Search Documents

Based on the examination of thirty sets of contiguous matte and slag samples taken from industrial nickel smelters a relationship is predicted between oxidic nickel in slag, oxygen in matte and the Ni/Fe ratio in the matte. Oxidic nickel in the slag is found to increase with an increase in oxygen content of a matte of constant Ni/Fe ratio, and it is proposed that the relationship may be used to predict nickel solubility in slag from a knowledge of matte composition alone.

Jan 1, 1980

By Gift Chisakuta, Bravo Mbao, Nils Schwarz, Angus Feather, Anthony Mukutuma

Bwana Mkubwa is a 50 000 tons per annum copper cathode producer, owned by First Quantum Minerals and located in Ndola, on the Zambian Copperbelt. The Bwana Mkubwa solvent-extraction circuit was started up in 1997. In 2002, the plant began treating ore from First Quantum?s Lonshi mine located in the Democratic Republic of Congo. The Lonshi ore is exceptionally fine and the amount of solids in the feed solution reporting to the solvent-extraction feed solution increased dramatically. Initially, crud was filtered in a filter press, but this rapidly blinded and seldom produced anything better than a wet sludge containing large quantities of organic. In December 2003 the decision was made to install a Flottweg Z4E-3/441 Tricanter® centrifuge to recover organic from the crud. The installation was completed in June 2004 and has since led to significant improvements in plant operability and savings in organic consumption.

Jan 1, 2007

By Greg S. Williams, Richard W. Givens

This paper examines the effect of prill size consistency, internal panicle density, and oil absorbency on Ammonium Nitrate Fuel Oil (ANFO)-emulsion blends. By analyzing these physical properties of prill and the nature of the blending process, a mathematical model has been developed to theoretically predict blend densities. Calculated densities can now be compared to actual field densities to give an operator a basis for comparing various manufacturers’ emssions and Ammonium Nitrate (AN) during bid solicitation. The lowest priced emulsion and/or AN may not be the most economical, due to the impact of specific physical characteristics. These factors dictate the blending mechanics and resulting density yields for various mixes. The research was driven from observed ‘field’ mixing relationships and data. Ultimately, such a model can be an effective tool in evaluating blends from a cost and performance basis.

Jan 1, 1992

By Clinton C. Knox

Attention of mine operators and engineers in the Picher zinc-lead field has been drawn increasingly in recent years to marginal ore deposits lying at greater than normal depth below surface in the marked structural depressions known as the Miami and Bendelari troughs. Not only mining but prospect and development drilling is relatively costly in the bottoms of the structural depressions known as the. Miami and Bendelari troughs which cross the center of the Picher field. Nevertheless, operations by various mining companies in recent years have shown that no insuperable problems exist, and with the gradual lowering of grade cut-offs throughout the field, certain potential deep-ore areas, previously only partly explored seemed worthy of further investigation. Some such areas were called to the attention of Bureau of Mines engineers by lease holders and operators, while others were noted in the course of Bureau's systematic investigation of Tri-State ore reserves. The writer was assigned to make a study of. those possible "trough extensions," in the course of which all available nine maps, drill logs, and prior reports were assembled. Subsequently 41 churn drill holes were bored by the Bureau in the periods October 1944 to May 1945 and October 1946 to April 1947. The general area under investigation this project is indicated on figure 1, which likewise shows its relation to nearby towns, roads, and railroads. The location of individual deposits included in the report is indicated more clearly on figure 3. Minable ore was found in only two holes, and the structural information procured by drilling was less encouraging than anticipated. This report, however, presents all factual data obtained, in the belief that they may be useful in subsequent prospecting and development projects in the areas investigated. There are also set forth some of the stratigraphic data relative to the Picher field ns a whole and the Miami and Bendelari troughs which were assembled in the preliminary investigation of this project.

