Search Documents

By R. C. D. Phillis

Conventional stoping in hard rock mining is largely considered an operational environment. This paper suggests that stoping falls within the realm of a project management environment typified by uncertainty, variation, and large numbers of interdependencies. Stoping was then equated to a micro-project with many simultaneous activities that had to be executed accurately using finite resources within limited shift durations in order to reach specific goals. Critical chain project management (CCPM) principles were applied to the stoping activities, and the results showed that the number of blasts per panel can be significantly increased by successfully moving the distribution of work as close as possible to the start of shift. Critical chain principles also assisted in facilitating re-focusing and teamwork among stoping crews as well as between day- and night-shift crews. The main recorded success was in managing inherent protective capacities/local contingencies/fat/buffers that are found in all projects. The impact on mine health and safety (MHS) was significant as individual operators and crews became convinced that they could perform all stoping tasks (activities) without compromising accuracy or speed.

Jan 1, 2011

By David E. Nicholson

In a Bureau of Mines investigation of the dynamic compaction of mine hydraulic backfills, two basic forms of mechanical vibration inducers were used and compared for effectiveness of compaction. Internal compaction, using concrete probe vibrators of various sizes, and external compaction, using plate vibrators} were studied and evaluated for use in underground stopes. An aluminum plate, which was light and displaced sufficient volume to remain afloat in fluid fill, and a steel plate were both used in the external compaction tests. Efficiency of compaction was better in studies conducted with internal probe vibrators. Tests were conducted in an underground backfilled stope with three different-sized probe vibrators (2-, 4-, and 6-inch-diameter) to determine an approximate area of influence. Results showed the areas of influence to be approximately 3, 4, and 5 feet in diameter, respectively, for the three different probes. Physical properties of hydraulic slurries were determined; preferred grain-size distributions, water exudation properties, and water contents of hydraulic slurries are reported. The best compaction results were obtained with moderately well-graded, fully saturated backfills, with slow rates of water exudation, which were capable of remaining in a semifluid state during the compaction process.

Jan 1, 1967

By M. Bennett, L. Twidwell

Montana Tech has embarked on a coordinated series of studies to delineate the characteristics of the Berkeley Pitlake containing over 36 billion gallons of acidic, metal-contaminated water formed after the cessation of open-pit copper mining in Butte, Montana, USA. The objectives of the overall series of studies are to summarize presently available information and to generate new and needed information to formulate a conceptual environmental model for the pitlake and to provide characterization data for the development of advanced treatment technologies. In this presentation, the chemistry of the Berkeley Pitlake water is partially reviewed. It is known that the pitlake consists of two distinct layers of water referred to as surface and deep water. Samples of deep water were collected and placed in a 12-ft high and 6-inch diameter column and exposed to different wavelengths of UV radiation as well as atmospheric conditions. Measurements of pH, redox potential (EH), dissolved O2, turbidity, conductivity, temperature, and elemental composition show that the water reacts differently and indicates that the diurnal effects of sunlight likely play a major non-biological role in its chemistry. Resulting technology could be useful for developing an alternative to treating acid-rock drainage.

Jan 1, 2007

By C. A. Geffen

This report, sponsored by the U. S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the com¬ponent operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By Benoit Virollet

Over the last 10 years the diameter of unbraced, unlined and unanchored circular shafts has grown dramatically in many parts of the world. This progress has taken place through improvements in: construction methods; concrete rheology; and design capabilities. Excavation equipment has become more precise in terms of operator control and ability to correct alignment of digging elements leading to better alignment tolerances. Also contributing to the increases in shaft diameters is the evolution of design models. A better understanding of soil structure interaction is being incorporated into the analyses in terms of radial soil stresses and imposed loads on the shaft. This paper provides an overview of the recent progress made in circular shaft construction, the primary design considerations, and some innovative uses of efficient arc elements to develop unsupported structures of other shapes. In addition, a summary of recent circular shafts constructed worldwide is provided.

Jan 1, 2006

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been-published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment. Report of Investigations 3309, Permissible Electrically Operated Air Compressors, which contains similar information, was issued in August 1936, and a Report of Investigations 3326, Permissible Electrically Operated Room Hoists, was issued in January 1937. Thus, the present paper is the third to give detailed information concerning permissible machines of types not included in bulletins, and covers all the rock-dust distributors approved prior to October 1, 1936.

