Search Documents

By M. Hooman, W. M. Marx, R. C. W. Webber-Youngman

This paper discusses a study that investigated different underground bulk air heat exchanger (>100 m3/s) design criteria. A literature review found that no single document exists covering all design criteria for different heat exchangers, and therefore the need was identified to generate a guideline with decision analyser steps to arrive at a technical specification. The study investigated the factors influencing heat exchanger designs (spray chambers, towers, and indirect-contact heat exchangers) and the technical requirements for each. The decision analysers can be used to generate optimized, user-friendly fit-for-purpose designs for bulk air heat exchangers (air cooler and heat rejection). The study was tested against a constructed air cooler and heat rejection unit at a copper mine1. It was concluded that the decision analysers were used successfully. This tool (decision analysers) can be used by engineers for the efficient and cost-effectively design of heat exchangers.

Jan 1, 2015

U.S. Minerals Coordinating Council Advised. -The Critical Materials Act of 1981, H. R. 4281, introduced on July 27, would create a Council on Critical Materials in the White House Executive Office to oversee Federal materials programs involving $1 billion committed to research by 14 agencies, and to serve as the President's focal point to evaluate materials policy. It was introduced by Congressman Fuqua (D-Fla.) whose Committee on Science and Technology has over-sight over the implementation of P. L. 96-479, the National Materials and Minerals Policy, Research and Development Act of 1980. Bulgaria's Mineral Bank. -Recently Bulgaria established a mineral bank to facilitate receipt of foreign credits for exploiting Bulgaria's mineral raw materials. The bank has wide powers to enter into business arrangements with foreign creditors. Bulgaria's main interest in trading with the West is to import the technology for developing energy and mineral resources.

Jan 1, 1981

By Michael J. Robison, Wojciech F. Klecan, Robert L. Horner

Since 1928, nearly 64 km (40 mi) of tunnel have been excavated within the relatively soft Cooper Group, more commonly known as the “Cooper Marl,” for water supply and transporting wastewater in the Charleston area. The majority of these tunnels are unlined and still in operation, while others collapsed shortly after excavating. Tunnel behavior and support requirements vary considerably in this material due to differences in geotechnical properties. The 4.8 km (3 mi) long, 2.4 m (8 ft) diameter Bushy Park Water Tunnel, completed in 1997 for Charleston’s Commissioners of Public Works(CPW), required no ground support. By comparison, the 1.6 km (1 mi) long, 2.4 m (8 ft)diameter Harbor Wastewater Replacement Tunnel now under construction needs continuous support close to the advancing face, despite being located in the same geological formation. Case histories and general guidelines for designing tunnels in the Cooper Marl are presented.

Jan 1, 2001

By K Thorpe

Amorphous silica deposits have been identified at Tikitere and Taheke near Rotorua. Two areas at Tikitere have been surface sampled and drilled to establish a resource of amorphous silica in excess of one million tonnes. A pilot plant was established to develop a process to manufacture a high quality super pozzolanic material. This development process took two years before a commercial product was introduced to the construction industry in 1996. The amorphous silica product, marketed as Microsilica 600, is used as a pozzolanic material to produce high quality strong and durable concrete, sprayed tunnel linings, mortars and grouts. Microsilica 600 has been used locally and exported to 11 countries.