Jan 1, 1949

By Jesús E. Gómez

In the Summer of 2011, emergency repairs to the Jefferson Memorial North Plaza and Seawall were completed. These repairs were necessitated by settlement and lateral movement of the seawall and North Plaza which prompted the National Park Service (NPS) to initiate an investigation as to the possible causes of the movement, and commission a design for its mitigation. Information gathered from extensive instrumentation on site led to the design of a movement mitigation scheme that included demolition of the Ashlar Seawall and reconstruction of a new seawall. The new seawall foundation is an A-Wall consisting of vertical caissons and battered pipe piles connected to the seawall itself. The scheme provides resistance to future vertical and lateral movement of the North Plaza and the new seawall. Repair to the seawall and plaza began in December 2009, and was completed in August 2011. This paper discusses the mechanisms believed to be responsible for settlement and lateral movement, summarizes the procedure followed for design of the mitigation, and describes the construction methods and some challenges faced during the repair.

Jan 1, 2011

The Canada Centre for Remote Sensing (CCRS) has developed an airborne sensor, the SWIR Full Spectrum Imager (SFSI) which detects in the short wave infrared range of the solar spectrum from 1220 to 2420 nm. In June of 1995, a demonstration flight was undertaken in the state of Nevada with the support of the companies listed above. The focus of the flight was to collect image data over well known mineral deposits with the objective of evaluating the applicability of this sensor to alteration mineral mapping. Some of the Nevada sites chosen include Cuprite and Goldfield, volcanic hosted acid sulfate systems; Yerington, a structurally complex porphyry copper deposit; and Virginia City, a quartz-sericite-pyrite vein system with advanced argillic pods. Ground spectral data was collected with the PIMA-II spectrometer. Solar reflectance calibration was done by Desert Research Institute personnel at Virginia City and Cuprite. This paper will discuss the configuration of the sensor and present image and ground data for Goldfield and Virginia City.

Jan 1, 1995

By Victor Nazimko

A new technique for reaming the holes has been tested. This technique is available for reaming a hole at its deep end creating an enlarged cavity that has helicoidal grooves oriented at less than 40 degrees to the hole axis. This technique increases bolt resistance by a factor 1.3-1.62; its bearing capacity by 3 times and enhances underground roadway stability. This technique is suitable for great depth (1000m and greater) and weak wet rocks.

Jan 1, 2008

By Heinz Brandl

Box-shaped pile and diaphragm wall foundations have proved suitable for transferring heavy loads of bridges, power plants, tanks, towers or other buildings in a concentrated form into the ground. The bearing-deformation behaviour and the earthquake resistance of such "box-foundations" are superior to those of conventional pile groups. The reason lies in the reduction of lateral soil displacement and in the composite effect between concrete elements and the enclosed soil. The paper describes results of comprehensive model tests and in situ measurements, theoretical aspects and case histories.

Jan 1, 2002

By K. Bounou, K. Komnitsas

"Risk quantification may be used as a sustainable development index in the mining industry, since it encompasses both economic and social factors. In addition, it may assist in the development of a framework, which is also indirectly related to sustainable development, to prevent accidents and improve health and safety standards. However, risk quantification in the mineral sector involves diverse activities and is considered a very difficult task. Although statistical data report accident severity rates, incident rates and accident frequency rates, none of these allow for accurate risk calculations. In this paper, two risk calculation formulas, which may be used to quantify risk, as well as to identify hazardous activities in a workplace, are proposed. Numerical examples are given based on statistical data available through the MSHA database. Also a combination of a decision/fault/event tree that allows risk quantification is presented."

