Search Documents

By Niels Krebs Ovesen

Close economic cooperation was established among the countries in western Europe during the seventies. As a consequence, among others, a need for harmonized technical specifications for civil engineering works arose. Technical specifications for design and execution of building and civil engineering structures exist in most of the European countries. In some countries such technical specifications are part of the building regulations and in other they are independent codes of practice and standards. The works on the Eurocodes was initiated by the Commission of the European Communities about 1976. The Eurocodes are intended as common unified design codes for different load bearing structures constructed from different materials. They are also intended to cover design of geotechnical structures. They are established with a view to promote the free movement of goods and services within the member states of the European Community - the so called Internal Market - and within the member countries of the European Free Trade Association, EFTA by removing obstacles arising from different rules for calculation and design.

Jan 1, 1994

By L. I. Gyrskia, Y. V. Andreev, T. N. Greiver, G. V. Petrov

Traditionally, chromite ores are regarded exclusively as a monomineral raw material for extraction of chromium. The results of the investigations indicate a wide range of PGM in the Ray-Iz chromites, amounting to 1-3 ppm PGM. The study of products of primary gravity concentration from heavily and lightly disseminated ores (Tsentralnoe deposit, Ray-Iz block), showed that the platinum-group minerals are concentrated in the tails and slimes of the processed products, containing 10-30 ppm total PGM. Preliminary data make it possible to conclude that an in-depth study of the platinum mineralogy of the Ray-Iz block chromite ores is necessary to develop a process that will produce both chromium and the PGM.

Jan 1, 2000

By Jerry Wallace

The goal: At an industrial site, sever a well pipe containing an interior obstruction in a timely, cost effective manner by using a shape-charge to cut through the casing more than 50 meters below ground surface from the outside, doing so while inside a larger pipe, without damaging the larger pipe. The problem: Pumps and retrieval tools stuck nearly 50 meters below ground surface inside a 305 mm diameter by 9.5 mm wall thickness water well casing. The well, depth of 185 meters, had to be inspected for contaminates then properly decommissioned before industrial expansion could take place overhead. The limitations: A 508 mm diameter pipe had been driven around the 305 mm pipe to a depth of 63 meters. The usable internal diameter of the larger pipe was about 480 mm while the smaller pipe had buckled at one point forming a 350 mm wide spot. The charge thickness was limited to less than one-half the difference. Additionally, water that filled the annular space between the two pipes had to be displaced for the charge to work properly. The solution: Enlist the support of the shape-charge manufacturer to design, build and test a charge to work under the conditions present, then make it work in the field.

Jan 1, 2000

By R. L. Grunes, F. K. Kies, C. D&apos, Antonio

THE several studies concerned with the annealing of thin nickel films have largely been restricted to films of a single thickness.1-4 It is well-known, however, that both physical and mechanical properties depend upon film thickness.5, 6 The strength-thickness relations found in vapor-deposited nickel films in the annealed and as-deposited states, as an example, are at least partially due to the density and arrangement of imperfections within the films.7, 8 For these reasons, the annealing characteristics of thin nickel films as a function of thickness were investigated. Electrical resistance was chosen to monitor annealing behavior since resistance changes are partially dependent upon defect structure. In addition, the equations predicting film resistivity as a function of thickness are already available.9, 10 Further advantages afforded by electrical-resistance measurements are its adaption to continuous readings during annealing and its relative simplicity. Nickel films were vapor-deposited, at average rates of 60Å per sec, on Vycor substrates held at room temperature in vacuums of about 10-5 torr. Afterwards, deposition-thickness measurements were made using a multiple-beam interferometric technique. A more detailed description of deposition procedures and the interferometer appear elsewhere.7, 8 The four-probe method was employed in measuring electrical resistance since this technique measures film resistance without contributions from lead wires and contacts. Resistance measurements were made before, during, and after annealing to temperatures of 700°C under vacuums of approximately 10-4 torr. Measurements were made every 25°C or more often when necessitated by unusual resistance changes. Cooling and heating rates were maintained at approximately 5°C per min. Typical resistivity vs temperature curves are shown in Figs. 1 through 4. It is apparent from these

