Search Documents

By L. Li

The performance of microemulsified diesel and conventional diesel collectors in coal flotation was compared by flotation indicators, including combustible recovery, ash content of the clean coal, and the flotation index. An efficient separation with lower dosage was obtained using the microemulsified diesel collector. Under optimum separation conditions, the microemulsion consumption was 100 g/t less compared with diesel. The saving in diesel consumption using the microemulsion reached about 70%, disregarding the consumption of the surfactant and cosurfactant. Frothing tests showed that the frother dosage was decreased by using the microemulsion collector, because of the surfactant and cosurfactant added during preparation. The microemulsified diesel collector is superior to the conventional diesel collector in terms of diesel consumption and separation efficiency, but the selectivity requires further improvement. Keywords froth flotation, microemulsified collector, coal.

Nov 1, 2013

By I. Ewart, E. Roux

Skorpion Zinc operates a solvent extraction/electrowinning zinc plant producing over 150 000 t/a of special high grade (SHG) zinc (>99.995% Zn). In the current flow sheet copper and cadmium are cemented from the neutral leach solution using zinc powder, to prevent galvanic corrosion of plant equipment and build-up of copper in plant solutions. This process is effective but unfortunately consumes expensive zinc dust and produces a low value copper product. The EMEW® (Electrometals electrowinning) technology of Electrometals Technologies Ltd. uses a rapid flow of electrolyte through a cylindrical cell to deposit copper or other metals from dilute solution (less than 1 g/L) [1]. The copper can be deposited as powder or may be harvested as a tubular cathode product. The advantage of the use of EMEW® technology at Skorpion Zinc will be to eliminate the use of expensive zinc dust and to produce a high value copper product for sale. Following extensive bench test work, a piloting campaign was carried out at Skorpion Zinc. The tests demonstrated the ability of the EMEW® cell to effectively remove copper from solution through direct electrowinning at lower operating cost than cementation. Keywords: Skorpion Zinc, copper, cementation, direct electrowinning, EMEW®

Jan 1, 2007

Understanding multiphase particulate systems is essential for the further advancement of mineral processing technology. Characterisation, analysis, and simulation of these complex systems provide a fundamental basis for the development of improved mineral processing technology. One of the more recent tools that can be used to help provide a foundation for improved mineral processing technology is high resolution cone beam X-ray micro computed tomography (CT). During the past ten years point-projection X-ray micro CT systems have been used for 3D visualisation and quantitative analysis of multiphase particulate systems. Analysis of packed particle beds containing as many as 30 000 particles can be accomplished in less than three hours with special software to establish the 3D characteristics of each particle in the population and the spatial organisation of the packed particle bed. Now, due to advances in X-ray optics, the resolution afforded with point-projection micro CT systems has been improved by at least an order of magnitude using a lens-based X-ray micro CT system. The development of software tools for the 3D characterisation, analysis, and simulation of packed particle beds using high resolution X-ray micro tomography (HRXMT) is discussed including examples of application in the areas of comminution (particle damage and preferential grain boundary fracture), exposure/liberation analysis (liberation-limited separation efficiency, including coal washability), and filtration/heap leaching (pore network structure of packed particle beds and simulated flow using the LB method of computational fluid dynamics).

Sep 13, 2010

By M. Zanotto

[ ] A period of heavy rains caused the river Adda to flood parts of the Valtellina, one of the Alpine valleys of Northern Italy. The exceptionally high waters put under considerable strain the whole system of embankments and levees controlling the river and protecting the adjacent towns and lands. In some places the water breached and washed away the embankments, submerging large tracts of cultivated land, buildings, roads and railway tracks. The town of Talamona, in the lower Valtellina, was hit particularly hard: in its proximity the river overrun and then washed away 300 m (1,000 ft) of embankment (see vicinity map, fig. 2), depositing large amounts of riverbed debris onto over 400 hectares (1,000 acres) of fertile land.

