Search Documents

By R. V. Ramani, J. Qin

"In this paper, the results of a research study on airborne dust transport in a full scale simulated longwall face are presented. The simulated longwall face was set up in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines to conduct experiments under controlled conditions. The controlled parameters in the experiments were the dust dispersion rate, dust size distribution, density of the dust, air velocity, and the rate of travel of the dust generating source. The analyses of the experimental results on mass concentrations, particle size distributions, and real-time respirable dust concentrations are discussed. There are definite spatio-temporal trends between the location of the shearer, the concentration at any location in the face, and the dust generation rates. The size-consist and density characteristics of the source dust, the air velocity in the face, and the air leakage into the gobs all affect the concentration. INTRODUCTIONA detailed experimental study on the characteristics of longwall dust cloud in operating longwall faces has been reported by Ramani, Qin, and Jankowski (1991). The study indicated that there are several important factors whose effects on dust transport in longwall faces need to be further investigated. In an operating longwall face, the effect of these parameters could not be easily isolated as control over the affecting parameters is not readily possible. In a simulated longwall face, however, these parameters can be controlled. Therefore, as a follow-up to the field study, a series of controlled experiments were conducted in a full scale simulated longwall face in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines [Qin, 1992]. Specific aspects which were addressed during the experimental design phase included determining the types of samples to be collected, selecting proper instruments to collect these samples, and developing detailed sampling and time-study plans to correlate the dust concentrations with face activities. Two types of dust--anthracite and bituminous--were used. Dust dispersion rate into the air as well as the source dust particle size distribution were documented. Control was exercised over both air velocity at the face and air leakage along the longwall face. During experiments, the dust source was moved to simulate the shearer movement at operating longwall faces. Detailed descriptions of the design of experiments, experimental results, and data analyses follow in the subsequent sections."

Dec 1, 1996

By J. D. Robertson

An in situ water sampling device has been developed to measure biologically-available or “labile” metals in natural waters and effluents. The active mechanism involves the use of a polyacrylamide gel layer to quantitatively control metal transfer to a trace-metal-adsorbing, gel-imbedded resin. Because the resin only adsorbs free metal ions (the gel sampler methodology is a kinetic speciation technique), and because metal bioavailability is related to the free-ion activity, the device provides a direct measure of the biological-availability of metals in the environment sampled. The prototype consists of a layer of ion-permeable polyacrylamide gel which separates the solution to be sampled from an ion exchange resin. Because approximately 90% of the polyacrylamide gel is water, mass transport through the gel is diffusion-controlled, and is therefore well defined. Metal ions are rapidly bound by the resin, creating a steep concentration gradient in the gel. The amount of labile trace metal that accumulates on the resin can be related directly to the concentration of the metal in solution, the exposure time and the molecular diffusion coefficient of the labile species. In addition, the passive nature of this device affords it the potential to address many of the limitations presented by conventional sampling methods, such as sample contamination introduced during collection or filtration and changes in trace metal speciation prior to analysis. Laboratory studies and limited field trials indicate that the sampler behaves as anticipated and illustrate that biologically- available metal concentrations in many environments are a small fraction of the total concentrations and often significantly less than the dissolved concentration. The implications of this on regulatory criteria are discussed. Additional field trials and correlation with bioassays are currently underway.

Jan 1, 2000

By Runsheng Xu, Haiyang Wang, Pengcheng Zhang, Tengfei Song

Semi coke, a byproduct in the chemical industry, is a new fuel for blast furnace injection in China. In this study, semi coke and bitumite were milled into different size, ranged from 0.147mm to under 0.074mm. The content of volatile matter and ash, which affect the combustibility of semi coke, were measured using muffle furnace. The mixture, in which the proportion of coal in different sizes changed, was blend by semi coke and bitumite with different size. Activation energy calculation and the comprehensive combustion characteristic index of all kinds of blends was also discussed. The result obtained by Thermogravimetry –Derivative Thermogravimetry curves indicates that the smaller the size of mixture is, the lower for the characteristic temperature, and the better for its combustibility, Semi coke can be a substitute for anthracite in blast furnace injection.

