Search Documents

By L. G. Marshall

WHILE surveying in a small Western mine, the following problem was encountered: Two traverses had to be connected by running a traverse line down the main hoisting shaft, which was the only connection between the two levels. The shaft was inclined at about 80 deg. from the horizontal and measured 8 by 10 ft. The distance between levels was about 110 ft., measured on one side of the shaft. The surveying equipment consisted of a transit, tripod, level rod, 100-ft. chain, and plumb bobs. There were no side or top the- scope attachments with which to take large, vertical angles. Therefore, we were confronted with the problem of taking readings between two points, one of which could not be seen through the instrument when set up under the other point, owing to the obstruction of the horizontal plate, and of measuring the distance between these points with a chain that was too short. The method of a line of plumb bobs down the shaft was impractical because a setup would be needed part way down the shaft, which would call a halt to all hoisting operations for some time. After considerable experimentation the following method was used.

Jan 1, 1936

By C. Ernest Birchenall

As a basis for further progress in several branches of metallurgy, particularly the study of physical properties of solid solutions and the kinetics of solid-solid reactions, a more complete understanding of the structure of solid solutions and the nature of the metallic bond is necessary. Any investigation contributing to this understanding should be of primary interest to the metallurgist. Since the metallic bond is characteristic of an assemblage of atoms, it can be studied only where this assemblage exists. One of the most promising approaches to this study of the interactions in metals is through the general problem of binary metallic solutions. Although crystal structures of many solid metallic solutions have been determined and solubility limits for many systems are given in phase diagram studies, progress beyond this is irregular. Electromotive force and vapor pressure determinations have provided thermodynamic activity data for small concentration and temperature ranges in the amalgams and a few other systems.1 In two systems, however, copper-zinc and iron-carbon, data are available for the calculation of activities over wide ranges of temperature and concentration. This activity data for the brass system is summarized in. the preceding paper.2 A detailed study of the solubility and distribution of carbon in iron is given by Smith and Darken .3 Their treatment of interaction energies is applicable only to dilute interstitial solutions. The objectives here will be to derive from activity data given in the previous paper for the brasses and structural considerations as much new and detailed information as possible about the interactions between copper and zinc in metallic solid solution and the effect of these interactions in determining the short range structure of the equilibrium phases; that is, we shall investigate the energy of interaction between pairs of atoms of the same and different kinds, the deviations of the distribution of nearest neighbors from complete randomness, and show that the conclusions found are consistent with the observed behavior of the brass system. The method of treatment is fairly general for substitutional metallic solid solutions and will be applied to other systems. The determination of vapor pressures of the components of alloy systems is being undertaken in this laboratory to supply more data for this purpose. The information obtained from solid solutions may be extended by careful analogy to liquids as long as the metallic type of bonding is preserved. Since it will be necessary to employ the language of thermodynamics, a brief summary defining the terms used extensively in solution theory is given below.

Jan 1, 1947

By R. F. Krueger

Results are presented from tests of dynamic fluid-loss rates to cores from clay-gel water-base drilling fluids containing different commercial fluid-loss control agents (CMC, polyacrylate or smt,ch), organic viscosity reducers (quebracho and complex metal lignosulfonate) and oil at several different levels of concentration. In the dynamic system the most effective individual additives to the clay-gel drilling fluid, based on cost-equalized concentrutiom, were found to be starch and the viscosity reducers. These results do not conform with the rankings determined by API fluid-loss rests, which indicate CMC, polyacrylate and starch to be the most effective and comparable. Generally, minimum dynamic fluid-losr rates were attained at cost-equalized concentrations of additive (including thinner) of about $1.00/ bbl, or less. For chernically treated clay-gel drilling fluids, both the standard and the high-pressure API filter-loss tests were found to he inaccurate indicators of trends in dynamic fluid-loss rates under the test conditions used, particulurly for drilling muds containing viscosity reducers. From a practical field viewpoint, restrictions on the applicability of the API fluid-loss test are such that it is open to question whether or not results of this test can be used routinely with confidence as an indicator of control of down-hole fluid loss under field treating conditions. INTRODUCTION The petroleum industry spends large sums of money during drilling operations to control the fluid-loss properties of drilling fluids based on the standard API filter-loss test,' which is a static filtration system. Laboratory studies' ' of dynamic filtration have shown that in a given time period filtrate loss from a circulating mud stream is greater than from a static system and that it is a function of linear mud velocity, pressure and the properties of the drilling fluid. Ferguson and Klotz' and Horner, et al," observed that (I) the dynamic fluid-loss rates for the drilling fluids used were not related to the extrapolated API filter loss and (2) the drilling fluids with the lowest API filter losses did not have the lowest dynamic fluid-loss rates. However, there has been no published information on the relative effects on dynamic fluid-loss rate as a given drilling fluid is treated with increasing amounts of chemical additive to reduce the API filter loss. Such information is economically important because drilling-fluid costs rise rapidly as chemical requirements increase. This paper presents the results of a study of dynamic filtratioi rates to cores from a clay-gel water-base drilling fluid treated with various commercial viscosity reducers and chemical fluid-loss control agents. The dynamic fluid-. loss rates to cores are compared with the standard API filter-loss values at several different levels of additive concentration. Dynamic filtration rates were obtained in each experiment under two different simulated wellbore conditions: (1) filtration just above the bit through a new mud cake laid down dynamically on a freshly drilled formation and (2) filtration up-hole through a mud cake formed by deposition of a static filter cake on top of the initial dynamically formed cake. The latter case corresponds to the bottom-hole conditions existing above the bit when mud circulation is restarted after a stand of pipe has been added or a round trip has been made to change the bit. Except for the short-duration, high-rate filtration beneath the bit where no mud cake can form, these two conditions probably represent the two extremes of dynamic filtration. Because thickness of a dynamic mud cake formed on freshly exposed formation is limited by the shearing action of the mud stream, the filtration rate for this condition is high. On the other hand, once circulation is stopped and a static mud cake forms on top of the dynamic cake, re-starting circulation has only a small effect on the cake properties and filtration rate is much lower thereafter. A discussion of the mechanics of mud-cake deposition and dynamic filtration is outside the scope of this paper but may be found in more detail in publications by prior investigators. APPARATUS AND EXPERIMENTAL CONDITIONS The test equipment used to simulate the dynamic flow conditions existing during drilling was a modification of that described previously by Krueger and Vogel: A schematic flow diagram is shown in Fig. 1. In general, a power-driven, high-pressure mud pump capable of delivering up to 60 gallmin was used to circulate drilling fluid parallel to the faces of 1-in. diameter sandstone cores mounted in a 2 3/4-in. ID high-pressure test cell. Pump rates were controlled by means of a magnetic clutch to maintain an average axial fluid velocity of 110 ft/min in the annular space between the cell wall and a 1 1/2-in. rod positioned on the center line of the cell. The core specimens were Berea sandstone plugs sealed with plastic inside 1 1/8-in. OD tubes and were fluid-saturated prior to use. Burettes were used to accumulate fluid discharged from the cores. The mud sump shown was used for treatment and storage of the drilling-fluid samples during a particular test. The valve arrangement permitted either (1) circulating drilling fluid through the by-pass line while treating with

