Search Documents

Steps were taken for a permanent organization of the scientific and technical employees of the Government at their mass meeting on May 8. This was the result of an informal meeting on Apr. 23 of thirty representative Government scientists and technical men who organized the preliminary committee and called the mass meeting. This subject has been widely discussed during the last year and was brought acutely to the fore by the work of the Joint Congressional Reclassification Commission, because that Commission has stated that it wished to deal with employees only through organizations. Rodney H. True of the Department of Agriculture was Acting Chairman. He pointed out that the principal advantages that were expected to be derived from such an organization were: (1) Improvement of conditions and facilities for more effective scientific and technical work; (2) adequate presentation of the needs. and results of such work to the public and to legislative and administrative officers; (3) -greater freedom in both official and non-official activities; (4) just and reasonable salaries based on service performed and the economic and social conditions which prevail; (5) greater public recognition of the aims and purposes of research; (6) advancement of science and technology as an essential element of national life. Three plans of organization were offered to the meeting, which covered the fundamental principles which could be utilized by these Government employees. The first plan would have permitted the new organization to work only through existing scientific organizations. This is the plan that scientific and technical Government employees in England have adopted and an outline of the English plan was read to the meeting.

Jan 6, 1919

By J. A. Faucher

The mining industry has undergone significant technological advances in metallurgical process methods in recent years. The 1000 tpd concentrator of St. Lawrence Colum-bium Metals Corp. portrays the continuing effort made by the industry to achieve economical concentration of new and difficult ores. During the active search for sources of uranium in the early fifties, radioactive minerals were found in the Oka district near Montreal. The compatatively small quantities of uranium which were found occurred in association with widespread columbium (niobium) mineralization which included perovskite, a calcium titanate containing roughly 40% Cb2O5; niocalite, a silicate containing some 20% Cb2O5; and pyrochlore, a calcium niobate containing 45 -70% Cb2O5 as well as fluorine and some water. An idealized formula for one type of pyrochlore is: A typical chemical analysis of pyrochlore is shown in Table I. An important feature of this analysis is the lack of tin, lead, sulphur and P2O5 which conforms with the requirements of most consumers. In general the cerium content varies with sodium content and any increase in Ta2O5 lowers the Cb2O5 content of the concentrate. However, Ta2O5 rarely exceeds 0.5%. The carbonatite host rock of the columbium mineralization has the average mineral composition shown in Table 11. In Table 11, the term "diopside" is used to cover all silicates except mica which is shown separately because of the problems involved with its separation during the concentration process. In some ore zones, small quantities of rare earth minerals, such as monazite are present.

Jan 1, 1964

By W. J. McKenna

THE International Smelting Co. concentrator at Tooele, Utah, first operated on a custom basis for the treatment of lead-zinc-iron ores on Nov.' 1, 1924, with a capacity of 500 tons per day. On May 1, 1925, the capacity was increased to 1000 tons per day by the addition of another 500-ton section. The concentrator has since operated on the two-section basis, each treating 500 tons per day entirely by flotation. LABORATORY AND TEST MILL In connection with the concentrator, a well-equipped laboratory and small continuous testing plant are maintained. The flotation equipment in the test plant is of both the Callow and Mineral Separations Sub-"A" types, so that actual concentrator conditions may be duplicated as closely as possible. PURCHASING OF ORE A new shipper usually sends to the plant a 25 to 50-lb. sample, representative of the ore to be shipped. Batch flotation tests are made on this sample to determine its amenability to the concentrator treatment flowsheet and reagent combinations. The results of these tests, which are accurately correlated with those obtained at the concentrator, both as to grades of products and recoveries, determine the actual value of the ore as submitted in the ore purchasing department's treatment schedule. Hearty cooperation has existed at all times between the ore purchasing and operating departments in the selection of ores as concentrator feed. ORE TREATED The basic tonnages for mixtures on the two sections come from the Park City and Bingham mining districts. The Park City tonnages are received by rail and consist of crude ores and gravity mill products. Those from the Bingham district are received by rail and aerial tramway,

