Search Documents

By Z. Q. He

This paper introduces the structure and working principle of SLon magnetic separator that has excellent performance in iron removal, and summarizes a part of the examples of applications, which applies this machine to remove iron from non-metallic ores, and shows widespread prospect of application of this machine in the purification of non-metallic ores.

Jan 1, 2014

By Lawrence F. Johnsen, Felix Ferrer, Dino Tomasetti, Cassandra A. Wetzel

"A 17 story building was constructed at the Brooklyn Navy Yard on a site with a long history of development. Most recently the site supported a dewatering well and craneway to service two adjacent drydocks. The subsurface conditions generally consist of the following strata and approximate depths: miscellaneous fill and debris to 20 ft., organic soils to 35 ft., liquefiable sand to 45 ft., varved clay to 65 ft., glacial till to 95 ft. and gneiss bedrock.Hollow core bar piles replaced 18 in. diameter caissons on a 1.67:1 basis. The resulting service loads on the hollow bar piles were 600 kips compression, 21 kips lateral, 180 kips tension and 450 inch-kips moment. The top 30 feet of the hollow bar was cased with a 16 in. x 0.375 in. Grade 50 steel pipe. The piles were socketed 6 feet into bedrock. An extensive load testing program confirmed the axial and lateral load capacities. The paper will also discuss some adjustments to the installation procedure based on the load test program.PROJECTThe hollow bar piles were installed to support a 95,000 sf footprint, 17-story office building at the Brooklyn Navy Yard. The Brooklyn Navy Yard was first developed in the late 1700’s to build merchant vessels. The federal government purchased the old docks and adjoining 40 acres in 1801. The site was an active U. S. Naval Shipyard from 1806 to its decommissioning in 1966. At its peak in World War II it employed 70,000 people, 24 hours a day. Since 1966 the property has been converted to private manufacturing and commercial activity.The site is located between Dry Docks 2 and 3. The adjacent drydocks extend 40 to 43 feet below grade. The drydock walls are restrained by tierods extending back to deadman anchors. The site is also underlain by piles that were installed to support rail lines and a craneway. The building footprint also covered an 85 ft. wide, 70 ft. deep dewatering well which had a thick slab. The structural engineer for the project, ARUP, designed the building to span over the dewatering well.SUBSURFACE CONDITIONSIn September 2014, Langan Engineering conducted a geotechnical engineering study for the project. Figure 1 provides a subsurface profile through the long axis of the site. The general soil profile was very erratic but generally consisted of miscellaneous fill and debris to 20 ft., organic soils to 35 ft., liquefiable sand to 45 ft., varved clay to 65 ft., glacial till to 95 ft. and gneiss bedrock. The fill contained numerous obstructions from the over 200 years of site development. The organic soils were mostly very weak and compressible organic silt. The depths and thicknesses of the varved clay, and sand varied"

Jan 1, 2017

By M. C. Malamphy

A general description of the activities and results of bauxite investi-gation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the sixteenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations of the latter holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By George E. Edwards

Pacific Rim markets for export coal already represent a larger market than the total tonnage imported into the European Community countries and they will continue to expand. The largest importers will continue to be in the sector comprising Japan, Korea, Hong Kong and Tai- wan. It is likely that the total Pacific Rim markets will reach 206 m.t.p.a. by 1990 and 290 m.t.p.a. by 2000, with the major growth in steam coal demand. Australia has an efficient coal industry, represents a stable long term source of supply and is favourably situated geographically to continue to be the largest single supply source.

Jan 1, 1982

By Nadia C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U.S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially water-saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, results, and a remediation plan for in situ leaching based on field observations are presented in this report.

