Search Documents

By William A. Stickney

The zirconium-hafnium separation plant at Albany, Oreg., was the result of a chain of events that started with studies by A. R. Kaufmann at the Massachusetts Institute of Technology. Variations in the listed neutron-absorption cross-section of zirconium caused him to suspect a misprint. As a result of these discrepancies and following his suggestions, Oak Ridge scientists made studies establishing a value of 0.4 barn or lower. This meant that the potential of zirconium for reactor application was greatly enhanced. Since hafnium is invariably associated with zirconium and has a high neutron cross-section, it was necessary that an efficient hafnium-separation method be developed before the superiority of zirconium as a structural material in nuclear reactors could be realized. The Albany plant was built and operated for the Atomic Energy Commission (AEC) under Letter Agreement AT-(11-1) -140, patterned after a plant operated by the Carbide and Carbon Chemicals Corp. at Oak Ridge, Tenn. Construction was begun in April 1951. Hafnium was to be extracted preferentially as hafnium thiocyanate from an aqueous mixture of zirconyl and hafnyl chlorides in hexone (methyl isobutyl ketone) by a liquid-liquid countercurrent system.

Jan 1, 1959

By E. D. Palmes

A new type of personal sampler for quantitative estimation of atmospheric concentrations of contaminant gases was first reported from this laboratory in 1972. The sampler requires no pumps or flow regulators and employs instead the motion of the gas molecules them-selves to furnish the power for sampling. Under this grant, work was completed on development of a kit for the field determination of both NO2 and NO. Detailed instructions for the preparation of the samplers and the use of the kit was supplied to the Technical Project Officer. Attempts were made to adapt the same type of sampler to the measurement of SO2 and CO. Both gas chromatographic and turbidimetric procedures for the final estimation of the S02 proved to be unsatisfactory. For CO no reagent was found which would react sufficiently rapidly with this gas to utilize the essential feature of the diffusion sampler, the maintenance of a diffusion gradient which is at least approximately numerically equal to the ambient concentration. A number of publications on use of the NO2 sampler, both at occupational and community air pollution levels, have resulted from this work.

Jan 1, 1979

By L. J. Vincze

The high cost of constructing mineral processing plants in remote locations warrants a close examination of the alternatives available for reducing the amount of on-site construction work. Among the alternatives are portable process plants, modular design and barge mounted plants. Each alternative has certain advantages as well as limitations depending upon specific conditions. On the basis of practical experience and engineering analysis, the paper examines the potential benefits to be realized by these techniques and summarizes the conditions required to obtain them. The potential savings indicated by such studies should encourage consideration of innovative design features for new plants located in remote areas.

Jan 1, 1980

By A. M. Ouchi

Existing empirical design tools have been developed from fair-to-good quality rock masses (RMR76 >50). This paper presents a focus of ground control research presently being conducted by the Rock Mechanics Group in the UBC Mining Department in incorporating weak rock masses (RMR76 <50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented with over 450 weak rock data points from mines such as the Stillwater mine (Montana), the Eskay Creek Mine (BC) and several mines in the Carlin Trend and other parts of Nevada. The original database is comprised of spans supported with ?traditional? mechanical bolting. In weak rock environments however, this type of support has been found for the most part, ineffective. This paper presents the span and weak rock RMR76 relationship for four different support categories. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

Jan 1, 2008

By R Kerrich

Early-Archaean (3.26 Ga) volcanogenic massive sulphide (VMS) deposits located within the low strain and sub-prehnite-pumpellyite metamorphic-grade Strelley greenstone belt, East Pilbara, Western Australia, contain exceptionally well preserved sulphide textures which are directly analogous to those of sulphide chimneys formed by black smokers at present day submarine hydrothermal vents. The VMS deposits are associated with seafloor alteration zones in and below silica-carbonate laminites, at the top of tholeiitic to calc-alkaline intermediate and felsic rocks. VMS mineralisation comprises stratabound Zn-rich sulphide lenses with significant Cu and barite, and variable Pb and Ag, above Cu-rich stringer zones, all of which are similar to Phanerozoic polymetallic or Kuroko VMS deposits. Sulphide-sulphate mineralisation implicates hydrothermal discharge into sulphate-bearing ocean waters, ruling out a globally anoxic Archaean hydrosphere. The volcanic rocks and co-magmatic sub-volcanic intrusion hosting the VMS deposits are characterised by the conjunction of LILE&gt;LREE&gt;HREE, and Phanerozoic La/Yb with negative normalised anomalies of Nb, P and Ti, consistent with derivation via subduction zone hydrous metasomatism fusing the mantle lithosphere.