Jan 1, 1999

By Marco Lombard, Paulus Kapolo, Christopher J. Greet

"The conversion of a concentrator from one grinding media type to another is a major undertaking in terms of both financial and technical risk. So, a strategy of completing sufficient laboratory and field tests to mitigate this risk, and give the operation confidence that advancing to plant trial will give a high probability for success.The objectives of this paper are twofold: to provide the reader with a strategy for mitigating risk prior to undertaking a plant trial; and to provide a statistical basis for analysing plant trial data. That is, when employing an electrochemically inert grinding media in the primary grinding circuit it is possible to change the pulp chemistry of the system and improve the metallurgical response of the ore.This paper tracks the changes in pulp chemistry and metallurgical performance of Rosh Pinah Zinc Corporation’s silver/lead/zinc concentrator as the primary ball mill was converted from forged steel grinding media to high chrome grinding media. The changed in metallurgical performance are correlated to the shift in pulp chemistry.INTRODUCTIONTheoryBruckard et al (2011) recently published an article describe the effect of the grinding environment on the flotation of copper sulphides. While this paper confined its discussion to copper sulphides the arguments presented apply equally to other sulphide mineral systems. Broadly, these studies indicate that most sulphide minerals are more noble than the grinding media used during comminution. Therefore, the sulphide minerals are cathodic with respect to the forged steel grinding media, and the following reactions apply:Cathode (sulphide mineral): ½O2 + H2O + 2e- ? 2OH- (1)Anode (grinding media): Fe ? Fe2+ + 2e- (2)A galvanic couple between the grinding media and the sulphide mineral(s) exists, which increases the corrosion rate of the forged steel media. The corrosion products of the grinding media, iron oxy-hydroxide species, invariably precipitate on to the surfaces of the sulphide minerals thereby affecting their floatability (Johnson, 2002).The application of more electrochemically inert grinding media to “real” ore systems at an industrial level to improve metallurgical performance has not gained universal acceptance. The aim of this paper is to provide a protocol for conducting laboratory and plant test work that clearly demonstrate that metallurgical benefits are not only possible, but measureable, by way of example. In this case, the work conducted at Rosh Pinah Zinc Corporation in Namibia is described."

Jan 1, 2013

By R. C. Bryce

"Selbaie is located northwest of Joutel, in what is known as the fourth east-west volcanic sediment group in northwestern Quebec. The main metals produced are copper and zinc, with important contents of both silver and gold. Production comes from an open pit mine on the A-I zone and from two underground mines on the B zone and the A-2 zone. Each mine gave rise to important capital investment programs for construction and mine development, all of which were managed and staffed with company-hired, non-union personnel. Production from all sources now exceeds 7000 tonnes per day, with a workforce of540 regular employees. Of particular interest technically is the high recovery of B zone reserves underneath 40 m of overburden cover, the low-cost capital development of the A-2 zone, the computerized control of open pit mining, and the successful copper-zinc separation of the A-1 zone ore. Due to the low grades of the mineral deposits, efficiency in all aspects of the production process, is essential to the success of the operation.LocationThe Selbaie Mine is located 82 km northwest of the locality of Joutel in northwestern Quebec (Fig. 1). Access to the mine is by an all-weather road, 32 km of which is paved. A second road access to the site is via La Sarre, 134km to the southwest. Employee access, materials transport and haulage of copper and zinc concentrates take place over both of these roads."

Jan 1, 1990

By C. F. Strydom

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The Self-directed work team concept is the product of relentless performance pressure on American industries during the late eighties and early nineties from other world industrial leaders like Japan. The concept proved to be a successful vehicle by which the Americans could increase their production and improve their safety statistics. The aim of this study is to evaluate the concept as a means to improve the overall performance on South African goldmines. he study is directed by a historical research section, answering questions like: ?Why do we need to change? ?What is a Self-directed work team? ?What are the principle advantages of the concept? ?What are the essential requirements for the concept to succeed? The study also includes an empirical research section that focuses on the current Self-directed work team situation in the South African gold mining industry. The empirical research section is limited to three case studies within Anglogold due to a study period of only six weeks. The mines chosen for the case studies have been labelled Mine 1, Mine 2 and Mine 3. The latter being the base mine allowing for a more in depth study. This includes a perception analysis towards Self-directed work teams within the mine. The study proves the truth of the Latin proverb ?Tempora mutantur, nos et mutamur in illis? meaning ?The times are changing, and we are changing with them?. The chief change catalysts identified are a dwindling gold price and a projected labour crisis. From the study it is evident that the Self-directed work team concept disposes of the critical parameters required for a dramatic improvement in performance. The study also indicates that for the concept to succeed, certain factors like top-level commitment and management-employee trust have to be in place. Sadly, the concluding part of the study proves that very few of the identified critical success parameters are present in the South African gold mining industry. This can serve to explain why the industry only has success with the concept when monetary gain is the chief motivator. The study only focuses on the reasons why the concept is not performing to its full potential and does not wander into explaining the reasons for the current unsupportive milieu in the industry. Self-directed work teams could well rescue the South Africangold mining industry but currently we are driving a square pin into a round hole! [Terminology SDWT?Self-directed work teams AEL?Adventure Experiential Learning ISW?In-stope worker POLC?Plan, organize, lead and control TEC?Total employee costed Silo?The confinement of departments preventing networking JCI?Johannesburg Consolidated Investment Co. Ltd]

