Search Documents

By Lyon R. J P

The quartz-cassiterite-wolfram veins at the Aberfoyle Tin Mine, north-eastern Tasmania, form a sheeted zone about 200 ft. wide and 1,600 ft. long in slightly contact metamorphosed shales, slates and greywackes, and are associated with a cupola of aplitic granite whose top is about 1,050 ft. below the present surface. Economic mineralization persists from the surface down to a vertical depth of 1,050 ft. to 1,100 ft., dying away in the vicinity of the cupola. Down to the 9-level there is a progressive increase in wolfram content of the veins, and a decline in cassiterite content, with increasing depth.The veins are banded or zoned, with a seivedge of muscovite on the wall. Cassiterite, wolfram and sphalerite occur inside the selvedges, projecting into a core of quartz of varying width. Other sulphides form the central part of some narrow veins, or occur as clots in the quartz. The general sequence of deposition of the ore minerals was: (1) cassiterite, wolfram; (2) arsenopyrite, pyrite, molybdenite; (3) pyrrhotite (in part); (4) blende-group minerals-chalcopyrite, sphalerite, stannite, pyrrhotite (in part)-as solid solutions; (5) galena, tetrahedrite, matildite, native bismuth, scheelite; (6) marcasite and secondary pyrite, magnetite and hematite. The sequence of deposition of the gangue minerals was: (1) fluorine-bearing minerals-muscovite topaz, apatite, triplite, fluorite-more or less contemporaneous with the cassiterite and wolfram;' (2) quartz-contemporaneous with the earlier sulphides; (3) carbonates--contemporaneous with the later sulphides. The stages overlapped somewhat.The composition of the sphalerite and heat treatment experiments with the solid solutions indicate that the blende-group sulphides were deposited at about 6000 C., and cooled rapidly, so that unmixing of the solid solutions was arrested. This accords with the likelihood that the country rock temperature was not above 2000 C. Annealing experiments at between 3500 C. and 6000 C. led to further precipitation from solid solution at the lower temperatures, and to significant segregation by solid diffusion within, a week, indicating that both deposition and cooling of the ore were rapid processes-completed in a matter of days. Since the mineralizing solutions must have lost some heat during...

Jan 1, 1957

By C Johnstone

Project management is not a task to be undertaken lightly. Mining projects generally present even more challenges due to ChinaÆs remoteness and complexity. Having experiences in project management in the West is certainly an asset, but China can present the uninitiated with any number of headaches. To undertake a project there can have many problems that are unique to China. For the last 15 years, China has seen an increasing number of foreign capital investment projects in the mining industry. Practices involved in mining project development have experienced/are experiencing an evolution. Since 1996, Sino Gold Mining Ltd has delivered three mines in China, ie Jianchaling Gold Mine, Jinfeng Gold Mine and White Mountain Gold Mine. Through the work, Sino Gold has established a solid knowledge base and a capable and skilful workforce in effectively undertaking mining projects in China. This paper is concerned with the experiences accumulated so far by Sino Gold in project management in China. An overall review is conducted regarding the reform of the mining project development in China. Opportunities and challenges are highlighted within the political, economic and culture context. Brief summaries of the development of the three gold mines are presented.

Jan 1, 2009

By Harald Ludwig

In 2002, excavation support work commenced on the Capitol Visitor Center project located adjacent to the nation?s Capitol building in Washington, D.C. The outlying work (Slurry Wall Work at Main Site is not discussed) consisted of providing excavation support for a new truck tunnel approximately 1900 feet long up to 50 feet deep as well as support for the new underground auditorium and Library of Congress tunnel. The excavation support consisted of a combination of conventional drilled in soldier beams, lagging, tiebacks and braces; intricate underpinning inside the existing Capitol building; support of an existing Russell Tunnel; soil nailing and tiebacks underneath the existing Russell Tunnel; two temporary bridges; and a deep soil mixed wall with lateral support provided by braces. As part of an on-going research program, some of these braces were instrumented with strain gauges. The deep soil mixed wall was approximately 300 feet long and 65 feet deep on either side of the truck tunnel. Approximately 34,000 sf of deep soil mixed wall, 90,000 sf of conventional excavation support, 200 braces, and 320 tiebacks were installed. This paper describes the large scope and breadth of the project that required a variety of excavation support techniques. A few of the challenges in designing and installing the support of excavation are discussed. This paper also presents the results of the instrumentation program conducted on the deep soil mixed wall, which stood open for more than a year.