Jan 1, 2015

MORE than 5000 miners and suppliers descended upon Denver to make the American Mining Congress' four-day metal mining show one of the most extravagant equipment displays ever assembled in one place at one time. The most recent developments in equipment for mining, milling, and processing ore were shown by the 146 exhibitors at Denver's new City Auditorium which covers 57,000 sq ft of floor space. Other displays were placed in the open air opposite the auditorium site. Registration desks were opened Sunday, Sept. 21. A field trip to the Colorado School of Mines at Golden was the featured activity of the day. Official opening of the show took place on Monday, and presided over by Howard I. Young, president of American Zinc, Lead & Smelting Co.; Otto Herres, vice president, Combined Metals Reduction Co.; William J. Coulter, vice president, Climax Molybdenum Co.; Charles B. Stainback, Westinghouse Electric Corp.; and Merrill E. Shoup, president, Golden Cycle Corp. Convention welcoming addresses were delivered by a representative of Mayor James Q. Newton, of Denver, and Gov. Daniel V. Thorton of Colorado. Following the formal opening ceremonies a round table discussion dealt with the "Paley Commission Report" formally called Resources for Freedom. Participating in the panel were: Arthur H. Bunker and George R. Brown, members of the Paley commission; H. I. Young, president of the American Mining Congress; Horace M. Albright, president of U. S. Potash Co.; Evan Just, vice president, Cyprus Mines Corp.; Donald H. McLaughlin, president, Homestake Mining Co.; E. H. Snyder, president Combined Metals Reduction Co.; Simon D. Strauss, vice president, American Smelting & Refining Co.; Sen. H. C. Dworshak (R.-Idaho) ; Ira B. Joralemon, consulting engineer; Jess Larson, De fense Materials Procurement Agency; and Andrew Fletcher, president of St. Joseph Lead Co. The panel discussed the report for six hours, adding a great deal of information to the already voluminous amount which has been gathered concerning it. Three objections to the report frequently mentioned were: 1-the multilateral contract; 2-international buffer stocks; 3-international buffer stocks combined with limited quota arrangements. Points on which the panel commended the report were its recommendations for acceleration of topographic and geologic mapping of the United States and Alaska; recognition of the principle of percentage depletion for metals and minerals; and advocation of removal of the present limitations on the expensing of exploration costs applicable to minerals. Technical sessions were held throughout the four days of the meeting. Included in the program were: Progress in Mechanication; Small Mines; Public Lands; Open Pit Mining; Manpower-Labor Relations; Shaft Sinking; Roof Support; Taxation, Gold, Silver and Monetary Policy; Advances in Mill Practices; Special Conference on Strategic Materials; Uranium Mining-Atomic Energy; Prospecting and Exploration; New Metallurgical Processes; and Rock Breaking. About 45 papers and several panels were presented during technical sessions. Formal and informal social functions consumed the remaining time of the convention. Three locations were needed to handle the huge throng attending the Mining Jamboree Monday evening. The only other sponsored social function took place Thursday evening. A great many informal gatherings, chiefly convivial, were held in manufacturers' courtesy rooms-called wet stopes. Field trips included Cripple Creek, Pueblo, Climax -Leadville-Gilman, Colorado Plateau-Grand

Jan 1, 1952

By Samuel Filgueiras Rodrigues, Sebastião Raimundo de Jesus Belém leitão Filho, Gedeon Silva Reis, Eden Santos Silva

Nesse trabalho estudou-se o retardo na cinética de amaciamento estático do aço inoxidável austenitico ASTM F-1586 (ISO 5832-9) usado na confecção de implantes ortopédicos, por meio de ensaios de torção a quente isotérmico em duplo passe. Inicialmente as amostras foram aquecidas por indução até a temperatura de 1250 oC e mantidas por 300 s para solubilização, em seguida resfriadas até a temperatura de deformação (Tdef), que variou de 1000 a 1200 oC, com passes de deformações de ε1 = ε2 = 0,30, taxa de deformação de 1,0 s-1 e tempo entre passes (tp) variando entre 0,1 – 1800 s, simulando um processo de forjamento a quente industrial de um dispositivo ortopédico. Os resultados da simulação física do processamento termomecânico indicaram que 60 % do amaciamento dá-se por recuperação estática (SRV), com moderado valor de energia de falha de empilhamento (γEFE ~ 69 mJ/m2) do aço e tempo de encubação pra iniciar a recristalização estática (SRX) maior que 10 s abaixo de 1100 oC com formação de patamares nas curvas de amaciamento Xs vs tp, indicando atraso na cinética de recristalização estática (SRX) resultante do efeito dos precipitados da fase Z (NbCrN) induzidos por deformação nos contornos dos grãos austeniticos.

