Search Documents

By William E. Shaw, Louis A. Carapella

Magnesium and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitionai point has been set at 2 25°C by Schmidl for single crystals, and at 250°C by Morel1 and Hanawalt² for extruded magnesium metal. In a recent X-ray investigation on poly-crystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional tempelature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheet† over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig I. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Har-greaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Har-greaves constant S, was obtained by the integrated or intermittent loading procedure. The authors6 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformatione 1 loads. These findings have been applicd

Jan 1, 1947

By K. Mikulash

"Agnico-Eagle Mines Limited is located at Joutel in North-Western Québec. The mine is about four miles north-west from the town on the left bank of the Harricana River. The present mining is 1,800 feet deep with an extensive geological development below this level.HISTORY The development of the ore body started sometimes in 1967 and then the operation ceased in 1969 and again reopened in 1973 due to higher prices of gold. During these periods of active development, a considerable metallurgical research has been done by different laboratories and research and design companies.The original capacities of the Mill differed as much as 30%. So did the concept of the ore treatment. The original design of the mill was for 200 TPD of ore with straight cyanidation. The problems with low gold extraction, high reagent consumption and poor filtration resulted in a decrease of the expected mill output to an initial 550 TPD with gold recoveries in the order of 40 to 60%.Although the studies and research work done on the ore varied, all of them had a common conclusion: a very fine grind is needed to expose gold. The mining method (sub-level blast hole mining) now provides the ore that differs from that on which the metallurgical test work was conducted and the original capacity calculations had been done.These variations in the concept consequently led to the conclusion that the size of gold is a determining factor for the process.Kilborn Engineering provided the original design with the Leslie Eng¬ineering completing the design. The metallurgical test work has been done by the Department of Energy, Mines & Resources, Lakefield Research of Canada, Kilborn Engineering and Sidam Incorporated.The new flotation section with secondary grinding has been designed and put into operation by the company in December 1975 with the results yet to be evaluated."

Jan 1, 1976

By Mohammad Noaparast, Babak Fotoohi

"Due to certain advantages in (semi-)Autogenous-Ball mill circuits in most of the high-throughput ore grinding units of mineral processing plants, much attention is paid to optimize the mill performance. Despite the maturity of the grinding mill mechanical design, there had been made less attention to the efficiency of the grinding media in the past. In this research, the possibility of establishing a relationship between liner/lifter wear rate and variations in the composition of the iron ore (from Chadormalu mine) is investigated.Measurements and determination of liner/lifter wear rates and patterns concluded in recognition of critical liner segments exposed to much abrasion during the ore grinding. After metallurgical analysis of liner materials and correlation of wear rate with the ore composition, the homogeneity in the metallurgical microstructure of the alloyed steel (such as the uniform distribution and amounts of the constituent phases) was determined as the most influential factor in the response of the liner/lifter to the variations in the ore composition. Magnetite with greater abrasion index than hematite, in finer particles, is responsible for additional abrasion of liners; hematite with greater work index exists in the mill with larger particle sizes, thus it could produce wear on liner parts with less tolerance to impact as is the situation for martensitic steels.INTRODUCTIONThe mineralization in Chadormalu plutonic iron ore deposit is consisted of mostly magnetite, hematite, martite, apatite, quartz and carbonates. The average composition of the ore is presented in Table 1. In the processing circuit, the gyratory crushed ore reduced to 30 cm would finally be the feed to three similar 32’ semi-autogenous mills in parallel processing lines. The pulp in the mill would have the characteristics mentioned in Table 2. The quality of the mill output has its direct effect on the downstream processes either physically or chemically (e.g. in cycloning or flotation respectively). In order to take advantage of optimum performance for these circuits, a close control of the ore grinding conditions is necessary; because any shortages in throughput, liner/lifter damage or changes in ore composition could bring the unexpected casualties. In this work, it has been attempted to find (possibly) a reasonable relationship between variations in ore characteristics together with liner quality and the amount of wear rate in different liner/lifter segments of a semi-autigenous mill. Liner/lifter segments are supplied by three different domestic steel making companies. The alloy structure of the liners/lifters is made up of pearlitic chromoly steel."

