Search Documents

By K. J. Anusavice, R. T. DeHoff, A. G. Guy, T. B. Lindemer

As one oi the approacizes to understanding multicorn-ponent dimsion, an expevinzental sturly is being jnade of tracer diffusion in the copper corner of the CLI-Ni-Zn syste?n, out to 30 at. pct each of nickel and zinc, and in the 150°C range oJ temperature just below tlze solidts te?rlperature. The reslts obtained using the Znm isotope are reported heve, while studies with nickel and copper isotopes are planned for a future paper. The fifteen alloys investigated were melted in sealed wear lubes, sroaged, homogenized, and then analyzed, using the conventional isotope-plating plus lathe- sectiorzing teclzniqlte. The data obtaiued show that the difJusion coeflcient of the zinc isotope increases titlz increase in zinc content, and decreases t'itlz incease in nickel content. The correlation xith solidus temperature is particularly strong. Diffirsiui-ties ranged fro u sq cm per sec nt tlze Iiigh-zinc, low-nickel compositions. The activation energy /or tracer diffusion ravied j.or 31.000 to 54,000 calper mole. It is now generally recognized that diffusion data and theories are needed for multicomponent systems, where extensive practical developments and even some theoretical studies have already been made. For example, much recent work on precipitation from solid solution has been concerned with ternary solid solutions such as A-M-Z' while Zener relaxation has been studied on Au-Ag-Zn alloys,' although adequate diffusion data are available for neither of these systems. Actually, the only ternary systems for which systematic diffusion studies have been begun, in addi- tion to the one reported here, are CO-i-cr3 and Cu-A-Au. Since the theory of multicomponent diffusion is still in the stage of active development5 it is important to distinguish the various kinds of diffusion data that can be determined. An oversimplified approach, widely used prior to 1950, was to determine the influence of a third element, such as nickel, on the diffusion behavior of a binary alloy, such as CU-Z. Later it was recognized7 that four diffusion coefficients can be used to describe ordinary interdiffusion in a ternary system, while as many as six coefficients may be required to include the Kirkendall effect. It is likely that the number of independent coefficients will be shown to be less than four and six, respectively, through the application of the thermodynamics of irreversible processes.5 The simplest type of diffusion in a multicomponent system is tracer diffusion, since each component is characterized by its own tracer-diffusion coefficient in an alloy of a given composition. Thus, in a ternary alloy there are three tracer-diffusion coefficients, each a function of composition and temperature. The present research program is a study of tracer diffusion in the copper corner of the Cu-Ni-Zn system out to 30 at. pct each of Ni and Zn in a 150°C range of temperature just below the solidus temperature. The

Jan 1, 1967

By Robert E. Green

Formulae are given for calculating the modes of wave propagation in a single-crystdl specimen possessing a given crystallographic orientation. Such calculations lead to determination of the orientation factor appearing in the Granato-Lucke theory for the attenuation of these waves due to dislocation damping. A detailed treatment is given for the case of an aluminum crystal possessing the orientation having a maximum Schmid fac -tor of 0.5. FOR a number of years the attenuation of ultrasonic waves propagating in metals has been used to investigate various phenomena causing internal friction.Most of the experiments were performed on polycrystalline test specimens and the waves were assumed to be propagating in an isotopic medium. However Alers 6 in 1955 and more recently Hikata et at. Chiao and Gordon,8 and Swanson and Green 10 have used measurements of attenuation of ultrasonic waves to study internal-friction changes in single crystals. These authors were concerned with the energy losses experienced by the ultrasonic waves due to dislocation motion induced by plastic deformation of the crystals. Alers measured the attenuation of 7 mc per sec ultrasonic pulses propagating in zinc single crystals before, during, and after plastic deformation. Simultaneously he measured the time-dependent plastic strain at constant stress in order to study the correlation between this strain and attenuation. The crystals were oriented in such a way that the applied stress provided a direct shear on the slip plane, thus causing the deformation to proceed by slip on this plane. At the same time the high-frequency sound pulses were sent through the crystal perpendicular to the slip plane. He found that the attenuation of transverse waves, the stress vectors of which lie in the slip plane, was very sensitive to the deformation. The polarization of the particle displacements, associated with these waves, relative to the applied static shear stress, and hence the direction of slip, had no obvious effect on the results. The attenuation of longitudinal waves was affected by the deformation only when the slip plane was not perpendicular to the propagation direction. This indicated that the attenuation was caused by dislocations introduced by the deformation and moving only in the slip plane. Hikata et al. made simultaneous measurements of attenuation, velocity changes, and stress-strain relations on aluminum single crystals deformed in tension. Both longitudinal and shear waves were used, at frequencies of 10 and 13 mc per sec. They placed emphasis on the choice of propagation modes and polarization of the ultrasonic waves, such that interactions between these waves and dislocations on selected slip systems could be investigated. They also selected specimens possessing specific crys-tallographic orientations, which allowed investigation as a function of the number of equally favored slip systems under the applied stress. They found that, for symmetrical orientations, the change of attenuation decreases with the increasing number of equally favored slip systems, i.e., in the order

