Search Documents

By Immo H. Redeker

The Kings Mountain area of North Carolina is the lithium pegmatite center of the U.S., if not of the whole world. We have two spodumene and by-product mineral producing companies, Lithium Corp. of America, and Foote Mineral Company. We also have Kings Mountain Mica and Kings Mountain Silica Companies producing mica. feldspar, quartz and clay from weathered pegmatites in that area. Figure 1 gives the location of the spodumene pegmatite area in North Carolina. The two spodumene producers mine typical pegmatite ore in open pits after removing amphibolite or mica schist overburden which is sold to aggregate producers. The ore reserves are discussed elsewhere in this session. They are in the order of plus 50 million tons but not unlimited. 1.2 The major minerals found and concentrated from the North Carolina spodumene pegmatite ores are tabulated on Table 1.

Jan 1, 1977

By J. S. Peterson

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center (PRC), has conducted research to improve electrical fault detection on coal mine direct current (dc) trolley systems. Present circuit breaker protection systems are current-magnitude-based and cannot discern between normal traffic and high resistance electrical faults. Tests were conducted at cooperating mines to assist in developing a neural-network-based detection algorithm for distinguishing between electrical faults and normal operation. The Fast Fourier Transform of the trolley rectifier current signature served as baseline data for the neural network. During field tests, the algorithm performed with greater than 90% accuracy.

Jan 1, 1997

By Peter N. Blakey, Thiann R. Yu, Douglas O. Tansey

A flexible, efficient, and relatively low-cost drilling and blasting operation has evolved at Texasgulf Canada, Ltd.'s Kidd Creek underground mine. Located 32 km (20 miles) north of historic Timmins, Ontario, the underground operation utilizes a sublevel open stoping method developed with large-diameter blastholes. Over the years, Kidd Creek engineers have experimented with various drill-and-blast techniques, leading to the present-day practice. Continuing work is being conducted to further mechanize the blasting operation.

Jan 6, 1976

By D J. Brake

The risk from fire remains one of the most serious of underground mine disaster scenarios. The impacts of mine fires on the underground ventilation system and the production of toxic gases have been difficult to model and therefore assessments have relied largely on empirical data, historical precedent and subjective opinions. Underground fire modelling software has had limited availability and been technically challenging and time consuming to use especially for routine mine investigations. There has also been no well-accepted set of assumptions for fire modelling in mines, which has resulted in a lack of confidence in adopting its use more widely. This paper describes modelling of three critical fire scenarios in underground hard rock mines: a fire (LHD) in an underground diesel refuelling facility, a fire in an underground explosives magazine and a fire on an underground ore transport conveyor. Modelling was undertaken using VentsimÆs VentFIREÖ fire simulation module. It describes the basis of design, the key assumptions, the methodology used and provides examples of the outputs, conclusions and recommendations. It reviews the impacts of these fires on egress and entrapment strategies in the mine. Some general principles regarding improvements to ventilation circuit design based on this analysis are also recommended. Whilst the fire scenarios were based on actual case studies, they have been disguised for this paper.CITATION:Brake, D J, 2013. Fire modelling in underground mines using Ventsim Visual VentFIRE software, in Proceedings The Australian Mine Ventilation Conference , pp 265-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Erepan P. C

Flash flotation technology was introduced by Outokumpu in 1985. Considerable success was achieved in other plants with similar operations to OTML. Conclusions from site visits and amenability tests performed on plant samples were that the OTML

Jan 1, 1997

By R. B. Tippin

To study continuous operation of the heavy liquid separation (HLS) of minerals, the Bureau of Mines concentrated spodumene from a typical ore. The studies included heavy liquid concentration, removal of the heavy liquid from the mineral products, and recovery of the heavy liquid for reuse. The research program examined the influence of feed moisture, steam consumption, stripping time, and condition of steam. Operation of multiple cyclones in series resulted in spodumene concentrates assaying 92 to 95 percent spodumene and indicated mineral recoveries of 86 to 89 percent. Continuous filtration and steam stripping produced mineral products containing less than I pound of heavy liquid tetrabromoethane (TBE) per ton of material. Problems unique to this process are discussed, including heavy liquid properties and viscosity, toxicity, material handling hazards, and safety precautions.