By Charles E. Stuart

A paper on this subject can cover but a limited range. A thorough visualization of the subject would contemplate a comparative analysis of haulage machines and batteries of various types; the relationship of the storage-battery locomotive to other types of mine haulage should be considered and limiting factors in each case should be carefully developed. This paper will deal briefly with these factors. So far as the writer has been able to determine, the first storage-battery locomotives for mine haulage were manufactured in 1897 or 1898 and were tried out in the Pocahontas coal field, but they were not sufficiently satisfactory to justify their continued use. Battery explosions were frequent and caused serious damage to the wiring, electrical equipment, and the clothing and bodies of the motormen. Sulfuric acid was used as the electrolyte. Experiments were then conducted with locomotives bearing reels of flexible cable through which connection between the motors of the locomotive and the trolley wire was maintained. At first, these reels were turned by hand. Later, the reels were revolved by contact with the wheels of the locomotive, being raised out of contact with the wheels, by a lever, when necessary. About 1902, the plan of operating the reel, by chain and sprocket wheels, from one of the locomotive axles, as is still the practice, was devised. The popular floating motor-driven reel had its inception in the Pocahontas fields prior to 1906. The maximum radius of operation of the reel-type locomotive is about 500 ft. (150 m.) from point of connection with trolley wire. This is ample for room work and certain entry work, but the need for a machine that would operate entirely independently of the trolley wire was so great that, with the development of the storage battery, renewed efforts were made to manufacture a successful storage-battery locomotive. About 1908, the gasoline locomotive was introduced. In spite of many objections to this type of machine for such work, the fact that hundreds of these machines were purchased was proof of the need for a machine operating independently of the trolley.

Jan 1, 1923

By Charles E. Stuart

A paper on this subject can cover but a limited range. A thorough visualization of the subject would contemplate a comparative analysis of haulage machines and batteries of various types; the relationship of the storage-battery locomotive to other types of mine haulage should be considered and limiting factors in each case should be carefully developed. This paper will deal briefly with these factors. So far as the writer has been able to determine, the first storage-battery locomotives for mine haulage were manufactured in 1897 or 1898 and were tried out in the Pocahontas coal field, but they were not sufficiently satisfactory to justify their continued use. Battery explosions were frequent and caused serious damage to the wiring, electrical equipment, and the clothing and bodies of the motormen. Sulfuric acid was used as the electrolyte. Experiments were then conducted with locomotives bearing reels of flexible cable through which connection between the motors of the locomotive and the trolley wire was maintained. At first, these reels were turned by hand. Later, the reels were revolved by contact with the wheels of the locomotive, being raised out of contact with the wheels, by a lever, when necessary. About 1902, the plan of operating the reel, by chain and sprocket wheels, from one of the locomotive axles, as is still the practice, was devised. The popular floating motor-driven reel had its inception in the Pocahontas fields prior to 1906. The maximum radius of operation of the reel-type locomotive is about 500 ft. (150 m.) from point of connection with trolley wire. This is ample for room work and certain entry work, but the need for a machine that would operate entirely independently of the trolley wire was so great that, with the development of the storage battery, renewed efforts were made to manufacture a successful storage-battery locomotive. About 1908, the gasoline locomotive was introduced. In spite of many objections to this type of machine for such work, the fact that hundreds of these machines were purchased was proof of the need for a machine operating independently of the trolley.

Jan 1, 1923

By G. S. Rice

With so tremendous a subject, an attempted review of the coal situation of the world in a short talk must necessarily be of a sketchy character. It is hardly necessary to tell a body of engineers that had it not been for nature's gift of coal the material side of modern civilization would never have reached its present status. On the other side, it is regrettable that it was a byproduct of coal, T. N. T., which made possible Germany's initial success in this war, because that country had an enormous development of manufacturing plants that could be immediately utilized to make this destructive agent: One sometimes hears the casual remark that when the coal of the world is exhausted we shall use electricity; but, of course, electricity is ordinarily only a means of transforming and transmitting energy derived from fuel or water power, and chiefly from coal. It is true, we have much undeveloped water power, but it is more or less remote from 'the, centers of industry; and when all shall have been developed it will not begin to supply the power requirements of the world. It is, however, reasonable to expect that before the world's supply of coal shall be exhausted, methods will have been discovered of harnessing other forces of nature, such as the tides, or the energy emanating from the sun. Petroleum and natural gas naturally come to mind, but the days of both, as fuel, appear to be numbered, although the products of petroleum, if economically used, doubtless will be available for internal-combustion engines, automobiles, trucks, and boats for a long time, provided the reckless use of crude petroleum as an ordinary fuel is stopped. The products of petroleum are too valuable to mankind for such waste to be permitted. The civilization of the world, therefore, appears to rest, and, so far as can be seen, will indefinitely continue to rest, upon coal. COal Resources of the World According to the compilation made by the geologists of the principal countries for the 12th International Geologic Congress, held in Canada

