Search Documents

By G. Norman Owen, Roger E. Scholl

INTRODUCTION The analysis and design of underground structures to resist vibratory motion due to earthquakes has been of interest to engineers for several decades. The dynamic stability of a powerhouse cavern was considered in the 1960s (Campbell and Dodd, 1967). About the same time, the designers of the San Francisco Bay Area Rapid Transit system developed procedures for analyzing the subaqueous tunnels placed under San Francisco Bay and the tunnels excavated along the land portions of the alignment (Kuesel, 1969). Japanese designers developed fairly sophisticated procedures for analyzing subaqueous tunnels during the late 1960s and early 1970s (Kuribayashi et al., 1974). In the past decade, proposals to site important critical underground facilities in regions with moderate to high seismic activity have increased the interest in earthquake engineering of underground structures. Seismic designs or seismic studies have been conducted for rock caverns for storage of petroleum or location of power plants (Yamahara et al., 1977; Glass, 1976), buried tanks for fuels or rad¬ioactive waste (Fukushima et al., 1977; URS/Blume, 1976), tunnels for disposal of nuclear waste (Yanev and Owen, 1978; Wahi et al., 1980), and urban mass transit tunnels (Monsees and Merrit, 1984). One of the greatest drivers of the interest in seismic analysis and design of underground structures has been the proposals to dispose of high-level nuclear waste in mined repositories some 300 to 600 m (approximately 1,000 to 2,000 ft) below the ground surface. In 1979, the authors, in conjunction with Professor Tor Brekke, presented a paper on an evaluation and design procedure used in a study of a proposed nuclear waste repository (Owen, Scholl, and Brekke, 1979).

Jan 1, 1985

It is not uncommon to find large quantities of combustible materials in underground metal and non-metal mines. Support timber is the predominant combustible material. Spontaneous combustion, welding and cutting, shorted or overloaded electrical cables and careless smoking are common ignition sources. More recently, there is increased use of diesel mobile equipment that requires fuel storage and transfer areas. Diesel fuel spillage on hot engine manifolds and motors can result in rapid flame growth and heavy smoke accumulation in a matter of seconds. In-expensive, reliable fire detection and suppression systems are available to provide early warning of fire conditions and to isolate and extinguish fires that originate in fuel storage and transfer areas. This report presents an example of how technology developed and demonstrated under Bureau of Mines Contract H0242016, Mine Shaft Fire and Smoke Protection System, may be applied to protect underground diesel fuel storage and transfer areas. The area application described in this report is a representative example only; the fire protection described includes the concepts of ? Early warning and alarm ? Isolation ? Extinguishment ? Control

Jan 1, 2011

By M. G. Maruma

The effect of the amount of cold reduction and annealing temperature on the evolution of the texture of AISI 441 steel is reported. The steel was cold rolled by 62%, 78%, and 82%, followed by isothermal annealing of each sample at 900°C, 950°C, and 1025°C for 3 minutes. The crystallographic texture was determined by Phillips X?Pert PROMPD texture diffractrometer. Microstructures were characterized using optical microscopy and scanning electron microscopy (SEM).The results show that sample that received 78% cold reduction and annealing at 1025°C presented the highest Rm-value and lowest ?R-value, which would enhance its deep-drawing capability. In addition, this sample showed the highest intensity of shifted ?-fibre, notably {554}<225> and {334}<483>. It can therefore be concluded that the ?-fibre, which favours deep drawing, is optimal after 78% cold reduction and annealing at 1025°C.

Jan 1, 2013

By D. F. Malan

In deep level hard rock mining the rheological behaviour of the rock is important as time-dependent aseismic processes can lead to a stable dissipation of energy thus reducing violent outbursts. Underground closure measurements, observations of time-dependent fracture formation and siesmic data indicate that the rock in deep South African gold mines shows significant time-dependent behaviour. The objective of this work is to quantify the time-dependent rock behaviour for laboratory specimens and underground conditions. Laboratory experiments indicated that lava and quartzite specimens undergo measurable creep strain at stress magnitudes below the failure stress. Quartzite is however prone to more significant creep at lower stress levels. A viscoelastic analysis showed that laboratory creep results can not fully explain the behaviour observed underground. The in situ behaviour is governed mainly by the rheological behaviour of the fracture zone and the resulting time-dependent formation of new fractures. A viscoplastic discontinuity model implemented in a boundary element program is used to simulate this behaviour.