Nov 18, 2019

By G. M. Scamans

In the past ten years there has been considerable penetration of aluminum automotive body sheet (ABS) into automotive structures. The exponential increase in demand is resulting in major investments in heat treatment and finishing capacity across the globe. Line speed and tonnage throughput is limited by the continuous heat treatment (CHT) floater furnace rather than the cleaning and pretreatment section where electrolytic treatments that offer higher line speeds should come into favour and roll coating of pretreatment should predominate. The capacity limiting surface texturing pass will either be eliminated or moved to the finishing line or a dedicated mill. The key to making aluminum both embedded carbon and cost competitive with steel for more and more affordable classes of vehicles lies in recycling of both prompt scrap and, in the longer term, end of life vehicle scrap. For the first time scrap separation technology is available that can compete effectively with hand sorting and can sort aluminum shredded vehicle scrap into wrought and cast alloys and then into individual alloy groups. The challenge is to use more end of life scrap in alloy formulation whilst at the same time extending the property range in terms of both strength and formability.

Jan 1, 2015

By G. M. Scamans

In the past ten years there has been considerable penetration of aluminum automotive body sheet (ABS) into automotive structures. The exponential increase in demand is resulting in major investments in heat treatment and finishing capacity across the globe. Line speed and tonnage throughput is limited by the continuous heat treatment (CHT) floater furnace rather than the cleaning and pretreatment section where electrolytic treatments that offer higher line speeds should come into favour and roll coating of pretreatment should predominate. The capacity limiting surface texturing pass will either be eliminated or moved to the finishing line or a dedicated mill. The key to making aluminum both embedded carbon and cost competitive with steel for more and more affordable classes of vehicles lies in recycling of both prompt scrap and, in the longer term, end of life vehicle scrap. For the first time scrap separation technology is available that can compete effectively with hand sorting and can sort aluminum shredded vehicle scrap into wrought and cast alloys and then into individual alloy groups. The challenge is to use more end of life scrap in alloy formulation whilst at the same time extending the property range in terms of both strength and formability.

Jan 1, 2015

By Athena C. Denivo, Pablo V. Lopez, Sissy Nikolaou, Alfred H. Brand, Ahmad Rahimian, Rudivien G. Josef

"The United States Tennis Association (USTA) Billie Jean King National Tennis Center (BJKNTC) site is located in the northeastern portion of the Flushing Meadows Corona Park area of Queens, N.Y. The site occupies some of the most difficult subsurface conditions for construction in the New York City (NYC) metropolitan area, with unique challenges from geotechnical, seismic and foundation design perspectives.At the USTA site, Paleozoic crystalline bedrock is found at a depth of roughly 300 to 400 ft (90 to 120 m) below grade. The geologic history of the site is complicated, starting from the early Pleistocene, when the ancient Hudson River temporarily changed course, flowing across Queens enroute to the Atlantic. It eventually carved a deep valley through the Cretaceous soils, in some places all the way down to bedrock. A series of glaciers advanced and retreated across the region during the Pleistocene times, filling the deep valley with layers of assorted glacial soils. At its southern edge, the last major glacier to flow across the region built up a ridge at the southern tip of Flushing Meadows known as the Harbor Hill terminal moraine. This ridge blocked the valley forming a dam, so as ice started melting away the valley filled up with a lake fed by glacial meltwater. Layers of clean outwash sand and varved silt and clay filled the glacial lake. The ice did not retreat in a steady manner, instead periodically readvancing over the previously deposited soil in the lake, then retreating far enough to let the lake drain temporarily into Long Island Sound, before readvancing again.As a result of this repeated sequence of retreat, advance, retreat, etc., there are places where a “crust” of desiccated soil formed when the lake drained, and areas with interlayers of outwash sand where ice readvanced into the lake. When the ice melted north of Long Island Sound, the glacial lake filling Flushing Meadows drained forming Flushing Creek. During the Holocene (roughly the last 11,000 years), as ice melted further away and sea-level rose, low lying areas filled with river sands and marine clays, along with coastal marsh deposits. Table 1 lists the soil design properties on site and Figure 1 exhibits the geologic section across the site."

