Search Documents

By Will B. Jamison

An ignition detection and suppression system was developed under the scope of this contract. The objective of this machine mounted system was to detect flames caused by frictional sparking from the cutting bits of a continuous mining machine and to suppress it with sufficient speed to prevent the development of an explosion, and to keep the flame from harming the machine operator.

Jan 1, 1976

By Mike Watts

Since the first longwall panel development started in the new mining, (Southern) area, a number of roof falls have occurred in L1 and L2 gate-entries. The longwall was delayed for a total of two months due to roof falls in the gate-entries. To prevent roof falls in future gate-entries, an extensive ground control analysis has been conducted which incorporated regional horizontal stress and panel orientation, tectonic stress, roof strata, surface stream valleys, etc. Results of the analysis indicate that a combination of these factors caused the roof falls. Therefore, a Roof Instability Rating (RIR) system was constructed to predict the roof condition and identify areas where supplemental support should be implemented. The L3 gate-entries, supported by the prediction using the RIR system, have not experienced any roof problems.

Jan 1, 2000

By H. B. Hill

The Lake Creek gas-condensate field, Montgomery County, Tex., Was discovered early in 1941 by the Superior Oil Co. The field, shown in figure 1, is approximately 37 miles northwest of Houston, Tex., about 11 miles north of the Tomball, and 10 miles west of the Conroe oil fields. The field is on the downthrown side of a pronounced fault zone, and the general structure is anticlinal, with the long axis trending northeast and southwest. Production is obtained from multiple sandstone reservoirs in the Wilcox group of Eocene age between the approximate depths of 8,820 and 11,840 feet below the surface of the ground.

Jan 1, 1948

By Dean Bray

During the past three years, a new rear-dumping dragline bucket technology has been patented, developed and tested at North Dakota coal mines. Field testing has shown that this new concept in dragline bucket technology can improve strip-mining efficiencies by reducing cycletimes and increasing dumping radius. This article details the process, participants and the results for the development of a rear-dumping dragline bucket. Participants in the process In November 1995, the board of directors of Dakota Coal authorized the execution of a field test and option agreement and a license agreement with the partnership of D.F. Schmidt, electrical/maintenance supervisor, and Bill Lengenfelder, president of Modern Industrial. The board also authorized entering into a dragline bucket field-testing agreement with the Falkirk Mining Co.

Jan 1, 1999

By Mark G. Lafontaine

Underground 802.11 wireless communications has become widely adopted for automation and communication purposes but maximizing the wireless signal presents many obstacles given the harsh environment as well as the presence of materials and conditions that can reduce signal propagation. Changes in elevations and curvatures in ramp to drift transitions also affect the wireless signal. Based on the requirements of wireless applications such as voice, data, or location tracking, the wireless site survey is the key tool for measuring and predicting signal strength and signal-to-noise ratio. These readings help determine the maximum distance between access points in order to sustain an overlapping wireless signal where required. This paper describes the methodology and tools used for measuring 802.11 wireless signal strength in an underground mine environment in Northern Ontario. The physical characteristics of the mine and the actual recorded wireless signal data will be presented in order for the audience to gain an understanding of the factors that affect signal throughput. Antenna selection used for the site survey will also be discussed as it played a key role in propagating the wireless signal.

May 1, 2013

By D. Harrington

Fine ventilation was discussed. much more 15 to 20 years ago than it is now, yet today there are tendencies in connection with ,-line ventilation (in fact, numerous ventilation systems have been installed in recent years) indicating that the lessons learned by bitter experience in the past either have been forgotten or lave not been brought to the attention of the present generation. Possibly, the mining min of today considers that conditions have changed so much that experiences of the past cannot be repeated today. At any rate, it seems desirable to restate some of the principles of mine ventilation that were understood more or less in the past and to call attention to some danger in connection with present-day trends or practices.

Jan 1, 1939

By Jonathan Taylor, Irwan Halim, Frederick (Rick) Vincent

The new underground facilities for the LINAC Coherent Light Source project at the Stanford Linear Accelerator Center in Menlo Park, CA, are constructed in very weak sedimentary rock interspersed with uncemented zones. In addition to several 21-footwide (excavated) tunnels, the NATM excavations include a large, 49-foot wide (excavated) cavern, an unprecedented size in this geology. The critical design issues include characterization of the weak rock, some shallow rock cover areas, and very stringent criteria for final invert slab movements within the tunnel. The design also incorporated severe seismic criteria, since the site is in close proximity to the San Andreas Fault.

