Search Documents

By G. S. Littlejohn

Following study of historical South African practice and a review of recent experience gained during the design, construction and testing of the high pressure plugs at the South Deep Water Barrier Project, this paper makes recommendations to improve practice. Initially, site investigation requirements are described with reference to geological, hydrogeological and seismic considerations, including site preparation and pre-grouting of the surrounding rock mass, if permeable. Structural and hydraulic aspects of plug design address topics such as residual permeability, aggressive mine water, plug materials, mortar strength and bleed. In situ thermocouples and piezometers are recommended to optimize the timing of plug tightening and monitor plug performance during service. Plug construction covers aggregate preparation, mortar quality control, plug tightening grouts, injection pressures, records and the overriding need for a method statement specification to control all aspects of plug construction. On completion of the plug, tests to establish surrounding rock stress regime, plug strength, and residual permeability are described to enable a comparison with original design assumptions. Monitoring and maintenance procedures are proposed to ensure satisfactory long-term performance of the plugs.

Jan 1, 2006

By A. Farnoud

Thousands of miners, construction workers, and truck drivers are exposed to diesel exhaust particles. Diesel Particulate Matter (DPM) is a probable human carcinogen and stringent occupational and environmental standards have been established or are planned worldwide. Modifications in fuels and diesel engine designs have reduced emissions, but may not be enough to comply with the tightest standards. Post-combustion aftertreatment devices are likely necessary for many engine operators. However, even the most common and well studied aftertreatment devices fail from time to time. The objective of this study was to design, construct, and test an electrostatic aftertreatment device to treat DPM. An electrostatic precipitator (ESP) was designed and constructed to capture DPM from diesel exhaust, and different configurations were tested to optimize its performance. DPM was produced by a 6 kW diesel-powered electric generator and directed to the ESP through a short section of galvanized steel pipe after the muffler. Number and mass removal efficiencies were measured with a condensation particle counter (CPC) and by sampling through a stainless steel cassette and collecting the DPM on Teflon filters. Particle size distributions were measured with and without control using a 6-stage cascade impactor. The experiments were performed with the engine running at idle and also at medium load. The results show that our first generation ESP provides 60 percent mass removal efficiency, and up to 80 percent number removal efficiency. Power consumption was generally low, about 20 to 30 watts, to achieve these levels of performance.

Jan 1, 2009

By Louis P. Domingues

As part of a study on high-temperature ceramic materials, the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of yttrium, lanthanum, and cerium were analyzed thermogravimetrically. The temperature ranged from room temperature to 1,500° C. Each salt was decomposed by heating at a rate of 2.5° C. per minute, and some of the salts were subjected to additional rates of 5° C. per minute or 10° C. per minute. The decomposition sequences have been identified, and the temperatures of formation of intermediate compounds and of the oxides have been determined. The minimum oxide formation temperature of a given lanthanum salt exceeds that for the similar salt of yttrium, and both exceed that for the same salt of cerium except for one cerium carbonate. Variation of the heating rate indicates a thermal lag in the materials and produces the shift of formation temperatures to higher values and loss of resolution in the weight-loss distribution as the heating rate increases.

Jan 1, 1962

By W. Banda

"Trial application of air decks on a production shot improved fragmentation (32% reduction in x50). Empirical fragmentation models and digital image processing software were used to estimate fragment size distribution of the blasted muck pile. The x20, x50, and x80 passing fractions, and top size were 42, 265, 683, and 1,455 mm, respectively. Air-deck application reduced explosives load in blastholes, lowering total charging cost by US$20/hole (15% decrease) and the powder factor to an average of 0.86 kg/m3 (12% decrease). Blast results were 443,624 t of blasted material from the block (90% of total muck pile) was smaller than 900 mm.RÉSUMÉ L’application pilote de trous d’air dans le cadre du coup de mine effectué pour commencer la production a amélioré la fragmentation (une réduction de 32 % des x50). Des modèles empiriques de fragmentation et un logiciel de traitement numérique des images ont permis d’estimer la composition granulométrique des fragments du tas de déblais abattus. Les fractions de passé de crible de x20, x50, x80 et la dimension supérieure étaient représentées par des dimensions respectives de 42, 265, 683 et 1 455 mm. L’application de trous d’air a permis de diminuer la charge d’explosifs nécessaires dans les trous de mine, réduisant ainsi les coûts totaux de chargement de 20 $ US/trou (soit une réduction de 15 %) ainsi que le facteur de chargement (facteur poudre) à une moyenne de 0,86 kg/m3 (soit une réduction de 12 %). Les coups de mine ont résulté en 443 624 tonnes de matériaux abattus du bloc (soit 90 % du tas de remblais total) mesurant moins de 900 mm. INTRODUCTIONThe main objectives of production blasting are to achieve optimum rock fragmentation and to minimize overall production costs. Because blast fragmentation significantly affects the profitability of a mine, blasting is the first step of the size reduction in mining: An optimum size distribution is required to maximize the performance of mining and subsequent milling processes. If the fragmentation size distribution can be modelled and controlled, operations performance will improve. Blast fragmentation modelling is important in mineto- mill optimization: It allows the estimation of blast fragmentation distributions that can be modelled in downstream mining processes to determine the optimum blast design."

