Search Documents

By C. Gatlin, N. E. Garner, A. Podio

Experimental data from single chisel blows on Leuders limestone are presented. A pressure chamber, similar in design to well known microbit drilling chambers, was utilized to impose variorcs stress states on the sample. Confining pressure of zero to 10,000 psi and borehole pressures from zero to 5,000 psi have been used in the studies. Pore pressure was zero and the rock samples dry in all instances. Force-displacement records and visual examination of the craters indicate that the mode of failure depends on both confining and borehole pressure in certain ranges, ranging from brittle, through a transition, to near plastic. The mode of failure is reflected in the observed blow force and energy data, as well as the shape of force-penetration curves. INTRODUCTION A previous paper' presented initial data from the project on which this paper is the second report. While the first paper dealt with impact studies on synthetic rocks, the literature cited there is also pertinent to this paper, but will not be listed again in order to avoid needless repetition. This paper presents experimental data from single chisel impacts on limestone at certain simulated wellbore stress states. Specific variables investigated were combinations of borehole and confining pressure, crater geometry, a narrow range of impact velocity and the forces required to drive the chisel into the specimens under the varying conditions. EXPERIMENTAL PROCEDURE The same basic apparatus described in our earlier paper, except for the pressure vessel, was used in this study. Fig. 1 shows the complete experimental system. Fig. 2 shows details of the pressure cell, which is quite similar to the well known microbit drilling chamber. The confining (overburden) pressure system provides independent pressure control over the sample except for two, 21/4 in. diameter areas located on the sample ends. These two areas provide a pore pressure entrance on the bottom and a striking surface on the top where borehole pressure can be controlled. The ends are isolated from the confining pressure by O-ring seals. The borehole and pore pressures are related through the striking surface; they will be the same unless a seal is deposited on the borehole surface, either a mud cake or some other impermeable membrane. In these studies pore pressure control was not used, as the rocks were dry and unsaturated in all cases. Rock samples were prepared from 4-in. cubes as illustrated by Fig. 3. The circular disks of adhesive vinyl plastic protected the impact surface from the resin coating (Scotchcast No. 2) and were removed just prior to each test. This procedure insured a fresh uncontaminated surface for the impact. Fig. 4 shows the dimensions and loading of the sample, including the concentrations around the "borehole" periphery (O-ring seal). The rock used in this study was Leuders limestone, of Permian age (Leonard), quarried near Leuders, Tex. Geologically, Leuders limestone is a light gray, fossili-ferous limestone (oolitic foraminifera1 biosporite). Its fossil content is 80 to 90 per cent and consists primarily of calcitornellid, ostracods, pelecypods and oolites with the remaining part intraclasts. There are hematite or limo-nite rims on some of the intraclasts. The porosity is approximately 20 per cent, but the permeability is less than 1 md. There is no apparent orientation in the structure. Triaxial tests have been conducted to determine the variation of the physical properties of Leuders limestone in three orthogonal directions', and it is known to be unusually isotropic and uniform. Physical parameters for this rock are: uniaxial compressive strength = 9,700 psi; F = 32 and C = 2,700 psi; where + and C are Coulomb equation values (t = C+u tan +). Impact tests were run under the combinations of confining and borehole pressures shown in Table 1. Samples were dry with atmospheric pore pressure in all cases. Tests, in which elevated borehole pressures were applied, used a single layer of household Saran-Wrap to prevent horehole fluid invasion into the sample. This proved to be simple and reliable. The blunt wedge used in all the tests was 0.75 in. long and had an included angle of 60" with a 0.05-in. flat. In addition, a sharp 60" wedge was used for all confining pressures at zero borehole pressure. The chipper speed

By J. L. Kenty, J. P. Hirth

The concept of a critical super saturation, below which the nucleation rate is essentially zero and above which it is essentially infinite, is discussed with reference to vapor-solid nucleation. The necessary and sufficient conditions deduced for observations of this type of behavior are: 1) the nucleation rate must exhibit a sharp dependence on super saturation, 2) the growth rate must be sufficiently large that nuclei become observable in the time period of the experiment, and 3) the number of highly preferred nucleation sites must be small. Experiments reveal that the nucleation of silver on sodium chloride is visually detectable at all experimentally accessible super saturations and does not exhibit critical nucleation behavior. Failure to observe a critical super saturation is attributed to the insensitivity of nucleation rate to supersaturation as a consequence of the particular values of the contact angle and the surface free energy for this system. THE concept of a critical supersaturation, below which the nucleation rate is essentially zero and above which it is essentially infinite, arises naturally in homogeneous nucleation theory. Experimentally this type of behavior has been found by Volmer1 and others for water and other low surface tension liquids, as reviewed by several authors.2'3 The same type of behavior has been predicted and observed for heterogeneous nucleation of solids by Yang et al.4 and others,596 as also recently reviewed.2,7,8 In the work reported here on the heterogeneous nucleation of silver on NaC1, however, no critical super-saturation was found. Similar observations have been made recently for other systems.9-11 These results led to a reexamination of nucleation theory which revealed that there are conditions for which critical behavior is not predicted, either for homogeneous or heterogeneous nucleation. Although heterogeneous nucleation is of primary importance in this paper, some insight into critical behavior for such a case can be gained by considering homogeneous nucleation. Accordingly both types of nucleation theory are reviewed briefly. The requisite conditions for critical supersaturation behavior are then considered. The experimental results for the nucleation of silver on NaCl are presented and interpreted in terms of the theoretical presentation. REVIEW OF NUCLEATION THEORY There are essentially two approaches to nucleation theory, the so-called classical theory involving the concepts of bulk thermodynamics, and the statistical mechanical theory in which nuclei are regarded as macromolecules. The classical theory is based on the work of Volmer and Weber12,13 and Becker and. Doring14 and has been extended by Pound et al.15 The crucial assumption in the classical theory is that the small clusters or nuclei can be characterized by the same thermodynamic properties as those of the stable bulk phase. Thus, the nuclei are assumed to have a surface free energy, y, and a volume free energy of formation (relative to the vapor phase), ,, identical to that of the bulk. For deposition under low super-saturation conditions, the nuclei are large and this assumption is satisfactory. However, in many cases of interest, the nuclei contain only a few atoms and this assumption is highly questionable. The statistical mechanical models originated, for the specific case of a dimer as the critical nucleus, with the work of Frenkel16 and were extended later to larger sizes by Walton,17,18 Hirth19 and, more recently, Ht Zinsmeister. These models describe the nucleus in terms of a partition function, the estimation of which is tractable for clusters of 2 to 10 atoms, but extremely difficult for clusters larger than 10 atoms. Although the classical and statistical mechanical models are expected to apply for the limiting cases of large and small nuclei, both are uncertain for intermediate sizes. In this paper we shall treat only the classical model, recognizing that it is exact only for large nucleus sizes and regarding it as a phenom-enological description for small nucleus sizes. When analyses of experimental data using bulk properties show the nucleus size to be small, the resulting parameters should be regarded as largely empirical parameters describing the relative nucleation potency of the system. Considerable justification for the continued use of classical theory is provided by its general success in predicting nucleation behavior as a function of supersaturation and temperature. We emphasize that the qualitative features of the statistical mechanical models, particularly the critical super-saturation behavior that is central to the present work, are the same as those of the classical model. Of course, potential energy terms and surface partition functions replace the volume and surface energy terms of the latter model. The most recent versions of classical nucleation theory have been extensively reviewed.2,3,7 so that only the results are presented here. For homogeneous nucleation of a condensed phase from the vapor phase, the volume free energy change is ?Gv=vrT = =^ln£ [1] where v is the molecular volume of the condensing species. The supersaturation ratio,