Jan 1, 2007

By B. C. Christensen

The contract objectives are (1) to develop safe practice guidelines which will minimize the chance of fires in underground fueling areas and (2) to develop a low-cost, reliable, automatic fire protection system for underground fueling areas. The effort described by this report covers the period from 21 June 1976 to 30 September 1977 and accomplished the following tasks: ? Preparation of Data Plan and Data Acquisition, mainly through visits to sixteen mine sites and a literature survey. ? Analysis of the accumulated data, providing design inputs for (a) evaluation of the fire problem; (b) development of safe practice guidelines; and (c) development of recommended design concepts for automatic fire protection systems. ? Preparation of safe practice guidelines for underground fueling areas. ? Preparation of recommended design concepts for automatic fire protection systems for underground fueling areas. ? Design and fabrication of fire protection system for installation at Pine Creek Mine, Bishop, California. ? Install system and perform underground fire tests at Pine Creek Mine.

Jan 1, 1977

By Jerome F. Kuzmick

INTRODUCTION THE use of iron powder during the post-war conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: I. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price-The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1948

By Robert J. Timko

This U.S. Bureau of Mines study examined spontaneous heating episodes in coal mine pillars in an active underground coal mine. The information obtained from these incidents was then analyzed to learn which sampling methods provided the earliest indication of pillar heating. The objective of this study was to discover if the location of future events of pillar spontaneous heating could be inferred from the available information. The spontaneous heating-prone area in this evaluation involved pillars located just inby the mine portals. Several detection methods were used to determine gas levels outside as well as inside the affected pillars. It was hoped that, by incorporating external and internal sampling methods into an organized pro-gram, locations undergoing spontaneous heating could be determined more readily. This study found that by drilling small-diameter boreholes into the pillars, then obtaining gas samples from the affected pillars, the ability to locate early spontaneous heating episodes was improved. However, the ability to accurately predict future spontaneous heating events remains in question.

Jan 1, 2010

By Rafael C. Castro, Geoffrey Hughes, Fredrick (Rick) Vincent, Philip H. Albert

Seven pairs of drop and ventilation shafts, between two and nine feet in diameter, will convey combined sewer flow to a 230-foot-deep, 26-foot diameter storage tunnel. This paper will present case histories for each site. Discussion will include functional requirements, program and site access constraints, structural design, geology, the variety of excavation and lining construction methods used, and lessons learned. Noteworthy observations include the importance of assuring competent ground sup-port at the soil-bedrock interface and of achieving tight verticality tolerance using both top-down and raise bore excavation methods.

Jan 1, 2007

By S. Norman Kesten

The Galena mine is located astride the Polaris fault in the Coeur d'Alene district of northern Idaho. The surface installations are about a mile up Lake Gulch, the mouth of which is about 2.4 km (1 112 miles) west of the old town of Wallace. The mine had its beginnings when the first claims were located in the early boom days of the district in the 1880s and when the first underground ore bodies were opened up in 1917. During the ensuing 14 years, ore was mined from which were recovered 5.4 Mkg (12 million lb) of lead and almost 14.2 Mg (112 million oz) of silver. Workings consisted principally of a vertical shaft from surface to the 800 level and an offset underground shaft to the 1600 level, together with extensive lateral openings. High-grade silver-copper ore was discovered near the Silver Standard fault in the Sunshine mine, a few miles to the west, on the 1700 level in 1930. By 1937, the Sunshine and adjacent mines were producing silver-copper ore on a regular basis. In 1943 additional ore of a similar type was found along the Chester fault, to the east of the principal Sunshine workings. The interest of American Smelting and Refining Co. (renamed ASARCO in 1975) was aroused and the company's geologists determined that the Galena mine, idle since 1931, provided a geological environment in which similar ore might be found. After negotiations were initiated with the owners of the property, Callahan Zinc-Lead Co., the property in question was deeded to Callahan's wholly owned subsidiary, Vulcan Silver-Lead.

Jan 1, 1990

By J. R. Thoenen

In Progress Report 1,4/ a number of facto mere demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

The last issue included a discussion of recent indications of a 1983 recovery and a brief analysis of the contribution of the U.S. mining industry to the gross national product (GNP). In this issue we present sales and other data indicating the strength of the 1983 recovery and quantitatively analyze the structural shifts that have taken place in the U.S. economy and mining industry since 1972, and changes in electricity consumption by the mining industry. U.S. Economic Recovery The tentativeness in the February/March issue of Minerals and Materials regarding the strength and sustainability of the U.S. economic recovery can now be replaced with a note of increased confidence. Real growth of GNP on an annual basis in the first quarter of 1983 was 2.5 percent, compared with 1.4 percent predicted in the Economic Report of the President.1/ Preliminary second-quarter 1983 data provide further cause for optimism. Recently released data indicate that consumer spending is playing a key role in the recovery. Retail sales have increased significantly across a wide array of goods, especially consumer durables, where sales increased 4 percent from March to April (table J) and were 12 percent higher in April [ ] than the 1982 monthly average. Consumer durable sales were led by sales of building materials spurred by the growth in residential construction, motor vehicles and parts, and household durables, including appliances and furniture.