Jan 1, 2010

By Yuemin Zhao, Wenxuan Liu, Maoming Fan, Zhanyuan Long

"Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium and phosphorus. These coalassociated elements are significantly enriched in coal combustion byproduct fly ash because the majority of the main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main element oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides and unburned carbon.Chinese coal fly ash usually contains about 5 to 15 percent of unburned carbon, which are generally chars with irregular shapes and wide particle size distribution. In addition to unburned carbon, XRD analysis of four Chinese fly ash samples from Liaoning, Shanxi, Guizhou and Shandong provinces indicates that the fly ash samples are composed of minerals such as quartz (SiO2), mullite (3Al2O3.2SiO2 or 2Al2O3.SiO2), hematite (Fe2O3), maghemite (gamma form of hematite, ?-Fe2O3) and magnetite (Fe3O4). The mullite and quartz particles are usually present as spherical particles because they are formed by melting clays, feldspars, quartz, calcite and other common minerals in coal during coal combustion. The silicate particles have usually entrapped gas to yield hollow spherical particles because their lower melting point facilitates gas entrapment.The iron oxides are usually spherical also. The magnetite (Fe3O4) is derived from pyrite (FeS2), hematite (Fe2O3), siderite (FeCO3) and limonite (2Fe2O3.3H2O) in the coal. Maghemite (?-Fe2O3) is formed by dehydration of the mineral hydrohematite (?-FeO(OH)) and/or oxidation of magnetite (Fe3O4) during coal combustion. Maghemite (?-Fe2O3) and magnetite (Fe3O4) are strongly magnetic, so they are recovered from Chinese coal fly ash and widely used for coal processing in China (Fan et al., 2005, 2000)."

Jan 3, 2018

By Sherwin F. Kelly

GEOPHYSICS may be considered a vice (albeit, I submit, a comparatively harmless one) whose career is aptly described by Pope's lines: Vice is a monster of so frightful mien, As to be hated needs but to be seen; Yet too oft, familiar with her face, We first endure, then pity, then embrace. Although there may be some that have not yet succeeded in emancipating themselves from the first stage of horrified contemplation, geophysicists may be duly thankful that there are mining men and geologists that have arrived at a state of apparently irretrievable damnation.

Jan 1, 1936

By J Hartog, V Beehan, D Beeson

Treating an ore blend from five different deposits at Newgold’s Peak Gold Mine (PGM) has always been a challenge due to the inherent variability between each of the orebodies.Operating the processing plant at PGM with a ‘normal’ level of process control and a good operations and metallurgical team has allowed the processing plant to achieve above the name plate design at 102 t/h and recoveries in the order of 92.8 per cent for gold and 88.4 per cent for copper.With a company value and culture of striving for continuous improvement, PGM implemented the Manta Cube® system, an advanced process control system, for the semi-autogenous grinding (SAG) mill, gold leach circuit and tailings thickener over a 12-month period throughout 2012 and 2013.The overall benefits of implementing the Manta Cube® system has led to an increase in mill throughput of at least two per cent, improved SAG mill liner life, a ten per cent decrease in cyanide consumption and a reduction in flocculant of at least 30 per cent with no detriment to the gold and copper recoveries.The entire project had a payback period of less than two months, and the combined benefits resulted in an overall increase in revenue of at least $5 million per annum. This is quite significant for a processing plant the size of PGM.This paper describes the methodology, overall results and economic benefit of applying the Manta Cube® system on-site at Newgold’s PGM.CITATION:Hartog, J, Beehan, V, Karageorgos, J and Beeson, D, 2014. Optimisation of the Peak Gold Mine’s processing plant through advanced process control, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 335–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Frederic Souche, Andrew R. Klaetsch, Brian Hann, Nick Goodenow

This paper describes support of excavation (SOE) design and construction for three large diameter shafts excavated through glacial soil and controlled blasting in complex sedimentary rock formations. SOE in soil consists of unreinforced secant pile rings designed to resist lateral pressure in circumferential compression, eliminating costly steel core beam reinforcing. Controlled blasting at the shafts, adits, and tunnels in densely populated neighborhoods requires managing risks to the public, buildings, and utilities. Controlled blasting approaches limited adverse impacts to receptors nearby while achieving adequate production and fragmentation. A site-specific observational approach was used to adjust blasting parameters, limiting the impact on local stakeholders while maintaining daily progress and managing overbreak.