Jan 1, 1970

By L. J. Kashar

By means of a continuum-mechanics approach, the following equation for calculuting the pressure for axisymmetric cold forging has been derived: where P is the extrusion pressure; K and n are the strength coefficient and the strain-hardening exponent of the steel, respectively; a and b are strain factors, primarily dependent on the die design; and R is the extrusion ratio. Data from compression and backward-extrusion tests performed at a crosshead speed of 0.5 in. per min on a nonwork-hardening material pure lead) and on a work-hardening material (1018 steel) indicate that the predicted extrusion pressures obtained from the derived equation agree very closely with the actual extrusion pressures. Therefore, the equation can be used to predict backward-extrusion pressures from standard mechanical-test data. The decision to cold-forge a part is based on several considerations, most of them related to economics. However, the production feasibility is usually determined by the pressure needed to extrude the part and the availability of tooling that can repeatedly sustain this pressure for over several hundred thousand cycles. A major contribution to the cold forging of steel would result from the development of steels that could be forged at reduced pressures and from the development of techniques that permit the accurate prediction of the pressure necessary to cold-forge the part. The ability to predict extrusion pressures is necessary to properly design the tooling required for the cold-forging process. Attempts to theoretically predict the cold-forging pressure, especially for work-hardening materials, have been unsuccessful in previous investigations of the cold-forging process.1-3 Many empirical relations have, therefore, been proposed relating the extrusion pressure to the chemical composition,' the extrusion ratio,2 the tensile strength,273 and hard- ness, 2 and the yield strength3 of the material being extruded. However, these empirical relations are valid only for the specific conditions used in their development, and, in some cases, the empirical relations had a scatter band greater than * 10 pct. A study of the extrusion process was undertaken with the objective of developing predictor equations for extrusion pressure by using a continuum-mechanics approach to the problem of metal flow. The derivation of such an equation is summarized in this paper, and data are presented that confirm the validity of the derived equation. DERIVATION OF THE EXTRUSION EQUATION If the extrusion of a material through a die is considered in terms of a work balance, it has been shown that it is possible to derive an equation relating the work necessary to move the material through the die to the deformation work undergone by the material. The work done, W, in moving the material is given by where F is the extrusion force, I, is the distance the material was moved, A, is the original cross-sectional area of the material, P is the extrusion pressure acting on A,, Ap is the cross-sectional area of the extrusion punch, and Pp is the punch pressure acting on Ap. The deformation work, WD, is given by where V is the volume of metal deformed, ay is the flow stress of the metal, and E is the total strain undergone in the extrusion. If there are no frictional losses, the work done, W, is equal to the deformation work, WD; therefore, Since the volume of a metal does not change during deformation,

Jan 1, 1968

By L. O. Brockway, W. C. Bigelow, J. A. Amy

Specimens of Inconel-X alloy solution-treated at 2050°F and aged for periods of 1, 10, 100, and 1000 hr at 1200°, 1400°, and 1600°F have been examined by electron microscopy and by electron and X-ray diffraction. Four minor phases were identified: titanium nitride, niobium nitride, an M23C6 complex carbide, and the intermetallic ? phase. The two nitrides were found in all of the aged specimens and in the solution-treated alloy, the y' phase formed at all aging temperatures, while the M23C6 carbide formed only on aging at 1200° and 1400°F. Variations in the hardness, rupture strength, creep strength, and yield strength of the alloy have been shown to be related to variation in the size and distribution of the particles of the y' phase within the matrix grains of the alloy, with maximum values of these properties occurring when there is a maximum amount of the phase present and a fine state of dispersion of the particles prevails. THE nickel-chromium alloys containing titanium and aluminum are widely used in applications requiring high strength at elevated temperatures. Studies on relatively simple ternary and quaternary alloys'-4 have indicated that the favorable high-temperature properties of these alloys are related to the precipitation of an intermetallic ?'-phase having a structure based On that of the Ni3A1 phase of the nickel-aluminum system. The present investigation was undertaken to identify the minor phases and to study the microstructural changes occurring in one of the more complex commercial alloys as a result of aging in the service temperature range, with particular emphasis on investigating the role of the ?' -phase. The microstructural changes were studied by electron microscopy and the minor phases were identified by X-ray and electron diffraction. MATERIALS AND METHODS Inconel-X alloy was selected for this investigation because the previous studies of Frey, Freeman, and white6 provided extensive information on the variations in metallurgical properties of this alloy resulting from high-temperature aging treatments. Specimens aged 1, 10, 100, and 1000 hr at 1200°, 1400°, and 1600°F were made available for the present use. These were taken from 1-in. round-bar stock of a commercial heat having the following weight composition: 0.04 C, 0.56 Mn, 6.59 Fe, 0.007 S, 0.38 Si, 0.03 Cu, 73.22 Ni, 14.97 Cr, 0.78 Al, 2.38 Ti, and 1-02 Nb. They were solutjon-treated at 2050 for 4 hr and then water-quenched prior to aging. Powder X-ray diffraction patterns were obtained from insoluble minor phases which were separated from the alloys by digestion in the reagent of Mahla and Nielsen.6 Back-reflection patterns were obtained from electrolytically polished surfaces of the bulk search to detect the ?'-phase' Cu-K a radiation was used in both cases. In the electron-diffraction studies, the general method developed by Heidenreich, Sturkey, and

Jan 1, 1959

By E. S. Bartlett, D. N. Williams

QUANTITATIVE values for the oxidation rate of unalloyed molybdenum in air at temperatures above the melting point (1460°F) of the characteristic oxide are contained in the literature as a result of previous investigations. Lustman' reported values corresponding to 0.36 in. penetration per day (IPD) at 1500 and 1600°F in still air, noting essentially no variation in rate with temperature. Jones, Spretnak, and Speiser' reported values corresponding to 0.14 and 0.13 IPD at 1500 and 1800°F, respectively, in still air, attributing the decreased oxidation rate at higher temperatures to a lesser accumulation of the corrosive molten oxide on the surface at the higher temperature as a result of increased volatilization rate. Harwood3 ecently summarized work in the field, presenting generalized data corresponding to 0.48 to 0.96 IPD at 1800°F and 0.55 to 0.83 IPD at 1700°F in slowly flowing air. In a recent program at Battelle, it became desirable to know more about the characteristic oxidation behavior of molybdenum under varying conditions of temperature and atmosphere. Using oxidation-test apparatus designed for dynamic, continuous recording of weight change during testing,' values for the oxidation rate of molybdenum were obtained at temperatures from 1400 to 2150°F. In addition the effect of air flow on the oxidation rate was studied briefly at temperatures of 1600, 1800, and 2000°F. Exhaust of the contaminated atmosphere from the oxidation chamber was effected by an impeller pump attached to a 3/16-in.-diam opening in the oxidation chamber. The volumetric exhaust rate (cubic feet per hour) was normally maintained slightly in excess of the input rate to avoid condensation of MOO,,' on the sample suspension rod. The entering atmosphere was preheated prior to admission to the oxidation chamber by a 1 1/2-in.-diam cup packed with shredded asbestos. The experimental data are presented in Table I. Comparing conditions 2 and 3 (taking into account the temperature difference) and conditions 8 and 9. shows that in the absence of forced exhaust an atmosphere of moving air results in greater oxidation rate than a stagnant atmosphere. The use of forced exhaust, as shown by comparing conditions 3 and 4 and conditions 14 and 15: resulted in an even greater increase in oxidation rate. By virtue of the size of the atmosphere input and exhaust openings, it was calculated that the exhaust velocity was about 60 times that of the input velocity for essentially equal volumetric flow rates. Because of the proximity (about 3/4 in.) of the exhaust port to the specimen, it is logical to assume that cleansing of the atmosphere immediately surrounding the specimen was accomplished much more efficiently by the exhaust flow than by the input flow at a constant-volumetric flow rate. Also, it can be seen by comparing conditions 4 through 7 and conditions 11 through 13 that increasing the rate of atmosphere flow (by increasing input velocity with a proportional increase in exhaust velocity) above some optimum value has little, if any, further effect on the oxidation rate. These results suggest that there is a maximum oxidation rate for molydenum at a given temperature which is obtained when conditions are maintained such that the partial pressure of MOO3 in the atmosphere surrounding the specimen is at a low value. By controlling the partial pressure of MOO, surrounding the sample, it is possible to control the rate of volatilization of MOO:, from the surface. This, in turn, affects the rate of oxidation, since the thickness of the MOO3 layer determines the amount of oxygen which will be able to reach the reaction surface.' When the liquid oxide layer is less than some critical thickness, i.e., when the volatilization rate is high, enough oxygen is transported to the active surface to permit oxidation to proceed at the maximum rate allowed by the kinetics of the oxidation reaction. However, if the volatilization of MOO,, is suppressed, the thickness of the layer of MOO3 on the surface increases, and the diffusion of oxygen through the oxide layer becomes the rate-controlling step in the oxidation process. The lack of agreement between the present results and those of previous investigators is presumed to be due to differences in removal of the oxidation product (Moo,) from the immediate vicinity of the sample. By comparing conditions 1, 5, 10, 12 and 14, it is seen that when forced exhaust was used the oxidation rate of molybdenum increased with increasing temperature. A rapid increase was observed between 1400 and 1600°F, attributable to the effects

