperatures above 70°F.,5 while the phase behavior of the propane-n-pentane system has been established for temperatures above 160°F.6 The volumetric and phase behavior of the methane-72-pentane system has been studied in detai1.7,8 The experimental measurements serve to establish with adequate accuracy the phase behavior of the components and of the constituent binary systems for this ternary system. It is believed that, with the exception of the measurements for the methane-propane system, the uncertainties in the earlier data relating to the pure substances and the binary mixtures are probably less than those associated with the values reported here. Method The methods and apparatus employed in this investigation have been described.137 In principle, the method involved the withdrawal of samples of the coexisting gas and liquid phases from a vessel containing a heterogeneous mixture of methane, propane and n-pentane. Provision was made so that

Jan 1, 1943

By Morris Muskat

ANALYTICAL calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/3 in., and to approximately one half for a perforation radius of 1/4 in,, regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings.

Jan 1, 1942

By G. Ferrara

In process and plant simulation, more reliable prediction of industrial results and evaluation of data for designing purposes may be attained by the combined use of (a) modeling and simulation of ore characteristics and (b) modeling and simulation of integrated plant operations. The systems for modeling and simulation of ore characteristics are discussed as well as the conditions in which their use may be necessary (complex structure of the ore-body and variability of the ore fed to the plant). Two examples, for coal and bauxite run-of-mine (ROM), are reported. The procedure of linking the process unit models and the approaches for the solution of integrated systems are indicated. A general-purpose program for the simulation of integrated plant operations is described, and some examples of its use are reported.

Jan 1, 1984

By Susan B. Leiter

That oxygen in copper has been a source of trouble is well known and that that trouble has been real in the commercial world has been shown by Fuller.' Moore and Beckinsale's paper2 at the annual meeting of the Institute of Metals in London, 1921, called forth considerable discussion. Prof. T. Turner expressed the opinion that it was not necessary to have cuprous oxide present in sufficiently large quantities to form either globules or seams in order to produce a bad effect if the copper were gassed. This brought up the question of the solubility of oxygen in copper and the authors desired to know whether there were any evidence of such solubility, because their experience was that whenever there was any oxygen in copper it was present in the form of free cuprous oxide, which was practically always in the form of globules. Later Hanson, Marryat, and Ford3 stated that 'for all practical purposes cuprous oxide may be regarded as insoluble in copper. However, they found particles of the eutectic to coalesce to form much larger particles. They suggested that cuprous oxide was actually slightly soluble in copper, for it was difficult otherwise to understand the mechanism by which such coalescence could take place. W. E. Ruder, in discussing that paper, said that his experiments had led him to conclude that a slight solubility must exist to allow for the ready coalescence of oxide particles, but conductivity tests convinced him that that solubility was very small. Nevertheless, there appeared to be a state of admixture of oxide with copper that closely resembled a colloidal mixture which at first was mistaken for a true solution and which usually existed at the grain boundaries. The purpose of this paper is to give the results of some investigations, begun in September, 1921, which would seem to show that although cuprous oxide may be only slightly soluble: (1) this solubility is sufficient

Jan 1, 1926

By L. C. Graton

Although marked by numerous well-known attributes of its own, gold does not possess a kind and range of physical, chemical and geological characteristics wholly different and apart from those of other metals. Instead, it is merely one of the family of metals, with its individual and distinctive traits subordinate to the underlying family relationships and resemblances. The geologist concerned with pure science will pursue, therefore, the same general course and will examine the same broad kinds of facts and interrelations when studying the occurrence of gold as when studying that of copper or cadmium, or any other metal. But when we come to consider the use and economics of the metals, we discover that gold differs strikingly from all the others. Gold, in short, is unique, not by virtue of its inherent characteristics, but because of a peculiar and concerted psychological regard in which it is held. It will be evident, therefore, that the geologist who would deal with gold supply must give far greater weight to economic considerations than is required in his contacts with any other metal. If the geologist be called the scientist of occurrence, and the economist the scientist of use, the economic geologist stands as the necessary link between them. Perhaps it is in part because the economic geologist has made himself more familiar with the science of occurrence than with the science of use and has thus in some degree failed to bridge effectively the gap between the two fields, especially with regard to gold, that the usen1 of gold now appear to be in a state of general concern and even of alarm for the security and adequacy of future supplies. In the case of no other mineral commodity do the users, as a rule, trouble themselves greatly about the adequacy of supply except in so far as that may affect the price which they shall have to pay for the commodity. Oversupply, with resulting low price, they regard as a gift of good fortune. As to long-term undersupply, they are generally content to go ahead on faith, leaving the producer to discover as best he may the means for meeting their requirements or the inventor to find a substitute. But history has shown that for gold a different situation exists. While