Jan 1, 2005

By M. A. El-Sohby

The paper describes some problems encountered with the foundation of a deep drainage caisson constructed on the Nile Bank in Cairo. The use of suction dredging while sinking the caisson led to a piping failure of the sandy soil in the base which was loosened during the process of pumping. A study was carried out to investigate the problem and a procedure was adopted to retain the stability of the caisson.

Jan 1, 2010

By A. Akerman, C. P. O’Connor, N. Vayenas

"Stereolithography is a well-known rapid prototyping technique in the manufacturing sector. Essentially, it is a three-dimensional printing process that produces plastic prototype parts from standard CAD files. At present, Canadian mining companies are not fully aware of the potential of rapid prototyping techniques (RPTs) for their production and mine design systems. Mining engineers and geologists attempt to visualize and understand the characteristics and layouts of orebodies on computer models, and in cases where it is decided to develop physical models, the process is time-consuming, based on simplified constructions. RPTs, such as stereolithography, can facilitate engineers and geologists to quickly, and with satisfactory accuracy, visualize sections of orebodies and evaluate alternative ore extraction techniques using 3D solid models.The research discussed in this paper is carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in collaboration with Inco Limited and the Integrated Manufacturing Technologies Institute (IMTI) of the National Research Council of Canada. The main objective with this research is to evaluate the applicability of state-of-the-art RPTs to underground hard rock mining systems. RPTs can play a significant role in accelerating the design and development process of mining systems."

Jan 1, 2006

By B. M. O'Harra

The residues resulting from the retort distillation of zinc ores have from 40 to 75 per cent of the weight of the original ore and contain from 5 to 15 per cent zinc . A rough estimate indicates that approximately 450,000 tons of residues are produced annually in the United States , containing about 36,000 tons of zinc . Besides the current production of residues there are at many smelter sites large accumulations from past operations which are available for treatment if this can be done profitably . In addition to their zinc content the residues contain much unconsumed coal , which has been carbonized during the distillation process , and those from most western ores also contain lead and silver . In this paper is summarized the information obtained in a survey , recently made by the Bureau of Mines , in cooperation with the Missouri School of Mines and Metallurgy , of processes which are in use or which have been suggested for the treatment of retort residues . The complete report of the survey is to be published as a Technical Paper of the Bureau of Mines .

Apr 1, 1923

By William R. Yernberg

The combined 79th Annual Minnesota Section of SME Meeting and 67th Annual University of Minnesota Mining Symposium was held April 11 and 12, 2006, in Duluth, MN. About 300 mining professionals attended, including engineers, executives, mining managers and suppliers, from throughout the United States and Canada. This year’s theme was “Success in the New World of Mining.” The SME Minnesota Section meeting included a keynote session, a special projects update, a general managers update and technical paper presentations. The University of Minnesota Mining Symposium program featured a panel discussion on Minnesota’s relationship with China. The combined meeting included a trade-show consisting of 64 booth spaces. Tradeshow demand exceeded expectations, and an additional 10 booth spaces were added in the registration lobby. Also included were an SME short course on pump basics and social events.

Jan 1, 2006

The combined production value of natural abrasives, which consist of tripoli, special silica stone, garnet, and emery, decreased in 1985. Shipments of processed tripoli increased slightly in quantity but decreased 6% in value, Production of garnet, an abundant iron-aluminum silicate, increased 24% in quantity and 20% in value. There was an 11% increase in the quantity and a 7% increase in the value of refined garnet shipped when compared with 1984 shipments, a new record high. Production of crude special silica stone decreased 10% in quantity and 14% in value, and shipments of finished special silica stone products decreased 85% in quantity and 68% in value. Both the quantity and value of special silica stone finished products sold or used were the lowest since 1981. Production of emery, an impure aluminum oxide, decreased 56% in quantity and 61 % in value of product mined and shipped. [ ]