Jan 1, 1995

Grade uncertainty can have a number of important implications for a mining operation. One of the most significant risks in not considering grade uncertainty in planning is the over or under allocation of processing or mining capacity when compared to realised grades. This could lead to wasted capital expenditure or missed opportunities to add value. This paper demonstrates a method that optimises production capacity and mining schedules in the presence of grade uncertainty. Applying this method to the case study of a nickel deposit recommended a reduction in processing capacity, an increase in mining capacity and more extensive utilisation of stockpiles than optimisations completed with traditional methods. As a result, average NPV improvements of between seven per cent and 27 per cent were gained.

Dec 6, 2010

By Richard R. Marston, Scott Herr, Steve Pries, Donald L. Jr Ewart

The purpose of this paper is to identify and examine alternative methods (other than shovel/truck stripping) of effecting the pre-stripping of consolidated overburden, in conjunction with dragline stripping operations, at surface coal mines. The analysis will be case study oriented with practical mining considerations and comparative economics being evaluated. Alternatives that will be examined include blast casting, dozer push, and multiple pass dragline sequences.

Jan 1, 1992

By Juan Lizana

El presente trabajo describe el proceso del sistema de gestión estratégica en la mina San Rafael, Puno. En este sentido, la empresa como parte introductoria de sus operaciones, ha propuesto la solución integral, donde la herramienta principal son los índices de gestión por unidades estratégicas de negocio y los índices de gestión por unidad operativa, los mismos que permitirán evaluar el desempeño de su organización frente a sus metas, objetivos y responsabilidades. En este sentido, el establecimiento de este sistema busca crear una cultura en la organización, a través del seguimiento de cada uno de los índices, permitiendo a la alta gerencia y a los demás niveles ejecutivos de la empresa hacer control de gestión, así como una reducción de los costos operativos en el Área de Mina y mejoras en los resultados de voladura.

Sep 12, 2005

By Lester J. Crow

This study advances the use of elemental sulfur in structural materials by demonstrating its value in bonding high-strength, well-graded basalt aggregates to form sulfur-basalt concretes. Sulfur is an excellent bonding agent, and the strength of a thermoplastic sulfur-aggregate mixture depends, to a large degree, on the strength and grain-size distribution of the aggregate used. A 3-cubic-foot, electrically powered mixer with heat applied to the barrel was used to mix the sulfur and aggregate. Sulfur content of several mixtures was varied to obtain the best workability with a minimum of sulfur in excess of that necessary to fill the voids. The average grain sizes and grain-size distributions were also varied to determine their effects on strength. Unconfined compression tests of forty-five 6-by l2-inch cylinders yielded average strendths of 3,348 psi to 10,398 psi. The highest strength single cylinder was 10,717 psi. The cylinders were tested from 24 hours to 6 days after pouring; after 24 hours the rise in strength was very slight. From the results obtained it appears that sulfur can be a useful construction material. An evaluation was made of a high-vacuum application for sulfur concrete. Sulfur has a high vapor pressure at elevated temperatures, 50° to 100° C; consequently, significant losses by sublimation can be expected. At lower temperatures the losses are not significant; however, this factor will limit its use at a higher temperature.

Jan 1, 1970

By Donald A. Bruce

"Abstract The Deep Mixing Methods (DMM), in their current forms, have been employed in the United States since 1986, although an earlier version had seen service from 1954. The earlier developments were strongly influenced by practices in the Nordic countries and Japan, while by the late 1980’s several DMM systems had been developed in the U.S. itself. Since then, DMM has continued its evolution, principally via the challenges of a series of large, landmark projects, but also via distinct, significant technological advances. This paper highlights the key points in the history of DMM in the U.S., and provides an overview of the different methods currently in use.In the BeginningIt is a common misconception that the history of applications of the Deep Mixing Methods (DMM) in the United States dates from 1986 when SMW Seiko Inc. — a subsidiary of Japan’s Seiko Kogyo Company — was established in the Bay Area. However, the author believes that Intrusion Prepakt Co.’s patented MIP (Mixed in Place) system had been used, albeit sporadically (about 30 projects are recorded), since 1954 (FHWA 2000, 2001). Ironically, by 1961 this single auger method had been extensively used under license in Japan for excavation support and groundwater control — by the Seiko Kogyo Company. By 1972, the original MIP technique had been succeeded by more advanced Japanese methods, involving multiple augers. Intrusion Prepakt have long since become defunct.The first systematic studies of contemporary Deep Mixing Methods in Japan began in 1967 when the Port and Harbor Research Institute of the Ministry of Transportation began laboratory testing using granular and powdered lime for treating soft marine soils. Fundamental studies continued through the early 1970’s, by which time the development of industrial scale equipment was well advanced, having its first application on a marine trial near Haneda Airport. Coincidentally, laboratory and field research also began in 1967 in Sweden (“Swedish Lime Column Method”) for treating soft clays using unslaked lime. Reportedly the progenitor was a Norwegian, Kjeld Paus, who had made observations on fluid lime columns in the U.S. It would seem that developments in Japan and the Nordic countries proceeded independently until 1975 when the technology leaders from each group (Broms and Boman; and Okumura and Terashi, respectively) presented their — very similar — findings at a conference in Bangalore, India. Limited technical exchanges ensued thereafter.Whereas the Nordic developments continued to focus on the use of dry reagents (cement and lime) and relatively light equipment compatible with operating on and in very soft clays and organics, the Japanese progressed into the use of fluid reagents (cement-based grouts) and heavier equipment for both marine and land-based projects. Thus, by 1986, there were a large number of proprietary (wet and dry) DMM systems in Japan, and a rapidly growing market already by then accounting for over 12,000,000 m3 of ground treatment."

