Search Documents

By K. C. Sole, M. Makonese

Bushveld Belco is commissioning a plant for production of electrolyte used in vanadium redox flow batteries. Owing to the source material, the electrolyte is contaminated with Fe, at concentrations up to 140 mg/L, which negatively affects battery performance. This study examined the use of ion exchange to reduce the Fe concentration to the target value of < 100 mg/L from a feed solution containing 100 g/L V in 4 M H2SO4. Four resins with possible application were identified: Puromet MTS9570, Puromet MTX7010, Puromet MTS9500, and Puromet MTC1600H. Puromet MTS9570 outperformed the other three resins in all batch experiments with respect to loading capacity and selectivity over V, and was evaluated for Fe removal in fixed-bed column loading tests. Based on these data, preliminary sizing and design of a full-scale column was undertaken. Owing to the difficulty of eluting this resin, a philosophy of discarding the resin on loading to full capacity was considered. These data revealed that, despite the high selectivity of this resin for Fe over V, it would be too expensive and impractical to use this resin for full-scale operation under such conditions. It is recommended to remove iron earlier in the flowsheet prior to generation of the 4 M H2SO4 electrolyte.

Dec 11, 2024

By M. M. Oosterveld

"In South West Africa diamonds are mined from ancient beach deposits by the Consolidated Diamond Mines of South West Africa, Limited.To improve the control of mining production, a computer is used for the calculation of statistically more accurate and homogeneous ore blocks. Geological and sampling information has been digitized and stored on magnetic files.The figures derived for each block entail the calculation of the diamond size frequency distribution, the diamond density distribution and the ore reserve by using the density distribution.The diamond size frequency distribution is used for estimating the revenue in an ore block.A description is given of how a linear programming system can be used for production planning."

Jan 1, 2014

By M. H. Kline, Wing G. Agew

"INTRODUCTION The Watson tract was first prospected in 1908, and ore consisting of concretionary psilomelane and wad was found in the bedded residual clays. A small mill using a log washer and jigs was constructed for concentrating the ores -on the bank of Mudhole Run, and it is reported that a few wagon¬loads of ore were shipped via the Norfolk & Western Railway. The operation was of short duration.During World War I, the area was seriously studied by the Federal Geological Survey and Virginia Geological Survey. The Virginia Geological Survey, in Bulletin 173/ reporting the work, lists the property among the few recommended for further exploration.When the shortage of manganese ores in the United States became imminent, the Bureau of Mines was authorized by the 76th Congress, under the Strategic Materials Act, to prospect and explore for manganese. Upon the recommendation of the Federal Geological Survey, a project to undertake this work was started at the old Watson mine in January 1941 and continued until August of the same year."

Apr 1, 1948

By Rosenblatt M, Gilroy J. A C Cunningham C V B

Vaal Reefs Exploration and Mining Company Limited operates one of the largest producing gold mines in the world. The annual production of 76 tons of gold from 12 million tons of ore treated is obtained mainly from underground sources. Daily some 6.6 km of stope face is blasted and 41 tons of explosives is used to break the rock. The mine employs 45 000 men of whom 35 000 work underground. The company operates nine large vertical shaft systems of which seven extend more than 2000 m below surface and an eighth, currently being sunk, will bottom at 3700 m below surface.

Jan 1, 1995

South Africa?s now a member of this body, tailored on the World Bank, and headquartered in Abidjan-Cote d&apos;Ivoire. As a funding agency for capital projects within 59 member countries of the ADB it is to be expected that there are guidelines to the requirements for funding application and for project management and control.