Jan 1, 1987

By V. F. Parry

"INTRODUCTION During the war period the Bureau of Mines expanded its investigations on western coals principally in connection with Investigations of raw material resources for western steel production. Owing to the expansion of the steel industry, there was some concern regarding the availability of suitable coking coals; end because of the potential steel shortage, the production of sponge iron, using the lower-rank fuels, was considered. Work was conducted by the Bureau of Mines on exploration projects and on testing of coals both at the Central Experiment. Station at Pittsburgh, Pa., and at the Bureau of Mines Station at Golden, Cole.The results of these investigations are being published by the Bureau in several reports of investigations and technical papers. In making this resume of coal investigations, the work done by the Bureau of Mines at Pittsburgh in the Mining and Coal Carbonization Sections will be discussed and the investigations at Golden described in greater detail.INVESTIGATIONS OF WESTERN COALSThe Mining and Coal Carbonization Sections of the Coal Division, Bureau of Mines, under the supervision of A. L. Teeny es and J. D. Davis, respec¬tively, conducted many field investigations to locate and evaluate new sources of coking coals. Drilling explorations were made in Colorado, Wyoming, Utah, New Mexico, and Washington and revealed two important new reserves of coking coal. The first one studied was the Willow Creek bed at Kemmerer, Wyo., which was reported in 1945.3/ A recoverable reserve estimated at 11,200,000 tons was blocked out, and samples of coal were extracted for coking tests. The coking properties of the coal were not quite equal to those of Sunnyside coal, but it was indicated that a 50-percent blend of the Willow Creek with Lower Sunnyside will produce a satisfactory metallurgical coke based on Columbia steel standards."

Jan 1, 1948

By Luca de Sanctis

The analysis of piled raft foundations in layered soils may be performed by 3D finite elements or by approximate procedures. Among the latter, the code NAPRA (Russo, 1998) is based on the method of the interaction factors and accounts for soil layering by the so called Steinbrenner approximation. A comparison between the results of 3D FEM and NAPRA for some reference layered soil profiles shows that the approximation is fully acceptable for engineering purposes, provided the stiffness of the single pile is properly selected. The interest of the conclusion lies in the fact that the amount of work needed to model a practical problem by NAPRA is but a fraction of that needed by FEM modelling.

Jan 1, 2002

By A. J. Partos

The figures and tables referred to herein are presented in the Proceedings; Volume I, Pages 309 through 316. The 61-story One Liberty Place, at 315 m., is the tallest building 1n Philadelphia and was in 1987 the ninth tallest building in the world. One Liberty Place is supported on drilled piers socketed in heterogeneous metamorphic rock. Design load distribution was 40% on the base and 60% by shaft resistance. Drilled Pier G-10 supporting a T13-A type outrigger column was instrumented. There 1s no uplift load on the exterior outrigger columns. This column supports a 53,850 kN compressive load which includes a 13,440 kN windload. Table 4 presents experimental parameters from straight line interpolation of Mohr failure envelopes for the Wissahickon schist. Lowest values of cohesion (12,200 kN/m2) and angle of internal friction (19°) are at a 50° - 59° angle of foliation. Figure 3 presents a typical pier supported by shaft resistance 1n decomposed (D) and coreable (C) rock and by end bearing (B).

Jan 1, 1991

By Atsushi Shibayama, Toyohisa Fujita, Luo Lin, Toshio Miyazaki

A novel process is developed in this study for separation of tungsten and vanadium from a leach solution of tungsten alloy scraps. Specifically, a magnesium salt combined ammonium solution is employed to precipitate vanadium and impurities in the purification of the leach solution. This separates vanadium from tungsten by rejecting tungsten in aqueous solution. Finally, tungsten is recovered as the form of ammonium para-tungstate (APT). Vanadium is recovered as the form of ammonium meta-vanadate(AMV).

