Search Documents

By Thang V. Nguyen, Lisheng Shao, Gary E. Taylor

"The Community Memorial Hospital of Ventura, California, proposed to build a new state-of-the-art Cancer Treatment Center with radiation shielding walls and roof. The loose silty soils at the site had the potential to liquefy during an earthquake, which would result in significant settlement under the heavy footing loads. Treatment options included various deep foundation alternatives, as well as several ground improvement methods. The choice of wet soil mixing minimized the disturbance to the adjacent hospital during construction and potential settlement. Wet soil mixing allowed the structure to be supported on a raft foundation, meeting the stringent building total and differential settlement criteria. The authors also performed unit cell 3-D finite element analyses to evaluate the behavior of the wet soil mixing system in seismic loading conditions. This paper highlights the ground improvement design, construction, QA/QC, and the research related to evaluating the effectiveness of soil mixing for liquefaction mitigation.INTRODUCTIONThe Ventura Community Memorial Hospital proposed the construction of a new Cancer Treatment Center to replace the existing structure, which was built in 1901. The hospital complex is located in a wellestablished residential neighborhood. The soil conditions at the site of the proposed structure required ground modification to support the very heavy radiation treatment section of the building and limit settlement. Originally, 90-foot-long precast piles were considered for foundation support. Based on supplemental Cone Penetration Tests (CPTs) performed, the deepest CPT did not encounter competent pile bearing strata at a depth exceeding 30.5 m (100 ft). This could result in failure of the piles under long-term conditions, especially if hydro-consolidation occurs. The more realistic pile penetration depth would have been 36.6 to 45.7 m (120 to 150 ft). In addition, the excessive noise in association with pile driving would have been unacceptable to the community, patients, and staff of the hospital, so an alternative ground improvement solution was required.The specialty geotechnical contractor recommended wet soil mixing, an economical solution of creating a soil-cement product known as soilcrete that would significantly reduce the construction related noise and provide a more complete deep foundation for the structure.SOIL CONDITIONS AND SETTLEMENT CONCERNSThe subsurface soils were interbedded (Fig. 1) consisting of loose to medium dense silty sands, and soft to medium stiff silty clays to a depth of 30.5 m (100 ft). Groundwater was encountered at depths of 9.1 m (30 ft) and historical high groundwater was at 8.5 m (28 ft) below the ground surface."

Jan 1, 2015

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to assist the mining industry in implementing continual improvement in management of major unwanted events so maximising health and safety performance. A comprehensive body of knowledge has been compiled from diverse mining industry experts for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This paper presents an overview of the RISKGATE body of knowledge captured specifically for the management of unwanted events that stem from the handling and use of explosives (drill and blast) within surface coal mining operations. The knowledge presented is divided into a series of initiating events (listed below) within which there are further degrees of classification based on design, operation, and management concerns. Initiating events: ? Loss of control of explosives and associated chemicals in storage on site ? Loss of control of explosives and associated chemicals during transport ? Loss of control of explosives and associated chemicals during manufacture ? Loss of control of explosives and associated chemicals during handling and blast operations ? Loss of control of explosives and associated chemicals during disposal The system guides the user in generating substantive and leading-edge controls to assist in the design, management and reporting of drill and blast operations to meet stringent internal and external requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.