Jan 1, 2014

By D. Strachan

Installation of support in known poor ground intersections during reaming operations requires rapid access to stabilize the shaft wall and thus to prevent the loss of the shaft through scaling. This is especially relevant to shafts of long dimension where the duration from time of exposure to time of support installation is lengthy This paper deals with the innovative methodology employed at Harmony?s No. 8 Shaft 17/24 level sub ventilation shaft to rapidly support a shale intersection between 23 and 24 Level by employing a single deck stage suspended from the reamer head by means of Skyjack winches.

Jan 1, 2009

By M. H. Rogers

Coal has been at the forefront of mankind?s drive to improve his quality of life and also for sustainable development, from the Industrial Revolution onwards. The international coal industry today is large, with some 3,7 billion tons being produced and consumed in 1997. South Africa is an important participant in the coal industry, selling some 220 million tons in 1997 of which 64 million tons were exported. It is the second-largest thermal coal exporting country in the world. Despite the size of the world coal industry, it is not immune to change. The address examines growth projections for the industry and the change drivers that will impact on it in the future. Environmental pressures, the most important of which being the climate change debate, the Kyoto Protocol arising from this debate and the development of clean coal technologies, to reduce the impact of coal production and usage on the environment are considered. Other major change drivers considered are competition from other sources of energy and that between coal producers, the deregulation of the electric power industry, corporate restructuring and for the South African producer, legislative reform. The declining (real term) coal price, the consequent squeeze on margins and the need for producers to actively contain costs is covered. Technology has, in the past, been the driver behind the growth and change of the South African coal industry and its future role in ensuring that coal is the fuel of choice for continued improvement in standards of living and economic development is addressed.

Jan 1, 1999

By M. Grodner

Underground excavations exhibit different hangingwall conditions in response to varying geotechnical and mining situations. These differences need to be quantified so as to accurately determine the effectiveness of the mining and/or support strategies. A useful tool for the quantification of these differences is hangingwall profiling. Two methods of hangingwall profile measurement are described?termed irregular and periodic methods. Several data analysis techniques are reviewed for these methods and the suitable ones are discussed in detail. For irregular data the suitable techniques are the determination of the length, the average of the profile and the average absolute deviation from the mean of the profile. All of these techniques as well as determination of the moving average of the height and examination of the spectral image of the profile can be successfully applied to regular data. The effect of preconditioning on the hangingwall is discussed as an example and it is quantitatively shown that it results in improvements of conditions. The techniques described allow the engineer to quantitatively identify the appropriate support type or mining strategy and thus represent a valuable decision-making tool. It is suggested that these techniques should be employed on a routine basis by the rock engineers on the mines as part of their geotechnical classification, as well as support manufacturers to quantify the effectiveness of various support types.