Jan 1, 1931

By W. A. Dunkley, W. W. Odell

The sulfur content of coal is perhaps more important in the manufacture of illuminating gas than in any other coal-using industry. Whether the gas is made by the distillation of coal in retorts or ovens or by steaming incandescent coal or coke in the water-gas process, a portion of the sulfur present in the fuel always passes into the crude gas. Practically all the sulfur that remains in the finished gas is transformed into sulfur dioxide (SO2) when the gas is burned. Sulfur dioxide is a pungent suffocating gas and, if present in the air in any perceptible amount, is deleterious to health and comfort and damaging to house furnishings. SO universally is this recognized that laws regulating the amount of sulfur that may be permitted to remain in the gas are very generally in force. The capacity of a plant to purify gas frequently limits the selection of coal for gas making. This condition may arise from different causes. Some plants were originally designed to handle a certain grade of low-sulfur gas coal, and very little leeway was allowed for growth or for the use of inferior coals. Other plants, when built, had ample capacity to purify gas from relatively higher sulfur coals, but their output has grown so rapidly that their purifying capacity is now limited and only the low-sulfur coals can be handled. There is a great quantity of coal in the United States that would satisfy the requirements of the gas manufacturer, were it not for the high sulfur content. The coals containing less than 1 per cent. sulfur are becoming scarcer year by year and, in time, the gas industry will probably be compelled to use coals that are now considered out of the question. Sulfur Compounds in CRude Gas Sulfur exists in unpurified illuminating gas in a variety of compounds; chief of these are hydrogen sulfide (H2S) and carbon disulfide (CS2). In crude coal gas H2S is usually present to the extent of 0.5 to 2.0 per cent., by volume, equivalent to about 300 to 1200 gr. per 100 cu. ft. of gas. In carbureted water gas, the amount of sulfur compounds depends not only on the sulfur content of the coal or coke used, but also upon cite