Jan 1, 1965

Consents Required for Overseas Persons Overseas Investment Regulations 1974 Foreign investment proposals must be reviewed by the Overseas Investment Commission to ensure that these are in accord with national interests. Consent must be obtained from the Commission for: 1. New investment proposals which include: a. An overseas person acquiring 25 per cent or more of any class of share in a company. b. A New Zealand company issuing shares to an overseas person where this will result in that person owning 25 per cent or more of the company. c. An overseas person acquiring business assets for consideration in excess of $100 000. d. An overseas person commencing business in New Zealand. 2. Borrowing in New Zealand: An overseas person must obtain consent to raise funds in excess of $300 000 in New Zealand. 3. Borrowing Overseas: New Zealand incorporated companies must obtain consent to borrow overseas. Current policy is borrowing will be approved where the loan is for a specified fixed term of one year or more.

Jan 1, 1982

By Edward D. Graf

Once the heavy work of mining, supporting and completing an underground structure is finished, there is frequently the problem of handling unwanted water infiltration into the opening. Methods of controlling the infiltration vary from collecting and channelling the inflow to shutting off the water at the surface of the opening or within the ground formation. Discussed are various methods of controlling ground water inflow from within the structure including collector pipe systems, shotcrete, cement grout, bentonite, and various chemical grouts. Case histories illustrating some of the methods and materials will be presented.

Jan 1, 1987

By J. N. Van der Merwe

The results of over 900 coal strength tests done during the period 1993?1994 for the SIMRAC project COL021A were re-analysed with a view to find a method to delineate areas or seams that can be grouped together for analyses of coal strength and strength decay characteristics. It was confirmed that the strength of a coal specimen increases linearly with increasing diameter-to-length ratio and decreases exponentially with increasing size of specimen. However, by extrapolation of the data, it was shown that beyond a diameter of approximately 2 m, the size effect is insignificant. For larger specimens, the diameter-to-length ratio (referred to as the width-to-height ratio for full scale mine pillars) alone continues to influence the strength. The slope of the linear strength vs. diameter-to-length ratio relationship is independent of the size of the specimen and is not unique for coals from different mines. However, the intercept of that relationship is unique and is a function of specimen size. This offers a previously unknown method to distinguish between the coals from different mining areas and coal seams. Ranked from weakest to strongest, the samples tested from the different mines are in the order shown below, which roughly corresponds to the judgement of practising rock engineers in the field: ?Sigma ?ZAC ?Goedehoop ?Kriel ?Bank ?Blinkpan ?Secunda ?Greenside Arnot ?Khutala ?Delmas

Jan 1, 2003

By G. A. Wancheck

Shear tests were performed on several prepared samples of granular and powdery bulk materials to investigate the following parameters: Particle size and distribution, particle movement, moisture content, consolidation of material, bulk density, void ratio, porosity, volume change, and strain rate. A series of shear tests was performed with weight-percent-ratios of minus 0.185-inch tertiary sand and 1-1/2-by l/2-inch tertiary gravel mixtures, and weight-percent-ratios of minus 200-mesh limestone (rock dust) and minus 200-mesh bituminous float coal dust. A comparison was made for shear test results obtained with rectangular and circular shear cells utilizing the large and small direct shear testers. Specifically, the shear results obtained include the angle of internal friction or shear strength of the tested material under known consolidating pressures, and the kinematic angle of friction or coefficient of friction between the interface of a bulk material and a sample wall material. The experimental procedure, tests, and results are given for each parameter investigated.

