Search Documents

By João Luiz do Vale

In standard wear tests, such as pin on disk (ASTM-G99) or block on ring (ASTM-G77), the apparatus simulates conditions that are often different from a machine element real application. Therefore, for an accurate investigation of a tribological application, it is essential to test the real condition in which there are similarities as: geometry, contact details, force application mode, materials, among others. It emphasizes that for studies involving polymeric materials it becomes extremely relevant. Thus, the Laboratory of Surfaces and Contact (LASC) at UTFPR developed an apparatus for sliding bearing on shaft test. In that equipment, loads are applied by a dead-weight system and the frictional force is measured on a load cell. The apparatus operating ranges for load added to the dead weight system and rotation shaft are from 0.2 to 5.0 kgf and from 260 to 3500 rpm, respectively. This paper presents a detailed evaluation of such apparatus, which includes free-body diagrams analysis and a deduction to obtain an equation for the kinetic friction coefficient. Also, the standard measurement uncertainties of a caliper, an electronic scale, and a cell load were determined. It was verified that the kinetic friction coefficient equation is dependent on the apparatus geometry, the applied load, and the frictional force value. Additionally, through the statistical significance analysis it was concluded that some terms in the equation were not significant. Finally, through the application of the error propagation theory in the kinetic friction coefficient equation, the standard measurement uncertainty of the apparatus which showed a value nearby 0.002 along the operating range of the apparatus was obtained.

Jul 31, 2018

By Lucas Faccioni Chanchetti

A utilização do hidrogênio em Células a Combustível para a geração de energia embarcada é uma alternativa promissora para o futuro da indústria automobilística, uma vez que o sistema é eficiente, possui alta densidade energética e é ambientalmente limpo. No entanto sistemas avançados para o armazenamento do hidrogênio são necessários, já que este possui uma densidade baixíssima. Entre as principais opções pesquisadas estão os hidretos à base de magnésio. Neste trabalho foi feita uma análise das patentes depositadas no mundo sobre estes materiais, mapeando os principais atores, evolução estocástica e as tendências tecnológicas do setor. Foi encontrada uma queda expressiva no patenteamento após 2008, o que pode sugerir um início de estágio de amadurecimento tecnológico, além de menos de 10% das famílias de patentes terem sido depositadas no Brasil, o que parece indicar que este não é visto como um mercado promissor para a tecnologia.

Aug 8, 2018

By Marjorie Benegra

This study aims to compare the wear resistance assessed in rubber wheel abrasion test of nickel aluminide coatings deposited by for Plasma Transferred Arc (PTA) and High Velocity Oxigen Fuel (HVOF) manufacturing, using the same raw material. A nickel aluminide powder was atomized and deposited on 316L steel plate substrate. After deposition, some specimens were submitted to a heat treating (1200 °C for 24 h followed by 760°C for 24 h). The coatings deposited using PTA developed different microstructures due to the incorporation of substrate elements, its performance was better than the HVOF coatings, although their Vickers hardness was similar. After heat treating, a significant variation in hardness and wear resistance was observed. For PTA specimens, there were decrease in hardness of 35%, while for HVOF ones this drop was approximately 20%. Nonetheless, the effect of thermal exposure in wear resistance was quite different: an increase of 21% was observed for HVOF coatings, while a reduction of 20% occurred in PTA ones. Microstructures modifications in PTA coatings were significant for their wear resistance. On the other hand, the reduction of porosity and sintering were responsible for a better performance of heat-treated HVOF coatings.

Jul 31, 2018

By Fábio de Oliveira Braga

A proteção balística contra projéteis de alta energia, como o 7,62 mm, é mais eficientemente realizada por meio de sistemas de blindagem multicamada (SBM). Estes são formados, em geral, por uma camada frontal de cerâmica, uma camada intermediária de tecido sintético ou de compósito, e uma camada posterior de um metal dúctil. Em trabalho recente, Monteiro et al. (2016) estudaram um SBM com camada intermediária formada por compósito reforçado com tecido de rami em substituição a um laminado tecido de aramida. Eles obtiveram resultados satisfatórios com boa redução de custo. No presente trabalho, foram investigadas fibras de rami in-natura como substituição ao tecido de rami na camada intermediária compósita. Os resultados foram comparados ao desempenho de um compósito reforçado com 30% de tecido de aramida, bem como aos resultados anteriores. Observou-se que a utilização dos compósitos reforçados com fibras de rami manteve o bom desempenho do SBM, com um custo cerca de 5 vezes menor que o SBM com aramida, e 60% menor que com tecido de rami.