Jan 1, 1920

By I. S. Levy, J. L. Brimhall, B. Mastel

Specimens of' Hastelloy X-280, a low-cobalt version of the solid-solution- hardened nickel-base alloy Hastelloy X, were given a series of thermomechanical treatttzents. They were then Lensile-tested at room temperature and 1350°F. The Microstructures of the specimens tested at 1350°F were studied by electron Microscopy. Microscopy showed that dislocation tangling, caused by the cold working, mas still in evidence after aging-for 24 hr to temperatures as high as 1550oF. (Cr, Mo)23 C6, (Fe, Mo)6 C'. as well us an unidentifiable phase precipitale due to the combination of the thermomechanical treatments and subsequent tensile strain. The room -temperature and 1350°F tensile properties show a general increase ill strength and decreccse in ductility with increusing cold-work level. This is due to the dislocation taangling-. PerLurbatiot~s to this general trend occur- due to solid-solution weakening at the higher cold-work levels as a direct result of the preciplitation reactions. THE requirements for corrosion resistance and high-temperature strength place nickel-base alloys among the more promising materials for advanced nuclear reactor applications. However, when these alloys are irradiated at service temperatures, they generally suffer severe embrittlement'" and reduction in rupture life.3 Certain experimental treatments resulted in improvements in the tensile and stress-rupture properties of Hastelloy X-280, a solution-hardened nickel-base alloy.' To provide a basis for understanding these improvements, unirradiated tensile specimens were examined by electron microscopy. The results are reported in this paper. EXPERIMENTAL DETAILS Material. Hastelloy X-280, a low-cobalt version of Hastelloy X, is a member of the solution-hardened class of nickel-base alloys. The Hastelloy X-280 was obtained from 4- and 1-in: thick plates in the mill -annealed condition. Table I gives the chemical composition of the material as reported by the National Spectrographic Laboratories. ~x~erimental Treatments. Plates of suitable size, 12 by 3 by 1 in., or by + in., were cut under a water jet from the stock material and examined ultrasonic -ally for homogeneity of grain size and absence of voids. The acceptable plates were solution-treated at 2150°Ffor 1 hr and air-cooled. These plates were then reduced in thickness by cold rolling 0, 10, 15: or 20 pct along the original rolling direction. The plates were machined into buttonhead tensile specimens with a gage diameter of 0.125 in., with a gage length of 1.125 in., and with their tensile axes parallel to the rolling direction. The specimens were examined for quality of finish with a penetrant dye, ultra son ically checked for voids, and finally given a dimensional tolerance check with an optical comparator. The acceptable specimens were aged for 24 hr at either 1000" or 1500 F and air-cooled. These specimens were then held at 540°F in a water loop for approximately 18 days to qualify as controls for similar specimens irradiated under the same conditions of time, temperature, water chemistry, and flow rate. Table U summarizes the treatments. These treatments were investigated to establish whether prior precipitation and stabilization of carbide phases at strain sites within the matrix could reduce the amount of carbides available for precipitation at grain boundaries during service. Tensile-Test Conditions. Specimens were tested to fracture at room temperature or 1350 F in air on an Instron tensile-testing machine at a crosshead speed of 0.05 in. per min. The time for the furnace to reach equilibrium at 1350°F was approximately 30 min; soak time prior to testing was 15 min; and test duration was approximately 5 min.

Jan 1, 1968

By Karl Sundberg

ElectRical investigations carried out in regions containing sedimentary rocks showed that sediments generally are good electrical conductors, a fact which at the present time is used for structural investigations by electrical methods. It is of fundamental importance, not only for these investigations but also for electrical prospecting in general, to know the electrical properties of various soils and rocks. It will be useful, therefore, to discuss this question with the hope that the general points of view discussed in this paper will perhaps be completed by further observations and determinations of material from various localities. This paper is based principally on the study of literature, and the purpose is primarily a discussion of the main factors that determine the electrical conductivity of soils and rocks. It will follow, however, that the factors discussed here also frequently decide how far a certain orebody can be regarded as a good electrical conductor compared with the surrounding rocks. All rocks are more or less porous, and the pores are filled with liquids and gases. Their electrical conductivity, therefore, depends on the following factors: 1. The electrical conductivity of minerals composing the rock. 2. Electrical conductivity of the liquid filling the pores. 3. Proportion of the volume of liquid filling pores of the rocks to the solid rock material. 4. Shape of the pores. 5. Arrangement of the particles of gas and liquids. 6. Temperature. Dry minerals, with the exception of certain ore minerals, are complete nonconductors from the point of view of applied geophysics; in the present investigation we deal with rocks which have no conducting minerals, and factor 1, therefore, is not important. The same is true of soils. The liquids contained in soils and rocks in most cases are waters, sometimes oil. As oil is a nonconductor of electricity, the impregnating waters will determine the electrical conductivity of soils and rocks.