Jun 13, 2023

By Takahiro Miki

In order to use metallurgical grade silicon (MG-Si) as a starting material for solar cell, phosphorus has to be removed from silicon because phosphorus is a n-type dopant. On the other hand, silicon, ferrosilicon, and silicomanganese are widely used as deoxidizers in steel refining processes. Since most of the phosphorus introduced during the deoxidation process is brought into final products, it is important -to lower the phosphorus content of these alloys. Hence, thermodynamics of phosphorus in such metals is important for the evaluation of dephosphorization processes. In the present study, thermodynamic properties of phosphorus in molten Si-P alloys at 1723- 1848K and those of Si-Fe-P and Si-Mn-P alloys at 1723K have been determined by equilibrating respective metals in a controlled phosphorus partial pressure. The results are expressed as follows.

Jan 1, 1998

By W. F., Dietrich

THIS paper deals with the- methods of mining the high-grade clays of California. Although the majority of the clay pits in the state are operated on a scale that is small by comparison with most metal mines, this very fact results in a diversity of methods and gives rise to problems of selection of the method best suited to given conditions. Two or three operators in California produce approximately 500 tons per day of a single kind of clay from a single pit. About five varieties of clay are mined on a scale of 200 to 400 tons per day; not over fifteen varieties are mined on a? scale of 50 to 200 tons per day; and more than 50 varieties are mined at a rate of less than 50 tons per day. It is the aim of this paper to delimit, insofar as the data at hand permit, the conditions and scale of operations that favor the selection of each dominant method of mining that is actually being applied at California properties. Details of the occurrence and utilization of the clays of California have been given in a recent bulletin and are not considered here.

Sep 1, 1928

By Tracey Bodnarchuk, Philipp Mirzoev

Sulfate balance control is a common problem for zinc plants. Roast-leach-electrowin plants are mostly concerned with the over-generation of sulfates while for the HudBay direct leach plant both extremes are possible including potential necessity to buy sulfuric acid to replenish a sulfate-depleted circuit, which makes the problem doubly important. Quantitative methods were applied at the HudBay plant to analyze sulfate generation/depletion based on a local sulfur balance and sulfate extraction calculation in the leach circuit, using a Pb-tie method. Main factors were established influencing sulfate generation/depletion, including the critical role of Pb and pyrite. Regression analysis proved to be effective and allowed the quantitative prediction of Pb concentrations necessary to reach the equilibrium for the sulfate balance. This in turn provided a firm basis for a sulfate-control strategy realized through concentrate blend correction, which allowed the plant to fine-tune sulfate generation/depletion effectively reducing economic consequences of excessive/deficient sulfate generation.

Jan 1, 2015

By M. B. Ramachandra Roa

This paper records the results of the earth resistivity surveys made in the Godavari River in connection with the Ramapadasagar project. After describing the topographical and geological features of the area, the results of the investigation at the several sites have been mentioned. Further, a detailed account has been given of the resistivity methods adopted, the apparatus used and the interpretation of the curves. The resistivity measurements carried out over the water course have been specially outlined, and a review of the verification of the electrical indications by drilling in a number of cases, has also been presented. Introduction The Government of Madras has under consideration the Ramapadasagar project which is estimated to cost some Rs.660,-000,000 (about two hundred million dollars). The most essential feature of this project is the construction of a high dam across the Godavari near Polavaram for impounding the waters of this great river of South India, whose maximum discharge is 2 million cu secs in flood time. It is estimated that when the proposed reservoir is constructed, about one million tons of rice could be produced annually under irrigation. To those who have had any acquaintance at all with the recent distressing famine conditions which India has passed through and is still undergoing, the Lounteous effects which this project will bring about to the country in the future, are obvious. In the region of the proposed reservoir, the river flows for several miles through a hilly tract, hemmed in between flanks of hard, solid rock; but the river bed is mostly sandy. A few bore holes put down in this sandy bed touched rock at a depth of 180 to 200 ft. The river bed is about jo ft above the mean sea level (m.s.l.) and the bedrock was found at —125 to —160 ft m.s.l. The crest of the dam is proposed at +162 ft m.s.l. The proposed dam mould therefore be about 120 to 130 ft above the river bed, and the foundations would have to reach down nearly zoo ft below the bed at the deepest part. A number of alternative sites were proposed for investigation, and it became necessary to quickly ascertain the bedrock topography at these sites. Dr. M. S. Krishnan,* who was consulted in the matter, furnished a detailed account of the geological features of the region and suggested a geophysical investigation which the writer carried out from February to April 1944, employing solely the electrical resistivity methods. The total length of the survey lines for the electrical measurements amounted to 62,600 ft and the number of resistivity determinations was about 2500. Altogether nine alignments for the dam were inten-