Jan 1, 1959

By K. H. Coats

This paper describes an approximate technique for handling the problem of percolation of evolved gas upwards through the oil column in computer simulation of natural depletion. This technique has been incorporated into a general model for simulating three-phase flow in one, two or three dimensions. The mathematical model for perfonning these calculations is described in detail in a separate article. 1 While vertical gas percolation occurs during natural depletion in a reservoir of any configuration, it is especially pronounced in the pinnacle reel or bioherm. The reel may have an areal extent less than one section with a thickness of up to 800 It. The upward percolation of evolved gas often limits the time step in calculations as little as one day. Using this small time step, computer expense for a single 30- to 40-year simulation on even a one-dimensional basis has exceeded 92,000. The method described here for handling the percolation allows time steps of 60 days or more (depending on reservoir size and production rate), resulting in a considerable reduction in computing expense. The method also allows calculations in which secondary gas caps build up in tight zones of the oil column below the main gas cap. The validity of the method is indicated in connection with an example pinnacle reef field. Calculated results using a 2-day time step (where the method in question is not needed and not invoked) are compared with results using the method and a 60-day time step. The comparison shows good agreement. Results from one- and two-dimensional simulations of the reef are presented along with the corresponding computing times on the CDC 6600 computer. A three-dimensional simulation was also performed and the required computing time is given. INTRODUCTION A general analysis for simulating three-dimensional, three-phase flow in reservoirs has been developed. 1 In applying this model to reservoirs undergoing natural depletion, a time-step restriction was encountered due to the flow of evolved gas upwards through the oil column and toward the gas cap. A remedy for this problem has been incorporated in the analysis and is described here. The time-step restriction is encountered only in calculations which include flow in the vertical or near vertical direction. The restriction occurs to some extent in reservoirs of any geometrical configuration, but it is especially pronounced in the pinnacle reef or bioherm where the ratio of thickness to areal extent is unusually large. This paper describes the problem, a method of handling it, incorporation of the method in the three-dimensional, three-phase model, and, finally, a test of the method's validity in an application to an example pinnacle reef reservoir. THE PROBLEM During the early stages of reservoir depletion, pressure falls below bubble point in progressively lower regions of the oil column. Continuing production results in evolution of dissoived gas throughout the oil column. This gas then percolates upwards toward the top of the reservoir. If the gas encounters a sufficiently low permeability zone in its travel upward, then it can accumulate and form a secondary gas cap. If no zones are encountered which are tight enough to hold gas against the gravity forces, then the gas travels on until it reaches the top of the sand or the main gas cap. Numerical simulation of multiphase flow in reservoirs is generally performed with time steps such that the flow of a fluid into or out of a block in one time step is a fraction (considerably less than one) of the total amount of that fluid present in the block. Use of a time step where the time step's

Jan 1, 1969

By J. J. Taber, W. K. Meyer

Experiments on consolidated sandstones have shown that a variety of conditions are responsible for the wide range of behavior observed when oil and water are displaced simultaneously by a solvent which is miscible with both. The type of displacement is influenced most strongly by the relation between the plait point of the ternary phase diagram and the composition path followed by the system as it achieves mis-cibility. Neglecting viscosity, the displacement becomes less efficient as the distance between the composition path and plait point is increased in either direction so that a very wide spectrum of displacements is possible with different alcohol, oil and brine systems. It is possible by choosing various composition paths as miscibility is achieved to exercise some control over the actual displacement mechanism. Control over the composition path is exercised by adding oil or water in specific amounts to the alcohol prior to its injection into the porous medium. This technique apparently makes it possible to obtain piston-like displacements with systems which are usually characterized by the efficient displacement of only one of the two phases i.e., either oil or water, while the other phase lags behind. However, the simultaneous displacement of oil and water is not as efficient as other miscible displacements at a similar mobility ratio. The evidence indicates that both oil and water "leak" into the alcohol "piston" in compensating amounts. With oils of low viscosities the displacement is inefficient because the low oil saturation in the stabilized bank causes oil to be trapped by water before miscibility is attained. INTRODUCTION The simultaneous displacement of oil and water by solvents such as alcohol has been investigated in the laboratory and in the field. The laboratorv workers investigating all-liquid miscible systems have recognized the great importance that the nature of the traingular phase diagram exerts on the efficiency of the miscible displacement. Gatlin and Slobod pointed out that displacement efficiency will be improved if miscibility can be retained for long periods and that this behavior tends to be followed if the applicable phase diagrams have very low binodal curves. In their unconsolidated sand tests the alcohol was considered an ideal miscible piston displacing both oil and water phases. Later workers have pointed out that an important feature of the phase diagram as far as oil recovery is concerned is the location of the plait point. This is particularly true in the case of consolidated Sandstone.3 Since the original discussion of this effect, the importance of plait-point location has been confirmed and discussed by other author The early workers394 recognized that the position of the plait point could be altered by changing the oil or the alcohol used in an experiment. In addition, recent work has demonstrated that the plait point can be shifted by altering the nature and concentration of dissolved salts in the aqueous phase. However, the entire scope of the relationship between displacement and plait point has not been discussed previously and a technique for changing the composition path as miscibility is achieved in a particular ternary system, i.e., oil, water and solvent, has not been demonstrated. * The importance of oil viscosity on the efficiency of oil displacement by alcohol has not previously been observed, probably because the range of viscosities used in earlier experiments was too restricted. It is the object of this paper to describe the relationships between the ternary phase diagram, fluid properties and the displacement achieved. A technique for controlling the nature of the displacement is also presented. THEORY AND DEFINITIONS PISTON-LIKE THEORY The theory of alcohol flooding has been discussed in some detail.2-4 The concept was advanced that