Jan 1, 1918

By Shiro Ban-ya, John Chipman

Using the same experimental method previously described, the activity of sulfur in a number of quaternary and more complex liquid iron alloys at 1550oC is determined. A "cross-product term zj.zk is determined for each of the quaternary alloys to take account of the mutual effects of the combinalion on the indi-vidual contributions to In 5 The interactiotl coefjicienls delermined for ternary solutions and cross-pvoducl coefficierlts from the quaternary systems are used to estimate the activity coefficient of sulfur in more complex alloys. OUR recent papers 1,2 have described new determinations of the activity of sulfur in Fe-S binary and Fe-S-j ternary solutions, but the practical applications of these data require the estimation of activity of sulfur in more complex systems. Previously, Sherman and chipman3 devised an approximate method for calculating the activity of sulfur in complex systems by summing the contributions to the logarithm of the activity coefficient of each element in the alloy. This procedure is more successful, as one of us has pointed out,4 when the concentration variable is taken as zs = ns/(nFe — nS t CLJ~ nj) rather than the conventional atom fraction x~ = nS/(nF, + nS + Enj). In the former definition, which is based on analogy to interstitial solutions, the value assigned to uj is normally +1 for metallic and -1 for nonmetallic elements." In addition, however, the effects of mutual interaction between alloying elements must be considered for the accurate estimation of the activity of sulfur in more complex systems. The purpose of this investigation has been to devise a more reliable method for estimating the activity coefficient of sulfur in nmIticomponent iron alloys. The measurements were carried out on some quaternary systems Fe-S-j-k for combinations of silicon, chromium, nickel, cobalt, molybdenum, and tungsten. Manganese was not included since the experimental method has been found unsatisfactory for volatile, sulfide-forming elements. The experimental method was the same in every detail as described previously. 1,2 The concentrations of sulfur, silicon, chromium, and copper in the quenched metals were determined by chemical analysis but those of nickel, cobalt, molybdenum, and tungsten were calculated from charged amounts. Iron sulfide was included in the charges in amounts estimated to furnish approximately the final sulfur content. CALCULATION W2 have shown2 that when zs and zj are the concentration variables in a ternary Fe-S-j solution the logarithm of the activity coefficient S = a~/zg is a linear function of the variables as and aj defined as follows:

Jan 1, 1970

By James H. Hance

Several years ago the writer was connected with the Mint and Assay Service of the Federal Government as Assistant Assayer at the Salt Lake Assay Office. At that time cyanide bars formed approximately half of the bullion purchased by that office. Disagreement in valuat,ion between the producer and the office was not infrequent and to a lesser extent between the Assay Office and the Mint, this latter issue being soon obviated, however, by adopting uniform methods of sampling the bars. A nice problem seemed to offer itself for research and the writer began a series of experiments which were soon terminated, however, by his going into other work, and which he regrets have not since been completed. The results attained may suggest lines of approach to this problem and are, therefore, offered in this article. Frederic P. Dewey, Assayer of the Mint Scrvice, U. 5. Treasury, has had abundant opportunity to study this phase of metallurgy, and has published several articles relative thereto.1 In the last article cited Dewey quotes analyses of cyanide bullion similar in content to that with which the writer worked, and which show some of the variations met with. In the discussion of these papers,2 comparison has been made in terms of copper bullion, but to the writer this seems of questionable value. Copper bullion may resemble silver bullion, but its similarity to gold bullion with little or no silver content is another thing. The freezing-point diagram of Roozeboom, reproduced on page 881 of the discussion cited, is for the gold-silver series as stated. The original problem under discussion, however, is not this alloy but gold with base metals other than copper. As for the statement that the corners are the worst places or

Jan 1, 1916

By C. W. Hamilton

In the production of crude petroleum for the year 1930 Venezuela again maintained its world rank of second only to the United States. During the latter months of the year Russia forged ahead of Venezuela in daily rate of production, and from the present outlook will probably rank second among the oil-producing countries of the world in 1931. It is now believed Venezuelan production has passed its peak. The producing fields of the Bolivar coastal district, along the east side of Lake Maracaibo, continue to be the principal source of supply. Such fields as Lagunillas, Mene Grande and La Pas were not produced to capacity throughout 1930. During the year, three new fields entered into commercial development: The Rio Tarra field in the District of Colon, State of Zulia; the El Mene de Salto field in the District of Acosta, State of Falcon and the Quiriquire field, District of Piar, State of Monagas. For 1930 the total crude production of Venezuela was approximately 137,424,000 bbl. as compared to 137,739,000 bbl. during 1929, or a decrease of 315,000 bbl. During the past year exports of crude from Venezuela amounted to 137,8.50,000 bbl. as against 130,044,000 bbl. exported during 1929. Crude oil in field storage decreased from 14,138,-000 bbl. at the beginning of 1930 to 9,600,000 bbl. as of Jan. 1, 1931— present crude stocks fill about one half the field tankage available. Drilling operations in the producing fields declined sharply but throughout the year there was maintained a satisfactory potential reserve in the shape of proven territory and closed-in producers. Of the 2555 wells which have been completed in Venezuela, 1571 wells were in production on Jan. 1, 1931. The status of these present producing wells may be classified as follows: flowing 652, pumping 170, gas-air lift 193 and closed-in 556. The ratio of closed-in wells to producing wells declined in 1930, while the number of wells produced by artificial means increased materially. In the Bolivar coastal fields there is now observed a marked decline in gas volume and well-head pressure. Lago Petroleum Corpn. and Venezuela Gulf Oil Co. each have under construction electric plants designed to generate power for pumping wells by electricity. The first units of these plants will be placed in conlmission in the early spring of 1931. Venezuela Oil Concessions, Ltd. has installed a number of stenrn-

