Search Documents

By Yousef Ghorbani, Jafar Abdolahi Sharif, Fatemeh Kazemi, Ataallah Bahrami

Kinetic models are the most important tool for predicting and evaluating the performance of flotation circuits. Gilsonite is a natural fossil resource similar to an oil asphalt, high in asphaltenes. Here, in order to determine the kinetic order and flotation rate of a gilsonite sample, flotation experiments were carried out in both rougher and cleaner stages. Experiments were conducted using the combinations of oil–MIBC and gas oil–pine oil, with one test without collector and frother. Five kinetic models were applied to the data obtained from the flotation tests using MATLAB software. Statistical analysis showed that the results of the experiment with oil–MIBC were highly in compliance with all models. Kinetic constants (k) were calculated as 0.1548 (s−1 ) and 0.0450 (s−1 ) for rougher and cleaner stages, respectively. Rougher and cleaner tests without collector and frother also matched all models well (R2 > 0.98), with k values of 0.2163 (s−1 ) and 0.284 (s−1 ), respectively. The relationship between flotation rate constant, maximum combustible recovery, and particle size showed that the maximum flotation combustible recovery and flotation rate were obtained in the size range of −250 + 106 μm in the rougher and cleaner stages. The combustible recovery and flotation rate were higher in the rougher flotation process than in the cleaner stage.

A commonplace, sometimes overlooked or taken for granted, article of everyday existence is the tin can. Produced from thin gauge low carbon steel, and commonly coated with a mere 60 millionths of an inch of pure tin, the product is however strong and corrosion resistant. Tin-plate serves a myriad of purposes-the most important being to meet the requirements of the canning industry. Australia's newest steel product, tin-plate, was first produced on a commercial scale during the early part of August, 1957. The commissioning of the Hot Dip Tinning Plant (Fig. 1) of The Broken Hill Proprietary Co. Ltd. at Port Kembla, marked the culmination of a proposal dating back to 1939, the advent of World War II having caused its deferment to the present time.Cornish tin is known to have been exported as early as 300 B.C. to Syria and tinned vessels existed even in the year A.D. 23. The tin coating of plate could be described as an ancient art, believed to have had its origin in Bohemia in the thirteenth century. During the next 450 years, the process spread through Saxony to Pontypool in Monmouthshire, but it was a further half century before any measure of success was obtained.Perhaps the two greatest milestones in tin-plate manufacture were the rolling of iron plates first carried out in 1728, thereby outmoding the hammer formed sheet, and more recently, the development of the electro-deposition process. By the nineteenth century, several important changes had arisen; namely, the substitution of steam for water power, coke for charcoal in the production of the base metal, and...

Jan 1, 1958

By Jack S. Greber

The mining industry generates an estimated 2.3 billion tons of solid waste each year and the total accumulated mineral resource solid waste at both active and inactive mine sites, approaches 30 billion tons. Five industries generate 85 percent of mine solid waste: copper, phosphate, iron, uranium, and coal. Over the past several years, the Federal government has shown increasing interest in the proper disposal of solid wastes generated by the mining industry. Three new pieces of federal legislation have been passed recently beginning with the most comprehensive regulatory authorization passed in 1976, the Resource Conservation and Recovery Act (RCRA) which has been amended to the Solid Waste Disposal Act Amendments of 1980. RCRA is implemented and enforced by the Environmental Protection Agency (EPA) and intended to control municipal and industrial solid wastes. Next came the passage of the Surface Mining Control and Reclamation Act (SMCRA) of 1977 which is implemented and enforced by the Department of Interior to control coal surface mining and the surface effects of underground coal mining, and finally, the recent Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978 implemented by EPA and enforced by the Nuclear Regulatory Commission (NRC) to control uranium mill tailings disposal.