Jan 1, 1992

The contract for the Water Jet Chock Mounted Miner Feasibility Study was awarded to FMC Corporation's Advanced Products Division on 18 November, 1974. The program was divided into four phases as follows: ? Phase I - Planning ? Phase II - Conceptual Design ? Phase III - Budgetary Cost Estimate and Economic Feasibility Study ? Phase IV - Final Report During Phase I, which lasted 1 month, most of the necessary information and data for the conduct of Phase II was obtained. To accomplish this, arrangements were made for personal visits to the University of Missouri at Rolla, Illinois Institute of Technology Research Institute, USBM TCMRC, Alpine Equipment Co., Mining Progress, Inc. and Eastern Associated Coal Corporation's Harris No. 1 Mine. Also, a list of manufacturers of high pressure equipment was compiled to be contacted during Phase II. Finally, the objectives to be accomplished during Phase II were outlined. The Phase I Report was submitted on 23 December, 1974. At the beginning of Phase II, personal visits were made to the research centers and firms mentioned above. Later an additional visit was made to the Harris Mine, and to the Pittsburgh Mining Research Center at Brucetun to observe a test of a water jet mounted on an Alpine Mining Machine. Equipment manufacturers of high pressure components such as hoses, tubing, valves, pumps, and intensifiers were contacted to obtain item performance data, availability, and cost.

Jan 1, 1975

WHEN making comparisons of the efficiencies of different grinding and crushing machines it is desirable to be able to estimate the work actually done in crushing the ore from a given size of feed to a given size of product, the screen analysis of both feed and product being determined. Messrs. Klug and Taylor, in a paper on this subject, published in the monthly journal of the Chamber of Mines of WA, 31st January, 1906, have described a method adopted by them in calculations made in connection with a series of trials of grinding pans. Their methOd is based upon the assumption that if a quantity Q of material consisting of particles of average diameter x be crushed down until the average diameter of the particles is y, then the work done in grinding is proportional to Q x. There is no theoretical basis for this assumption that the writer is aware of, and it does not appear to satisfy the fundamental conditions necessary. If the material be further crushed until the diameter 2 becomes Z, the additional work done is measured. The work done in crushing from diameter x to diameter Z in one operation is proportional to Q x:, and therefore we ought to have zx2 y2 x2 Q-+Q-=Q-. y2 Z2 Z2But these expressions are not in general equal to one another. In other words, according to the theory underlying this method, if we crush from diameter x to diameter y, and then from diameter...

Jan 1, 1909

Development of automatic fire protection systems for large, mobile mine haulage equipment was initiated under Department of Interior's Bureau of Mines-FMC Corp. contract H0122053, "Improved Sensors and Fire Control Systems for Mining Equipment June 1972 to May 1973." After successfully designing and mock-up testing an effective economical automatic fire protection system, and after having demonstrated that the system could extinguish controlled fires on 100-ton capacity haulage trucks, USBM-FMC contract 110232059 was issued in June, 1973, to conduct further development and validation testing. This report documents technical progress and activity under the latter contract. Figure 1 shows areas of the two haulage trucks that were protected by the automatic fire protection systems tested during this program. Figures 2 and 3 are composites showing hardware and schematic diagrams of the systems tested.

Jan 1, 1974

By J. O. Marsden, M. M. Botz

"Heap leaching is responsible for approximately 21 percent — 3.9 million metric tonnes — of copper production and 9 percent — 270 metric tonnes or 8.7 million ounces — of gold production worldwide. Given metal price assumptions of $2.25/lb for copper and $1,250/oz for gold, these portions of global production generate revenues of $19 billion and $11 billion, respectively. For heap leaching operations, small changes in metal extraction efficiency drive substantial changes in operating cash flow margins and affect project viability. Variances in actual metal production from budgetary forecast estimates can mean the difference between success (value creation) and failure (value destruction) for a heap leach project. Despite the importance of heap leaching for copper, gold and silver production worldwide, there are no clear standards or guidelines for developing heap leach metal production forecasts. There is considerable variation among copper and gold producers that apply heap leaching technology as to how such modeling and forecasting is applied at the operational level. There are a variety of different modeling approaches that can be utilized for this purpose. However, these vary in cost, complexity, time to implement, accuracy and credibility. This paper explores the options available for heap leach modeling, discusses the advantages and disadvantages of each approach, and provides guidelines/recommendations for an effective approach to modeling metal production at existing or planned heap leach operations. The paper also provides expected ranges of variation between actual and modeled production.Introduction and backgroundHeap leaching is fundamentally different from other methods used in the processing and extraction of gold, silver, and copper and other base metals. Considered globally, the technique represents a relatively modest portion of production compared with the primary technologies applied for copper and gold recovery. Approximately 21 percent of copper production is attributable to heap leaching techniques, as opposed to 79 percent by conventional crushing, milling, flotation, smelting and refining. For gold, about 9 percent of global production is obtained from heap leaching, compared with over 90 percent by various combinations of crushing, milling, gravity concentration, flotation and/or agitated cyanide leaching processes or, in the case of placer deposits, by direct gravity concentration and/or amalgamation. In cases where heap leaching is the primary source of metal production, the ability to accurately forecast metal production may be the difference between commercial success and failure for a project or operation. Heap leaching — of crushed or run-of-mine ore — is also commonly applied as a secondary process to treat lower-grade ores from a given deposit, such as at Chuquicamata in Chile, Cerro Verde in Peru and Bagdad in Arizona for copper extraction and at Twin Creeks and Carlin, both in Nevada, for gold. In such cases, heap leaching provides incremental revenue to supplement the primary process. Variances between actual and forecast metal production from heap leaching as a secondary process are typically tolerated and absorbed within the overall site metallurgical balance. In either case, accurate production modeling and forecasting creates significant value for heap leaching projects, is essential for managing production expectations — timing and volumes — and is likely to be a critical success factor for most heap leach projects."