Jan 1, 1931

By R. S. Hoch, Roy A. Bobo

Maintenance of desirable plastic flow properties of weighted drilling muds may be greatly simplified by use of centrifugal classification to control the drilled solids content. The new application of a decanting type centrifuge to separate and reject the low density solids from the weighting material results in a drilling mud of greatly improved quality with lower values of yield and rigidity. Its practicality and economy has been proven in field operation. The degree of separation of light and heavy solids is not limited by the machine, but by the particle size distribution of the solids in the mud. Removal of the low density component of drilling mud that makes chemical treatment necessary permits a marked reduction in chemicals. The main uses of the centrifugal process are the treatment of muds while drilling, the reclaiming of discorded muds, cleaning up of workover muds, and the reduction in lime content of mud for completion. INTRODUCTION Drilling mud in any circulatory system is made viscous and difficult to pump by gradual accumulation of drilled solids which pass through the shale shaker and are continually reground. In a weighted mud containing a large proportion of barite by volume, the amount of drilled solids that may be tolerated is greatly reduced. Much effort has been expended to control by chemical treatment the effects of such solids. Though chemical treatment is quite effective, the time eventually comes at deeper depths after enough drilled solids have entered the system when a portion of the mud must be discarded and replaced with water and more weighting material. Once begun, this process is generally continued at frequent intervals with resultant high maintenance costs. At the termination of drilling, mud highly contaminated with light solids and spent chemicals is poorly suited for completion operations.' It is likewise limited in utility for other drilling operations. This investigation was conducted for the primary purpose of determining an acceptable mechanical means of removing the lightweight solids from weighted drilling muds in order to maintain viscosity at a minimum. A decanting type of centrifuge was selected from the various possible methods of mechanical separation. The centrifugal process has been employed in this country for this purpose in central mud reclamation systems in California in earlier years. It also was used for treatment of weighted muds on the Gulf Coast.' In more recent years only sporadic attempts have been made to employ it in the field on weighted muds. DISCUSSION OF PROCESS Selection of Apparatus Two factors favor mechanical procedure for the separation and removal of drilled solids or clays from the mud circulatory system. First, the greater specific gravity, 4.1 to 4.3, of the barite would promote more rapid settling than the clays whose specific gravity range is from 2.5 to 2.7. Second, the relative coarseness of the barite particles also facilitate faster settling of this phase. A decanting type of centrifuge was preferred for this process over other possible methods for these reasons: 1. Requires no costly additives or excess dilution. 2. Centrifugal force affords greatly accelerated separation as compared to gravity.

Jan 1, 1955

By Joseph L. Gillson

In this volume, which is divided into chapters on a commodity basis, many subjects inevitably have a common interest with others, or are interrelated in one way or another. No group of commodities is so outstanding in this regard as is that group of which the basic raw material is a carbonate rock. There are chapters in this book on dimension stone, on crushed stone, on chalk and whiting, on cement, on lime, on magnesite, on sodium carbonate; all of which are entirely, or partly, products of the "carbonate rocks." Rhodochrosite, witherite and strontianite are other carbonates described respectively in chapters on manganese minerals, barium minerals and strontium minerals; and travertine and cave onyx are carbonate materials used as ornamental stones. High grade marble is used for monuments and statues and as a decorative building stone. The aggregate tonnage of the basic raw material, the carbonate rock, is so enormous that it exceeds the tonnage of any metallic ore mined and quarried in the United States, and in turn is exceeded only by coal, sand and gravel, and by water in the gross tonnage produced by the mineral industry in this country. The specialties, including magnesite, sodium carbonate, and rhodochrosite, witherite and strontianite are produced from uncommon rock types of limited occurrence. They are described adequately in the chapters devoted to these subjects. This chapter is concerned with the limestones and dolomites. No other solid rocks are as important as these in the industrial life of the world, nor are any so widely known. Massive units of some carbonate formations form many of the spectacular features of some of the most rugged mountains in the world, such as the Dolomite Alps, the Canadian Rockies, some rugged peaks of the eastern flanks of the American Rockies in Colorado, Wyoming and New Mexico and in many ranges in Utah, Nevada and Arizona. These continue down the Sierra Oriental in Mexico and on around the world to the flanks of the Himalayas, in the South China Highlands, and separating Asia and Europe in the flanks of the Ural Mountains where they form many reexhumed hills called Shikhany.50a Less rugged and more nearly flat-lying carbonate rocks underlie most of the area of our great Middle Western plain, the southern part of England and the northern part of Africa. These are the common rock formations known from boyhood to a large part of the world's population. The use of lime, produced by the burning of limestone, goes back to antiquity, and mortar was used widely in Biblical times. The cement made by mixing volcanic ash with lime was a basic material of construction when Pompeii was built. Our Eastern states are dotted with abandoned limestone quarries, and the ruins of old lime kilns which were operated in Colonial days. Many limestones and dolomites are found in flat-lying strata of a thickness convenient for quarrying as a building stone, so that houses and other structures have been built with them for centuries. In order to replace the muddy and rutted dirt roads with surfaces that could stand the hard usage of his wagons and carts, man learned to crush stone and put a layer of it on his old trails. Such roads built by the Romans have been in use over much of