Aug 1, 2013

By Robert F. Stevens, Robin Givet, Kenneth Viking

"Summary This paper describes a case of a directional pile installation conducted from an existing oil platform in the Caspian Sea, offshore Baku. Results are presented for 660 mm outer diameter (660 mm OD) conductor piles. Each conductor was equipped with a beveled aluminum toe for directional impact driving and was driven through a 710 mm casing using a Delmag 100–13 diesel hammer and a chaser pile. The 710 mm casings were preinstalled to a depth of 75 m below mud line (75 m BML). The longest impact driven conductor pile on the project was 456 m at end of drive, and reached the terminal depth of 295 m BML.Soil conditions consisted of soft to stiff silty clay to a depth of 30 m BML, underlain by stiff clay to 96 m BML, very stiff silty clay to 200 m BML, and very stiff to hard clay down to 300 m BML.In order to assess the maximum stresses in the conductors and check the performance of the hammer, the driving of each conductor was monitored using a Pile Driving Analyzer (PDA). The hammer fuel setting was adjusted based on the PDA outputs to ensure the conductors were not overstressed during installation. All driving and monitoring operations were carried out from the drill floor.The conductor piles drove easier than anticipated but in the direction predefined by the pre-cut angle of the beveled aluminum toe. The driving system performance was good. Post driving, the SRD were analyzed by either the global method analysis, using WEAP, or by the CAPWAP program.To detect any collision between the conductor being driven and the adjacent wells in production, the well heads were monitored in real time with high sensitivity accelerometers. These accelerometers were connected to an alarm system on the drill floor, triggering a siren and a strobe light should a collision be detected by an abnormal increase of the peak acceleration.IntroductionThe world longest directional impact driven pile was installed in year 2005. The operation was carried out from an offshore production, drilling, and quarters (PDQ) platform located about 120 km east of Baku, in the Caspian Sea.The platform foundation consists of driven piles and 24 slots were available for drilling the wells to the reservoir, located about 3800 m below sea floor. Each slot was fitted with a casing, 710 mm in diameter, running from the top of the jacket to a depth of about 75 m BML (Figure 1). Oil production started in 1997 and by the end of 2003, 14 wells were in operation; 10 slots were therefore still available, either for oil production or for water injection. However, due to larger than expected settlement of the platform, drilling of additional wells was put on hold. After further investigation, experts concluded the settlement was due to an alteration in the mechanical properties of the bearing strata supporting the foundation piles. This alteration was due to either excess soil material transportation, or soil fracture by the drilling fluids (mud), when drilling the first wells. With only 14 wells in production, out of 24 possible, the owner faced a new dilemma: to drill, or not to drill new wells?"

Jan 1, 2014

By K. A. Natarajan

The relative significance of corrosive and erosive wear in magnetic taconite grinding is examined. The influence of different types of aeration, namely, nitrogen, air and oxygen on ball war was established for mild steel and high carbon low alloy steel balls. Ball wear data from dry and wet grinding tests are compared with those obtained in the presence of an organic solvent that does not promote electrochemical corrosion. 'Marked ball grinding, tests along with electrochemical measurements involving ball material and magnetite electrodes indicate that contribution from oxygen towards wear (corrosive wear) is relatively small and abrasive wear appears to be significant. Rheological properties of the slurry-appear to have an important bearing on the abrasive wear of grinding balls.

Jan 1, 1983

By W. H. Gross

To pollute means to make impure or unclean. We tend to forget that man defecates, urinates, sweats, expectorates and exhales and in himself is a beastly little pollutor-but then so is Mother Nature! The object of this paper is to try to put what man and nature do into perspective. The facts indicate that although man may sweat a little, Ms. Nature is by for the greatest pollutor of all.

Jan 1, 1979

By Edwan Anderson Ariza Echeverri

O aumento das exigências para reduzir o consumo de combustível e aumentar a segurança dos passageiros tem estimulado o desenvolvimento da nova geração de aços de alta resistência. Esses objetivos tornam-se atingíveis com a redução do peso dos componentes de aço do veiculo, pelo uso de chapas mais finas e resistentes, mas não menos dúcteis. Com esse propósito, no presente trabalho pretendeu-se analisar os efeitos de diferentes rotas de processamento: estampagem a quente, têmpera e partição e o inovador processo que combina a deformação a quente com a têmpera e partição. Os ciclos térmicos foram projetados para obter a maior fração de austenita retida, além de ferrita e martensita. Para cada amostra tratada, amostras de tração de tamanho reduzido foram extraídas de amostras previamente tratadas em simulador termomecânico avançado Gleeble 3S50. A microestrutura foi analisada por microscopia óptica e eletrônica de varredura. Com o novo processo combinado acredita-se que seja possível atingir uma boa associação de propriedades para a nova geração de aços de alta resistência pela transformação da austenita retida metaestável em martensita induzida por deformação, contribuindo para a absorção de energia durante impacto.