Jan 1, 2017

By McIntosh A. H, Torlach J. A

Since the last paper on mining methods was presented to the Annual Conference of the Australasian Institute of Mining and Metallurgy in 1:960, numerous advances have been made in drilling and blasting techniques at Mount Morgan. This paper describes the drilling and blasting methods being employed in the open cut. The change over to track mounted percussion drills for all types of primary drilling is almost complete and new techniques such as detergent drilling and pressure loading of ANFO are being applied successfully.

Jan 1, 1965

I attended a funeral in West Monroe, Louisiana, for one of the best powder peddlers I’ve ever known. He started work in 1948 for Dixie Dynamite, a seismograph explosive distributor. His first job was as a truck driver, then magazine keeper and then sales re p re s e n t a t i v e . When Dixie Dynamite quit, he acted as an explosives sales agent for sometime before moving on to Kansas to be a sales rep for a distributor there. We called him the “ragin cajun” long before James Carville came on the national scene messing up things. While he was born in G e o rgia, he was a Cajun at heart. I don’t believe the old saying, “Build a better mousetrap and the world will beat a path to your door.” To me, the best products in the world need to be sold. Two examples of this are the Beta system for TV and the Apple Macintosh computers. Beta is the best system but VHS took over because the Beta people fell down on the selling job. Windows 98 is Macintosh ‘86 but again the engineers were not salesmen. Marion “Johnny” Johnson who was buried only about a half mile from his first magazine site proved that good selling is good citizenship. He could have sold any firstclass product, for he wouldn’t tolerate inferior items, and made a successful career of it, but he chose dynamite and the industry benefited from his talents.

Jan 1, 2004

By Pierre Rocque

The Red Lake Mine is located approximately 600 km northwest of Thunder Bay. This 545 tpd (600 tons/day) underground narrow vein gold operation is set to produce in excess of 14.8 tonnes (475,000 ounces) in 2001 at a cash operating cost below 75 U$/oz. The high-grade nature of this deposit (>55 g/t or >1.6 opt) coupled with its complex geological environment and relatively deep location dictated the choice of a very selective primary mining method, Mechanized Overhand Cut and Fill. In addition to geological challenges, mine design issues such as material handling, ground stability and requirements for yieldable ground support are also discussed in this paper.

Oct 1, 2001

Changes in reductant and energy inputs which are required to adjust the slag composition in an ilmenite smelter to a higher or lower FeO content are calculated. The calculated changes are based on the assumption that solidification equilibrium with the freeze lining constrains the slag composition to follow a eutectic groove in the TiO2-FeO-TiO1.5phase diagram. Calculated equilibrium conditions along the eutectic groove are presented, and form the basis of the calculations. The inputs of energy and carbon need to deviate strongly from the steady-state values to adjust the slag composition. The inputs required at any given time depend on the desired rate of change of the slag composition, and the current slag composition. The steady-state relationship of a change in energy input of 5 kWh corresponding to a 1 kg change in carbon input also holds for the changed inputs during transient changes in FeO content. Keywords: Ilmenite smelting, freeze lining, solidification, eutectic

Jan 1, 2003

Jan 1, 1988

By I. Nakatsugawa

Chemical conversion coating is a process to create thin oxide/hydroxide film containing several inorganic/organic compounds by way of chemical deposition reaction. In case of the application to Mg mobile electronic housings, the film should possess a good electric conductivity while keeping adequate corrosion resistance and working as a paint base. The use of toxic/hazardous chemicals is strictly prohibited from the environmental aspects. This paper describes the recent trend of conversion coating used for Mg electronic housings and analyzes critically from the point of surface technology. The importance of cleaning process and understanding of surface microstructure are particularly emphasized with several experimental results.