Jan 1, 1928

By Joseph Hartshorne

For something over two years past a new development of the open-hearth process has been in operation at the works of the Prager Eisenindustrie-Gesellschuft at Eladno, in Bohemia. It was devised and perfected by Mr. Ernst Bertrand, general superintendent,, and Mr. Otto Thiel, steel-works superintendent. The results which the inventors wished to obtain were to increase the product per furnace, to reduce the amount of refractories and additions used, to enable a poorer and more varied quality of stock to be employed, to improve the quality of the material produced and to render the control of the operations and product more certain. In all of these objects they have been successful, and have thereby considerably reduced the cost of manufacture and increased the value of the finished material. The Plant. The plant at Kladno consists of one 12-ton and one 20-ton furnace. Through an incident of construction the smaller furnace stands some distance behind and to one side of the larger furnace, and at a height of about 10 feet above it. The furnaces are in the same building as the Bessemer converters, and the metal is handled in the same casting-house by means of a locomobile ladle-crane. The relative position of the furnaces suggested the experiments by which the process was developed, and also enabled it to be thoroughly tested. Much valuable and practical work has been done in this plant, although it is not as convenient and suitable as one especially designed for the process would be. Nevertheless, the pecuniary and technical results have warranted its continuous operation. The Process. The process, as at present carried out at Kladno, consists

Jan 1, 1897

By John Metz, D. E. Macdonell

The Falconbridge ore body, on the southeastern periphery of the Sudbury Basin, is definitely associated with a strong shear zone along the norite greenstone contact, in contrast to the "offset" ore bodies sometimes found in this district. To all practical intent and purpose, the dip is vertical. The ore varies in width from a few inches up to 90 ft., the average width being 15 ft. The present zone of mining operations is 6000 ft. long, 85 per cent of which develops commercial ore. The ground on the whole, and especially in the narrower widths, gives rise to reasonably strong self-supporting backs in most places, but the walls, because of strong post ore faulting on both norite and greenstone contacts, tend to be weak, and, at times, slough to a considerable extent. Obviously. then, with vertical dips, strong backs and weak sloughing walls, flat-back cut-and-fill methods are applicable to the Falconbridge ore body, and at present about 70 per cent of the stoping production is obtained in this way. The general method is described in the following pages. In actual practice, there are continual variations, as the mine staff feels that only in that way can new and better methods be developed. Source of Fill The overburden at the property consists of glacial sands and gravels, varying in depth from 00 at the outcrops, which are few and far between, to 150 ft. This condition makes for high initial cost of shaft sinking, always entailing spiling and concrete, but this extra expense is more than compensated for by the fact that the overburden is the source of very cheap fill.

Jan 1, 1946

By William Griffith

THE purpose of this paper is to make public record of new information in regard to the sustaining power of artificial mine-roof supports (not timber props) the result of investigations recently made in the anthracite coal fields of Pennsylvania. First.-By the "Scranton Mine Cave Commission," appointed to investigate the mining conditions under the City of Scranton. Second.-By the "Pennsylvania Mine Cave Commission," appointed by the Governor to investigate the general subject of mine caves in the anthracite region of Pennsylvania. Third.-By the personal researches and tests made by the author in an effort to secure a better artificial mine-roof or surface support. During the progress of the work of the Scranton Mine Cave Commission, the Engineers for the Commission, Messrs. Conner and. Griffith, being aware of the general lack of exact information in the engineering profession as to the strength of the ordinary artificial mine-roof or surface support, and particularly the stronger kinds, such as mine cogs, rock piers, etc., had tests made at the. Fritz Engineering Laboratory at Lehigh University, to determine the sustaining power under various compressions of the several kinds of artificial mine supports in use in the anthracite region of Pennsylvania. A report of these tests was included in the report of this Commission, which was published as Bulletin No. 25 of the United States Bureau of Mines, Washington. A similar series of tests, more extensive and more elaborately-planned, were subsequently made for the Pennsylvania Mine Cave Commission at the U. S. Government Testing Laboratory at Pittsburgh, Pa. The report of this Commission was made to the Governor, but has not yet been published.

