Search Documents

By Andre Zingano

The coal seam strength and the failure criteria that represent the behavior of the coal seam are very important for mine section and pillar design. Additionally, mine section and pillar design take into account roof and floor layers, which form the roof-pillar-floor system. Therefore, underground ground control design begins, most importantly, with rock mass characterization. Another issue is the distribution or behavior of the coal seam strength for the whole mine area. Sometimes, the coal seam strength is assumed to be the same for an entire area, but this is not true because the coal seam is heterogenic and anisotropic, and also the coal strength is affected by faults and spacing between fractures. The objective of this paper is to demonstrate the use of the methodology for geomechanics characterization to determine the strength for the Bonito coal seam, and discuss the coal seam strength distribution around the entire mine area. The intact coal strength was determined by laboratory tests that were completed during the last 17 years, including triaxial and uniaxial strength tests. It was noted that there is a strong correlation between all laboratory strength tests with 90% confidence interval. The explanation for this coal seam strength variation is the presence of the discontinuities and their variation in quantity and quality at each location in the mine area, because the coal seam rock classification and its behavior will be affected by the quantity and quality of fractures.

Jan 1, 2014

By Brian L. Quick

Problem: The National Institute for Occupational Safety and Health's [NIOSH] National Occupational Research Agenda (DHHS Publication No. 96 115) reports that approximately 50% of miners will experience hearing loss by age 50, compared to only 9% of the general population. The present investigation examines three antecedents believed to be associated with miner's use of hearing protection. Method: A posttest delayed posttest control group field research design was employed to assess antecedents toward wearing hearing protection. Results: Following the initial posttest, miners' attitudes and subjective norms were antecedents to intentions to wear hearing protection devices. Also, intentions toward wearing hearing protection predicted hearing protection behaviors. Approximately six weeks later, miners' attitudes and perceived behavioral control were each significant predictors of intentions to wear hearing protection and again, intentions were positively associated with hearing protection behaviors. Impact on Industry: Our results indicate that appeals to normative influences may be the most effective antecedent to employ when persuading coal miners to wear hearing protection. However, messages designed to impact attitudes and perceived behavioral control were also effective.

Jan 1, 2008

By H. Von Michaelis

The world is rapidly becoming more ?green? i.e. energy conscious. Since mining and mineral processing are massive energy users, the mining industry is seeking ways to reduce its energy footprint. In mining and mineral processing operations, energy is often the most expensive cost item. Comminution, i.e. grinding, is frequently the most energy-intensive step between mine and metal. High pressure grinding rolls (HPGR) are being installed in a rapidly growing number of ?hard rock? mineral processing operations. In the energy conscious cement industry, HPGR grinding has been standard practice for decades. HPGR is known to be energy-efficient; the question is how energy efficient? How can the energy efficiency of HPGR be enhanced? This paper reviews recent HPGR applications for the processing particularly of copper, gold, platinum, PGM-Ni-Cu and iron ores. HPGR technology is discussed with respect to energy efficiency. The harder the ore the greater the energy savings are likely to be. Typical energy savings of 10?20% can be expected when installing HPGR vs. a SAG mill. Wipf(2005) showed why conventional Bond Work index tests on HPGR product is likely to under-estimate the energy savings that can be achieved by installing HPGR. Energy efficiency of HPGR is, however, ore-specific. The biggest energy savings of HPGR tested thus far is 9.5 kWh/tonne claimed for Vista Gold?s Mt. Todd gold ore from Western Australia, a savings of over one-third of conventional SABC comminution energy. Several commercial scale iron-ore pellet feed plants install HPGR for fine-grinding of concentrate to increase the surface area of pellet feed in a manner that reduces overall energy consumption. Energy-consumption in comminution is, however, only part of the energy savings benefit story. HPGR typically also reduces the amount of steel lost through wear of mill liners and media. Marsden(2008) showed that when the energy that would have been consumed to produce the steel that is saved by applying HPGR is factored in, then the overall energy savings of HPGR is considerably greater. Johnson et al.(1988, 2005) tested HPGR in a flowsheet in which energy savings of around 50% can be expected if HPGR product screen oversize is recirculated to the HPGR. Innovative flowsheets have been proposed by Rule et al.(2008) and by Morley (2008) which are expected to result in significantly increased energy savings. HPGR applied in flowsheets in conjunction with coarse ore separation devices, e.g. ore sorting or DMS to remove barren waste from HPGR feed promises significantly greater energy efficiencies. Fine-grinding and ultra-fine grinding of ore or concentrates in conventional ball mills results in energy consumptions that increase exponentially with product fineness. Wipf (2009) presented a flowsheet in which he proposed the installation of HPGR ahead of the Aerosion ?Disintegrator? for ultra-fine grinding of ores and/or concentrates. This dry grinding arrangement is expected to achieve ap80 = 7 µm using up to 100 kWh/t less energy than could be achieved by wet ball milling. Using conventional comminution, an ore might require grinding to p80 = 45µm (? 325 mesh), for example, to liberate the valuable components, e.g. magnetite, from gangue, e.g. silica. Inter-particle comminution in HPGR may break some ores along grain boundaries thereby liberating valuable minerals from gangue at a much coarser particle sizes. Early magnetic separation rejection of silica gangue liberated from magnetite by HPGR at coarser grain sizes could further reduce downstream comminution energy consumption.

