Search Documents

It has been proven theoretically and experimentally that the use of 10 - 30 per cent DRI in blast furnace along with iron ore or sinter results in lower coke rate and higher productivity. However, to-date this remains unpractised on a regular basis mainly because of economic reasons. The DRI produced by several methods are expensive and difficult to store/handle in large quantities because of its reactive nature and thus DRI in blast furnace remains unacceptable.

Jan 1, 1999

By K Lownie, R Sani, A Sianturi

Part of the PT Freeport Indonesia (PTFI) mine production is in the process of transitioning from the deep ore zone (DOZ) mine to the deep mill level zone (DMLZ) mine. The DMLZ mine is the next lift in the caving series and lies 500 m below the current DOZ footprint.In order to reduce the need for a very expensive additional ventilation system for the DMLZ mine, it was decided to reconfigure some infrastructure and upgrade the performance of the three existing DOZ mixed flow ventilation fans in situ, reducing the new fans required to two. This was far less costly than providing complete new installations.These fans are installed in individual underground chambers in DOZ mine exhaust drifts and connected to the DMLZ mine exhaust drifts system in 7 m × 7 m airways size, through sets of 6 m diameter by 500 m high raises.The upgrade process involved replacement of motors, fan shafts and bearings. The existing 1600 kW DOZ mixed flow fans are 3500 mm diameter and operate at a speed of 595 rev/min and were originally designed to deliver 390 m3/s at 3.3 kPa. Efficiency optimisation may be required at a later date.The upgraded DMLZ fans are required to deliver 425 m3/s at 3.7 kPa and it was necessary to increase in motor size and speed to 2200 kW at 710 rev/min. This paper will discuss the fan upgrade project and in particular the integration of an unusual ventilation system, which is based on the semi parallel operation of multiple large fans.CITATION:Sani, R, Sianturi, A and Lownie, K, 2017. Operation of deep mill level zone mixed flow fans after the first fan upgrade – a parallel fans case study, in Proceedings Australian Mine Vent Conference 2017, pp 285–292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Liane J. Terrill

Rockbolt failures at the Waste Isolation Pilot Plant have been recorded since 1990 and are categorized in terms of mode of failure. The failures are evaluated in terms of physical location of installation within the mine, local excavation geometry and stratigraphy, proximity to other excavations or shafts, and excavation age. The database of failures has revealed discrete areas of the mine containing relatively large numbers of failures. The results of metallurgical analyses and standard rockbolt load testing have generally been in agreement with the in situ evaluations.

Jan 1, 1995

By A. Krause

Shovel-truck systems for loading and hauling material in open pit mines are now routinely analysed using simulation models or off-the-shelf simulation software packages, which can be very expensive for once-off or occasional use. The simulation models invariably produce different estimations of fleet sizes due to their differing estimations of cycle time. No single model or package can accurately estimate the required fleet size because the fleet operating parameters are characteristically random and dynamic. In order to improve confidence in sizing the fleet for a mining project, at least two estimation models should be used. This paper demonstrates that the Machine Repair Model can be modified and used as a model for estimating truck fleet size in an open pit shovel-truck system. The modified Machine Repair Model is first applied to a virtual open pit mine case study. The results compare favourably to output from other estimation models using the same input parameters for the virtual mine. The modified Machine Repair Model is further applied to an existing open pit coal operation, the Kwagga Section of Optimum Colliery as a case study. Again the results confirm those obtained from the virtual mine case study. It is concluded that the Machine Repair Model can be an affordable model compared to off-the-shelf generic software because it is easily modelled in Microsoft Excel, a software platform that most mines already use. This paper reports part of the work of a MSc research study submitted to the University of Witwatersrand, Johannesburg, South Africa. Keywords: simulation, bunching, probability distributions, cycle time, queuing, matching, shovel-truck, OEM.