Jan 1, 2006

By Anthony T. Iannacchione

The Roof Fall Risk Index (RFRI) is a new method introduced by the National Institute for Occupational Safety and Health (NIOSH) to assist the underground stone mine operator in 1) assessing defects the mine strata and 2) rating the relative roof fall risk these defects pose. The RFRI utilizes observational techniques to identify defects in the roof strata caused by local geologic, stress, and mining conditions. Assessment values for ten defined defect categories provides the foundation for estimating a range of risk conditions between 0 and 100 that define the potential for a roof fall. This paper examines how the defect information is collected using two field verification sites and proposes methods to analyze the RFRI data. These examples provide information on how well the method replicates observed conditions and how it might be applied in practice.

Jan 1, 2006

By T. E. Gray

This report describes the preparation characteristics of the more significant coalbeds in Monongalia County, W. Va. It is one of a Bureau of Mines series planned to determine coals suitable for producing metallurgical coke, either as mined or after beneficiation. Over 9.5 million tons of coal was produced in Monongalia County in 1957, of which more than 7 million tons was cleaned mechanically in 8 cleaning plants. On January I, 1954 the Bureau of Mines estimated that 1,576 million tons of recoverable coal remained in the county in beds 28 inches or more thick.

Jan 1, 1960

By Randall M. Wheeler

It is important to be able to quantify the effects of blast delay designs on vibration characteristics. White was the first company to develop commercially available software, called Alpha-Blast, for this purpose. The program can indicate relative amplitude and frequency results to be expected from the use of particular delay intervals. If enhanced vibration effects from delays are a problem, a technique to evaluate this situation will be invaluable.

Jan 1, 1994

The excavation of ramps and tunnels often requires high-speed development with (or without) the use of high-energy mining equipment such as loaders, dump trucks, TBMs and roadheaders. This high-speed development creates a challenge in terms of providing a safe and productive working environment. For example, heat from continuously exposed surrounding rock, heat from broken rock, heat generated by mining equipment, potential in flows of hot ground water, pollution from associated diesel equipment and the distance of the advancing face from fresh through-ventilation all have to be taken into account when designing ventilation systems for high-speed ramp and tunnel developments. This paper discusses methods of achieving acceptable environments at the face and along the length of the tunnel. The methodology has been successfully implemented in the development of long (up to 20 km) TBM drives in the Lesotho Highlands Project and in mining projects in hot rock using drill and blast methods as well as mechanized methods using continuous miners and roadheaders. The determination of heat loads includes calculation of the heat flow within the surrounding rock, evaluation of the operating cycle of the equipment and the contribution to the overall heat load of the broken rock as it travels out of the tunnel. The determination of heat loads from surrounding rock in new tunnels required a modification of the algorithms generally used for established excavations. The paper also examines the use of, for example, mobile duct and fan systems to ensure that fresh air is delivered to the specific areas where workers are located.

Jan 1, 2000

By Marcus A. Wiley, Gregory Abramov

Borehole mining (BHM) is a remotely operated method of extracting rock material through boreholes by high-pressure water jets. Figure 1 illustrates a BHM tool and fluids circulation. The tool consists of at least two pipes, one for pumping down high-pressure water, the second for delivering slurry to the surface. This article reviews the BHM process. It discusses current and new applications for borehole mining and help the readers determine if BHM is applicable in their situations. Previous articles in ME about BHM explained either a particular project (ME, April 2001, pp. 33-36) or a newest patent in this area (ME, March 1991, pp. 313-318). However, neither one provided an overview on the modern BHM technology.

Jan 1, 2004

By Mishark Nnabuchi

A heterojunction of PbS - CuS thin film has been grown on glass slides by SGT. The films were annealed for 1hr at temperature of 373K and 423K respectively. The optical properties were characterized using a UNICO UV - 2102 PC Spectrophotometer at normal incidence of light in the wavelength range of 200 - 1000nm. The minimum percentage transmittance was observed to be 34% for sample A and 25% for sample B within the same optical region. The band gap energy was determined from the spectra to be 2.05eV for sample A and 1.85eV for sample B which gave a band shift of 0.20eV. It can thus be concluded that the optical properties of the films within the VIS - UV - NIR can find application in solar thermal technology, particularly as antireflection coating, window materials and as good materials for selective solar cell fabrication.

Jan 1, 2010