Jan 1, 1981

(Published by courtesy of the Great Boulder Pty. Gold Mines, Limited)1. INTRODUCTIONThe faults described in the following paper are of a somewhat unusual character, and have presented a serious problem both in the development and mining of many ore-bodies on the Eastern side of the Boulder Belt. They are mentioned only briefly in the literature of the field, but were observed by, both Stillwell (1)t and Gustafson (2), and have been studied by other geologists and operators in various parts of the "Belt." Their effect on the lodes of Hamilton Section, Great Boulder Mine, was described by King (3) in 1937, and, during recent years, they have been encountered in most of the Great Boulder workings extending east of the Boulder Dyke.Although this paper is based mainly on a study of faulting and development problems on the Great Boulder mine, the general conclusions reached may be applicable to the solution of similar faulting problems in other mines throughout the field.In order to arrive at a clear understanding of the somewhat complicated relationships which the east-dipping faults bear to the lode systems it will be necessary to give a brief outline of the salient geological and structural features of the "Belt" before proceeding to describe the faults themselves.2. GENERAL GEOLOGYThe most recent descriptions of the geology of Kalgoorlie are those by Stillwell (1) and Gustafson (2) and the reader is referred to these as representing the basis of current knowledge of the geology of the field.The Boulder Belt is comprised of a central core of altered quartz dolerite which is flanked on either side by fine grained greenstones and lavas, usually referred to as the calc schists. Down the centre of the quartz dolerite mass there is an infolded bed of slate (2, p. 105) which has been intruded in lit par lit fashion by albite porphyry; the composite body of slate and porphyry so formed is known as the "Boulder Dyke." Numerous smaller porphyry dykes intrude both the quartz dolerite and the calc schist; these vary in composition and range from chloritised hornblende porphyrites to albite porphyries.The whole of the rock assemblage has been subjected tG a considerable amount of folding, faulting, shearing and fracturing, the greater part of which took place before the formation of the lodes.

Jan 1, 1941

The phenomena of nature cannot present themselves to any thinking wild without claiming from it some solution. The earth, as it has often been observed, is laid out like a well ordered cabinet, presenting to us, in measure, some means of judging how the laws of nature and the essential properties of matter have worked out all we see before us. "That there have been depositions of strata gradually laid down aud stocked with the remains of the living objects, vegetable and animal, that flourished when they were being imposed, is an universally acknowledged fact. It speaks of a constantly maintained series of operations whereby the globe has been brought to its present condition, and which are ever advancing it to stages that are still before it. That immeasurable ages have been consumed in effecting these developments is also conceded. We witness the very graduated rate of the existing advances and can see that the past action must have been conducted in the same slow deliberate manner. There are many questions, however, upon which inquirers are not agreed, hence they are still within the domains of fair discussion.What has led to those great climatic changes whereby the same portions of the earth have had at various times climates that were glacial, temperate, and tropical? What causes the constant contortions and dislocations of strata and the upheaval and depression of land levels, and that there is a tendency to alternation in the parallel areas undergoing opposite kinds of movement as if the sinking of one area balanced the rIsing of another? What is the reason that the centres of volcanic action are continually shifting, and that the line of greatest activity is always upon the rising areas? That portions of the earth have been subjected to intense alid long continued volcanic action, and again to long periods of repose, and that the periods of activity and repose are·recurrent at long intervals of time? What the mountain chains of the world are in broadly parallel bands? What has caused the stratified rocks to be tilted from their original?

By Y. I. Yang, Y. -B. Tang, D. -J. Ma

Chlorine-containing minerals are commonly present in coal. Associated minerals such as pyrite can undergo exothermic reactions. Consequently, it is of great significance to study the effect of inorganic chloride on the spontaneous combustion of coal. In this study, the effects of five inorganic chlorides (sodium chloride, magnesium chloride, potassium chloride, calcium chloride, and zinc chloride) on the spontaneous oxidation of coal were investigated. Analysis of the gaseous products of coal oxidization at low temperatures (323K to 453K) showed that the presence of inorganic chlorine in coal markedly decreases O2 consumption and the generation of CO and CO2. Samples of raw coal and chlorine-loaded coal were oxidized for 36 hours under the same experimental conditions. Infrared diffuse reflectance spectroscopy results showed that inorganic chloride can inhibit the oxidative decomposition of some functional structure components (methyl, methylene, methine, and hydroxy) in the coal. The influence of inorganic chloride on the oxidation characteristics of the functional groups in coal during spontaneous combustion was investigated using benzyl alcohol and 1-phenylpropanol as model compounds, which were tested under the same experimental conditions as the coal samples. The oxygen consumption of model compounds with and without the addition of inorganic chloride further suggested that inorganic chloride may hinder the oxygenolysis of these structures during low-temperature oxidation. This phenomenon can be attributed to the radical reaction from the perspective of radical chemistry. It can therefore be concluded that inorganic chlorides play an inhibitory role in the spontaneous combustion of coal.

