Search Documents

By M. E. Smith

Waste rock dumps, tailings impoundments and spent leach heaps are common features at mine sites. Many of these waste disposal facilities contain sulfide-rich minerals, which generate acid mine drainage (AMD) when they oxidize. Control of AMD can be achieved by removing one or more of the three essential components in the acid-generating process (sulfides, air, or water). One AMD prevention measure is to cap the waste with an engineered cover system to minimize the infiltration of water and diffusion of air into the system. Possible cover designs include: ? Earthen ?store-and-release? covers (also known as evapotranspiration (ET) or water balance covers), including capillary barriers. These covers require climate conditions where there is both modest to little rainfall and significantly greater evapotranspiration than precipitation, both annually and seasonally. ? Low-permeability compacted clay liners (CCLs) employing fine-grained soils typically compacted at wet of optimum water content. ? Geosynthetic composite covers, comprised of a geomembrane liner placed over and in direct contact with either a CCL or a geosynthetic clay liner (GCL). These systems have been commonly used for base liners for leach pads as well as covers and base liners at municipal solid waste (MSW) landfills in the US for more than 20 years. Comparisons of these different cover systems, both in terms of performance and cost, are presented later in this paper. First, however, a review of the typical mine closure approaches, and the possible rationale behind them, is warranted.

Feb 27, 2013

The discussion which followed the publication of my paper by the formert has, I think, enhanced its value. It may therefore be of interest to members of our Australasian Institute, who are not members of the Institution of Mining and Metallurgy, if I give a synopsis of the discussion.My attention was drawn to the fact that my paper did not make clear the extent of the improvement in furnace operations, which followed the use of coke of high quality; this comment applied more particularly to the lead content of slag. My failure to supply comparative figures in regard to the lead content of slag was governed by a condition which, I think, is of interest to metallurgists. As a result of industrial...

Jan 1, 1932

By Swaminathan Srinivasan, Jess A. Schroeder

"Landslide activity along U.S. 50 in Cincinnati, Ohio (USA) has caused roadway damage for decades. After a necessary closure of three lanes due to slope movements, emergency stabilization measures were undertaken to protect the roadway by providing a short-term solution necessitated by The Ohio Department of Transportation budget constraints. The landslide shear plane occurred on a sloping bedrock surface as much as 50 feet below grade. Drilled shafts were installed 40 feet downslope of the roadway shoulder and were heavily reinforced across the shear plane but steel reinforcing did not extend the full length of the shafts and was stopped well short of the ground surface. Instrumentation data has been collected for 11 years after construction has shown these “Stub Piers” have provided much more than a short-term solution and have provided an attractive alternate to conventional deep shafts or tieback drilled shaft options.INTRODUCTIONLandslide activity has occurred along U.S. Route 50 in western Cincinnati, Ohio for many decades. The site is located between North Bend and Addyston, Ohio on the right descending (cutting) bank of the Ohio River. Road distress caused by slope movements required periodic repairs over recent decades. Railroad tracks downslope of the roadway also showed signs of horizontal displacement and periodic repair. Visual evidence in 2005 suggested the shear plane extended below the US 50 roadway and extended out into the Ohio River.A weed and brush-covered slope extended down slope from the roadway at about 3H:1V for a vertical distance of about 20 feet. Above US 50, the hillside continued to rise more than 100 feet. There is a railroad right-of-way at the toe of the slope with the Ohio River bank just downslope of the railroad.In 2005, Terracon Consultants was retained by the Ohio Department of Transportation (ODOT) to perform a geotechnical study that included 17 test borings and inclinometer monitoring at 4 locations. Roadway damage was occurring (see Figure 1). After only a few weeks of monitoring, the inclinometer casings sheared off about 50 feet below grade, near the soil / bedrock interface (see Figure 2). Soon after, the roadway distress worsened, causing ODOT to close 3 of the 4 lanes to traffic and reroute traffic onto the remaining single lane and shoulder. Terracon was asked to develop a stabilization design under emergency repair conditions. However, both limited budget and time-related constraints necessitated a direction by ODOT that the solution be at least “pseudo” short-term (3 to 5 years)."

Jan 1, 2017

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2005 draws upon available information from literature, industry and U.S. Geological Survey (USGS) specialists. It provides data on exploration budgets by global region and mineral commodity and identifies significant mineral discoveries and exploration target areas. It also discusses government programs affecting the mineral exploration industry and presents analysis of the mineral industry based on these data. Two types of information are reported and analyzed in this annual review of international exploration for the year 2005. They include budgetary statistics provided by Metals Economics Group (MEG) and information on regional and site-specific exploration activities in 2005 compiled by the USGS.

