Search Documents

By Bruno Pinheiro Silva, João José dos Santos Carvalho, Flávio Túlio Busatto, Leonardo Passos Perdigão

Sinter has high participation in the blast furnaces ferrous burden in ArcelorMittal Tubarão, being therefore of paramount importance the constant control of its physical, chemical and metallurgical qualities, aiming at the fulfillment of the client required quality. With the great challenges faced by market conditions, steelmaking companies seek operational sustainability, aiming at stability and reducing costs. One of the main steps to obtain these results in the Blast Furnaces is the raw materials quality stabilization, in order to guarantee the perfect burden distribution control and a better use of the reductant gas inside the reactor, aiming a lower fuels consumption. It is known that the smaller a ferrous particle is, better its reducibility, since a larger surface area provides greater contact with the reductant agent. Based on this concept, the objective of this work is to quantify the effect of the sinter size produced in ArcelorMittal Tubarão Sinter Plant in its reducibility, and in this way enable the definition of a better sinter particle size distribution aiming at a balance between the permeability effects and gaseous yield in the Blast Furnaces. In addition, the reducibility effects on sinter size reduction were evaluated, where the 5 to 10 mm fraction was analyzed in two sinter samples, the first obtained from the conventional route and the second after crushing of the fraction over 50 mm, in order to simulate the effect of the use of a Secondary Crusher in Sintering.

Oct 1, 2019

By Jose Pedro Gualberto Junior

Este estudo tem por objetivo analisar as causas de falha em cabo de aço utilizado na construção civil. Os cabos foram submetidos à metodologia de análise de falha. Foram realizadas inspeções visuais, análise de fratura em baixo aumento e em microscópio eletrônico de varredura, análise de microdureza, análise microestrutural em microscópio ótico e microscópio eletrônico de varredura e análise de resistência mecânica por ensaio de tração. Os resultados indicaram que os cabos sofreram severo desgaste e a ação da corrosão o que favoreceu a diminuição da resistência mecânica e a propagação de trincas planas por fadiga.

Aug 16, 2017

By André Tarcizo de Oliveira Vieira

A Companhia Siderúrgica Nacional (CSN) gera diversos resíduos metálicos de diferentes granulometrias que não podem ser utilizadas na rota natural da produção do aço. Este trabalho tem como objetivo descrever o pioneirismo do desenvolvimento e a implantação de melhorias no sistema de adição em carros torpedos que permitiram a utilização nobre de resíduos ricos em ferro, demonstrando a viabilidade técnica assim como a viabilidade econômica. A redução do consumo de energia é outro argumento para reciclagem de resíduos, neste contexto a CSN tem aumentado o interesse pela reciclagem devido a necessidade de diminuição de consumos energéticos e da consciência ambiental. O processo desenvolvido demonstrou a viabilidade da utilização de metálicos de pequena granulometria pela adição em carros torpedo, aumentando a oferta de ferro gusa líquido para os convertedores da CSN.

Aug 2, 2018

By Daniel Antonio Kapper Fabricio

Laboratórios realizam o ensaio para determinação da tenacidade à fratura KIC, mas para verificar a validade dos resultados, é importante que se estime a incerteza de medição do ensaio. O Guia para Expressão da Incerteza de Medição (GUM) apresenta um método reconhecido internacionalmente para se estimar a incerteza de ensaios quantitativos. O presente trabalho apresenta o desdobramento das etapas do GUM para o ensaio de KIC e a aplicação da planilha e do procedimento elaborados em um ensaio. Ao final, é realizada a análise crítica de quais fontes mais contribuíram para a incerteza de medição do ensaio executado.

Aug 8, 2018

By Vitor Guarnier Domiciano

The need to adjust the monolithic refractories to increasingly severe and unstable Blast Furnace casthouse operating conditions has been a major challenge for refractory suppliers in order to guarantee the runner’s safety and its availability for operation. This paper presents the properties of a new robust single line Al2O3-SiC-C refractory castable developed to endure the severe operating conditions that main runners are facing in today's Blast Furnace casthouse scenario. Practical results during almost one year of testing revealed a significant lower wear speed of the new refractory lining when compared to a standard product.

