Search Documents

By L. J. Vincze

The program of study of pellet binder materials was begun by the ORF in 1963 to examine various Canadian materials as substitutes for bentonite which is imported in large tonnages (199,270 tons in 1969) from the U.S.A. for Canadian pellet plant operations. Most of the raw bentonite used in Canada originates in Wyoming, North Dakota and more recently Greece, resulting in relatively high transportation costs to pellet producers. Some Canadian bentonites available in Western Canada (Alberta) can be beneficiated for uses as pellet binders but could not compete in cost with U.S. sources due to the cost of beneficiation and the higher rail transport charges to Eastern Canada. It is difficult to find a substitute for bentonite, and many materials have been investigated by research groups but, so far, no economic substitute is in use. However, some success is apparent in studies of low cost materials such as clays, sea weed, peat moss and low grade coal, The work done by the ORF over several years has covered systematic test¬ing of Ontario clays, lignite, some types of tree bark, waste sulphite liquors of various kinds, and peat moss as binders for iron ore pellets. The major effort has been concentrated on peat moss and has included a study of the influence of different additives. Since analysis of peat moss for humic acid is difficult and time consuming, a certain amount of time was devoted to development of improved methods, the most useful of which was a spectrophotometric method based on extraction of peat by sodium pyrophosphate for determination of humic substances. In the present paper, only the most recent work concerning the use of peat moss with suitable additives is discussed in detail, since it is the most conclusive and best documented portion of the program.

Jan 1, 1971

By Beverly W. Dunning

The effect of vacuum melting on the elimination of gases and nonmetallic inclusions for six low-alloy steels was investigated. The purpose of these studies was the analysis and comparison of differences in gas content and inclusions in air-melted and vacuum-melted steel. Data obtained from melts of 1-1/4 to 20 pounds indicate that vacuum melting decreases the number and size of nonmetallic inclusions and at the same time increases the degree of dispersion of the remaining inclusions. These improvements are undoubtedly related to the elimination of approximately 80 percent of the nitrogen and 90 percent of the oxygen as well as most of the undesirable metallic trace impurities.

Jan 1, 1961

By Sanchita Chakravarty, Sumantra Bhattacharya, Divya Jyoti, A. K. Mukherjee, Soni Jaiswal

"Release analysis is independent of collector and frother dosage and type, but it is primarily influenced by the degree of liberation or “state of release of the sample”. The shape of release curve is an indication of the degree of liberation. This paper briefs about the effect of reagent combination, particle size and surface characteristics on the release analysis of difficult-to-clean LVC coal.Release analysis of three LVC coal fines obtained from two different coalfields of India was carried out at three different size levels such as -0.5mm, (-0.5+0.1) mm, and -0.1mm. The collectors used were n-dodecane and commercial diesel oil. Incomplete liberation of coal fines even at a size of -100µm, corroborated by photomicrographs of ROM and clean coal macerals, in a great measure reduced the flotation-based cleaning potential of the fines. FESEM images of fines reveals that the adherence of ultrafine onto the surface of relatively coarser particles reduced the clean coal recovery. The results obtained also appear to be coal, reagent combination and, particle size and particle surface specific. Only one coal indicated the liberation as is usually expected for -0.1mm particles with a reasonable yield of 65% at 18% ash. INTRODUCTION Froth flotation has a long history of being used to treat coal fines. Coal flotation is considered to be difficult, if the percentage of Near Gravity Material (NGM), i.e. essentially locked particles, in flotation feed is >10% [Aplan, 1993], which is usually the case with all the coking coal fines in India. The fines are rich in vitrinite, so valuable for coking coal. Unfortunately, there appears to be no standard procedures to determine the separation efficiency of froth floatation. Release analysis proposed by C.C. Dell in 1953 [Dell, 1953], aimed to determine the ultimate floatability of coal. Several other techniques had been proposed but release analysis technique has been considered to be a vast improvement over the batch flotation process [Forrest et al. 1994]."