Jan 1, 2002

Mineral liberation data are routinely obtained for a wide variety of applications, including ore characterization and characterization of various metallurgical test products obtained in bench-scale laboratory testwork. Newmont Mining Corporation owns several properties in the Carlin Trend containing refractory gold ores. These ores are generally difficult to treat and have to undergo several processing stages for gold recovery. At Carlin?s Mill 5 operation, flotation is used to pre-concentrate some of these difficult ores to produce a sulfide concentrate to feed the roaster. It is of interest from a flotation perspective to be able to study the floatability of pyrite, arsenopyrite and arsenian pyrite, since these minerals all have different quantities of gold associated with them, and have to be recovered to ensure a successful separation has been achieved. In this paper, a detailed MLA study on several Carlin ores was undertaken on samples from flotation tests, using air or nitrogen as flotation gas, specifically to study the differences in floatability characteristics, which ultimately impacts overall gold recovery. I

Jan 1, 2009

By Eleanor Abshire

[THE INCREASING use of hafnium as a vital component in atomic power reactors has brought this metal into recent prominence. A literature survey was made and this bibliography was compiled to provide research and production groups with a ready source of reference to this important metal anti its compounds. This service is rendered by the Zirconium Information Center, which is sponsored by the Department of the Navy, Bureau of Ships, and the F .S. Department of the Interior, Bureau of Mines, tit the Bureau's Northwest Electrodevelopment Experiment Station, Albany, Oreg. The following reference sources have been reviewed for this compilation : Chemical Abstracts; Industrial Arts Index; Crerar Metals Abstracts; Nuclear Sciences Abstracts; Bureau of Mine; Information Cicular 7771, Bibliography of Zirconium; anal Bureau of Mint' Information Circular 7830, Bibliography of Zirconium, suppllement to Information Circular 7771.]

Jan 1, 1960

A survey has been undertaken of the petrography of North Island greywackes with a particular focus on the occurrence in them of smectite (swelling clay) and chlorite, two minerals that are closely associated, chemically similar, and commonly interlayered with each other. Smectite is the mineral which is a major cause of greywacke aggregatesÆ poor performance. Smectite occurs in post-metamorphic shear zones and in surface weathering profiles over greywackes. This study focuses on the petrography of fresh greywacke rocks.   The occurrence and abundance of smectite and chlorite and their relationship in greywackes is largely a function of the chemistry of the sediment and the maximum temperature that the sediment has been subjected to during diagenesis and/or very low grade (anchizone) metamorphism. Rock chemistry, particularly total iron and MgO, determines the smectite and/or chlorite content in fine-grained greywackes (argillites and siltstones) but chemistry is less influential in sandstones, where at low grades of metamorphism much of the Fe and Mg of the rock is held in unreacted detrital minerals and the mineral constituents of lithic grains.   Four zones which represent different levels of diagenesis and very low grade metamorphism, based on the crystallinity of illite and chlorite in the greywackes, and the proportion of smectite interlayered with chlorite, have been mapped in the North Island. In the anchizone smectite does not appear as a discrete mineral, it is always interlayered with chlorite. In the upper anchizone chlorite contains approximately ten per cent of smectite interlayered with chlorite. In the lower anchizone about 30 per cent smectite can occur in chlorite.   In addition to the smectite and chlorite inherent in the greywackes as the result of the thermal overprint, smectite as a discrete mineral and smectite-chlorite interlayered minerals with high levels of smectite, occur in abundance on shear zone surfaces and in alteration zones adjacent to shear zones; these are the main contributers to the high levels of smectite recorded in many greywacke aggregates.

Jan 1, 2006

By Thomas C. Wilder

Jan 1, 1965

By Madan M. Singh

This report presents the results of an investigation of inclined roof bolts, anchored over pillars, in room-and-pillar coal mines susceptible to shear failures of the roof. Although the field data do not support this contention, it is believed on the basis of analyses and other work that inclined roof bolts do offer potential under some circumstances.