Jan 1, 1970

By D. R. Spears

The U.S. Bureau of Mines has had an ongoing interest in developing new reagent schemes for floating Stillwater, MT, chromite ore. Previous reagent schemes have been unsuccessful in achieving complete separation, primarily because little is known about the surface chemistry of the minerals in this ore. In order to design a rational reagent scheme, a study of the binding of various functional groups (R = -H, -OH, -CO2H, -NH2) on the two components (chromite and forsterite) of the Stillwater chromite was undertaken. Electron Paramagnetic Resonance (EPR) Spectroscopy was used to determine the adsorption isotherm, from a cyclohexane solution, of spin-probes which contained the functional group of interest. This was complemented by studies of the saturation surface coverage of the spin probe on the two minerals. In each case, more sites existed on chromite than forsterite; however, the forsterite sites were more strongly binding for each functional group. The results are discussed in terms of their implications for flotation.

Jan 1, 1994

By Peter Cammack

Where raw coal from a mine is treated in dense medium separators ash in the washed product is generally very consistent, provided control of the medium suspension is maintained at a given specific gravity. When, however, the washing process is a Baum jig or other similar apparatus, making a separation at rather arbitrary gravities, the control of the product ash is less accurate, particularly in those cases where the design capacity of the washbox is exceeded by the load of high ash fines. In either of these cases an instantaneous measurement of ash while not essential would be desirable, to check the quality of the washed product and provide operator or management with instantaneous warning of changes in ash. Nearly 60% of all British coal mined goes for electricity generation, to burn at 17% ash, and since the overall average ash content of raw coal as mined is about 30% and varies within a range of 18 ? 40%, incombustible material has to be removed. The ash specification could be met either by total washing, or by washing part and blending the clean coal produced with the remaining untreated coal. Some plants use a straight tonnage split, but generally speaking in Britain it has been found more economical to screen and wash the oversize only. In either case for effective quality control in blending an instantaneous determination of the ash content of the product as it is made has been found essential, since standard ash determination by pyrolysis methods is lengthy and provides information too late to be used in the control of plants blending at the rate of 1000 ton/h.

Jan 1, 1976

By Neil Campbell

"The gently-dipping Devonian dolomite beds south of Great Slave lake in northern Canada are nearly every-where concealed by a cover of glacial drift and muskeg. Nevertheless, in 1898 or earlier, four small outcropping areas of dolomite, richly mineralized with lead and zinc sulphides, were discovered. Exploration work performed here up to the end of 1930, included intensive trenching and drilling of the showings, together with mapping and wide-spaced drilling in the surrounding region. This work proved that the discoveries are isolated pockets of mineralization much too small to be commercially valuable by themselves. No evidence of orebodies elsewhere was reported.Meanwhile, mapping by the G.S.C. in the Shield far to the east disclosed major Precambrian faults, some of which can be projected southwesterly (under a cover of Paleozoic sediments) to the vicinity of Pine Point. During the period from 1940 to 1947, consideration was given, by The Consolidated Mining and Smelting Company Ltd., to evidence of a theoretical possibility that, although apparently dormant in Paleozoic times, these faults may have provided a structural control and a source of ore-bearing solutions in some post-Devonian period. From this, it was postulated that the breaks might have created, in the overlying dolomite, a linear array of orebodies concealed by overburden but lying in a belt of considerable length and in a position predictable within practical limits. A program of drilling designed to test and exploit this specific concept was conducted from 1948 to 1955.he drilling within the new, theoretically-defined search area resulted in the discovery of many lead-zinc ore-bodies, none of which was exposed at the surface. Some of these are large and (as indicated by 1965 production records) very rich. They are situated 1 to several miles distant from, and apparently not connected to, the earlier-known surface discoveries. The drilling also disclosed that the ore, which consists of disseminated sphalerite and galena replacements together with colloform sphalerite and coarse galena cavity fillings, occurs mainly at certain stratigraphic horizons within a large, coarsely-recrystallized dolomite barrier reef. Considerable fracturing and folding was found. It has been suggested that reef development was influenced by post-Precambrian tectonic movements associated with the old faults in the basement complex. The ore may have been deposited by solutions moving from distant sources to favourable structural and chemical environments in or related to the reef.In more recent exploration performed in the course of preparing for mining production, the rate of ore discovery within the same general geological context has been greatly accelerated by the use of new geophysical techniques and drilling equipment. Reserves of 21.5 million tons, averaging 4 per cent lead and 7.2 per cent zinc, were reported in 1965, and production from open pits at the rate of approximately 248,000 tons of concentrates per year is in progress"