Jan 1, 1960

By E. W. Hough, G. L. Stegemeier

Empirical equations for surface tension of propane and normal butane as functions of reduced temperature are obtained from experimental data. Another correlation relating surface tension to enthalpy of vaporization is given for these two compounds. In addition, new paracbor numbers are calculated for the normal paraffin hydrocarbons. These numbers are utilized for the calculation of interfacial tension of two-component systems as functions of pressure and temperature, using a modified form of Weinaug-Katz equation. The experimental data for two binary systems are approximated by the correlation. From these results it is found that the interfacial tension in the high-pressure region remains extremely low at large pressure decrements below the critical pressure. Thus, it appears that condensate systems may have flow characteristics almost like single-phase conditions even though the pressure is within the two-phase region. Experimental data have shown that interfacial tension divided by density difference approaches zero as the critical pressure is approached. A calculation of wetting-phase saturations indicates that the saturation gradient at the two-phase contact becomes increasingly abrupt as the critical pressure is approached. DISCUSSION Prediction of the surface and interfacial tension of the light hydrocarbons and of two-component hydrocarbon mixtures at various temperatures and pressures may be made if other physical properties are known. Extensive experimental work on single-component and binary systemsl is the basis for the correlations outlined in this paper. Interfacial tension is defined as the specific surface-free energy between two phases of unlike fractional composition, while surface tension is defined as the specific surface-free energy between two phase:; of the same fractional composition. The usual definitions relating interfacial tension to a liquid-liquid interface and surface tension to a gas-liquid interface are not clearly defined when the critical region is included, and there is no sharp distinction between a gas and a liquid phase. Interfacial tension is probably the most important single force that makes one-half to one-third of the total oil actually in place in a reservoir rock unrecoverable by conventional gas-drive or waterflood methods. A rough estimate of this figure for the United States is 100 billion bbl. Interfacial tension presently is used by petroleum engineers in the estimation of saturation gradients at the gas-oil contact and at the oil-water contact. The data in this paper should prove useful for estimates of reserves involving gas-oil contacts. Relative permeability undoubtedly is influenced by interfacial tension, for sufficiently small values. These data should be useful in determining how small the values are In addition, these data should eventually add to our fundamental knowledge of surfaces. At the critical point, all surface excesses approach zero and the thickness becomes very large. SINGLE-COMPONENT SYSTEMS It has been observed1 that the following relationships are good approximations to the physical properties of propane and n-butane.

By E. Brunner, G. L. Hassler, T. J. Deahl

The capillary effects in reservoir rock are discussed in terms of the pressures they cause in sandstones and dolomites. Data for the two-phase case (oil-gas or water-gas) and for the three-phase case (oil, water and gas in rock) are used to demonstrate that in one sense the wetting preference of a rock depends on its saturation. The nature of capillary hysteresis is described for partially stable conditions, and the concept is enlarged. Reproducibly measurable pressures include the "capillary pressure," which is the pressure difference between any two phases that are each interconnected; the "threshold pressure," necessary to force a nonwetting phase through partially saturated rock; the "displacement pressure," which is that special case of the threshold pressure in which both phases fully saturate separate portions of the rock. Displacement pressure is equal to the minimum value of the "capillary pressure." The theory of flow including capillary forces is developed at the producing surface of a well to reveal the presence there of a pressure discontinuity in the gas (or other nonwetting) phase that can be controlled to the end that more oil may be poduced from an oil field. Experiments with packed sand-flow tubes having artificial producing surfaces support the theory. Introduction The basic surface quantities acting in an oil field are two: namely, surface tensions and contact angles. These are the quantities, variously expressed, and particularized as spreading forces, adhesion tensions, heats of wetting, etc., which are measured in the laboratory by techniques mostly confined to flat or circularly cylindrical surfaces. Such measurements have not had the extensive engineering application they seem to deserve because in most practical cases they are unavoidably compounded with the complex and unapproached subject of the internal shape of the interstices of rock. In this paper it is intended that the pressure differences developed in rock by capillarity be examined, defined, and given some engineering use in terms of some new measurements that have been made. Such pressure differences—namely, the capillary pressure, the displacement pressure and the threshold pressure—seem to provide a proper contact between the basic molecular quantities and the oil field. While certain modifications of usage will be undertaken, the present effort rests upon the background of work by the U. S. Geological Survey,l by Versluys, and especially by W. 0. Smith, 3,4,5 which has been reviewed recently in papers by Leverett.=s7 The most important concept of pressure difference is the capillary pressure, a function of saturation that expresses the pressure difference between the interconnected phases in a rock. It is often measured when water and air are the fluids present, but it can be measured with other fluids. A number of curves of capillary pressure have recently been measured by a method which it is intended shall be published in a later paper. Since heretofore capillary-pressure measurements upon rock have not been

Jan 1, 1944

By G. L. Hassler, E. Brunner, T. J. Deahl

The capillary effects in reservoir rock are discussed in terms of the pressures they cause in sandstones and dolomites. Data for the two-phase case (oil-gas or water-gas) and for the three-phase case (oil, water and gas in rock) are used to demonstrate that in one sense the wetting preference of a rock depends on its saturation. The nature of capillary hysteresis is described for partially stable conditions, and the concept is enlarged. Reproducibly measurable pressures include the "capillary pressure," which is the pressure difference between any two phases that are each interconnected; the "threshold pressure," necessary to force a nonwetting phase through partially saturated rock; the "displacement pressure," which is that special case of the threshold pressure in which both phases fully saturate separate portions of the rock. Displacement pressure is equal to the minimum value of the "capillary pressure." The theory of flow including capillary forces is developed at the producing surface of a well to reveal the presence there of a pressure discontinuity in the gas (or other nonwetting) phase that can be controlled to the end that more oil may be poduced from an oil field. Experiments with packed sand-flow tubes having artificial producing surfaces support the theory. Introduction The basic surface quantities acting in an oil field are two: namely, surface tensions and contact angles. These are the quantities, variously expressed, and particularized as spreading forces, adhesion tensions, heats of wetting, etc., which are measured in the laboratory by techniques mostly confined to flat or circularly cylindrical surfaces. Such measurements have not had the extensive engineering application they seem to deserve because in most practical cases they are unavoidably compounded with the complex and unapproached subject of the internal shape of the interstices of rock. In this paper it is intended that the pressure differences developed in rock by capillarity be examined, defined, and given some engineering use in terms of some new measurements that have been made. Such pressure differences—namely, the capillary pressure, the displacement pressure and the threshold pressure—seem to provide a proper contact between the basic molecular quantities and the oil field. While certain modifications of usage will be undertaken, the present effort rests upon the background of work by the U. S. Geological Survey,l by Versluys, and especially by W. 0. Smith, 3,4,5 which has been reviewed recently in papers by Leverett.=s7 The most important concept of pressure difference is the capillary pressure, a function of saturation that expresses the pressure difference between the interconnected phases in a rock. It is often measured when water and air are the fluids present, but it can be measured with other fluids. A number of curves of capillary pressure have recently been measured by a method which it is intended shall be published in a later paper. Since heretofore capillary-pressure measurements upon rock have not been