Jan 1, 1949

By P. J. Arps

Cyanide (CN) is used to recover gold from its ores in many locations worldwide. In spite of the established history of gold mining in Alaska, modern cyanidation methods have been used at only one location, the Ryan Lode Mine at Ester Dome, near Fairbanks. Ore was processed by heap leaching between 1987 and 1989, when permitting issues caused operations to be terminated. Those issues have since been resolved, and plans to reopen the mine are currently being discussed. Plans are also proceeding to develop several other ore deposits in the state, all of which include the use of cyanide for gold recovery [6]. Since tailings and effluent water produced from these mines will require treatment, it is important to develop detoxification methods suitable for the Arctic and sub-Arctic conditions found in Alaska. Several methods exist for removing cyanide from mining wastewater. However, most industrial users prefer chemical treatment systems, and typically use sodium hypochlorite, hydrogen peroxide, or sulfur dioxide/air/copper to oxidize free and complexed cyanides [9]. Biological treatment has been used successfully at two sites in the United States [30,32] and field tested at several others [20,27,28]. In addition, one mine uses "natural processes", which include natural oxidation, photodegradation, and degradation by naturally occurring bacteria [33].

Jan 1, 1994

By Tuomas van der Meer, Jukka Tanninen, Annukka E. Mäkinen, Mika Martikainen, Laura M. Nevatalo

The mining industry consumes huge water volumes and the waste streams typically contain sulfate, which has caused problems to many operations around the world. Discharge of sulfate to fresh waters is being restricted as the sulfate load increases salinity and causes problems when sulfate is reduced to toxic H2S by natural bacteria. To reduce fresh water consumption, internal water recycling had become a necessity in metallurgical processes. However, the recycling causes accumulation of sulfate and other components in water, causing problems to process performance and increases scaling in piping and equipment. Few technically feasible water treatment processes exist in the market that can be applied to decrease sulfate concentration below gypsum saturation level: biological sulfate reduction, membrane separation, ion exchange, evaporation and chemical precipitation. Some of these technologies are effective for treating wastewater, but there is typically a highly concentrated sulfate fraction left requiring still further treatment. Outotec has developed a sulfate removal solution, Outotec Ettringite process, which allows flexible control of residual sulfate concentration, thereby opening doors for increased water recycle within processes and control of the sulfate in discharged waters. In this article the results and benefits of this novel process along with examples of operating costs are presented.