Jan 1, 2009

By G. J. Karabin

The Boundary Element Method of Numerical Modeling has become an increasingly popular rock mechanics -mine design tool. It has been used by the Roof Control Division, Pittsburgh Safety and Health Technology Center, MSHA, to aid in the resolution of complex ground control problems since 1985. This paper will present an overview of an evolving simulation process and details of methods utilized to generate necessary coal, rock and gob input properties. Also included is a description of a Deterioration Index System that is used to link model output to observed mine conditions and two case studies to illustrate that process.

Jan 1, 1995

By S. Mathieu, R. Mennillod-Blondin, P. Cousin, N. Valle, H. Bouzahzah, P. Marion

The gold deposit of the Lapa mine has a complex mineralogical gold state with coarse and fine native gold, aurostibite and submicroscopic gold within arsenopyrite. A specific mineralogical characterization of the refractory fraction was conducted combining various techniques such as optical microscopy, electron microscopy, electron microprobe and secondary ion mass spectrometry. In parallel, the mineral processing behaviour and the recovery of the refractory gold were studied by pressure oxidation and cyanide leaching. This paper presents the mineralogical methodology developed to characterize the refractory gold distribution within arsenopyrite. These results are presented and interpreted in order to plot gold recovery versus sulphide oxidation. The comparison of the metallurgical behaviour yields predicted from the mineralogical data and the one calculated from leaching tests shows a good agreement and allows mineralogical explanations of the gold metallurgical behaviour.

Jan 1, 2011

By Jorma Miettunen, Reijo Kalapudas, Pertti Koivistoinen

A new method for measuring the mill filling was developed by Outokumpu’s Pyhäsalmi concentrator during 1989-90. The method utilizes the power draw oscillation which is caused by the mill lifters. Each lifter bar causes a peak in the power draw and thus a continuous oscillation results. In a fixed time scale, the oscillation peaks will shift as the lifter bare hit the mill charge sooner or later depending on the volumetric filling of the mill. Thus the measuring method is based on the phase shift of the power oscillation. So far the measurement is utilized for maximizing throughput of the primary mills at Pyhäsalmi and Enonkoski concentrators and at Harjavalta slag concentrator. The paper describes the new method and the results achieved.

Jan 1, 1992

By U. K. Custred

In 1973, the United States production of marketable phosphate rock set a record in excess of 42 million tons. This production rate is expected to continue to increase, due to the growing international requirement for fertilizer, at a rate exceeding 5% per year well into 1977. This trend contrasts sharply with the reduced phosphate rock production levels of the 1966 - 1971 period. The natural consequence of this growing phosphate rock market is an evaluation of the variety of means whereby plant capacity can be most effectively increased. One approach toward increased plant production capacity is through large capacity flotation cells provided they can be successfully applied to the recovery of the relatively coarse product which is characteristic of the phosphate rock feed. This paper will summarize the results of a nine month evaluation test program, conducted at the Haynesworth Mine at Bradley, Florida in which the flotation circuit "specific capacity" (tons feed/ft.2 floor space) and "specific input power" (Hp/ton feed) were determined, and the feasibility of achieving economically acceptable concentrate grade and recovery levels was demonstrated, using large, high capacity, flotation cells.