Jan 1, 1964

By J. R. Johanson

With the continuing development of automatic operations, it is important that reliable discharge rates through hoppers and bins be obtained for bulk solids. In most applications a feeder is used to control the feed rate. The selection of this feeder size is usually based on the rated ability of the feeder to move material without regard to the capability of the material to flow through the opening in the hopper onto the feeder. The dis charge rate through a given hopper opening may vary from zero to a theoretical maximum depending on the flow properties of the material. This paper presents an equation for the maximum discharge rate for a bulk material as a function of the hopper shape, the opening size and the flow properties of the material. Discharge-rate tests on various materials indicate good agreement with calculated values for opening sizes from a fraction of an inch to several feet. As part of a program to develop improved design criteria for bulk storage and handling facilities, a specific study of the methods involved in calculating the rate of discharge of bulk solids from hoppers and bins has been made. This study is closely related to earlier work done on the prevention of flow problems through the choice of proper design geometry of hoppers and bins1. The present paper is an extension of this earlier work, and therefore many of the concepts previously derived and explained will be used without explanation. Two types of flow will be considered: plane-strain flow in a wedge-shaped hopper and axial-symmetry flow in a conical hopper. The literature contains many studies on discharge rate for regular-shaped dry particles2*3 such as glass beads, lead shot and coarse dry sand. However, the work is empirical in nature, and it is difficult to extrapolate the given information to apply to moist, sticky materials typical of many industries. Some studies4 have shown a decrease in discharge rate with an increased moisture content of the material. However, no attempt was made to correlate the discharge rate with moisture. The method of calculating discharge rate presented in this paper was derived analytically from the basic knowledge of the flow of frictional, cohesive, granular solids, The equation includes the effect of material cohesion (stickiness), hopper configuration, opening size and bulk density of the material. THEORETICAL WORK The basic assumptions made in deriving the discharge rate equation are as follows: 1) The material is a frictional, cohesive, granular solid. 2) The flow is considered continuous and without significant density change. 3) The material at the hopper opening forms a continuously failing arch that is in dynamic equilibrium. 4) The strength of the material in the arch, which must be overcome for the arch to fail, is caused by the pressure in the flowing mass near the hopper opening. 5) This pressure at the hopper opening can be calculated5. If we consider the dynamic equilibrium of an arch of uniform thickness such as that shown in Fig. 1,

Jan 1, 1965

By B. K. Larkin, H. K. van Poollen, H. C. Bixel

A detailed treatment is given of the transient pressure behavior of a well located near a linear discontinuity. On either side of the discontinuity, the values of permeability, viscosity, compressibility, and porosity are uniform, but may be different from those on the other side of the discontinuity. These results generalize previously published works which assumed the permeability ratio for media on different sides of the discontinuity was zero, one, or infinity. One application of this material would be to facilitate detection of facies changes or fluid-fluid contacts by transient testing. Solutions, presented graphically, show pressure decline for constant rate fluid production. The range of variables examined includes dimensionless time from 0.1 to 100, rnohility ratio from 0.001 to 1000 and specific compressibility ratio from 0.001 to 1000. For dimensionless tinze less than 0.4, the pressure behavior is essentially that of a well in an infinite reservoir. Thus, reservoir properties near the well may be estimated in the usual manner. Using an overlay technique to match an experimental curve with one of the theoretical curves, it is possible to estimate the distance to a discontinuity by substituting the actual time t and the corresponding dimensionless time , at which a match occurs into the equation where is the diffusivity near the well, and may be estimated from data taken at early time. Because of both the complexity of the solutions and limited computer facilities, well interference problems were not examined extensively. However, it was found that well interference may be masked by the discontinuity in some cases. By superposition of the results of constant rate fluid production, the problenz of pressure buildup may be treated. Such results show that for early shut-in times correct values for the transnzissibility are obtained from conventional semilog plotting. However, erroneous values of the static reservoir pressure are obtained unless data at large shut-in times are taken. INTRODUCTION Transient well testing has yielded estimates of such reservoir parameters as static reservoir pressure, permeability. porosity, and well bore effects. In most tests, it was assumed that the reservoirs were homogeneous and iso-tropic. Anisotropic media' and radial discontinuities were considered.'.' Various studies have been made on multiple-layer reservoirs." ' Linear discontinuities have been described for problems of one-dimensional flow.' In the present paper, a mathematical treatment is given for a well located near a linear discontinuity in an otherwise infinite medium (see Fig. 1). An actual reservoir analogy would be a well in a relatively thin reservoir near a fluid-fluid contact, or a well located in a reservoir exhibiting a sudden change in rock and formation characteristics, such as thickness, porosity, or permeability. A sudden change in porosity or permeability may be caused by clay fill or other types of facies changes. Sudden thickness changes niay be the result of such geological formations as buried shore lines and channel deposits. In otherwise uniform formations, a linear discontinuity may be caused by fluid-fluid interfaces such as oil-water contacts. 3s-oil contacts, or gas-water contacts.