Jan 1, 2018

By G. L. Neumann

"INTRODUCTION Mining in this area is inactive. The entire region is now comprised of small farms. Because approximately 1,500,000 tons of magnetite ore had been shipped from this area between 1855 and 1915, it was deemed probable that geophysical surveying and core drilling might indicate other ore bodies or sizable extensions of the previously mined ore bodies.ACKNOWLEDGEMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has, as its primary objective, the most effective utilization of our mineral resources, thus fortifying our national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiatien tests.The chemical analyses and beneficiation tests included in this report were performed at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., under the general supervision of J. B. Zadra, chief, College Park Division, Metallurgical Branch, and the immediate direction of Dr. Alton Gabriel, head of the laboratory service unit.The Mineral exploration Was under the general supervision successively of G. D. Jermain, district engineer, C. B. White, district engineer, and McHenry Mosier, chief, College Park Division, Mining Branch.The geophysical section of the exploration was performed by G. B. Botsford, engineer of the Bureau of Mines. Assistance was given by the Division of Geophysical Exploration of the Bureau of Mines, Dr. F. W. Leo, chief."

Dec 1, 1947

By Nasser Madani, SULTAN ABULKHAIR

The abstract of the paper discusses the challenge of quantifying iron content in a coal deposit in Kazakhstan. The iron dataset is limited, coming from only three drill holes and some stope samples, while a large amount of geological information is available from legacy drill hole data. The paper proposes a workflow using multiple-point geostatistics to model geological domains and two-point geostatistics to model iron content within these domains. The results show that the direct sampling (DeeSse) algorithm effectively reproduces the complex seam layers, and sequential Gaussian simulation models the iron within each domain.

Mar 30, 2022

By B. K. Shibler

As a part of the Bureau of Mines' intensive; 'investigation of domestic manganese deposits, ore-dressing studies were conducted on three samples of oxide and silicate manganese ores from various Wyoming properties. The samples wore as follows: 1. A 2-ton sample of ore was obtained by a Bureau engineer during examination of the Caulkins-McGuckin property in the center of Crook County, 10 miles north of Sundance, Wyo. The ore body was described as a vein deposit in rhyolite porphyry. 2. The J. B. C. Mining Co. submitted a 1-ton sample of oxide manganese ore from a property located 44 miles northeast of Rock River in Albany County, Wyoming. 3. A 1-ton sample of oxide-silicate-ore was obtained by a Bureau examining engineer from the Gheen property in the northeast corner of Washakie County, Wyo. The ore body was described as a replacement deposit in a country rock of silicified limestone. As the samples differed widely in physical and chemical characteristics and also in their response to methods of concentration, ore from each property was considered a separate ore-dressing problem.

Jan 1, 1949

By I. Nishkov, I. Grigorova, N. Valkanov, M. Ranchev

The processing of sulphide ores with variable and complex mineral composition and physical properties, such as those processed by two-stage selective flotation scheme in “Erma reka” concentrator, Minstroy Holding JSC, requires excellent selectivity in order to achieve acceptable concentrate grades. The lead-zinc ores from the hydrothermal lead-zinc deposits mainly contain galena (PbS), sphalerite (ZnS), pyrite (FeS) and chalcopyrite (CuFeS2), as well as non-metal minerals such as quartz, carbonates and clinopyroxenes skarns. One of the main impurities present in sphalerite is iron, which is known to be detrimental to the rate of sphalerite flotation and its recovery. The results from the conducted laboratory and industrial tests, presented in the previous study, showed that it is possible to depress the iron rich sphalerite by adding MINFIT® (modified sulfur-oxy depressant) at the pH of approximately 9.5 in rougher lead flotation circuit, leading to reduction of zinc sulphate consumption and complete elimination of cyanides from the flotation process. Furthermore, the consumption of copper sulphate, which reactivates the surface of the zinc minerals, was significantly reduced. Consequently, the optimisation of the reagent regime in the Erma reka concentrator, led to notably improved qualitative (grade, recovery) properties of the final lead and zinc concentrates. Moreover, when comparing the reagents consumption for 2014 and 2016 – when the processing plant have been applying the new optimized reagents regime, comprises the use of MINFIT as the primary depressant, the following results have been achieved: ZnSO4 decreased by 30%; CuSO4 consumption decreased four times and full rejection of cyanides from the process. Finally, this paper provides a state-of-the-art review of the obtained results during the period of application of the new flotation reagents regime in the Erma reka concentrator, Minstroy Holding JSC.