Jan 1, 1965

By Pablo Hadzeriga

Great Salt Lake brine was subjected, in laboratory scale, to conditions simulating solar evaporation. Solid phases and the variation in composition of the liquid phase throughout the potassium salts crystallization zone are presented. These experimental results are discussed and compare with stable equilibrium data of the quinary system Cl-, SO4, Na+, K+, Mg + + and H2O. The Great Salt Lake brine in Utah is a vast reserve of several potential chemicals which has attracted much attention in the recent past. From the standpoint of an ore reserve, it may be said that the lake contains a low grade ore which has to be concentrated by evaporation of water. Because of the fairly favorable weather conditions in the Great Salt Lake area, it seems reasonable to consider solar evaporation as an economical means of concentration. From the view of phase chemistry, the main constituents of Great Salt Lake brine make it belong to the five component system: C1-, SO4=, Na+, K+, Mg++ and H2O. Because of their low concentration, the presence of other elements may be regarded as having little effect on the equilibrium of the five main components. Equilibrium data for the quinary system of our interest has been available for many years. Using these data, it is possible to calculate how the brine of the lake will concentrate when subjected to solar evaporation. In practicing solar evaporation, the weather factor and supersaturation conditions cannot be ignored, but their introduction into calculations using equilibrium diagrams is almost an impossible task. With the experimental work presented in this paper, an attempt is made to compare the stable equilibrium data of the quinary system as applied to the case of the Great Salt Lake brine and the dynamic equilibrium when that brine is subjected to continuous solar evaporation. Sea water brine belongs to this quinary system when only the major constituents are considered. The study of this system has been carried on since the last decades of the nineteenth century. The reason for these intensive studies was to give a geological explanation to the underground potash deposits. AS a result, many theories were presented trying to relate the equilibrium data with the geological formation, paragenesis and metamorphism of these deposits. Two main approaches were followed for the equilibrium studies of this quinary system. One of them, and the best known to us, was the school started in Germany in the last century by J. H. Van't Hoff. The other one, which started about the same time, was the school of N. S. Kurnakov in Russia. Both approaches were different and as a consequence generated opposite theories about the geological formation of potash deposits. The Van't Hoff school studied the quinary system of sea water under careful laboratory control, resulting in stable phase diagrams. During these studies, Van't Hoff recognized the difficulties in crystallizing some double salts.' ". . . . we unexpectedly found that some compounds whose formation in the solutions under investigation was possible at 25°C, nevertheless totally failed to put in an appearance. These, not to mention the calcium salts, were leonite, MgSO4 . K2SO4 4 H2O; kainite, KC1-MgSO4 . 3 H2O; and kieserite, MgSO4 .H2O. Even exceedingly slow crystallization with the addition of the compounds themselves did not remove the condition of supersaturation in the case of these bodies." However, those salts (leonite, kainite, and kieserite) were included in the stable phase diagram at 25°C as shown in Fig. 1 using D'Ans data.3 The figure also shows the sequence of crystallization of the Great Salt Lake brine according to the stable diagram. In later studies by the Van't Hoff school, especially by D'Ans,3 Karsten,4 Autenrieth,5,6 attention

Jan 1, 1968

By James H. Boettcher, W. Durand Eppler

INTRODUCTION In the second quarter of 1979, Rapid Mining Co., Inc. ("Rapid") inquired whether Crocker National Bank ("CNB") would provide $4 million in term loan financing to help ("Dry Creek") acquire the outstanding shares of the Dry Creek Coal Company ("Dry Creek") in West Virginia. Prior to approaching CNB, Rapid had sought financing with the assistance of a financial advisor from a number of commercial banks without success. A summary of the initial terms requested by Rapid is shown in Table 1 compared with the actual terms on which the transaction closed. It is not difficult to note that the two sets of terms differ significantly. This is often the case when financing requests based on the expectations and vision of a mine developer are juxtaposed with more pragmatic requirements of a commercial bank. The "art" and fund of structuring financing plans for mining ventures (highly leveraged acquisitions or grass roots) comes in working with mine developers to arrive at a final financial structure that meets their objectives and constraints as well as those of the bank or other financial institutions providing much of the financing. Beginning with the terms requested by Rapid and ending with the terms that closed the transaction, this article briefly describes the process we went through with Rapid Mining. The Seller and Buyer The Dry Creek Coal Company was established in 1961, after its owner acquired the coal leases from Republic Steel. Republic has mined the primary coal seam from 1948-1961. Dry Creek was owned as a subchapter S corporation (i.e., for federal income tax purposes, income is taxed at the shareholder level) and had been run on a low key basis. Since the company had virtually no debt and limited cash needs, the owner produced primarily when rail cars were available and income was required. Output was therefore erratic as is shown in the top of Table II, but the result was a profitable little company with an attractive free cash position. Because the owner wished to retire and enjoy his wealth in a more readily spendable form, he had put the mine, with stated recoverable reserves of approximately 13 million tons, up for sale. In contrast, Rapid Coal's investors consisted of a number of investors of disparate financial situations. They had agreed upon a primary objective of income maximization and planned an annual production rate of 120,000 TPA which they and the current owner believed realizable. The Formulation of a Financing Structure Figure 1 presents a simplified overview of the sequence of steps taken in the financing process which lasted approximately three months from start to finish. Since banks see many requests for funding and considerble time is required to follow up on each, an important step was determining, after a brief review of the materials provided to us, whether the basic "eonomic entity" was viable. In this case, the size and quality of the reserves, the inherent operating cost characteristics, the sales arrangements, the management/labor situation and Rapid's principles all appeared to be sound enough to warrant investing the time necessary to do a thorough analysis of the project. Once this decision was made, the evaluation and analytic process shown in Figure 2 was initiated. The first and most fundamental concern of any banker is whether the loan will be paid back as scheduled from the cash flow generated by the project. The amount of debt relative to the owner's equity is of course crucial in such a determination. Before the debt/equity issue was addressed, however, a number of more qualitative factors had to be studied and if

Jan 1, 1985

By R. I. Jaffee, F. C. Holden, H. R. Ogden

Alpha solutes increase the strengths of Ti-Mn alloys through solid-solution strengthening. The substitutional a addition, aluminum, decreases, and the interstitial solutes, carbon and nitrogen, increase the rate of nucleation and growth of a from ß. The best combinations of properties of a-ß alloys are obtained when there is a sufficient quantity of a phase in the structure to dissolve the a solutes. OF the many different titanium-base alloy systems, the predominant alloy type is the a-ß alloy. The properties of the a-ß alloys are dependent on solid-solution strengthening and heat-treatment effects involving the a-ß ratio and transformation reactions. Another variable which influences the mechanical properties of a-ß alloys is the a-stabilizer content of the alloy. An a solute may be present as an intentional addition, such as aluminum, or as an impurity element, such as carbon, oxygen, or nitrogen. It is known that these a stabilizers, when added to titanium, form single-phase alloys which are not heat treatable but which obtain their strength from solid-solution strengthening. Thus, it would be expected that a additions to a-ß alloys would increase the strength of the alloys by solid-solution strengthening of the a phase. In addition, they would affect the transformation kinetics of the ß-to-a reactions and other processes based on the instability of the ß phase. The effects of heat treatment and structure on the mechanical properties of Ti-Mn alloys have been shown in a previous paper.6 This system offers a good base to demonstrate the effects of typical a solutes on the properties of a-ß alloys. The three a solutes described in this work are aluminum, representative of a substitutional a solute, nitrogen, representative of an interstitial a solute, and carbon, representative of an interstitial compound-forming element. The effects of heat treatment and microstructure on the properties of a alloys containing these three elements are described in concurrent publications. Some of these data are used for base-line points in several of the curves used for illustration herein. Experimental Procedures Iodide titanium was used as the base for all of the alloys studied in this work. The alloys were prepared as ½ lb ingots by double arc melting in an argon atmosphere. The ingots were forged to ¾ in. rounds, vacuum annealed for 6 hr at 900°C at a pressure of 10 ' to 10-5 mm of Hg to remove hydrogen, and hot swaged to 1/4 in. diam rod. After me- chanical descaling, test specimens were prepared for heat treatment. The alloys used in this study together with the fabrication temperatures are given in Table I. Heat treatments were done in argon. For the most part, the specimens were sealed in Vyeor capsules under a partial pressure of argon. Quenching was accomplished by breaking the capsule under water. Other cooling methods used included oil quench, argon cool (simulated air cool in an argon atmosphere), and furnace cool. The times for the various heat-treating temperatures are given in Table 11. The tests performed on the alloys consisted of tensile tests on ? in. diam specimens, hardness tests, and microimpact tests. Specimen sizes have been adequately described in a previous publication.' The micrographs presented in this paper were taken from specimens cut from the shoulders of broken tensile specimens. Final polishing was done with Linde B on a slow-speed wheel, and the specimens were etched with a 1½ HF — 3½ HNO, solution. Ti-N-Mn Alloys The transformation diagram and microstructures of the Ti-0.1 pct N-Mn alloys used in this investigation are given in Fig. 1. The effect of small nitrogen additions on the binary Ti-Mn diagram is to raise the ß-transus temperature with little effect on the a solubility of manganese. Also, as has been noted previously,' high manganese-content alloys containing nitrogen, when quenched from temperatures high in the ß field, contain a subgrain boundary phase which appears to be nitrogen-rich a. Marten-site is formed when alloys containing less than about