By F. Keller, J. D. Edwards

The anodic treatment of aluminum presents problems of scientific as well as of commercial interest.l-3 Of particular interest is the fact that, during the anodic oxidation process, the oxide continues to form at the metal-oxide interface under any oxide previously formed. This has led to speculation as to the mechanism involved in the formation of the relatively thick oxide coatings that are used commercially for decorative or protective purposes. Furthermore, the ability of certain types of oxide coatings to adsorb dyes and other substances has stimulated research to determine the actual structure of these adsorptive coatings. It has been found that anodic oxide coatings on aluminum are composed essentially of aluminum oxide. They are formed by the action of oxygen ions penetrating to the metal surface during the electrolytic oxidation treatment. These coatings can be formed in a number of different electrolytes, as for example, those which contain sulphuric acid, chromic acid, oxalic acid, or boric acid. These are the commonest and most useful electrolytes employed commercially. Except for certain specific conditions of formation, the coatings in general have been found to be amorphous alumina, as far as can be determined by X-ray or electron-diffraction methods. Anodic oxidation processes can be arranged in three rather general classes if they are grouped in relation to the solvent action of the electrolyte on the coating.4 In the first class, the electrolyte has little or no solvent action on the coating that is formed. In general, coatings produced under such circumstances are nonporous and non-adsorptive. In the second class, the electrolyte exerts an appreciable solvent action on the coating. These coatings are porous and adsorptive. Finally, for the third class, the electrolyte tends to dissolve the coating about as rapidly as it is formed. This action produces electrolytic brightening or anodic polishing of the aluminum surface and at most leaves only a very thin film of oxide. The nonporous and nonadsorptive type of oxide film is represented by the coatings that are formed when solutions of boric acid are employed as the electrolyte. It is especially significant that these impervious films are formed in electrolytes that exert little or no solvent action on the coating. Where a boric acid electrolyte is used, the coating tends to form rapidly, with the result that the flow of current is soon reduced to substantially zero. This indicates that the growth of the coating has stopped. As a rule, the thickness of the coating is roughly proportional to the voltage employed for formation and the coatings of this type are exceedingly thin. In an electrolyte of this type, the coating has a high resistance when the aluminum is made anode; consequently, any current that may flow (leakage current) is very

Jan 1, 1944

By F. Keller, J. D. Edwards

The anodic treatment of aluminum presents problems of scientific as well as of commercial interest.l-3 Of particular interest is the fact that, during the anodic oxidation process, the oxide continues to form at the metal-oxide interface under any oxide previously formed. This has led to speculation as to the mechanism involved in the formation of the relatively thick oxide coatings that are used commercially for decorative or protective purposes. Furthermore, the ability of certain types of oxide coatings to adsorb dyes and other substances has stimulated research to determine the actual structure of these adsorptive coatings. It has been found that anodic oxide coatings on aluminum are composed essentially of aluminum oxide. They are formed by the action of oxygen ions penetrating to the metal surface during the electrolytic oxidation treatment. These coatings can be formed in a number of different electrolytes, as for example, those which contain sulphuric acid, chromic acid, oxalic acid, or boric acid. These are the commonest and most useful electrolytes employed commercially. Except for certain specific conditions of formation, the coatings in general have been found to be amorphous alumina, as far as can be determined by X-ray or electron-diffraction methods. Anodic oxidation processes can be arranged in three rather general classes if they are grouped in relation to the solvent action of the electrolyte on the coating.4 In the first class, the electrolyte has little or no solvent action on the coating that is formed. In general, coatings produced under such circumstances are nonporous and non-adsorptive. In the second class, the electrolyte exerts an appreciable solvent action on the coating. These coatings are porous and adsorptive. Finally, for the third class, the electrolyte tends to dissolve the coating about as rapidly as it is formed. This action produces electrolytic brightening or anodic polishing of the aluminum surface and at most leaves only a very thin film of oxide. The nonporous and nonadsorptive type of oxide film is represented by the coatings that are formed when solutions of boric acid are employed as the electrolyte. It is especially significant that these impervious films are formed in electrolytes that exert little or no solvent action on the coating. Where a boric acid electrolyte is used, the coating tends to form rapidly, with the result that the flow of current is soon reduced to substantially zero. This indicates that the growth of the coating has stopped. As a rule, the thickness of the coating is roughly proportional to the voltage employed for formation and the coatings of this type are exceedingly thin. In an electrolyte of this type, the coating has a high resistance when the aluminum is made anode; consequently, any current that may flow (leakage current) is very