Jan 1, 2018

By Peter Zhang, Daniel Su

Following the first longwall excavation at a deep-cover gas well site, the pre-mining modeling prediction of longwallinduced casing deformations in the fully cemented production casing were in excellent agreement with post-mining Caliper survey results. However, after second panel mining, the post-mining Caliper survey revealed a large plastic deformation near the top of the Pittsburgh Seam. The focus of this paper is to identify the possible cause of such an anomalous deformation. Very high longwall-induced casing stress near a thick claystone layer at 23 feet above the Pittsburgh seam horizon was identified as the primary cause. Leaving the production casing uncemented or using softer cementing material between intermediate and production casings is identified as the best practice.

Feb 1, 2024

By John E. Kelley

Laboratory equipment, which simulates abrasive impacts between steel and minerals that might be present during pneumatic transport of coal, was used by the Bureau of Mines to characterize the potential explosion hazard of such collisions in an atmosphere of fine coal dust, air, and methane. A variety of coal mine rock materials, including sandstone, limestone, and pyrite-bearing limestone, were impacted with specimens of pipeline steel. Tests were con-ducted in atmospheres containing zero to 6.4 vol-pct methane mixed with zero to 300 mg/l coal dust. Coal dust in air alone was not ignited by abrasive impacts, but additions of as little as 1 vol-pct methane to the coal dust and air mixture resulted in ignitions. Steel impacting against sandstone caused ignitions in mixtures of coal dust, air, and methane, and the probability for ignitions increased with an increase in methane. No ignitions occurred with impacts of steel on lime-stone or pyrite-bearing limestone, even when large showers of sparks were produced. Studies of the effect of tangential collision velocity showed that no ignitions of coal dust, air, and methane occurred below 900 fpm (4.57 m/sec). Ignitions in coal-air-methane mixtures were found to be caused by a hot friction-induced smear on the impacted rock at the impact site rather than by sparks. High-speed photography was used to verify this observation.

Jan 1, 1976

By Juan J. Monsalve, Nino Ripepi, Richard Bishop, Jon Baggett

"Terrestrial laser scanning (TLS) is a useful technology for rock mass characterization. A laser scanner produces a massive point cloud of a scanned area, such as an exposed rock surface in an underground tunnel, with millimeter precision. The density of the point cloud depends on several parameters from both the TLS operational conditions and the specifications of the project, such as the resolution and the quality of the laser scan, the section of the tunnel, the distance between scanning stations, and the purpose of the scans. One purpose of the scan can be to characterize the rock mass and statistically analyze the discontinuities that compose it for further discontinuous modeling. In these instances, additional data processing and a detailed analysis should be performed on the point cloud to extract the parameters to define a discrete fracture network (DFN) for each discontinuity set. I-Site Studio is a point cloud processing software that allows users to edit and process laser scans. This software contains a set of geotechnical analysis tools that assist engineers during the structural mapping process, allowing for greater and more representative data regarding the structural information of the rock mass, which may be used for generating DFNs. This paper presents the procedures used during a laser scan for characterizing discontinuities in an underground limestone mine and the results of the scan as applied to the generation of DFNs for further discontinuous modeling.INTRODUCTIONAccording to the Mine Health and Safety Administration (MSHA), between 2006 and 2016, the underground stone mining industry had the highest fatality rate in 4 out of 10 years, compared to any other kind of mining (MSHA, 2016). Additionally, during that same time, 40% of the fatalities were due to ground control issues, such as roof and rib collapses and pillar bursts. The National Institute for Occupational Safety and Health (NIOSH) developed guidelines for designing underground stone mines (Esterhuizen, Dolinar, Ellenberger, and Prosser, 2011). However, these guidelines do not apply to all underground stone mines.Monsalve, Baggett, Bishop, and Ripepi (2018) present a case study of an underground limestone mine experiencing a structurally controlled mode of failure. The authors analyze different methods to study that type of instability. They conclude that the integration of terrestrial laser scanning (TLS) with discrete element modelling (DEM) can be used to prevent rock falls in underground excavations to enhance worker safety. However, an adequate rock mass characterization and structural mapping must be performed in order to generate reliable models that allow the engineer to have a better understanding of the rock mass behavior."