Jan 1, 2018

The development of information concerning mesothelioma in South Africa started with the 1959 finding of Dr. J. Christopher Wagner of cases of mesothelioma in persons living in the vicinity or working in crocidolite mines in Cape Province. After more than 40 years, the data from South Africa now provide important insights into the differences in mesothelioma risk associated with different asbestos fiber-types. Three case series reports and one analytical report were reviewed in this session. In total, information on 504 proven cases was presented. There were 28% of cases arising from occupational exposure in mining, 35% from non-mining occupations, 23% from environmental exposures; 14% where no exposure was established and 9% where the exposure was unknown. Among the 129 cases for which occupational exposure and asbestos fiber-type were established, 115 cases were associated with occupational exposure to Cape crocidolite; 1 case associated with occupational exposure to Transvaal crocidolite and 9 cases with occupational exposure to amosite (grunerite asbestos) and 4 cases with occupational exposure to mixed fiber-types. There were no cases associated with chrysotile asbestos. There were 33 cases of environmental mesothelioma linked to Cape crocidolite exposure and 2 to exposure to amosite and crocidolite but none to Transvaal amosite alone or to chrysotile. The evidence shows that amosite is capable of causing mesothelioma but that the major risk in South Africa is associated with Cape crocidolite.

Jan 1, 2008

By Gregory J. Chekan

This Bureau of Mines report presents three methods for designing bulkheads to impound water underground: (1) thin and thick plate design; (2) South African plug design; and (3) single and double bulkhead seal design. Related areas critical to the long-term effectiveness of underground water impoundments are also addressed. These include bulk-head anchorage, concrete specifications and placement, the grouting of permeable strata, and the sizing of barrier pillars. A case study involving hydrostatic tests conducted on a single bulkhead seal constructed in the Safety Research Coal Mine of the Bureau's Pittsburgh Research Center is presented in an appendix.

Jan 1, 1985

By Oliver C. Ralston

[This paper is an expmded revision of a report entitled "Froth Flota- tion and Agglomerate Tabling of Honmetdlic Idinerds, " published in Trans- actions of the Canadian Ir-stitute of Iriining and !,letdlurgy (vol. 40, November 1937, pp- 6? 1-726) and al'enared a year pr~viousl:~. Revisions en'oodied herein brinc the &ta I:T to Jn?uac"g 1, 193;. References have also been added to make the earlier paper more complete for the period it covered. This paper is an expmded revision of a report entitled "Froth Flota- tion and Agglomerate Tabling of Honmetdlic Idinerds, " published in Trans- actions of the Canadian Ir-stitute of Iriining and !,letdlurgy (vol. 40, November 1937, pp- 6? 1-726) and al'enared a year pr~viousl:~. Revisions en'oodied herein brinc the &ta I:T to Jn?uac"g 1, 193;. References have also been added to make the earlier paper more complete for the period it covered.]

Jan 1, 1938

By Oliver C. Ralston

[This paper is an expanded revision of a report entitled "Froth Flotation and Agglomerate Tabling of Nonmetallic Minerals, " published in Transactions of the Canadian Institute of Mining and Metallurgy (vol. 40, November 1937, pp- 691-726) and prepared a year previously. Revisions embodied herein brine the data up to January 1, 1938. References have also been added to make the earlier paper more complete for the period it covered.]