Jan 1, 1996

Jan 1, 1963

By W. L. Dare

This information circular is one of a series published by the Federal Bureau of Mines in which the methods and costs of producing uranium ore on the Colorado Plateau are discussed. This report describes the three largest company-operated uranium mines of Climax Uranium Co. - the G-1, the Mineral Joe, and the Frank No. 1. Climax Uranium Co., a subsidiary of American Metal Climax, Inc., was [corporated] May 11, 1950, just 2 years after establishment of the domestic uranium program by the Atomic Energy Commission. Twenty-five years earlier Arthur H. Bunker, now chairman of the board, American Metal Climax, Inc., organized and operated the U. S. Vanadium Co. at Rifle, Colo.3/ Soon after Climax Uranium Co. was organized, it entered into a contract with the Federal Government to build a uranium-vanadium processing mill in Grand Junction, Colo. Under the contract Climax leased from the Federal Government certain uranium-bearing lands that had been withdrawn from public entry in 1948. From Minerals, Engineering Co. on June 12, 1950, Climax acquired other uranium-vanadium properties on Calamity, Outlaw, and Monogram Mesas in Colorado and on Polar Mesa and in the Yellow Cat area of Utah. To house the milling equipment, Climax leased the old Grand Junction sugarmill building of the Holly Sugar Co. Milling facilities, based on a then new process developed for treating both uranium and vanadium, were completed, and the plant went into production in 1951.

Jan 1, 1959

By Shoukun Wei, Cong Wang, Lin Cheng, Zhiyu Qiao, Jingkui Liang, Weidong Zhuang

"The subsolidus phase relations in the Sm2O3-CeO2-CuO ternary system sintered at 1000°C in air have been investigated by X-ray powder diffraction. The system can be divided into two ternary phase regions and three binary phase regions. Solid solution Sm2-xCexCuO4-y is the only ternary phase in the system. The maximum solid solubility was confirmed to be x = 0.2. The crystal structure, oxygen content and superconductivity of the solid solution Sm2-xCexCuO4-y have been investigated.I. INTRODUCTIONAfter the first discovery of the superconducting ceramic system La-Ba -Cu-O[l] with Tc = 30 to 40K, other families of cuprate-based ceramics have been synthesized with higher critical temperature. These oxides include the R-Ba-Cu-O (R: rare earth) systems (Tc=90K or so)[2,3], the Pb-Sr-(R,Ca)-Cu-O systems (T c = 50 to 100K), the Bi-Sr-Ca-Cu-O systems (Tc=80 to 105K)[4], the T1-Ba-Ca-Cu-O systems (Tc=85 to 125K)[5], the Hg-Ba-Ca-Cu-O systems (Tc=90 to 150K)[6,7], and some others. The improvement of Tc is very rapid. The measurement of the Hall and Seebeck coefficients shows that they all are p-type superconductors. In 1989, Tokura et al.[8] discovered the superconductors R2_XCexCU04_y(R = Nd, Pr, Sm) with Tc=20 to 24K (onset) and found that the charge carrier is electron in contrast to their hole doped counterparts. This discovery increases the fundamental understanding of the cuprate-based superconductors by comparing their characteristics and mechanisms to those of the p-type superconductors.One of the outstanding features of these n-type superconductors is the difficulty in obtaining samples in good charactors, such as the difficulty in obtaining zero resistivity state in single crystal or bulk samples; the semi-conductivity of bulk samples in ordinary state (opposite to the superconducting state) and a reducing reaction involved before the superconductivity has been found[9]. Therefore, it is necessary to optimize the sample preparation of the n-type superconductors. All the n-type superconductors have been found· considerable solid solubility. The compositional variations play a governing role in the carrier doping of the superconducting phases. Also, it is vital to the ceramic processing of superconductors to identify the compatible phases in the phase diagram. Finally, there is always the possibility of finding additional compounds, both superconducting and non-superconducting, in an unexplored system."