Jan 1, 2018

By Satyajit A. Vaidya

This paper presents a case-study in the design and construction of deep foundation element supported mats for two residential towers on an18,000-square-foot site in Brooklyn, New York. Based on site sub-surface conditions, conventional mat foundations bearing on medium dense sand, having an allowable bearing capacity of 3 tsf, were originally anticipated for the 16 and 25-story towers. However, when the tower shear walls were relocated to the edges of the mat foundations due to architectural revisions, the significantly increased mat edge contact stresses applied to the soil subgrade resulted in calculated settlements of a magnitude that would adversely impact the proposed structures and the neighboring/bordering lot-line building and rail transit subway structures. To address this issue, deep foundation element supported mats were designed for the towers. The design was performed as an iterative process involving structural SAFE and geotechnical Plaxis finite element computer analysis to develop a coordinated geo-structural model of the foundation system. Initial presumptive design values of 45 pci and 445 kips/inch were used for the modulus of subgrade reaction and minimum deep foundation element stiffness, respectively. The designed foundation system consisted of 40 and 60-inch-thick mat foundations for the 16 and 25 story towers, respectively. Initially, the deep foundation elements were designed as 50-foot-long, 14-inch-diameter elements installed to sustain a maximum individual compressive load of 250 tons. The final deep foundation element design was subsequently refined to consist of a 48-foot-long, drilled and grouted IBO Titan 103/51 element designed to sustain a maximum load of 167 tons. Subsequent field load tests on the deep foundation elements confirmed element stiffness ranging from 1,040 to 1,530 kips/inch, with measured mobilized side shear of about 29 psi. The mat foundation reinforcement was adjusted for the pile stiffness values determined in the field load tests, and the deep foundation supported mats were constructed. The two towers were subsequently constructed, and have performed successfully.

Jan 1, 2010

By Marcos Paulo Kohler Caldas

A recuperação de metais presentes em equipamentos eletroeletrônicos tem atraído interesse em virtude de novas e diferentes tecnologias que visam a reutilização desses elementos químicos em novos processos produtivos. A recuperação de metais das placas de circuito impresso tem atraído o interesse das empresas, pois, ao mesmo tempo que produz bons resultados do ponto de vista econômico, também se pratica o desenvolvimento sustentável, reduzindo a extração de metais da natureza. Este trabalho tem como objetivo caracterizar as placas de circuito impressos (PCI’s) de memória de computadores, através de imagens de microscopia eletrônica de varredura com espectroscopia por dispersão de energia (MEV/EDS), a fim de verificar a presença de metais, visando a sua recuperação.

Aug 17, 2017

By The Staff

THE property of McKenzie Red Lake Gold Mines, Limited, consists of eleven claims located on McKenzie island in Red lake. The mine is about 4,Y:l miles by water from the Howey townsite on the same lake, and about 95 miles north of Kenora, Ont. (see Figure 4). Mail and express are flown-in daily, winter and summer, from Sioux Lookout, Hudson, Kenora, and Winnipeg. All heavy supplies are freighted-in during the summer over a water route, using four marine railway portages, from Hudson, Ont., a distance of about 180 miles. During the winter, freighting over the same route is clone by tractor if necessary, but costs are three to four rimes the summer rate. Due to these conditions, large inventories of supplies must be kept on hand, varying from a spring minimum of $45,000 to a peak of $110,000 early in November. The average cost of all freight brought in from steel during 1937 was $0.01 per pound.