Jan 1, 2015

By Breno Totti Maia, Luiza Siqueira de Magalhães, Vanessa Rodrigues de Medeiros Santos, Inamara Amanda Souza Santos, Brenda Caroline Gurgel, Aline Lima da Silva

O sucesso da utilização do método de reparo/prevenção de refratários de convertedores LD chamado Slag Splashing tem relação com as propriedades físico-químicas da escória, em especial a sua viscosidade. Através de uma simulação termodinâmica feita no software FactSage que tomou como base a equação de Einstein-Roscoe utilizando uma escória de composição representativa de uma escória industrial, junto de uma simulação a frio utilizando soluções representando escórias com variadas frações sólidas, foi possível correlacionar a viscosidade do modelo a frio, avaliando a possibilidade de transposição de resultados desse modelo para a prática industrial em escórias com frações sólidas de até 20%, sendo que acima desse valor um modelo mais assertivo deve ser restabelecido. Por simulação física a frio em um modelo de conversor de escala de 1/10 em relação aos conversores de 340 toneladas da Ternium Brasil, utilizando soluções representativas de escórias industriais com frações sólidas de 10 a 40%, avaliou-se a influência da viscosidade na intensidade na projeção de escória durante o processo do Slag Splashing, deixando claro o efeito da fluidez ou da alta viscosidade na altura, localização e qualidade das projeções.

Oct 1, 2019

By C. W. Dunham

FOR discharging and diffusing the gases from the reverberatory furnaces and converters the Morenci Reduction Works has been provided with one of the largest reinforced concrete chimneys ever built. It is 612 ft. high from the bottom of the foundation to the cap at the top, and has a minimum diameter of 24 ft. inside the lining near the top and 38 ft. 10 in. at the bottom. Its estimated capacity, at the elevation of 4338 ft. above sea level, is about 1,000,000 cu.ft. of gas per minute at a temperature of 500° F. and an atmospheric temperature of 90°. Under these conditions the draft will be at least 3 in. of water at the flue inlet. The gases enter the chimney through a steel balloon flue 33 ft. high and 15 ft. wide, the bottom of which is 19 ft. above the ground.

Jan 1, 1942

By Maurice A. Roche

Introduction Most of the Flin Flon ore-body, like many others in northern Canada, was covered by water. The original discovery was made where the ore-body outcropped on a strip of land jutting out into Flin Flon lake. The outcrop could be traced for a distance of 600 feet across the strip of land, but disappeared under the lake on both sides of the peninsula. Following the discovery or location of the property, in 1915, and subsequent to its examination by the H.P. Whitney interests in 1925, an extensive diamond-drilling programme was completed, which proved the existence of an ore-body at least 2,600 feet long and 900 feet deep. In plan, the central part of the ore-body at surface attains an overall width of about 450 feet; including waste horses, and gradually becoming narrower to the south. To the north, it stretches out as a much narrower tongue. The main body is a solid sulphide ore containing gold, silver, copper, and zinc. Adjacent to, and on the footwall side of, the solid sulphide ore-body, there are considerable widths of talcy disseminated copper ore, particularly in the upper 300 feet of the deposit, where the maximum widths occur. The ore-body occurs in a greenstone area, the rock being quite hard on the hanging-wall side, with the footwall schisted, talcy, and much softer. The greater part of the ore-body was overlain by 12 to 15 feet of water and from 15 to 90 feet of mud and clay, this material requiring eventual removal, regardless of the system of mining adopted. The total of mud and clay overburden was estimated at 1,000,000 tons. After considerable study, it was decided to mine the upper 300 feet of the ore-body by open-pit methods; the balance of the ore to be recovered by underground mining . The present paper gives an account of the methods adopted in both operations, and of the problems encountered.