Aug 16, 2017

By R Markoski, P Grealish

The requirement for rapid vertical development for underground ventilation is often a factor when dealing with dynamic mine plans, with short vertical developments being used to optimise ventilation systems. In an effort to increase the safety and efficiency of the constructions, a simple and effective sinking methodology is required that is both adaptable and repeatable. A modified shaft construction methodology is proposed that attempts to minimise risk to the personnel as well as be cost-effective. Readily available equipment is used to ensure adaptability to the various environments and shaft parameters.One of the greatest risks of shaft sinking is having personnel working suspended over open cavities or underneath suspended loads. Removing this risk, by ensuring all construction is done from solid ground, allows for safer sinking operations. As the process is repeatable, familiarity and confidence in its construction sequence will increase with each successive sink.A trial sink is performed with a 3.6 m diameter, 20 m deep shaft. The shaft was excavated using a conventional strip-and-line philosophy, with the shaft then being lined from the collar via the use of large diameter corrugated steel culverts. The annulus between the steel culverts and shaft excavation is then filled with a concrete mixture to secure it in position.The new process was successful, with no personnel at any time during the process being suspended above an open excavation. The installation had relatively low capital and operational costs and was completed faster than an equivalent, conventional concrete-lined shaft construction. Therefore when compared to conventional shaft-sinking methods, this process can be considered safer, more efficient and relatively cost-effective.Further research is required to determine whether this method can be expanded to larger vertical developments.CITATION:Markoski, R and Grealish, P, 2014. A new method for rapid vertical development of underground ventilation shafts, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 603–606 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By V. E. Dementyev

This paper presents a brief overview of some IRGIREDMET advances in gold hydrometallurgy. Original impulse-percolation technology and equipment for intensive cyanidation of gravity concentrates have been developed and introduced into industrial practice by IRGIREDMET since 1980s (RF Patents N1593250). The process is based on leaching using special hydrodynamic and reagent conditions providing high dissolution rate for coarse gold particles. Gold and silver are precipitated from pregnant solution by cementation or electrowinning. There was also proposed an im-proved cementation method using zinc in a contact with electrically conductive material. The units including closed water recirculation, tails detoxification and semi-dry tails IRGIREDMET is well experienced in gold adsorption technology using ion exchange resins and activated carbons. The comparison of CIL and RIL processes were done for a number of gold mines, for example for Sukhoi Log gold deposit. The properties of prospective foreign and domestic ad-sorbents including strong-base, bi-functional and weak-base resins as well as activated carbons were studied. The Institute has developed some adsorption/elution technologies and equipment, such as a two stage RIP adsorption technology for gold/silver ores, an improved technology for gold elution from loaded resin and carbon, electrowinning cells for gold recovery from RIP and CIP eluates etc. Large scale ?Resin In Pulp? tests using weak-base resin were finalized and process design criteria were developed. Gold plant design is on progress at the moment. Improved technology for carbonaceous (preg-robbing) gold ores was developed. It was tested for some gold deposits including Sukhoi Log. It allows to overcome preg-robbing activities of ores treated and to improve dramatically performance of cyanidation and adsorption circuits. The studies on refractory gold ore treatment including bio-oxidation, pressure oxidation, roasting and ultra-fine grinding were conducted. Heap leach technology was tested and introduced by Irgiredmet for a number of Russian mines. Zinc cementation, activated carbon and ion-exchange resin adsorption were used for gold recovery from pregnant heap leach solutions. The options including combined technology ?Heap leach/ RIL or CIP? for clay ores were also developed and tested. The plant using developed technology is at construction stage now. The study on In-Situ gold leaching was conducted. The comparison of different gold lixiviants for this purpose was carried out. Gold recovery from pregnant leach solution by activated carbon and anionite including gold elution from loaded adsorbents etc. was also studied. In 2000 the In-Situ leaching technology was commissioned at Maminskoye gold deposit (Ural). The technologies for treatment of complex ores and by-products were proposed. For example, the technology of gold, silver, copper and zinc recovery from calcines after sulphuric acid production was developed.

Jan 1, 2014

By Richard D. Miller

This Bureau of Mines publication contains analyses and related source data for 271 natural gas samples from 22 States collected during calendar year 1982. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and chromatograph. The results of the investigation of the occurrences of helium are published annually to make the information available to the petroleum industry and the general public. Twenty-six publications have presented the results of 13,051 gas analyses vide prior to 1982. The first 3 bulletins (1-3)3 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24, 26) containing 7,833 analyses of samples collected since 1960.