Jan 1, 2006

By D. A. Wilson

A cyclic leaching process was developed for selectively leaching and recovering cadmium from nickel-cadmium scrap battery waste. The six major steps in the process are the following: (1) washing the plates to remove KOH electrolyte, (2) roasting at 550° to 600° C to oxidize metallic cadmium and decompose cadmium and nickel salts, (3) leaching with an ammonium nitrate solution, (4) precipitation of the leached cadmium from solution as cadmium carbonate using CO2 gas, (5) removal of CO2 from the lixiviator by adjusting to pH 4.5, heating, and evacuating the system, and (6) removal of small amounts of leached nickel from the lixiviator using a solvent extraction technique. The regenerated lixiviator is then recycled to leach additional plates. Cadmium extraction was 94 percent and the cadmium carbonate product contained 0.14 percent nickel and 0.12 percent cobalt impurity. The leached plates were smelted to a high nickel-low iron alloy with no detectable amounts of cadmium.

Jan 1, 1971

By D. C. Sharpstone

THE Polaris-Taku mine is a new gold property, situated in the far north-west corner of British Columbia. Production was started in November, 1937, at the rate of 150 tons a day, and recently has been increased to 200 tons. The property, which promises to become one of British Columbia's important gold mines, was developed and brought into production in twenty-nine months after work was started on it as a virtual prospect in June, 1935, by Edward C. Congdon and associates. Inaccessibility, extraordinarily complicated geological problems, and difficult metallurgy retarded development of the property before acquisition by the present interests, an::l, in fact, discouraged two companies that had spent substantial sums upon it from continuing development. This paper is concerned with reviewing the development of the property and describing the principal features of the geology, the mining and metallurgical practices, and the equipment employed. Acknowledgments The writer is indebted to Mr. Edward C. Congdon, President of the Polaris-Taku Mining Company, and to various members of the mine staff for their assistance in assembling the data for this paper. Special thanks are due to Mr. George G. Griswold, Jr., of Butte, Montana, who generously and painstakingly prepared the section dealing with milling and power. Microscopic studies of ores were made by Professors Frank Grout an::l G. M. Schwartz, of the University of Minnesota, and by Mr. Griswold.

Jan 1, 1938

By Georgene Renner, William R. Yernberg, Steve Kral

ABB offers complete electrical revamps of mining shovels with ac or dc drives, drive control, frequency converters with insular gate bi-polar transistor technology, intelligent control packages and visualization. Many of the world’s shovel excavators and draglines (walking excavators) were built in the1980s. After 15 to 20 years of round-the clock operation in openpit mines, these machines start to feel their age. Electrical parts are particularly vulnerable. Their performance deteriorates and availability and productivity fall. Even with regular ser-vice and maintenance, a machine of this age will accumulate 400 hours of unscheduled downtime a year. The need for a replacement becomes pressing, but the expense is often prohibitive.

Jan 1, 2005

By Eric Nordhausen

This report and associated deliverables is the culmination of a comprehensive literature survey, data collection and identification of over 500 metal/nonmetal active mines/mills/smelters (over 50,000 tons per year, TPY, production) in the contiguous 48 states. The main purpose was to compile an inventory of the mine/ mill/smelter waste tonnages, thus forming a data base for future research and development in improving waste management and waste disposal techniques in the metal/nonmetal mining industry. The study specifically excluded sand and gravel, sulfur, granite and any commodity that leaves basically no waste when mined and/or milled. The coal waste inventory is the subject of another report. The study provided for locating, mapping. encodating and digitizing all the mine/mill/smelter information made available throughout the nation as well as the climatological, land use, topographical, ecological and vegetative data. Mine/mill/smelter information also included (where possible) acreage and/or volume, mining methods, primary ore and gangue minerals, waste composition and haulage methods and distance hauled. Finally, a discussion is provided concerning present and potential uses of various types of tailings, as well 8S recommending possible R&D in addressing problem areas in waste disposal techniques and management.