Jan 1, 2000

By Gregg Hodges, Fred Schoenbrunn, Steve Slottee, Chad McCleary

"In December, 1999 Stillwater Mining Company (SMC) commissioned a new paste /cement backfill plant to supplement the existing sand backfill system for the cut and fill mining operation at it’s Nye, Montana mine. The new plant uses the Baker Process Deep Cone TM Paste Thickener to thicken the total concentrator tailings from 30% solids slurry to a 71% solids paste. This paper describes both general paste formation concepts and the evolution of the SMC paste plant operation from original design criteria, through problem solving and plant modifications, to the operation of the existing plant.Although the original process design was not effective for consistently producing and delivering acceptable paste to the stopes for backfill, SMC was able to make the mechanical and process modifications which allow the plant to now produce and deliver an acceptable product to the stopes. Ongoing test work is targeted at increasing the pumping range of the system, increasing the paste solids concentration from the Deep Cone Paste Thickener and reducing the operating and maintenance costs of the system.INTRODUCTIONThe authors would like to thank both Stillwater Mining Company (SMC) and Baker Process for their assistance in the preparation of this paper. Stillwater Mining Company chose not to participate directly in this paper due to time constraints, but was very helpful in answering questions concerning their approach to problem solving and specific details with regard to engineering criteria.This paper will begin with a general review of the technical and mechanical concepts in paste formation and then focus on the overall design, start-up and problem solving process for the paste backfill operation at SMC’s mine and concentrator near Nye, Montana."

Jan 1, 2001

By H. Yen, D. E. Walsh, H. K. Lin

"Comminution circuits are widely used in nonferrous and precious metals milling. Steel crushers, grinding mills and grinding media are typically used in comminution circuits. Comminution circuit wear products, in the form of metallic iron (steel) fines, are unavoidably produced and report to undersize products in the classification circuit, i.e., flotation or leach feed, while tramp grinding steel (TGS) reports to classification oversize products and returns to the grinding mill, building up in the circulating load. In laboratory studies, TGS reduced grinding efficiency significantly, the impact being dependent upon the size of the TGS present in the mill. Because iron fines adsorb flotation reagents effectively, iron fines increase reagent consumption and reduce flotation recovery. Iron fines are also capable of reducing gold recovery in cyanidation circuits via a cementation reaction. When using filtered gold solution from the cyanidation circuit of an Alaskan gold mine, the gold concentration in solution was reduced by 0.2 to 2.6% over various reaction periods when iron fines were present in the solution.IntroductionComminution circuits are widely used in copper, lead, zinc, nickel, cobalt, molybdenum and precious metal mills. Flotation and leaching processes are usually preceded by comminution (crushing and grinding) circuits in order to liberate valuable minerals for effective separation, concentration or dissolution by the subsequent flotation or leaching processes.Steel crushers, grinding mills and grinding media are typically used in comminution circuits. Comminution circuit wear products, in the form of metallic iron (steel) powder, are unavoidably produced and report to undersize products in the classification circuit (flotation or leach feed), while tramp grinding steel (TGS) reports to oversize productions during classification and returns to the grinding mill, building up in the circulating load. Variables affecting the amount of metallic iron powder and TGS produced in a comminution circuit include ore hardness, grinding mill operating conditions, comminution circuit design and the metallurgy of the steel used for manufacturing crusher liners, mill liners and grinding media. As one example, a comminution circuit product of 80% passing 200 mesh at the Pogo Mine, AK is estimated to contain approximately 2 kg/t of metallic iron. A finer grind will generally produce a comminution circuit product with higher metallic iron fines content."

Jan 1, 2015

By A. T. Robles, L. Buckingham

"When certain gold ores containing pyrite, graphite, humates and fumates or other organic compounds which are possibly adsorbed on clay minerals are treated with aqueous solution of alkali metal cyanide, the aurocyanide complex which forms is adsorbed by these ""pregrobbing"" species in the ore. Dissolution of gold proceeds until chemical equilibrium is attained between the cyanide complex adsorbed by the ore and in solution.Sodium lauryl sulfate (SLS) may be used to decrease the adsorptive activity of the prerobbing species in the ore. It has successfully improved recovery at Holt-McDermott Mine and is highly biodegradable.INTRODUCTION Precious metal-bearing ores containing preg-robbing species are poorly amenable to standard cyanidation techniques. The ""preg-robbing"" impurities with which they are associated tend to adsorb the gold cyanide complexes and carry them through the circuit to the tailings. Also, gold may be associated with these impurities in the ore and not be leached by the cyanide complexing agents used in conventional cyanidation techniques.Methods for dealing with the problem of preg-robbinq impurities in gold ores are:Carbon-in-Leach (CIL), in which granular activated carbon is added to compete with preg-robbing species for the gold cyanide complexes. This process can improve gold recovery in mildly preg-robbing ores especially when fine carbons with very high activities are used. However, with severely graphitic ore, the carbon associated with the rock may outperform the granular activated charcoal.Chemical Oxidation, in which the ore is subjected to preliminary chemical oxidation techniques to oxidize carbonaceous materials using such diverse reagents including ozone, sodium hypochlorite, calcium hypochlorite, chlorine gas, permanganates, perchlorates, chlorates and oxygen prior to subjecting the oxidized ore to standard cyanidation treatment to extract gold. This is generally a costly method and will not prove economical on a low-grade ore."