Jan 1, 1938

Recycling of Process Water in Sulfides Processing and Flotation Selectivity

Sep 13, 2010

Results obtained from small scale tests using Australian tin concentrates indicate that metallic tin containing less than 0·1 per cent iron can be recovered by a two-stage process using hydrogen and make-up chlorine. In the first stage the concentrate is ground,. pelletized, roasted, and reacted at 650°C with HCI and H2 to volatilize the tin as SnOI2. The volatilization reaction is conducted with cocurrent gas and solids flow because it was found that the use of cocurrent flow yielded a solids residue substantially free from FeCI2. The second stage uses a technique termed "reflux reduction" during which the SnOl2 produced by volatilization is reduced by hydrogen to form tin and a gas containing HCI and H2 of sufficiently high HCI tenor for recycle to the volatilization stage. The elimination of tin ranged from 98+ to 99·7+ per cent of the tin from concentrates containing 5 to 50 per cent tin, respectively. The process should be capable of continuous operation, and a tentative calculation has shown ,that a treatment rate of 12,000 tonnes of tin concentrate per year could be obtained in a volatilization reactor 1·1 m in diameter and 6·1 m high. The process may have particular application to finely divided concentrates containing less than 20 per cent tin.

Jan 1, 1974

By Kwangmin Kim, Junnhyeok Park, Taehee Lee, Minkyu Kim

Mine tailings storage facilities (TSFs) can be a significant source of fine, respirable dust. This dust poses concerns, especially for nearby communities, because of its detrimental impact on respiratory health. To address these concerns, this study examined the effectiveness of commercially available polymers, known for their biocompatible and environmentally friendly features, to prevent dust generation from upstream-type TSFs in active mining operations. It focused on two areas in TSFs: the tailings beach and slope/dike surfaces. Two types of polymers—polyethylene glycol and poloxamer—were selected, and their effectiveness was evaluated in a series of phased laboratory and field tests. The lab tests investigated the moisture-retention capacity of the tailings after treatment with the polymer solutions as well as the ability of these solutions to reduce dust emissions. Polymers were applied to a tailings bed surface in the lab and dust was generated from this surface using a wind tunnel. PM10 and PM2.5 concentrations were measured using laser-diffraction dust sensors, and the polymers were found to have reduced dust emissions up to 95%. Small-scale wind-blowing tests were conducted in the field (specifically, in a controlled environment at a TSF) to evaluate polymer effectiveness on the tailings beach and slope/dike areas. The tests revealed that the AP could efficiently suppress approximately 80% of PM10 and PM2.5 dust emissions at both types of areas. Finally, 1000 gallons of AP solution were discharged at the top of tailings beach and slope/dike areas, respectively, and found to be effective. The results of these tests showed the high potential of the biocompatible polymers to be a feasible solution for reducing the respirable dust emissions from upstream TSFs in arid and semi-arid regions.

Keywords: Pyrometallurgy, Pretoria University Substantial research in pyrometallurgy at the University of Pretoria started in 1980 with the appointment of Rian Dippenaar to the Iscor Chair, a position that he held until 1996, when Chris Pistorius became the leader of this pyrometallurgy group. This paper reviews the main research themes over the quarter-century from 1980 to 2005, as well as some of the industrial developments that have shaped the research approach. The main topics have been the use of electrochemical sensors for equilibrium measurements, ilmenite smelting, steel processing, and reduction.

Jan 1, 2006

A study of the electrolysis of PbS in molten PbCl2 showed cathode efficiencies which increased with current density at fixed sulphide concentrations, and decreased with increasing sulphide concentration at fixed current densities. The anodically produced sulphur dissolved rapidly in the melt, the rate increasing with temperature and sulphide concentration. Experiments with diaphragm cells, made to determine the relative effects that dissolution of lead and sulphur have on the cathodic current efficiency, demonstrated that dissolution of sulphur was the major contributor to the lowering in efficiency.

Jan 1, 1973

By A-A. Bogno, Ch. -A. Gandin, A. Maitre, H. Henein

Most metallic materials are produced from their liquid state. In order to control the properties of industrial products, it is very important to understand their solidification path and the resulting microstructures which can be significantly affected by melt undercooling. High undercooling results in rapid solidification and a refined microstructure with minimal microsegregation. This paper reports on the analysis of rapidly solidified Al-Cu droplets obtained by a single fluid atomization process, Impulse Atomization. A quantitative analysis by Rietveld refinement method of the Neutrons Diffraction data was carried out to determine the fraction of the intermetallic Al2Cu. Knowing the fraction of Al2Cu, the eutectic fractions and corresponding dendritic and eutectic undercoolings were estimated using the metastable extensions of solidus and liquidus lines of the Al-Cu system calculated by Thermo-Calc. In addition to this work, a model of microsegregation coupled with ThermoCalc software via TQ (application programming interface of ThermoCalc) and the Wang-Beckerman model for dendritic growth velocities has been developed for binary alloys. This has led to the development of a phenomenological relationship between primary phase undercooling and initial growth velocity. A comparison of estimated primary undercoolings using a coarsening model with the adiabatic undercoolings for each alloy composition has confirmed that solidification occurs under adiabatic conditions during recalescence.