Jan 1, 2006

By Desiree Willis

Disc cutters have determined excavation rates of rock tunneling projects for more than 50 years. First developed in 1956 by James S. Robbins, disc cutters (then 279 mm or 11 in. in diameter) were used to bore limestone of 190 MPa (27,500 psi) unconfined compressive strength (UCS) and were loaded with 7.12 t (15,700 lbs) each. Modern cutters have reached up to 508 mm (20 in.) in diameter and are typically loaded with up to 31.7 t (70,000 lb) to economically bore through the hardest of rock up to plus 400 MPa (60,000 psi) UCS. New developments, such as larger cutter diameters, are geared to increasing the bearing capacity and wear life of the cutting structure. This, in turn, increases cutter life, cutter load and cutter penetration. Disc cutters have also been re-designed on a small scale for use in hard-rock utility installations. Additional variables also affect the three factors, including cutter spacing on the cutterhead, cutterhead diameter and cutter materials.

Jan 1, 2007

By Tracy Brettmann

In recent years the Augered Cast-In-Place (ACIP) Pile industry has seen a substantial increase in the quality control options available to Contractors, Engineers, and Owners. Quality control methods range from the simple, manual techniques that have been used for years to new computerized installation monitoring equipment and nondestructive testing methods. Our ability to monitor and test ACIP piles has grown to such a degree that the industry is struggling to determine how much quality control is enough. This paper reviews the many options available and describes the pros and cons of each. The various nondestructive testing methods, in particular, have been difficult to apply reliably due to misapplications of methods and misinterpretation of the results. ACIP piles have unique properties that require the various nondestructive testing methods available be considered very carefully in determining the method most appropriate for a particular use. Some nondestructive testing methods, as well as automated monitoring equipment, potentially can be applied effectively to increase the level of quality control for ACIP piles. The experience gained on real projects using these new methods, in conjunction with the old procedures, provides valuable information for future applications.

Jan 1, 2000

By Jan E. Nesset, Colin Hardie, Peter Radziszewski, Donald P. Leroux

"The successful introduction of new high intensity stirred milling technologies (e.g. IsaMill, SMDetritor) to the mining industry in recent years prompted Noranda-Falconbridge to initiate a study comparing these technologies to the conventional technologies of ball milling and existing vertical stirred mills (e.g. VertiMill). The study was unique in that it utilized the same material (Brunswick Mine zinc cleaner regrind mill feed), the same sizing instrument (a Malvern laser difractometer) and sampling protocol, and media size and type (for the high intensity stirred mills). The paper compares the net energy efficiency (kWh/t) of the various technologies, their power intensity (kW/m3) and product size distribution spread (P80/P20). A key finding is that media size is critical to achieving optimal performance. As part of the performance comparison, an analysis of the four methods of power measurement was made (Prony brake, shaft torque, grinding chamber reaction torque, “no-load” correction) and followed-up with an experimental test procedure using three of these methods. The findings include divergent results for power measurements and some explanations based on the observations are proposed. The direct shaft torque and Prony brake calibration methods are shown to be the methods most suitable for stirred mills.INTRODUCTIONThe motivation for the investigation reported here was the lack of a suitable comparison within the available literature of relative grinding efficiency for the emerging crop of new industrial fine grinding technologies. Such comparisons are potentially fraught with inconsistency, from ore samples and grinding media used, to testing methodology, to size measurement techniques, to the power measurements themselves. The collaboration of the industrial suppliers (at the time MIM Technologies and Svedala, now Xstrada Technologies and Metso Minerals) and McGill University (P. Radsiszewski) were sought in order to ensure as valid a comparison as possible. The work was performed between October 2000 and November 2002, led by the mineral processing group at the Noranda Technology Centre (NTC) in Pointe-Claire, Quebec. The paper is presented in two sections; Part A considers the different power measurement methods and a comparison of the results for the SMDetritor (SMD) technology, while Part B reviews the grinding performance of the 5 technologies investigated using the selected performance criteria."