Jan 1, 1997

By Peter B. Dowden, Robert A. Robinson

Boulders, frequently found in tunnels excavated through soils, can pose major problems for full face TBMs in terms of slowing or halting the tunnel advance, cutter damage, and abrasive wear. The paper aims to consider the problem as a whole, from the geological characteristics of boulder sites, to the appropriate physical design of theTBM, and its operation in boulder-laden soils. In addition, visualization of boulders and other subsurface obstructions by seismic methods and ground penetrating radar are reviewed. The paper will assist the construction planner in assessing the risks and preparing appropriate specifications.

Jan 1, 2001

The roasting of sulphide ores and concentrates is often the first step in the production of metals or chemicals. In many processes, the production of sulphuric acid is viewed as a by-product, while in some plants production is an important economic factor. Regardless of the purpose, a pyrite roasting plant consists of mainly three plant sections: roasting, gas cleaning and sulphuric acid. With the addition of air, the pyrite concentrates are transformed into solid oxides and gaseous sulphur dioxide at temperatures of 600 - 1000° C. After cleaning and cooling, the sulphur dioxide in the roasting gas is further processed to sulphuric acid. Two types of reactors are used depending on the application: stationary or circulating fluid bed . For over 60 years, Outotec has progressively been developing the principle of fluidised bed technology in several different reactor types for a multitude of process applications. The versatility of the fluidised bed reactor system has manifested itself in the treatment of minerals, including solid fuels, and for metallurgical processes both in the ferrous and non-ferrous fields. Process applications have included roasting, calcining, combustion and charring of coals, as well as off-gas treatment. This paper provides a summary of the pyrite roasting technology currently used along with a simple cost comparison of pyrite roasting and sulphur burning processes.

Jan 1, 2009

By Ed Beswick

Resource Update Drilling Program ? Pre-feasibility ? Exploration Metallurgy Program ? Grindability ? Metallurgical Optimization ? Hydrometallurgical Options Preliminary Mine Development Design Environmental Permitting Infrastructure Development

May 1, 2008

By Steni Stefani, Sanjay Dave

"This paper describes an innovative method, used for the first time in India, for the construction of a 1.0metre-thick positive plastic concrete cut-off wall (CoW) at the upstream toe of the dam at the Kishanganga Hydro-Electric Project in Jammu & Kashmir- India. The extremely difficult bouldery geology with an overburden laden with very hard Panjal Volcanics (quartz, feldspar, muscovite and chlorite minerals) boulders of up to 0.8m to 1.8 metres in size with UCS of up to 265 MPa and the requirement of socketing the CoW into the underlying hard bedrock (UCS 265 MPa) for 1.50m made the choice for the excavation methodology critically difficult. After having evaluated several other existing methods – including hydromill trenchers – the Civil Contractor Hindustan Construction Company, in agreement with its Foundations Engineering Consultant (Ricerca e Sviluppo – Cantieri e Gestioni) opted for a two-stage construction method: firstly, preliminary full-depth drilling and “surgical” blasting with full-length inclinometer checking of borehole verticality to ensure the exact location of rock fracturing and fragmentation coincided with the required position and that it was vertical, notwithstanding efficient trenching into the bedrock of a nominal 1m by 1.5m section; and, secondly, excavation by using heavy duty mechanical rope grabs made locally and developed by the Consultant in collaboration with the Contractor. The details of the methodology and the salient construction data is presented and commented for the 33-metre deep CoW installed at a working platform elevation of 2364.50 m above sea level in a very remote area.BACKGROUNDThe Kishanganga Hydro Electric Project (KGHEP) is a ROR (run-of-the-river) project is located on the Kishanganga River some 140kms North-West of Srinagar, capital of Jammu & Kashmir State of India, for generating 330MW of power in a 90% dependable annual year. The key components of the project are: Concrete Face Rockfill Dam (CFRD), Chute Spillway, Plastic Concrete Cut-off Wall (CoW), Head Race Tunnel (HRT), Surge Shaft (SS), Inclined Pressure Shaft (PS), underground Power House and Transformer Hall, Tail Race Tunnel (TRT).The Power House Site is accessible throughout the year from Srinagar while the remote Dam Site, with its tortuous road climbing the Rajdan Pass at 3556m (11,667 ft) above sea level and several 20-tonne capacity Bailey bridges removed prior to snowfall, remains inaccessible for around 4 months between mid-November to mid-May due to winter and heavy snowfall - the only access is by helicopter, weather permitting. Temperature at the Dam Site drops down to minus 27degrees Celsius during winter, therefore, careful planning from the beginning was most essential for the successful delivery of the Project.This paper deals with the Cut-Off Wall construction which was performed, for the first time in India, adopting a “Drilling and Surgical Blasting” method. However, this technology is not new and diaphragm wall excavation with the aid of drilling and blasting has already been done in some of the projects globally; namely:"