Jan 1, 2014

By Kwangmin Kim, Junnhyeok Park, Taehee Lee, Minkyu Kim

Mine tailings storage facilities (TSFs) can be a significant source of fine, respirable dust. This dust poses concerns, especially for nearby communities, because of its detrimental impact on respiratory health. To address these concerns, this study examined the effectiveness of commercially available polymers, known for their biocompatible and environmentally friendly features, to prevent dust generation from upstream-type TSFs in active mining operations. It focused on two areas in TSFs: the tailings beach and slope/dike surfaces. Two types of polymers—polyethylene glycol and poloxamer—were selected, and their effectiveness was evaluated in a series of phased laboratory and field tests. The lab tests investigated the moisture-retention capacity of the tailings after treatment with the polymer solutions as well as the ability of these solutions to reduce dust emissions. Polymers were applied to a tailings bed surface in the lab and dust was generated from this surface using a wind tunnel. PM10 and PM2.5 concentrations were measured using laser-diffraction dust sensors, and the polymers were found to have reduced dust emissions up to 95%. Small-scale wind-blowing tests were conducted in the field (specifically, in a controlled environment at a TSF) to evaluate polymer effectiveness on the tailings beach and slope/dike areas. The tests revealed that the AP could efficiently suppress approximately 80% of PM10 and PM2.5 dust emissions at both types of areas. Finally, 1000 gallons of AP solution were discharged at the top of tailings beach and slope/dike areas, respectively, and found to be effective. The results of these tests showed the high potential of the biocompatible polymers to be a feasible solution for reducing the respirable dust emissions from upstream TSFs in arid and semi-arid regions.

By E. Amini

"While methods exist to allow the simulation and optimization of existing flotation operations, there is a deficit in the ability to predict the performance of a new ore type pre-processing. A laboratory scale batch flotation testing methodology has been developed to assess the flotation potential of ores (known as the JK Floatability Index or JKFI). Previous work conducted by Alexander and Collins (2008) showed that the test could be used to predict full scale results in base metal ores. In this work, JKFI tests were applied to three different types of ore and one blend from a greenfields gold deposit to show the test applicability to flotation of precious metals. The results from the JKFI test on one ore type were then used to predict the response of all ore types (including the blend). To validate the predicted kinetic parameters, a comprehensive survey was performed on a pilot plant where each of ore types was processed in the circuit. An acceptable agreement was found between the experimental recoveries and predicted recoveries which indicate the potential of this method for use in predicting the flotation response of an ore.INTRODUCTIONOver 100 years, flotation has been considered an efficient method to concentrate different types of sulphide and oxide minerals and coal. Thus, numerous research studies have been undertaken to find an appropriate model to predict the behaviour of particles in flotation circuits (Barnwal et. al., 2006; Bascur and Herbst, 1983; Cecile and Villeneuve, 1991; Deng et. al., 1996; Zheng et. al., 2006). Most methods are based on the ore flotation response in an industrial plant which is expensive and time consuming to characterise. It is difficult to reliably predict flotation response for new types of ores in industrial scale plants.The floatability component modelling (FCM) approach, developed within the Australian Minerals Industry Research Association (AMIRA) P9 project, has been used to derive models of operating flotation plants for the purpose of simulation and optimisation (Alexander and Morrison, 1998; Alexander et. al., 2000; Varadi, 2006). This approach has been applied at a large number of operating sites treating a wide variety of ores. The approach requires metallurgical surveys to be undertaken in conjunction with batch flotation tests and cell characterisation. This allows ore and machine parameters to be derived, which are then used in the P9 Flotation Model. The development of a FCM generally requires a large commitment of resources and time. While there has been significant support of this approach in industry, the FCM approach is limited to ores already being processed (Runge, 2004; Wightman, 2006)."