Jan 1, 2015

INTRODUCTION ò World coal production, Exporters and Importers òNew Zealand Exports, Markets and Products ò Types of Markets and Price Setting ò Bench Mark Prices and Exchange Rate ò Transport ò International Marketing - Key Factors ò Coal New Zealand , the Challenges

Jan 1, 1996

By R. Heuberger

South Africa?s Mining Industry operates in an uncertain world. The industry is buffeted by problems regarding retrenchments, unemployment, low productivity, rising costs, volatile exchange rates, commodity prices and government regulations. With these uncertainties facing the decision makers, what does applied technology offer the industry?s management? Modelling languages with risk analysis have been available for decades, but in the past their use has been very expensive, requiring large mainframe computers and lots of computer time. Today, PCs and laptops have incredible power, which makes interactive risk analysis affordable and viable for all enterprises, whether small or large. ?What is risk analysis? ?What is Monte Carlo simulation? ?What kinds of computer models need to be created to use risk analysis and Monte Carlo simulation effectively? This paper addresses these questions and illustrates, with a practical example in the mining industry, how risk analysis techniques can be used to support decisions in the climate of uncertainty.

Jan 1, 2005

By J. A. L. Napier

It has been established that significant time-dependent stope convergence may occur over time periods of hours and days in certain hard-rock gold and platinum mines. The source of this time-dependent behaviour appears to be associated with both pre-existing discontinuities and with mining-induced fractures that form near the stope face. These induced fractures may be associated with blasting processes and may also be formed in response to high stress concentrations in the unmined regions immediately ahead of the stope face. In shallower platinum mining operations, time-dependent behaviour is, however, observed to be much less marked unless some form of specific mining-induced fracturing occurs. One particular case of considerable interest is the time-dependent behaviour that is found to be associated with the formation and deployment of crush pillars. The purpose of the paper is to present a simple limit-equilibrium computational model of this behaviour that is sensitive to both the formation sequence and the size of planned crush pillars in a mine layout. This model provides a useful means to optimize the sizing of crush pillars, and at the same time may be used to identify potentially hazardous circumstances in which pillars may not crush in a stable manner.

Jan 1, 2012

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillars is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to pre-failure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25 to 40 percent higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Pre-failure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to improved designs as mines become deeper.

Jan 1, 2001

By Pound J. R

THIS mine, which is the property of the S. and M. Syndicate, London, is located at Moina, in North-West Tasmania, 18 miles from Stavertorr railway station and 36 miles from Devonport. There are metalled roads from both of these places, and, althoughhilly, these are good for team or motor traffic. Mails and passengers are provided for by a tri-weekly coach service from Sheffield, a railway town, distant 23 miles. The Moina mining field is situated on a main spur between the Forth and Iris Rivers, andat an elevation ranging from about 500 ft. above sea-level at the Forth River to 2400 ft. at the All Nations mine. The elevation at the mine office of the S. and M. mine is 1900 ft. The average annual rainfall, as recorded for the past eight years, is. 68 in.This inclildes, however, a couple of years during which the rainfall was much above normal, and taken over a longer period 60 in. would be nearer the average.

Jan 1, 1919

The analysis of in-mine grounding systems began with an extensive literature search which is still in progress. About a dozen articles have been found which deal directly with grounding problems on low voltage power systems or mine power systems. These systems have special grounding problems because normal load currents can be nearly as large as many types of fault currents. Information has been collected on the influence of cable spacing) conduit geometry, location of nearby conducting structures, etc., on the magnitude and path of fault current. Many other articles have been found which are less directly related to mine ground system analysis. The in-mine ground system analysis team has also inspected portions of two mine power systems to become familiar with the practices used in grounding. One electrical engineer and several other mine personnel have been interviewed concerning mine power system grounding practice. Already several aspects of the mine grounding system have been marked as requiring special attention.