Jan 1, 1944

By John Mullen

Impingers TWO types of midget impinger apparatus are used at Climax. The Mine Safety Appliances Company's midget impinger (MSA) and the Climax Molybdenum Company's midget impinger (CMC) (Fig. I). The Leiman Brother's No. 25, positive displacement pump is used in the CMC impinger instead of the four-cylinder radial pump that is used in the MSA impinger. With the MSA apparatus it is possible to obtain the proper vacuum by adjusting the needle valve on the vacuum chamber, while with the CMC impinger the proper vacuum is obtained by varying the rate at which the pump is cranked. The Leiman Brother's No. 25 pump is built to displace 0.1 cu. ft. of air per min. when operated at 145 r.p.m. In the CMC impinger this pump is so geared that the required crank speed is approximately 59 r.p.m. Both types of impinger apparatus are equipped with a water gauge mounted on top of the case and they are calibrated and operated in reference to the gauge. The MSA impinger flasks and nozzles are used with both types. Calibrating Impingers A calibrated precision Sargent wet-test meter (Fig. 2) is used in calibrating the impinger apparatus. The apparatus is set up as for taking a sample in the field, except that the hose from the outlet side of the meter is attached to the impinger nozzle. One revolution of the large hand of the meter indicates 0.1 cu. ft. of air displaced. The impinger pump is cranked for one minute, therefore, at a rate that will cause the large hand of the meter to make one revolution. The gauge reading is noted, then the impinger is cranked at this rate for 10 min. and is checked for error. If the meter indicates that more or less than I cu. ft. of air has been displaced, the impinger must be cranked—ither slower or faster according to the error—for another 10 min. and again checked for error. This operation is repeated until the proper gauge reading for a sampling rate of 0.1 cu. ft. per min. has been determined. This gauge reading is used in all sampling operations until the impinger is again calibrated. An impinger is calibrated at least twice each week. MlCROPROJECTOR A Bausch and Lomb model B micro-projector is used (Fig. 3). It consists of a substantial metal base supporting the light source and a microscope. Illumination is provided by a Bausch and Lomb 4.5-amp. arc lamp with mechanical feed. A glass water cell filled with a heat-absorbing and color-filter solution is placed between the arc lamp and the microscope. Two types of solution have been found satisfactory— a 2 per cent solution of copper sulphate or a 2 per cent solution of picric acid and distilled water. This percentage may be varied to give the desired color to the light reflected upon the screen. Any standard microscope may be used. A Bausch and Lomb microscope with

Jan 1, 1946

By H. H. Taft

The mining possibilities of the volcanic area south of Bel-mont, Nye county, Nevada, have long been known. Some of the old-time prospectors knew that gold existed there. Its remoteness from any source of supplies, its long distances from water, the absence of game, and more, perhaps, the lack of grass for animals to subsist upon, has made this an unattractive region in which to search for mines. The decline of the Comstock mines, the exhaustion of sundry large and rich ore-bodies, the high cost of mining, marketing, and, particularly, the ruinously high freight-charges upon refractory ore that had to be shipped to distant smelters, have kept investors out of Nevada for the last few gears; and mining people have hardly yet awakened to the importance of To-nopah, Goldfield, and perhaps the newer and less developed districts. The discovery of Tonopah by J. L. Butler, who located the Mizpah claim in May, 1900, and the fortunes soon realized there, attracted many people. As the boom declined, many went away, some scattering out into the surrounding country, and the population is now about 7,000. In the fall of 1902 a discovery of gold was made 23 miles south, in what is now known as the Sandstorm group, 4 miles NW. of Goldfield. In the winter of 1903—4 the Combination, January and Florence mines were discovered, and shipments of high-grade ore soon followed. In January, 1905, there were 10,000 people in Gold-field. In June, 1904, rich gold-ore was found 85 miles SE., at the foot of the south end of the Kawich mountains, but this discovery was kept quiet until a re-location could be made. On August 10, 1904, the Bullfrog claims, and a month later the Ladd mountain and neighboring claims, were located. The Shoshone group was located September 24. This district is

Jan 1, 1907

By W. A. Wood, H. L. Wain, R. I. Garrod

The mechanical behavior of recrystallized chromil~m of high purity has been studied, principally in torsion and to a lesser extent in tension, at temperatures between —196oand 350oC. Depending upon the conditions of test, the material may show brittle or ductile behavior or an intermediate or subduc-tile state having some of the characteristics of each. This latter state existed at temperatures between approximately ±50°C and was characterized by a) extensive creep at stresses well below the normal fracture stress, b) nonelastic loading/unloading effects during creep, c) strain softening under cyclic loading, and d) final failure of a brittle type. Suggestions are made on the dislocation processes and interactions which give rise to subductile behavior The ductile-brittle transition in bee metals has been studied mainly by tension and bend tests. These methods, however, favor crack propagation which may follow too closely on initiation for detailed study of the transition itself. For work of this nature, therefore, other modes of deformation less favorable to crack propagation may be preferable. This paper describes a study of the ductile-brittle transition in chromium which is based mainly on torsional testing although a few subsidiary experiments were made in tension. It appears to reveal at the transition an intermediate state that cannot properly be described as either brittle or ductile. Torsional tests on chromium have been made by other workers1 but not, as here, primarily for study of this intermediate state. EXPERIMENTAL The chromium, in the form of swaged rod, was prepared by techniques already described.' The particular material used was one in which the main impurities were 0.03 wt pet 0 and 0.006 wt pet N and one in which transition from ductile to brittle states in torsion conveniently fell at about room temperature. For torsion, test specimens were from 5/16-in.-diam rod to provide test portions 1-1/4 in. long by 7/32 in. diam, a twist of 1 deg thereby corresponding throughout this paper to 0.0015 surface shear. The specimens before test were annealed for 2 hr at 1200°C in vacuo, which left them with a re-crystallized grain size of about 0.01 mm, and then electropolished. They were tested under dead-weight loading in an apparatus in which they could be surrounded by a furnace or cooling chamber, tests in practice being made at various temperatures between -196" and +350°C. For tension tests, cylindrical specimens were prepared in a similar manner and tested at room temperature under dead-weight loading. RESULTS (TORSION) Subductile State. The state described above as intermediate between brittle and ductile may be perhaps best defined by reference to torque/twist curves at various temperatures. These are grouped in Fig. 1. Below about -50°C the material was brittle, in the sense that it exhibited little plastic deformation under stress and fractured by cleavage along planes of maximum resolved tension, which in torsion produces the well-known helical type of fracture. The deformation is typified by the curves for -196" and -150°C in Fig. 1; it shows a slight but progressive deviation from linearity above a certain torque, here about 50 lb-in., until fracture occurs at about 95 lb-in. A feature to which it is desired specially to call attention is that under none of the loads did the specimens show significant creep.