Jan 1, 1981

By Robert J. Dompe

The objective of this program was to develop a cost effective microprocessor-based electronic image sensor system for monitoring pit slope displacement to detect and/ or predict impending slope failure in surface mines. A background study and data analysis yielded a performance specification for candidate Video Slope Monitoring Systems. A design concept was developed based on using a pair of solid state video cameras located on precision pointing assemblies. The digital images from the cameras are compared and, using electronic triangulation, slope topology is calculated. The current and past locations of operator selected features are compared to determine pit slope displacement. A proof-of-concept test was performed using a laboratory model of a pit slope. Based on the successful results of that testing it is recommended that an in-mine evaluation be performed using a full-scale prototype Video Slope Monitoring System.

Jan 1, 1982

By Ronald T. Mayerle

A mineral survey of portions of two contiguous WSAs (Wilderness Study Areas) along the South Fork Owyhee River in southwestern Idaho and north-central Nevada was done by the U.S. Bureau of dines in 1984. The portions of the WSAs, known as study areas, have a combined area of 47,610 acres. The Idaho study area consists of 42,430 acres of the 42,510-acre South Fork Owyhee River WSA (ID-16-53). The Nevada study area consists of 5,180 acres of the 7,840-acre South Fork Owyhee River WSA (NV-010-103A). The Idaho study area is within the Boise District of the Bureau of Land Management, and the Nevada study area is within the Elko District. In the Nevada study area, no claims or hard rock mineral occurrences are known.

Jan 1, 1986

By J. A. Kosek

Work has been conducted under Bureau of Mines Contract Number HO 357078 to develop instruments for detecting CO, NO and NO2 in a mine atmosphere, using fuel cell technology. The approach has been to optimize the fuel cell sensor configuration for the specific detection of CO, NO and NO2 in the presence of other mine gases utilizing recent advances in catalyst, electrode and solid polymer electrolyte membrane technology. Para-metric testing has been conducted on three electrode sensor cells to define performance and life characteristics as a function of temperature, feed flow and applied sensor voltage. Extended life testing has been performed on sensor cell configurations exhibiting favorable characteristics. Reliable, efficient gas sampling and electronic control circuitry has been fabricated for use with the sensor cells, and integrated into devices to meet the performance and design specifications for portable, battery-powered, hand held direct indicating gas detectors for use underground. Twenty of the production-type, direct indicating CO detectors have been tested and delivered to the Bureau of Mines under the present contract. Three prototype diffusion head CO monitors have also been delivered for evaluation under the pre-sent contract. The gas sampling pump and related parts have been replaced by a diffusion tube assembly in which CO reaches the sensing electrode surface by diffusion alone. In addition, delivery will be made of ten direct-indicating nitric oxide detectors and ten direct-indicating nitrogen dioxide detectors. These instruments are very similar in design to the direct indicating CO detector.

Jan 1, 1979

By John R. Benham

The Windigo Theilson RARE II area has a low mineral potential. There are no mines or claims in the area. The only observed results of mining activities were five prospect pits near Tolo Mountain. Samples from these pits contained no significant assays. The study area contains more than 190 million cu yds (145 million m3) of cinders in 17 cones. Development of these cinders is unlikely because their locations are remote, and other sources supply area needs. The Geological Survey has classified the area as prospectively valuable for geothermal resources. However, there has been no geothermal exploration activity.

Jan 1, 1982

By Elmer Stewart, Richard May

"The Central Mukur deposit was discovered by the Semipalatinsk Geological Exploration Expedition (GEE) during detailed searches from 1977 to 1980. Andas Altyn Ltd., a Kazakhstanian gold mining company acquired the property and commenced mining in 1995. In 1998, Andas-Altyn Ltd. became a wholly owned subsidiary of Eurasia Gold Corporation.The Central Mukur gold project covers a linear series of parallel, discontinuous zones of near surface oxide gold mineralization that covers a distance of 7 kilometers and extends past the property boundaries. The oxide gold mineralization is a result of the regional oxidization of a primary sulfide gold mineralization emplaced in a series of shallow dipping thrust faults. Resources as calculated by the GEE are 3.45 mt at an average grade of 1.84 gmt Au in the C1 +C2 category and 7.52 mt at an average grade of 1.80 gmt Au in the P1 category. The Central Mukur Gold Heap Leach Mine consists of an open pit, heap leach pads, and an ion exchange resin gold recovery plant. Limited gold production (<2,500 ounces/year) has been achieved over the past three years leaching run of mine oxide gold mineralization. Gold recovery utiling cyanide to dissolve the Au and ionic resin technology to recover the Au for the leachate is approximately 60%. Loaded resin is shipped to a treatment plant at Almaty where the gold is stripped from the resin, refined and sold.This paper will describe the geology, mining, and processing of the Central Mukur ore. In addition, it will describe what it is like doing business in Kazakhstan and the transition from a Soviet style operation to a more western style operation.INTRODUCTIONThe Central Mukur Mine is owned and operated by Andas-Altyn Ltd. a Kazakhstanian gold mining company located in northeast Kazakhstan. Andas-Altyn is a wholly owned subsidiary of Eurasia Gold Corp., a Canadian public company listed on the Alberta Stock Exchange. The Central Mukur mine consists of a small open pit, and a heap leach operation that utilizes ion exchange resin to recover gold from pregnant solutions. In addition to the Central Mukur mine, Eurasia also owns the Myaly heap leach gold project which is also operated by Andas- Altyn Ltd."