Jan 1, 1974

By K. Izumi

Ultra-grain refinement and high strengthening of metals by accumulative roll bonding (ARB) was widely reported. However, applications of ARB to magnesium alloys were rather limited. In this study, Mg-9%Li-1%Y sheets were applied to ARB at room temperature. Six 0.5 mm thick sheets were stacked and reduced into 0.5 mm thick by four passes. The procedure was repeated up to three cycles, so that the equivalent strain of 6.2 was applied. The sheets show dual phase structure with a (hcp) and ß (bcc). Grains elongates to the rolling direction with increasing number of ARB cycles. After three cycles, fragmented a grains with average size of about 300 nm are uniformly distributed. After the first cycle, the ultimate tensile strength increases to 180 MPa from 133 MPa, while the elongation decreases, however, still high (26%). The tensile strength slightly decreases by the second cycle and does not change at the third cycle. Meanwhile the elongation increases by the second cycle and the sheets show 41% of the elongation after the third cycle.

Jan 1, 2006

By John Durkin

Field studies have been conducted in a large number of coal mines throughout the U.S. to determine the effectiveness of electromagnetic techniques in locating men trapped underground following a mine disaster. Data from these tests have been used to generate models of expected signal and noise distributions as found above mines throughout the coal fields. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results indicate an expected 45% probability of detecting a miner's signal from a depth of 1,000 ft, a depth which exceeds 903 of the coal mines within the U.S. and a 90% probability at a depth of 500 ft, a depth which exceeds 50% of the mines.

By Shuo Zhang, Wenying Liu

"In dump leaching, the efficiency of metal extraction from ores is strongly influenced by the mechanisms of fluid flow. Particle size distribution acts as a fundamental parameter in the determination of fluid flow properties in packed ore beds. In this study, we investigated the particle size distribution in dump leaching by using image analysis technique. The results showed that the particles in the dump varied from smaller than 2 cm to larger than 200 cm in diameter. P80 was calculated to be 200 cm, which was significantly higher than the historical data used by the operation. P25, P50 and P80 were found to increase non-linearly with increasing depth towards the toe of the dump, suggesting the segregation of fine and coarse particles. The image analysis results were verified by applying the rock fragmentation models. The model with the Swebrec function was found to be in better agreement with the image analysis results. Future research will investigate the effect of particle size distribution on the behaviour of fluid flow.INTRODUCTION Fluid flow plays an essential role in the extraction of valuable metals using heap/dump leaching (Amos et al., 2009). The rates of the chemical leaching reactions and microbial activities determine metal concentrations in the leachates and therefore the efficiency of the metal extraction. The reaction rates are influenced by two fundamental processes: transport phenomenon and reaction kinetics (Bouffard & Dixon, 2001). The transport phenomenon refers to the percolation of fluids through channels and pores in a packed ore bed, which carries lixiviants and reaction products to/from ore surfaces by convection and diffusion. The percolation rate of the leaching solution is determined by the hydraulic conductivity of the packed ore bed, which is a function of the permeability and the degree of saturation (Guzman et al., 2008). Permeability, an intrinsic property of a packed ore bed, is strongly influenced by the particle size distribution of the ore grains (Bouffard & Dixon, 2001). Hence, the objective of this study was to investigate the particle size distribution in dump leaching."

Jan 1, 2017

By W. I. Nelson

This paper which describes the milling practice of the Engels Copper Mining Co., is one of a series on milling methods being prepared for and published by the United States Bureau of Mines. ACKNOWLEDGMENTS Acknowledgment is made of the assistance rendered by J. Casagrande, mill foreman of the Engels concentrator, in collecting much of the data presented in this paper.

Jan 1, 1932

By J. A. Ruppert, P. M. Sullivan

A study was made of filtration techniques for recovering the major part of the tin contained in iron - tin alloys known as hardhead . Special smallscale filtering apparatus and a three - stage cyclic process were developed . Eighty- seven percent of the tin contained in an alloy of 82 percent tin and 17 percent iron was recovered as pure metal by pressing at 975° C followed by a second pressing at 800 ° C and a final filtering at 250 ° C. Small amounts of Sb , Cu , and Fe impurities were removed by adding Al to the molten product and performing another filtration at 250 ° C.