Jan 10, 1917

By J. L. Weeks

THERMAL conductivities of several samples of uranium and uranium alloys were determined using an apparatus previously described.' The value previously reported for uranium,' 0.035 cal per sec per cm per "C at 70°C, is in error due to the failure of a thermocouple during the determination on uranium. The defective thermocouple was detected after a reanalysis of the data obtained during the run and since has been replaced. Subsequently, runs on several samples of uranium show the thermal conductivity of uranium to be 0.069 cal per sec per cm per 'C at 70°C. The accuracy of the determinations was checked by measuring a sample of synthetic sapphire whose thermal conductivity was previously reported and found to be in agreement with other values."-" The values given in Table I are believed correct to % 3 pct or 0.003 cal per sec per cm per "C, whichever is larger. The samples were provided by J. H. Kittel of the Argonne National Laboratory, Metallurgy Div. References J. L. Weeks and R. L. Seifert: Apparatus for the Measurement of the Thermal Conductivity of Solids. Review of Scientific Instruments (1953) 24, pp. 1054-1057. J. L. Weeks and R. L. Seifert: Note Regarding the Thermal Conductivity of Synthetic Sapphire. Journal American Ceramic Society (1952) 35, p. 15. :' J. Francl and W. D. Kingery: Thermal Conductivity: IV, Apparatus for Determining Thermal Conductivity by a Comparative Method; Data for Pb, Al2O3, BeO, and MgO. Journal American Ceramic Society (1954) 37, No. 2, Part 11, pp. 80-84. (Part 11: special issue on thermal conductivity.) ' W. D. Kingery, J. Francl, R. L. Coble. and T. Vasilos: Thermal Conductivity: X, Data for Several Pure Oxide Materials Corrected to Zero Porosity. Journal American Ceramic Society (1954) 37, No. 2, Part II, pp. 107-110. (Part 11: special issue on thermal conductivity.) Edwin Ruh: New Jersey Ceramic Research Station, Rutgers University. Private communication.

Jan 1, 1956

By E. H. Griswold

The efforts of petroleum production engineers during the past year have largely concentrated upon ways and means of reducing operating investments and expenses in order that the industry may survive a period of low crude oil prices. Major progress was made in outlining and solving the technical problems pertinent to unit operation in order that executives and legal staffs may actually arrange operating contracts to effect unit operation. Consequent savings in development and operating costs, accompanied by increased recovery, will thus be obtained. Well spacing has received considerable constructive thought and study, from which practical results are assured in the near future. The control of edge and bottom waters has advanced in technique through the engineering work done in Yates, Hobbs and East Texas, and there is evidence of greater cooperative efforts between engineers to increase recovery from pools by mutual gas conservation. The use of pressure control by surface and bottom-hole chokes has become general practice to reduce gas-oil ratios. The study of bottom-hole pressures has led to new conceptions of proper utilization of reservoir energy and maintenance of pressure by natural means. Pressure gradients of flowing wells have been measured in practice and strides made to develop workable formulas for the flow of oil and gas mixtures through vertical pipes. The information thus obtained will permit the intelligent design of flow tubing combinations. Gas-lit and repressuring advancements have been few, due to overproduction from naturally flowing wells. Satisfactory unloading valves for gas-lift wells have been developed and consistent progress made in gas-lift displacement pumps. The necessity for producing wells at high rates of flow while producing large quantities of sand has resulted in radical changes in Christmas tree and separator designs for the Oklahoma City pool. The opening of wells to obtain potential production for proration purposes has been eliminated in the Yates and Hobbs pools by the application of engineering principles.

Jan 1, 1932

By P. Barnes

(Read at the Wilkes-Barre Meeting, May, 1877.) THESE furnaces are of the ordinary Siemens type, and present no special peculiarities of construction. The bed of each is 8 feet by 20 feet clear inside of the walls and ports. The producers are placed at a distance of about 200 feet from the furnaces, and the gas is collected in an iron tube and led across the yard overhead. It then drops underground into the gas flue, and is distributed to the furnaces. A considerable weight of floor-plates over the valve-pits is included in account 39, but none of the general stock of floor-plates for the mill were charged to the furnaces. In Table No. 1 is shown the money cost of the furnaces as distributed to the several accounts named. In Table 2 is shown the proportion of each account due to each of the several items or classes of expenditure named.