Jan 1, 2005

Kalgoorlie is the main mining centre of the Western Australian Goldfields. Its famous Golden Mile' has been noted for the exceptional width and richness of its goldtelluride lodes. Since the mid-1890s production on the major mines has been maintained practically continuously.Rich ore, though not as plentiful or as rich as formerly, is still (1948) being mined in places. Unexplored areas still remain within the main auriferous belt which offer reasonable chances of success with intensive exploration.Much detailed information has accumulated in recent years through the geological mapping of underground workings by some of the larger mining companies. The purpose of this paper is to correlate observations made in most of the accessible old and recent workings in the mines of the Lake View and Star group and elsewhere.GENERAL GEOLOGYRock TypesThe rock formations are:-1. Fine-grained (older) greenstones, locally referred to as calc schists. There were originally pillow lavas and other flow rocks of basic composition, now extensively chloritised and/or carbonated. Pillows and fragmental flow- tops are recognisable. Intercalated with flows near the top of the series are several beds of sediments.2. Graphitic slates and other more arenaceous sediments.Although referred to as slates, they are rarely more than well-bedded shales with poorly developed fracture cleavage:Thick bands of felsitic rock are found in places.

Jan 1, 1952

By Edward Walter

Rock excavation for tunneling projects occurs on a regular basis in the Cleveland area. These tunnels are being constructed to increase the capacity of the sanitary sewer system. Controlled blasting must be performed to remove rock in a number of phases of the project. The rock excavation for construction of a junction chamber is just one case where blasting is the safest and most efficient method available.

Jan 1, 2001

By H. Maleki

As mining continues toward deeper reserves in thick western US coal fields, the control of mining induced-seismicity has become a priority in many operations in Utah, Colorado, and Wyoming. Gradual floor heave, common in many coal mines, has historically not been a safety issue. However recent occurrences of sudden floor heave accompanied with seismicity in a few deep mines have fueled this investigation. The focus is to identify and study the mechanisms resulting in sudden heaving of the mine floor in western U.S. deep coal mines through analytical calculations and back analyses of an actual event in a cooperative mine. Based on review of available data in three mines, underground observations and back analyses of an actual event, the authors have identified the following contributing factors (1) presence of stiff stratigraphic units and thick seams mined at depths exceeding 1000-ft (2) presence of geological discontinuities reducing the in-situ strength of the coal with calculated factor of safety near 1 for the mine floor (3) mining approaching areas of higher than normal stress gradient associated with previous mining or structural anomalies or surface topographic highs and (4) an additional source of energy triggering sudden failure such as periodic caving or slip along geological discontinuities. Preliminary examination of seismic data for the actual event in the cooperative mine and underground observations excluded fault slip at the mining horizon as the triggering mechanism but highlighted the significance of weak, anisotropic strata conditions near the intersection of two faults.

Jan 1, 2009

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012

By W G. Szymczak, Leslie C. Taylor

The University of Maryland (UMD) has conducted a series of small-scale tests using explosive charges buried in saturated sand. Twelve different combinations of depth of burial of the charge and height of the target plate above the soil were tested. The target plates did not deform plastically. High-speed video was used to track the motion of the plate. The video data are analyzed to determine the position and velocity of the plate as a function of time. The results of this analysis are compared with computations performed at NRL using the BUB2D computer code. This code treats the saturated sand as an incompressible visco-plastic fluid which yields according to a Drucker-Prager (frictional-cohesive) yield surface. Comparisons of simulations with experiments are presented. In the cases examined so far, the velocity grows very quickly to a peak and then slows, first with a deceleration greater than one “g,” which then transitions to an approximately one “g” deceleration. An analysis of air drag on the plates has shown that its effect is negligible in the time span of interest. In all cases in which the BUB2D code can be applied, the computations compare favorably with the results of the data analysis. This suggests that the code and model used in the computation are properly capturing the physics of the interaction between the soil and a non-deforming plate.