Jan 1, 1956

By R. F. Hehemann, D. J. Cometto, G. L. Houze

The w transformation in the Zr-Nb system was studied using X-ray diffraction, dilatometric, re-sistornetric, hardness, and metallographic techniques. w forms in a diffusionless, completely reaersible manner on quenching and in a diffusion-controlled manner- on aging. The temperature at which w begins to form on quenching was determined as a Junction of composition and was found to decrease with increasing solute content. w formed bv aging establishes a metastable equilibrium with an enriched ß phase. The ß/w + ß transus has been determined for this metastable equilibrium and employed to rationalize retrogression and reversion phenomena observed in these alloys. The decomposition mechanism is discussed in terms of a gradual or continuous transformation from ß to the w state. BETA- stabilizing alloying elements lower the MS temperature of the martensitic bcc (ß) to hcp (a') transformation in zirconium and titanium alloys. In certain titanium alloys, a lower symmetry modification of the martensitic structure, termed (a"), also has been reported.1,2 These martensitic transformations are suppressed when the amount of the ß-stabilizing element exceeds a critical level. However, the high-temperature ß phase cannot be quenched to room temperature without change. At alloy contents just above the critical level, |ß trans-forms to the w phase when cooled rapidly.3-6 The amount of w in quenched alloys is reduced by increasing alloy content, and this phase virtually disappears above a critical composition.5 In addition to the transformation during cooling, w also can be formed by aging ß at temperatures below approximately 500°C, and significant alloy enrichment of retained 13 accompanies the isothermal transformation.1-8 The structure of LC is closely related to that of the ß from which it forms.9-15 The bcc (ß) lattice can be generated using a hexagonal cell with three atoms located at (000) and ±(2/3, 1/3, 1/3). This cell has an axial ratio of 0.612 and is oriented with respect to the cubic cell such that (0001)H (111)C and [1120]H [101]C. Consequently, there are four possible orientations of the hexagonal cell, associated with the four (111) planes of the bee lattice. Formally w can be obtained from 0 by allowing the two atoms at the ±(2/3, 1/3, 1/3) positions to approach the coordinates ±(2/3, 1/3, 1/2) and there are four equally probable orientations of w for each 0 grain. In titanium alloys w retains the cubic axial ratio of 0.612" and hence also can be indexed as triply cubic, but this is not the case for aged Zr-Nb alloys where w is clearly hexagonal with an axial ratio of 0.622." The lattice parameters and atomic positions of w depend on thermal history and alloy content. The atomic positions (000), ±(2/3, 1/3, 1/2) provide reasonable agreement between calculated and observed diffracted intensities for w in the fully aged condition.10,14 In the quenched condition, on the other hand, the atoms appear to be displaced from the central plane12,13,15 and assume positions ±(2/3, 1/3, Z = 0.42-0.48) rather than ±(2/3, 1/3, 1/2). This results in a structure with trigonal rather than hexagonal symmetry. The readily detectable parameter and axial-ratio changes of w in Zr-Nb alloys make this system especially attractive for studying the structural changes that occur in the formation and aging of w. Particular attention in this investigation has been directed to the relationship between the structure of w in the quenched and aged conditions, and to certain aspects of the reaction kinetics. MATERIALS AND PROCEDURE Zr-5, 12, 17.5, and 25 pct Nb alloys were prepared by a double arc-melting practice, encased in stainless-steel cans and hot-rolled to 1/8-in.-thick sheet.* Charged weights have been employed for the niobium contents and interstitial analyses are reported in Table I. Dilatometric, X-ray diffraction (filtered CuK, and MoK, radiation), metallographic, and hardness techniques have been employed to follow the transformations during isothermal and quench-aging heat treatments. In quenched specimens, the electrical resistivity also was studied. Betatizing was conducted for 1 hr at 900°C. With the exception of the isothermal dilatometric studies, samples were

Jan 1, 1965

By Shiou-Chuan Sun

THIS paper presents the design and operation of a frothmeter capable of measuring the frothing characteristics of pine oils and other frothing reagents. The experimental data show that the froth-ability of pine oil is governed by: 1—rate of aeration, 2—time of aeration, 3—height of liquid column, 4—chemical composition of pine oil, 5—pH value of solution, 6—temperature of solution, and 7—concentration of pine oil in solution. The effect of mineral particles on the behavior of froth also was studied, and the results can be found in a separate paper.' The results also show that the relative froth-abilities of pine oils in the frothmeter generally correlate with those in actual flotation, provided that other factors are kept constant. In addition to pine oils, the other well-established flotation frothers were tested, and the results are included. In this paper, compressed air frothing is the frothing process performed by means of purified compressed air, whereas sucked air frothing is the frothing process accomplished by purified air sucked into the glass cylinder by a vacuum system. The term vacuum frothing denotes that froth was formed by degassing of the air-saturated liquid under a closed vacuum system. Apparatus The frothmeter, shown in Fig. 1, is capable of re-producibly measuring the volume and persistence of froth as well as the volume of air bubbles entrapped in the liquid and is capable of being used for compressed air frothing, sucked air frothing, and vacuum frothing. Fig. la shows that for compressed air frothing, the apparatus consists of an airflow regulating system, 1-3; a purifying and drying system, 4-8; a standardized flowmeter to measure the rate of airflow from zero to 500 cc per sec, 9; and a graduated glass cylinder, 13; equipped with an air regulating stopcock, 10; an air chamber, 11; and a fritted glass disk to produce froth, 12. The fritted glass disk, 5 cm in diam and 0.3 cm thick, has an average pore diameter of 85 to 145 microns. The pyrex glass cylinder has a uniform ID of 5.588 cm and an effective height of 63 cm. The inside cross-sectional area of the glass cylinder was calculated to be 24.53 sq cm, or 3.8 sq in. For sucked air frothing, Fig. lb shows that the apparatus for compressed air frothing is used again, with the following modifications: 1—compressed air and its regulating system, 1-3, are eliminated; and 2—a vacuum system, 16, equipped with a vapor trap, 15, and a vacuum manometer, 17, is added. The vacuum system can be either a water aspirator or a laboratory vacuum pump. Any desired rate of airflow can be drawn into the glass cylinder, 13, by adjusting the opening of the air regulating stopcock, 10. The sucked air stream is cleaned by the purifying and drying system, 4-8, before entering the glass cylinder, 13. When this setup is used for vacuum frothing, the air regulating stopcock is closed. The frothmeter has been used for almost 3 years and has proved to give reproducible results, as illustrated in Table I. With a magnifying glass and suitable illumination, the frothmeter also can be used to study the attachment of air bubbles to coarse mineral particles.' Experimental Procedures Except where otherwise stated, the data presented were established by means of the compressed air method. The volume and persistence of froth were recorded respectively at the end of 4 and 6 min of aeration at a constant rate of airflow of 29.3 cc per sec, which is equivalent to 71.6 cc per sq cm per min, or 462.6 cc per sq in. per min. The aqueous solution for each test, containing 1000 cc of distilled water and 19.2 ± 0.5 mg frothing reagent, was adjusted to a pH of 6.9 0.2. The volume of froth is expressed as cubic centimeter per square centimeter and is equivalent to the height of the froth column (the distance between the bottom and the meniscus of the froth). The volume of froth was obtained by multiplying the height of froth by the cross-sectional area of the glass cylinder, 24.53 sq cm. Before each test, the glass cylinder, 13, was cleaned thoroughly with jets of tap water, ethyl alcohol, tap water, cleaning solution, tap water, and finally distilled water. The cylinder with stopcock,