Jan 1, 1964

By Vivek Samu, Murthy Guddati

A new method called Effective Dispersion Analysis of Reflections (EDAR) was recently developed to effectively analyze the dispersive waves generated from lateral impact to piles. This paper presents the results of nondestructive length estimation of existing piles through EDAR. EDAR provides a new visualization method for analyzing wave reflections by transforming the response into the frequency domain thus eliminating the need to perform difficult peak picking in the time domain. In addition to being able to analyze dispersive waves, EDAR also incorporates the effects of radiation damping due to the surrounding soil leading to more accurate length estimates. Concrete filled steel tubes of different embedment depths were tested both in laboratory and field conditions. Length estimates obtained were within 10% error margins after careful analysis accounting for the presence of soil effects and effects from pile top reflection.

By T. Xu

"The CTL-500 centrifugal extraction machine, which was independently developed by Baotou Shibo Rare Earth Extraction & Equipment Co., Ltd., is presented in this article. The machine is based on centrifugal extraction principle and has been used in P507-HCl-RECl3 extraction system. Automatic control has been utilized in the system. In this paper, a comparison is made between centrifugal extraction and conventional mixer-settler extraction and satisfactory results are shown. INTRODUCTIONCentrifugal extraction is a fast and efficient liquid-liquid extraction method. The process includes solute transfer and separation of the two liquid phases. In the CTL-500 machine, the organic and aqueous phases individually enter a lower mixing chamber in certain proportions and are mixed and dispersed and solute thereby transferred from one phase to the other. The mixed phases pass into a rotating drum and the two liquid phases are separated under centrifugal force. As it flows upward, the aqueous phase, which has a higher specific gravity, flows away from the rotating drum centre towards the drum wall and the organic phase flows towards the drum center. The two liquid phases enter into collection chambers through independent weir plates and are discharged from the machine.The centrifugal extraction machine has been widely used in liquid-liquid separation, either without solid or with small quantities of solids (Chen, Zhang, Zhuo, Chen & Li, 2008; Duan, Jing, Zhu & Chen, 2007; Duan, Zhou & Zhou, 2006). Examples of the use of the centrifugal contactor include the separation of water from crude oil, treatment of heavy oil and diesel to eliminate water and salt; the extraction of penicillin, garlic oil, malathion, and interferon; the hydrometallurgy recovery of nickel, copper and uranium; extraction of edible oil, spice, refined oil and food color; treatment and recycle of print and dyeing wastes; treatment of hydroxybenzene-contaminated sewage by multistage extraction and separation of water from oil in ship sewage."

Jan 1, 2012

By P. Lostritto, G. E. Agar, G. Labonte, M. Cherevaty

"A locked cycle flotation test was done on a sample from the ovoid portion of the Voisey 's Bay copper-nickel sulphide ore. The chemical conditions for this test were generated by prior independent testing. In this test work the time in each of the five separation stages was optimized prior to executing the locked cycle test. A numerical simulation of the continuous circuit material balance was done prior to the locked cycle test. The test results were not fully satisfactory because the flotation of pyrrhotite in the bulk rougher and cleaner stages was not consistent. The preliminary indication was that the samples had oxidized to varying degrees during storage.INTRODUCTIONINCO has performed batch laboratory flotation testing on ore from Voisey's Bay which is a mixture of chalcopyrite, pentlandite and pyrrhotite. Earlier, Lakefield Research was contracted by Diamond Field Resources to test the ""flotability"" of the ore, which included a pilot plant trial. INCO's J. Roy Gordon Research Laboratory has repeated many of the batch tests that Lakefield did to verify their results. Based on their own work, INCO has modified the circuit proposed by Lakefield Research. The modified circuit is based on batch test work, but no locked cycle test (LCT) was done. It is believed that this circuit will produce a copper concentrate at 29-30% copper and a primary nickel concentrate at 15-20% with recoveries of 80% or above.For several years the University of Toronto has been working with INCO to provide ""hands on"" experience for undergraduate students as an Industrial Research Project (IRP). This year, the objective for IRP was to optimize the time for each of the five separation stages for the Voisey's Bay ore then to numerically and experimentally simulate the material balance for a continuous circuit."

Jan 1, 1998

Traditional mineral processing techniques are more and more difficult to recover the increasingly low grade phosphate ores today. Although bioleaching method has been attempted to process low grade ores in hydrometallurgical field due to economical and environmental reason, it has been hardly used in leaching phosphate ore at home and abroad. Strains of Acidithiobacillus thiooxidans and Acidithiobacillus ferrooxidans were collected and separated from the acid drainage of a coal mine in Anhui province of China. Ultraviolet irradiation and Microwave inducement were applied to the bacterial cultivation process to produce strains of Acidithiobacillus thiooxidans and Acidithi-obacillus ferrooxidans able to tolerate extremely low pH conditions and generate sulphuric acid by oxidizing elemental sulfur or sulphide and the mutagenesis can achieve higher leaching rate. The bioleaching result will improve more by the addition of Tween series surfactants.