Jan 1, 2006

By R. M. Becker

THIS IS a progress report on a study of the application of statistical practice to mine and mineral sampling undertaken by the Federal Bureau of Mines to provide sound theoretical and practical data for use of the mineral engineering professions. One of the problems in mine sampling is determining the reliability of the results. For certain types of sampling data (random data) the reliability of the results can be stated mathematically. For other types of data there is no known means of quantitatively expressing reliability. In applying measures of reliability to a set of random data, some knowledge or assumption of the characteristics of the particular data is necessary. In many fields these characteristics are well known. However, in mining, where the data are in assays, these characteristics are not well known.

Jan 1, 1961

By P. I. James, M. R. Baker

Este artículo analiza la nueva producción de cobre a partir de "minerales de desecho" de baja ley usando la tecnología de Blue Planet Strategies DEMET™ (Dynamic Electrode Mining Effluent Treatment, por sus siglas en inglés), que tiene como objetivo salvar la brecha de procesamiento entre la solución débil de lixiviación en operaciones de extracción por solventes/electrowinning (SX/EW), removiendo electroquímicamente los metales a partir de corrientes débiles y a la vez generando productos concentrados en metales objetivo en un análogo funcional de extracción por solventes (SX). Se estudió el tratamiento de la débil solución de lixiviación pregnant (PLS por sus siglas en inglés) y se usó para estimar los impactos económicos y de producción para una hipotética lixiviación en pilas de cobre brownfield y una operación aumentada DEMET usando SX/EW para tratar el "mineral de desecho." Se presenta la remoción de cobre a un 86% de eficiencia en las placas por debajo de 0,1 g/L de cobre con un consumo de energía de 0.55 kWh/lb de cobre y una concentración del producto mayor a 10 g Cu/L. El modelamiento arrojó aproximadamente $2/ lb para la producción total de cobre y costos de tratamiento menores o iguales a $1/lb con un inmediato aumento del margen bruto de operación del 12% para el brownfield incrementado. Se indicó también un aumento de la vida de la mina con un margen bruto promedio de 38% en la producción aumentada de "mineral de desecho" con valores de cobre de $3.25/lb.

Jan 1, 2014

[Executive J. V. W. REYNDERS, Chairman WILLIAM H. BASSETT E. DEGOLYER I-I. C. BELLINGER RICHARD PETERS, JR. Finance GEORGE OTIS SMITH, Chairman H. A. GUESS F. JULIUS FOHS Admissions GEORGE D. BARRON, Chairman DAVID LEVINGER P. A. MOSMAN H. K. MASTERS J. A, SINGMASTER Alternates F. G. BREYER C. W. HAMILTON F. E. PIERCE]

Jan 1, 1928

Interest in industrial minerals in recent years has increased to such an extent that it has taken them into the mainstream of the Australian mineral industry. Notwithstanding that time series data on the values of production, exports, and imports show that industrial minerals are overshadowed by metals and energy minerals, their contribution to the national economy is important and more significant than would seem to be indicated by the statistics. Whereas the ex mine value of metals generally includes some processing (at least to a concentrate stage), most industrial minerals are valued at little more than their extraction cost, in addition to which such costs are generally low because most industrial minerals are exploited in low-cost surface operations. Consequently, values of mine production of metals and industrial minerals are not strictly comparable in that values of mine production of metals tend to be overstated Short term growth of the industrial minerals sector is assured because of several new projects already commissioned but not yet reflected in the statistics. Longer term growth is also assured, based on various other major projects that are likely to come on stream in the early to mid 1990s.