Jan 1, 1932

By Richard Franchot

IN the inevitable conquest of the blast furnace by metallurgical science in the solution of the problem of how to make more and better iron or to burn less coke, or both, it is highly desirable first to find out why the efficiency of the furnace generally is no better than it is. The immediate need would seem to be a theory to account for the existing facts. Explanation for the quantitative results obtained in current practice has been strangely lacking. One reason for this may be found perhaps in the custom of think-ing of efficiency in terms of coke consumption. Before efficiency can be explained there should be a fairly exact knowledge of what it is. A statement of the pounds of coke used per ton of iron made may have value in indicating comparative results in smelting similar ores with similar cokes, but it tells very little of the efficiency of the operation. When the materials are different, one practice burning 1800 lb. may be less efficient than another using 2000 lb. A better measure is the pig and slag per unit of coke. What is needed is a specific description of efficiency as a' definite quantity having an exact meaning. Such description is afforded by expressing efficiencies in terms of the respective proportions of the fuel energy absorbed in and chargeable to the various actions known to be -taking place in the furnace. Concretely, the energy value of a pound of coke having 85 per cent carbon blown with air heated to 1200° F. is about 7650 lb.-cal. (13,770 B.t.u.). And the work done in smelting a pound of average iron from hematite, comprising reduction and melting with production of a half pound of free running slag from an equal weight of limestone,

Jan 9, 1926

By Dorsey A. Lyon, Robert M. Keeney

Page I. Introduction..........234 I1. Chemistry oF Copper Smelting...235 1. Native Copper Ores.......235 2. Oxide and Carbonate Ores....235 3. Sulphide Ores.......236 (a) Elimination of sulphur ...236 III. Reverberatory Copper Smelting...237 IV. Substitution of the Electric Furnace for the Reverberatory Furnace..................... 238 V. Smelting of Fine Michigan Native-copper Concentrates in the Electric Furnace.................. 239 1. Conclusions.................240 VI. Proposed Process for Electric melting of Fine Native-copper Concentrates.................. 241 VII. OrdINary Copper Blast Furnace 'Smelting......... 245 1. Prerequisites.................. 245 2. Losses .................... 247 VIII. Experimental Data on the Electric Smelting of Raw Sulphide. Oxidized and Carbonate Ores............. 248 1. Vattier's experiment................ 248 2. Wolkoff's experiments................ 249 3. Experiments of Stephan.............. 250 (a) Conclusions of Stephan ............ 251 IX. Smelting of Sulphide Ores in the Electric Furnace...... 251 1. Ores Treated.................. 252 2. Conclusions................... 253 X. ELectric Furnace vs. the Reverberatory Furnace and Blast Furnace as a Melting Agent.............. 253 XI. Smelting of Sulphide Ores without Roasting or Partial Pyritic Smelting............254 XII. The Electric Blast Furnace vs. the Copper Blast Furnace for Partial Pyritic Smelting.......259 1. Metallurgical conditions......259 2. Mechanical considerations......259 3. Comparison of costs.......260 (a) General considerations .....260 (b) Cost of plant........260 (c) Amount of electrical energy...260 (d) Cost of smelting.......261 (e) Cost of electrodes........262 XIII. The Use of the Electric Furnace in the Smelting of PyRITIc ORES : 262 XIV. Summary...................... 264

Jan 1, 1914

By Robert W. Hunt

(Cleveland meeting, October, 1912.) PERHAPS of all the scientific economic questions which have been claiming the attention of capitalists, metallurgists, manu-facturers, directors of public utilities, and the general public of America, during the last few years, none have been of more importance than the one relating to the wear and safety of steel rails. The discovery of the Bessemer process made possible modern railway development. In that growth, as has generally happened in all progressive movements, ill its department have not remained equally balanced. Iron rails permitted the construction of roadways for the passage of power-driven vehicles. In time the speed and weight of such carriages proved too much for the wearing-qualities of the rails, and the limit of railway capacity seemed to have been reached. Bessemer made his invention, which was soon perfected and developed, especially as related to steel rails, and thereby increased the limit of capacity, acid vastly greater railway progress was, made possible. The Siemens-Martin open-hearth process followed, and was later supplemented by the Thomas-Gilchrist basic improvement. For a time the Bessemer steel rails of commerce Were, more than equal to all that was asked of them, but this did not long continue, as evidenced by the records in our Transactions. Revolutionary changes occurred in the industrial world, and in no part of it more than in steel-rail manufacture. Great and powerful commercial combinations were made, whose financial resources made possible the supplanting of the then most efficient blast-furnaces, steel-works, mid mills, by others of theretofore unimagined capacity. Old traditions and practices of steel-making were wiped away, and, in too many cases, output was apparently the chief aim, with the result that much dissatisfaction with the wear and safety of rails was felt by railway officials, and the general public was concerned as to its safety when traveling. The climatic conditions of the winter