Jan 1, 2014

By A K. Ghosh

"Inrush of water is always an issue, especially for mines located in heavy rainfall areas. Nowadays, mining companies and research institutes have developed many advanced technologies for study and analysis of hydrological processes. In this paper, an advanced method is introduced, which uses the Shuttle Radar Topography Mission Digital Elevation Model (SRTM DEM) data in the Geographical Information System (GIS) platform to simulate the stream distributions around two specific mines: Super Pit and Griffin coalmine in Western Australia. The impact of this approach is important because it reduces the time and economic cost by creating a high spatial resolution hydrological map in the specific areas. The study identifies the flow path of the run-off water, which helps in adopting a suitable water management plan surrounding the case study mines. The results match with the ground reality. Based on the results, the stream structure around Griffin coalmine is more complicated than that of Super Pit. The bifurcation ratio and drainage density are computed to estimate the subsoil permeability characteristics of the two mines. Recommendations have been put forward to prevent and reduce the potential risks of water accumulation around the open pit mines.Citation:Ghosh, A K, 2016. Application of Shuttle Radar Topography Mission Data in Hydrological Analyses of Super Pit and Griffin Coal Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 162–169 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By B. Macdonald

In 1991, roofbolts were introduced as a primary support for inseam retreat longwall entries at CBDC's Phalen Colliery. Increasing mine depth (+550 m) necessitated replacing conventional inseam steel sets in these entries because they were being severely damaged during wall retreat and subsequently causing gate end problems. Roofbolts had been used in the Sydney coalfield between 1949 and 1963 in room and pillar working, however, some concerns arose with using roofbolts as a primary support in long (2.2 - 3.4 km) single entry roadways. In order to alleviate these concerns, a phased approach was adopted whereby conventional steel densities remained along with roofbolts. The roofbolt design was such that the roofbolts would be the primary support and the steel sets would experience little or no loading. A detailed geotechnical monitoring program was developed by both CBDC and the Cape Breton Coal Research Laboratories technical staffs. The results of this monitoring were used to build-up confidence in roofbolts and subsequently reduce the steel set densities until eventually only roofbolts were used as a primary support. This paper will discuss briefly the phased introduction of rootbolts at Phalen Colliery and more specifically the development of geotechnical data collection and interpretation.

Jan 1, 1994

By N. Katsikaros, N. S. ‘ Yap, B. Adaszynski

"Cyanide is a well proven, effective lixiviant that has been utilised for centuries in gold extraction processes. Despite being used in close to 90% of gold processing plants, cyanide leaching is still being scrutinised due to its toxic nature. With governments tightening the regulations on cyanide management, and recently erected sites situated closer to community and environment, leach waste and tailings treatment has become increasingly important. Gekko Systems has worked with engineering companies and directly with gold producers to provide technical services and supply complete modular cyanide destruction (detox) systems for plants leaching both run-of-mine ore and high sulphide gravity and flotation concentrates. Although similar in principle, the different materials presented unique challenges in design and implementation. Similar to designing any section of a processing plant, the development of the cyanide destruction plant design began with laboratory test work to simulate the full scale operation. This paper focusses on the laboratory test work and how other critical factors such as geographical location, logistics, and local community play a role in the process design and construction. Two design and supply cases are discussed in this paper; one treating intensive cyanidation concentrate leach tails and one treating whole ore CIL tails. Although these plants both use the SO2/O2 process, each presented different challenges in laboratory testing and plant design, resulting in variations in final implementation including reagent choice, oxygen supply, and process control.INTRODUCTIONSince 1887, cyanide has played a large part in the beneficiation of gold from gold bearing ores. Cyanide is used to solubilise gold into solution, and is typically added in excess to maintain the leaching process. Some or all the excess cyanide can often be recovered and reused in the process however chemical destruction of cyanide is often necessary to manage cyanide levels in the tailings storage facility (TSF)."