Jan 1, 1983

By Mohammed Z. Islam

As cities are growing all over the world, the need for urban transportation facilities are on the rise. Designers (of these facilities) today are faced with a number of constraints for their design, of the most is the space limitation and impact of new construction activities to the community. A typical subway station, as the focus of this paper, is approximately 600 to 1000 feet long, 50 feet wide and 2 to 3 story high. With such a large volume of construction activities, it is easily realized why underground stations are becoming obvious choice for larger cities eventhough the cost could be 2 1/2 to 3 times as much as an aerial station and 4 to 5 times that of an at-grade station [O'Neil et. al.(1977)]. Since cost is an important factor which is always increasing, therefore, the designer should have a good planning, consider alternatives for design and come up with a realistic design with minimum impact to the community. This paper is about the geotechnical considerations that the designer should be aware of. PLANNING A 1977 report [O'Neil et. al.(1977)] on the construction costs for a number of underground subway stations indicate that about 4 0% of the cost is site-controlled, 35% is structural items, and 25% is finish and equipment. It is seen that of opportunity exists for cost savings in the site selection and proper use of the site. Once the site is selected, the cost of construction become controlled by urban conditions at the site, geotechnical conditions, station size and depth. Therefore, the design-solution is very much site-specific. The geotecnical designer should collect the following information at the early phase of the design:

Jan 1, 1993

By J. P. Powell

The increased costs of exploration and drilling of new oil fields and the continued success of water flooding in nearly depleted oil fields have created a demand for information on the results obtained from individual projects. The Bureau of Mines has published several reports concerning water-flood activity in the Mid continent area and at the request of the industry has continued to collect and disseminate this information. This report was written in response to these requests. It describes in detail the water-flooding projects in Anderson, Franklin, Linn, and Miami Counties, Kans., and includes methods of water treating and the results obtained. The production histories of each county and many water-flood projects are shown graphically from the date of the first development. Maps of most of the major projects, showing their status as of January 1, 1953 are presented also. The practice of injecting water to stimulate oil production was legalized in Kansas in 1935, and the first water-flooding project authorized in this four-county area was initiated by the Texas Co. in December 1935 in Linn County, Forty-nine projects2/ initiated in the area to January 1953 are estimated to have recovered approximately 10 million barrels of oil that could not have been produced by methods used previously. About 7,900 productive acres had been, or are, flooded by these projects, and approximately 1.36 million barrels of water had been injected.

Jan 1, 1953

By D. Runnels, A. Allaire, J. Torrealba-Vargas

Data mining and modelling of operational data involves the discovery of patterns in large datasets for future use in benchmarking and plant optimization. The modern pattern of discovery in large data sets involves statistical techniques, machine learning and new visualization tools. Former examples of data mining are revisited and presented in this document. INTRODUCTION A network of enthusiastic and active professionals is currently developing and maintaining several open source statistical software tools (packages) for data analysis (example Rstudio, Orange, Spyder, etc.). The advantages of the open source software philosophy are the fast development and testing of the solutions presented to the community. Books and support are available for each software application. Since each modern work activity generates massive amounts of data, it is attractive to learn and test those available tools considering that we are at the door of the new work revolution coined as “Mine 4.0”. Data mining involves collecting large datasets, the preparation and cleaning of a dataset (term named data wrangling), the uploading of the data to a database program capable of handling big datasets, the development of prediction models and the presentation of the results. Machine learning techniques help to develop mathematical models and algorithms that could be used to improve the performance on a specific task. Mine operations are producing an incredible amount of data each day and the need to analyze those results seems to be impossible due to the lack of time, as well as the lack of skills to investigate the data collected. If we add to this the traditional habit of working in silos, an additional challenge is to consolidate databases from different departments in search of trends that could help to optimize production.