Jan 1, 1944

By Ralph L. Erickson

The discovery of a Carlin-type gold deposit at Cortez, Nevada, in 1966 can be attributed directly to the use of geochemical exploration techniques. Most mineral deposits owe their discovery to geologic concepts, geologic analysis, and luck, but at Cortez, geochemistry as an exploration tool played the clearly dominant role in discovery. Of course, the economic significance of the discovery had to be determined by exploration and development drilling. The story of the discovery began in 1959 when field work was initiated on a new project, "Geochemical Halos Utah and Nevada," by R.L. Erickson and A. P. Marranzino for the US Geological Survey. The Cortez district was selected for geochemical work because it was an area with good geologic control where we could address the problem of how to prospect in barren outcrops for concealed ore deposits in potentially favorable structures (buried thrust zones) or favorable host rocks in the subsurface. Geologic mapping of the Cortez 15-min quadrangle, just being completed by Gilluly and Masursky (1965), showed that the quadrangle contained excellent exposures of both the upper and lower plates of the Roberts Mountains thrust fault, a major structural feature of north-central Nevada. Roberts (1960) had noted that a number of mining districts were associated with windows in the thrust. In 1959, Erickson and Marranzino did some reconnaissance rock sampling and spring-water sampling in the siliceous clastic rocks of the upper plate of the thrust. Results of this reconnaissance prompted a full-scale sampling program in 1960 in the upper plate rocks on the west flank of the Cortez window. Results of the investigation showed that anomalously high concentrations of metals occur in the upper plate rocks, and further, that the distribution of metals is fault controlled and shows a pronounced zoning pattern (central copper zone; intermediate zinc, copper, and lead zone; and outer arsenic zone). The anomalies were interpreted as primary leakage halos that originated from metal occurrences in the thrust zone or in carbonate rocks below the thrust and moved upward along normal faults that cut both upper and lower plate rocks. Erickson gave a talk about these anomalies in the summer of 1961 to the local AIME Section in Reno, Nevada; two short reports were published that year-" Geochemical Anomalies in the Upper Plate of the Roberts Thrust Near Cortez, Nevada" (Erickson et al., 1961) and "Hydrogeochemical Anomalies in Four Mile Canyon Near Cortez, Nevada" (Erickson and Marranzino, 1961). These releases prompted blanket staking in the area by several small companies. In 1963, geologic and geochemical mapping were started by the USGS in the lower plate carbonate rocks of the Cortez window west of the quartz monzonite stock at Mount Tenabo and north of the old townsite of Cortez. The results of the work showed anomalously high concentrations of arsenic, antimony, and tungsten in jasperoid, fracture filling, and shear zones in Silurian and Devonian carbonate rocks. The anomalous area was about 1.6 km (I mile) long and 300 m (1000 ft) wide. A brief report, "Geochemical Anomalies in the Lower Plate of the Roberts Thrust Near Cortez, Nevada" (Erickson et al., 1964a), was published in 1964. During this same time period, 1959-1964, several exploration or mining companies were active in the general area (chiefly mapping geology and acquiring property). In 1964, American Exploration and Mining Company (Amex) concluded that the entire Cortez district was worthy of an extensive exploration effort involving drilling as well as geologic, geophysical, and geochemical studies. To carry out the program, Amex formed a joint venture group with the Bunker Hill Company, Vernon Taylor, Jr., and Webb Resources. Their early efforts were directed to the upper plate rocks and to the lower levels of the old Cortez silver mine. The group also drilled some shallow rotary assessment holes adjacent to the area of the arsenic, antimony, tungsten anomaly in lower plate carbonate rocks described in Erickson et al. (1964a). Assay results from these holes offered little or no encouragement to the joint venture group. Splits of these drill samples were made available to the USGS. In order to enhance any metal content present in these rocks and to determine the mineral residence of any metals detected, heavy-mineral concentrates of each 3-m (10-ft) sam-

Jan 1, 1985

By C. P. McCormack

The Cuyuna manganiferous iron ores can be a principal source of manganese for the iron and steel industry in the United States, provided metallurgical methods as a whole are adjusted so as to use run-of-mine ore. The use of manganese in steelmaking is growing. Increasing amounts of impurities in raw materials call for more manganese, a constant cheap supply of which is wanted. There are few deposits of ore in the United States carrying over 35 per cent. manganese that can be mined and marketed at a profit in normal times. We are largely dependent on foreign ores. The small domestic deposits should rightly be held in reserve for an emergency, such as a war, when importation might cease. Even the production from lean ores, concentrated it may be, might not carry us through a protracted stringency. The Cuyuna district is, therefore, during normal times capable of supplying a large total of manganese. The ores are iron ores containing 5 to 25 per cent. of manganese with the inverse range of 52 to 28 per cent, of iron. The manganese costs no more per unit in the ore than the iron, because cost of mining, largely by open-pit methods, is not affected by the manganese content. The manganese units should, perhaps, command a higher price, but as their value is contingent on metallurgical practice, a higher price may be justified only when a shortage in manganese occurs. Manganiferous iron ores can never entirely supplant straight manganese ores though methods are employed that will permit them to do so partly. For the manufacture of ferromanganese, ores carrying above 42 per cent. manganese are needed. Ores with manganese running between 20 and 42 per cent. are used for making spiegeleisen. But established practice in certain plants, based on the admixture of manganiferous iron ores to straight iron ores has greatly lessened the consumption of high-priced, scarce, manganese alloys with good results. The substitution of manganiferous ores for ferro and spiegel affects the manufacture of basic iron and its conversion into basic open-hearth