Dec 1, 1912

By J. W. Craig, H. L. Walker

Industry has for many years recognized the dependence of certain mechanical and physical properties. as well as workability, upon grain size variations in brass. Although the dependence of properties upon grain size has been recognized there are not many instances where a planned program of testing has been conducted and where the only intentional variable has been grain size. In particular the literature is limited with respect to the effect of grain size on the endurance limit, though there are many industrial applications where the brasses are subjected to cycles of repetitive stresses. Literature A number of the physical and mechanical properties of a given brass sheet, in the annealed condition, will depend upon: (I) The ready-to-finish grain size before final rolling, (2) the percentage deformation by cold working, and (3) the time and temperature of annealing. The first and second variables affect the recrystallized grain size, and the third variable affects the coalesced grain size. Gibbsl has shown the effect of two different ready-to-finish grain sizes upon the tensile strength and hardness of deep drawing brass strip after a definite amount of cold rolling. The smaller the ready-to-finish grain size, the higher the tensile strength and hardness, but with lowered ductility, Gibbs also demonstrated, for a given time and temperature of anneal, that the tensile strength, hardness, and elastic limit are higher for the smaller ready-to-finish grain size, but the elongation is lowered. Townsend and Greena112 have reported data which show that cold working increases the tensile strength, hardness, and load carrying ability of deep drawing brass sheet under reversed stress. Greenall and Gohn3 have reported data which show that the smaller grain sizes have higher tensile strength and hardness properties, and the data also show that increased cold working increases the tensile strength and hardness properties of deep drawing brass sheet. Kommers4 has reported data for tests of brass of known ready-to-finish grain size, a specific amount of cold reduction, and annealed at different temperatures above and below the recrystallization temperature. Kommers' results indicate that annealing below the recrystallization temperature does not change the tensile strength and hardness properties, but the endurance limit may be increased from 22,000 to 28,000 psi. The increased endurance limit is explained as resulting from the reduction of internal stresses by a stress-relief anneal. Burghoff5 and associates have reported data on creep tests, over

Jan 1, 1949

By N. Nemeth, L. L. Sirois

The role of the filter medium in continuous-vacuum filtration and the special circumstances which influence the resistance to flow through the porous cake and filter cloth are discussed. Due to negative pressure differential, gas bubbles evolve in the slurry, constrict passages in the filter cake and medium, and further restrict flow through the tortuous channels. Filtration is a liquid-solid separation process taking place at a porous medium under a pressure differential. The liquid passes through the medium; the solids are retained on the medium as a partially dewatered cake. Filtration is far from a simple process and has been described in terms ranging from "complex" to "subtle." Because of the many variables involved, no unified filtration theory has been developed, and the filtration process is still considered very much an art. In industrial filter design, basic relationships, whether derived for idealized conditions or developed empirically, are usually adapted to suit local conditions. In the mining industry where continuous-vacuum filtration is the main dewatering process, the physical state of the concentrates and the relatively low pressure differentials permit the assumption that the cakes are noncompressible, an assumption which leads to the use of theoretically sound rate equations. Notwithstanding this simplification, there are other problems, unique in the application of vacuum to dewatering, and until now completely ignored, which demand special attention. The basics of filtration involve the capture of solids on, while permitting the flow of liquid through, a porous layer of cake and cloth. Flow is determined by the structure of the solids which make up the cake and the particles permanently attached to the cloth. The problem of this structure, essentially one of solid geometry, has been considered insoluble by Hatscheckl as early as 1907 and by Freshwater as recently as 1967. Since cake structure is determined by the slurry parameters, that problem is far too large for inclusion in this study. For theoretical considerations, uniform buildup of the filter cake must be assumed; and for efficient practical operation, the resistance of the medium must be kept constant over long periods. The latter can be achieved by careful selection of the filter cloth, since the greatest part of the total filtration resistance will develop at the cake-cloth contact. This paper discusses the role of the filter medium in continuous vacuum filtration and the special circumstances which influence the resistance to flow through the porous cake and the filter cloth.