Jan 1, 1937

By Mike Robotham

When RFQ?s are received they often contain detailed technical specifications which suggest a departure from the suppliers own customary approach to the design. Both client and end user are quite rightly influenced by their own experiences. The question is who is right, the client and his consultant, the supplier or perhaps a combination of these. This paper looks at some of the fundamental variances that often occur in the approach to the mechanical design of drum hoists, based on our experiences of recent years. Director of Engineering, Mike Robotham is a chartered engineer and has been with DavyMarkham for over 30 years. Having completed a craft apprenticeship he later joined the engineering department as a junior engineer. He has a wealth of experience of working on medium to large engineering projects in the field of mechanical, electrical and hydraulic equipment

May 1, 2011

A Study on Main and Interaction Effects of Operating Variables of Column Flotation

Sep 13, 2010

THE flotation plant at Mount Lyell was erected, primarily, for the treatment of ore from the Lyell Comstock mine. These workings are situated over a mile in a direct line north of the North Mount Lyell mine, and are connected with the Reduction Work at Queenstown by a 2-ft. gauge steel tramway via the Queen River valley a distance of 7 miles. The property was purchased from the Mount Lyell Comstock Copper Co. After the disastrous fire in the North Mount Lyell mine in October, 1912, steps were immediately taken to make Lyell Comstock ore available for treatment, in order to relieve distress caused by any prolonged stoppage of work, and subsequently 13,032 tons of ore, averaging 3.38 %copper, 0.28 oz. silver, and 0.034 oz. gold; were smelted. When operations were resumed at the North Mount Lyell mine, it was evident that there was no economic advantage in smelting Lyell Comstock ore as compared with the higher value North Mount Lyell ore, which was also a better flux for the Mount Lyell pyrites, and that the future of the Lyell Comstock ore depended upon cheap mining and successful concentration of the ore. Therefore, extensive trenching and diamond-drilling was carried out, and a sufficiently large quantity of ore proved available for cheap extraction by open-cut methods. At the same time bulk tests by flotation were carried out at the Minerals Separation testing plant in Melbourne on different classes of ore from the Mount Lyell Comstock mine proper, followed by laboratory tests at Queenstown on all classes of ore available. All these tests demonstrated that the ore was amenable to the process, provided that it was ground finely enough. Plant erection was delayed by the general dislocation of business at the outbreak of war, but finally it became...

Jan 1, 1920

In this paper a numerical formulation is presented for determination of the axial load along a cable bolt for a prescribed distribution of rock mass displacement. Results using the program CABLE indicate that during excavation, the load distribution that develops along an untensioned fully grouted cable bolt depends on three main factors: (i) the properties of the cable itself, (ii) the shear force that develops due to bond at the cable-grout interface (i.e. bond stiffness), and (iii) the distribution of rock mass displacement along the cable bolt length. In general, the effect of low modulus rock and mining induced stress decreases in reducing bond strength as determined from short embedment length tests, is reflected in the development of axial loads significantly less than the ultimate tensile capacity even for long cable bolts. However, the load distribution is also dependent on the deformation distribution in the reinforced rock mass. Higher cable bolt loads will be developed for a rock mass that behaves as a discontinuum with deformation concentrated on a few fractures, than for one which behaves as a continuum, either due to a total lack of fractures or a very high fracture density. This result suggests that the stiffness of a fully grouted cable bolt is not simply a characteristic of the bolt and grout used, but also of the deformation behavior of the ground. In other words, the same combination of bolt and grout will be stiffer if the rock behaves as a discontinuum than if it behaves as a continuum. This paper also explains the laboratory test programme used to determine the constitutive behavior of the Garford bulb and Nutcase cables bolts. Details of the test setup as well as the obtained results are summarized and discussed.

Jan 1, 1996

By Victor C. Bryan

One of the most sought after answers in any consideration of blasting activities relative to mines and quarries is how to safely and efficiently use explosives. While that discussion might be relatively straightfonvard in a “site specific” situation. it becomes more complex when viewed from a broad geographic perspective. Such is the case in considering the operations of one United States producer of crushed stone with surface and underground mines spread over a thirteen state area. Differing geologic environments set conditions that dictate to the blaster as now specifically to get optimum results from the blast hole. This treatise is a discussion of the various methods, materials, and principles used in conducting such blasting operations.