Jan 1, 1935

By S. Thibeault, P. Filiatreault, B. Straight, D. Castendyk, L. Cameron

"Unmanned aerial vehicles (UAV), or drones, capable of collecting and retrieving water samples from pit lakes, tailings ponds and other mine water basins will revolutionize environmental programs by lowering sampling costs and reducing safety related risks. Costs typically include a boat and associated equipment, boat transportation, road maintenance, water safety devices, water safety training, and additional staff. Typically, the total cost can exceed $20,000 USD per sampling event (excluding lab analyses). Hazards include potential for drowning, unstable pit walls, and unconsolidated sediment surrounding tailings ponds. Hatch has developed a novel device for aerial drones which currently enables the collection of water samples from depths up to 390 ft (119 m). This system only requires a pilot, a sample technician, and a safe operations point overlooking the water body. Hatch anticipates this will reduce monitoring cost by at least 50% while improving safety, reducing staffing requirements and accelerating data acquisition. This manuscript demonstrates profiling and sample collection from a 95 ft (29 m) deep reservoir and a 377 ft (115 m) deep pit lake, and highlights the potential of this emerging technology. INTRODUCTION Working on or near water at active, closed, or abandoned mine sites is inherently dangerous. Between 1996 and 1999, the United States Mine Safety and Health Administration (MSHA) reported 17 fatalities involving drowning at US metal, non-metal, and coal mines (MSHA, 2000). Open pit mines which fill with water following mine closure, called pit lakes, present numerous risks to environmental monitoring teams including drowning, hypothermia, falls to the ground from the top of high walls, and rock avalanches resulting from steep, unstable pit walls. Some pit lakes are simply not easily accessible for ongoing monitoring. However, the routine collection of water samples from the entire water column on at least an annual basis is required to monitor the evolution of water quality over time, to verify the accuracy of numerical predictions, and to manage lake water chemistry in order to produce “treatable” influent to water treatment plants, and ultimately, produce acceptable site discharge water quality. As a product of these risks and the need for water sample, mining companies spend considerable expense on pit lake safety as part of monitoring. This includes training personnel for “on water” duties and hazards, purchasing or hiring specialized equipment and personnel (such as boats, boat operators, personal floatation devices, and mustang suits), stabilizing pit walls and maintaining safe access roads to the lake surface, employing spotters with direct communication to emergency medical services to watch sampling activities (because cell phones and radio signals can be blocked by pit walls), and utilizing redundancy to prepare for unexpected incidents and accidents. For example, one Canadian mining company requires pit lake water samplers to hold Marine Emergency Duties (MED) training to ensure the entire boat crew is sufficient and competent for the safe operation of the vessel, and uses three boats for water sampling: two on the water at all times, and one on the shoreline, ready to deploy. The costs of these safety mechanisms greatly adds to the overall expense associated with pit lake sampling. Consequently, environmental programs may need to reduce the frequency of pit lake sampling in order to keep monitoring programs within an acceptable budget"

Jan 1, 2017

By João Paulo Melo Silva

No beneficiamento de itabiritos pobres (%Fe˜44,0) um dos principais desafios para as usinas de tratamento é a produção de concentrado dentro das especificações de qualidade e com menor custo. Nas usinas de beneficiamento a moagem é a operação unitária com o maior custo. Além disso, a moagem secundária é a operação unitária na qual a granulometria do concentrado é adequada às especificações para a etapa de flotação cleaner e para o transporte em mineroduto. Dessa forma, o aumento da eficiência energética no circuito de remoagem permite reduzir os custos e aumentar a eficiência do circuito de flotação cleaner. Amostragens de rotina e testes de bancada realizados com amostras coletadas no concentrador I indicaram oportunidade de aumentar a eficiência energética (kWh/t) da remoagem e reduzir a granulometria na alimentação da flotação. Com esse objetivo, foram realizadas alterações no circuito de remoagem do pré-concentrado da flotação mecânica do concentrador I da Samarco. Essas alterações consistiram em moer todo o pré-concentrado em circuito fechado reverso e não mais em dois estágios, sendo um em circuito aberto e outro em circuito fechado. Essas alterações realizadas no circuito permitiram aumentar a eficiência energética do circuito de remoagem, reduzir o consumo energético em 9,3% e adequar as granulometria e grau de liberação para a etapa subsequente de flotação.