Jan 1, 2007

By H. Lyn Bourne

This is the fifth annual tabulation of mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data. There are also 60 new entries. In addition to royalty information, some entries show the cost of purchased reserves. Two articles relative to the evaluation of minerals reserves appeared in December, 1986. R.H. Paschall (In the Aggregate, ME, p 1139) wrote a good article, although it lacked specific royalty data. However, this author takes exception to two ideas in Paschall's column. Paschall contends that the royalty rate does not affect the mineral appraisal. This present author could not disagree more. Paschall also claims the location of an industrial mineral deposit is the only serious or practical caveat in comparing royalties. Comments received here from readers helped make the list of caveats that are cited each year. The readers will decide which factors influence the mineral value for their commodities of interest. Paschall's point about the relationship of the parties who are negotiating a royalty agreement is important and very well taken. The other article, written by William Vernon (Pit and Quarry, December 1986), gives a step-by-step process on how to conduct a mineral appraisal. The article cites three reasons for an appraisal: transfer rights; collateral for a loan; and taxation. A fourth reason is to establish adequate compensation for reserves lost through condemnation. This author has appeared in several court cases where compensation for loss of mineral reserves through condemnation required a mineral appraisal. Royalty rate becomes an important factor in the appraisal process, although the Pit and Quarry article refers to that part of the valuation equation as "profitability." Both articles were well written and are recommended reading for those interested in mineral valuations. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation - especially significant for most industrial minerals; • market conditions both for the commodity and the company acquiring the right to mine; • quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give: • the location by state, US geographic area, or Canadian province ; • the cost - R for royalty and P for purchased cost; • the year in which the lease or purchase agreement occurred; and • comments or footnotes for more information. The cost column requires more explanation. The units may refer to cubic yards (/cu yd), cubic feet (/cu ft), short tons (/T), or acres (/A). 1 cu yd = 0.76 M2 1cuft = 0.28m3 1 st = 0.9072 t 1 acre - 0.4047 ha or m2

Jan 7, 1987

This paper characterizes the copper cycle, that is, the flows of copper entering and leaving the African economy over a one-year period (1994). The major flows over the entire life-cycle of copper are examined; these include production (mining, milling and refining), fabrication of semi-products and manufacturing of finished products, use, and the waste management system. The results reveal that substantial amounts of copper (of order705 Gg/yr) are mined in Africa; of that amount, about 70 per cent is exported following processing, 18 per cent is utilized by African fabricators, and 12 per cent is discarded. The flows of copper products from African fabricators and product imports from other continents exceed product discards by large amounts. This difference, about 0.25 kg Cu/capita/yr on average, is added to in-use stock, largely as wire, plumbing tube, and in electronics. Some 65 per cent of the copper in discard flows is contained in electrical and electronic products, where it is relatively easy to collect and process for reuse. About a third of the copper discard flows known is recycled. The actual percentage is almost certainly higher because of informal (and unrecorded) recycling. Much of the remaining discarded copper is diluted into the municipal waste stream, where recovery and recycling are probably not economically justified. Keywords: material flow analysis, resource management, material budgets, copper, stocks and flows, systems analysis, Africa, developing country

Jan 1, 2003

By P. Schmieder

"The close vicinity of mining companies to other sites that are used for commercial and residential purposes or to areas under conservation as well as the fact that the people become more and more sensitive to emissions have led to a negative attitude towards mining operations in the neighborhood. It is above all the use of drilling and blasting techniques that give rise to objections, in the course of which demands for more environmentally-friendly production methods have been voiced. It is in this context that production methods without the use of explosives are considered as an option. After all, the use of such production methods is the only alternative for some quarry operators. The question is what are the true benefits of these techniques and what is the relation between a possible improvement of the environmental effects on the one hand and the technological potential as well as the costs on the other. It is intended to assess the mining techniques for solid rock in their entirety. This paper will therefore look at the aspects for assessing mining techniques in the context of their environmental impact and the costs."