Aug 1, 2018

By Ruy José Feijó Alves

O policarbonato é um polímero quimicamente neutro, 100% reciclável, resistente a altas temperaturas, impermeável, durável que oferece uma combinação fantástica das suas propriedades físicas, químicas, mecânicas, térmicas e eléctricas (isolante eléctrico). O policarbonato é um dos plásticos de maior venda e que mostra a maior taxa de crescimento anual no mundo, devido às suas excepcionais propriedades e versatilidade de aplicação e uso. Devido à grande utilização de polímeros nas mais diversas aplicações ao ar livre, surgiu a necessidade de estudar sua resistência às intempéries, não somente por aspectos estéticos, como descoloração ou perda de brilho, mas também por mudanças nas suas propriedades. Os polímeros quando expostos a luz solar na presença de oxigênio são degradados, no entanto as taxas de degradação foto-oxidativa dependem fortemente da natureza química do polímero. Durante o processo de degradação ocorrem mudanças físicas e químicas no polímero que levam à descoloração, fissuramento, perda de brilho e queda de resistência mecânica. Tais fenômenos estão quase sempre associados a processos de cisão de cadeia e, em alguns casos, ocorrem também reticulações. Para se avaliar a estabilidade, ou mesmo avaliar a eficiência de um polímero, é necessário submetê-los a ensaios que simulem as condições às quais ele estaria exposto durante a sua vida útil. Nesse contexto será apresentada uma avaliação sobre a degradação do polipropileno exposto a radiação ultravioleta.

Aug 8, 2018

By Jefferson Lisboa Lelis, Marcos Roberto Soares da Silva, Maiara Rodrigues Gouveia

Nowadays, due the development of new hot rolled strips at USIMINAS, established the necessity of realizing studies to define new parameters for the welding machine of new pickling line, in order to improve mechanical and metallurgical properties of these materials. The aim of this study was to evaluate the weldability of high strength low-alloy steel with low boron content with tensile strength above 600MPa.The influence of energy input and preheating temperature on the mechanical properties of hot rolled strips were analyzed at three distinct thickness (2, 4 and 6 mm). To perform these evaluations were used tensile test, micro-hardness, metallography (micro and macro examination) and scanning electron microscopy analysis. In resume, a good welding performance was achieved, increasing preheating temperature and the welding energy higher than 60%.

Oct 13, 2019

By Jan Bak

Rourkela Steel Plant (RSP), which is operated by the Steel Authority of India Limited (SAIL), was inaugurated in 1959 and was the first Integrated Steel Plant in the public sector in India. In 2013, RSP commissioned their No. 5, 4060 m³ Blast Furnace, India's largest. It was built as a turn-key project by a consortium consisting of Danieli Corus and Tata Projects Ltd. and is entirely based on the technology and know-how of Danieli Corus. The new Blast Furnace is the key element of an expansion program that doubles the plant's production capacity and with much of the existing ironmaking capacity reaching the end of its technical and economic life span, it enables RSP to meet existing as well as growing demand for its products. This article discusses how this greenfield Blast Furnace was built in an existing and operating Integrated Steel Plant. It covers the accommodation of land, planning of the new installation to fit the available plot as well as the updated logistical lay-out of the plant. Technical details of the installation are presented, including their consequences for RSP's environmental performance and new perspectives for campaign planning.

Aug 2, 2018

By Rainer Fackert

3D-Measurements for slabs and heavy plate are now available and close the gap in the production chain. The measuring systems described in this presentation must be seen as high-tech solutions in the field of casting and rolling technology. The measuring systems were developed taking into consideration the harsh casting and rolling mill environment in which they are to be used, with the aim of achieving high operational reliability and eliminating disturbances. Interconnected quality management systems enable optimization across the complete production process. New limits are being defined constantly for all these developments. What is technically feasible today becomes normal practice tomorrow, and will probably be replaced by completely new technologies the day after.

Aug 16, 2017

By Luana De Lucca de Costa

Este trabalho é um estudo sobre os aspectos tecnológico de sinter forjamento, onde são realizadas alterações nos parâmetros temperatura e deformação. Experimentos foram realizados para o estudo das variações microestruturais, e propriedades, tais como, densificação e dureza, e, ainda, quais as variações na força empregada para obtenção das deformações estabelecidas. A relação entre a tensão de atrito na interface e outras variáveis do processo é discutida e uma análise feita para o cálculo da distribuição da pressão e carga a partir das equações de equilíbrio. Os resultados são discutidos e os parâmetros de processamento envolvidos durante o processo de sínter forjamento são analisados.

Aug 8, 2018

By Vitor Orlando Ferreira

The efficiency of an apparatus which uses a forced lubrication system, as well as the useful life of its components, is strongly related to the degree of contamination of lubricating oil. The presence of contaminants and the degradation of the oil itself cause it to release substances that fouling of the wall of the pipes. The cleaning and dialysis of the oil pipes, besides prolonging the life of the lubricant reduces wear of the components. There are several methods of cleaning in pipes, the problem is that some have abrasive characteristics, which could damage some types pipes. Among the non-abrasive methods stand the Flushing and Air scouring. Flushing uses the lubricating oil which circulates in temperatures alternating and high speeds, for generating turbulence to perform washing. The Air scouring method uses oil and filtered compressed air, injected into pipe, to generating higher flow, causing the power supply unit with fluid can work with lower power consumption and higher speeds, removing fouling of the pipe. The objective of this research is to evaluate the Reynolds number to correlate with the efficiency of cleaning the pipe. The method applied was the Air scouring and it was verified that the qualitative effects may occur when compared to Flushing. After testing, it was found that the chosen method brings significant changes in flow, and this flow regime varies considerably increasing the Reynolds number.