Jan 1, 1991

By Carlos F. Perucca

"Potassium is one of the three basic plant nutrients along with nitrogen and phosphorus. There is no substitute for potassium compounds in agriculture; they are essential to maintain and expand food production.Potash is extracted from buried ancient evaporites by underground or solution mining. This accounts for most of the potassium produced. Another important source is brine from landlocked water bodies, such as the Dead Sea, Salar de Atacama or Great Salt Lake.About 95% of potash produced worldwide is used in agriculture. The rest is found in several other industrial uses, including glass manufacturing, soaps, plastics and pharmaceuticals.Currently, three producers: IMC, PCS and Agrium operate 8 conventional and two solution mines in Saskatchewan, five of which run froth flotation circuits, two heavy media-flotation, two run forced crystallization and one natural crystallization.Potash in SaskatchewanPotash was discovered in Saskatchewan in the early 1940’s while drilling for oil. The deposits lie diagonally across the southern plains of Saskatchewan sloping southerly from a 1,000m depth at Saskatoon to more than 1,600 m depth at Belle Plaine and up to 3,000 m in depth in North Dakota. The known deposits are massive, accounting for more than 40% of the world’s known reserves."

Jan 1, 2003

By Charles S. Robinson

INTRODUCTION Geology, the science of the earth, is the fundamental science in the construction of a tunnel. The approximate site of a tunnel is determined by its purpose. The geology of the tunnel site will determine the cost--or feasibility of a tunnel--the specific alignment to accomplish the purpose of the tunnel, the design of the tunnel (within the limits of the purpose of the tunnel), and the methods of construction. The more accurately the geology of a proposed tunnel can be depicted, the more accurately can the cost of a tunnel be estimated. The factors that should be defined for tunnel design and construction are the physical characteristics of the material in which the tunnel is to be constructed. The physical characteristics of the material are determined by the genesis of the material, and subsequent geologic processes that have affected the material. The geologic materials in which tunnels are constructed can be broadly classified as unconsolidated and consolidated. The unconsolidated materials include chiefly deposits of recent geologic time that occur near the surface. Because these deposits occur near the surface, and tunnels constructed in them will be at shallow depth, methods of physical exploration such as geophysical methods, trenching, and drilling will give more data at relatively low cost--therefore the physical exploration is generally, or should be, quite extensive--and the

Jan 1, 1997

Industrial Minerals production in New Zealand is limited in both quantity and range, but imported in quantities that make New Zealand the world's biggest consumer per head of population. The use of industrial minerals is assured as both population and standard of living increase regularly. But to develop these minerals in the New Zealand environment requires the mineral, or its market (both local and export), to have characteristics that negate the remote geographical location. Volume and/or uniqueness can achieve this.

Jan 1, 1997

By David Bigby

In the UK, it is becoming increasingly necessary to open new longwall mining areas above old, abandoned workings. In such cases, strategic and gate roadways must often be driven and maintained across highly stressed areas and pre-existing and sometimes only recently formed subsidence troughs. Ground control at the edges of the subsidence trough can be particularly problematic, with complex combinations of stress and rock conditions being encountered depending upon the precise position in relation to underlying pillar edges. For economic recovery of these reserves, it is essential that rockbolt support is used wherever possible. It is therefore very important to the industry to develop its understanding of ground conditions and support requirements in these areas. This paper describes; ? the historical background to these problems and a series of documented UK case studies from the last 20 years. ? the experiences at UK Coal?s Riccall colliery, where a number of longwall panels were worked at a depth of around 800m, some 65m above previously worked longwalls. Actual experience is compared with pre-mining expectations and model predictions. ? design considerations and experience to date at UK Coal?s Welbeck and Thoresby collieries, which are embarking upon a series of longwalls in the Deep Soft seam, 30-40m above previously worked longwalls. The paper outlines numerical modelling techniques used to optimise such mine layouts within the complex geological and geometric constraints of a mature coalfield. These involve combinations of 2D and 3D finite difference and 3D boundary element models. It also discuss new modelling approaches which will be investigated in forthcoming EU funded research.