Jan 1, 1938

By L. D. van Dyk, G. S. Tshofu

Iron ore fines are by-products of iron ore mining operations. Unlike iron ore lumps, fines cannot directly be used in conventional iron making processes, and consequently large quantities accumulate around the world. Pelletizing and sintering can be used to convert iron ore fines into agglomerates or briquettes for processing with lump ore, but these techniques are energy intensive and produce greenhouse gases. This research investigated the extraction of iron from iron ore fines using acetylacetone (a ß-diketone) as an environmentally friendly alternative process for fines utilization. A 2k factorial experiment design was used to identify the significant extraction variables. It was found that the reaction temperature and solid to liquid ratio had significant effects on the extraction process. The extraction kinetics were studied at different temperatures and the highest iron extraction (97 %) was obtained after 48 hours at 413 K and 0.025:1 (g:mL) solid to liquid ratio for a particle size range of +106 to -150 µm. The extraction products were easily separated from the unreacted acetylacetone by flash distillation and iron(III) acetylacetonate crystals were recovered. An economic evaluation showed that selling the crystals was profitable. Alternatively, the crystals can be reduced with hydrogen to iron particles and acetylacetone (for reuse).

Jan 1, 2015

By M. Le Roux, Q. P. Campbell, N. Hughes

Water plays a significant role in minerals processing; this is especially true in coal preparation where water-based beneficiation is widely accepted and consistently delivering sharp separation efficiencies and high product yields. Although wet processing is favoured, the substantial process water requirement may prove this impractical and unsustainable in some parts of the world. Many coal-rich regions (including South Africa) have experienced severe water shortages. Coupled with the effects of drought, some countries experience freezing winters from which problems related to frozen process water and machinery may arise. Hence coal preparation practices will soon have to adapt, irrespective of the technical and economic feasibility offered by the currently employed water-based methods. As a result, extensive research into the development of dry methods for effectively beneficiating coal has progressed. This review paper intends to provide a collection of the relevant information pertaining to dry coal processing globally, and aid in understanding the applicability, performance, success or failure thereof. The methods available for dry materials preparation, with special regard to those applicable for coal beneficiation, are detailed in terms of principle, applicability, limitations and performance. Dry coal beneficiation has potential to aid the current wet-based methods with some considerations to possible limitations set forth by coal geology, application, product specification, particle size distribution, moisture, efficiency, capacity and cost. These methods may be established in future, especially in the arctic, arid and under-developed regions through new plant installations, expansions and small mines processing. Keywords: Dry coal processing, preparation, cleaning, beneficiation

Jan 1, 2020

By M. Gonçalves Peixoto da Silva, E. Rodrigo Carvalho Souza Siqueira

Mining in narrow veins is commonly applied for precious metals, generally carried out to extract gold in underground mines, due to the ore occurrence on narrow veins, mainly up to 2-meter large. The current work presents the implementation of the methodology in a zinc mine located in the state of Minas Gerais in Brazil. The Vazante Mine through the years has always carried out mining on stopes with a thickness larger than 3,5 meters, but nowadays due to the need to reduce the waste planned in its blocks, as well as increase the useful life of mine, mining has been implemented in blocks that are less than two meters. Given this, the challenge is to be able to carry out blasts that does not exceed the operational dilution required and does not generate an impact on recovery, as working with extremely heterogeneous stopes. This study seeks to correlate the main characteristics of stopes and its relationship with the results obtained in the execution of those blasts. Also, it proposes an analysis between the empirical data, and existing theoretical references, creating ideal mining parameters, such as minimum thickness, maximum height, and optimum timing in the blast plan. One of the main challenges for carrying out this mining method is the control of operational dilution, generally pointed out as the biggest difficulty for companies that adopt this methodology, due to the thickness of those stopes, any displacement can make it unfeasible, thus the technical level on carrying out the drilling and loading of these blocks must be impeccable, an understanding of the structural geology of the site is also essential for dilution control. The outcome will be a set of ideal parameters and mining methodology to guarantee the success in execution of these blocks, thus bringing a financial benefit to the company.

Jan 21, 2025

By B. D. Nash

The Bureau of Mines continued its research into the recovery of fluorine by the phosphoric acid acidulation defluorination of phosphate rock concentrates. A small process development unit with a capacity of about 10 kilo-grams of charge per hour was operated, and concentrates from both Idaho and Florida were processed. Over 80 percent of the fluorine was evolved and recovered as a dilute fluosilicic acid solution. Phosphate extraction from the concentrates always exceeded 98 percent. The fluorine was converted to a synthetic fluorspar product (3CaFa?SiOa) suitable for use as a slag conditioner in electric furnace steelmaking operations.