Jan 1, 2005

By Wern-ping (Nick) Chen

The Florida Department of Transportation District 6 (FDOT D6) began a study in 1987 for a master plan to improve the traffic circulation and congestions between the Port of Miami (POM) and downtown Miami, FL. This study included a tunnel connection between two man-made islands, the Watson and the Dodge islands. Though a finding of no significant impact (FONSI) was completed in 1992, the project remained on hold for about 10 years. In 2002, Florida Turnpike took over this project, re-evaluated its benefits to the lo-cal communities, determined its feasibility (specifically the tunnel options) and established a probable cost. In 2005, the FDOT D6 regained its charge over the project and concluded that a bored tunnel under Biscayne Bay is feasible. Its primary components are: ? Widening of the MacArthur Causeway Bridge, to accommodate truck traffic to the Port of Miami. ? A tunnel connection between Watson Island and Dodge Island, where the POM is located. ? Connections to the POM roadway system, either for the traffic from the city of Miami or for the truck traffic from I-395 to the POM. The project will improve access to and from the POM and provide a dedicated roadway connector linking the POM with the MacArthur Causeway (State Route 41/1) and I-395, specifically for the trucks in and out of the POM without going through downtown Miami. As identified in the project information memorandum (PIM), its primary objectives are to: ? Improve access to the POM, helping to keep it competitive and ensuring its ability to handle projected growth in its cruise and cargo operations. [ ] ? Improve traffic safety in downtown Miami by removing POM traffic, trucks and buses from the congested downtown street network and, in doing so, facilitate ongoing and future development plans in and around downtown Miami.

Jan 1, 2009

By M Wimmer

LKAB operates two underground iron ore mines located in the northern part of Sweden, both using sublevel caving (SLC) as the mining method. Knowledge of the mechanisms of gravity flow is important since it affects both ore recovery and waste dilution. This paper describes results from a large-scale field test carried out at the Kiruna mine with a focus on gravity flow. It is part of Work Package 2 in the I2Mine project financed by the EU. A total of ten rings were blasted. Smart Markers based on radio frequency identification technology were used to monitor the gravity flow. An accurate delineation of the isolated extraction zone requires reliable detection of all recovered Smart Markers and precise knowledge of the 3D position of the markers within the burden. It was therefore necessary to carry out borehole deviation measurements (collar, alignment and trajectory). The blast performance was monitored by high-speed filming, near-field vibration monitoring and velocity of detonation measurements. Three-dimensional stereo images were taken from the drawpoint and the loaded bucket after each mucking cycle. Based upon that, fragmentation was assessed both in 2D and 3D. Furthermore, volumetric differences were determined at the drawpoint, which reflects the mobility of loaded material. For draw control, the Fe content is estimated by measuring weight and assuming a full bucket. The measured volume of rock in each bucket further improves this estimate. Possible flow disturbances occurring at the drawpoint were revealed by video recording. Two-dimensional laser scanning was carried out during mucking to track the position of the bucket and estimate the position and slope of the muck pile.The results from this test clearly show that the gravity flow in the large-scale sublevel cave in Kiruna mine is often of disturbed character. Standard draw occurred only in three rings and shallow draw in the remaining seven rings. In five cases, shallow draw developed towards standard draw, but occurred at rather late stages during extraction (70–125 per cent). The maximum width of the draw varied between 10 m and 13 m except for one ring (6 m). The draw reaches the cave rather early (5–25 per cent extraction) in shallow draw situations and much later (about 50 per cent) during standard draw. Waste originates from above in most cases, while more significant portions often occur at about 20–45 per cent extraction.All the results from this extensive field test are not yet fully analysed, and further field tests are planned. A more detailed insight into gravity flow in large-scale SLC and possible influence by drilling, blasting and the mucking procedure is expected in the future.CITATION:Nordqvist, A and Wimmer, M, 2016. Holistic approach to study gravity flow at the Kiruna sublevel caving mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 401–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By P K. Smith, R J. Ryan, W R. H Ramsay, D C. Arne, F P. Bierlein