Jan 1, 1989

Terramin Australia LimitedÆs Angas Lead and Zinc Mine operates in the unique and picturesque environment of Adelaide Hills, 60 km South East of the Adelaide city centre itself. The mine was granted approval for construction by the South Australian Government in April 2007 and the Process Plant was constructed and commissioned in July 2008. This paper outlines the background to the plant design and the approval process given the close proximity to the local town of Strathalbyn, with a major focus on the commissioning learnings from the Concentrator startup for future reference and a review of the operational performance of the Concentrator throughout the first year of successful production versus design and expectations.

Jan 1, 2009

By Jerry T. Shelby

Surface and underground mining operations require equipment with high power output ratings. Haul trucks, loaders, dozers, and other equipment need increasing horse-power to meet production demands. To get more horsepower out of the engines driving the equipment, most manufacturers use turbocharging. Detroit Diesel puts the number at about 90% turbocharged, while Caterpillar estimates 75% to 80% of all its equipment is turbocharged. Turbocharging increases the power output and overall engine efficiency. But it presents some maintenance and operational problems that were not factors when only naturally aspirated engines (nonturbocharged) dominated the scene. A turbocharger is an exhaust-driven air compressor. Using the waste energy in the engine exhaust, a turbine wheel is driven. This wheel is connected by a common shaft to a compressor wheel. The shaft is supported by two plain bearings, or bushings. As the turbine wheel is rotated, the compressor wheel continually compresses the intake air to the cylinders. Compressing the intake air means that more air can be put into the cylinder to burn more fuel. The more fuel the engine can completely burn or combust, the more horsepower the engine can produce. Even though the turbocharger is a relatively simple device, it is a sensitive engine component. It requires special consideration at engine start-up and shutdown. Being freewheeling and exhaust driven, turbochargers can experience temperatures of 540°C 1000°F) and rotational speeds of more than 100,000 rpm. Due to those temperatures and speeds, lubrication is critical to the operation and life of a turbocharger. The turbo is located high on the engine, with the oil supply running through an external line from the sump. The recommended practice is to start the engine and allow it to idle for a few minutes before any revving or loading. This allows the oil to reach the turbo and properly lubricate the bearings before high rotational speeds are seen. Turbo oil supply lines can be as long as 1.5 m (5 ft). Depending on ambient temperatures and oil viscosity, it can take as long as 30 seconds for oil to reach the spinning turbo. However, as little as five seconds without oil can damage the turbo's bearings, reducing its life and overall efficiency. Lubrication problems seen at shut-down can also significantly affect turbo life and efficiency. Manufacturers recommend an idling period of five to seven minutes before engine shutdown. This allows the turbo to slow down and cool off somewhat to help prevent oil coking and bearing damage. When the engine stops, so does the oil supply. There is very little oil left on the bearing surfaces and in the turbo oil supply passages. The immediate heat transfer from the turbine wheel to shaft, bearings, and turbo body literally cooks what is left. This high heat without oil flow can cause bearing deformation by actually melting some of the bearing material. The rapid oil oxidation and coking will restrict oil passages, damage bearings and shaft. Besides heat soaking, there is another problem. If the turbo is spinning at high speeds when the engine is shutdown, the turbo must spin-down to a stop without oil flow. With the large size of turbos used on mining equipment, this spindown time without oil can be for as long as 10 to 20 seconds. Fortunately, lack of lubrication at start-up and shutdown and the subsequent bearing damage can be prevented by oil injection devices. These devices hold a reservoir of engine oil. The oil is injected to the turbocharger bearings immediately on start-up and for several minutes after shutdown. Oil injection devices are spring loaded, hydraulic accumulators. They are actuated at start-up by a solenoid wired to the starter motor. Engine oil pressure charges the accumulator during normal operation. Upon shut-down and loss of oil pressure, the device provides oil to the turbo for about two or three minutes. With an oil injection device, the engine can be started and immediately driven without fear of turbo damage. Also, an abrupt shutdown will not damage the turbocharger since the device will continue to lubricate for two or three minutes. A word of caution. Be sure the oil injection device provides positive oil displacement (pressurized oil flow). Do not use a gravity-flow device. Unless it is a true accumulator, the device could starve the turbo for oil on start-up, Ask for start-up and shut-down pressures and delivery times before considering installation. Keep the oil clean, and follow the manufacturer's recommended oil change intervals. These intervals are usually shorter than with naturally aspirated engines. Use oil with a CD rating designed for diesel applications. A multiviscosity oil is preferable. Use a synthetic engine oil, such as Mobil's Delvac 1, Gulf's Super Duty II, or Chevron's Sub-zero Fluid. Synthetics have much better flow properties at low temperatures. They also have greater oxidation stability (they can take the high heat of turbo-bearing lubrication. And they produce fewer deposits because they are more thermally stable. But synthetic oils do cost more - two or three times more. One additional point - maintain the air intake system. Since all mining is usually in a dusty environment, air filters should be changed regularly and intake systems should be checked for leaks. All intake air passes through the turbo. Any dirt or abrasives entering the turbo will damage the unit and shorten its life. While mining is a heavy duty business with severe operating conditions, you can get the life from your turbocharger that you expect by following a few simple steps: • equip the turbo with an oil-injection device to provide lubrication on start-up and shutdown; • change the oil and filters regularly; and • use the proper oil-synthetic, if possible.