Jan 1, 2016

By N. F. Faria, F. Monteiro, B. O. Taiwo, A. Palangio, D. Fonseca, J. Manuel

This paper explores the interpretation and application of Particle Size Distribution (PSD) curves in optimizing blast design and enhancing downstream operations. The study looks at important factors like D50, D80, fines content, and the uniformity index to show how PSD curves affect the efficiency of different mining processes. The first section of this paper discusses the impact of blast design parameters such as burden, spacing, and explosive energy on the resulting PSD, highlighting their significance for downstream operations like crushing, and material handling. The section concluded that proper alignment of PSD with downstream size classes, like primary crusher inlet sizes, among others, can result in substantial cost reductions and productivity gains. The second part presents a case study from dstgroup aggregate quarry in northern Portugal, utilizing fragmentation analysis to evaluate blast performance and promote continuous improvement. The section specifically examines the effect of stemming material size on blast fragmentation, comparing the impact of using aggregate with a D80 of 12.32 mm versus a D80 of 21.94 mm. The D80 value represents the particle size at which 80% of the stemming material is smaller, making it a critical parameter in evaluating the stemming's effectiveness in confining explosive energy. The drilling and blasting designs were meticulously planned using O-PitDev and O-PitSurface software to ensure accuracy in blast parameters and layout. To assess the fragmentation resulting from these different stemming material sizes, the study utilized WipFrag 4 software. The software allowed for precise measurement of particle size distribution after the blast, as well as a detailed comparison between the two stemming sizes. Results from the analysis indicate that using bigger-sized stemming material led to improved blast confinement, which in turn resulted in better fragmentation compared to the smaller-sized material. The reviewed blast videos demonstrate that the larger aggregate effectively contained the explosive energy within the borehole, thereby reducing premature venting and directing more energy towards breaking the surrounding rock mass. This led to finer fragmentation with D80 = 1240.1 mm, D50 = 685.9, and Dmax = 2580 mm, which is advantageous in downstream operations like crushing and milling. On the other hand, the smaller stemming material (D80 = 21.94 mm) did not confine the explosive energy as efficiently, resulting in coarser fragmentation (D80 = 1327.37 mm, D50 = 750.76, and Dmax = 2370 mm) and reduced overall blast efficiency. These findings highlight the significant influence of stemming material size on blast performance and fragmentation outcomes. 

May 4, 2025

By R Sinclair, D Landwehr, I Hunter

"The Syama Gold Mine, located in southern Mali, was established in 1990 by Broken Hill Propriety Limited (BHP). The operation began treating oxide, and in 1994 it transitioned to processing hard and refractory ore based on ‘whole-of-ore’ roasting. In 1996, BHP was succeeded by Randgold Resources and the operation ran until 2001, when it was placed into care and maintenance.The Syama ore is classified as a double refractory ore with pyrite occluding the fine grained gold present in the ore and high levels of organic carbon presenting a challenge in terms of preg-robbing behaviour. The ore is extremely competent and this combination of metallurgical features was the main source of metallurgical problems encountered by the previous owners.Resolute Mining Limited (RML) acquired the Syama project in 2004. Following a feasibility study and the development of a revised processing flow sheet the plant was recommissioned in 2008 using a combination of old and new equipment. The revised flow sheet enabled primary sulfide ore to be treated by flotation and roasting of the concentrate to produce a calcine suitable for conventional carbon-in-leach (CIL) processing.Commissioning and ramp up of the plant was a troubled process, with monthly gold production being as low as 3000 oz in 2010. Poor availability of equipment and lower-than-forecast recoveries were the primary contributors.During the last five years, RML has utilised a systematic approach to improve production, focusing on mechanical reliability, metallurgical recovery and process bottlenecks. Modifications to the circuit have been as a result of both innovation and the application of technological improvements. Improvements have been made to the flotation, roasting and CIL circuits and RML has introduced a deslime circuit to treat flotation concentrate, in addition to the very successful commissioning of a new 1 Mt/a oxide circuit in December 2014. These changes have resulted in gold production increasing to more than 20 000 oz per month in 2015.This paper presents the processes, change implementation and outcomes of the modifications made to the sulfide circuit to address the availability and recovery problems.Apart from the expansion of an existing, world-class deposit and discovery of new resources, future improvements on the path to a class-leading gold mine include the continued reduction of the unit cash cost, increase in overall sulfide circuit gold recovery, increased throughput through continued innovation and consistency in the plant’s operation.Citation:Sinclair, R, Hunter, I and Landwehr, D, 2016. Syama Gold Mine - the Journey towards a Class-leading Gold Mine, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 213–224 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016