Turbidite-hosted, mesothermal lode gold deposits in Paleozoic metasedimentary rocks of the Buller Terrane, western South Island have a similar geological history and genesis to the Paleozoic lode gold deposits ofVictoria, Australia and Nova Scotia, Canada. In all three regions the gold deposits are hosted by interbedded meta-sandstone and meta-argillite that have been folded and regionally metamorphosed to greenschist facies, and locally in Nova Scotia to amphibolite facies. The gold deposits are typically narrow, structurally controlled quartz veins associated with dilatant zones in reverse faults or fold-related fractures. The principal vein types include: bedding parallel or concordant veins, discordant veins, saddle reefs, and stockwork veins. En-echelon and "ac" type veins are sometimes also gold-bearing in Nova Scotia. The contrasting competency of the host meta-argillite and meta-sandstone beds is an important factor in vein formation, particularly for the bedding parallel veins, which are typically developed within meta-argillite beds or along the contacts between meta-argillite and meta-sandstone. Veins found within meta-sandstone units are generally discordant. The deposits in Victoria are well known for their bedding-parallel veins, saddle reefs ( Bendigo ) and leather jacket reefs (Ballarat). Bedding-parallel veins are also common in Nova Scotia , along with a few examples of saddle reefs. In contrast, vein formation probably occurred later in the deformation history of the Reefton and Lyell goldfields, with most veins being bedding discordant and more typically aligned with the axial plane cleavage of the folds rather than bedding planes. The quartz lodes in one deposit, Globe-Progress, strike approximately perpendicular to the bedding and fold axes. No saddle reefs have been recorded from the Buller Terrane. Mesothermal vein morphology reflects the amount of fmite strain, the strain rate, competency contrasts, lithotypes, and the confirming pressures to which the system was exposed. On the basis of comparable depositional depths and rheologies of the host rocks, a controlling factor influencing the development of different vein styles (and timing) might be finite strain, as exemplified by the tightness of folding in the host rocks. Folding appears to be tighter in the Victorian rocks than in either the Buller Terrane or Nova Scotian rocks.

Jan 1, 1999

By S Thomson, M Lovitt, T Purvis, C te Kloot, T Nguyen, Z Liu

Ernest Henry Mine (EHM), located in north-western Queensland, is an underground copper/gold sublevel caving operation currently producing over 6 Mt/a of ore. The mass mining method of sublevel caving (SLC) used at EHM involves systematically blasting a series of uphole rings in parallel ore drives and drawing the broken ore using a top-down approach. Each ore drive contains multiple precharged rings to prevent having to charge in close proximity to the brow of the previously fired ring; however, the current initiation system still involves ‘hooking up’ all detonator lead cords of the first precharged ring. The unstable nature of a rill and working close to a brow presents hazards to personnel completing the hook-up process. There is also a business risk of ore loss when damaged ground support completely prevents access to the next precharged ring. If the hook-up step could be eliminated, the risk to personnel and the business would be significantly reduced.EHM engaged Orica Mining Services in 2016 to trial their WebGenTM 100 – wireless electronic blasting system (WEBSTM) for the first time in an underground mining environment. Having successfully signal-tested the equipment, two test holes were initiated, followed by a single production ring and then multiple production rings. In total, 30 production rings were successfully fired underground at EHM in 2017. To do this, WEBSTM was successfully integrated into EHM’s current charging and firing process, resulting in no business delays or loss to production. None of the 30 rings required hooking up and all were initiated from the surface with no personnel underground. A high level of ownership from all personnel involved ensured the trial was a success, and provided scope for wireless detonators to be used successfully on a large scale – both at EHM and other sublevel caving operations. WEBSTM is now a proven example of technology that can be used to improve safety in the mining industry, through eliminating the need for personnel to work in hazardous areas.CITATION:te Kloot, C, Liu, Z, Purvis, T, Thomson, S, Lovitt, M and Nguyen, T, 2017. Improving safety through technology – Orica wireless electronic blasting system trials at Ernest Henry Mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 39–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By J. He