Jan 1, 1953

By Irving B. Cadoff, Alvin A. Machonis

The resistivity, Hall coefficient, Seebeck coefficient, and thermal conductivity were measured as a function of temperature for cation-rich alloy single crystals covering the composition range across the PbTe-SnTe system. Alloying of PbTe with up to 20 pct SnTe was found to have little effect on the energy gap. Above 20 pct SnTe the alloys were "p" type but below this range the sign could be varied by heat treatment. The lattice thermal resistivity of the compounds SnTe and PbTe is raised by alloying one with the other. Z values in the order the interesting values obtained. THE PbTe-SnTe system has several interesting features. For one, PbTe is a useful thermoelectric material and the possibility of improving its figure of merit by alloying with SnTe, an isomorphous compound, has been suggested since these pseudo-binary solid solutions generally have a more favorable ratio of electrical conductivity to thermal conductivity than either of the components.' Other interesting features relate to the conductivity mechanism, band structure, and stoichiometry of the compounds and their alloys. PbTe is a semiconductor with an energy gap of about 0.29 ev2 at room temperature whose conductivity sign and magnitude can be varied from "n" to "p" by controlling the proportion of lead and tellurium with respect to the stoichiometric ratio.3 Excess lead results in "n"-type conduction. SnTe is found to exist only as a "p"-type material of relatively high conductivity. This behavior is attributed to stoichiometric deviation by Brebrick4 but Sagar and Miller proposed that the behavior of SnTe must be due in part to the presence of an overlapped band. An investigation of alloys of this system, therefore, might give additional information which would permit one to evaluate which of the two proposals is the more appropriate one. Abrikosov et al.' studied the room-temperature electrical properties of these alloys and reported data for Seebeck coefficient and resistivity on poly-crystalline alloys. The present work is a more exhaustive survey of the PbTe-SnTe system. Re- sistivity, Hall coefficient, Seebeck coefficient, and thermal conductivity were measured over a wide temperature range for single crystals at 10-pct intervals of lead/tin ratio across the pseudobinary system. The relative concentration of tellurium was controlled so as to obtain metal-ion excesses in all cases. SAMPLE PREPARATION The crystals were prepared by melting elemental lead, tin, and tellurium in weighed proportions in evacuated Vycor capsules. The lead and tellurium were high-purity grades obtained from American Smelting & Refining Co. The tin was supplied by Comico. The proper calculated proportions of lead, tin, and tellurium were weighed and charged into prepared Vycor capsules prior to evacuation. The capsules were prepared from 15-mm Vycor tubing. A sharp point was worked on one end of the tube. A pyrolytic graphite coating was deposited on the Vycor walls by heating the tip to 800°C in an atmosphere of acetone-saturated argon. An additional coating of graphite was deposited on the pyrolytic coating from an Aquadag suspension. Above the coated tip the tube was reduced in diameter to form a constrictive neck. To avoid scratching the graphite coatings the charge was placed in the tube above the constriction. After a low-temperature bake, the evacuated capsule was sealed. On subsequent heating the charge melted down into the lower portion of the capsule. The crystals were grown by lowering the capsule through a Bridgman-Stockbarger furnace. The lowering rate was 1 in. per 8 hr. The upper portion of the furnace was set for 950°C and the lower portion for 800°C. In general the yield of single crystals was about 25 pct. The mixed compositions were, as expected, the most difficult to grow. The finished crystals were sectioned into 5/8-in. slices. The tip, end, and middle slices from each crystal were analyzed by X-ray fluorescence to determine the lead-to-tin ratio. The resulting values were used to plot a composition vs distance plot for each crystal. Slices were selected from each crystal, with the aid of the composition plots, to cover the complete range of compositions at 10-pct intervals. In general, the slices selected were taken from the seed end of the crystal where the longitudinal segregation (as determined from the X-ray fluorescence analysis) was a minimum. Laue single-crystal analysis and metallographic analysis was used to verify if a slice was single or polycrystal. Any grain boundaries were clearly visible in the as-cut and polished condition. In ad-

Jan 1, 1964

By Shiou-Chuan Sun

THIS paper presents the design and operation of a frothmeter capable of measuring the frothing characteristics of pine oils and other frothing reagents. The experimental data show that the froth-ability of pine oil is governed by: 1—rate of aeration, 2—time of aeration, 3—height of liquid column, 4—chemical composition of pine oil, 5—pH value of solution, 6—temperature of solution, and 7—concentration of pine oil in solution. The effect of mineral particles on the behavior of froth also was studied, and the results can be found in a separate paper.' The results also show that the relative froth-abilities of pine oils in the frothmeter generally correlate with those in actual flotation, provided that other factors are kept constant. In addition to pine oils, the other well-established flotation frothers were tested, and the results are included. In this paper, compressed air frothing is the frothing process performed by means of purified compressed air, whereas sucked air frothing is the frothing process accomplished by purified air sucked into the glass cylinder by a vacuum system. The term vacuum frothing denotes that froth was formed by degassing of the air-saturated liquid under a closed vacuum system. Apparatus The frothmeter, shown in Fig. 1, is capable of re-producibly measuring the volume and persistence of froth as well as the volume of air bubbles entrapped in the liquid and is capable of being used for compressed air frothing, sucked air frothing, and vacuum frothing. Fig. la shows that for compressed air frothing, the apparatus consists of an airflow regulating system, 1-3; a purifying and drying system, 4-8; a standardized flowmeter to measure the rate of airflow from zero to 500 cc per sec, 9; and a graduated glass cylinder, 13; equipped with an air regulating stopcock, 10; an air chamber, 11; and a fritted glass disk to produce froth, 12. The fritted glass disk, 5 cm in diam and 0.3 cm thick, has an average pore diameter of 85 to 145 microns. The pyrex glass cylinder has a uniform ID of 5.588 cm and an effective height of 63 cm. The inside cross-sectional area of the glass cylinder was calculated to be 24.53 sq cm, or 3.8 sq in. For sucked air frothing, Fig. lb shows that the apparatus for compressed air frothing is used again, with the following modifications: 1—compressed air and its regulating system, 1-3, are eliminated; and 2—a vacuum system, 16, equipped with a vapor trap, 15, and a vacuum manometer, 17, is added. The vacuum system can be either a water aspirator or a laboratory vacuum pump. Any desired rate of airflow can be drawn into the glass cylinder, 13, by adjusting the opening of the air regulating stopcock, 10. The sucked air stream is cleaned by the purifying and drying system, 4-8, before entering the glass cylinder, 13. When this setup is used for vacuum frothing, the air regulating stopcock is closed. The frothmeter has been used for almost 3 years and has proved to give reproducible results, as illustrated in Table I. With a magnifying glass and suitable illumination, the frothmeter also can be used to study the attachment of air bubbles to coarse mineral particles.' Experimental Procedures Except where otherwise stated, the data presented were established by means of the compressed air method. The volume and persistence of froth were recorded respectively at the end of 4 and 6 min of aeration at a constant rate of airflow of 29.3 cc per sec, which is equivalent to 71.6 cc per sq cm per min, or 462.6 cc per sq in. per min. The aqueous solution for each test, containing 1000 cc of distilled water and 19.2 ± 0.5 mg frothing reagent, was adjusted to a pH of 6.9 0.2. The volume of froth is expressed as cubic centimeter per square centimeter and is equivalent to the height of the froth column (the distance between the bottom and the meniscus of the froth). The volume of froth was obtained by multiplying the height of froth by the cross-sectional area of the glass cylinder, 24.53 sq cm. Before each test, the glass cylinder, 13, was cleaned thoroughly with jets of tap water, ethyl alcohol, tap water, cleaning solution, tap water, and finally distilled water. The cylinder with stopcock,

