Search Documents

By J. S. Peterson

Occupational noise-induced hearing loss (NIHL) has been recognized by the National Occupational Research Agenda (NORA) as the most common job-related disease in the United States. Roughly 30 million workers are exposed to excessive noise levels or toxins that are potentially hazardous to their hearing. The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR)is investigating noise controls to reduce operator overexposures caused by haul trucks used in underground metal/non-metal mines. To identify the most significant contributors to the overall sound level, Source Path Contribution (SPC) analysis was conducted. Noise dosimetry and time-motion analysis were also conducted to quantify operator noise exposure. SPC analysis determined that, under high idle conditions, a source near a hydraulic pump mounted to the rear of the engine and the engine cooling fan were the major noise sources. The time-motion/dosimetry analysis showed that the operators accumulated more than 90% of their noise exposures while they were hauling ore to the dump site and traveling back to the load site unloaded.

Jan 1, 2012

By Alfred Bellows

The objective of this contract is to design, build and demonstrate a support system to improve roof control in the entries of longwall mines. The objective of this phase has been the detailed design of such a system and the selection of a test site in which to perform the pilot demonstration. The result is a complete set of detail drawings or specifications which define the three major components of the system. The Gate Support is a variation of a face chock which has an extended canopy and additional hydraulic legs to protect the region of the face-entry intersection. The Entry Support is a steel beam and hydraulic prop set which is reusable and serves to support the first 100 or more feet of entry inby the longwall face. The Transporter is a bolter-like vehicle with a crane used for installing and retreating the beam sets. The test site selected is CF&I's Allen Mine in Colorado. They presently use simi¬lar steel beams and expect the FMA support system to be more effective as well as recoverable. It is recommended that the completed drawings be used to build a prototype system and test it first in a remote section of the mine and then in the active longwall tail entry.

Jan 1, 1978

By P. H. Derbyshire

The use of continuous flight auger piles has increased significantly in the U.K. to such an extent that it is now the most widely used method of constructing small diameter bored piles. This paper describes the improvements in equipment, techniques and particularly monitoring that have led to this growth. A review of the equipment in use describes how purpose built self erecting machines have been generally adopted. Improvements in ancilliary equipment are described. Concrete has almost completely replaced grout and techniques have been developed to extend the length of reinforcement that can be placed. Leading specialist contractors have developed instrumentation to monitor the construction of the pile (in terms of time, depth, torque, concrete pressure and flow) and keep a record for checking. A further significant development of this monitoring by means of sensors at various levels in the auger stem is described. The results obtained from this monitoring are reviewed and future developments discussed.

Jan 1, 1989

By J. M. Provost

1. Estimates have been made for eight coal beds in Marion County, but only the Pittsburgh is important from a production standpoint at this time. The Pittsburgh bed has the largest recoverable reserve, and the Sewickley is second in importance. 2. Known measured and indicated reserves thickness of 14 inches and on 1,800 short tons estimated at 3,141 million tons, as of January lion tons is in beds 28 inches and more thick in all beds, based on a minimum per acre-foot of coal in place, are 1, 1955. Of this total, 2,983 mil-Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By T. A. Rickard

The key-note of good writing, as of good manners, is B natural. Sincerity is the first requisite for effective writing. When a man says what he knows or believes, he is likely to be interesting, because each human being possesses an individuality, a point of view, or a range of sympathy that makes him different from his fellows. To say or to write what you do no6 think, for the mere sake of talking or writing, is a verbal exercise that must be performed with extraordinary skill if it is to be attractive. Affectations are rarely attractive, rarely effective. To be natural is to be yourself, not a poseur; to give the reader the best of yourself, instead of re-warming the baked meats of yesterday. Quotations-which are second-hand thoughts-will serve occasionally when the thing you want to say has been said so well by another that it would be waste of energy to try to say it better; but, as a rule, the utterance of the writer himself is more interesting than the quotation, because the writer brings something of himself to bear on the subject, and for the moment is more in touch with the reader than any dear departed author. Therefore, say things as best you can in your own way, neither in borrowed words nor in the phraseology that mimics another. Write as if you were speaking to a person whom you desire to persuade or convince. You will then write better than you speak, because, in the first place, you can be more deliberate, and, secondly, you can revise what you have written. Speaking and writing are similar mental acts, with a difference: the difference between eating food raw and eating it cooked. Some kinds of food gain nothing by being cooked; likewise some kinds of utterance are not bettered by being written down first; but most expressions of thought, especially