Jan 1, 1996

By Robert E. Schock, Eric J. Risberg

"Less than 20,000 years ago, the last of the glaciers retreated from the Chicago region. They left behind sheets of glacial clay till underlain by dense, over-consolidated till (“hardpan”) below which is the limestone bedrock, found about 100 ft (30.5 m) below street level. The most notable feature in this profile is the unusually soft clay till that has historically been called “Chicago Blue Clay.”But the founding fathers of Chicago really didn’t care about what was under the ground. They recognized the importance of the city’s location as a potential trade and transportation hub. With access to the East through the Great Lakes and access to the West through the Mississippi River system, the viability of the city was evident. Chicago’s population grew rapidly. The city continued to grow through the Civil War years, but was dealt a devastating blow in 1871 by the Great Chicago Fire, leaving the city in ruins. The Birth of the SkyscraperAfter the cleanup of the Great Fire came the first real building boom in Chicago’s history. During this era, buildings were generally founded on shallow footings bearing on sand or clay. Many multistory buildings were constructed between 1880 and 1890 on spread footings. The first tall buildings were constructed with load bearing masonry walls. These early tall buildings suffered significant settlement as the soft clay underwent consolidation.The Home Insurance Building, built in 1885, was 12-stories tall and is generally acknowledged to be the first “skyscraper” in the U.S. It was the first building constructed with an iron skeleton frame instead of load bearing masonry walls. Spread footings were used under the interior columns in an effort to better distribute the loads, but the building still experienced large settlements.Construction began for the Monadnock Building in 1891. The 17-story building was built using load bearing walls 7 ft (2.1 m) thick, supported on rail-grillage footing foundations. When completed in 1893, the Monadnock Building boasted the title “World’s Largest Office Building.” The total building settlement over the past 125 years has been measured at over 20 in (0.51 m). The engineering community in the late 19th century observed settlement, but did not yet understand the process of consolidation of the soft clay beneath the city. During this time, many of the new buildings required structural repairs during and after construction; the problem was especially acute in buildings where highrise towers joined lower podium structures."

Jan 1, 2016

By E. K. Stanek

This report contains results of two major efforts related to electrical transients on mine electrical power systems. The first area concerns the use of digital computers to model mine electrical power systems and predict transients or duplicate field recordings of transients. Two existing general purpose circuit analysis programs were used. The first was the TRW Engineering System Simulator or TESS. The second was Electronic Circuit Analysis Program or ECAP. TESS proved to be superior to ECAP in several important characteristics, including system size limitations and modeling nonlinear elements. The second major topic covered in this report is the evaluation of commercially available surge suppression devices. These devices were found to be quite acceptable and guidelines for the selection and placement of surge suppressors were included. The final important item is a listing of the worst-case transients, from a design point of view, for ac and de utilization systems and ac distribution systems.

Jan 1, 1979

By I. Masters, K. Buban, M. Faris, M. Antonio, M. Collins

"AngloGold Ashanti Brasil, with assistance from Sherritt International Corporation, has recently commissioned a new autoclave for the pressure oxidation of refractory gold feeds at their Corrego do Sítio operation in Brazil. Design of the new plant, including feed acidulation, pressure oxidation, oxidized solids washing and solution neutralization circuits, was based on the results of test work conducted by Sherritt at their pilot plant in Fort Saskatchewan, Alberta. This paper describes the results of the pilot plant study as well as highlights of the design exercise.INTRODUCTIONAngloGold Ashanti Brasil (AGA Brasil) has recently commissioned a refractory gold pressure oxidation plant at the site of the original São Bento operation in Brazil. The design of the São Bento pressure oxidation facility was based on Sherritt technology; Sherritt carried out the original process development test work in the mid-1980s, provided a process design package and detailed specifications for critical pressure oxidation equipment and participated in the training of operators and commissioning of the plant. The São Bento plant was operated between 1986 and 2007, when the original ore body was exhausted (Silva et al., 2004). AGA Brasil purchased the facility from Eldorado Gold in 2008, with the intent of refurbishing the plant to process refractory gold concentrates produced from the nearby Córrego do Sítio mining area.Sherritt International Corporation has a long history in the development and application of commercial pressure oxidation and pressure leaching processes. Sherritt’s development of technology for the pressure oxidation of refractory gold ores and concentrates commenced in the 1980s in collaboration with Homestake for application at the McLaughlin project in California. This was followed by several commercial applications in Canada, Papua New Guinea and Brazil (Berezowsky et al., 1991). More than thirty pilot plant campaigns investigating the pressure oxidation of refractory gold ores or concentrates have been conducted by Sherritt since the 1980s, and projects with Sherritt contributions to the process development studies and/or engineering design account for about half of the commercial plants that have operated to date with this type of process (Collins et al., 2011a; 2011b)."