Jan 1, 1975

The richer, shallower sapphire deposits of the New England region of New South Wales which have been traditionally mined by the small miner are almost worked out. Larger mining and exploration companies are replacing the small miner and exploring for the primary source of sapphire or lower grade alluvial deposits.   Although in recent years considerable exploration effort has been directed at locating the primary source, commercial exploitation of sapphire is still restricted to the working of alluvial deposits.   If the Australian industry is to compete against Asian and African producers it must use cost effective exploration, mining) processing and marketing methods.

Jan 1, 1990

Recovery of Precious Metals from Chloride Solution by Magnetite The development of environmental-friendly lixiviants as alternatives to cyanide and the increasing recycling activities to recover precious metals from waste materials have prompted researchers to find efficient methods and alternative sorbents to recover precious metals, such as Au and Pt, from aqueous solutions. This study explored the use of magnetite (Fe3O4) as a sorbent to recover Au and Pt from chloride solutions. Magnetite is a semiconductor and has the capability of transferring electrons both within the solid state and across the solid-liquid interface and has the ability to reduce metal species on its surface. The sorption of AuCl4- and PtCl62- from NaCl solution on commercial grade magnetite powder was investigated by batch-sorption experiments. The effects of pH, contact time, NaCl concentration and precious metal concentration on the recovery were studied. Sorption experiments revealed that magnetite exhibited selectivity towards other metals with the strongest affinity for Au. Both Au and Pt recoveries showed similar pH dependence curves, with peaks at pH 6 - 7. At this pH range, a maximum of 4.4 ¦mol Au/g Fe3O4 and 3.0 ¦mol Pt/g Fe3O4 were recovered after 24 h at an initial metal concentration of 0.05 mol/m3. Increasing the initial precious metal concentration increased the Au and Pt uptake amount by magnetite. It was also observed that the recovery decreased with high NaCl concentrations. The SEM images of the magnetite particles after the treatment showed that gold, which was confirmed by the EDX analysis, agglomerated and were deposited on Fe3O4 surface.

Sep 13, 2010

By Oliver Bowles

"INTRODUCTION Slate has earned a high reputation as a roofing material, carefully selected and properly placed it is rainproof, attractive, and extraordinarily durable. Despite there qualities in its favor, the slate industry during the past 30 years has suffered marked reduction in volume of sales. An increase in building construction and general improvement in business will doubtless bring renewed activity, but considerable ground has to be recovered before the industry can become prosperous. Influences tending to dwarf this long-established industry producing materials of world-wide reputation are analyzed briefly in the following pages in the hope that they may be rectified.HISTORY OF SLATE PRODUCTIONFigure 1 shows graphically the rise and fall from year to year of sales of roofing slate since 1885. In quantity, the peak was reached in 1902, and the most serious decline was from 1912 to 1918, sales at the end of this 6-year period being only one third those at the beginning. Unlike most building materials, slate experienced only a slight recovery in volume of sales during the post-war period, 1920-29. The value closely parallels the volume up to the World War period. Subsequently, however, as unit values increased the aggregate value rose sharololy above the volume curve, attaining in 1928 the point reached in 1903, although the Lumber of squares sold was scarcely one third as great. The increased unit value was due partly to larger sales of heavy architectural grades."

Nov 1, 1933

By Charles Taschereau

The statements made in this presentation contain certain forward-looking statements concerning potential developments affecting the business, prospects, financial condition and other aspects of Canada Lithium Corp. The actual results of the specific items described in this presentation, and the company?s operations generally, may differ materially from what is projected in such forward-looking statements. Although such statements are based upon the best judgments of Canada Lithium Corp. management as of the date of this presentation, significant deviations in magnitude, timing and other factors may result from business risks and uncertainties including, without limitation, the Company?s dependence on third parties, general market and economic conditions, technical factors, the availability of outside capital, receipt of revenues and other factors, many of which are beyond the control of the Company. Canada Lithium Corp. disclaims any obligation to update information contained in any forward-looking statement. Toronto Stock Exchange: CLQToronto CLQOTCQX: CLQMFOTCQX: CLQMF