Jan 1, 1966

By Pate W. T

This paper describes the development of a dynamic flowsheet simulator for comminution operations. Object oriented software design allows the handling of multiple ore types, blended into multicomponent feed streams. Software objects have been c

Jan 1, 1998

By B. Seegmiller, W. A. Hustrulid, O. Stephansson

Introduction The concept of in-the-wall haulage was formally introduced to the mining community in the early 1970s. The basic concept is simple. Rather than the traditional in-the-pit haulage/access ramp, single or twin ramps driven in the pit wall are used with crosscut connections on the working levels. The in-the-wall pit haulage system could be considered as part of the opening of a new mine, a way of completing to final depth an existing pit, or part of the transition from open-pit to underground mining with the ramp remaining as part of the access. This paper is intended to acquaint the reader, particularly mine planning engineers, with some of the possibilities presented by the concept. Nordstrom (1983) said, "In many countries, mining engineers are either open-pit or underground specialists and, hence, often don't consider the possibilities for combining the best aspects of each into a hybrid mining system." This is believed to be true. There are few "hybrid mines" employing, for example, open-pit methods with underground haulage systems. One reason is the variance with the experience of the mining company and the engineers involved. However, with today's low metal prices, innovative and unconventional thinking may be just what a property requires to remain in production. All the possible situations where an in-the-wall ramp might be considered cannot be presented here. Rather, a few examples will be discussed for illustration purposes. Potential savings in stripping costs A major cost in open-pit mining is associated with the removal of overburden and waste rock. Although much of this stripping cannot be avoided, the volume (V) associated with the presence of an in-pit haul road can be quite large, V 100 (pit depth) a (road width) 2 x road grade (%) As an example, consider a vertical ore body 400 m (1312 ft) long, 60 m (197 ft) thick, extending to a depth of 160 m (525 ft). Cross sections are shown in Fig. 1. Other data are: ore tonnage = 11 Mt (12 million st), ore density = 2.9 t/m3 (0.09 st per cu ft), waste rock density = 2.7 t/m3 (0.08 st per cu ft), road width = 20 m (66 ft), road gradient = 10%, and level interval = 10 m (33 ft). The evaluation has been made assuming that the pit slope (0) is constant around the pit except on the side with the haul road. On this side, the slope is decreased to allow for the road. Slope angles of 30° to 60° have been selected to indicate the dependence of stripping volume (V) on slope angle. The stripping at the ends have been calculated assuming representation by cones. The volume associated with the haul road is 2.6 Mm3 (92.8 million cu ft). A comparison of the strip volumes involved is shown in Table 1. As can be seen, the percent savings in strip volume varies from about 4% to 17% and depends greatly on the slope angle. It is perhaps more interesting to examine the savings in stripping costs that could then be used to cover the cost of the access ramp and the crosscuts for stripping costs of $3/m3 ($0.08 per cu ft). The cost with the road volume is 2.6 million x 3 = $7.8 million.

Jan 1, 1988

By Martin B. Hudson, Andrew K. Cho, Rolff B. Knobel, Les R. Chernauskas, Jonathan L. Ernst

ABSTRACT The Bruce Museum, located in Greenwich, Connecticut, is home to an extensive display of art and natural history exhibitions. A large addition was designed to be constructed adjacent to the museum requiring new spread footings to be installed up to 16.5 feet below the existing foundations. The soil conditions at the site consist of highly variable sand and gravel overlying weathered rock and sound bedrock. The Contract Documents called for traditional foundation underpinning. Traditional underpinning techniques, however, presented two major challenges on this Project; (1) deep underpinning pits would be required involving multiple levels and staging with tieback support and (2) the highly variable soil and bedrock composition and elevations presented uncertainty in the design and construction of the pits. In lieu of traditional underpinning, Geosciences Testing and Research, Inc. (GTR) proposed an “active” soil nail underpinning system. A major reason that the soil nail underpinning option was feasible, related to the fact that the soil nails and facing could be installed slightly in front of the existing footings rather than directly underneath the existing footings. The soil nail wall design involved one to four rows of soil nails with nail positions and wall depth able to be adjusted “on the fly” as excavation progressed depending on the field conditions encountered. To create the “active system,” the soil nails were pre-loaded to mitigate wall deformations that would be associated with a standard passive soil nail wall design. To evaluate the performance of the active soil nail wall and confirm design assumptions, an extensive automated monitoring, on-site testing and inspection program was proposed and executed by GTR to monitor deformations of the wall and the museum in real-time, evaluate and confirm bedrock and soil bond stresses and ensure that each soil nail was pre-loaded and locked off. Careful analysis, planning, and use of the observational method illustrates the importance of collaboration between design and construction personnel and applying engineering judgement throughout construction. The use of the observational method includes the potential for modifying design based on conditions observed. This paper presents a unique case study of the “active” soil nail underpinning system to support and protect sensitive structures, close collaboration between design and construction facilitated by real-time deformation monitoring, and its successful application as a safe and cost-effective alternative to traditional underpinning.