Aug 16, 2017

By H. R. Manouchehri

Sustainable development requires the optimal use of natural resources and recycling of the wastes. In fact recycling is the final productive use of obsoletes. ELVs, obsolete appliances and industrial wastes have become important resources for production of iron and steels, non-ferrous metals, and composites. Within shredding plants, these obsoletes are firstly shredded to the pieces and then processed to recycle different materials, especially ferrous and non-ferrous metals for metallurgy. Traditional and new developed mineral processing technologies are nowadays used for recycling different materials from waste effluents. Shredding and separating plants are currently recycle the wastes by make use of different technologies to mainly produce raw material for metallurgical application. However, other non-ferrous components are also treated for energy conservation and protecting environment. Currently, recovery in shredding and recycling plants maximises to 75% and about 25% of the feed is land-filled. However, recycling rate must be increased in due to the economical, environ-mental and social concerns. A comprehensive study for recycling, with especial focus on ferrous metal recovery, was sup-ported by Swedish Environmental Agency (MISTRA) to look at possibilities to increase the recycling rate and to reduce the amount of disposal. Part of this study was dedicated to study the shred-ding plant facilities and to look for possibilities to improve the quality and quantity of the shredding product streams. The aims were to improve the quality of ferrous scrap (apparent density > 0.9 and Cu<0.25%) for iron and steel production as well as having better quality for non-ferrous metals through the recycling schema, and finally to treat the shredder residue (SR) to recover metals and plastics to reduce the disposals. This paper summarises the results of sampling and conducting separation tests for improving the recovery of the ferrous and non-ferrous metals. The results indicated to be possible to obtain high quality ferrous scrap at recovery of 88%. However, the total recovery for metal scrap has reached 93%. Furthermore, test results on fine, P< 8mm, shredding residue (SR) showed promising prospect in recovery of metals and protecting environment by physical separation, i.e. electrical separation technique.

Jan 1, 2014

By Thomas M. Barczak

This Bureau of Mines report describes research on developing technology to utilize shields as roof load monitors. Three-dimensional equations of static quilibrium are presented for a generic two-legged long-wall shield. The equations are presented in the most general form, assuming a force and moment vector at each reaction by rigid-body analysis of the shield mechanics. The resulting system of equations was found to be indeterminate to a very high degree. A three-dimensional solution to measurement of the resultant reaction on the canopy by the strata activity and shield response required the elimination of several forces or moments that were thought to be nonparticipating or to not significantly affect overall shield mechanics. Required measurements for solution of the equilibrium equations were leg, canopy capsule, and lemniscate link forces. Two-dimensional analysis, which considered forces acting only in the roof-to-floor and face-to-waste plane, was also provided by reduction of the three-dimensional equations~

Jan 1, 1987

By Eric Klaffenbach

Valorization of slag from metallurgical industrial processes becomes ever more important as this may help optimizing and reducing the use of natural resources such as rock and sand. In view of this objective, metallurgical processes have to be analyzed in order to modify the slag composition so that it will meet the expected requirements of potential users of these resources. This paper gives the results of a thermodynamic analysis of the flash smelting process to understand the impact of operational parameters on slag chemistry and elemental partitioning in the process. It is shown that an increase of the matte grade and temperature leads to higher deportment of Pb, Zn and As to the slag. With increasing matte grade the volatilization of these elements decreases. Furthermore, the results indicate an increasing solubility of Cu and S in slag at higher temperatures.