The separation performance of a raw coal sample from South Africa based on the dense gas-solid fluidized bed beneficiation technique was investigated. Analysis showed that the raw coal sample distributes mainly in the -50+6 mm size range with the -1.6 g/cm3 density fraction accounting for 78.20% of the cumulative mass distribution. A flow sheet of the sequential coal beneficiation technique was introduced. The experimental and simulation results of the hydromechanical and density distribution stability indicate that the dense gas-solid fluidized bed could provide a stable separation environment with uniform density fluctuations under suitable operating conditions. With the application of this technique on the raw coal sample, the separation results show that three products, consisting of 73.25% clean coal with an ash content of 9.59%, 11.31% middlings, and 15.44% gangue were effectively separated at two different densities of 1.82 g/cm3 and 1.57 g/cm3. This study provides an effective flow sheet for achieving the high-efficiency separation performance on raw coal from arid areas. Keywords dense gas-solid fluidized bed, dry coal beneficiation, density distribution, separation efficiency.

Jul 1, 2013

By W. Hustrulid

In the mid-to-late 1800’s the U.S. mining industry was on the threshold of nearly a century of golden times. Nearly every state had a prosperous and growing mining sector. The importance of the industry was reflected in the creation of the state school of mines. Today, with the depletion of readily available mineral reserves, much of the U.S. metals mining industry is considered to be in a sunset phase. The same is true with the mining schools that serve the industry. However, the United States is still a major consumer of the world’s minerals and requires a dependable supply of both minerals and minerals professionals. In his 2002 Jackling Lecture “You Can’t Make a Silk Purse Out of a Sow’s Ear” the author presented a list of concerns, propositions and recommendations. In this follow-up paper, the author further explores the subject through the presentation of a detailed case example focusing on the iron mining industry of Minnesota and minerals education at the University of Minnesota.

Jan 1, 2004

By L. Hanschar, C. Bwalya, E. Mokola, K. Musonda, A. Makayi

This paper describes the installation, commissioning and operation of porous plugs featuring nitrogen gas purging in both Anode Furnaces at the Kansanshi Copper Smelter (KCS), a greenfield copper smelter which commenced operation in March 2015. The decision to install porous plugs was taken in November 2016 and the facilities were successfully commissioned on both anode furnaces in October 2017. The project was successful and has demonstrated the following process improvements: 12.2% reduction in main burner fuel consumption Larger average charge size, due to fewer accretions; 17 minute decrease in average refining cycle times Improvements in slag skimming operations Improved casting rates INTRODUCTION Porous plugs The application of porous plug technology in copper smelter anode furnaces is well established around the world. Vukovic and Gamweger (2017) and Wallner (2004) noted that the stirring and mixing action induced by the injection of inert nitrogen gas into the molten copper via porous plugs has potential benefits in the following areas: Homogenization of the temperature and composition of the molten copper resulting in Reduced fuel consumption Less tendency to overheat slag (reduced risk of refractory attack) Less slag produced with a lower degree of oxidation (lower rate of refractory wear) Less tendency for buildups to form Improved environmental performance (produce low sulphur blister at Peirce Smith converters) Elimination of buildups inside the furnace and potential for larger charges per cycle Reduced processing times and potential for shorter cycle times More efficient skimming of anode slag Shorter skimming time Less copper carry over to Peirce Smith converters Very little slag remaining in the furnace (reduced potential for buildups to form)