Jan 1, 1999

By G B. Arehart

The Midas epithermal system is one of the larger low-sulfidation epithermal vein systems discovered in the western US in recent years, containing in excess of 3 Moz of gold (premining). The deposit is spatially and temporally related to bimodal volcanism in the Northern Nevada Rift; dates on igneous rocks (16 - 14.7 Ma) bracket the age of high grade veins (15.3 Ma). Hydrothermal alteration at Midas is typical of epithermal systems, comprising proximal potassic through distal propylitic assemblages; in contrast to many epithermal systems, Midas has minimal development of wallrock illite/sericite. Mineral assemblages are clearly zoned on the vein structures that acted as focal planes for fluid upflow. Geochemical zoning patterns also show this zoning. Metals were deposited in open-space veins as the result of boiling of hydrothermal fluids; multiple episodes of crustiform mineral deposition are documented in the vein textures. The major vein minerals include quartz, adularia, calcite, selenides and sulfides, with electrum as the primary ore mineral. REE patterns for vein material are similar to patterns for coeval rhyolites, but distinctly different from patterns of the host rocks. Stable isotope data are consistent with meteoric water as the dominant ore fluid. Combined REE and stable isotope data suggest that fluid from which the main ore-bearing stage of the veins was deposited was slightly lower pH than other stages.

Jan 1, 2005

By Robinson KJ

There has been much debate in recent years regarding the number of Geology (Earth Science) graduates produced in Australia. The key variable has commonly been assumed to be the placement of graduates in the mineral and petroleum industries. Although not wishing to deny the importance of this element, we contend that Geoscience studies should be given to a wider variety of graduates. The essence is to make students and future citizens more environmentally aware. INTRODUCTION Geoscience is fundamental to exploration and to the well-being of the minerals industry and hence the Australian economy. The value of mineral primary products exports for the past three years has been: 1895 $15.3 billion 1986 $14.8 billion 1987 $16.3 billion (Data source: B.M.R) The mining industry supplies about 40% of Australia&apos;s export earnings. However the overall value of Geoscience to the Australian economy is much greater. At the opening of the ANZAAS conference in Townsville during May 1987, Sir Bruce Watson , Chairman of the Mt. Isa Mines Ltd., made a plea for a national re-examination of the way science is taught in secondary schools. In particular he emphasized the point that the community should be more aware of the importance of Geoscience and the value of the mining industry to Australia.

Jan 1, 1989

THE Synthetic Liquid Fuels Act (30 U.S.C., 321-325, and amendments) become law April 5, 1644, and a period of intensive research and development in this field was begun by the Bureau of Mines. As part of this program bulletins were published on a pressure hydrogenation,3 the Fischer-Tropsch synthesis,4 and oil shale.5 The Bureau also has published a short bibliography on coal gasification,6 mostly of a theoretical nature. Because coal gasification is prerequisite to Hither the Fischer-Tropsch or coal-hydrogenation processes, publishing this sizable, collection of technical information in this form will be valuable. The material is presented in three parts, as follows: I. United States Patents. II. United Kingdom, Australian, Canadian, and South African Patents. III. Belgium, French, German, Italian, and Swedish Patents. The domestic patents for this bulletin were collected between 1963 and 1955. Some of the Foreign Patents were collected at the same time and a few of them later in 1961. Part I was published in 1960; Part II was published in 1962.