Jan 3, 1987

By Albert L. Toenges

[The i~ ortance o~ S3~e, fdequnt, nQ economical tr~n~po~t~t on 8ys~em Th~a bee~ e~~~~siz8d by the introduction of mechanical loading in co 1 mines, pa.rticula:c y \'r~ e::-e ~o?oile loaciine; ~ac~ine!;j rrre u .... ed. This papar i tr_e . eco:1d or' ?. ~eries deGcribi 1{) t:;'~~11>ort:ltion G stems et1-p oyed in mech3JlizeG. f!lincs. Progre,-s ?. epo~ t J...2.t deal t ~~tirel.: ,'Ii th the l:se of rail .laulagr £or c;atl:erine tran~ortc;tion, ailc, in t-!is paper 'Ii 11 be i acuss d c .icilY rub"col'-t? ro ~ t:tto::"ing as Ie _ as ani:naJ., con-",reyor, an ot.he~ systems of rnil gatheri?1.g. ~ho l)urpo~e of this invosti-gation is, as outlined in Progress ,~ort 1, to studT . Q analyz0 v rious systems nov.: in. u"'e El.I1d to derivQ cor..cl :cicn .... tllcrcfrom.]

Jan 1, 1941

By Chen Xia, G. Deschenes, Wan-Tai Yen

"Ammonium thiosulphate is a potential replacement for the cyanide in gold leaching. However, the high reagent consumption hinders its practical applications. In order to reduce the thiosulphate consumption, chemical additives were used. The gold leaching tests were conducted on a sulphide copper-bearing gold ore with 0.3M thiosulphate, 0.03M copper sulphate and 3M ammonium hydroxide solution at 44% solids and pH 10.2. Sulphate, sulphite, amino acid and chelating agents were initially used as additives. It was found that chelating agents (EDTA and NTA) could reduce the thiosulphate consumption from 30 kg/t to 17.8 kg/t with some increase of gold extraction. The improvement from other additives was not significant. Other approaches were also attempted to reduce thiosulphate consumption with some success. The thiosulphate consumption could be reduced to about 17 kg/t by reducing copper sulphate concentration fiom 0.03M to 0.0015M; adding 0.04M of EDTA; replacing copper sulphate with 0.001M of nickel sulphate. The increase of pulp density fkom 44% to 60% solids could reduce the thiosulphate consumption to 17 kg/t as well. Limiting the dissolved oxygen content by sparging nitrogen reduced the thiosulphate consumption further to 10 kg/t. It could be concluded that the regulations of copper and oxygen supply in the lixiviant were the keys to reduce the reagent consumption.INTRODUCTIONCyanidation, as the predominant gold leaching method, has been used in mining industry for more than a century. The low reagent requirement and the high performance are the reasons for its great success. However, cyanidation cannot deal with ores containing large amount of copper, nickel, arsenic and zinc minerals. This type of ore may consume more reagents and result in a poor gold extraction. On the other hand, the carbonaceous materials may preg-rob the gold from pregnant solution and make cyanidation a problem leaching method. Further more, the high toxicity of cyanide represents another challenge to modern gold mines. In the beginning of the year 2000, an environmental disaster caused by an accidental spill in Yugoslavia was broadcasted world-widely (Gurevitch 2000). Gold mine operators are facing higher social pressures and increasing costs on environmental protections. The usage of cyanide in mining industry has been banned in some countries and locations such as Czech Republic, Japan, Turkey, California, Colorado, Wisconsin and Montana States. Thus, a non-cyanide lixiviant is required."