Jan 1, 1931

By Graham Holmes, John Starkey

"The Kinross Kubaka Project is a gold mine located in the Russian Far East. The grinding circuit, comprised of a 6.1 m diameter x 2.74 m long SAG mill and a 4.1 m diameter x 5.5 m long secondary ball mill in closed circuit with cyclones, was built using SAG Power Index and Bond Ball Mill Work Index testing to determine the grinding energy requirements. Extremely cold climatic conditions and the need to keep heated space and capital costs to a minimum, dictated a grinding circuit with no in-circuit crusher and no conveyors external to the mill. High energy requirements for both the SAG mill and the ball mill were correctly predicted and have allowed grinding production tonnage forecasts to be met. Design test data and production results are given.INTRODUCTIONIn 1995 Davy International Canada, now Kvaerner Metals E & C, was commissioned as the Engineer and Project Manager for the Omolon Gold Mining Company, to design and construct a gold extraction plant for the Kubaka gold deposit, located in the Russian Far East. This deposit had been studied extensively in Russia during the exploration phase and a Feasibility Study was completed in 1993 by Kilborn who visited the site twice during that year to inspect facilities and to take metallurgical test samples. More samples were taken in 1995 to check ore hardness variability, as part of the final design program by Davy.The client’s objective in designing the Kubaka grinding circuit was to achieve design tonnage at all times, even when milling the hardest ore zones in the deposit. Since the samples taken in 1993 were taken as composite samples, it was necessary to take additional samples in 1995 to determine the extent of the variability. Six samples were sent to Canada for SAG Power Index (SPI) testing. Five of these were combined as a composite open pit sample, while the sixth sample was taken from the site adits as a composite sample to represent undergound ore. These two composite samples were tested to determine the MacPherson Autogenous Work Index for comparison with the SPI values."

Jan 1, 2001

By Richard K. Sandaas

Start Date: April 4, 1988 Completion Date: Dec. 29, 1989 Contractor: SCI Contractors Past and present transportation centers will come together at International District Station, located at the south entrance to the tunnel next to the turn-of-the-century Union Station train depot. The area will bustle once again with activity as commuters and visitors converge on the modern transit station at the edge of Seattle's International District. Buses coming from south Interstate 5 and Interstate 90 will enter the tunnel through this station. [ ] International District Station is an open-air station, 1,060 feet long and 82 feet wide (about 15,400 cubic yards of concrete were used to build the station). A concrete lid over the southern portion of the station staging area is held in place by 131 support piles. The station will include entrances on Jackson Street and King Street. Union Pacific Realty is planning to build an office and retail complex upon the lid. The station also has an international flair. Symbols of the Chinese zodiac will be etched into the station plaza floor. The station platform walls will be lined with large steel panels embellished with designs in origami?a Japanese folded paper art form. [ ]

Jan 1, 1990

By Jacob Chacko

The Izmit Bay bridge, a 3-km-long suspension bridge crossing of Izmit Bay, Turkey is planned to be constructed in one of the most seismically active places in the world. The site, which has the potential to experience significant earthquakes associated with the relative motion accommodated on the North Anatolian Fault, is underlain by deep deposits of soft soils, and areas of unstable and liquefiable soils. Characterizing the seismotectonic setting, foundation soil conditions, potential fault locations, as well as other geohazards was a critical component for the project concessionaire to finance the project and obtain meaningful bids for bridge design and construction. Given the Build Operate Transfer (BOT) funding mechanism, executing this work in the least possible time was critical to the concessionaire?s financing scheme. Fugro was retained to provide geotechnical, geological, and seismological evaluations for the project region, and to generate data for contractors to develop reliable designs and bids. The uncertainties in these data made it difficult for the BOT concessionaire to finance the project and tender Bridge design and construction. The investment in an early and comprehensive site characterization program to evaluate and quantify those uncertainties allowed the concessionaire to save schedule, provide a robust bid basis to bridge contractors, and persuade banks to finance what was perceived to be a relatively high risk project.