Oct 30, 2017

By Martim Hideki Nakayama Kurauchi

One of the main issues regarding the use of charcoal in metallurgical processes is its mechanical strength, which is much lower than coke. There is no defined standard to determine charcoal compression strength, and the methods described in the literature consist in using a prepared specimen and applying compressing load in the same direction of the charcoal fibres. As charcoal is highly anisotropic, it is proposed a procedure that does not use a specimen and with load applied on a specific direction. Instead, it intends to simulate industrial conditions by randomly dumping charcoal inside a tube, without preferential directional arrangement. This is an attempt to determine charcoal mechanical strength and predict the behaviour of bulk charcoal under a static load, as in a blast furnace. Experiments with controlled loads have been carried out on randomly distributed bulk charcoal with controlled initial size and their effect on the size distribution has been analysed. After compression, charcoal is screened and each size is weighed, determining the particle size distribution of the experiment. This method can therefore be used to evaluate charcoal mechanical strength.

Aug 1, 2018

By Pedro Jorge Walburga Keglevich de Buzin

The steel production in mini mills generates several process residues, among them the electric arc furnace dust (EAFD). This residue has as main elements Fe, O, and Zn, being classified as hazardous by the presence of Pb and Cd. In recent years, a rise in the chlorine content of this residue was observed, motivated by the increased use of scrap with impurities bearing this element. In this work, a qualitative assessment of the presence of chlorine in the electric steelmaking process is made. Complementing it, theoretical considerations based on the computational thermodynamics tool FactSage show the effects of the chlorine on the mineral species in EAFD and on gaseous species in the gas phase (HCl and Cl2). For this study, PVC polymer was used as the chlorine carrier substance which contaminates the EAF charge; presence of other minor elements in the system such as K, Na and Pb were also considered.

Aug 7, 2018

By Giuseppe Pintaude

The use of two-dimensional shape parameters to characterize abrasive particles is a possible approach to express their angularity. Nonetheless, in sliding abrasion, especially in pin abrasion testing, coated papers structure plays an important role and even its damage during the wear process should not be neglected. This manuscript discuss the limitations of two-dimensional shape descriptors in distinguishing wear caused by relatively hard particles, indicating that the wear data obtained in sliding abrasion tests are unable to distinguish different types of coated papers used when only the two-dimensional particle projection is considered for shape characterization.

Jul 31, 2018

By Moisés Paulo Teixeira

The use of tailings for the synthesis of new materials is a worldwide concern today. This paper approaches the utilization of tailings of soapstone (steatite) in order to produce ceramics. The results show that the addition of soapstone in a ratio over 20% in the ceramic mass has enhanced the bending resistance of the ceramic samples when they were fired at temperatures of 900°C or 1000°C.

Oct 30, 2017

By Breno Totti Maia

This work was a continuous and multidisciplinary development. Through studies of the blowing process and its parameters results, evolutions, improvements and adjustments were made on the lance’s hot face with Slagless® technology, as well in the process parameters and mitigating actions of the projection of materials out of the converter. The main results are the increase in the nozzle’s life with a “record mark” of 1785 heats, and water leakage occurrence in the cartridge decreased considerably reaching the mark of one year without any occurrence.