Jan 1, 1964

By D. C. Dahlin, W. K. O’Connor, G. E. Rush, C. A. Summers, S. J. Gerdemann

The Albany Research Center (ARC) conducted studies of mechanical activation by conventional and ultra-fine grinding techniques to enhance olivine reactivity in mineral carbonation reactions. Activated olivine is one of several solid feed materials used at ARC in reactions with carbon dioxide to form carbonate minerals. This paper compares grinding techniques via energy demand data and product characteristics, including particle size distributions, surface areas, full width at half maximum (FWHM) XRD analyses, and particle morphology by SEM analyses. Reactivity was gauged by percent conversion to carbonate in subsequent carbonation tests.

Jan 1, 2004

Study on Separation Technology for Copper-Molybdenum Collective Concentrate

Sep 13, 2010

By Martin Kesting

The world wide growth dynamics and the continuously growing demand for energy, results in increasing energy prices. Looking from this point, the efficient exploitation of fossil fuel deposits has become a more important factor to the production of energy raw materials than ever before. This shall be reached by an increase of the automation degree of the bucket wheel excavator in the open pit mining as well as a quality increase of the entire mining process chain. A further optimization of this operation can only be achieved by gathering additional information about the input parameters. The earlier and more exact the description of the input parameter, the greater the effectiveness of the entire process chain. To address this major issue, the RWE Power AG assigned the Institute for Transportation and Automation Technology with the research project "SIMT, Sensory Identification of Material Type and Detection of the Interfaces" [Kes07]. Presently, the control of the bucket wheel excavator is carried out manually by the operator, as well as the visual identification of the different geological layers and the energy raw materials. In this paper, a sensor-system is introduced, which was developed in order to transfer the manual material identification and detection of interfaces into an automatic online procedure. A special challenge and the main focus of this contribution is the integration of this sensor system into a bucket of the bucket wheel excavator. For measuring procedures where direct contact with the in situ material is necessary, the sensor has to be integrated into the bucket. Since direct contact with the material is not necessary, it can be integrated next to the bucket wheel. The results of a preliminary study show that although there is a broad spectrum of sensor technologies for material and interface identification, only a few are suitable for an application in on-line measuring at the bucket wheel excavator. Taking into consideration the demands on the sensor technology, the studies carried out and comparable applications of individual sensor technologies which have already taken place in practice, the integration of the following measuring systems have been realized: ground penetrating radar / reflection measurements, geo electric, resistance geo electric technology. The solution developed in the research project offers for the first time the direct integration of sensor systems into the bucket of a bucket wheel excavator. It will now be possible to test other measurement methods and sensors, not only for the ones already mentioned. As an example the integration of a triaxial accelerometer to measure the solid borne sound and vibrations concerning the cutting of different materials will be shown.

Oct 1, 2009

By C. Siyasiya

One of the problems that is occasionally encountered during the continuous casting of DIN 1.4003 stainless steel (hereafter referred to as 1.4003) is the side bulging effect, a problem that is generally prevalent in ferritic stainless steels. This occurs because the unconstrained narrow sides of the solidification shell are not able to withstand the ferrostatic pressure once the strand has emerged from the mould. Coupled with side bulging, there is strand width variation at high temperatures, i.e. when the steel is in the ferrite-austenite dual phase region. Both of these dimensional changes to the slab profile create some processing problems in subsequent hot rolling operations when unacceptable width variations are encountered. The strength of the solidification shell and its ability to withstand the ferrostatic pressure during continuous casting is dependent on its thickness and phase composition when exiting from the mould up to a few metres downstream. From the study of the high temperature metallurgical behaviour of this steel, it was observed that a thicker solidification shell when exiting from the mould and a higher austenite volume fraction in the steel would be favourable for the reduction of the side bulging effect during continuous casting. It was also found that as long as the d-ferrite to austenite phase ratio keeps fluctuating due to variations in chemical composition and process control in the dual phase region from cast to cast, the strand width variation problem would probably persist. The remedy to this effect lies in more strict chemical composition and process control during continuous casting of this steel. The hot ductility experiments revealed that 1.4003 exhibits good hot ductility in the strand straightening temperature range with a minimum of 75 per cent reduction in area and this was attributed to the high volume fraction of ferrite (0.2 to 0.4) in the steel. This would provide a remedy to side bulging by increasing the secondary cooling rate of the strand in order to form a thicker solidification shell without necessarily risking transverse cracking and other surface defects during unbending. Keywords: side wall bulging, resistance bending moment, applied bending moment, ferrostatic pressure.

Jan 1, 2005