Jan 1, 2007

By J. A. Finch

"A method of sampling and presenting bubbles for imaging for use in full-size flotation cells is described. The device (bubble viewer) comprises a tube attached to a sealed glass viewing chamber. The assembly is first filled with frother-containing water (to prevent coalescence) and the tube immersed at the desired location below the froth. For a few minutes bubbles are collected in the viewer free from slurry and are readily imaged. To reduce bubble overlap and the problem of defining the plane of view, the viewing chamber has a sloped side. Bubbles rise, encounter this slope, spread into a single plane and slide up. This simple expedient virtually eliminates overlap and provides an unambiguous focus plane - the underside of the sloped glass. The bubble image is captured and processed to give size data. The bubble viewer has been employed at several concentrators on different types of flotation cells. Examples of the images are given. The impact of position in the cell and the effect of changing gas rate on bubble size are illustrated. This technique provides a sensitive measure of the effects of process variables on bubble size.INTRODUCTIONDespite the extensive use of flotation in the mineral processing industry, the methodology employed for cell design is largely based on empirical rules rather than on first principles. One of the main reasons for this state of affairs is that the local flow structures encountered in industrial-scale machines are very complex. These flow structures are difficult to simulate under the controlled conditions of the laboratory and the difficulty to solve the mathematical models that treat the randomness of such flows also mean theoretical treatment is limited. Understanding flotation cell hydrodynamics requires reliable data, which involves the implementation of measurement techniques capable of performing both at the laboratory- and the industrial-scale, In addition, it is desirable that such techniques are amenable to automation to reduce extensive manual intervention in the data collection process."

Jan 1, 2002

By S. Schina

Part of the Imittos Western Peripheral Motorway in Athens is the twin road tunnel in the vicinity of American College, with 20m excavation diameter. In the paper, the environmental and other requirements, the geometry and the geological – geotechnical characteristics of the rock formations in the construction area are given. Information regarding the modeling and analysis methods that are used for the design of the temporary support, the final lining and the wedge and slope stability analysis is described thoroughly. Finally, the results of the analyses are compared with these of measurements and general remarks during the construction of the tunnels.

Jan 1, 2001

By J. A. Finch

"Much progress has been made over the last several years in the ability to measure flotation cell hydrodynamic parameters in both the laboratory and plant. These techniques have allowed fundamental research to proceed to determine the effects that frother chemistry has on the main hydrodynamic parameters (gas hold up, bubble size) as well as on the amount of froth generation and water content of froth. A research program was begun that brought together a team consisting of private companies and a University with expertise in hydrodynamic characterization (McGill), flotation reagent applications (Flottec) and chemical synthesis (Sasol N.A.) with the purpose of characterizing frother chemistries with two goals in mind: Determine which frother chemistry can provide optimized cell hydrodynamics; and, create new frother chemistries with specific hydrodynamic properties.This paper describes the key steps that were taken that led to the development of new frother chemistry for use in flotation.The first step was the characterization of the major frother chemical families in a two phase system. The parameters measured were gas hold up, bubble size, froth height and water carrying rate at different concentrations and gas velocities.Analysis of the data indicated that definite patterns existed between frother chemistry and hydrodynamics and showed that frothers could be grouped into classes. More importantly, by modifying known frothers through chemical reaction it was shown that these frothers could be moved from one class to another. As a result of this better understanding of the interdependence of hydrodynamic and chemical properties, a new frother chemistry was proposed that was predicted to perform similarly to MIBC.The new frother was synthesized and hydrodynamic testing confirmed that the chemical performed similar to MIBC. Laboratory flotation tests were conducted on two different ore types that also confirmed the similar performance of the new chemical and MIBC. Subsequently, the new product was placed on a plant for a short period of time. The results showed that the product was an excellent frother but increased the flotation rate slightly more than MIBC at the same addition rate.Further research showed that the new frother chemistry was a family of products. By changing the reaction the resultant products could be made to be slightly weaker or stronger than MIBC but that this chemistry cannot provide hydrodynamic/froth characteristics similar to strong frothers like glycols and glycol ethers. Further work is planned to conduct longer plant trials to confirm the efficacy of this new frother family."