Jan 1, 1977

By Mingxia Liu, Hao Li, Qi Liu

"Laboratory batch flotation tests were carried out on fine (-20 µm) hematite to investigate the non-polar oil’s influences when sodium oleate, octyl hydroxamic acid, or oleyl hydroxamic acid were used as a collector. Batch flotation tests were performed with artificial mixed minerals (hematite:quartz = 1:1) under natural pH condition and kerosene was utilized as the model oil. The experimental results showed that kerosene emulsion behaved differently when used in conjunction with the three collectors. Kerosene helped improve the flotation when sodium oleate or oleyl hydroxamic acid was used as a collector. Nevertheless, it reduced concentrate weight yield, grade and recovery to a noticeable extent when octyl hydroxamic acid was used as a collector, especially at low dosages. In addition, single hematite batch flotation kinetics tests coupled with water recovery measurement were carried out to study the role of kerosene at different collector dosages. It was observed that water drainage and the resulting froth destabilization by kerosene was dominant at low collector dosages, especially in the flotation using octyl hydroxamic acid. At higher collector dosages, the water drainage and froth destabilization effect by kerosene was possibly counter-balanced by the higher hematite hydrophobicity and bubble surface tension gradient, which led to more stable froth layer.INTRODUCTION The minerals industry is facing a steady decline in ore grade, compounded by increasing complexity of mineral dissemination. As a result, the ore has to be ground sufficiently fine to have a suitable degree of mineral liberation, which produces large percentages of fine and ultrafine particles outside of optimal size range for ore dressing. Due to the unique characteristics of fine particles, i.e., small mass, high specific surface area, and problems such as increased solubility of complex minerals (Finkelstein, 1997; Finkelstein & Allison, 1976; Fornasiero & Ralston, 2005), high reagent consumption, fast surface oxidation in the case of sulfides (Collins & Read, 1971; Klassen & Mokrousov, 1963), severe particle entrainment (Subrahmanyam & Forssberg, 1988; Warren, 1984), low flotation rates (Glembotsky, 1953; Philippoff, 1952; Ye & Miller, 1988), slime coating (T. K. Mitchell et al., 2005; Parsonage, 1984), etc., flotation performance of these finely ground ores is very poor in terms of low concentrate grade and recovery."

Jan 1, 2017

By B. Fagerberg

Crushing and grinding practice in Sweden follows largely the international pattern. Certain special circumstances, however, have had an influence on the development. Most mines are worked underground in either quite small or in very large units. To utilize small sulphide ores, custom milling is rather common. Apart from the cement industry, the rock species treated are hard and abrasive. Another important factor is the increasingly strict requirements placed on the mechanical condition of different products, especially lump ores and coarse iron ore concentrates. A significant feature in the design and development of Swedish crushing and grinding practice has also been close cooperation between machinery manufacturers and the users. An account of these conditions and an outline of the crushing and grinding techniques employed in Sweden are presented in this paper with emphasis on the mining industry. For background purposes it may be mentioned that crude ore production in Sweden last year included 45 mill. tonsx) of iron ore, of which some 20 mill. tons from Kiruna alone, and 4 mill. tons of sulphide ore from 22 other mines, fig. 1. In addition 8 mill. tons of limestone were quarried for cement production and several million tons of stone and sand for roads, aerated concrete, etc.

Jan 1, 1968

By Alfred Bodenlos

El presente texto señala los depósitos de zinc y plomos encontrados en los cateos del flanco noroeste del cerro Huancapetí, perteneciente a la Cordillera Negra. En el flanco noroccidental del cerro Huancapetí, hay varias vetas que han sido exploradas por pequeños cateos, cuyas altitudes van desde 4480 hasta 4670 metros. Para llegar a esas vetas solo hay caminos malos que cruzan la cumbre de la cordillera al sur del área de la mina Huancapetí. De otro lado, en 1947 la única mina en actividad era la de Wilson, alcanzando 10 toneladas de concentrados al mes escogidos a mano, así como la mina San Idelfonso, la Improvisada, Mariscal y los cateos Señor de la Soledad y Fernandiita.

Nov 1, 1957