Jan 1, 2012

By Clark D. Harrison

This paper compares the ash slagging potential of Illinois No. 6 Seam coal: as raw coal; as commercially cleaned coal processed in a baum-jig plant; and as coal cleaned to a reduced ash specification at the Electric Power Research Institute&apos;s Coal Cleaning Test Facility. The comparison is based on: ? ASTM ash fusibility data ? A slagging index ? Gravity fractionation analyses of critical mineral matter compounds ? Comparative pilot combustion tests. The first three grounds of comparison are laboratory data; and the final comparison involves burning approximately 15 tons of each coal at CONOCO&apos;s 1.5 MBtu/hr (440 KW) test combustor. The evidence of these .four comparisons indicates that lowering the ash specification of coal before combustion can significantly improve the ash slagging characteristics of Illinois 90. 6 Seam coal.

Jan 1, 1984

By William R. Jones, Robert M. Hernon

This report on the Central mining district of New Mexico is the partial culmination of an intensive U.S. Geological Survey effort dating back some 30 years. Robert M. Hernon went to Silver City in 1948 to finish a detailed restudy of the district that had been started in the thirties by Samuel G. Lasky. He was joined by William R. Jones in 1951, and Jones took over as project chief when Hernon resigned to do consulting work in 1953; it was under Jones' guidance that most of the work was brought to completion or nearly so ( 17, 22-24, 26-30). Hernon returned to the Survey in 1958 to work in .the southern Appalachians. Early in 1965 Jones urged that Hernon be reassigned to the Silver City project to help complete the Professional Paper report on the ore deposits of the Santa Rita quadrangle as well as to take over preparation of the report on the Central district for the Graton-Sales volume. This reassignment was approved, and Hernon began work on the present report. By late June he had completed most of it in draft form, and on June 28 Jones and Hernon left Denver for a short trip to Silver City to fill in a few gaps and to reacquaint Hernon with activities in the district, which he had not visited for 12 years. Late in the afternoon of June 29, 1965, as Bob and Bill were 85 miles short of their destination, their jeep collided head-on with a truck that was attempting to pass another vehicle in a cloud of dust. They both died instantly. As the most recent surviving member of the Silver City project (1958-1962), I was given the honorable though rather sorrowful task of putting the Hernon-Jones report "in shape" for publication. Fortunately the manuscript was already in good shape, so that the task has consisted of little more than minor reorganization and editing, and of preparation of the illustrations, abstract, and bibliography. The sections on wall-rock alteration had been left for Jones to complete in the light of his recently intensified interest in alteration geochemistry (25), and it is in these sections only that. the report may fall short, for they have been filled in from a 1958 manuscript by Jones on the ore deposits of the Santa Rita quadrangle that he intended to revise considerably. The shortcomings, however, are largely in the interpretation, not in the field data. As a brief but accurate summary of what was known about the geology of the Central mining district in 1965, this report stands as a fitting testimonial to the scientific dedication of two exceptional men.