Oct 30, 2017

By Paolo Demetlika

In this paper it is shown how the “Zero Operator” concept on the casting floor has been reached by adoption of a standard 6 axis industrial anthropomorphic robot coupled with the most innovative machine vision technology. This has been achieved by automating all the operations related to the ladle and tundish activities, including shroud manipulation, powder addition, ladle nozzle identification, nozzle opening by lancing, temperature measurement and chemical sampling. Q–Robot CAST family products are the result of the successful alliance between industrial robotics and the most advanced technology in process automation. This led, for each production area, to the introduction of flexible automation in dangerous places, even where some degree of human intervention is still necessary. By using anthropomorphic robots, human operators can be reassigned to safer environments. Furthermore, robots are suited to deal with repetitive and labor intensive tasks thus guaranteeing a high process quality.

Oct 30, 2017

By Henrique Lacerda Eleutério, Aldo Henrique de Almeida Barbosa, Vicente Tadeu Lopes Buono

The automotive industry’s interest in galvannealed (GA) boron steel for hot forming processes application has been steadily increasing due to its excellent surface quality, galvanic protection provided to the parts, good paint adhesion and better weldability in relation to other coatings for this application. In this study, samples of 22MnB5 galvannealed steel were heat treated and hot stamped on a water cooled die in laboratory scale. The influence of heat treatment on stability of coating and steel was assessed by using initial heating rates 11.0ºC/s and 15.0ºC/s. Microstructural evolution of galvannealed coating and structural integrity of steel during hot forming were investigated by scanning electron microscopy with energy dispersive spectroscopy analysis (SEM/EDS/Line scan), X-ray diffraction (XRD) and optical microscopy (OM). It was possible to quantify the Fe-Zn phase evolution during hot forming, to understand the effect of these heating rates on the product properties and to establish an optimized heat treatment for hot forming of these steel. The heat treatment with the heating rate of 15.0ºC/s presented greater operational flexibility and final products free from surface defects or cracks in the substrate.

Oct 1, 2019

By Cristiano José Scheuer

The effect of low-temperature plasma carburizing treatment on the micro-abrasive wear resistance of AISI 420 steel was investigated by mean of a CSM Calowear ball-cratering equipment. Carburized samples were treated at temperatures of 350, 400, 450 and 500°C for a fixed time of 12 h, using a gas mixture containing 99.5% (80% H2+20% Ar)+0.5% CH4. Micro-scale abrasive wear tests were conducted with a 25.4 mm AISI 420 steel sphere, using an abrasive suspension of alumina (Al2O3) with particle size of 1 ?m (abrasive concentration of 0.11 g/cm³). The contact normal force, abrasive flow and ball rotation speed were fixed at: 0.5 N, 0,2 drop/s, and 120 rpm. The wear craters were analyzed using a confocal laser microscope, Olympus OLS 3000. The wear analyses were performed for test times of: 30, 60, 90, 120, 180, 360, 540, 720 and 900 s (equivalent sliding distance: 0.84, 1.68, 2.52, 3.36, 5.04, 10.09, 15.14, 20.19 and 25.23 m, respectively). The results indicate that the wear coefficient in the outer layer and in the diffusion layer are different, being lower in the latter. It was also verified that the wear coefficient on the outer layer region decreases with increasing treatment temperature in the range of 350 to 450 °C, and increase again for 500ºC. The diffusion layer wear coefficient is similar for all the carburized samples. Finally, for all studied conditions, the analysis of the wear craters surface indicates the occurrence of grooving and micro-rolling abrasion wear modes.

Aug 8, 2018

By Roberto Quadros Menin

Os métodos de simulação estocástica permitem acessar o espaço de incerteza associado à estimativa de atributos geológicos. Esse espaço de incerteza, obtido através da geração de múltiplos cenários equiprováveis, pode ser utilizado para análise de risco e tomadas de decisões, de acordo com alguma função de transferência utilizada. Os métodos de simulação sequencial são amplamente difundidos para a construção destes modelos. Simulação sequencial gaussiana requer que a variável original seja transformada em uma distribuição normal. O método de simulação sequencial direta não necessita de alguma transformação anterior a realização das simulações, permitindo simular diretamente dentro do espaço original dos dados. A metodologia apresentada, neste trabalho, irá abordar as principais diferenças destas duas metodologias de simulação sequencial comparando os resultados. Simulação sequencial Gaussiana tende a reproduzir melhor o histograma, enquanto simulação direta é mais facilmente implementada, pois não necessita de nenhuma transformação dos dados. Os métodos serão ilustrados através de um estudo de caso.