Jan 1, 1983

By J. D. Lubahn

The influence of precipitation from solid solution on the subsequent deformation resistance of alloys is well known. However, the influence of precipitation or aging that occurs simultaneously with deformation may be entirely different and of considerable importance. It is thought1 that the presence or absence of a yield point jog in impure iron at room temperature and the presence or absence of discontinuous flow at higher temperatures may be directly related to aging phenomena, particularly since the yield point jog is absent when the carbon and nitrogen are sufficiently removed.2 As a preliminary attack on the problem of simultaneous aging and deformation, three kinds of tests—constant strain rate tensile tests, constant load creep tests, and variable strain rate tensile tests—were carried out on an age hardenahle aluminum alloy. Constant Strain Rate Tensile Tests Stress-strain curves at a strain rale of about 0.001 min-1 were obtained for specimens of 61S that had been quenched into liquid nitrogen after a one-hour solution treatment at 521°C, then aged at room temperature 10 min., 20 min., 4 hr, and 26.5 hr before testing. Strain-time curves were obtained on the same chart with the stress-strain curve by means of an auxiliary pen, driven parallel to the axis of the chart drum at constant speed by a synchronous motor and gear chain. The angle of rotation of the chart drum was proportional to strain. The strain rates reported are the measured slopes of the strain time curves. Constant strain rate was approximated (within a factor of 2) by manual adjustment of the oil inlet valve of the hydraulic testing machine in such a way that the course of the recorder pen was parallel to pre-drawn strain-time lines of the desired slope. The specimens were machined from 9/16 in. rod. The cylindrical portion was 0.357 in. in diam by 13/4 in. long and

Jan 1, 1950

By Chris Ashton, Andreas Rädle, Taner Aydogmus

"The Contract C310 is part of the current biggest infrastructure project of Europe “Crossrail” which is a major new cross-London rail link project and comprises the construction of the North Woolwich Portal, Plumstead Portal and the twin tube Thames Tunnels with a length of approximately 2.6km. Two Mix-Shield TBMs (Diameter 7.12m) were driving through differing challenging ground conditions (Thanet Sand, Gravels, Flint and Chalk) below the ground water table. The two tunnels were underpassing several listed buildings, sensitive structures, operational railway tracks with low overburden and close to existing subway tunnels in an urban environment. Several additional measures as compensation grouting, micro piles and an intensive monitoring has been carried out to ensure a safe tunnelling process. PROJECT OVERVIEW CROSSRAIL Project Crossrail Crossrail is currently the biggest infrastructure project in Europe which has been developed to serve London and the southeast of England. The project includes the construction of twin-bore tunnels on a west-east alignment under central London and the upgrading of existing National Rail lines to the east and west of central London. The new rail track, as shown in Figure 1, starting in Shenfield/ Abbey Wood in the east of London and ending in Reading / Heathrow Airport in the west of London, includes the construction of nine central area stations, providing interchange with London Underground, National Rail and London Bus services, and the upgrading or renewal of existing stations outside central London.Altogether there will be 118km of new rail tracks, including 42km of tunnels and 40 train stations. After completion in 2018, Crossrail expects 200 million passengers per year (Tauriainen, Rädle, Ingram 2013)."

Jan 1, 2016

By P Hagan, S Wang, D Li, B Loh

A study was undertaken to quantify the differences in performance between a full-length encapsulated cable bolt and a partially encapsulated cable bolt. Much research has been reported on the differences in cable bolt design and operational parameters such as borehole diameter and grout type with much of this based on the Laboratory Short Encapsulation Pull Test (LSEPT). However, there is a gap in knowledge surrounding the effect of anchorage length on load transfer and cable bolt performance particularly with respect to the role of the bulb in modified cable bolt designs. The objective of this study was to expand the existing knowledge base of cable bolt performance with the intent of developing a revised design criterion. Alongside a comprehensive review of current cable support theory, design and practice, a series of pull tests was undertaken to compare each anchorage method using a high capacity modified cable bolt. The results serve to confirm earlier work on fully encapsulated anchorage. Both the peak load capacity and stiffness of the fully encapsulated cable bolt were nearly double that of the partially anchored cable bolt. When the tests were repeated in an oversized borehole, while there tended to be more variation in performance, there was little significant difference in the mean results. In addition to anchorage length, there are other factors that contribute to cable bolt performance including in order of sensitivity: embedment length, water-to-cement ratio of the grout, type of grout and borehole diameter. CITATION:Loh, B, Hagan, P, Li, D and Wang, S, 2018. A comparison of the performance of fully versus partially encapsulated cable bolts based on laboratory-scale testing, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 291–302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By T. Plikas, L. H. Gunnewiek, L. Oshinowo