Jan 1, 1925

By M. C. Udy, F. W. Boulger

AN incomplete phase diagram for the U-Ti systern was determined earlier 1 and more recently, a tentative diagram was presented for the uranium-rich end of the system.' In the present re-examination of the whole system of U-Ti alloys, high purity materials were used. Melting stock for the alloys was high purity uranium, containing about 0.09 pct C as the only appreciable impurity, and high purity iodide-process titanium purchased from New Jersey Zinc Co. Both metals were cold rolled to about 1/6 in. thickness, sheared to about I/' in. squares, and cleaned by pickling. The alloys were arc melted under a helium atmosphere in a water-cooled copper crucible. A thoriated-tungsten electrode was used. The furnace chamber was evacuated, then flushed with helium, prior to each melting. It was finally filled with stagnant helium at one atmosphere pressure. Each alloy was remelted three times after the original melting, to insure homogeneity. The alloy button was turned bottom side up before each re-melting operation. Some 22 alloys were examined. Their compositions were spaced at appropriate intervals between 100 pct Ti and 100 pct U. Analyses were made on chips taken after fabrication. The major contaminant was carbon, which varied from 0.03 to 0.08 pct. It appeared in the microstructure as titanium carbide. Alloy compositions were calculated to a carbon-free basis for consideration on the diagram. Tungsten and copper, possible contaminants from the melting operation, were generally less than 100 parts per million each. Fabrication All alloys were forged and rolled to bars approximately V8 in. square. They were clad either in SAE 1020 steel or in a 5 pct Cr-3 pct Al-Ti-base alloy, depending on the fabrication temperature. A temperature of 1800°F (980°C) was used for alloys near the compound composition. This necessitated using the titanium-base alloy, since iron reacts with titanium at this temperature, producing a low melting alloy. Other alloys were fabricated at 1450°F (790°C), using steel jackets. No iron-titanium reaction occurred at this temperature. The jackets were welded in place in an argon atmosphere. Those alloys sheathed in steel were declad and then reclad between rolling and forging operations. On the other hand, those clad with the titanium alloy were cut to a roughly rectangular shape prior to clading and were then carried through both the forging and rolling operations without opening. Those alloys near the compound composition were found to be cracked when the clading was removed. The cracked materials had been plastically deformed, however, and at least some of the cracking had OCcurred during cooling. Heat Treatment The rolled bars, after being declad and shaped to remove surface contamination, were all given an homogenizing treatment of 160 hr at 2000°F. (Samples were taken for analysis following the declading and shaping operations.) All were heat treated at the same time in one furnace, but each was sealed in a purified argon atmosphere in an individual Vycor glass tube. Argon pressure was such that it was approximately atmospheric at temperature. One end of each tube contained titanium chips and this end was heated to 1200°F (650°C) for 10 min prior to the heat treatment. This purged the atmosphere of residual reactive gases. The balance of the tube was warmed during the purge to liberate adsorbed moisture and gases, which also reacted with the hot chips. The bars were furnace cooled from the homogenization treatment. Specimens of each alloy were water quenched after 2 hr heating at 1000°, 1200°, 1400°, 1600°, 1800°, and 2000°F (540°, 650°, 760°, 870°, 980°, and 1095°C). In addition, some were treated at intermediate temperatures of 1300°, 1500°, and 1700°F (705", 815", and 925°C) and at 2150°F (1175°C). Specimens, about '/s in. cubes, were cut from the bars, sealed in individual Vycor tubes, and heat treated as described. All specimens heat treated at the same temperature were processed together. Samples were quenched by breaking the Vycor tube rapidly under water. Metallographic Examination Specimens were mounted in bakelite and ground wet on 180 grit paper held on a 1750 rpm disk. They were then ground wet by hand, using 240, 400, and 600 grit papers. The rough grinding was continued long enough to get well below the surface. Specimens were mounted separately because of the variation in the rate of etching between alloys. The specimens were polished with rouge on a 4 in., 1725 rpm wheel covered with Miracloth. Alloys on the titanium side of the compound composition were etched with a solution of 2 pct hydrofluoric acid in water saturated with oxalic acid. A few crystals of ferric nitrate were added as a bright -ener. Specimens were immersed 5 sec, polished to remove the etch, then re-etched. With the higher titanium alloys, it was often necessary to start the etch on the polishing wheel, because of the formation of a passive film. In some instances, a plain 2 pct hydrofluoric etch was satisfactory. For the alloys on the uranium side of the compound, a distinction between the compound and the uranium phase developed after standing a short time in air. This could be hastened by the application of heat, such as obtained by placing the specimen on a radiator. A deep etch was necessary to develop details in the uranium-rich phase, such as the Widmanstaetten pattern sometimes obtained by quenching y uranium. A 2 pct hydrofluoric acid solution was used for this deep etching.