Jan 1, 2007

By Lam. E. K., J. W. Jarvi, B. P. Bharadwaj

"The Rabbit Lake Operation is located in Northern Saskatchewan on the western shore of Wollaston Lake approximately 800 km north of Saskatoon, Saskatchewan.The Operation is owned by a joint venture of Cameco Corporation and Uranerz Exploration and Mining Limited. Cameco is the operator.The Mill started production in June 1975 under the ownership of Gulf Minerals Canada Limited and over the past twenty years has increased the rated production capacity to over twice the original design.The Mill was originally designed to process 485,000 tonnes per year of ore with an annual production of 2.0 million kg of U308 (yellowcake). During the past ten years changes in ore sources and process modifications have led to increased milling capacity and production targets. The Mill has treated a total of 8.6 million tonnes of ore and produced over 40 million kg of U308 in the twenty year period, despite the shutdown and cutbacks in operating time since 1989.The 1995 tonnage throughput was 206,000 tonnes per year. Annual production though has risen to 3.6 million kg of yellowcake despite the departure from full-time to half-time operation in 1991 (7 up-7 down). The forecast for the coming years will see tonnage rising from 300,000 to 570,000 tonnes, production of 4.5 to 5.4 million kg of yellowcake and an anticipated return in the year 1998 to full time operation.This paper will give a brief history of the Mill and focus on the present flowsheet and recent improvements to the process."

Jan 1, 1996

By H. Hearnden

Whereas in the past, ladles were simply a means of transferring molten products from furnace tapholes to points of discharge be they casting pans or waste dumps, the ladle is now becoming a more integral and versatile piece of equipment in the pyrometallurgical plant. The drive behind this development is the need for continuous improvement in performance where better, faster and cheaper means remaining competitive in the global market. This paper will explore the technologies available for the rendering of a costly and otherwise cumbersome piece of pyrometallurgical equipment more efficient and versatile in adding value to the final product. Essentially it all revolves around heat and more importantly the loss of it when tapping. The common practice is to move the molten product to its point of discharge quickly with the minimum of interruption to prevent skulling and hence the cost associated with clearing it. The advances in Oxy-fuel burners, AC or DC ladle furnaces, converters, gas purging and high velocity, bath injection systems has increased the versatility of processes and enhanced the potential for adding value to intermediate products through down stream practices such as granulation and atomisation.

Jan 1, 2004

GENERAL CONTRACTOR: ALEXANDER CONSTRUCTORS, INC. STRUCTURAL ENGINEER: CAGLEY & ASSOCIATES, INC. GEOTECHNICAL ENGINEER: F.T. KITLINSKI & ASSOCIATES, INC. PILE FOUNDATION CONTRACTOR: L.G. BARCUS AND SONS, INC. PROJECT PROFILE: 108-10 in. diameter AugerPiles installed to an approximate depth of 32 ft. Piles were installed through Stiff Clayey Fill and Medium-Dense Sands to Decomposed Shale. Piles were drilled to a refusal criteria of 1 ft. / 3 min. Piles were installed using a Barcus Mantis AugerPile rig which is large enough to install piles 25 to 50 ft. long outdoors. The Mantis is also ideal for indoor and low overhead installations. On top of being extremely versatile, the Mantis is also very economical to mobilize. The existing structure is supported on H-Piles. The AugerPiles were furnished and installed for less than the material price of the H-Piles. Design loads were under 40 tons which eliminated the need for a load test. AugerPiles were selected for minimal vibration, limited noise, and economy.

Jan 1, 2001

By W. L. Garrison

Improvements continue to be made in rapid excavation and tunneling technology. There are several ways to examine the impacts of such improvements. The most common procedure is to monitor current developments and to evaluate prospects for expansion of present types of uses. Other approaches are called for, however, if the technology might be used in ways not now imagined, if the search is for information for managers of technology development, and if the issue is that of the wise use of the technology by society. The first section of the paper will pose these matters as questions. These questions will be examined from the point of view of the processes of technology development and utilization, and then further examined against the backdrop of processes at work within the urban area. Such an examination will provide insight into the way technology developments should proceed. The final section will present some comments that may be useful to those guiding the development of the technology and to those who might provide leadership for its wise utilization. THE QUESTIONS Three questions are posed: 1. Are there uses for the technology beyond further penetrations of its present markets? 2. Can information be supplied to managers of technology development so that they may improve the assignment of priorities among development choices? 3. How can society make wiser use of the technology?

Jan 1, 1974

By N. Simpson

Low carbon 11.5% chromium stainless steels are finding increasing use in industry as square or rectangular tubing material for the construction of structures by welding. During processing, resistively welded circular pipes are bent into square or rectangular shapes. During this process longitudinal cracks can sometimes develop atone of the inner corners of the section. An investigation has shown that the processing of round into square tubing with very sharp corners can cause excessive cold working at the inner corners of the squared tube. This, together with the high tensile residual stresses and a susceptible microstructure due to the presence of grain boundary carbides, can result in brittle cleavage cracking. Measures that can be used to reduce the problem are described.

Jan 1, 2003