Jan 1, 1968

Jan 1, 1913

By R. D. Carnahan, G. A. Stone, R. J. Arsenault

An experimental technique has been developed for carrying out a dynamic tensile stress-strain test in which plastic strain is measured continuously throughout the microstrain region extending through the macroflow region to total deformations of 5 pet. The tests were carried out on niobium, samples having interstitial impurity levels of 160 and -800 ppm at temperatures ranging from room temperature down to 100°K. A band spectrum of activation energies was obtained from calculations based on the measured activation volumes and temperature dependence of flow stress. The inability of a single rate-controlling process to predict such a phenomenon has led to the proposal that several sequential rate-controlling dislocation mechanisms are operative in the preyield micro-strain region. These are thought to be: the motion of geometrical kinks, the formation of double kinks in edges, and finally in the macrostrain region the formation of double kinks in screws. In less pure niobium the effect of interstitial impurities is shown to be dominant in the microstrain region, suggesting that a fourth probable mechanism is overcoming interstitial barriers instead of geometrical kink motion and the formation of double kinks in edge dislocations. THE principal fundamental aim of most mechanical properties studies of crystalline solids is to determine the dislocation mechanisms responsible for the plastic behavior. The extension of such studies to the region of preyield microstrain behavior has received renewed attention in the past few years as the details of macroscopic flow behavior have become better understood. For the most part, microstrain studies have been carried out using one of two variations of a single experimental technique.1 The first method involves loading the sample at a constant extension rate to a predetermined stress level (less than the macroscopic yield stress), instantaneously unloading, and then determining the extent of plastic deformation to a sensitivity of 10"6. The microscopic stress-strain curve is then constructed from the results of a repeated series of such individual measurements, each of which involves loading to an incrementally higher stress level, by relating the accumulated plastic microstrain for each step to the maximum applied stress in that step. The second variation, also carried out by step-wise increases in stress, measures the total strain to a sensitivity of ~10"6 and relates the maximum stress to the area of closed hysteresis loops that are generated under certain conditions (namely, prestrained samples). The foregoing methods have yielded interesting information about the nature of preyield deformation and plastic response to stresses below the yield stress, but they offer certain disadvantages for studying the dynamic behavior of dislocations. In the first method it is physically impossible to specify a plastic strain rate inasmuch as the test sample is reexposed, as it is loaded to its maximum stress in a particular step, to lower stresses at which flow will take place. The strain corresponding to a given stress level on the stress-microstrain curve thus generated will then always be greater than that at the corresponding stress level of a truly dynamic test carried out at the same extension rate. The second method has been used to obtain correlations with dynamic macroscopic flow parameters by applying dislocation damping theory to the hysteresis loop areas.2 The approach has had some success but suffers in that only samples that have been prestrained a few percent can be studied. Although the stresses

Jan 1, 1968

By P. K. Parhi

The extraction of nickel has been carried out by the hollow fiber membrane technique using D2EHPA as the mobile carrier from the manganese nodule leach liquor after separation of Cu(II), Zn(II) and Co(II). The experiments were designed according to central composite design (CCD), which is a response surface methodology. The process parameters used for the experimental design were: pH, concentration of D2EHPA in the membrane phase, flow rate and H2SO4 concentration in the strip solution. Based on the analysis of variance, a reduced quadratic model was found to best fit the experimental data. The process parameters were optimized to maximize the nickel flux and the optimized conditions were flow rate: 630 mL/min; pH: 6.37; D2EHPA: 1.15 mol/L (1,150 mol/m3) and H2SO4: 2.39% (430.2 mol/m3), for a maximum nickel flux of 7.08 x 10-5 mol/m2.s, which was in good agreement with the actual Ni flux of 6.99 x 10-5 mol/m2.s.

By Jochen Petersen

Design and operation of heap leach processes are still largely based on,operator experience and rule of thumb. Although considered a low-cost, low-tech route for mineral extraction, the underlying physical, chemical and biological processes are actually rather complex. Numerous heap leach models have been devised over time, but the majority of these tend to simplify the true process and are of limited use in practise. The modelling approach presented here combines the more conventional reaction-diffusion model with models accounting for equilibrium reactions in solution, bacterial growth kinetics, complex reactions schemes, gas flow, heat conservation, etc. One particular model application is discussed in the context of developing a novel high temperature heap leach processes using thermophile micro-organisms. The complexity of processes such as this can only be appreciated with the aid of a systematic model. For the designing engineer an accessible, personal computer based model should be an indispensable tool for the design and optimisation of efficient heap leach operations.