"Electric furnace smelting is one of the principal unit operations for ferroalloy production, and increased process intensity, improved availability, minimal maintenance and a longer campaign life are common objectives for electric furnace operation in order to obtain favourable economics of production. Furnace designers have continued to develop innovative solutions, e.g., furnace cooling systems, that have allowed these objectives to be realised and CFD modelling plays a key role in the design process. Enhanced understanding of the energy transfer process in the furnace and the ability to develop, evaluate and optimize components of the crucible design to match process requirements are the key motivators for modelling.This paper provides an overview of recent applications of CFD to the design of electric furnaces. The aim is to illustrate what can be done, and identify areas where further work is needed in this field. Examples include furnace bath simulation, crucible cooling system design, taphole design, baking of Soderberg electrodes, off-gas systems, and fume control and building ventilation. It is argued that the trend is for numerical models to become more encompassing while at the same time more accessible, and therefore further improvements in furnace design will be realised with continued and well validated modelling efforts.IntroductionOne of the main processing steps in ferroalloy production is the smelting of ore in electric furnaces. The three-electrode, AC submerged arc furnace is most prevalent method for smelting in the industry, with shielded-arc and DC plasma arc furnaces achieving limited application (1,2). Commercial furnaces range in size from a few megawatts to more than eighty megawatts of supplied power, and operate with the objective of maximising the return on capital invested. Maximising productivity and energy efficiency are two pathways to achieving this objective, through process intensification, increased availability, minimal maintenance, and increased campaign life for the furnace and associated equipment. Concurrently, the need to reduce the environmental impact of metal production by controlling the emission of particulate emissions, greenhouse gases, and other harmful by-products must also be met."

Jan 1, 2004

By Fumitaka Tsukihashi

Phase diagrams of the CaO-SiO2-FeOx-MgO, Al2O3 systems are necessary for the analysis of copper smelting reactions and sintering process of iron ore. The effect of MgO and Al2O3 addition on the liquidus of the phase diagram of the CaO-SiO2-FeOx system at low oxygen partial pressure was observed. The liquid phase area changed by the addition of MgO and Al2O3 with a changing oxygen partial pressure from 10-8 to 10-3 atm (10-1 to 102 Pa) at 1573K. The effect of Fe3+/Fe2+ ratio on the melting mechanism is discussed.

Jan 1, 2003

By HENRY COLEMAN

WE as employees of these related companies, I am sure, are proud to be affiliated with them, and have great faith in the sagacity and fore- sightedness of our employers. Most of us here have been called into important positions in these organizations, and it should be our most earnest endeavor to sense and carry them out as if they were our very own. We have been asked to supervise and carry on a work over which our employers cannot personally watch. It has been well said that the most efficient organization is that which requires the least attention from its head. Because of the very nature and condition of our work, which separates us by many miles from our employers and makes it impossible for us to receive attention and instructions from the heads of our departments, save for occasional visits and correspondence, we are given a great opportunity to prove that we can be efficient workers without too much attention from the heads of our departments. There are few employees who cannot do their duty when it is laid before them in specific terms, and when their employers are always there to see that their plans are carried out. But the employee who is really giving efficient service sees his duty himself and willingly does it. '

Jan 1, 1931

By R. Shuttleworth, R. Smith

A Knudsen effusion tnethod I~as been used lo measure the vapor pressure of pure iron in the temperature range 1000° to 1500°C. Neutron-irradiated , natural iron was used and the Mn'~proclzdced by the (n, p) reaction removed by evaporation at high temperature. The results can be represented by the equation: where pM - 1.088 x 107 atm and T, = 20,890°K. A value of 100.2 kcal per g- atom was obtained for AH;. THE vapor pressure of pure iron in the temperature range 1000" to 1500°C has been measured. Radioactive iron and a Knudsen cell technique were used and the Mn' produced by an (n, p) reaction removed by evaporation at high temperature. From the variation of vapor pressure with temperature values of the enthalpy and entropy of solid iron have been found. Previous workers2 used a Lang-muir method and measurements were made over a smaller temperature range than that in this work. EXPERIMENTAL The apparatus used was similar to that of Pyle and Shuttleworth, and McLellan and Shuttle worth. However, because of the higher temperatures the Knudsen cell was machined from tungsten bar and the flanged furnace tube was beryllia. Heating was by passing a high current (70 amp at 7 v for 1500°K) through a strip of tantalum foil laid across the top of the cell and through a turn of molybdenum wire around the furnace tube. This method of heating ensured that the top of the cell was slightly hotter than the base and prevented condensation and re-evaporation from the orifice. The temperature was measured by means of a pt/Pt 13 pct Rh thermocouple spot-welded to the base of the crucible. To ensure accurate temperature measurement the iron was in the form of a thin disc (0.75 cm diam by 0.075 cm) which lay on the base of the cell. The high-purity iron was irradiated in the Harwell pile for a week at a neutron flux of 1.2 X 10" neutrons per sq cm per sec. The isotopes fe'~ and Fe" are produced by (n! y) reactions but only Fe", half-life 45.1 days, is a emitter; Mn which is also a y emitter, half-life 300 days, is produced simultaneously by an (n,p) reaction.' Immediately after irradiation of natural iron the ratio of ~e" to Mn y activity was 100:l. However, manganese is very much more volatile than iron and almost all the y activity of the condensate is due to Mn'~. Thus it was essential to eliminate all the manganeses before any measurement of the vapor pressure of iron was made and this was done by preliminary heating for 20 hr at 1400°C. For each determination the iron was dissolved from the target with acid and the y activity compared to a known weight of iron. By means of a y-ray spectrometer the y-activity measurements were made at the 1.09-mev peak of the 17e5' spectrum where the background was of the order of 3 cpm. Despite the low specific activity of ~e" a mass of 10- " g of iron could be determined corresponding to a vapor pressure of about l0-'' atm. RESULTS The vapor pressures were calculated from the equation: Where m is the mass of iron effusing in a time t through an orifice of area a2, r is the radius of the target, Z is the distance from the orifice to the