Jan 1, 2002

By S. J. Schatzel, W. P. Diamond

High methane emissions originating from the active face areas and from the fractured formations overlying and underlying the mined coalbed can adversely affect both safety and productivity in underground coal mines. Since ventilation alone may not be sufficient to control the methane levels in the longwall mining environment, gob gas ventholes have become a standard supplementary methane control option in many mines. As mines progress into deeper and gassier coalbeds, or as longwall panel size increases, ventilation and gob gas ventholes together may not be sufficient to maintain methane levels within statutory limits. To decrease the risk associated with methane emissions under these circumstances, in-seam horizontal methane drainage is often used to reduce the gas content of the coalbed prior to mining. Horizontal methane drainage borehole completion designs, drilling strategies, and degasification lead times may need to be adjusted for site-specific conditions due to mine design, geology, and the gas content of the coalbed. This study investigates different horizontal methane drainage borehole patterns, borehole lengths, and degasification times prior to and during panel extraction to evaluate their effectiveness in reducing methane emissions using a "dynamic" 3D reservoir modeling of a 38 1-m wide longwall panel operating in the Pittsburgh coalbed. Results of this study showed that dual and tri-lateral boreholes are more effective in decreasing emissions and in shielding the entries compared to fewer shorter, cross-panel, horizontal boreholes parallel to the longwall face. Modeling results showed that after 12 months of pre-mining methane drainage, the average longwall face emission rates can be reduced by as much as 10.3 m3/min and 6.8 m3/min using tri- and dual-lateral boreholes, respectively. It was also shown that if pre-mining methane drainage time is short, it is important to continue methane drainage during the panel extraction to maximize reductions in longwall face emissions since additional face emission reductions achieved during this period can be comparable to pre-mining degasification.

By Robert B. Fulton

Summary of data and estimates for 52 fluorspar properties in the following 13 foreign countries: Mexico Thailand China (PRC) Morocco Tunisia Italy Spain South Africa France United Kingdom Kenya Namibia Federal Republic of Germany Data includes deposit type, resource tonnage and grades, mining and beneficiation methods, annual production, fluorspar products and by-products, manpower requirements, capital and operating cost estimates. For operating properties, engineering and cost data have been developed for present and anticipated levels of production. Hypothetical operations have been assumed for undeveloped deposits.

Jan 1, 1984

By James Goldberg, Mark Withey

The Material Service Thornton quarry is a multi-million annual production tons complex. Surrounded by busy surface highways, and divided by a railroad on the north/south axis and further divided by a major interstate highway on the east/west axis, blasting is a daily challenge. This paper deals with the problems of production blasting in an area adjacent to that interstate highway, and paralleling a busy four-lane highway. Discussion includes primary blasting issues such as borehole size, drill patterns and flyrock controls. Discussion also includes blast designs, timing schematics, smooth-wall blasting solutions, traffic and vibration concerns and many other factors influencing the success of this project.