Jan 1, 2017

MR. W. E. WAINWRIGHT occupied the chair, and in introducing the lecturer said, on account of the absence of the vice-president, it fell to his lot to introduce the lecturer. Mr. Tennberg, he said, was visiting Australia, and those present might wonder who he was.He understood that the lecturer w~s a reputable practising geophysicist, associated with a reputable company! It was rather desirable perhaps to say that the Institute had made some inquiries with regard to his status. Geophysics was a comparatively newscience, and had suffered several hard knocks in Australia and elsewhere. Most of those knocks had been the result of undue optimism of a number of people who did not understand what they were talking about. It had been claimed that geophysics was a...

Jan 1, 1930

Copper waste dump leaching is growing in importance because of the.large tonnages (up to 250,000 ton/day) of low grade waste rock available from open cut mining of copper deposits and proof that controlled leaching of copper from such dumps can be profitable.Overburden or waste rock, ranging in size from large boulders to fines, is dumped as cheaply as possible on sloping sites. Copper is leached from the dumps by applying up to 12,000 gal/min of leach solution (a combination of spent solution from cementation and make-up water) to the top of the dumps by various techniques.Efliuent from the dumps is sent to a cementation plant for copper recovery.Factors which may be controlled, either directly or indirectly, to give a controlled copper content in the dump efliuent (usually 1-2 g/l.) are the cycle of operations (i.e. the alternate wetting and drying periods), thevolume of solution applied to the dump, pH, Fe2+ and Fe3+ content or redox potential, oxygen content, bacteria and their necessary nutrients, and temperature.Dissolution of oxide copper minerals appears to be mainly a function of acid concentration. Copper sulphide minerals need oxidation for dissolution to occur and this is accomplished by a combination of oxygen,ferric ion, and bacteria. Oxidation of pyrite, oxidation of Fe2+ to Fe3 +, and hydrolysis of Fe3+ are of some importance in leaching practice. The presence of gangue carbonate minerals is detrimental.Physical factors connected with penetration of solution into large rocks are important and the treatment of an individual dump usually extends over a period of many years. Recovery of copper from solution is usually achieved by cementation with iron (usually in the form of crumpled cans) but the use of sponge iron is becoming more important. Iron consumption varies from 1 to 4 lbiron per pound of copper. Preconcentration of the copper in the efliuent solution by solvent extraction followed by electrolysis may become a useful method.Application of dump leaching techniques to metals other than copper depends on finding an economic method of recovering the metal from solution...

Jan 1, 1967

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a roomand-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90%. But, the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing oversprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99% and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber.