Jan 1, 1971

By J. B. Austin

In considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these efficiencies are more useful than others, yet all are instructive; for a knowledge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermodynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By D. A. Woodford

In a constant-load creep test, if the density of nlobile dislocations is assumed constant for strains exceeding that corvesponding to the minimum creep rate, it is shown that the creep rate may be approximated by the equation where E is the nominal strain, o0. is the initial stress, and a' the stress fov unit dislocation velocity. The constant C contains the mean density of mobile dislocations and n is a measure of the stress sensitivity of dislocation celocity. This equation is shoum to be applicable to published data on an alloy steel and on nickel. The degree of plastic instability and hence the creep ductility is dependent on the calue of n for these materials. When instability becomes gross and local macroscopic necking occurs, the assumptions are no longer valid. On the basis of this equation, and the strain-time relation derived from it, a method of predicting the creep behavior at different stresses is suggested. MOst analyses of creep data have been concerned with time-dependent transient creep or time-independ- ent secondary creep in constant-stress tests. The far more widely used constant-load test has been neglected in terms of a mechanistic approach. In general, since the strains involved are usually small, the same laws for transient creep may be applied to both types of tests. However, there is no steady-state creep in a constant-load test since the stress increases continuously. Any apparent steady state observed on a strain-time plot is either fortuitous or illusory, and is generally revealed as a continuously varying creep rate on a carefully constructed strain rate vs time plot.* Transient creep may be understood in terms of a simple differential equation representing the change in mobile dislocation density with time:' where p is the density of mobile dislocations. The first term on the right is related to first-order kinetics of dislocation multiDlication and the second to second-order kinetics of exhaustion. On the basis of this equation, several authors2-4 have found good agreement with experimental transient creep curves for a number of materials. When k1p = k2p2, a steady-state creep

Jan 1, 1968

By Carl Davis

A description is given of grinding practice on the Rand and of experiments made to improve that practice. The paper includes a description of the experimental plants and methods and the results obtained. THE first tube-mill on the Rand was put into operation in May, 1904, at the Glen Deep Mine. From that time onwards, tube-mills were added to various plants, although little was known regarding the capacity of a given tube-mill when working on banket ore. Within a few years, however, the so-called standard size (length of shell 22 ft. 0 in. diameter 5 ft. 6 in.) was generally used until the last year or two. Practically the only exceptions were about 30 tube-mills having a length of 16 ft. and a diameter of 6 ft., and a few open-end mills of the roller-supported type. Most of the information obtained during the last 15 years has been obtained with mills of the standard dimensions. The adoption of the tube-mill as an accessory to the stamp mill was rapid; and where 3 tube-mills were working on the Rand at the end of 1904, 244 were in use seven years later.1 By 1910, good practice provided 1 tube-mill for 20 stamps of 2000-lb. falling weight. The horsepower of the motors driving the tube-mills had increased from. 80 to 100 and then to 125 at this date. Broadly speaking, current practice at that date aimed at a final product of which 60 per cent. was suitable for sand treatment and 40 per cent. for slime. The sand grading was +60 mesh, 6 per cent.; +90 mesh, 25 per cent.; -90 mesh, 69 per cent.; and the slime grading -200 mesh, 2 per cent.; -200 mesh, 98 per cent.