Jan 1, 1953

By E. F. Thomas

THE late George S. Rice was active in the inves--I- tigation of bumps, particularly in the last ten years of his career as chief mining engineer of the U. S. Bureau of Mines. Since most of his investigation was carried out in Great Britain, continental Europe, and—to a lesser extent—Canada, his thinking on prevention was influenced considerably by the experience of those countries. It is not surprising, therefore, that when he was called upon a few years before his retirement to investigate bumps in the U. S. and suggest ways to prevent them, he turned to longwall mining. A longwall method had been most successful in combating the bump hazard in mining coal under deep cover, especially in Great Britain, but the prevailing method there at the time was advancing longwall mining, which he knew was uneconomical under U. S. mining conditions. For this reason he proposed a modified retreating longwall system that he believed included the best features of the advancing method. As brought out by Rice,' if the cover is 2000 ft and 50 pct of the coal is extracted, the static load on the remaining pillars will be about 4000 psi, which exceeds the ultimate crushing strength in most instances. If the pillar coal is overloaded before a pillar line is established, then the abutment zone preceding a line of extraction is no place to split pillars or extract them by any method other than an open-end system. Rice therefore advocated open-end mining, preferably by longwall, but he was willing to compromise with long-face mining if the longwall method was not acceptable. Rice's system was put into operation in a mine in Harlan County, Kentucky,3 but subsequent experience has shown that it did not take into account two important factors—avoidance of pillar-line points and maintenance of adequate development in advance of the pillar-line abutment area. For ten years after Rice's retirement the USBM did little investigation and research on bumps, chiefly because so few were occurring that there was not much cause for alarm. But in 1951 there were three occurrences involving fatal injuries, and the Bureau began a statistical survey in that year. C. T. Holland, head of the department of mines at Virginia Polytechnic Institute, was retained as a consultant. The resulting study' of 117 case histories brought out these important conclusions: 1) Almost invariably the bump occurred in a locality affected by the abutment zones of one or more pillar lines. 2) In most cases the locality of the bump was influenced by the abutment zones of more than one pillar line. The term pillar-line point has been used for many years in the Appalachian region for such a situation. Point is used in the geographical rather than the mathematical sense. 3) In pillar-line extraction the following practices are safest in preventing bumps: a. The mine layout should provide for pillars of uniform size and shape along the extraction line. b. The mine layout should be planned so that no development need be done in the abutment zone of a pillar line. c. The layout should permit open-end extraction of pillar lines from the next goaf, so that it will not be necessary to resort to pocket mining, splitting pillars, or any practice that will involve driving in the direction of the goaf within the abutment zone. d. Pillars should be large enough to support area without undue roof and floor convergence before establishment of a pillar line. These are, of course, generalities, and while they are useful in laying out areas where bumps can be expected, they are of limited help in many mines that were committed to a system of mining before it was realized that they were subject to bumps. Under such conditions it becomes necessary to choose between the following alternatives: 1) Abandon the territory, except for pillars that offer no extraction problems. 2) Through experience select the pillars that are most heavily loaded, and, by augering, induce bumps from a safe vantage point so that impinged loads are relieved. This method was first developed at the Gary, W. Va. mines of U. S. Steel Corp. and later adapted to mining thick coal beds at Kaiser Steel's Sunnyside mine in Utah. No scientific method is available to determine where to drill within a loaded pillar. Although this method of unloading has worked very successfully at Gary—with one exception—

Jan 1, 1959

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as on control of furnace practice. This chapter deals only with those raw materials of the basic open-hearth process which are important in determining the composition of the steel or slag. They are the metallic charge, oxygen-bearing materials, fluxes, and alloying and deoxidizing additions. Refractories, which may also affect the slag composition, are discussed in the previous chapter. Wide variations are possible in the type and composition of charged materials, but in all cases certain fundamental relationships among the elements of the charge must be maintained. Since the process consists essentially of refinement by oxidation of undesired elements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters II and VII). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme would be the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not subject to oxidation or other reactions resulting in their elimination, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type would be found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should below in copper, or a sufficiently high ratio of pig iron to scrap should be charged to dilute the copper from the scrap, so that the average copper content of the melt will be below the required maximum.

Jan 1, 1944

By R. L. Bell, T. G. Langdon

A technique was developed- for determining the grain strain, and hence the grain boundary sliding contribution, occurring during the high- temperature creep of a magnesium alloy, from the distortion of a grid photographically printed on the specimen surface. The results were compared with those obtained from measurements of grain shape, both at the surface and interrwlly, and it was concluded that the grain shape technique may substantially underestimate the grain strain and overestimate the sliding contribution due to the tendency for migration to spheroidize the grains. ALTHOUGH a considerable volume of work has been published on the role of grain boundary sliding in high-temperature creep, many of the estimates of Egb (the contribution of grain boundary sliding to the total strain) have been in error due to the use of incorrect formulas or inadequate averaging procedures.' One of the most easy and convenient measurements from which to compute Egb is that of v, the step normal to the surface where a grain boundary is incident. Unfortunately, this parameter is also the one associated with the treatest number of pitfalls. Values of v have been used to calculate Egb from the equation: egb =knrVr [1] where k is a geometrical averaging factor, n is the number of grains per unit length before deformation, v is the average value of v, and the subscript ,r denotes the procedure of averaging along a number of randomly directed lines. If the dependence of sliding on stress were assumed, it would be possible, in principle, to calculate k from the known distribution of angles between boundaries and the surface. This in itself is difficult because the distribution depends on the history of the surface,' but the problem is even further complicated by the fact that v depends on other factors such as the unbalanced pressure from subsurface grains.3 However, the great simplicity of the measurement procedure for v makes it highly desirable that this problem of k determination should be overcome. In the present experiments, this was achieved by the use of an indirect empirical method in which the grain strain, eg, at the surface was determined by the use of a photographically printed grid. The assumption here is that the total strain, et, is simply the sum of that due to grain boundary sliding, egb, and that due to slip or other processes within the grains, eg. SO that: Et = Eg + Egb [2] Thus k is given by: In practice, it is customary to indicate the importance of sliding by expressing it as a percentage of the total creep strain; this quantity is termed y (= 100Egb/Et). The determination of Eg from a printed grid within the grains avoids the difficulties due to boundary migration which should be considered when the grain strain is calculated from measurements of the average grain shape before and after deformation. As first pointed out by Rachinger,4,5 however, this latter technique has the particular advantage that it can also be applied in the interior of a polycrystal. Recently, several workers have produced evidence on a variety of materials6-'' to support the observation, first made by Rachinger on aluminum,4,5 that 7 can be very high, 70 to 100 pct, in the interior, even when the surface value, determined from boundary offsets, is very much lower.10'11 Although there have been criticisms both of the shortcomings of the grain shape technique'' and of the different procedures used to determine y at the surface,' it seemed important to check whether measurements of sliding by grain shape gave values of y which were truly representative of the material. In the present experiments, grain shape measurements were therefore made both at the surface and in the interior for comparison with one another and with the independent measurements of grain strain using the surface grid technique. EXPERIMENTAL TECHNIQUES The material used in this investigation was Magnox AL80, a Mg-0.78 wt pct A1 alloy supplied by Magnesium Elektron Ltd., Manchester. Tensile specimens, about 7 cm in length, were prepared from a 1.27-cm-diam rod, with two parallel longitudinal flat faces each approximately 3 cm in length. The specimens were annealed for 2 hr in an oxygen-free capsule, at temperatures in the range 430° to 540°C, to give varying grain sizes, and, prior to testing, the grain size of each was carefully determined using the linear intercept method. This revealed that the grains were elongated -0.5 to 5 pct in the longitudinal direction. Testing was carried out in Dennison Model T47E machines under constant load at temperatures in the range 150" to 300°C. At temperatures of 200°C and below, tests were conducted in air with the polished flat faces coated with a thin film of silicone oil to prevent oxidation; at higher temperatures, an argon atmosphere was used. To determine v,, each test was interrupted at regular increments of strain and the specimen removed from the machine. At the lower strains, when v, was less than about 1 pm, measurements were taken on a Zeiss Linnik interference microscope;