Jan 1, 2019

By C. Gosselin, G. M. Payenzo, C. Bazin, M. Desnoyers, G. Chevalier

"ArcelorMittal Mines Canada operates hydraulic classifiers to reduce the silica content of an iron oxide concentrate from 4.5% to less than 1.2% SiO2. Sampling campaigns were conducted to develop a preliminary model for the hydraulic classifier. Results show that iron oxide and quartz are respectively concentrated in the coarse and fine size fractions of the classifier feed. The mineral partition curves in the classifier and the size distribution of the minerals in the feed are used to simulate the classifier operation in order to identify the source of variability observed in the daily plant production data. Results indicate that most of the variation is probably caused by unsteady operating conditions of the classifiers.INTRODUCTION Hydraulic classifiers are a class of gravity separation devices (Wills, 1992) used to classify particles according to their size and specific gravity. Hydraulic classifiers also known as density separators (Hearn, 2002) combine hindered settling and upward flow of water to selectively entrain light particles to an overflow stream. Denser particles settle to an underflow stream. Hydraulic classifiers are used for various purposes ranging from cleaning of coal (Das, Sarkar, & Mehrotra, 2009), recovery of chromite from plant tailings (Kumar, Tripathy, & Rao, 2009) to upgrading iron oxide concentrate (Hearn, 2002). ArcelorMittal Mines Canada operates several hydraulic classifiers to upgrade an iron oxide concentrate by removing fine quartz and other light minerals from hematite that is the main iron oxide mineral. A project was initiated to analyze the operation of the classifier in an attempt to identify the source of the variability in the production results and to assess the potential of increasing iron recovery in the classifier. One possible disturbance for the classifier operation is the change in the classifier feed composition and size distribution, while the other considered disturbance is the operation of the classifier. The paper is divided into five sections. The first section summarizes the ore processing sequence for the production of iron oxide pellets to identify the position of the hydraulic classifier in the process. The second section describes the hydraulic classifier. The third section discusses the sampling campaigns conducted on the hydraulic classifier. The method used to process the data from sampling, the results of the data processing and simulation of the classifier are discussed in the remaining sections."

Jan 1, 2012

A dedicated tunnel construction version of the Caterpillar 328D LCR compact radius excavator is proving highly productive on the A9 Autoroute construction project near Visp, in Switzerland. It is the first machine of its kind to operate on a Swiss contract and uses a special dedicated front attachment designed and constructed by German Caterpillar dealer Zeppelin. The machine offers a powerful, stable and compact solution for tunneling contractors. A rear overhang of just 305 mm (12 in.) provides a tail swing radius of just 1.9 m (6.2 ft). The 328D LCR is ideal for the restricted working areas within a tunnel construction site. The machine is equipped with the wide tracks from the 330D L conventional crawler excavator, ensuring maximum stability when operating. In addition, the boom mounting has been moved further toward the center of the machine for the tunnel model, creating an increased lift capacity over the front end compared with a standard 325D L. The boom itself features a robust box section construction, with high-strength steels, additional supporting struts and reinforced bearings for maximum durability. All pins have hard-chromium plating for optimum protection against wear. Stick digging force is a powerful 134 kN, with up to 212 kN of bucket digging force available, for maximum penetration in blasted material. The 328D LCR is also equipped with a heavy-duty dozer blade as standard. This ensures outstanding stability when working and providing a useful secondary tool for clearing and leveling within the jobsite. Two 45° tilting mechanisms in the boom construction, allow the boom to be swung to 45° on either side of the machine. So the specially designed attachment linkage provides increased rollback for access to the roof of the tunnel. A Caterpillar CW45S mechanical quick-coupler allows rapid changes between specialist tunneling attachments, standard Caterpillar buckets and a range of Caterpillar work tools. The machine is powered by a Caterpillar C7 diesel engine. This six-cylinder EU Stage IIIA diesel motor [ ] offers 8 percent more power than its predecessor, with 140 kW (190 hp) available at just 1,800 rpm. Caterpillar?s ACERT combustion technology results in lower fuel consumption and reduced exhaust emissions. However, the tunnel machine is also equipped with a diesel particulate filter as standard, to further cut exhaust gases within the tunnel working. The 328D LCR is designed for use in transport tunnels of 6.8 m (22.3 ft) in height. With the tunneling boom in place, the machine has an operating weight of 42,540 kg (93,783 lbs), yet retains a transport height with the tunnel boom of just 3.9 m (12.8 ft). Transport width with 600 mm (23.6 in.) track shoes, is just 3.2 m (10.5 ft). On the A9 tunnel contract, the machine is being used by a consortium of Swiss and Austrian companies working for the canton of Valais? Routes Nationals Construction (RNC) department. The 31.8-km (19.7-mile) A9 Autoroute construction project will connect Sierre in the west and the town of Brig to the east. The tunnel that is bypassing the town of Visp is just one of a number along the mountainous route.