Jan 1, 1973

By John Lindsay

"Although diamond mining is a relative newcomer to the Canadian mining industry, with the first diamond mine coming on stream in 1998, Canada is already a significant producer of high quality diamonds. This paper will review diamond production trends and highlight some of the projects currently under development, which have the potential to enhance Canada’s role as a significant diamond producer.Diamond recovery plants generally incorporate well-established mineral processing and recovery techniques, with issues such as product security, cut-off sizes, and diamond preservation becoming important considerations when developing process flowsheets. A diamond processing plant must achieve three key objectives, namely:• Liberation of the diamonds from the host rock;• Separation of the heavy minerals, which include the diamonds, from the host rock;• Recovery of the diamonds from the heavy mineral concentrates.Processing technologies and equipment commonly utilized in diamond processing plants will be reviewed and some of the significant issues associated with each option briefly discussed.Typical process flowsheets will be presented.Finally, an overview of De Beers’ Victor diamond project, located in northern Ontario, will be provided. This potentially significant diamond producer is currently at a pre-feasibility stage of development.DIAMONDS IN CANADAWorld Diamond ProductionCommercial diamond mining commenced in earnest with the discovery of the Kimberley diamondfields in South Africa in the late 1800s, and this resulted in a dramatic increase in the supply of diamonds. As can be seen from figure 1, world diamond production, mainly from South Africa, Angola, Congo, and Namibia, remained relatively constant through the early 1900s until the development of the large Russian kimberlite pipes in the 1950s. Production increased again in the 1960s and 70s with the development of the Botswana mines, but the most significant increase in global production came from the Argyle mine in Australia, which came on stream in 1983 and produced a peak of almost 43 million carats in 1994, representing approximately 40% of the world market. Production from Argyle has since fallen-off as grades have declined and the strip ratio has increased with the deepening of the open pit."

Jan 1, 2003

By H. Michael Breza

Texasgulf Inc. installed bucketwheel excavators and overland conveyor sysems at its Aurora, NC phosphate mine o increase the productivity and flexibilty of the surface mining operation. This ;ystem has significantly improved overrall. Its flexibility is evidenced by adapation to operation requirements, such is mining area moves, movement of xcavated overburden to designated ites, selective handling of overburden, poll placement contouring, and proiding an environmentally sound and afe operation. The system's productiv:y is evidenced by case studies relating. overall production, excavation rates nd cost-effectiveness. There are many competing alternaves available for excavating uncon)lidated overburden: truck-shovel, raglines, dredges and bucket wheel ticavators. These alternatives also may used in tandem to recover reserves icated at greater depths.

Jan 1, 1993

By J. H. Daniel

This report, summarizing the results of two studies sponsored by the Bureau of Mines, presents information on the types of mobile machines used in surface coal mines in the United States, and the amount of noise to which miners are exposed. Data consist of a calculated value of the probability of noise overexposure caused by specific equipment. These data are extrapolated to estimate the number of overexposed operators. Bulldozers were identified as the major contributors to noise overexposure, and the report presents results of a Bureau-funded program on the feasibility of providing retrofit noise control on bulldozers.

Jan 1, 1980

By M. R. J. Wyllie, Michael A. Torcaso

With the continued deep drilling of today, increasing numbers of high pressure and high temperature gas-condensate reservoirs are being discovered. Correspondingly, the ranges of properties of gas-condensate reservoir fluids are also being increased. The literature1*'." contains several excellent reviews of the property ranges in presently known condensate reservoirs. When one examines these property ranges, it becomes apparent that the need for reliable data is great if the engineer is to evaluate properly or appraise a gas-condensate reservoir. It is the purpose of this paper to present phase-behavior data that will point out some of the important variables that influence recovery from gas-condensate reservoirs produced by pressure depletion. All these variables may be resolved into two major categories: the hydroc:arbon composition of the reservoir fluid and the physical properties of the reservoir. But the variables which we will consider are those which are usually determined from well tests shortly after discovery and are, consequently, readily available to the engineer. They are as follows: (1) the producing separator gas-stock-tank liquid ratio, (2) stock-tank liquid gravity, and (3) reservoir temperature. Laboratory depletion studies have been performed on several reservoir fluids to illustrate the effect of changes in the cronsidered variables upon ultimate recoveries. The deviation factors, Z, of a series of reservoir fluids were determined experimentally to illustrate their order of magnitude and their effect upon the calculation of in-place reserves existing at high pressurcs and temperatures. The procedures followed in conjunction with the performance of these studies and their associated calculations are illustrated in Fig. 1. For the purpose of this paper, the depletion recoveries are expressed only in terms of pcr cent of initial stock-tank liquid, with the abandonment pressure assumed to be 500 psig. VARIATION OF RECOVERY WITH INITIAL PRODUCING SEPARATOR GAS-STOCK-TANK LIQUID RATIO The producing separator gas-stock-tank liquid ratio has long been one of the principal criteria in assumptions and generalized correlations' used for the estimation of ultimate recovery from gas-condensate reservoirs. Fig. 2 presents a plot of the cumulative recovery of stock-tank liquid at abandonment as a function of the initial producing separator gas-stock-tank liquid ratio. The graphical illustration represents the results of 44 laboratory depletion studies performed on actual gas-condensate fluids. These data are presented not only to illustrate the general trend of ultimate recovery increase with initial producing ratio increase but to emphasize the considerable variation in possible recovery at any given producing ratio. Table 1 presents the properties of two actual reservoir fluids chosen to illustrate the approximate extremities of producing ratios for gas-condensate systems. The fluids designated as A and B exhibited initial producing ratios of 3,400 and 114,000 scf/bbl, respectively. Fig. 3 presents a graphical comparison of the cumulative stock-tank liquid recoveries, calculated from the well-stream compositions and produced volumes for each fluid during depletion. It is to be noted that Fluid A exhibited a recovery of only 16.5 per cent when produced to an assumed abandonment pressure of 500 psig while the corresponding recovery for Fluid B was calculated to be 62.2 per cent. This difference in recovery, which exemplifies the general trend of recovery increase with initial producing ratio increase, is readily explained by consid-