Jan 1, 1969

By W. Hurst, R. E. Leeser, W. C. Goodson

Three aspects of gas deliverability are presented in this paper. The first treats with the gas deliverability or availability of a normal depletion-type dry gas field. Such encompasses not only the period of stabilized constant rate, but more so, the "tailings" when a fixed abandonment pressure is reached and the rate by necessity must decline. A comprehensive work plot is offered, developed from mathematics herein included, that removes the triai-and-errnr computations that attended such undertakings in the past. The second part treats with the discount factor of the open flow potential constant from what is observed initially in testing a gas well to what is evidenced when stabilization is reached. This prevails in tight formations, such as the Kansas Hugoton field which is offered as the example. The means of establishing this factor are pressure build-up curves which, as sustained by analytical deductions, reproduce this entire period of transient flow under conditions of a constant rate influx. Finally, what is offered in this paper is the deliverability performance of an exceedingly rich gas condensate field producing from a tight formation. The example shown is the Knox Bromide field in Oklahoma, producing from the Bromide formations. The results are ominous, showing early reduction in permeability to gas pow, due to the retrograde condensate forming in the pore space, with the attending early logging-up of these wells. The analytics of lowered permeability are incorporated in the gas deliverability formula along with the PVT data that gives the increased condensate liquid saturation as the gas flows to the well bore. This paper would not be complete without a critique oflered at the end. With the many gas wells now in production and those that have completed their life, there has been no factual information collected by any source as to what constitutes that permeability range where a gas well would be unimpaired in its gas deliverability by the presence of rich condensate content, and the lowered range where such would be harmful. This question confronts all producers. INTRODUCTION Various aspects of gas deliverability are presented in this paper that includes depletion-type reservoirs, deteriora- tion factor of the gas deliverability constant, and the performance of a rich gas condensate reservoir producing from a tight sand. With respect to the presentation of gas deliverability and its tailings for depletion-type gas reservoirs, one notes that this is essentially the information offered by every gas transmission company and producer appearing before the Federal Power Commission for Letters of Conveyance in the dedication of reserves. In the ordinary procedure, as many engage upon this study, trial-and-error calculations are included, particularly as apply to the tailings. For many years one of the writers has employed mathematical analyses to perform this step and avoid the complexities so associated. In the preparation of this paper these analyses have been amplified to include any slope n for the open flow potential relationship for which the tailings can be determined from Fig. 1. With reference to the deterioration or discount factor of the open flow potential constant as such occurs in the gas deliverability formula, this for the most part has been an unexplored subject. Although the issue first appeared in the Kansas Hugoton field, where such was surmised but only recently resolved, this situation of a deterioration of the gas deliverability constant can occur wherever dry gas production from a tight sand is encountered. The first concerted attacks upon this problem were the presentations of Hurst' and Goodson' before the Kansas Corporation Commission to show that transient fluid flow and unsteady-state flow formulas prevailed. This was amplified later before the Federal Power Commission3 to show that this deterioration factor could be identified from pressure build-up curves. This has been reported by McMahon.4 Its importance to the industry merits the review of these essential features in completing the program on the aspects of gas deliverability. Finally, as illustrated here, for a low permeability formation such as the Knox Bromide field where the gas is rich, representing some 165 bbl of condensate per MMcf of effluent gas, the gas deliverability can be of limited extent in the life of the field, leaving substantial amounts of condensate and gas unrecovered. In cases such as this, gas cycling is mandatory. This is particularly revealed by the fluid mechanics introduced here, employing factual field as well as laboratory data, to show this-restriction upon gas deliverability. PRESSURE DEPLETION What will now be offered is the study of gas deliver-

By Irving B. Cadoff, Ernest Levine

The crack formation and propagation in the single -phase Cu-4 pct Ag alloys were studied. The alloys were loaded in mercury to various stress levels, the mercury was removed, and the specimen examined for cracks. Cracks were found to develop below the fracture stress; the frequency of such cracks increased with increasing stress level. Some cracks were nmpropagative. Fracture in mercury was found to occur by the link-up of cracks formed at various stress levels rather than by the growth and propagation of a single crack. If the mercury environment is removed prior to a critical amount of crack formation, then continued loading results in ductile fracture. The appearance of the cracks at selected grain boundaries is related to the relative orientation of the boundaries, as are the propaga-tive characteristics of the crack. The mercury interaction appears to be one of lowering the strength of the metal-metal bonds in the high-stress area of the grain boundary. GRIFFITH'S microcrack theory1 proposed a critical crack size above which a crack in an elastic material grows with decreasing energy at a stress of From his theory it was proposed that the presence of a liquid tends to lower the surface energy of the microcrack faces2 leading to a decrease in the critical crack size necessary for spontaneous fracture propagation. stroh3 proposed that the stress concentration at a grain boundary due to pile-up may initiate a microcrack at the grain boundary. petch4 and Stroh5 evaluated the stress distribution at the head of a pile-up in a polycrystal-line material and deduced that the critical crack size and hence of is dependent on the grain size. Experimental verification of this dependence was found by petch6 for hydrogen embrittlement of steel. Studies in stress-corrosion cracking7 have provided a picture of fracture which shows that initial separations occur in a scattered, independent fashion in regions of high tensile stress. A minimum or threshold stress is necessary to produce a sufficient stress concentration to initiate frac- ture. These separations join up to form a crack. The extension of fracture is largely discontinuous and consists of a joining up of cracks. In recent worka evidence of this scattered crack network was found in a Cu-Ag alloy embrittled by mercury. For the Cu alloy-Hg couple, the crack path has also been found to be dependent on the orientation of adjacent grains, and with the addition of zinc to mercury a reduction in embrittlement along with a change in fracture morphology was found.9 In this present study, a mercury-dewetting method was used to observe crack initiation and fracture morphology when a Cu-4 pct Ag alloy is deformed in mercury and Hg-Zn solutions. PROCEDURE Specimens of Cu-4 pct Ag were prepared as in previous crack-path studies.' The specimens were heated at 770°C for 24 hr and water-quenched Tension tests using a table-model Instron were carried out in mercury and in various concentrations of Hg-Zn. Loading was in steps up to the fracture stress, with the load being removed and the specimen examined for surface cracks at each step. The specimens were dewetted after each load to permit examination of the surface structure and rewetted prior to continued loading. The specimens were wetted by electro polish ing in phosphoric acid, rinsing in alcohol, and then immersing in a pool of mercury. Dewetting was accomplished by flame heating the specimen for 30 sec in a vacuum. Some surface contamination was found, but not enough to obscure crack configurations and grain boundaries. RESULTS Fracture Characteristics in Mercury. Fig. 1 is a stress-strain curve showing the progressive step-wise loading of the specimen. As may be seen from the graph, the first position stopped at a is at a stress 5000 psi below the expected fracture stress of 25,000 psi. Examination of the specimen after removal of mercury showed only one crack. The appearance of this crack at a stress far below the fracture stress of this alloy in mercury did not affect the stress-strain curve in any manner. The specimen was then recoated with mercury and deformation was continued (curve b, Fig. 1) raising the stress by 4000 psi, and the same procedure re~eated. The initial crack was located and appeared as in Fig. 2 (crack lb). In this figure the crack is

Jan 1, 1964

By C. Zener, J. H. Hollomon

IT Is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect o rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. EARLIER INVESTIGATIONS A clear analysis of the conditions necessary for plastic flow and for fracture was first given by Ludwik,1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis, both a flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracture is less than the flow stress and ductile if the reverse is true. According to Ludwik's analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence or now stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The. curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated' by the authors. According to this principle of equivalence, strain rate E and temperature T affect the flow stress only through a single parameter p of the form: p = EeQ/RT [I] In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. Combinations of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944