Jan 1, 1964

By F. J. Dunkerlery, V. Damiano, J. Fulton, F. Pledger

Grain-growth and recrystallization characteristics of a commercially pure zirconium prepared by the iodide process are reported. Grain growth from 640° to 800°C was continuous once initiated and obeyed D = kt". Recrystallization of zirconium occurred at temperatures of 450° to 550°C after deformations of 20 and 50 pct. Hardening from partially soluble inclusions prevented determination of the absolute rates of recrystallization, but the relative rates of recrystallization obtained are useful as a guide in fabrication practice. BASIC information needed as a guide in the hot and cold working and annealing of metals includes recrystallization and grain-growth data. A search of the literature revealed no such information for pure zirconium. This is a report of practical grain-growth and recrystallization results obtained for a commercial grade of pure zirconium on a project sponsored by the Office of Naval Research. In this work, isothermal grain-growth curves were obtained at five temperatures from 640" to 800°C inclusively; while recrystallization curves have been determined at 450°, 500°, and 550°C for the metal at the deformation levels of 20 and 50 pct. In addition to the usual variables of temperature, time, and deformation, distribution of the second phase found in all commercial grades of iodide zirconium is also treated as an important factor in these grain-growth and recrystallization studies. In conducting this work, two properties of zirconium were particularly pertinent in dictating experimental conditions. First, since zirconium undergoes a transformation from the a close-packed hexagonal form to the ß body-centered cubic form at 862°C, no recrystallization or grain-growth studies were made above 800°C. Second, because dissolved gases (oxygen, nitrogen and/or hydrogen) increase the hardness and lower the ductility of the solid metal, all annealing treatments in this investigation were carried out in vacuum or in a helium atmosphere. Materials and Methods The zirconium used in this investigation was prepared by the Foote Mineral Co. by deposition from its iodide. A spectrochemical analysis of the metal showed the following composition in weight pct: Hf, 2.1; Mg, 0.012; Fe, 0.035; Si, 0.095; Ti, 0.023; Al, 0.037; Mo, trace; Ni, trace; Cr, trace; Ca, 0.006. Conventional metallographic procedures involving hand polishing on wet metallographic papers, followed by final polishing on fine, levigated alumina on gamal cloth and a medium speed wheel were used throughout this investigation. Grain boundaries were revealed with modified Tucker's etch containing 20 parts glycerine, 2 parts hydrofluoric acid, and one part nitric acid. Grain-Growth Procedure: Three lots of zirconium, designated here as series A, B, and C were prepared for the grain-growth studies as follows: Series A was prepared by cold swaging the % in. as-deposited rod to a 3/16 in. final diameter, followed

Jan 1, 1952

By C. M. Young

This is an attempt to bring together some of the knowledge of the coal-forming conditions obtaining during the Pennsylvanian period in the Western Interior Coal Province, to sketch briefly the present extent and character of the coals produced, and to show the beginning of correlation of beds over wide areas. Coals of later age than the Pennsylvanian are not included and, for reasons that will appear later, little attempt is made to cover the districts of eastern Oklahoma and western Arkansas, and northern Texas is omitted entirely. Geological Conditions The conditions that made possible the formation of large coal beds in the United States were most favorable in the Pennsylvanian period, formerly known as the Upper Carboniferous. The geological conditions can be determined from the records, but not the reasons for them. Preceding the Pennsylvanian was the Mississippian, formerly known as the lower Carboniferous and still later as the sub-Carboniferous. During this time, large bodies of limestone were deposited and at the close of the Mississippian they were warped upward and for a long period were eroded. Then there began a period of subsidence, more or less interrupted at times, during which the Pennsylvanian strata were deposited (see table on next page). These consist of sandstones, limestones and shales, with occasional coal beds. At the beginning of the Pennsylvanian there was subsidence, which allowed the sea to extend over the eroded Mississippian surface to the north and east. It passed over eastern and central Texas, a large part of Oklahoma, with a projection into Arkansas, over Kansas and part of Nebraska, all the northern and western part of Missouri, a large part of Iowa except a strip in the north, most of Illinois, practically all of Kentucky, northern Tennessee, most of Indiana, all of the eastern part of Ohio, practically all of West Virginia, western Maryland, the west end of Virginia, and a large part of Pennsylvania. The Ozarks were already up and separated the main body of this sea, which covered the northern