May 1, 2011

By Carl Bertrand, Patrice Nadeau, Claude Bazin

"Rio Tinto Fer et Titane processes the ore extracted from the Lac Tio orebody to concentrate the hemo-ilmenite (FeO.TiO2-Fe2O3) mineral that is subsequently smelted to produce pig iron and titanium oxide slag. The ore is crushed, heat treated (roasted) and concentrated using dry magnetic separators. This paper describes a model to predict the magnetic susceptibility of the roasted ore and its behaviour in the magnetic separation plant. The model uses a classification of the ore as a function of the size and magnetic susceptibility of the particles. A subsequent division into mineral species allows the simulation of the magnetic separation process. The model is used to assess various operating options when process disturbances occur.INTRODUCTIONOre processing operations consist of ore size reduction followed by the recovery of valuable species in a concentrate that is subsequently sold for its minerals or metal content. The concentration processes are based on the physical and/or chemical properties of the minerals contained in the ore. Flotation is typically used to recover minerals of base metals such as copper, zinc, lead or nickel. Iron ore and other dense minerals are typically concentrated by gravity separation processes. Magnetic separation uses the magnetic properties of the minerals to concentrate magnetite and other minerals, to clean coal concentrate and to recycle ferrosilicon for dense separation processes (Brophy, 1985).Magnetic separators can be divided into low and high intensity separators and high gradient magnetic separators (Gillet, 2008). Most of the low gradient magnetic separators are built as rotary drums that are operated in wet or dry conditions. Dry magnetic drum separators are used by Rio Tinto Fer et Titane in Sorel-Tracy, Canada to concentrate hemo-ilmenite from the ore extracted at the Lac Tio Lake mine near Havre St-Pierre, Canada. The analysis of production data suggests that process improvement could be achieved by identifying key variables for the control of the magnetic separation circuit and/or by modification to the circuit flowsheet. The use of a process model was considered to be an effective approach to conduct a preliminary analysis of the circuit with a view toward process optimization. However, the literature contains few detailed studies dealing with the modelling of magnetic separation processes."

Jan 1, 2011

By Stuart F. McTavish

Mechanically suitable grinding mills became available to the mining industry in 1908. Since then, mill operators have been searching for the best material and design with which to line the mills. These liner systems had to fulfill several criteria. Most important, they had to last long enough in an operating mill to protect its structure from the abrasive wear of the ore and the grinding media. In addition, they had to be capable of efficiently transferring the energy from the mill to the mill charge in order to facilitate the grinding process. And these liners had to be easy to install and remove. The first liners used were generally made of cast white iron, Hadfield manganese, unalloyed high-carbon steel and composites of steel and concrete or cemented in flint blocks or natural stone. In the early 1920s, pieces of solid rubber truck tires were used as emergency repairs for broken cast metal liners. Thus was rubber first introduced as a mill liner material. The first patent for rubber mill liners was awarded in 1921 to James Denny and Rolla Watson, both of the Coniagas Mine in Cobalt, Ontario, and to Dale Barnum of the Comstock Lode in Virginia City, NV. This original design was covered under US Patent No. 1470597. It had a fabric backed rubber that was bonded to the shell of the mill.

Jan 1, 1990

By R. G. Garrett, A. J. S. Geddes

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The 1986 geochemical survey was successful in recognising all the previously known mineral occurrences of significance in Jamaica, in outlining areas not previously believed to have mineral potential and in stimulating fresh appraisals of old occurrences in terms of their potential for new commodities. This has resulted in a very significant increase in mineral exploration activity in Jamaica

Jul 1, 1991

By Jacqueline H. Jansky

The Mine Safety and Health Administration (MSHA), U.S. Department of Labor, did a linear analysis for a new underground coal mine in Grant County, WV, through the interpretation of LANDSAT imagery and high-altitude, color-infrared aerial photography, to identify areas of potentially unstable roof in advance of mining. The Bureau of Mines included this mine in its ongoing study of the correlation between geologic features and linears. Three years after the analysis, after mining had progressed through the plotted linears, a cooperative Bureau-MSHA study evaluated the effectiveness of the linear plot in predicting areas of unstable roof and defined the geology associated with the linears. Adverse roof conditions at this mine include roof falls, potted-out roof, water inflow, and local areas requiring supplemental support. At the time of this study, 34 pct of the mine workings were within 200 ft of a plotted linear. Fifty percent of the adverse roof area in the mine occurred within this area. The primary geologic anomaly associated with the linears is an increased frequency of jointing. The majority of the plotted linears coincide with the prominent joint orientations. Additional features observed in the linear zones include roof rolls and a sandstone channel that cuts into the coal seam.

Jan 1, 1983