Jan 1, 2002

By G. Bezuidenhout, N. C. Steenkamp

Buying centres are the first point of contact that determines whether ore will be considered as having sufficient provenance to be considered ethically sourced. The information that needs to be captured on the blockchain platform ranges from reports on in-loco inspections and audits of mining and purchase sites. This will guide passive and active monitoring of mining activities, trade-offs for identification systems, including biometrics for the registration of artisanal sellers, scrutiny on the selection of security measures and companies for buyer centres and stockpiling warehouses, evaluation of active and passive infrastructure security, and remote monitoring applications. Assistance with selection and training in geochemical testing instruments to determine the grade of ore material or concentrates and sorting, on-the-ground investigations, guidance on monitoring methods from stockpile and packing area along the transport route to the final destination are required.

Jan 1, 2023

By F. Calizaya

A booster fan is an underground ventilation device installed in the main airstream to handle the total quantity of air circulated to one or more working districts. It is installed in a permanent stopping and equipped with airlock doors, a monitoring system and interlocking devices between the main fan and the booster fan. When adequately installed, a booster fan can be used to reduce the main fan pressure, reduce leakage and decrease the power consumption. However, an inadequate installation can increase the likelihood of mine fies and recirculation of air contaminants. This study identifies hazards associated with the operation and maintenance of booster fans. It analyzes the accompanying risks and recommends control measures to reduce those risks to acceptable levels. The ventilation network of an existing coal mine was updated to include a booster fan. The hazards associated with the operation of this fan were identified, the risks analyzed and the esponse to each failure mode established.

Mar 1, 2014

By Jonathan Peck, Carl Hendricks

"Global Positioning Satellite (GPS) based positioning and navigation systems have been recently developed and implemented by AQUILA Mining Systems Ltd. on blast hole drills and electric cable shovels in Canadian open pit coal and iron ore mines. These systems enable the location of the drill bit or the shovel tracks to be accurately determined in three dimensions. The position of the drill or shovel is displayed to the operator via a real-time, Moving Map Display (MMD) on an LCD-VGA screen. The MMD allows the operator to accurately navigate the drill from blast hole to blast hole or maintain a desired shovel grade or face position, with respect to displayed bench features. The maps for the MMD are downloaded from the mine office via laptop or radio link as required or as mining plans change.To obtain reliable, accurate and real-time3D positions of mobile mining equipment, proven GPS technology has to be utilized. The GPS components need to operate reliably under the severe environmental conditions that exist on board mobile mining equipment. In addition, they have to contend with varying pit geometry’s and satellite configurations, with little or no performance degradation. These issues were initially examined in December1993 during a feasibility project between AQUILA and Gregg River Resources Ltd., in relation to implementing GPS systems on blast-hole drills.To achieve certain design objectives, AQUILA Mining Systems Ltd. has developed navigation systems for cable shovels and blast-hole drills based around off-the-shelf, high precision GPS components. These systems utilize the AQUILA Advanced Monitoring Platform (AMP), to display graphically, via the MMD, shovel grade and drill position to the operator to within ±12 inches of design coordinates. Production prototypes have been installed on a Marion 301 cable shovel and a Bucyrus-Erie49-R Series III drill at the Fording River Mine in August, 1995, at the Wabush Mine on a Bucyrus Erie 190-B shovel in June, 1995, and on a GD120 drill at Gregg River Resources Ltd. in January, 1996. All these systems have undergone field trials to test system components and functionality’s under actual production conditions. This paper will discuss these GPS-based positioning and navigation systems in subsequent sections."

Jan 1, 1997