Jan 1, 2014

By R. Hogg

Experimental studies of the axial distribution of particles along dry ball mills are described. The results, for mills ranging in diameter from about 10 cm to 1 meter and operated in both the batch and continuous modes, indicate a consistent pattern of significant migration of particles away from the ends of the mill. In some, but less frequent, cases axial migration of the grinding media is also observed. Analysis of the data suggests that particle migration results from end-effects which extend for a distance of about one mill diameter along its length. End-wall roughness appears to play a significant role in the particle migration phenomenon. Media migration is generally associated with continuous mills operating at relatively high powder flow rates.

Jan 1, 1994

By Oscar Perales Perez, Atsuo Kasuya, Kazuyuki Tohji, Yoshiaki Umetsu

"The removal of iron and various heavy-metal ions by their incorporation into stable ferrite-type precipitates at 25°C is a promising alternative to clean up large volumes of polluted aqueous effluents. Our research work investigated the conditions to produce magnetite and various M-bearing ferrites (where M: Zn, Cu, Co, Ni, Cd, etc.) directly from aqueous solutions at 25°C by simultaneous control of the oxidizing conditions and pH. The formation of the solids was followed by monit9ring the oxidation-reduction potential (ORP) and rate of proton release during the aerial oxidation of the suspensions at constant pH (contact stage). Only mildly oxidizing conditions, represented by ORP values between -110 mV and -150 mV and a moderate oxidation rate of Fe(II) species were conducive to well-crystallized ferrites at ambient temperature.' It was also found that increasing the Fe/M mole ratio in starting· solutions enhanced the stability ·of the M-bearing ferrites at ambient temperature. When the formation of the ferrite was incomplete, aging of the sludges in their mother liquors at 25°C promoted the crystallinity of the precipitates. The mentioned conditions ·favored the suitable progress of the ferrite-forming reaction involving the oxidation of Fe(II) entities, subsequent hydrolysis of produced Fe(III) species and dehydration of the intermediate:· Furthermore,· the ferrite formation at· low temperature permits the elimination of iron and co-existing heavy metal ions to sufficiently low concentration.In tum, the characterization of the precipitates evidenced their magnetic nature (room-temperature saturation magnetization above 60 emu/g) as well as the effective incorporation of target metal ions into the ferrite structure."

Jan 1, 2000

By F. Calizaya, M. G. Nelson

This paper presents a summary of basic requirements for the design, installation and operation of booster fans in coal mines, especially in deep and/or extensive mines. It includes a brief description of the major steps that should be followed to ensure that these units are used in coal mines safely and efficiently. The guidelines were prepared based on the standards and regulations adopted by two prominent coal mining countries, the best practices developed by the mining industry, and the applicable standards used in the United States for the fail-safe operation of main fans.

Jan 1, 2015

By M Spagnolo, M Ashley, D, L Reemeyer

PasmincoÆs Century Concentrator in North West Queensland commenced operations in November 1999. The nameplate production capacity of 500 000 tpa of zinc metal production in concentrate was achieved in August 2002. Completion of the production ramp up was successful due to the culmination of a number of initiatives throughout 2001 and 2002. Mine to mill interaction to understand and eliminate head grade related bottlenecks affecting Concentrator production and reduce feed variation. Grinding circuit process development û operating and process control strategies to improve stability and reduce grind size to support zinc recovery. Pumping upgrades to control spillage in ultrafine zinc flotation Low density zinc flotation strategy û to improve silica-sphalerite separation to improve zinc recovery while maintaining acceptable silica in final concentrate. Flotation circuit process development û froth crowders, froth cameras and reagent control strategies to improve primary zinc flotation performance. Review and implementation of longer campaigns between planned shutdowns to improve availability. Team reorganisation û to improve setting and implementation of metallurgical strategies. This paper describes these initiatives and their contribution in achieving the production target. It also notes the ball mill motor failures that delayed the successful achievement of the ramp up, and CenturyÆs response to minimise the production impact. The paper also outlines the capital improvement program that was implemented to improve zinc recovery to design 82.5 per cent recovery once the production rate had been achieved.

Jan 1, 2003