Jan 1, 2003

By K. S. Seljesater

SINCE the development of dispersion-hardenable lead-antimony alloys1 in the laboratories of the Western Electric Co., Inc., studies have been made of the effect of various third constituents on these alloys.2 This paper covers a study of the effect of small amounts of arsenic. This element is important since it occurs as an impurity in many commercial antimonial leads and the results obtained are particularly interesting as indicating a class of addition agents which exert a stabilizing effect on dispersion-hardened alloys. EXPERIMENTAL In order to-study the effect ,of increasing amounts of arsenic, a series of alloys were made up containing 1 per cent. antimony, and arsenic varying from 0. to 0.10 per cent., the balance Doe Run lead (99.997 per FIG. 1..-CHANGE OF MICRO-BRINELL HARDNESS WITH TIME OF 1 PER CENT. LEAD-ANTIMONY ALLOY. cent. lead). The alloys were cast into bars 1 ½ in. wide by ¾ in. thick and cold-rolled to about 1/8 in. thickness. Three samples of each composition were annealed 1 hr. at 225° C. and quenched in water. One set was aged at room temperature, one at 50° C., and the third at 100° C., the

Jan 1, 1929

By A. R. Denison

The area discussed in this report comprises a group of 38 counties lying in the northeast corner of Texas. It covers all, and extends beyond, the borders of what is commonly described as the East Texas Basin. It includes two major oil fields, Van and East Texas; two major gas fields, Bethany and Waskom; and a number of fields, both oil and gas, of lesser importance. All commercial oil production comes from beds of Upper Cretaceous age and almost exclusively from the basal member, the Woodbine sand. Gas is produced from both Upper and Lower Cretaceous beds with the newer production from the older beds. East Texas Field This field continued as in 1932 and 1933 to dominate the drilling and production situation throughout the oil business. A total of 3681 producing wells was completed in this field during 1934. This is an increase of 1215 over the 2466 producers completed during 1933. Total wells

Jan 1, 1935

By Wils L. Cooley

Two major grounding topics are covered: mine ground systems and ground-check monitors. Performance characteristics of ground-check monitors for high-voltage surface mine distribution cables and low-voltage underground mine trailing cables are evaluated. Over 20 commercially available monitors are studied to determine their utility. Several monitoring concepts are incorporated into an unusual monitor design, the prototype of which is described in detail. A comparative study of the effectiveness of several alternate methods of grounding surface mine equipment supports the system currently proposed by MSHA. An instrument design to measure earth voltage gradients is described, as well as an instrument design for measuring the effectiveness of dc haulage current return systems. An extreme analysis is made of techniques for measuring earth resistivity and resistance of safety ground beds. Electrolytic corrosion studies of earth electrodes are reported extensively also.

Jan 1, 1979

Established as a Society February 26, 1957 John S Bell, President Wayne E Glenn, President-elect Basil P Kantzer, Past President R E Howard, Vice, President M B Penn, Vice-President Everett G Trostel, Treasurer Joe B Alford, Executive Secretary 800 Fidelity Union Bldg Dallas 1, Texas

Jan 1, 1959

By Sebastián H. Troncoso

Open pit mine planning is normally based on the selection of an economic envelope that has been generated by the Lerchs & Grossman algorithm, which requires individual economic valuation of each block of a geological block model. The selected envelope, usually called Final Pit, is later discretized in pushbacks and benches, which correspond finally to the fractions that the production schedule will allocate in time. This planning methodology has been widely used by the mining industry in countless projects to exploit open-pit mines, however, in many of the deposits can be found some undesirable elements such as arsenic, phosphates, ash among others that tend to reduce the value of elements of economic interest, either by disrupting the processes of concentration or as deemed impurities that affect the quality of the final product. Thus, a fair amount of blending would be required to capture the real value of the ore body. The traditional approach under estimates a block value by penalizing the block value by the amount of contaminant even when at the mine a set of blocks is amine at a time. This paper proposes a methodology for computing cut off grades over time that would maximize net present value allowing blending that should fulfill a set of metallurgical constraints. Preliminary results show significant increases in value and reserves quantity, questioning the use of fixed cut-off grades in generating a production schedule when blending applies to fulfill a set of geometallurgical constraints. Finally, the model allows the authors to show the importance of having adequate planning tools that will lead to the ability to look at the potential economic value of a mineral deposit.