Jan 1, 2011

By M. J. McLeod, D. R. Lux, R. P. Taylor

"The Mount Douglas Granite constitutes the eastern part of the Saint George Batholith and contains the youngest, most differentiated phases of the batholith. It also contains extensive endogranitic, low-grade. Sn- W-Mo-bearing sheeted vein systems. Early phases of the Mount Douglas Granite are coarse- to medium-grained, seriate granites that represent the slowly cooled carapace of the intrusion. Late phases are medium- to fine-grained, equigranular and porphyritic granites that were accompanied by repeated and widespread fracturing of the carapace and injection of mineralizing fluids. These granites represent a highly differentiated suite with ""A "" type affinities developed in a ""within plate"" transitional to ""syn-collision"" tectonic setting. 4oAr/ 39Ar dates for biotites from the various phases indicate emplacement circa 367 Ma.The linear distribution of some phases in the Mount Douglas Granite and the systematic orientations of sheeted veins along tensional fractures indicate structural control on granite emplacement and vein distribution. This type of relatively passive endogranitic mineralization is unique in the granites of southern New Brunswick and contrasts markedly with highly fluidized systems operative elsewhere in the area. IntroductionInvestigation of Sn-W-Mo occurrences in New Brunswick has shown that most of this mineralization is associated with late, highly differentiated phases of post-orogenic (Acadian) granitoid magmatism that occurred during Devonian and Early Carboniferous time (Ruitenberg and Fyffe, 1982; Taylor et al., 1988). The polymetallic Mount Pleasant Sn-W-Mo deposit (Ruitenberg, 1967, 1972; Kooiman et al., 1986)and the Burnt Hill W deposit are two orebodies of this type in New Brunswick. Numerous smaller deposits associated with these granitoid rocks in southwestern New Brunswick have been documented in previous investigations (Ruitenberg, 1967, 1968; Ruitenberg and Fyffe, 1982; Taylor et al., 1985; Lentz, 1985)."

Jan 1, 1988

The geologist is often called upon to give judgment on the possibilities of reviving a former mining field presumably worked out as far as the evidence then available indicated. From time to time, scarcity and consequent high prices of metals has led to there-examination of many old fields. The possibility of resuming investigation on them where the practical miner ceased work, even where he had the aid of the trained geologist, has long since disappeared.Means of access to mines have been removed and water fills the workings. Hence an indirect mode of attack becomes essential.This method depends mainly on past history, and may be described as a reaching out by faith supported by shrewd guessing from the known to the unknown. Apart from whatever general intelligent observations may be made in situ of the evidence of former mining activity, the method depends largely on the examination of the past history of the field as revealed in the official records, company reports, plans of underground workings, local newspaper accounts, and the testimony of practical miners formerly employedon the field, the' reliability of which has to be carefully sifted. The matter derived from the examination of these sources must next be rigorously collated and correlated where possible. When the review of all individu!1l features and aspects has been completed, tentative and speculative conclusions may be drawn which, though not verifiable before the event, will usually prove to be more serviceable guides in exploratory operations than mere "blind stabbing."As an actual illustration of what is involved in the mode of procedure outlined above, the following is the description of an investigation in which the writer took part.In 1937, during the course of the Commonwealth Aerial, Geological and Geophysical Survey of Northern Australia, a detailed geological investigation was undertaken of the Croydon gold field, situated near the south-eastern. extremity of the Gulf of Carpentaria in North Queensland.The history of the field briefly is as follows: It was discovered in 1885, reached its peak of production 1896, declining thereafter till 1906, when operations ceased. The total production was about 1,000,000 ounces of gold bullion, containing approximately 40 per cent. of silver. The gold bullion was won from flat-dipping quartz reefs, which yielded an average of 2.oz. to the ton, and the maximum depth to which production occurred was 500 feet. Subsequent prospecting below this depth failed to locate further ore.In consequence of the inaccessibility of the mines and the almost total masking of the' surface by alluvium, the investigation of future possibilities became largely an. office ,study, which was conducted under the following headings:-1. Recording of factual data of each mine separately.

Jan 1, 1950

By D. F. Hambley

This report documents the work carried out by Engineers International, Inc. and its subcontructor, W. G. Pariseau, in order to develop a design manual for ore passes for open pit mines. The work included an extensive information search, novel analyses in rock flow theory, cost and time estimation for shaft and raise construction methods, and development of design criteria for the are pass proper, dump point, and draw point.

Jan 1, 1983

By Robert H. Peters

This Bureau of Mines report describes several significant problems associated with absenteeism among underground coal miners. The vast empirical literature on employee absenteeism is reviewed, and a conceptual model of the factors that cause absenteeism among miners is presented. Portions of this model were empirically tested by performing correlational and multiple regression analyses on data collected from a group of 64 underground coal miners. The results of these tests are presented and discussed.