Jan 1, 1878

R. V. Norris, Wilkes-Barre, Pa. (communication to the Secretary*):—Mr. Stow's paper presents a series of arguments, numbered from 1 to 18, concerning the relative merits of four systems of colliery-ventilation, designated by the author as " plain pressure-ventilation," " plain exhaust-ventilation," " obstructed pressure-ventilation," and " obstructed exhaust-ventilation." These arguments are subsequently compared by means of tables, in which an arbitrary numerical value is assigned to each, and which consequently serve no other purpose than that of showing his opinions and predilections, as indicated by his assignment of the said numerical values. In addition to this general summary, Mr. Stow intimates his preference for a fifth method of colliery-ventilation—namely, what he calls " alternating pressure-ventilation," which consists in the running of the fan at "pressure " during working-hours, and as an " exhaust" between shifts—a system which he proposes as, perhaps, new, yet which he thinks deserves recognition " as a standard form." This proposed " standard form " is not to be found in practice ; and I think it would be impracticable in gaseous mines of large extent, for the following reasons: 1. It takes considerable time to reverse the air-current in a large mine; and the reversal would involve a period of complete stoppage of ventilation, long enough to permit serious accumulations of gas. 2. In shaft- and slope-mines, at least, it is hardly practicable to have " every man out of the mine" during the night, and certainly impracticable to avoid keeping mules and horses inside. 3. The doors necessary to divide and direct the air-current are properly hung to open against the air-pressure; and, unless

Jan 1, 1910

By Robert H. Richards

My first paper, read at the Cobalt Meeting of the Institute,' July, 1907, dealt with the behavior of a small Wilfley table when collceiltrating galena from quartz, the table being fed with natural products, with sized products, and with classified products. Since galena, having a specific gravity of 7.5, is among the heaviest minerals ordinarily concentrated by Wilfley table, it was desirable that a similar set of tests upon a mineral of lighter weight should be made. Chalcopyrite, of a specific gravity of 4, would have been the best mineral for this purpose, on account of its great importance as an economic mineral, but in carrying out the test I was obliged to content myself with a cupriferous pyrite, the specific gravity of which was 4.68 and the content in copper 8.80 per cent. Through the kindness of H. 0. Cummins, this material was obtained from Shasta, Cal., in very pure, clean, homogeneous condition. It was broken by rolls to 2 mm. in size, taking care to make a minimum of slimes. The quartz used to mix with it was pure, white, New England quartz, broken in the same way to the same size. In studying the accompanying tables, it should be borne in mind that the material concentrated was of low copper-content, and in many cases the quantity fed to the machine was 1 kg. or less. As a consequence of the smallness of the quantity treated it was very difficult to adjust the table and get it in condition to do its best work before the feed became exhausted, and for this reason many results were obtained which appear irregular.

Jan 1, 1909

F. E. BACHMAN, Port Henry, N. Y. (written discussion*).-Experi-ments with titaniferous ores found in Essex County, New York, made by the MacIntyre Iron Co. in 1914, showed' that titaniferous concentrates are reduced in the furnace with no greater, and probably with less, expenditure of heat, and consequently of fuel, than non-titaniferous mag-netites; and as a greater proportion of their oxygen is removed by carbon monoxide than is the case with non-titaniferous magnetites, a lower fuel consumption for the reduction of iron may be expected. After the furnace was blown out at the end of the experiment, the formation in the hearth was found to be abnormal. The brickwork was replaced, entirely around the furnace, by a layer which at -the tuyere circle was made up of cinder, fine carbon, and coke; the coke, however, gradually disappeared toward the bottom, being replaced by cinder and graphite. The usual salamander of graphite and iron was missing. The material left in the hearth seemed to be cinder that had not drained from the last cast; its composition, though, would indicate that it was in the furnace previous to the taking off of the titaniferous ore. At first, this material was thought to be blast-furnace cinder mixed with less iron and graphite than is normal; but an examination showed it to be made up of cinder with small masses of iron and graphite. There were also patches of a steel-gray material having a metallic luster; a microscope showed these patches to be made up of black metallic crystals interlacing white crystals.