By Jeffrey R. Hill

To extend the life of the Merchants Railroad Bridge crossing the Mississippi River in St. Louis, MO, the owner implemented a rehabilitation and reconstruction project. The Merchants Bridge provides a key link in the transcontinental railroad system. The bridge is of local importance to the Terminal Railroad Association ? providing a link between St Louis and a rail switching yard in Venice, IL. The intent of the bridge rehabilitation is to keep the Merchants Bridge in service, even though the bridge was originally constructed in the 1890?s. The project involved replacing the East and West approach deck truss spans with new deck girder spans. The rehabilitation program required construction of new concrete piers to support the new spans. In order to reduce the track down time to two, ten day single track shutdowns, the specifications required that all foundation and substructure work be completed while leaving the existing spans in place. The preliminary bridge design specified rock-socketed drilled shaft foundations. Drilled shafts proved to be challenging due to working from beneath the existing bridge, a high water table, utilities, a flood wall, and existing rail way lines. The micropile alternative was technically appropriate given the access limitations, shortened the foundation rehabilitation schedule by several weeks, and realized a significant cost savings to the Owner.

Jan 1, 2006

A substantial proportion of current and historic West Coast gold production comes from deposits situated around the margins of æice ageÆ glaciers. Gold has been eroded and transported by glacial ice then deposited in till and outwash gravel. The interplay between fluvial and glacial processes, climate, basement geology, tectonic uplift, sediment supply and sea level dictates many aspects of the development of the West Coast landscape. The way in which the external forcing factors interact is crucial in determining the gold content of placer deposits in this region. The following is an outline of some of the factors that influence the gold distribution in vicinity of glacial margins.

Jan 1, 2000

By John R. Hoskins

The Bureau of Mines conducted an investigation to more exactly define the influence of some end conditions on the laboratory-determined uniaxial compressive strength of rock samples. Limestone, marble, sandstone, and granite were used to provide a range of specimen modulus of elasticity from 2.7 X 106 psi to 10 x 106 psi. Four variables were studied: Nonparallelism and surface texture of specimen ends were the specimen variables investigated; the end platen size and the adjustable or spherical head friction were the machine variables studied. It was concluded that the loading ends of small laboratory models and samples should be prepared with surface irregularities that do not vary from a plane surface by more than 0.001 inch. It was also concluded that nonparallelism of the specimen ends should not exceed 8 minutes for a rigid head load or 15 minutes for an adjusting head load. The measured compressive strength of specimens prepared with these tolerances will be statistically the same with any diameter or thickness of platen and any degree of head friction if initial alinement of the specimen is assured.

Jan 1, 1968

By Arthur H. Redfield

The expansion of city street laving which characterized the ten years ended December 31, 1929, according to a survey of 201 representative cities, made by the bureau of Mines, reached it climax in 1927, with decreases reported for 1928 and 1929. The upward trend, followed by a decline, was general in cities of all sizes included in this study, but was most pronounced in cities of 40,000 to 100,600 inhabitant and in the Northeastern, Southeastern, and Southwestern States. In the North-Central States the trend of paving; was downward from 1925 to 1929; in the Pacific, and Rocky Mountain States it was generally upward. Over the nation as a whole, bituminous types of paving continued to lead, furnishing two-thirds of the total street pavement laid in the 201 cities from 1925 to 1929. The actual yardage of bituminous pavement laid in these cities, however, was 3.8 per cent less in 1923-than in 1925, and the ratio of bituminous pavement to the total pavement t dropped from 70.4 per cent in 1925 to 62.1 per cent in 1928, rising to 65.1 per cent in 1929. The area paved with Portland-cement concrete amounted to only one-fourth of the total, pavement laid in these cities from 1925. to 1923., but the yardage of Portland-cement pavement increased by half during the period, and its share in the total pavement grew from 19.3 per cent in 1925 to 30.0 per cent in 1928, declining to 29.5 per cent in 1929. Brick, block, and stone pavements, which constituted the remaining one-twelfth of the total pavement laid in the 201 cities, decreased one-third in yardage, and declined in relative importance from 10.3 per cent in 1925 to 6.6 per cent in 1929.