Jan 1, 1936

By C. M. Young

This is an attempt to bring together some of the knowledge of the coal-forming conditions obtaining during the Pennsylvanian period in the Western Interior Coal Province, to sketch briefly the present extent and character of the coals produced, and to show the beginning of correlation of beds over wide areas. Coals of later age than the Pennsylvanian are not included and, for reasons that will appear later, little attempt is made to cover the districts of eastern Oklahoma and western Arkansas, and northern Texas is omitted entirely. Geological Conditions The conditions that made possible the formation of large coal beds in the United States were most favorable in the Pennsylvanian period, formerly known as the Upper Carboniferous. The geological conditions can be determined from the records, but not the reasons for them. Preceding the Pennsylvanian was the Mississippian, formerly known as the lower Carboniferous and still later as the sub-Carboniferous. During this time, large bodies of limestone were deposited and at the close of the Mississippian they were warped upward and for a long period were eroded. Then there began a period of subsidence, more or less interrupted at times, during which the Pennsylvanian strata were deposited (see table on next page). These consist of sandstones, limestones and shales, with occasional coal beds. At the beginning of the Pennsylvanian there was subsidence, which allowed the sea to extend over the eroded Mississippian surface to the north and east. It passed over eastern and central Texas, a large part of Oklahoma, with a projection into Arkansas, over Kansas and part of Nebraska, all the northern and western part of Missouri, a large part of Iowa except a strip in the north, most of Illinois, practically all of Kentucky, northern Tennessee, most of Indiana, all of the eastern part of Ohio, practically all of West Virginia, western Maryland, the west end of Virginia, and a large part of Pennsylvania. The Ozarks were already up and separated the main body of this sea, which covered the northern

Jan 1, 1936

By I. Nilsson, G. Sundkvist, A. Danielsson

A spectrochemical method of slag analysis is descibed which utilizes fusion of the sample with a flux, then cooling and crushing to put all samples into a common form. The powder, is then fed onto adhesive tape and passed through a spark by means of a special device to provide very reproducible discharge conditions. Combined with a direct-reading optical emission instrument, this system provides speed and accuracy of antilysis heretofore unobtainable for. slag samples by any other method. THERE are many suggested methods for spectro-chemical analysis of slags. The most important are fusion-pellet methods and solution methods. In our company the fusion-pellet method has been used earlier, and is described by Lounamaa. W. H. Tingle and C. K. Matocha have made refinements of the pellet method.' A Committee of the British Iron and Steel Research Association has investigated different methods of spectrochemical analysis of slags. Its purpose was to formulate a method which would give the complete analysis in 30 min with an accuracy of ±3 pct. The committee recommends a solution technique, which was thought to correspond best to their requirements. The method to be described is a fusion-tape method. The sample is isoformed by fusion and grinding. The powder is analyzed with the tape technique. The tape machine and some of its applications are described earlier.4'5 The powder to be analyzed is continuously fed onto a moving adhesive tape, which passes through the spark gap. The sparks break through the tape and vaporize and excite the material to be analyzed. The most outstanding feature of the tape machine is its very high reproducibility. The concept of isoformation has been introduced earlier.= It means a pretreatment of the samples to make them uniform from the spectralanalytical point of view, i.e., cancelling systematic differences between the samples. The purpose of the isoformation is to reduce the influence of particle size, as well as chemical and mineral composition. Before describing the isoformation by fusion plus grinding, which is the purpose of this paper, a few words will be said about two other types of isoformations, i.e., grinding with buffer and ion exchange plus grinding as they have been considered during the application of the tape technique for slag analysis. Grinding with buffer might be a sufficient isoformation in some special cases, where the mineral composition is defined. The time of grinding must, however, be rather long, at least 5 to 10 min, even when using such an efficient mill as the Swing Mill from Messrs. Siebtechnik, Mühlheim, Germany. This type of isoformation is not recommended due to its limitations and due to the fact that the gain in time compared with the fusion technique is almost negligible. The principle of ion exchange plus grinding and some of its applications have been described.5 The following elements of interest in slag analysis can be determined in this way: Na, K, Cu, Mg, Ca, Ba, Zn, Pb, Al, Cr, Mn, Fe, Co, Ni. The very important element Si, however, cannot be analyzed with this method. Although the ion exchange isoformation for slag analysis cannot be looked upon as a routine method, it can be used for