Oct 1, 2009

By Wayne I. van Drunick

"Energy balance modeling has recently been shown to be a competent tool in the estimation of SAG mill discharge rheology. Work performed by van Drunick and Moys (2001) validated the ability of an energybalance filter to estimate the slurry density from an operating SAG mill. The importance of rheological data is highlighted by several authors who show the effects on load behaviour and thus mill performance. Energy balance models were developed to account for the dynamic energies in the mill discharge sump. The models then made it possible to infer the mill discharge density. A sampling campaign was performed and the errors from the sump energy balance were within tolerable limits.Since the initial results were published, it has been decided to further develop the modeling techniques in order to focus on balancing the energies around the entire mill. The critical measurements for the energy balance will be the temperatures of all the streams entering and leaving the mill, including energy losses to the environment. Metso’s OCS© (Optimising Control System) currently controls the 3 SAG mills at Anglogold’s Mponeng Gold Plant (South Africa). The OCS has built-in Kalman filtering tools to effectively handle variances and noise in the models and the mill circuit data respectively. The new models are therefore constructed in the OCS platform, and will be run in parallel with Metso’s current modeling and filtering systems. The work is a collaborative effort between Anglogold, the University of the Witwatersrand and Metso. The benefits of energy modeling, compared to mass modeling, are that energy data are more accurately measurable than mass data. The inferred mill parameters can therefore be improved provided that a competent set of models is produced to process the (accurate) thermal measurements."

Jan 1, 2003

By R. E. Michelutti

"The Sudbury area environment became drastically altered commencing in 1871 with lumbering, repeated fires and early open roasting operations from 1887 to 1929. These combined factors had such a pronounced effect that approximately 24 square miles were totally denuded of any vegetation and 87 square miles were semi-barren to somewhat stressed.The two nickel producing companies in the area have reduced the sulphur dioxide emissions considerably over the years. Falconbridge Limited, alone, reduced sulphur dioxide emissions by 77% from 1971 to 1984.These reductions have resulted in improvements to the air, soil, lake and vegetation quality in the Sudbury area.INTRODUCTIONThe Sudbury area environment became drastically altered commencing in the 1870's with lumbering, repeated fires and early open roasting operations from 1888 to 1929. These combined factors had such a pronounced effect on the Sudbury environment that approximately 24 square miles (64 sq. km.) were totally denuded of any vegetation and 87 square miles (225 sq. km.) were semi-barren.Over the years, the Sudbury area environment has improved considerably. This has been due to emission cutbacks by both Inco Metals and Falconbridge Limited, coupled with industry, government and community reclamation programs. Before the improvements are discussed, a better understanding of the historical degradation is required."

Jan 1, 1986

By Claude Bazin, Patricia Obiang

"The slurry density (pulp percentage of solids) and the size of the grinding media are often used for the optimization of an operating ball mill. In many cases a change of ball size is made at the slurry density used with the original ball size. But is the optimum slurry density changing with grinding media size? Laboratory grinding tests were conducted to answer that question and results indicate that more than likely there is no need to adjust mill slurry density when adjusting the size of a grinding media in a ball mill. Full scale behaviour could be different because slurry density affects the slurry transportation through the mill and the classifier operation.INTRODUCTIONOre preparation begins with a fragmentation step that liberates valuable minerals or exposes mineral surface to the environment. The size reduction step of a mineral processing operation is energy demanding and the optimisation of this process should always be an objective for the plant metallurgists. Various approaches could be considered for improving the operation of a grinding circuit. For a close grinding circuit an adequate tuning of the classifiers operation may lead to substantial savings (McIvor, 1988). Once a grinding mill is in operation, few variables remain to be considered for process optimization. The ball charge is usually maintained to achieve a target power drawn by the grinding mill motor. The rotation speed is seldom considered (McIvor, 1983; Bazin and Lavoie, 2000) as a change of mill speed usually implies a costly pinion change. If the liner and lifter configuration is critical for SAG and AG mills (Latchireddi et al., 2005), few discussions are available for ball mills (Fuerstenau and Abouzeid, 1985; McIvor, 1983). The mill feed size distribution can also be adjusted but this implies changing the upstream processes, which transposes the optimization process to another level. Modification to grinding media shape is a possible avenue (Cooper et al., 1994), but it remains that slurry density and grinding media size are probably the most frequently considered variables for the optimization of a ball mill."

Jan 1, 2007