Jan 1, 1931

By F. E. du Plessis

"The distinction between data suitable for process control and data subject to aliasing only becomes quantifiable with the availability of rapid real-time measurements. Expecting the dynamics of flotation to vary for different ore types, process flows and equipment types; a study was conducted to compare the dynamics of different flotation processes. The results shed light on the critical sampling intervals required for process control which in turn allows process stabilization and optimization. The technology used for the in-line measurements is based on diffuse reflective spectroscopy and has been introduced into the mineral processing industry over the past ten years. It has been widely implemented in the sulphide flotation industry in South Africa for the real-time measurement of grade.BACKGROUND AND OBJECTIVE A study was conducted by Du Plessis and Keet (2010) to quantify the minimum sample frequency required for grade and/or impurity control. The study was based on chromite data collected at 15 second intervals from the concentrate line of a flash float cell in the Platinum industry. The data captured the natural process variation of the entrained chromite through water recovery due to changes in feed parameters and flotation performance. It was found that the minimum rate of sampling required from the studied flash float concentrate was 2 minutes. This sampling interval time accounted for 90% of the variance in the process data. It was further found that a sampling interval time of longer than 4 minutes produced data with no significant correlation to reality. The dynamics of the flotation process has been misjudged in the past but can be quantified with the availability of real-time grade measurement based on diffuse reflective spectroscopy. The objective of the study was to compare the dynamics of different sulphide flotation processes through the comparison of maximum sampling interval times required to combat aliasing. All data were collected from single stream analyzers that are currently installed at mineral concentrators. The technology used is based on diffuse reflective spectroscopy."

Jan 1, 2012

By Sanjiv Dhanjal

"Often mineralogy dictates the physical properties of a material rather than chemistry. This in turn affects how that material behaves in a process plant, and whether optimum conditions for refining one mineral are different to those for refining another. For example how does refining copper from chalcopyrite differ to refining copper from bornite?Minerals are naturally occurring inorganic solids that have a definite chemical composition and an ordered atomic (crystalline) structure. X-ray diffraction is a common and highly developed method to identify and quantify minerals. X-rays are fired onto a material and the mineral is identified by the angles where the diffracted X-rays are in phase.Most X-ray analyzers are laboratory based. A sample is prepared and analyzed by a detector that travels in an arc to collect the diffraction pattern. COSMA has a curved detector which picks up the complete x-ray pattern instantaneously. Therefore, material is collected and transported through the machine where is it is analyzed continuously.COSMA measures about 0.5 tons of material per day, while laboratory analyzers measure a few grams at a time. Real time data trends are produced allowing for improved process evaluation and automatic control. The COSMA on-line system has taken X-ray diffraction out of the laboratory into the field.There are a number of systems in operation in cement production. It is recognized that on-line mineral analysis has a role in many other processes. This paper presents the technology and invites further discussion should the technology be beneficial to members of the audience.INTRODUCTIONThis article describes COSMA, a system that provides direct and continuous on-line mineral analysis using X-ray diffraction in the field. While X-ray diffraction is a common technique used in mineral analysis, the time from sampling to analysis can be hours and plant operators typically do not get the data in time to control a process or respond to an upset. COSMA provides rapid measurement, analysis and feedback of data, in real time. This provides powerful information that can be used to optimize operation, thereby reducing costs and increasing quality."

Jan 1, 2009

Many mines in Canada, the US and S. Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due the excessive weight. It has been suggested (DeLorme, 2000), that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm(1 ¾ in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg(10 ton) skip may exceed the safety factor of the rope. To improve on the current understanding of the mechanical behavior of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modeling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca 1995b) is used to simulate the structural behavior of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modeling on the wire rope will be discussed.

May 1, 2002

By R. Frim, S. D. Ukeles

The present U.S. production of bromine is from inland brines located in Arkansas and Michigan. The most concentrated domestic brines (up to 5,000 ppm bromide)are situated in Arkansas. Less concentrated brines(about 2,500 ppm bromide) are located in Michigan. The amount of bromine sold or used in the United States came from three companies operating in those two states. Its value was $191 million. In 2004, the estimated U.S. bromine production was 222 kt (244,000 st). That compared with 216 kt (238,000st) produced in 2003.

Jan 1, 2005

By J. -F. Lessard

Most underground mines rely on ore pass systems to ensure the transport of ore and waste. The design and operation of ore pass systems often rely on past experience, which is often anecdotal and at times contradictory in nature. This paper summarizes the current practice in Quebec underground metaliferous mines. The information was collected during a series of site visits in ten underground mines. The database includes information on ore pass configuration, support, materials transited, and overall ore pass performance.

Jan 1, 2006