Jan 11, 1919

By G. G. Sarkar

SHARPNESS of separation and washing efficiency are often confused. The sharpness index indicates the precision of a washing unit; the washing efficiency takes into account not only the unit's precision but also the washability characteristics of raw coal and the near-gravity materials at the effective density of cut. A sound basis for evaluating the sharpness index is essential in comparing the sharpness of separation attained by different cleaning units. Sharpness Index and Related Criteria: Washing plant sharpness of separation has been well represented by Hancock's efficiency chart and Tromp's curve of migrated materials. Some useful coefficients derived from Tromp's curve-the error area, probable error, and imperfection value-have been widely used to measure sharpness of separation. These are defined in a number of papers presented at the first and second International Coal Preparation Conference held in Paris (1950) and Essen (1954).1-5 In evaluating the performance of a dense medium separator at four different gravities, Yancey and Greer6 observed that even with similar operating conditions and the same size grading of feed, the imperfection value of a washing plant varies through a greater range than the probable error. The present writer also observed the same type of anomalies in comparing the imperfection values of one plant which were determined under almost identical conditions. He therefore devised a graphical method to evaluate a washing unit's sharpness of separation and define it by a single coefficient, which is substantially independent of coal characteristics under normal operation of the unit. Unlike imperfection value, the new coefficient can be expressed on a percentage basis.

Jan 12, 1957

By R. L. Robinson, P. DeFrank, R. F. Hatfield

Production equal to or greater than open-hole completions is possible through perforated completions if the flow paths throughout the perforations are free of obstructions.' Previous investigations have indicated that, in some cases, maximum productivity is not obtained due to plugging of the perforations with debris from the wellbore fluid and/or debris from the perforating process. Control of wellbore fluid and proper well completion techniques are very important in the elimination of perforation plugging.' Selection of properly designed perforating equipment also is quite important for maximum well productivity. Studies made with the use of the perforation flow laboratory, in which perforating tests are run under simulated well conditions, have shown that perforation plugging occasionally occurs. Plugs in perforations result from various causes. One of the contributors to plugging that can be controlled by the perforating device is the slug or carrot resulting from jet perforating. This condition has undergone extensive study, and previous developments have resulted in a decrease in carrot size—but not in complete elimination. It was felt that, if a method of completely eliminating the carrot could be found (with charge performance equal or better than previously obtained), a significant contribution would have been made. Such a charge has been developed and is reviewed in this paper. THEORETICAL CONSIDERATIONS OF CARROT ELIMINATION There are several popular theories of how a shaped charge jet is formed."," One of these is the hydrodynamic theory, wherein the liner is treated as a fluid under the impact of the explosive forces. Another is the spalling theory, where the interaction of shock waves in the liner causes small particles to be torn from the inner surface of the liner and projected at high velocity toward a common focal line to form the jet. It is not unreasonable to assume that both of these theories may be partially correct. For purposes of our discussion, it is simpler to use the second theory. Generally speaking, when a plate of metal is attacked by an explosive shock pulse, the pulse is transmitted through the metal at high velocity, as shown in Fig. 1(A). Pressures at the shock front may be 6 X 10' psi or higher. This shock wave (a compression wave) upon striking a free surface, Fig. 1(B), is partially reflected back as a tension wave. The interaction of the tension wave with the decaying compression wave causes a stress concentration in the metal; when this stress becomes great enough, a failure occurs and a small particle flies off and is projected away from the metal surface, as shown in Fig. 1(C). A new free surface is then presented to the shocks; the process repeats itself until there is no longer enough energy to cause failure, leaving a portion of the metal relativcly untouched. See Fig. 1(D). To apply this theory to a perforating shaped charge, consider the flat plate to be folded into a somewhat conical shape, with a column of explosive placed in intimate contact with the cone (Fig. 2). An explosive initiator detonates the charge, creating a shock wave