By Edelink Efrain Tinoco Falero

Na indústria siderúrgica integrada, geram-se vários tipos de coprodutos, dentre estes escoria granulada de alto forno, os pós de aciaria extraídos nos sistemas de despoeiramento a úmido e a seco do conversor LD e o pó de coletor de alto forno. Em relação aos pós, são principalmente portadores de unidades de ferro e carbono, podendo conter também zinco, o que os tornam alvos de estudos e inovações que buscam recuperar ou reciclar estes elementos. No presente estudo foram concebidos briquetes autorredutores usando os pós finos-F e grossos -G, oriundos de um sistema de despoeiramento a seco de aciaria LD, nas proporções percentuais, F – G, de 50-50 e 70-30, misturados com pó de coletor de alto forno. Utilizando como aglomerante o cimento ARI, foram avaliadas as resistências à compressão dos briquetes em diferentes tempos de cura e determinadas suas metalizações nas temperaturas de 1100°C e 1150°C, em tempos que se estenderam até 45 minutos. Adicionalmente, as capacidades dos briquetes de alterarem a temperatura do aço liquido quando adicionados ao banho, foram avaliadas utilizando-se o balanço térmico do sistema briquete-aço liquido, bem como considerados os potenciais de oxidação do processo e o estabelecimento de um sequenciamento termodinâmico para as reações. Os resultados mostraram que os aglomerados autorredutores possuem alta capacidade refrigerante quando adicionados ao aço liquido, o que os enquadra como possíveis materiais alternativos à sucata e pelotas no controle da temperatura do aço nos convertedores LD. Além disso, a alta cinética de metalização do Fe mostrou ser também viável o uso dos briquetes autorredutores na recuperação do metal contido nos resíduos.

Oct 30, 2017

In connection with tin strategic minerals investigations of the Bureau of Mines and the Geological Survey under authority of the Strategic Materials Act (Public 117, 76th Cong., 1st sess.) a study is being made of tin deposits in the United States in an effort to improve the situation with respect to domestic supplies. These studies include sampling and exploration of some of the larger deposits with the objective of establishing emergency reserves, if possible to do so. Two exploration projects have been completed, and the over-all results obtained are set forth in this progress report. RESOURCES Tin was first discovered on this continent in 100 in the Temescal Mountains of what is now southern California. In the ensuing century, occurrences of tin have been reported in no less than 17 States and Alaska. Although most of these are of scientific interest only, tin-bearing veins and placers in California, Alabama, North and South Carolina, Virginia, South Dakota, Wyoming, Texas, New Mexico, and Alaska have been extensively explored, and largo sums of money have been expended in recurring attempts to exploit them.

Jan 1, 1941

By D Hunter

A production information management system (PIMS) was recently implemented at Queensland NickelÆs Yabulu Refinery. Although a strong business case was developed to justify the significant investment in PIMS some potential beneficiaries remained sceptical of the anticipated benefits. The decision to install PIMS was justified as the on-line availability of continuous production data enabled the optimisation of some crucial operations resulting in significant cost savings, improved throughput and final product quality. Furthermore the rapid access to extended historical data has allowed the cause of repeated failure of equipment to be determined. The investment is expected to pay for itself within two years and has already contributed towards significant savings. This paper focuses on some of the diverse production improvements gained and compares the anticipated benefits in the business case to those achieved. A brief outline of the phased implementation of the OSIsoft PI data historian and complementary client software at Yabulu is included, along with details of the lessons learned.

Jan 1, 2003

By R. J. T. Charles

Introduction An apparatus that will measure the surface area of a few of the simple minerals with a high degree of accuracy has been described by J. W. Bell (1). His apparatus consisted essentially of a photometric device that would measure the turbidity of fine particle suspensions. Turbidity, in this case, was considered as a function of surface area. Bell&apos;s method of surface area determination seemed to offer possibilities of extension and improvement to the point where it might approach a general method of particle size measurement. Theoretical and Practical Considerations of the Photometric Method In order to illustrate how turbidity may be considered as a function of average particle size, and to indicate the type of results expected from a photometric method of particle size measurement involving turbidity, the following theory may be hypothecated. If a number of particles, considered as spheres of uniform diameter, are placed at random in the path of a beam of light, the following expression, which will give the change in light intensity as a function of the diameter of the particles, the specific gravity of the material, and the weight involved, can be formulated from the Beer-Lambert Law:

Jan 1, 1951