Jan 1, 1978

By Annie G. Smelley

As a part of research conducted in its mission to effect pollution abatement, the Bureau of Mines, U.S. Department of the Interior, is developing a dewatering technique that allows for disposal of clay wastes, for reuse of water now lost with clays, and for reclamation of mined land. The technique utilizes a high-molecular-weight nonionic polyethylene oxide polymer (PEO) that has the ability to flocculate and dewater materials containing clay wastes. In laboratory experiments, coal-clay waste, potash-clay brine slurry, phosphatic clay waste, uranium tailings, and talc tailings were successfully consolidated. Coal-clay was te was consolidated from 3-. 6 to 57 percent; potash-clay brine slurry was consolidated from 3.8 to 35 percent; phosphatic clay waste from 15.6 to 49 percent; uranium tailings from 15.4 to 67 percent; tailings from talc production from 9.7 to 53 percent; and an acidic Ti02 slurr slurry from 1.68 to 30 percent.

Jan 1, 1980

By A. W. Diedericks

Rosh Pinah Zinc Corporation (RPZC) identified implementing a Mineral Resource Management (MRM) programme at the mine as a strategic incentive. The purpose of the programme is to optimize the economic value of the RPZC mineral resource, over the total value chain of the mine, taking expected macro economic conditions into consideration as well. With Mineral Resource Management still being a relatively young drive in the mining industry, information on the concept is relatively scarce. RPZC had several successes and problems with implementing such a concept and also still has a way to go before a complete Minerals Resource Management approach is implemented at the mine and entrenched as a working culture. The purpose of this paper is to: ?define a systems approach to implementing a Mineral Resource Management programme at a base metal mine ?indicate the specific MRM approaches taken at RPZC ?indicate the expected advantages of implementing a MRM approach ?measure the actions already taken against the systematic MRM approach, and indicate the advantages already captured ?indicate the way forward taking lessons learned into consideration ?indicate proposals to implement the MRM approach in the macro mining environment in South Africa.

Jan 1, 2003

Recently, work was carried out by the Shotcrete Working Group to study anisotropy in steel fibre reinforced shotcrete using strain-controlled, compressive strength testing methods. The shotcrete materials used and specimen preparation procedures as well as testing methods are described. The test results are discussed and it is concluded that, because of the anisotropic nature of fibre reinforced shotcrete, it may be worthwhile investigating the degree of such anisotropy in practice using strain-controlled, strength testing techniques.

Jan 1, 2001

By L. Adler

Longwall caving, one of the most economical and attractive mining methods, is yet one of the most difficult and hazardous.1 This dualism is inherent in a method which manipulates the mine supports themselves to aid in excavation. The difficulty is further compounded by the lack of an analytical method to predict and control results. This paper is intended to meet this need by providing a first approximation to the mechanics involved. The analysis will be limited to materials which are linear-elastic, homogeneous and isotropic. The rock structure is assumed to consist of beds of uniform thickness with no interbed bonding.2 Consequently, the mine roof can be likened to a beam, in which the action characteristic of longwall caving is the controlled deflection of the barrier supports. This deflection causes load to be intentionally transferred from these barrier props to the working face.3 Two of the requirements of this method, shared in common with other mining methods, are the provision of (1) adequate and (2) safe working space. The third requirement is the one characteristic of longwall caving and is somewhat in conflict with the second; (3) the development of near-failure static loads at the face. Requirement (1) is handled by spacing the barrier props sufficiently far from the working face for efficient operation. Requirement (2) limits the static stresses in the structure to predetermined allowable values. This means that it is not desirable to induce a maximum load on the working face as requirement (3) may imply. Such a condition could produce collapse in the whole structure. It is the purpose of the undercut to limit the depth, and thereby control the failure of the face. Therefore, requirement (3) really means the development of an optimum, not maximum, load which, in conjunction with undercutting, produces failure at the working face, with minimum powder consumption. Stress analysis requires an exact delineation of the structure and loads. The structure will be defined as the immediate roof and its supports. Since the roof is severed at the caving line, the supports reduce to the barrier props and the working face, as shown in Fig. 1. The mechanics of failure within the working face itself are complex and beyond the scope of this study, since the face represents a typical mine invert structure.4 However, this lack can be made good by the judicious collection of field data. The primary load on the structure is its own weight or body load which can be considered uniformly distributed over its upper surface. Additional loading occurs due to interference of overbeds with the structure. Wherever this occurs, the effect can be approximated by a load uniformly distributed on the upper surface of the structure.5 When this interference is intermittent, as with a much thicker overbed, the elastic curve for the overbed is superimposed on that for the structure and the extent of interference noted, as Fig. 2 shows. However, for simplicity, this study will ignore such intermittent loads without impairing the generality of approach. Consequently, the free-body diagram is that of a uniformly loaded cantilever beam with an inter-mediate support, as shown in Fig. 3. For convenience of analysis, the diagram will be divided just to the