Jan 1, 1955

J. B. Cohen (AVCO Mfg. Co.)-The model presented by the authors is only one of several possible mechanisms for low-temperature aging. It is true that the motion of dislocations to the copper atoms, followed by diffusion along the dislocation lines, is one such mechanism. However, the details of such a process which would :result in copper-rich platelets on (100) planes in the f.c.c. matrix are not clear. Furthermore, there is at least one other mechanism that may be used to e.xplain the authors' results, so that the data do not clearly favor the Turnbull model. The zones may form by "normal" diffusion. The diffusion constants would be higher at room temperature than extrapolated data would suggest due to vacancies trapped in the specimens in the quench. The diffusivity would then be multiplied by the ratio of the number of vacancies present at the solution temperature to that present at room temperature. These vacancies could remain in the alloy specimen for long times at room temerature, due to interaction with the copper atoms. ' The activation energy for diffusion is smaller than that for bulk diffusion at elevated temperatures for it is only that for the motion of vacancies existing after the quench; after these are used up, the aging process effectively ceases. It is somewhat questionable if the laws governing transformation kinetics can be directly applied to changes in elastic moduli, especially in the case of aging where the structure and the composition of the zones may be changing during aging, If such laws are assumed, it is possible to explain the exponential factor of % with this vacancy model. It is probable that the structure of the zones and the matrix match only on (100) planes. Certainly the precipitates that form in this system after various aging treatments show orientation relationships similar to those of the zones. Strains on the edges of the zone may set up fields which do not allow the zone to grow in an edgewise manner. The exponent in the growth of a thin plate in a direction perpendicular to its face would be %. It may also be that copper atoms are attracted to dislocations. If this is the rate-controllin factor in the growth process Ifthisthen an exponent of % or % may arise. The writer would like to know if the authors have tried plotting l/a; proportional to as might be expected for "dislocation drainage." R. H. Doremus (General Electric Research Laboratory)—An important new method for following the growth of Guinier-Preston zones is presented in this paper, and I wish to congratulate the authors on their experiments. Their interpretation of the results, however, is doubtful in certain respects. To determine the exponent m in Eq. [4] the authors plotted -log at against t to various powers (their Fig. 6). The initial value of frequency used for these plots was found by extrapolating the data to zero time. In Fig. A the data from their Fig. 2 are plotted against a linear, rather than logarithmic, time scale. To obtain graphs similar to their Fig. 6 for these data one must use an initial frequency of about 52720; such a plot for m = % is shown in Fig. B. The straight line in Fig. B fits the data in an intermediate range only. The curve drawn in Fig. A was mapped from this line; comparison of

Jan 1, 1960

Discussion of the paper of W. R. Shimer and F. O. Kichline, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 81, September, 1913, pp. 2361 to 2377. ALLERTON S. CUSHMAN,* Washington, D. C.:-I have been much interested in Mr. Shimer's valuable contribution. The apparent fact that the oxides of certain metals which are not reduced by hydrogen per se, are reducible when the oxides are dissolved in iron in small quantity, is brought out for the first time, and is worthy of the careful attention of investigators. The Ledebur method has been subjected to considerable criticism, owing to the alleged fact that it did not measure the oxygen combined with impurities. Personally I have found the method extremely helpful in spite of the minute quantities of oxygen with which it deals. Mr. Shinier points out that the highest oxygen he obtained by over-blowing was 0.074 per cent., while the minimum quantity in a properly finished steel was in the neighborhood of 0.02 per cent. The Ledebur method is used as a constant check on the quality of heats made in practice under my direction. In dealing with a very pure commercial iron, we should expect to find and would find difficulty in galvanizing sheets made from a heat running 0.07 per cent. oxygen. In fact, we do not like to have the oxygen rise above 0.03 per cent. I am inclined to agree with the author that excessive oxygen leaves a bath of metal in a very short time, but nevertheless I believe it takes only a very little combined oxygen to begin to make its presence felt in the pickling and galvanizing department, when sheet metal is the product manufactured. As Mr. Shimer points out, the higher the carbon, the lower the oxygen danger, and it is partly for this reason that the manufacture of carbon-free metal in the open-hearth furnace has to be so very carefully watched and controlled from the furnace through to the finished product. It is quite possible that, there is a critical temperature of dissociation between iron and oxygen, although the critical points may vary in baths of different carbon content. Unfortunately, the accurate determination of the temperature of a molten bath at the time of pouring or teeming is a very difficult matter. For a long time I have been wishing that there were some reliable data which would indicate the effect of the tem-

Jan 12, 1913

By H. L. Gilbert, C. Travis Anderson, W. J. Kroll

IN a previous paper,1 the use of a split graphite tube resistor as a heater element for high-temperature furnaces has been described. The principal advantages of this type of construction are: I. The quadruple resistance or voltage compared with the top-bottom clamp resistor furnace. 2. Free expansion of the resistor. 3. The ease of protection from oxidation by air. 4. The firmness by which it may be held in the compact split clamp. This construction appeared to be well adapted for the fusion of high melting metals which require fusion in a vacuum. Zirconium metal had previously been melted at the Albany Laboratory of the Bureau of Mines in a vacuum arc furnace on a water-cooled plate, using a movable tungsten top electrode.2 When larger furnace capacities were desired, this type of construction proved to have its limitations as the largest tungsten rods available were about 7/8in. in diameter. The supply of direct current of high amperage for producing the . desired arc characteristics was also not available. Considerable difficulty was also found in compensating the atmospheric pressure on the flexible tubing of the movable electrode, at the same time keeping its movement sufficiently free to enable the striking of an arc on any part of the metal briquet. Among the various materials used for the electrodes in conducting experiments in the vacuum arc furnace was graphite. It was found that zirconium fused in a graphite cup with a carbon arc was contaminated to only 0.2 pct carbon. It was therefore decided to melt zirconium directly in graphite crucibles. A high-frequency furnace was first used in the attempt to melt the zirconium in graphite crucibles. The high-frequency heating coil was placed outside a silica tube which was evacuated by means of an oil diffusion pump backed up by a mechanical pump. The graphite crucible was thoroughly degassed at 1900°C before use. Considerable difficulty was experienced in operating at such temperatures in vacuo because, as shown by Zintl,3 carbon vapor formed and reacted with silica according to the reaction: Si02 + C = SiO + CO. The silicon monoxide which is volatile at these high temperatures reacted with the zirconium, thereby contaminating it with silicon and oxygen. The presence of carbon monoxide was detected by means of a gas discharge tube placed in the vacuum system as indicated by the pale blue glow of the tube as soon as carbon vapor started to react with the hot silica. The reaction between the carbon vapor and hot silica was avoided by the use of split cylindrical molybdenum shields which were inserted between the graphite crucible

Jan 1, 1948