Jul 31, 2018

By Foluke Salgado de Assis

O presente trabalho tem como objetivo analisar as propriedades em blocos de cerâmica vermelha. O diferencial e originalidade em relação ao que já existe em termos científicos são as evidencias de que gradientes de umidade são mais significativos em secagem rápida o que provoca a presença de tensões residuais, como também em termos da porosidade em temperaturas de queima diferentes e conformação sob condições de presença e ausência de vácuo na produção dos blocos. Nestes casos, danos estruturais como trincas, deformações e fraturas podem surgir no produto final ou durante o carregamento de serviço devido à diminuição dos valores de resistência mecânica. Os resultados evidenciam que corpos de prova submetidos à secagem rápida em comparação a secagem lenta, bem como a diminuição da temperatura de queima e ausência de vácuo durante o processo produtivo, decrescem a propriedade mecânica citada..

Oct 30, 2017

By Edmar de Souza Silva, Antonio Augusto Gorni, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Controlled rolling followed by accelerated cooling, known worldwide as TMCP, aims to increase mechanical properties without toughness deterioration. The process principle is to promote the plate cooling with water jets along the range of the austenite transformation temperatures. The accelerated cooling process is only fully effective when controlled in an integrated manner, as it alone cannot ensure significant improvements in the final properties of steels. Plate surface quality depends on some parameters that must be controlled before the start of the plate accelerated cooling. Good flatness is essential to avoid irregular water accumulations during cooling. After the reheating process, the slab should have uniform temperature, uniform austenitic grain size and easily removable scale. The slab thermal and microstructural heterogeneities are inherited by the rolled plate and tend to increase further during the accelerated cooling. This results in flatness problems, high level of internal stresses and mechanical property variations. The descaling strategy is an extremely important factor and must be determined with great caution. It is important that scale thickness and distribution is uniform to ensure homogeneous cooling over the entire plate surface. Otherwise, there will be an uneven temperature distribution, which can cause serious problems of flatness, surface quality and mechanical properties.

Oct 1, 2019

By Josef Maierl

For the production of advanced high strength steel grades (AHSS) like API X80/X100, dual-phase, martensitic and complex-phase grades a number of hot strip mills need to extend their limits in terms of power and flexibility. Especially for cooling and coiling of these new materials, Primetals Technologies developed the “Power Cooling” and “Power Coiling” technologies. Power Cooling combines the advantages of conventional laminar cooling or “low pressure cooling” with the newly developed “high pressure cooling” with highest cooling rates for flexible operation. The Power Coiler which is needed to coil those high strength grades especially at thicker gauges ensures reliable strip-coiling for a most economical production. To enhance the reliable production of high-strength steel grades for a wide range of strip dimensions, the automation system with its advanced models is an integral part to the mechanical design. In this context the paper presents examples for the installation of power cooling and power coiling in new and modernized HSM.

Aug 16, 2017

By Weslei Viana Gabriel

Utilizando um sistema composto por solução aquosa e óleo como substitutos do metal e da escória, respectivamente, foram realizadas simulações físicas e matemáticas em molde de beam blank, de maneira a avaliar efeito da diferença de densidade entre os fluidos, viscosidade do óleo, velocidade de lingotamento e profundidade de imersão da válvula submersa. O aumento da velocidade de lingotamento resulta em aumento da velocidade na interface, bem como a oscilação da superfície livre. Para a densidade de solução aquosa igual a 1000kg/m3 observou-se entranhamento de óleo a partir da velocidade de 0,98m/min. Ao se aumentar a densidade da solução para 1170 kg/m3 não se observou entranhamento em nenhuma das condições estudadas..

Oct 30, 2017

By Jörg Schwelberger

Government regulations around the world concerning environmental care are becoming more stringent, also including regulations and restrictions of depositing and use of dust, sludge and slag generated in the iron and steelmaking process. With this scenario, by-products such as iron containing dust, sludge, oxide fines, mill scales and slag, become a valuable resource and recycling may be a profitable activity within a plant. Up to ten percent in mass of the total steel output of dust, sludge and mill scale by-product materials and more than 40% of slag by product are generated within an integrated steel plant with an iron content ranging from 50% to 65% for fines and up to 25% for BOF-slag. Slags are being widely recycled and used in the cement industry, as is the case for BF slag, and in the construction industry in the case of BOF slags and EAF slags. However, value of BOF unmodified slag is typically low and environmental regulations limit the usage of the unmodified BOF slag. This paper describes innovative solutions for recycling of fines using cold briquetting technology and the modification and granulation of slag from steelmaking that increase the value of the by-product and yield a marketable product.