Jan 12, 1924

By John Gross

A SURVEY of the status of ore dressing in 19231 placed particular stress on the need of research in the crushing and grinding of ore, especially on the need for a method of measuring the surface of the products obtained in crushing and grinding, and for fundamental data on the law of crushing, in order that intelligent conclusions may be drawn from actual crushing or grinding experiments. There has been no satisfactory means of determining the surface of crushed products. The results have been judged entirely by the amount of the various sizes produced, based on sieve sizing for particles above 74 microns in size and on microscopic measurement or elutriation for particles below 74 microns, a method which could give only a general idea of what had been accomplished. The fact that the long controversy between the followers of Kick and of Rittinger has resulted in no accepted conclusion is evidence of the need for fundamental data on the crushing law.

Jan 1, 1928

By T. A. O’Hara

SINCE May 1948, when tungsten carbide bits were introduced at the Flin Flon mine, they have been popular with the miners because of their fast drilling speed and low gage loss. The high cost of commercial carbide bits and tipped drill steel, however, prevented their use except for the hardest rock. In an effort to extend the use of tungsten carbide on a basis economically competitive with detachable steel bits, experimental work was begun in 1950 to test the feasibility of making tungsten carbide tipped drill steel in the mine drill steel shop. This work showed that tipped drill steel could be made locally at less than half the cost of the commercial product. The performance of the local tipped drill steel was comparable to that obtained with commercial carbide bits and tipped drill steel and the cost per foot drilled was much lower. Local tipped drill steel was adopted for all mine drilling in November 1951. Since then drilling costs per foot have been sharply reduced and footage drilled per manshift has increased markedly. Experience at Flin Flon has shown that production of satisfactory carbide tipped drill steel is not difficult and that highly skilled labor and costly equipment are not required. As long as wise selection of brazing materials is made and certain simple precautions are rigidly maintained, there is no reason why small mines with relatively unskilled labor cannot produce a satisfactory product. The following description outlines the technique used at Flin Flon for making carbide tipped drill steel and discusses characteristics of the brazing process that make special precautions necessary. Drill steel is forged to four-wing shape in a conventional steel sharpening forge. Standard steel dies are modified to minimize forging cracks around the central waterhole and to forge a blunt bithead on the steel. The steel is preheated to 1500°F and held at this temperature for at least 2 min. When the temperature has equalized throughout the steel section, the drill steel is transferred to the forging furnace and heated rapidly with a reducing flame up to 2000°F. This two-stage method of heating minimizes the grain growth and decarburization of the steel while ensuring that the steel temperature does not vary greatly throughout the forging zone. After forging the steel is allowed to cool in air to about 1600°F before being annealed in a bath of vermiculite. Despite the high hardenability of the 3 pct Ni-Cr-Mo drill steel used, this simple treatment anneals the drill steel sufficiently for milling. The forged and annealed drill steel is slotted on a plain horizontal milling machine that is equipped with a quick opening chuck and a slot depth stop. The full depth of the slot is milled in a single pass of the 3-in. milling cutter which is fed at 33/4 in. per min across the crown of each bit wing. The slots are cut to a width of 0.342 to 0.344 in. Maintenance of this slot width is necessary to ensure that the optimum brazing clearance of 0.002 in. will result after assembling of shims and carbide in the slot. Prior to March 1953, when the milling machine was installed, drill steel was slotted on a small manually fed ¾ hp milling attachment mounted on the bed of a lathe. Over 16,000 drill steels were slotted on this unit, and in view of its small size and low cost it gave excellent service. Brazing of Tipped Steel Drill steel that has been milled and cleaned in carbon tetrachloride is mounted in a rotating cradle holding six drill steels, the length of which may be from 2 to 12 ft. The slots in the drill steel, the shims, and the tungsten carbide inserts are thoroughly fluxed with a fluoride flux and assembled as shown in Fig. 1. Fig. 2 shows the brazing equipment in use. As the ring burner is lowered over the bithead a spring valve opens the gas lines, and the gas mixture, preset to give a slightly reducing flame, is fed to the ring burner where it is lit from a pilot flame. The ring burner heats the drill steel over a zone about 1 to 2 in. below the bithead, which becomes heated by conduction through the steel. By this means the bithead is heated rapidly and evenly, and contamination of the brazing joint with soot from the flame is avoided. The bithead is heated to the melting temperature of the brazing alloy within 1 min. This rapid heating minimizes the disadvantage of a non-eutectic brazing alloy. The brazing alloy, a nickel-bearing quaternary alloy, is placed at the bottom of the slot below the carbide insert, as shown in Fig. 1. As the brazing alloy melts it is drawn by displacement by the carbide and by capillary action into all parts of the joint to displace liquid flux from metal surfaces. As soon as the brazing alloy melts, each insert in turn is wiped by being moved back and forth along the slot. This action assists wetting of the carbide by the brazing alloy and assists in displacing molten flux from the joint. After continuous heating for about 75 sec, when the bithead has reached a temperature of about 1500°F, the ring burner is raised and the gas supply is shut off automatically by the spring valve. As soon as heating is stopped a hand press is placed on the bithead and the inserts are squeezed down firmly. This action minimizes the clearance between the bottom of the insert and the slot. Correctly brazed steel should maintain a clearance at the bottom of the slot of 0.001 to 0.002 in. After six steels have been brazed they are removed from the cradle and allowed to cool in air. As soon as each drill steel is cool it is dressed on a grinding wheel to remove excess flux and braze and is ground to the gage appropriate to the length of the drill steel.