Jan 1, 1962

By T. S. Lundy, R. E. Pawel, F. R. Winslow, C. J. McHargue

The volume-diffusion coefficients of Nb-95 and Ta-182 in niobium have been measured over the temperature range 878° to 2400°C. High-temperature specimens (T 21500°C) were sectioned by conventional lathe and grinding techniques while low-temperature specimens were sectioned by an anodizing and stripping technique previously described. Over a range of more than ten orders of magnitude in diffusivity, the self-diffusion data is well-represented by the equation: D = (1.1+ 0.2) exp [- (96,000 * 900)/RT ] cm2/sec Upward deviations from this line are explained by short-circuit diffusion in combination with the loss of resolution of the sectioning techniques. Oxygen contamination within the range 100 to 450 ppm was found to have little or no effect on the self-diffusivitj 01 niobium. In a limited number of measurements, the diffusivity of Ta-182 in niobium was found to be about half that of Nb-95 in niobium. These data may be described by D = (I.0+0.90.5)exp [- (99,300 * 2400) /RT ] PREVIOUSLY reported studies of self-diffusion in niobium were by Resnick and Castleman1 and Peart, Graham, and Tomlin.2 The data of Resnick and Castleman over a temperature range 1585" to 2120°C show considerable scatter but. can be represented by D = (12.4 *0.8) exp [-(105,000+3OOO)/RT] cm2/sec The limited data of Peart, Graham, and Tomlin follow the equation D = 1.3 exp (-95,00O/RT) cm2/sec In view of recent diffusion data for ß zirconium3 and 0 titanium4 in which Arrhenius-type plots do not yield straight lines and of the potential high- temperature uses of niobium and its alloys, we thought it important to investigate the diffusion behavior of this bcc refractory metal over a large temperature range. This has recently been done for molybdenum,5 chromium,6 vanadium,"" and tantalum.9 Niobium was a particularly suitable material for this study largely because of the development of an anodizing and stripping sectioning technique which enables diffusivities as small as l0-19' sq cm per sec to be determined accurately.10 In addition to self-diffusion data, data were obtained for the diffusion of Ta-182 in niobium and for the effect of varying oxygen content on self-diffusion. I) EXPERIMENTAL PROCEDURE Materials. The niobium was obtained from three sources: 1) melting stock from Shieldalloy Corp., 2) electron-beam melted single crystals, 1/2 in. diameter, from Semi-Elements, Inc., and 3) oxygen-doped, electron-beam melted single crystals from Materials Research Corp. The melting stock was electron-beam melted and specimens 5/8 in. diameter by 1/2 in. long were machined from the center of the bar. The analysis supplied by the vendor and an interstitial analysis of one of the specimens are given in Table I. The single crystals (type 2 above) were cut with a jeweler's saw to specimens about 3/8 in. long. The interstitial analysis of this material is given in Table 11. This material was used

Jan 1, 1965

By R. W. Smith, T. J. Smolik

Recent work indicates that fluosilicate ions and or fluosilicate amine complex ions play important roles in fluoride activation of bery and feldspars in cationic flotation systems. In an attempt to further confirm conclusions reached in this earlier work, an infrared and X-ray diffraction study of the action of fluorides in cationic flotation of silicates was undertaken. It should be noted that in recent years considerable use has been made of infrared spectroscopy in studies of surface phenomena,2-4 and these studies have established the excellence of the technique. In the present study infrared spectra were obtained for various products of the reaction of HF and dode-cyclamine hydrochloride with quartz, microcline and beryl. These spectra were compared with one another and spectra of several inorganic and organic substances. In addition to infrared spectra, X-ray diffraction patterns were run on many of the reaction products obtained. A model 137 B Perkin Elmer Infracord double beam spectrophotometer containing sodium chloride optics was used to obtain the spectra. Infrared samples, except for the dodecylamine sample, were prepared by thoroughly mixing the substance to be analyzed with purified KBr in steel vessels on a Wig-L-Bug amalgamator. One-half in. pellets weighing 100 mg were than pressed under vacuum. Details concerning percentage of the substance to be analyzed in the pellets are indicated on the spectra. In all cases except for dodecylamine a KBr pellet was placed in the reference beam of the spectrophotometer to cancel bands due to possible impurities in the KBr. The dodecylamine sample on which an infrared spectrum was obtained was prepared by placing pure dodecylamine between two salt plates. X-ray diffraction patterns were obtained with a Norelco instrument, using a copper target tube, nickel filter and Geiger tube detector. The samples were ground into powders and either placed on glass slides with glue or placed into regular powder sample holders for diffraction studies. Goniometer scanning speed varied from 1°/min to 1/8°/min. EXPERIMENTAL RESULTS AND DISCUSSION Infrared spectra of microcline, beryl and quartz were obtained first and are shown in Fig. 1. These spectra agree reasonably well with previously reported spectra.5,6 The microcline (Fig. 1 a) and beryl (Fig. 1 b) were from good Black Hills crystals. The quartz (Fig. 1 c) was from a large, clear Brazilian crystal. It is not clear whether absorption bands of minerals are due to molecular vibrations, lattice vibrations or both. Fig. 2 shows infrared spectra of dodecylamine (Fig. 2 a) and dodecylamine hydrochloride (Fig. 2 b). The dodecylamine spectrum checks quite closely with that reported in Sadtler.8 Little is known of the spectra of hydrochloride salts of amines,9 and a spectrum of dodecylamine hydrochloride could not be

Jan 1, 1965

By P. H. Delano, Will H. Coghill, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By M. Cohen, B. L. Averbach