Jan 1, 1987

By Howard A. Perko, M. Mae Benvenga, Heather H. Trantham

Displacement of soil and groundwater during helical pile installation can produce excess pore water pressures (PWP) in fine-grained soils. Pore water pressure reduces effective stress in the soil immediately adjacent to the helical pile shaft and near the helical piles. Previous studies have shown generation of PWP may affect the capacity to torque ratios of the helical bearing elements. Large diameter helical piles that generate much of their torque and capacity from shaft adhesion are affected by PWP and therefore exhibit significant pile "freeze" after installation. Computer modeling is used herein to evaluate PWP immediately adjacent to helical pile shafts during installation in various soil types. The models show the degree and distance from the shaft that is influenced by PWP during installation and the amount of time required for the PWP to dissipate. Pile freeze has been measured on several project sites by re‐torque measurements. These re-torque data are compared with computer modeling and correlations between saturated hydraulic conductivity and dissipation time are presented and discussed. INTRODUCTION Helical piles are full-displacement piles, meaning installation does not produce drill spoil. Soil is displaced laterally as the pile progresses into the ground. This displacement of soil causes an increase in PWP, which reduces adhesion between the pile and the soil. For helical piles with small-diameter shafts, adhesion contributes little to the overall capacity and torque of the pile, so PWP changes are not typically considered in determining pile capacity. In modern construction, the use of larger diameter helical piles has become very common. For large-diameter helical piles, changes in PWP immediately adjacent the shaft can be quite large during installation. Increased pore water pressure and reduced adhesion can have a temporary effect on pile capacity and installation torque.

Jan 1, 2018

By Jaan Kiusalaas

This report is a self-contained User Manual for a computer program called SPASID -- Subsidence Prediction and System Identification. The program has two primary functions: (i) Precalculation of ground movements due to underground mining operations using the influence function method; (ii) Computation of influence function and site parameters from measured displacements. SPASID is written in FORTRAN and consists of four modules: (i) Preprocessor Module that prepares and maintains surface and mine data bases; (ii) Subsidence Computation Module that predicts movements of the surface; (iii) System Identification Module which is used to calculate the optimal influence function parameters, and (iv) Postprocessor Module for generating graphic displays of subsidence data. The last module is somewhat machine dependent but has internal documentation to indicate potential changes. All of the modules may be run in either batch or interactive mode. The manual does not assume previous knowledge of the influence function method or programming competence.

Jan 1, 1983

By David G. Dixon, Maziar Eghbalnia

"Gold and silver nanoparticles (NPs) were deposited on pyrite at ambient temperature from colloidal solutions prepared by reduction of hydrogen tetrachloroaurate or silver nitrate by sodium sulfide or sodium tetrahydridoborate. The nanoparticles were characterized using Ultraviolet-Visible (UV-Vis) spectroscopy and the experimental spectra were fitted using Mie - Gans modeling. The modified pyrite was investigated using Electrochemical Impedance Spectroscopy (EIS). Electrodes were prepared from both natural and modified pyrite samples and were modeled using an equivalent circuit (EC) based on the EIS data. The comparison of the results revealed a decrease in charge transfer resistance for the ferric ferrous redox couple associated with the modified pyrite. From this behavior it is concluded that the electronic transport between the nanoparticles and the electrode surface over distances in nanometer scale is enhanced. Nanoparticles below a certain size act as quantum dots due to electronic confmement. Decreased charged transfer resistance at the nanometer scale may be caused by electron transport through tunneling mechanism via quantum dots.IntroductionIn recent years, considerable attention has been focused on the synthesis and study of Metal nanoparticles due to their potential applications in the fields of physics, chemistry, biology, medicine, material science and their interdisciplinary fields[!]. When material is nano-sized, the physical properties deviate markedly from those of bulk material, however, this effect is highly dependent on the particle size, interparticle distance, and morphology of the nanoparticles [2].An extremely small region of space defmed in a semiconductor material in order of nanometers is called a quantum dot, a term coined by Reed [3]. The three dimensional confinement of quantum dots can change properties of the excitons in comparison to free excitons in a bulk material [4]. Nanoparticles behave electronically as zero-dimensional (restricted in all three dimensions) quantum dots when the de Broglie wavelength of the valence electrons and the particle are in the same size range.As Reed [3] explains electrons confined in a plane have no freedom to move the third dimension. Those confined in a quantum wire are only free to move in one dimension, and those confined in a quantum dot are not free in to move in any dimension. An electron inside a cube of material IO nm on a side is confined to a point."