Jan 1, 2009

Autogenous-Carrier Effect and Gangue Influence in Fine Particle Flotation of Ilmenite/Titanaugite System

Sep 13, 2010

The Barrick Zaldivar mine is an openpit, heap-leach copper mine in Region II of northern Chile at an elevation of 3,300 m (10,826 ft), approximately 1,400 km (870 miles) north of Santiago and 175 km (109 miles) southeast of the port city of Antofagasta. In 2006, Zaldívar produced 307 million lbs of copper, with reserves estimated at 5.7 billion lbs. The mine uses conventional methods of openpit mining: Pure cathode copper is produced by three stages of crushing and stacking the ore, followed by heap leaching and bacterial activity to extract copper from the ore into solution. A solvent extraction and electrowinning process then removes the copper from solution and produces the cathode copper. A flotation plant also recovers copper contained in the fine fraction of the crushed ore. In 2006, an existing A-frame structure that covered copper ore from the mine?s secondary crushing operation was damaged beyond repair. The material delivery configuration of this original structure had the conveyor carrying incoming ore directly over the low roof to drop ore into the building at its peak, and ore trickling from the sides of the conveyor had accumulated on the roof, overloading it. A better solution had to be found, and fast: First, the Chilean Commission does not permit uncovered piles of this type since the extremely fine material leads to serious pollution problems. Second, Barrick Zaldivar is very concerned about worker safety, and the amount of dust created by the uncovered pile was not acceptable. Finally, some amount of copper was lost in the dust generated by the winds of the Andes. The major issues faced by Barrick Zaldivar in designing a new structure included:

Jan 1, 2009

From Sept. 22-24, the Las Vegas Convention Center will be home to MinExpo 2008, the world?s largest mining equipment show that comes along once every four years. Sponsored by the National Mining Association (NMA), this year?s show is on pace to be the largest ever. Nearly 1,300 exhibitors have purchased nearly 55,700 hm2 (600,000 sq ft) of booth space. At the center of it all will be some of the most impressive mining equipment that the industry has to offer. And in the shadows of the massive haul trucks, drill rigs and bulldozers, attendees will be able to see the latest and greatest products including hand tools; the latest in automation and robotics; safety and communications equipment; longwall mining equipment; engines and parts; materials handling and processing equipment and services; pollution control equipment; reclamation equipment and services; computer applications; consulting and financial services and more. While many companies will be on hand to display the tried and true, there will also be plenty of new things to see. ?We anticipate that a whole range of new products will be introduced at the show,? the NMA said of the show that has been called the world?s richest deposit of mining technology, services and products. In addition to the show that will take place in Center Hall and North Hall of the Las Vegas Convention Center, MinExpo 2008 includes a conference program with 20 educational sessions that will tackle the most timely and pressing issues affecting the mining industry. Many of the industry?s top professionals will lead the discussions.

Jan 1, 2008

By Richard L. Rains

The Bureau of Mines made a study of mines and prospects of the Benton Range RARE II area (No. 5056), Mono County, California in October and November 1980. The study area is west of Owens Valley and 30 mi (40 km) north of Bishop, California. The mineral deposits were evaluated by examination of mines, prospects, and mining claims by the Bureau of Mines. Geological, geochemical, and geophysical studies were conducted by the Geological Survey. The principal mineral commodities of the Benton Range RARE II area are gold and silver but tungsten deposits may also extend into the area. Properties with resources are listed in table 1; their locations are shown on figure 1.

Jan 1, 1982