Jan 1, 2019

By Jack Bedder, Nils Backeberg

"Native antimony metal is rare and antimony generally occurs together with gold, lead, copper and silver. There are more than 100 antimony minerals, although the sulfide mineral stibnite is the main economic mineral.Antimony enters the supply chain either as a result of mining (primary production) or recycling (secondary production). China has by far the largest antimony resources and is, as a result, the world’s center for antimony mine production. While China remains the leading primary producer, accounting for 69 percent (80.5 kt or 88,700 st) of the global 117.5 kt (129,000 st) in 2017, market consolidation and regulatory inspections across China leading to closures of facilities have caused a significant decrease in Chinese output from 115.8 kt (127,600 st) in 2015 (81 percent of global production).Tajikistan and Russia are the next largest producers of antimony after China, both ramping up production in recent years. Russia could significantly increase its supply of antimony if Polyus moves ahead with supplying 10-12 kt/a (11,000–13,200 stpy) of contained antimony from gold tailings. Australia and Bolivia are also significant mine producers outside China. The value of the different ores varies based on the metal content of the concentrates, with the most valuable gold-bearing ores sourced from Australia’s Costerfield Mine and the least valuable mercury-bearing ores sourced from the Anzob Mine in Tajikistan. On average, Bolivian and Russian ores trade at an intermediate value between those from Costerfield and Anzob. Nearly all of the rest-of-world production is exported to China, where the ores and concentrates are processed into antimony ingots and oxides.Antimony ingot production is not as widespread as is the case with antimony mine production, owing to the high levels of pollution that are associated with antimony smelting. It is for this reason that smelting has been largely confined to China and other Asian countries ,such as Vietnam and Myanmar, where environmental legislation has historically been less stringent. Tajikistan has become a growing producer of antimony ingot since 2014, coming from the commissioned metallurgical plant at the Anzob Mine.Antimony oxide production is undertaken on four continents with China being the biggest producer. There is also a considerable amount of oxide production in Europe (mainly Belgium and France), which relies on imported antimony metal feedstock, mostly from China.A new antimony project under construction by Strategic and Precious Metals Processing (SPMP) in Oman made progress in 2016 and 2017, and after producing first metal in April 2016 in test facilities, was set to be commissioned in the first quarter of 2018. Commissioning had been moved back to June 2018, with a potential ramp-up to 2-3 kt/a (2,200 to 3,300 stpy) of antimony metal by the end of 2018. SPMP is also reviewing producing antimony oxide as part of its flow sheet."

Jan 7, 2018

By John J. Ginty

The objective of the work reported herein was to evaluate state-of-the-art repeaters used in wireless communications to determine their suitability for use in extending the range of portable and mobile communications in underground mine applications. The scope of the work included wireless repeaters in the frequency range from LF (500 kilohertz) up to the one giga-hertz range. These repeaters included not only single-channel repeaters, that is F1/F1 repeaters for short range simplex party line communications, but in addition, F1/F2 type repeaters currently commercially available in the HF, VHF and UHF bands.

Jan 1, 1975

By P. Tolvanen, A. Jalili

"When hard times strike in the mining cycle, sites tighten their belts and focus on lowering their unit costs. Lower unit costs can be achieved by reducing expenditure, increasing production, or by a combination of both. Faced with these requirements, site personnel must turn to areas where they can focus their effort for maximum return. For many sites, both in Canada and overseas, focusing on improving flotation cell maintenance is one of the areas where gains can be made for minimum outlay. Due to resource limitations and/or lack of equipment understanding, maintenance on many sites is only conducted on a reactive basis, once equipment fails. This paper will promote the idea that mineral processors should become more familiar with their equipment so they can ensure that the plant’s ability to produce is not compromised. By better understanding the flotation equipment and ensuring the critical components are maintained, it should be possible to unlock value in an operation. Flotation equipment inspections will be discussed in detail, including key items to look for during these inspections. Potential approaches for predicting wear and change-out time for flotation equipment components will be also demonstrated. An example of one approach used at a South African nickel site will be given.INTRODUCTIONWith metal prices decreasing and operating costs rising, concentrator operators are looking for ways to improve their bottom line. Lower unit costs can be achieved by reducing expenditure, increasing production, or by a combination of both. To meet the expectation of shareholders, mineral processors must turn to areas where they can get the best return for their efforts. One area where there is a large opportunity for improvement is in the maintenance of flotation equipment.On many mine sites, both domestically and around the world, it is quite common to see the philosophy applied of repairing equipment only once it has failed. Though some sites have advanced enterprise management systems and monitoring programs, in the authors’ experience, the decision on flotation equipment maintenance is rarely made on a proactive basis. Two common trends that are evident in the mining industry are that operations are under pressure to keep the plant producing, and maintenance managers generally have very strict budget targets to meet. In addition to these factors, few sites have a good understanding of the financial implications of running with worn or broken flotation equipment. Knights, Jullian and Jofre (2006) summarize this situation well, stating that the lack of correlation between some commonly used maintenance performance measures and key business drivers can lead to maintenance being seen only as a cost center (that needs to be reduced) rather than a tool for productivity improvement."

Jan 1, 2015