Oct 1, 2022

By Yuanyuan Wang, XUEWEN WANG, Jinzhi Wei, Ligang Wen, Muxin Jia, Zhengyao Li

The abstract discusses the use of disodium carboxymethyl trithiocarbonate (D8) as an effective depressant in the flotation separation of stibnite and pyrite. The study investigates the mechanism behind D8's selective inhibition of pyrite, utilizing techniques like micro-flotation experiments, contact angle measurements, infrared spectroscopy, adsorption capacity analysis, and zeta potential measurements. The findings reveal that D8 physically adsorbs onto both pyrite and stibnite, but its adsorption capacity on pyrite is significantly higher. This adsorption enhances the hydrophilicity of the pyrite surface, hindering the adsorption of the collector and effectively depressing pyrite flotation, while having minimal impact on stibnite floatability.

Mar 14, 2022

By A T. Spathis

The 11th International Symposium on Rock Fragmentation by Blasting (FRAGBLAST 11) was held in Sydney, Australia, between 24-26 August, 2015. The 93 papers, including six keynote presentations, covered exciting and practical topics in 20 sessions within 12 themes. Just fewer than 300 delegates from 27 countries attended. Four workshops were conducted on the weekend prior to the symposium, with three field visits after the symposium to Sydney region quarries, the Hunter Valley coal mining region, and the Kalgoorlie gold mining region. Delegates had the opportunity to visit the exhibition areas that showcased the latest products, software, hardware and systems in blasting technology. The keynote addresses were held in plenary sessions and set the tone for the parallel sessions that followed. They spanned the dynamics of the mining industry, the detonics of explosives, the interaction of stress waves and fracture mechanics in fragmentation, wall control blasting, and the importance of education and engineering for full process optimisation.

Jan 1, 2015

By Catharine T. Fogg

The U.S. Bureau of Mines investigated the availability of platinum, palladium, and rhodium from 16 deposits in four market economy countries (MEC's). Major recoverable products include 164 Moz of platinum, 80 Moz of palladium, 13 Moz of rhodium, 24 Moz of ruthenium, 4 Moz of Iridium, 2 Moz of Osmium, and 10 Moz of gold. The 12 deposits in the Republic of South Africa are estimated to account for 96.7 pct of total recoverable platinum. The base-case scenario estimates the long-term cost of production including recovery of capital, but provides no return on the investment or O-pct discounted cash-flow rate of return (DCFROR). The total production costs in January 1990 U.S. dollars ranged from $325/oz to $1,288/oz of platinum compared to an average January 1990 price of $492/oz. Approximately 83 pct of total recoverable platinum was economic at a cost level of $4S0/oz or less. At the IS-pct DCFROR, only 26 pct of total recoverable platinum was economic. For platinum-group metals (PGM), attention has been focused on the ratios of the three primary metals: platinum, palladium, and rhodium. Sensitivity analyses were performed to determine the impact long-term rhodium price increases could have on the total cost of production for platinum and palladium.

Jan 1, 1993

By S France

The Waterview Connection will complete a strategic Auckland motorway route linking the south, west and north. The project will comprise 2.5 km of ‘undrained’ driven tunnels and 900 m of drained cut-and-cover tunnel and portals.The project is aligned beneath a stream valley of Oakley Creek incised through alluvium and in places overlain by landfill, between Mt Albert volcano and a ridge formed in alternating sandstones and siltstones. The hydrogeology of the area is complex with perched aquifers in compressible soils, cascading water levels in fractured rock aquifers, and discontinuous higher permeability units resulting in artesian water levels and groundwater springs.Numerical groundwater modelling was undertaken to assess the potential effects of tunnel construction and long-term operation on the groundwater system; the magnitude and extent of changes in groundwater level and the resulting potential for settlement, buoyancy effects, contaminant migration and adverse effects on creek base flow. Modelling also provides inputs to tunnel design such as groundwater seepage volumes and water pressures.The driven tunnel will be ‘undrained’ long-term so potential effects on the groundwater system are limited to short-term dewatering during construction. Significant project time and cost savings can be made if the portal areas are permanently ‘drained’, but this means potential effects are greatest in the long term condition.This paper summarises the investigations, implications of the complex hydrogeological setting on tunnel design and environmental assessments, and groundwater modelling undertaken during the planning stage of this project. The groundwater modelling has been used to incorporate mitigation options in tunnel design and construction sequencing; a comprehensive monitoring program will be used to trigger appropriate responses should effects differ from those predicted.