Aug 16, 2017

By Alessandro Pigani

Over the last 25 years the thin slab casting and rolling process has been gaining a major market share in the production of hot rolled strip, progressively eroding the areas previously of exclusive domain of conventional mills. This is mainly thanks to the competitiveness of the process over conventional ones, and to the growing ability of this technology to cover the majority of market niches, well beyond the boundaries of the commodity market. After having significantly contributed to the continuous expansion of this production mode and after an extensive campaign of theoretical research and physical testing in reference plants, Danieli has progressively developed over the years a new generation of thin slab casting and rolling layout, marking a new phase in the evolution of this process. The new step-ahead is epitomized by the name QSP-DUE. This configuration belongs to the Quality Strip Production (QSP) family, which is Danieli’s strip-quality-oriented thin slab based plants. The innovative features of the process are embodied in the acronym DUE, which stands for Danieli Universal Endless (Danieli patented technology – US patent n. 8087449, January 3rd, 2012). What makes this new concept different is the ability of “universal” rolling modes thanks to the fact that, now, within one single plant it is possible to perform coil-to-coil, semi-endless and endless rolling modes, making this plant a major technology innovation compared to the previous generation.

Aug 16, 2017

By Manfred Hackl, Sergey Bragin, Alois Seilinger

The demand for hot rolled strip is growing in multiple ways. To remain competitive, new and existing mills must meet arisen challenges in the best possible way. The production of hot strip is a key element of steel production. Since close to half of all steel produced is hot-rolled to strip, mills require maximum throughput and availability combined with geometrical precision and the ability to create optimum material properties. Today there is a clear trend in developing new steel grades with high-strength and improved formability, like 3rd generation AHSS (Advanced High Strength Steels), as well as a trend to produce thinner and wider gauges. This trend challenges hot strip mills because it requires new technologies which provide more flexibility in metallurgical treatment during the rolling process. In order to meet and promote these trends Primetals Technologies is currently working on different concepts and solutions. One example is the development of a new mill stand technology Flex-HI HOT which allows to adapt the last finishing mill stands by efficiently switching from 4-high to a 6-high mode with small work roll diameter based on production needs. Another solution is to apply a permanent 6-high rolling stand at the end of the finishing train. A smaller work roll diameter allows to achieve higher specific thickness reductions and deformation rates resulting in significant thinner hot-strip gauges with valuable metallurgical benefits. The developed solution concepts with technological and metallurgical benefits will be presented in this paper.

Oct 1, 2019

By Sebastien Maillard, Stephane Georges, Thomas Vallee, Stanislas Mauuary

Steel strip manufacturing ever reinvents proposing new grades, requiring to tackle technical limitations of production systems. Primetals Technologies breaks through strip welding by expanding the welder LW21L “Asolid” technology used on low gauges for high-end market such as automotive CAL/CGL. Addressing the usual drawbacks in maintenance, operation and safety of current welding system based on mechanical cutting and CO2 laser welding, the newly developped LW21H “Asolid” technology processes thicker strips up to 7 mm with solid-state laser cutting and welding. This new welder is brought to reality through a scale 1:1 pilot developed, manufactured and tested in Primetals Technologies workshop.

Oct 1, 2019

By Mery Cecilia Gómez Marroquin

Um importante problema das indústrias de fabricação de aço, decorrentes do uso de sucata de aço, é o de recuperação dos metais contidos nos pós e lamas produzidos nos fornos elétricos a arco (FEA) e nos conversores LD/FOB. Cerca de 10 a 20 kg de pó por tonelada de aço são gerados nos Fornos Elétricos a Arco, considerados resíduos perigosos pelos órgãos fiscalizadores (classe ? - material perigoso/NBR). Vários processos, utilizando tecnologias distintas (pirometalúrgicas e hidrometalúrgicas), buscam a recuperação técnico-econômica principalmente do Fe e do Zn, contidos nesses resíduos. Neste contexto, estudos básicos sobre a redução carbotérmica dos constituintes dos pós de aciaria, permanecem sob estudo. O presente trabalho foca a redução de ferrita de zinco gerada em laboratório, principal composto de zinco presente nos pós de aciaria, por meio de CO puro e misturas CO-CO2. A fenomenologia da redução considera a decomposição prévia seguida de reduções simultâneas, bem como as significativas influencias da temperatura, do tempo e do teor de CO.

Aug 8, 2018