By Basil B. Zavoico

The developments in the Russian oil industry during 1935 marked a very definite turning point from the time when the industry was being educated to the modern methods of oil-field finding and development, refining, transportation and marketing, to the time when the industry has thoroughly assimilated the modern technique and is now firmly standing on its own feet, as is shown by the remarkable qualitative, if not quantitative, progress in 1935. The oil industry promises that 1936 will be a record year in every respect with both quantity and quality approaching the desired high levels and standards. More particularly the Soviet Government is beginning to be successful in the development of new fields and such new production in geographically strategical points of the country will be in the coming years a factor of great importance in the industrial life of the country. The most notable achievements of the last year have been: the very successful development of the Ishimbaevo oil field in the Lower Oural-Permian Basin; the discovery and development of several promising oil fields in the Puta district of Azerbaijan, while large flush production of Baku area was extended 50 miles due southwest into the Saliani-Aliat district, where a 3000-bbl. well was completed early in 1936 at Pirsagat. Also, an apparently important discovery was made at Zikh, on the Apsheron Peninsula proper. These discoveries, as well as several important strikes in the deeper producing sands in the older fields of the Apsheron Peninsula, have greatly augmented the proven reserves of Russia and made them available either at the points where transportation facilities were already present or at points not too far distant from major industrial centers of the country. Of course, not all objectives were achieved during the past year, and several major difficulties remain to be solved in the coming years, the more important of which are: (1) supply of equipment and of parts; (2) the unavailability of competent technical men in sufficient numbers, which more particularly affects the distant fields; and (3) the problem of distribution of oil products throughout the country, especially the question of handling the needs of small consuming areas, which, while individually unimportant, in the aggregate require huge distribution.

Jan 1, 1936

By Basil B. Zavoico

The developments in the Russian oil industry during 1935 marked a very definite turning point from the time when the industry was being educated to the modern methods of oil-field finding and development, refining, transportation and marketing, to the time when the industry has thoroughly assimilated the modern technique and is now firmly standing on its own feet, as is shown by the remarkable qualitative, if not quantitative, progress in 1935. The oil industry promises that 1936 will be a record year in every respect with both quantity and quality approaching the desired high levels and standards. More particularly the Soviet Government is beginning to be successful in the development of new fields and such new production in geographically strategical points of the country will be in the coming years a factor of great importance in the industrial life of the country. The most notable achievements of the last year have been: the very successful development of the Ishimbaevo oil field in the Lower Oural-Permian Basin; the discovery and development of several promising oil fields in the Puta district of Azerbaijan, while large flush production of Baku area was extended 50 miles due southwest into the Saliani-Aliat district, where a 3000-bbl. well was completed early in 1936 at Pirsagat. Also, an apparently important discovery was made at Zikh, on the Apsheron Peninsula proper. These discoveries, as well as several important strikes in the deeper producing sands in the older fields of the Apsheron Peninsula, have greatly augmented the proven reserves of Russia and made them available either at the points where transportation facilities were already present or at points not too far distant from major industrial centers of the country. Of course, not all objectives were achieved during the past year, and several major difficulties remain to be solved in the coming years, the more important of which are: (1) supply of equipment and of parts; (2) the unavailability of competent technical men in sufficient numbers, which more particularly affects the distant fields; and (3) the problem of distribution of oil products throughout the country, especially the question of handling the needs of small consuming areas, which, while individually unimportant, in the aggregate require huge distribution.