By Kenneth C. Ko

An engineering investigation was carried out on the technical and economic feasibility of implementing flexible liner/backpacking support systems In an advancing tailgate longwall mine. The system for a model mine consists of a circular tube constructed of liner plates and flyash backpacking. Flyash is pneumatically stowed into the tailgate. Small amounts of cement may be mixed to improve the support capability of the fill In difficult local ground conditions. Water is added inside the nozzle immediately prior to spraying. Results of theoretical analyses and a field test show that the designed system is technically feasible, can be cost-competitive, provides more stable ground conditions, and can Increase productivity and coal recovery, when compared with existing retreat longwall systems. In certain mine layouts, the new system can reduce the direct mining costs by a significant amount. The system would be particularly applicable to deeper coal beds with bad ground conditions.

Jan 1, 1980

By N. Yamazaki

The supply of clean copper ores, which have high copper concentration and low impurities like arsenic, has declined year by year. Therefore, both mine and smelter sides have to consider how to remove impurities like arsenic. We focus herein on arsenic as an impurity because it is an extremely important issue from the environmental point of view. Approximately 150,000 t of arsenic is input into the copper industry every year. A small part of it is mainly treated in the smelting side. For instance, Ministro Hales Limited, which is a mining corporation in Chile, has performed the calcination process to remove arsenic from ore with high-arsenic content. In the process, flue gas is washed by water, and the final residue is treated by a hydrometallurgical process. Many processes for arsenic removal in various stages have been proposed, and several bottlenecks exist to achieve it. One of the difficulties encountered is getting an assessment of the process, which depends on the countries and/or areas of operation. The standardization of the assessment procedure will be desired in the near future to keep the same environment standards all over the world, and now is the time to start making discussions on this matter. This will be the first step in making an international assessment procedure for arsenic treatment in the copper industry. INTRODUCTION Using the term “sustainable development” without any scientific basis can give people a false sense of security. Engineers and scientists must analyze the total mass flow of energy and materials and estimate local drain on the environment as well as the global impact of a particular industrial activity to ensure sustainability on this planet. The operations of the mining and smelting industries have a strong effect on the environment even if they provide useful materials for human beings. The copper mining and smelting industries have brought about serious environmental problems in the past. For example, the Ashio mine pollution caused big damage to the agricultural sector near the Ashio area in Japan in the late 19th century. One of the most serious problems at that time was SO2 emission because copper ore is sulfide, and the smelting process basically results to sulfur oxidation. The resource balance from a copper smelter in a year, assuming a total production of 16 million tons, can be summarized as follows: discarded minerals, 30 billion tons; sulfur, 16 million tons; iron oxide, 8 million tons; additional smaller amounts of other metals, electricity, and fuel.