Aug 8, 2018

By Božidar Šarler, Umut Hanoglu

A rolling simulation system has been developed to calculate the macroscopic rate of deformation, stress, strain, and temperature fields by using a novel meshless method. The model is based on two-dimensional traveling slice assumption. The slices are aligned towards the rolling direction. The initial size of the billet, bloom or slab and the geometry of the grooves at each rolling stand, the distances between the rolling stands, and continuous or reverse rolling can be arbitrarily considered. The purpose of this paper is to complement these development by predicting and visualizing also the grain size of steel over the strand cross-section for each position in the rolling mill. The grain size models have been in one-way coupled to the macroscopic calculations. First the critical strain for dynamic recrystallization is being checked. If the calculated strain is higher than that, considering also the time for meta-dynamic recrystallization, dynamic or meta-dynamic grain size calculations are carried out. If the strain is too low then only the static recrystallization is considered together with its required time. Finally, austenite grain size and ferrite grain size are calculated respectively as the steel cools down. The listed physical models are based on collection of empirical relations found in literature. The user of the system is free to choose or create the model he wants with his own parameters. The simulation system has been coded as a user friendly computer application for an industrial use based on C# and .NET framework and runs on regular PCs. The computational time for a rolling simulation is usually less than one hour and can thus be straightforwardly used for optimization of the rolling mill design in a reasonable time.

Oct 1, 2019

By Raúl Daniel López

Un objetivo de seguridad y calidad en los moldes de la colada continua de Siderar fue la de tener un menisco estable y controlado. A lo largo de los distintos periodos de inversiones y mejoras, el control de nivel de Siderar logro como objetivo contener su variación de nivel de acero en el molde en un rango de variación menor a +/-2 mm y con una velocidad de cambio inferior a 1,5 m/segundos. Esta etapa trajo una relativa mejora en los aspectos mencionados (calidad y continuidad operativa) pero el hecho de tener como sistema de medición de nivel un sistema radiactivo (fuente Co60 y contador de centelleo) mantenía serias limitaciones en ambos rubros dado que este sistema no diferencia la interface escoria /polvo colador con el menisco de acero. Este trabajo tratará de mostrar y contar las tareas de desarrollo y aplicación de esta nueva tecnología, hoy vigente en la nueva Colada Continua N° 2 (CCD2) y en etapa de puesta en marcha de la CCD1.

Aug 15, 2017

By Guilherme Dias da Fonseca

Com base nos modelos analíticos de Johnson e Mehl, Kolmogorov e Avrami (JMAK) e Cahn, no presente trabalho estudou-se via simulação computacional a cinética das transformações de fases no estado sólido. Tais transformações ocorreram numericamente por nucleação e crescimento nas interfaces de poliedros do tipo Ortotetracaidecaedros em um domínio discreto. O intuito da matriz de Ortotetracaidecaedros é aproximar-se das características fenomenológicas de uma rede perfeita de grãos no espaço amostral. Realizaram-se simulações de nucleação com posições aleatórias em toda a matriz (bulk). Em um segundo estudo foram realizadas novas simulações de nucleação aleatoriamente, porém somente nas interfaces dos Ortotetracaidecaedros. A quantidade de núcleos iniciais para cada caso foi definida por processo de ponto de Poisson. A fração volumétrica, a área interfacial entre material transformado e não transformado, a contiguidade e o caminho microestrutural foram os resultados obtidos através das simulações. Tais resultados foram comparados com as equações analíticas. As nucleações com até mil núcleos corroboraram com JMAK e foram ratificados com o comportamento da contiguidade e do caminho microestrutural. Já as nucleações com valores acima de mil núcleos, mostram a presença de clusters, apresentando uma boa concordância com o modelo analítico de Cahn.