Jan 1, 2007

By Quentin Rhoton

To benefit two endangered fish species, waterfowl and other wildlife, and water quality in the lake and downstream, the decision was made to remove levees that had been in place since the 1950s. Because the levee material was mainly dredged up lake bottom peat, it was decided to pare down the sites chosen for breaching with dozers and trackhoes. This material was spread out onsite instead of expensive removal by dumping elsewhere. Because of the instability of the final pared down levees and the lake level being at a ten-year low, it was decided to use explosives to breach four of the sites. After over five months of earthmoving and two weeks of loading holes, the levees were detonated the day before Halloween, 2007. Somehow pumpkins showed up to be part of the explosive activities.

Jan 1, 2009

By Steven J. Page, John A. Organiscak

The amount of airborne respirable dust generated from break- age of different coals varies widely. This research was conducted to identify the facets of airborne respirable dust liberation from the coal product. Laboratory crushing experiments were conducted on a range of low to high volatile bituminous coals to investigate the various factors influencing airborne respirable dust generation. Bituminous coal samples from 8 mines (5 U.S. and 3 Polish) were uniformly prepared and processed through a double roll crusher located in a low air velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific quantity of airborne respirable dust generated. The results of this investigation build upon previously published results, which indicated that a combination of several factors are associated with the generation of airborne respirable dust. One factor involved is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics, defined by Schuhmann size function parameters. However, since coals of high moist fuel ratio (high rank) are generally more extensively cleated, it is suggested in the present work that the degree of cleating is directly responsible for the quantity of respirable-sized particles produced in the crushed product material for eastern U.S. coals. This is implied by the relationship of ash content and at least one mineral constituent (pyrite, determined from pyritic sulfur analysis) to the percentage of airborne respirable dust. To validate this hypothesis, a description is offered that is based on known coal petrography. Another key factor is the effect of air dry loss moisture in the coal seam on the breakage-induced electrostatic field of airborne dust. The air dry loss moisture factor appears to control the amount of airborne respirable dust that is liberated from the product. The resultant effect of these factors is that different percentages of coal particles smaller than 10 µm are dispersed as airborne respirable dust with a well-defined peak in the normalized airborne respirable dust for a narrow range of air dry loss moisture - ash ratios. A clear delineation of coals, based on well-known proximate analysis characteristics, that generate the most respirable dust appears to be possible. It was also shown that the dust-generating characteristics of coals could be reasonably described by both the moist fuel ratio

By Vu Van Dong

Resource estimation is the science of determining the amount and quality of a given material in the ground that has the potential to be mined at a profit. This is because during this time computers have become more widely available and more powerful and software packages have become more comprehensive and user friendly. Over the past three years The Mining Geology Company with the support from Vinacomin Group has developed the Coal Geological Modelling and Reserve Estimation ? VMG system. The VMG system enables the geological and mining engineer to start at the reserve estimation for the mine design and planning. The VMG system enables the national and international standards (NI43-101, CIM-Canada; SAMREC Code, Africa, and JORC Code, Australia) and user friendly with menu driven thereby permitting the engineer with minimal computer training to rapidly learn and utilize the system. Geological and mining data input through digitized map files and drill-holes information files stored in the database that is an integral part of the VMG system with the main function for collection, validation, and recording, storing and processing of data will include both ?primary? (observation and measurement) and ?interpreted? data. It is recommend that data be stored digitally, using a documented, standard format and a reliable storage medium that allows for easy and complete retrieval of the data. The coal reserve estimation through standard polygon methods with the increased use of these mathematical techniques (geometrical modelling, geostatistical method, least square method, ?) over the last ten years corresponds, to some degree, to a decrease in both the amount of the coal deposit mapping and, in particular, coal seam structural interpretation and modelling, and permit rapidly evaluation of coal seam and overburden quality and quantity. The understanding of the relationship between the coal mineralization of interest and the likely related complicate geological processes and structure that govern its emplacement and geometry within the geological framework is essential to the establishment of the geological controls for coal mineralization. System outputs includes: drillholes summary reports, stratigraphy, cross-sections, isopach maps, structure, contour maps, premining and post mining topography maps, and 3D perspective view on coal seam structure.

Oct 1, 2009