Jan 1, 2019

By Mick Fritz, Tom Treleaven

The success of any blast is dependent on the accuracy of the blast design and field controls placed at the shot location. The procedure by which the data is collected and analyzed is paramount to accomplishing the anticipated blast results. lf the geometry of the blast is not measured correctly, then the results will not meet expectations. Measuring the geometry and compensating for bole hole deviations is crucial not only to the lnitlal blast but also for any consecutive blasts. Excessive bore hole deviation can cancel any new technology in use. However the instruments and skills required solving this Issue are readily available.

Jan 1, 1998

By David J. Kusler

This study is an appraisal of the feasibility of recovery and the possible chemical and physical uses of the limestone from the Greenbrier Formation in western West Virginia. Data on minability, occurrence, quality, and markets were obtained from published and unpublished sources and by a limited mail survey combined with personal contacts. The estimated costs of recovery by deep mining techniques are considerably higher than competitive surface and shallow subsurface operations. Compositional in formation available for this study was limited but indicated the suitability of the limestone for most physical uses and some chemical process uses in appraisal of the uses and demand reveals that immediate markets may be difficult to establish, but for some uses long-term prospects may be encouraging, especially if the quality of limestone would be suitable for lime manufacture or use as metallurgical fluxstone.

Jan 1, 1968

By R. Codell, D. L. Hughson

While benchmarking the integrated finite-volume code MULTIFLO against the analytical solution of Philip et al. (1989) for cylindrical underground openings, we found numerical simulation of dripping threshold flux consistently higher than the analytical solution for both rectangular and unstructured grids. The magnitude of error is proportional to the alpha parameter characterizing capillarity. This may bias estimates of repository performance towards non-conservatism.

Jan 1, 2000

By C. F. Vos

Small replacements of C12-trithiocarbonate (C12-TTC) for dithiocarbonate (DTC)/dithiophosphate (DTP) in a reagent suite for the flotation of platinum group metals (PGM) have significantly improved the rejection of gangue. Coupled to this is an improvement in kinetics, grade and recovery of PGMs. In a pilot-plant trial, after a 5 mole per cent replacement of the current DTC/DTP collector combination by C12-TTC, large opaque bubbles were replaced by small clear ones. In addition, a similar flotation response was realized with one-third of the current depressant dosage. During a preliminary plant trial on underground UG2 ore, the initial rougher concentrates were characterized by higher PGM concentrate grades and this was in part due to improved chromiter ejection. The concentrate produced from the TTC trial also exhibited a much finer particle size distribution. The overall circuit performance, which included secondary regrind and flotation, showed an increase in concentrate grade of approximately 44% while the tailings grade remained unchanged

Jan 1, 2007

By R. O. Suominen, P. A. Taskinen, K. R. Lilius, A. T. Jokilaakso

Chalcopyrite concentrate was flash-oxidised in a laminar-flow furnace in oxygen-nitrogen atmospheres that ranged in composition from N2 to N2 + 50 vol% O2. Gas pre-heating temperatures were 500-1100 degrees C and four particle-size fractions were studied: 28-38, 38-44, 44-62 and 62-74 micrometres. The effect of the residence time of the particles on sulphur removal was studied in the range 0.1-0.35 s. Scanning-electron microscopy combined with energy-dispersive analysis and back-scattered electron analysis was used to determine the morphology and mineralogy of the reacted particles. Total desulphurisation was achieved under the most oxidising conditions. Particles were observed to undergo fragmentation during oxidation, the violence of this depending on the iron and sulphur contents and the original particle-size fraction. The melting and/or reaction stages of the particles under different conditions were studied in powder samples. Polished sections were examined to follow the development of porosity and the mineralogy of the particles. A model for the fragmentation process is described

Jul 1, 1991

By Sterling J. Anderson

To define the technical competence and capabilities of a nonexplosive excavation concept, the Bureau of Mines conducted reduced-scale laboratory tests of a mechanical excavation tool called a rock splitter. Hydraulically actuated splitters, capable of generating both radial and axial loads on a predrilled hole, were designed and fabricated. Through paired variable testing and drifting simulation, reduced-scale splitter performance was evaluated in concrete. Testing proved that the rock splitter is capable of excavating within the highly confined drift set-ting and that it offers a distinct advantage over splitters that can generate radial loads only.

Jan 1, 1982