Many hardened steels contain significant quantities of retained austenite even in cases where the carbon and alloy contents are low. In fact austenite has been detected in plain carbon steels containing as little as 0.50 pct carbon.1 Although the austenite may not be visible metallographically it causes definite dilatometric and magnetic effects during subsequent tempering or sub-atmospheric coo1ing.l,2,3 Therefore if the reactions which hardened steels undergo during later treatment are to be understood in quantitative fashion it is most essential to have some kind of absolute analysis for the austenite content in hardened steels. Once this analysis has been made, the austenite transformations can be followed precisely by observing such sensitive phenomena as changes in length or in magnetization but the latter techniques can only determine differences in the amount of retained austenite and usually an independent method must be found to put these differences on an absolute basis. In certain instances the microscope can be used advantageously to determine the percentage of retained austenite. The quenched sample is tempered to "darken" the martensite with minimum decomposition of the coexisting austenite, and then is polished and etched in the usual fashion. If the austenite is clearly distinguishable from the tempered martensite and other possible constituents its volume percentage can be measured quantitatively by point counting or lineal analysis.4 Such microscopic methods, however, depend on the etch being sufficiently discriminatory. In fairly coarse structures, if the austenite content is greater than 10-15 pct, there is probably little smearing of the etch, and point counting or lineal analysis seems to be quite accurate. On the other hand if the structure is difficult to resolve, as in commercially treated fine-grained . steels which contain less than 10-15 pct retained austenite, the latter may be completely obliterated by the dark etching martensite or it may appear disproportionately low as the interfaces between the two constituents become difficult to distinguish. Another disadvantage of the metallographic method is the need for "darkening" the martensite and hence the determination cannot be applied to as-hardened steels. The required tempering may spoil the structure for other tests or may even remove a small part of the austenite which is being sought. X ray methods hold more promise for covering the range under 15 pct retained austenite. Although austenite and martensite in the hardened steel may be chemically identical, their crystal structures and lattice parameters differ, and the intensity of an austenite diffraction line is some continuous function of the percentage of re-

Jan 1, 1949

By Will H. Coghill, P. H. Delano, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By B. L. Averbach, M. Cohen

Many hardened steels contain significant quantities of retained austenite even in cases where the carbon and alloy contents are low. In fact austenite has been detected in plain carbon steels containing as little as 0.50 pct carbon.1 Although the austenite may not be visible metallographically it causes definite dilatometric and magnetic effects during subsequent tempering or sub-atmospheric coo1ing.l,2,3 Therefore if the reactions which hardened steels undergo during later treatment are to be understood in quantitative fashion it is most essential to have some kind of absolute analysis for the austenite content in hardened steels. Once this analysis has been made, the austenite transformations can be followed precisely by observing such sensitive phenomena as changes in length or in magnetization but the latter techniques can only determine differences in the amount of retained austenite and usually an independent method must be found to put these differences on an absolute basis. In certain instances the microscope can be used advantageously to determine the percentage of retained austenite. The quenched sample is tempered to "darken" the martensite with minimum decomposition of the coexisting austenite, and then is polished and etched in the usual fashion. If the austenite is clearly distinguishable from the tempered martensite and other possible constituents its volume percentage can be measured quantitatively by point counting or lineal analysis.4 Such microscopic methods, however, depend on the etch being sufficiently discriminatory. In fairly coarse structures, if the austenite content is greater than 10-15 pct, there is probably little smearing of the etch, and point counting or lineal analysis seems to be quite accurate. On the other hand if the structure is difficult to resolve, as in commercially treated fine-grained . steels which contain less than 10-15 pct retained austenite, the latter may be completely obliterated by the dark etching martensite or it may appear disproportionately low as the interfaces between the two constituents become difficult to distinguish. Another disadvantage of the metallographic method is the need for "darkening" the martensite and hence the determination cannot be applied to as-hardened steels. The required tempering may spoil the structure for other tests or may even remove a small part of the austenite which is being sought. X ray methods hold more promise for covering the range under 15 pct retained austenite. Although austenite and martensite in the hardened steel may be chemically identical, their crystal structures and lattice parameters differ, and the intensity of an austenite diffraction line is some continuous function of the percentage of re-

Jan 1, 1949

By R. Hoffmann

THE Waelz process produces oxides of volatilizable metals from ores, metalliferous products and residues. The process was originally used for recovering zinc and lead, where tailings and residues containing those metals had accumulated at mines or smelters, but it is applicable for obtaining tin, arsenic or other volatilizable metals. It is useful when other methods of obtaining the metals from the ores or residues are too difficult or expensive or show too low a recovery. FIG. 1.-DAILY CAPACITY OF WAELZ PLANTS RUNNING OR BEING ERECTED. The Waelz process was developed in 1923 for the treatment of large calamine dumps in Upper-Silesia, which showed zinc contents of 8 to 10 per cent. and lead contents up to 3 per cent. The rapid development of the process, from the first trials up to the plants now working or in course of erection, is shown in Fig. 1. -The first industrial Waelz plant was started in 1925. Within two years the capacity of the working plants reached 700 tons material per day of 24 hr. During the year 1928 the daily capacity of the plants now at work or in course of erection will rise

Jan 1, 1928