Jan 1, 2012

By Albert H. Fay

Through the hearty cooperation of the State coal-mine inspectors, the bureau is able to present in this paper a a complete statement of the coal-mine fatalities occurring throughout the United States during the calendar year 1919. The reports received from the inspectors for the year just closed show a reduction of 10.58 per cent in coal-mine fatalities as compared. with 1918, while in 1918 the reduction was 4.3 per cent from 1917 figures. The total number killed was 2,307 in 1919 and 2,580 in 1918, a reduction of 273. There was a decrease of 128, or 25 per cent, in fa tali ties resulting from mine cars and locomotives, and a decrease of 198, or 15 per cent, in the fa tali ties due to fall of coal or rock. Surface accidents show a decline of about 25 per cent as compared with the previous year. There were, however, increases in accidents due to gas and dust explosions and also explosives. There occurred during the year nine disasters in which five or more men were killed, representing a total of 201 fatalities. The worst disaster of the year was the one occurring at the Baltimore Tunnel No. 2, Wilkes-Barre, Pa., resulting from the explosion or burning of a number of kegs of powder, by which 92 lives were lost. This disaster emphasizes the need for stricter regulations relating to hauling men and explosives into the mine at the same time. The question of whether electricity was responsible or not does not affect the consideration of the various dangers which arise in underground transportation and handling of explosiveB. At best the handling and hauling of explo.sives is hazardous and such being the case, no one, other than the necessary attendants, should be permitted to ride in cars or cages transporting explosives. As a result of this disaster, the report b of the coroner's jury to the governor of Pennsylvania brings out some important dangers to be avoided in the use and transportation of explosives.

Jan 1, 1920

The dynamic response of holdup in a continuous ball mill has a direct influence on the rate function of grinding kinetics and is useful for predicting the variation in the size distribution of the finished product with time.A model was proposed involving three interacting, completely mixed chambers and this was used to derive analytically the transfer function of the system, from which the unit impulse response and the unit step response of the holdup with feed rate were obtained.The theory was confirmed by comparing it with previously published experimental data for the residence time distribution of particles passing through a ball mill.

Jan 1, 1975

By S. M. Shelton, W. A. Calhoun, M. M. Fine, T. L. Johnston

"INTRODUCTION An extensive test program is in progress by the Bureau of Mines to determine ways and means of recovering ferromanganese-grade ore 6/ from the wide-spread domestic manganese and manganiforous iron deposits. Samples for testing were received from the Interstate Manganese Co. in northeastern Tennessee, 11 miles west of Mountain City and 10 miles southwest of Damascus Va. The ore deposit occurs in the residual material of the Shady dolomite 7/ as an unconsolidated mixture of hard and soft manganese oxides and clay.Numerous tunnels and pits have developed a large reserve of ore in an area of about 15 acres. One pit 250 by 50 by 20 feet is being mined by rower shovels. The ore is hauled to a washing plant for log-washing, hand-sorting, and jigging. Coarse concentrates from the washing plant are marketed without further beneficiation.ACKNOWLEDGMENTSThe authors wish to acknowledge the assistance of R. F. Fisher, who made the roasting and magnetic tests."

Mar 1, 1942

Minerals are vital to any industrialized civilization. Annually, the United States uses more than 4 billion tons of new mineral materials, or about 40,000 pounds per person-about half being mineral fuels and the other half metals and nonmetallics. Stable and economic domestic mining, mineral, metal, and mineral reclamation industries are essential to the economy. The value of United States energy and processed materials of mineral origin exceeds $200 billion annually. Although a number of minerals are imported, especially some designated as "strategic and critical," most U.S. mineral supplies are derived from the domestic mines and processing facilities that you will be seeing, reading about, and visiting as you use this visitor guide. We hope you enjoy your experiences. This pamphlet, a guide to mining and mineral operations that may be observed or visited and some other points of interest relating to minerals, is intended to aid tourists and students who are interested in mining. Some may wish to study our Nation's romantic past; others may plan to enter the minerals industry as a career; still others may have a primary interest in conservation practices. The pamphlet is also intended to aid State and local officials, Chambers of Commerce, and mining firms in answering some of the many questions of tourists and students.

Jan 1, 1977

The request for proposal from the U.S. Bureau of Mines outlined the purpose of this study in the following terms. "High grade near surface deposits are largely a matter of history. Most of the current mineral production in the united States is from large low grade ore deposits mined by large scale methods. It appears likely that exhaustion of near surface deposits and public resistance to open pit mining will tend to reverse the present trend toward open pit mining and lead to increased reliance on large scale underground mining. In view of the long lead time needed to improve basic technology, an in-depth study of the major underground mining methods is needed. "This study is intended to provide a systematic review and analysis of large scale non-coal underground mining technology with particular emphasis on current practices and problems, needed technological improvements, existing or potential environmental conflicts, and possible modifications or innovations that will assist in the satisfaction of projected national mineral supply requirements."

Jan 1, 1974