Oct 30, 2017

By Adriano Alex de Almeida

Dois aços de grão não orientado com 2,45 e 3,3 %Si com 7 amostras para cada liga, foram estudados para compreensão do efeito do teor de silício nas perdas histeréticas. As amostras foram recozidas com diferentes temperaturas de recozimento final, resultando em diferentes tamanhos de grão. As perdas histeréticas e B50 foram medidos. Os resultados de B50 mostraram que não houve variação de textura entre as ligas com diferentes %Si. Por fim, os resultados não mostraram variações da energia dissipada pela perda histerética com adição de %Si.

Aug 7, 2018

By Helênio Resende Silva Junior

Em coquerias, o período compreendido entre o início de operação até a desativação devido final de vida útil é relativamente longo. Torna-se tarefa muito difícil determinar-se o tempo exato de desativação por degradação uma vez que as coquerias possuem muitos fornos tipo batelada e o grau individual de degradação varia de acordo com as condições operacionais e método de preservação aplicados. Apesar dos cuidados adotados na operação e manutenção das coquerias, torna-se inevitável um desgaste inexorável em suas estruturas com o passar dos anos, com progressivo decréscimo na capacidade eficaz de produção até a sua paralisação. Tendo em vista o elevado custo envolvido na construção de novas coquerias, torna-se prioridade para as siderúrgicas prolongarem ao máximo a vida útil das baterias existentes, adotando o tipo de reparo adequado a cada fase da vida da bateria. O presente trabalho tem o objetivo de descrever os tipos de reparo em baterias de coque disponíveis, visando restaurar as estruturas e recuperar a capacidade produtiva das coquerias, respeitando as normas ambientais vigentes.

Aug 16, 2017

By Daniel Wild, Tobias Scheffer, Marvin Laugwitz, Martin Jochum

Leveling is a standard process in the rolling mill to eliminate flatness deviations. The process layout is based on models and the leveling result depends on the accuracy of the material parameters in these models. Even small deviations from the correct assumptions can have a major effect on the final flatness. Thus, after leveling the products may look optically flat, but subsequent to a final cutting process springback occurs due to residual stresses. The objective of this work is to analyze the influence of material parameters and gravity on the flatness after leveling. To evaluate the sensitivity of the process, an FE parameter study is exerted that reveals the influence of fluctuations in material properties in the case that the leveling setup is fixed. Gravity is neglected to not conceal flatness deviations. Examples of this study are rerun in a further step under consideration of gravity to also analyze its influence on the resulting flatness and residual stresses. Finally, to analyze the consequence of the residual stresses, all information of the plate from the previous step are transferred while gravity is suppressed to prompt springback. This study revealed that slight deviations of the material properties can lead to uneven plates in simulations where gravity is not considered. If gravity is taken into account, the unevenness is concealed and the plate seems flat. A springback simulation of the same plate shows that strong residual stresses are still present and would lead to unevenness if e.g. the plate were cut.

Oct 1, 2019

By Leandro de Arruda Santos

O objetivo deste trabalho é contribuir no desenvolvimento de novas soluções para a terapia endodôntica através do uso da análise por elementos finitos para avaliar o comportamento mecânico de instrumentos endodônticos. Primeiramente comparou-se os resultados de testes de flexão e torção com simulações realizadas sob as mesmas condições para validação. Uma vez validada a metodologia, pôde-se avaliar o comportamento de uma lima de NiTi CM em comparação a outras duas de aço inoxidável e NiTi superelástico com mesma geometria. As geometrias de dois instrumentos endodônticos comercialmente disponíveis foram submetidas a microtomografia computadorizada para a construção de modelos 3D. A malha de elementos finitos em ABAQUS e as condições de contorno foram baseadas em ensaios experimentais de flexão e torção de limas. Os modelos constitutivos foram obtidos a partir de curvas tensão-deformação em fios de NiTi superelástco, NiTi CM e aço inoxidável. Os resultados mostraram uma boa concordância entre resultados experimentais e simulados. O instrumento de NiTi CM apresentou-se como o mais flexível em comparação aos instrumentos de NiTi superelástico e aço inoxidável.

Aug 16, 2017