Jan 1, 1961

By Ellsworth R. Spencer

An assessment of U.S. western hardrock miners? noise exposures was conducted as part of a multi-year National Institute for Occupational Safety and Health (NIOSH) survey of noise exposures in each sector of the mining industry. Noise from selected mining equipment and operator noise exposures were measured, analyzed and tabulated for dissemination to the participating sites and are being used to direct NIOSH research and interventions to address the greatest noise hazards. Eighty-two noise dosimeter measurements were obtained, along with time-motion studies as the miners operated hardrock mining machines. Of the operators, 96% had daily noise doses that exceeded the U.S. Mine Safety and Health Administration?s (MSHA) permissible exposure level. The average gold miner dosages while operating the following equipment were: haul trucks - 261%, load-haul-dumps (LHDs) - 235%, single boom drills - 221%, bolters - 214% and dual boom drills - 163%. The worst exposure level was a silver miner with a daily dose of 873%. Time-motion data showed that this miner?s exposure accumulated most rapidly while operating a jackleg drill. These results will be used to help prioritize noise control development by NIOSH and other partners.

Jan 3, 2010

By Ralph P. Hackl

Ore at the Congress gold property, located near Goldbridge, British Columbia, is extremely refractory with most of the gold disseminated in fine-grained arsenopyrite. Metallurgical testwork conducted by Giant Bay Biotech Inc. indicated that biooxidation pretreatment was capable of increasing cyanide gold recovery from the ore to greater than 90%. To determine if the bioleach process could be successfully scaled up, a 225m' (7950-cu ft) commercial size bioleach reactor was built and tested at the mine site in 1989. At that time, the tank was the largest bioleach reactor ever operated. The objectives of the program were: • to ascertain if the biooxidation rates obtained in lab and pilot-scale reactors could be duplicated in a commercial scale tank; • to identify agitation conditions under which the process will function optimally; and • to demonstrate the bioleach process on a scale sufficient to satisfy the owners and potential investors.

Jan 1, 1990

By T. H. Jeffers

The U.S. Bureau of Mines has developed porous beads containing immobilized biological materials for removing metal contaminants from waste waters. The beads, designated as BID-FIX beads, are prepared by blending biomass, such as sphagnum peat moss or algae, into a polymer solution and spraying the mixture into water. Laboratory studies were conducted to determine bead sorption and elution characteristics. Batch and continuous tests demonstrated that BIO-FIX beads sorbed arsenic, cadmium, lead, and other toxic metals from acid mine drainage waters collected from several sites. Selectivity for heavy and toxic metal ions over calcium and magnesium was demonstrated. The beads exhibited excellent metal sorption and handling characteristics in stirred tanks, column contactors, and a low-maintenance passive system. The sorption process was reversible, and metal ions were eluted from the beads using dilute mineral acids. Cyclic tests indicated that the beads continued to extract metal ions after repeated loading-elution cycles.

Jan 1, 1991

By J. R. Ross

A reconnaissance for sources of scandium and a metallurgical investigation of recovery methods for byproduct scandium from uranium mill solutions were conducted by the Bureau of Mines. The work on scandium was undertaken to obtain information on domestic resources and to explore and develop recovery procedures in consonance with the Bureau's long-range program for conservation and wise utilization of mineral resources. The element scandium is widely distributed in the earth's crust in trace amounts, but it seldom occurs as an important constituent in any mineral. An exception is thortveitite, (Sc,Y)2 Si207) a rare mineral that contains various amounts of scandium and yttrium and may contain up to 42 percent scandium oxide (SC203). Knowledge of the chemistry of scandium has expanded rapidly in recent years (1, 4, 9)4 but only fragmentary information is available about the metal because it is still largely a laboratory curiosity without established uses (2, 3). A recent study shows some of the physical proper-ties of the metal are (1) density of 3.05 grams per cubic centimeter) (2) melting point of 1,540° C, (3) hexagonal close-packed structure) (4) hardness of about 50 Brinell (500-kilogram load), and (5) an alloy behavior similar to yttrium and rare-earth metals (2). The price of $2,850 a pound for scandium oxide of 99.9 percent purity and $2,700 a pound for oxide of 99 percent purity reflects the scarcity and complex chemistry of the element.

Jan 1, 1962