Jan 1, 1955

By J. D. Milburn, H. J. Hill

In quantitative interpretation of electrical logs the presence of clay minerals introduces an additional variable which further complicates an already complex problern. Although recognizing the difficulties introduced as a result of the heterogeneity of natural sediments and despite the present incomplete state of knowledge regarding electrochemical behavior of shales, dissemirzated clay minerals and concentrated electrolytes, it was felt that useful empirical correlations might be obtained from experimental investigation. Six typical sandstone formations, having a wide variety of petrophysical properties, were selected for the study. Approximately 45 samples from each formation were selected to satisfactorily represent the range of pore size distribution within the particular formation, As a matter of general interest, four limestone formations were also included in the investigation. Previously proposed equations relating to resistivity, SP and interrelationship of the two phenomena have, where possible, been tested with data obtained in this investigation. These equations do not satisfactorily describe experimental behavior of samples through all degrees of shaliness or throughout the range of brine solution resistivities normally encountered in logging practice. An empirical equation has been developed which quantitatively relates formation resistivity factor to satirrnting solution resistivity, porosity, and "effective clay content." This relation is indicated to be uniformly applicable to clean or shaly reservoir rocks. It is shown that both the SP and resistivity phenomena of shaly samples are related to the sample cation exchange capacity per unit pore volume. The independent chemical determination of this parameter is thus a means of determining the "effective clay content" of samples. Some implications regarding theory and electric log interpretation of shaly sands are discussed. INTRODUCTION The use of electrical resistivity logs as a means for estimating formation porosity is based upon the original work of Archie1. It was shown by empirical methods that the resistivity of a rock, when 100 per cent saturated with brine solution, could be related to rock porosity through the equation, F = Ro/ RW = f-m.......(1) where F, the formation resistivity factor, is defined as the ratio of the resistivity of the 100 per cent water saturated rock, Ro, to the saturating solution resistivity, Rw; f is the ratio of pore volume to bulk volume; and m is the slope of the average line when the data are plotted on log-log paper. This relation was established for relatively shale-free formations containing water having high salt concentrations, and under these conditions F may be considered constant for a given rock sample. Applications of Eq. 1 to interpretation of logs of shale-free formations has been quite successful when satisfactory formation water resistivity data could be obtained. The most readily available means of estimating formation water resistivity is the self-potential log. Conventional methods of SP log interpretation involve correct.

Jan 1, 1957