Mar 8, 2011

Development of a global failure criterion for rocks has been a desired goal in rock mechanics. Due to variations in factors affecting rock specifications and their mechanical properties, proposing a single failure criterion suitable for all rock types has proven to be unachievable. The theoretical failure criteria do not fit the real data correctly. Amongst empirical criteria, the Bieniawski criterion has demonstrated an acceptable agreement with laboratory generated data. It has been experienced that the ability to estimate rock strength via the modified form of this criterion is significantly improved. Based on the modified Bieniawski criterion and using VB.net, an associated Microsoft Windows program named 'RAMOCE' has been developed. The inputs of RAMOCE can be triaxial compressive strength data, Bieniawski parameters of a specific rock or the type of given rock. Based on input data, potential outputs of the program are Bieniawski's rock parameters, sensitivity analysis of the effective parameters, rock failure prediction and defining the type of given rock.

Nov 25, 2010

By R. V. Ramani, W. Miola, R. Srikanth, S. C. Soboleski

"Dust control in high-production longwalls requires attention to operating practices and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in US longwalls. Yet, under certain conditions, 31% of the shearer operator's dust exposure can be due to support movement.Several methods have been developed for the control of shield-generated dust. But the need for better methods is apparent. In this paper, the amount of airborne, respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. Ten experiments were conducted on five longwall faces in four mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne, respirable dust concentration immediately downwind of the shield move varied between 0.12 and 1.75 mg/m3 in the five longwall faces. The mass of airborne, respirable dust gener-ated by shield movement was found to vary between 39 and 386 mg per shield move. The results from this study reveal that control of dust from longwall shields requires a combi-nation of approaches involving alternative operating prac-tices, reducing shield dust generation rate, increasing face air flow and decreasing personnel exposure.IntroductionIn 1992, longwall mining accounted for about 36% of US underground coal production, a 240% increase from a decade ago. The absolute longwall tonnages were 46 and 133 Mt (51 and 146 million st), respectively. Compared with room-and¬pillar mining systems, the longwall mining system is charac¬terized by higher recovery, enhanced safety and higher pro¬ductivity.However, personnel dust exposure on a longwall face is higher than in other types of mining. According to Mine Safety and Health Administration (MSHA) data, fewer longwalls were in continuous compliance with the applicable dust standard in 1992 than in 1989.Controlling shearer-generated dust and reduction of per-sonnel exposure to airborne dust have commanded attention in the design of longwall faces, operational practices and ventilation schemes. Studies in the United States and abroad have revealed that support-generated dust can be a major obstacle to compliance under certain conditions (Becker et al., 1989; Bradley et al., 1983; Jankowski and Organiscak, 1983; Jankowski et al., 1990; Organiscak et al., 1985)."

Dec 1, 1996

By G. L. Oldright

The past reputation of zinc as an ingredient in lead blast furnace slags has been bad. Zinc is thought of as a cause of accretions in the shaft of the blast furnace, of hot tops, of the formation of "zinc mush" in the crucible and forehearth, of leach rich slags, of viscous slags, and of low capacity in smelting.

Jan 1, 1934

By W. Curlook, L. M. Pidgeon

THE PURPOSE of this investigation was to study part of the ternary system Co-Fe-S. Jensen ( 1) established the solubility limits of sulphur in pyrrhotite. The compound with 61.7 per cent Fe, corresponding to a formula Fe12S13, was found to melt congruently at l,192°C. Hulsmann and Weibke(2) determined the Co-S phase diagram from O to 35.2 per cent S. The solubility limits of sulphur in the com-pound Co(l-x)S were not determined. The initial object of the present in-vestigation was to determine the composition at which the compound Coci-xiS melted congruently. Once this was ascertained, it was decided to investigate the ternary system Co-Fe-S from the region of 100 per cent Co(1-x) S to the region of 100 per cent Fe12S13.

Jan 1, 1953