Jan 1, 1965

By Jiachen Wang

China is the largest coal producing country in the world. Coal is widely distributed in China and thus the mining conditions are complex and diverse. This paper summarizes the important achievements in the last 20 years in various mining methods including the extra thick seam with large mining height top coal caving, the thick seam with large mining height and top coal caving mining, the steep seam with top coal caving and fully-mechanized mining, the thin seam automated mining, and the backfill mining. At the same time, the rapid advance in the development of mining machinery and manufacturing has also contributed to the advancement of coal mining technology and the great improvement of coal mine safety. The future direction of China?s coal mining is to further improve mine safety as to improve the coal recovery rate, promote the pillar less mining technology, develop high-efficiency backfilling technology, develop steep seam high-efficiency mining technology for seams less than 10m thick, and high recovery mining techniques for extra thick seams, improve the reliability of mining equipment, and strengthen the protection and restoration of surface environments and water resources.

Jan 1, 2014

By Mariana Beatriz dos Reis Silva

A influência do tempo entre passes na evolução microestrutural de dois aços austeníticos, F138 (sem nióbio) e ISO 5832-9 (com nióbio), foi investigada através ensaios de torção a quente em condições industriais. Análises foram realizadas através de microscopia ótica e eletrônica de transmissão, EBSD e microdureza. Menores tempos entre passes produziram menores tamanhos de grãos e de precipitados. Microestruturas mais refinadas induziram a maiores microdurezas. O aço ISO 5832-9 apresentou maior resistência que o F138. Precipitações de TiNbN, após o encharque, e de NbCrN e NbN (5%), durante o processamento, foram observadas no aço ISO 5832-9. Ambos os materiais sofrem recristalização dinâmica, partículas grosseiras (> 200 nm) atuaram como partículas de reforço e partículas menores (< 50 nm) no ancoramento dos contornos de grãos e discordâncias no ISO.

Jan 16, 2018

By Alfredo Plenge Thorne

El presente texto señala diversas alternativas y usos para un modelo dirigido a la optimización de una operación minera en el corto plazo, incidiendo en los aspectos mineros, metalúrgicos y comerciales. El modelo se basa en la función de utilidad financiera, cuando ésta es optimizada respecto de las variables que la conforman. Se prescinde de la variable tiempo, al considerarse este modelo como de corto plazo. Se presentan cuatro ejemplos, dos simulados con data real y dos prácticos basados en el resultado actual de la operación. Asimismo, se provee al usuario una visión integral que incluye las actividades principales de la cadena de valor en la minería; unificando criterios y evaluando los efectos de cada una de las decisiones del operador minero en la rentabilidad global de la operación, al variar los principales parámetros en el proceso productivo.

Sep 14, 2009

By Willard L. Hunter

A series of steel heats, one low-alloy and nine carbon, was made by the Bureau of Mines in a 1-ton arc furnace from ferrous scrap from incinerated refuse, steel cans, and detinned steel cans, both alone and blended with heavy-melting scrap. Two additional control heats, one of carbon steel and one of low-alloy steel, were made from electric furnace heavy-melting scrap to pro-vide comparative data. The steel products were cast into two 4-by 4-inch nominal 50-pound ingots; in most heats, an 8-by 8-inch nominal 7S0-pound ingot was also obtained. Tests of these ingots indicated that reinforcing bars of acceptable quality can be made from urban refuse components such as steel cans.

Jan 1, 1976