Jan 1, 1936

By H. E. Rorschach

Activity in Oklahoma oil fields made 1937 one of the best years since 1926. During the year, 3454 wells were completed, an increase of about 25 per cent over the year 1936. Purchasers reports filed with the Corporation Commission of the State of Oklahoma showed a total of 221,842,-788 bbl. of oil purchased from leases in 1937, an increase of about 10 per cent over 1936. The assembly of a complete table of all of the oil fields in Oklahoma has not yet been achieved. Many of the early records of operators and pipe-line companies are incomplete. Table 1 includes all of the new fields, and this year there has been added work done covering pools discovered in previous years, so that most of the important fields in the state of Oklahoma are included therein. The outstanding development of the year was the discovery of the producing horizon classified as the Wilcox in western Payne County by the Mid-Continent Petroleum Corporation on a unitized block in sec. 18, Tp. 18 N., R. 2 E. This block is operated hy the Mid-Continent and owned in conjunction with the Carter Oil Co., Transwestern Oil Co. and Sinclair-Prairie Oil Co. Another important development of the year was the extension of the deep zone in the old Fox-Milroy area of Carter and Stephens Counties. Some of the other discoveries made during the year 1937 are South Cromwell, discovered by Sinclair-Prairie Oil Co.; Cromwell extension of the Fitts pool in Pontotoc County; discovery of the Langston area in Logan County; discovery of the Sporn area in Lincoln County by Skelly Oil Co. and the discovery of the North Wellston area in Lincoln County by Standard Oil & Gas Co. Table 2 shows the new oil areas discovered in Oklahoma during the year 1937 and areas that were discovered in 1936 but developed in 1937. Fox-Milroy Area.—Three wells were completed to the deep producing zone during the year. One of the wells completed in the early part of the year uas the Carter Oil Company's No. 1 Harley in sec. 24, Tp. 2 S., R. 4 W., 3 1/2 miles northwest of the original discovery well, the Ruth

Jan 1, 1938

By W. E. Gaby

THE form of dip chart here presented for the use of the profession was devised by the author when he was confronted with a particularly heavy job of geological section making and. did not have any of the usual tables or charts at hand. This was at the property of the Teziutlan Copper Co. in Puebla, Mexico, where the orebodies are much faulted and lie conformably with a slightly inclined and. much folded schist. Because of the low dip and the folding of the orebodies, the engineering, and geological data respecting them were best represented on vertical cross-sections quite closely spaced. A less finished form of the chart was published in the Mining & Scientific Press of Aug. 6, 1921, with an explanation of its use. I have checked the new drawing for accuracy against the calculated table given, and constructed an explanatory diagram beneath. As some geologists are accustomed to using the table, I have included it, since no advantage is obtained by mere interpolations from the chart to get the required angle, except as it gives a mental picture of this angle. The chart gives a more rapid and much easier solution when cases multiply so that it becomes desirable to eliminate the tedious manipulations of a separate protractor. In fact, using the parallel ruler as des-cribed, it is not even necessary to make note of the angle sought. It is brought out graphically, leaving the mind free to note the correlations. The chart itself may be made more convenient by reproduction on celluloid with a slot running on the zero line of the protractor.

Jan 9, 1922

By J. H. Slater

THERE is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust con-tains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out, This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage, An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable prod-uct, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates.

Jan 1, 1940

By Henry A. Stiff

The classification and correlation of water analysis data presents many problems which can be solved by graphic methocis. The pattern system, a new type of graphic procedure described in this communication, is believed to have several advantages over older methods. Examples of the application, of the pattern system to the solution of problems encountered in petroleum production are given. INTRODUCTION Several graphic methods for presenting analytical water data have been developed and are now in use.1,2,3,4 It is believed, however, that a recently developed type of graph called the "pattern" offers several advantages over other methods. This system presents a better picture of the total salt concentration than is usual in such graphs. The effect of dilution or concentration has been reduced to a minimum, and at the same time distinction between various types of water has been improved. The system is extremely versatile, yet so simple it can be plotted on ordinary graph paper and adapted to almost any type of filing system. DISCUSSION The essential feature of the pattern system is the graph shown in Fig. 1. Horizontal lines extending right and left from a vertical line at zero form the graph. Positive ions are plotted to the left while negative ions are plotted to the right. The figure immediately beneath each ion gives the scale. Most oil field waters can be plotted on a scale where 100 milli-equivalents of sodium and chloride and 10 milliequivalents of each of the other ions are represented by one scale unit. For highly concentrated brines, 1,000 milliequivalents of sodium and chloride and 100 milliequivalents of each of the

Jan 1, 1951