Jan 1, 2006

Minerals are vital to any industrialized civilization. Annually, the United States uses more than 4 billion tons of new mineral materials, or about 40,000 pounds per person-about half being mineral fuels and the other half being metals and nonmetallics. Stable and economic domestic mining, mineral, metal, and mineral reclamation industries are essential to the economy. The value of United States energy and processed materials of mineral origin exceeds $200 billion annually. Although a number of minerals are imported, especially some designated as "strategic and critical," most U.S. mineral supplies are derived from the domestic mines and processing facilities that you will be seeing, reading about, and visiting as you use this visitor guide. We hope you enjoy your experiences. This pamphlet, a guide to mining and mineral operations that may be observed or visited and some other points of interest relating to minerals, is intended to aid tourists and students who are interested in mining. Some may wish to study our Nation's romantic past; others may plan to enter the minerals industry as a career; still others may have a primary interest in conservation practices. The pamphlet is also intended to aid State and local officials, Chambers of Commerce, and mining firms in answering some of the many questions of tourists and students.

Jan 1, 1976

By J. L. Wiley

THIS REVIEW contains abstracts of the technical literature and patents dealing with the history, development, and commercial application of the Bergius and related processes for the hydrogenation, under greater than atmospheric pressures, of liquid and solid carbonaceous materials such as coal, lignite, their distillation and extraction products, pitches and tars, and petroleum and its distillation residues. An attempt has been made to include abstracts of all the published information on this process and of as much of the captured foreign documents and reports compiled therefrom as could consistently be reviewed during the time allotted for the work. Contact with the current literature and patents and review of the foreign documents will be continued and the information will appear in Synthetic Liquid Fuels Abstracts, which is being issued bimonthly as a Bureau of Mines publication. The material in this review is divided in two sections-literature (part I) and patents (part II)-and each of these is arranged alphabetically by author or patentee with further chronological arrangement under each author or group of authors. Secondary authors and patentees as well as assignees are cross-indexed to the main entry. In serial articles or reports the complete series appears in the alphabetical arrangement according to the author of the first member of the series. Succeeding members as well as secondary authors are entered as cross references; Titles of the journals are used as the authors in anonymous references. By following such a procedure, an author index is not required. However, a detailed subject index and a numerical patent list by countries are given as part III.

Jan 1, 1950

The mining industry has recognised for some time the importance of supporting programs which serve to educate the Australian public about the socio-economic benefits of mineral resource development. More recently, industry leaders have realised that the future development of the industry will depend on attracting sufficient young people to commit to a career in the industry. Apart from lending support to the traditional education institutions in Australia, the industry now has the opportunity to participate in the development of education programs in museums. Whilst historic, mining-related theme parks such as Sovereign Hill and Coal Creek in Victoria serve very effectively the objective of relating past mining activities to the socio-economic development of Australia, there still exists the need to provide a facility which, under the same roof, excites interest in geology, mining, mineral processing and the role of minerals and energy in modern society. The redeveloped Geological and Mining Museum (the "Mining Museum"), which is located in The Rocks area of Sydney, meets this objective. With the central themes of formation and transformation this new Museum, which aims to be the best of its type in the world, will use modern museum exhibit techniques and the resources of the Minerals and Energy Information Centre to educate the community including teachers and school children. In the best tradition of museums, outstanding mineral and other collections will complement a comprehensive range of interactive, high technology exhibits which will include a number of exploratory "hands on" facilities. Australian companies are joining with Government to fund this exciting new museum. There is still a need for industry professionals to realise that a modern "mining" museum is no longer just a repository for objects of mining heritage but is also an important centre which serves as an important educational and public relations interface. The Education Section of the new "Mining Museum", which is linked closely with the new Minerals and Energy Information Centre, will be working closely with appropriate mining-related Tertiary institutions to develop specific career programs aimed at secondary students who wish to pursue a career in the mineral resource industries.

Jan 1, 1989