Jan 1, 2009

By T Hirsi, M Weatherseed, T Ritasalo

Cooling tower design has not advanced significantly in the last decade. Recognising this, Outotec has developed an innovative horizontal outflow cooling tower with increased performance compared to conventional design cooling towers.Outotec® Cooling Towers operate today in applications such as spent electrolyte cooling in zinc plants and for gypsum removal before copper solvent extraction. In such applications the use of this latest design has enabled increased production and lower maintenance costs in the downstream operations.In actual operations, the cooling performance has been confirmed at start-up, and has demonstrated that the towers operate in accordance with the CFD modelling. In the last three years these towers have proven themselves in commercial operation to operate with high efficiency and availability.This case study will outline comparative data, collected over two years at a site where both Outotec and conventional cooling towers are operating. The data shows that Outotec cooling towers require less than half the maintenance time of conventional cooling towers, when adjusted to a total solution flow basis. A close partnership approach with the site has allowed continual development, ensuring high availability and high performance.Experience with previous cooling tower installations guided the development of maintenance philosophies and procedures; this resulted in a design where maintenance intensive components were accessible from the top of the cooling tower. This allows safe access to components and maintenance with little or no downtime.CITATION:Hirsi, T, Ritasalo, T and Weatherseed, M, 2015. Improving cooling tower performance with innovative horizontal outflow design, in Proceedings MetPlant 2015, pp 396–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Robert Bachus, Jamey B. Rosen

"Abstract Large scale In Situ Barrier Wall Construction projects, specifically those related to earth dams, dikes, and levees, frequently require stringent quality control measures to ensure the success of the wall. This presentation discusses the applications of Geographic Information Systems (GIS) technology to capture information from multiple data streams and provide geotechnical feedback, quality control, and project control feedback. Techniques used to geospatially analyze verticality data from secant piles and panels will be demonstrated. Examples will be presented from barrier wall installations at two sites owned by the U.S. Army Corps of Engineers (USACE): the Wolf Creek Dam in Kentucky, and Center Hill Dam in Tennessee.IntroductionDeep foundation installations require contractors to collect a substantial amount of information over the course of a project, both for internal quality control of construction progress and for demonstrating compliance with customer or owner specifications. Methods of collecting information are constantly improving, bringing with it the need for a systemic approach to managing the increasing amounts and types of data. Handling these diverse types of data presents challenges with both budget and schedule demands. This paper discusses some techniques for adding or increasing quality control in barrier wall constructions by consolidating, visualizing and analyzing data using relational database and Geographic Information Systems (GIS) technology, collectively referred to as Information Management System (IMS) development. The IMS concept is designed to facilitate the collection, transfer and processing of data and provide an easy way to remotely access and visualize construction progress.The remainder of this paper presents the needs and objectives of an IMS applied to quality control in barrier wall construction, the components and data flows involved, the capabilities and user interfaces of the systems and the benefits for the end users. Examples are presented throughout from case study projects including: a pile barrier wall applied in the rehabilitation at the Wolf Creek Dam in Kentucky (under contract to the Treviicos-Soletanche Joint Venture), and a secant pile barrier wall currently under construction in the rehabilitation of the Center Hill Dam in Tennessee (under contract to Bauer Foundations Corporation) (both owned by the Nashville District of the USACE)."

Jan 1, 2014

By Joseph J. Wallace, William H. Tavenner, D. A. Reynolds, John M. Provost, James J. Dowd, R. F. Abemethy

"CONCLUSIONSThe investigation shows that there are 5 coal beds of major importance in Wyoming County from the standpoint of present production - Pocahontas No. 3, No. 2 Gas, Sewell, Beckley, and Eagle - and 5 beds of minor importance - Pocahontas No. 6, Cedar Grove, Winifrede, Douglas, and Chilton. The Pocahontas No. 3 bed contains the largest remaining known reserves.Known measured and indicated reserves in all beds, based on a minimum thick¬ness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 2,665 million short tons as of January 1, 1951. Of this total, 2,121 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.Recoverable reserves of coal have been estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Wyoming County, as determined by this investigation, is 55.0 percent. This percent¬age is based on the total thickness of coal (less partings 3/8 inch or more thick) in the bed rather than on the thickness of the coal mined. The known recoverable reserves are estimated to be 1,167 million tons as of January 1, 1951.4. Since most of the Wyoming coals are medium- and low-volatile bituminous in rank and expand during carbonization in modern ovens, they are blended with high-volatile contracting coals."

Apr 1, 1953

Often plant performance suffers as a result of poor control. Poor control leads to low mill throughputs, poor classification and less than satisfactory concentrate grades and overall recoveries. By using the appropriate control tools, substantial gains in plant performance can be made. Mintek?s MillStar and FloatStar controllers have been implemented at various sites across the world. The MillStar controller incorporates leading technology that controls process units from the mill feed through to the flotation feed. Typical results show that milling circuit throughput is increased by 6-10 % and the final product grind size is tightly controlled, thereby enhancing flotation performance. The FloatStar controller is aimed at stabilising and optimising flotation circuits. Through improved level control alone, recovery improvements of up to 1 % have been achieved. Furthermore, by using on-line grade analysers, the controller stabilises final concentrate grades, whilst maximising flotation recovery.

Jan 1, 2005