Jan 1, 1992

By H. D. Kline

This publication describes methods and techniques of mining and crushing limestone at 3 of 11 small quarries operated by Anderson-Oxandale Rock Co. in northeast Kansas in 1959. It is one of a series of reports by the Bureau of Mines on methods and costs of mining in various mining districts in the United States. The three quarries selected for study -Bosse quarry, Pottawatomie County; Hansen quarry, Morris County; and Huston quarry, Dickinson County (fig. 1) -were in many respects similar to many others that had been developed solely to fill local and usually transitory demands for crushed limestone for use as concrete aggregate, roadstone, and soil conditioning. Factors governing the choice of quarry sites were quality of limestone, shallow overburden, and proximity to points of consumption of the crushed stone.

Jan 1, 1962

The unpaved road network on a surface mine is extensive, comprising numerous roads of varying construction and material qualities with highly variable traffic volumes. Existing haul road maintenance management systems (MMS) work well for predictable traffic volumes, but for complex mine road networks, the MMS becomes onerous. This results in sub-optimal road maintenance strategies with the attendant increase in total road-user costs and reduction in service. A real-time maintenance management system was thus sought to overcome the deficiencies of existing MMS for mine roads. Since most large mines operate trucks with on-board diagnostic data collation, linked through a centralized communication and GPS backbone, it was proposed that road condition could be monitored on a real-time basis through on-board vibration signature analysis. The aim of this paper is to present the development of a real-time mine haul road maintenance management system. Following are view of mine road maintenance practices, the real-time system architecture is introduced and the results of a field trial of on-board vibration signature assessment is presented. The trial results are discussed in the light of road defect signature recognition, analysis, signature repeatability and system limitations. This approach has applicability to other situations such as a network of district roads, subject to an analysis of the economic feasibility. The paper concludes that modern technology has the potential to apply maintenance as and where needed with possible reductions in authority cost and an improvement in service provided for the road user.

Jan 1, 2003

By Mario E. Rossi

Las simulaciones condicionales geoestadísticas se utilizaron como herramientas de control de leyes en operaciones diarias que evalúan la incertidumbre y el riesgo de las reservas mineras en estudios de factibilidad, así como el potencial de mineralización en ciertos ambientes geológicos. Otras aplicaciones incluyen evaluación de recursos y reservas recuperables (dilución), clasificación de recursos y reservas, y optimización de espaciamiento de sondajes. En ese sentido, el presente trabajo señala los aspectos de los esquemas de clasificación de recursos y reservas utilizados en la industria, el cual está basado en el modelo de incertidumbre que las simulaciones condicionales proveen. Asimismo, se analiza el riesgo que este modelo de incertidumbre implica para sub-regiones (unidades) de extracción del yacimiento, como las definidas por fases de extracción mineras o períodos de tiempo.

Jul 17, 2000

By H. G. Hammon

Uranium miners have been shown to develop lung cancer in direct proportion to the time of exposure in the mine and the concentration of radioactivity (cumulative working level).1 Radon gas is continually evolved from the uranium ore, but because of its shoe half-life, 3.82 days, it is soon decomposed into particulate daughter products, which along with the dust in the mine, become deposited in the miners&apos; lungs. At present, massive ventilation is the only effective method of reducing the radioactivity concentration in the mines. However, the Bureau of Mines is evaluating the possibility of using coatings on the mine wall that will have sufficiently low permeability to radon that the gas will decompose into the particulate daughter products before it can permeate the coating. Permanently trapped in the coating, the daughter products would be prevented from dispersing in the mine atmosphere. Lawrence Livermore Laboratory was asked to aid in this investigation. The direct determination of radon permeability is more difficult than that of the other noble gases because of the short half-life of the gas and radioactive contamination of the apparatus. We felt that it should be possible to estimate radon permeation coefficients from other noble gas permeation coefficients. It was noted that the log of the diffusion constants for helium, neon, argon, and krypton, as reported by Meares2,3 plotted to a straight line-against the square of-the gas molecularddia meter. The log of the permeation coefficients also plotted to a straight line against the square of the gas molecular diameter. Thus, by determining the permeation coefficients of such gases as argon and krypton through various films and coatings, it appeared likely that radon permeation coefficients could be estimated. In addition we felt it should be possible to find some relationship between polymer structure and he noble gas permeation coefficient that would aid in the selection of coatings materials as radon barriers.

Jan 1, 1975