Search Documents

By Damir Dedic, Wörle. Patrick

"Soil properties within a construction project area are analyzed during the planning phase. However, it is only possible to achieve selective soil exploration, even in the case of very extensive investigatory programs, which results in a certain soil risk and uncertainties for planning and execution.Therefore, the application of monitoring systems is becoming increasingly important in the field of geotechnics. The application of suitable monitoring systems for these particular purposes provides considerable knowledge relating to the load bearing behavior of the soil and the ground anchor. Applications that present major challenges to measuring anchor forces include back-anchorages of long-lasting and very deep construction pits, construction pits in urban areas, slope and embankment supports for track and vehicular routes, port and lock structures, and uplift control. Apart from overseeing individual construction stages, monitoring systems analyze the interaction between the soil and structure throughout the latter’s entire life cycle and safeguard the functional capability of the applied system components. Geotechnical construction projects can be adapted, optimized and carried out with enhanced safety from the information obtained.Conventional Monitoring SystemsThere are numerous approaches for determining anchor forces of bar or strand anchors. Lift-off tests and measurements with load cells are the most common methods.Lift-off Test: Lift-off tests provide a possibility to monitor the prevailing force in strand or bar anchors. The entire anchor head structure is lifted using the appropriate equipment. The steel tendon is prolonged, or in the case of strand anchors, a screw-on cap holds the wedge carrier so that a tensioning jack can be mounted above it. Then, the tendon is prestressed until the lower anchor nut (bar) or wedge carrier (strand) is lifted off from the anchor plate. The intersection of the two straight lines in the figure represents the force at which the anchor nut or the wedge carrier lifts off from the anchor plate. Thus, the intersection displays the actual load of the anchor. This form of anchor force control gives conclusive results, but at the same time requires extensive accessories and extra personnel to execute the test. For this test, a sufficient bar overhang must be available, the wedge plate must possess an external thread, or there must be a strand overhang of at least 24 in (60 cm). Furthermore, the anchor head must be freely accessible and in a position to be reached with the necessary equipment."

Jan 1, 2017

By Samuel Polinsky, Lawrence W. Bierman, Wayne Perkins

[A column float beneficiation plant using 9, 8.5 foot diameter, cells was constructed by the Simplot Company and the Smoky Canyon Facility in the fall of 1986 and has been in operation since May of 1987. The float beneficiation process was developed jointly by the Simplot Company and the Bureau of Mines (Salt Lake City, Utah) which incorporates the Bureau's bubble generator design and chemistry system based around the reverse float technology, (Albany Bureau of Mines, Application of Carbonate-Silica Flotation Techniques to Western Phosphate Materials, Rule, Dallenbach , Larsen, RI8728, 1982) . This chemistry has been modified by Simplot in both patented and unpatented improvements. The objective of the beneficiation process was to reducethe A1203 content in the overall pipeline concentrate by 0.2 wt z. Therefore, a process stream was identified in the mill circuit which provided an opportunity to isolate and treat 1100 tons per day of poor quality phosphate concentrates The process allows recovery of approximately 15% of the mill concentrates, otherwise unsuitable for fertilizer production. The alternative would have been to waste this ore. Wasting would have resulted in considerable ore loss, increased mining costs and required additional products grinding. ]

Jan 1, 1989

By B. Panton, J. Carvalho, E. T. Brown

"A major consideration in the design of high capacity tiedown anchors for dam, bridge and tower foundations is the tensile resistance of the rock mass to pullout, typically as a result of overturning moments or hydrostatic uplift. Rock mass pullout capacity for installed anchors is developed from the tensile strength and fracture propagation properties of intact rock, the orientation and physical properties of the discontinuities and anchor confinement at depth. The typically assumed, but generally conservative, design approach is to calculate anchor pullout capacity using the dead weight of a uniformly shaped inverted “cone” with an assumed initiation point and breakout angle. In some cases, some tensile or shear strength is considered across the area of the assumed pullout cone, however, these strength estimates are based primarily on based on limited historic testing data, empirical relationships for rock mass strength developed for other applications, and engineering judgement.As an alternative to the current foundation anchor design method, this paper presents a new approach to the rock cone pullout problem using Discrete Fracture Networks (DFN) combined with numerical simulations. The simulations presented in the paper investigate the influence of fractures in a synthetic rock mass on ultimate anchor strength. In addition, the global influence on fracture network statistics on rock mass pullout failure is also discussed and it is contended that some of the aleatory and epistemic uncertainty inherent in the design of rock anchors can be reduced by considering fracture statistics in anchor design."

Jan 1, 2015

By Jr. Smith

Borates have been mined in the desert areas of California and Nevada for more than 100 years. To about 1890, playa surface mining provided the chief sources of boron minerals. Underground mining of colemanite and later of borax and kernite was predominate until about twenty years ago. Open pit mining of the large deposits of borax and kernite near Boron, California has been most significant for the past twenty years. Mining of colemanite in the Ryan, California area, near Death Valley, began in 1907. Following the discovery of the large deposits in the Boron area (about 1957), mining in the Death Valley area became nearly nonexistent. Only small tonnages were mined for special uses. Little mining was done in the Boraxo area near Ryan. The first claim was made in about 1915 In 1960 the area became the property of the Kern County Land Company, which was acquired by Tenneco Oil Company in 1967. In 1976 the various borate properties and claims in this region were acquired by American Borate Corporation. The open pit mine is now approximately 400 feet (121.9 m) deep, 3000 feet (914.4 m) long and 1000 feet (304.8 m) wide. The borates in the Boraxo pit consist primarily of three minerals. These are about 50% coiemanite (C2B6O11' 5H2O), about 40% probertite (NaCaB5O9.5H2O), and 10% ulexite (NaCaBcO9.8H2O). The colemanite, along with boric acid and high-grade coiemanite ore from Turkey provide the only sodium-free borates for production of textile grade fiberglas. When heated to its decomposition temperature, colemanite decrepitates to a fine powder. This provides the basis for the concentration process. The gangue minerals in this deposit are primarily calcite and clays, including bentonite. The ore body has a very low arsenic content.which is a desirable feature. Test work had been done with samples prior to the results discussed herein. This paper will discuss results of test work which were the basis for erection of a plant, and the subsequent plant operations.

Jan 1, 1978

By Jason Herron, Joseph Brown

The common couplings for joining sections of helical piles with an outside diameter of 6.625 inches and 8.625 inches are square on square, flange to flange, external pipe sleeve, internal pipe sleeve, and welded joint. Each coupling type has advantages and disadvantages in efficiency, capacity, installation, and economics of the installed pile. All these coupling types have been used in the helical pile market in North America for various applications and designs. Many of these applications require on-site testing, but test records are not typically shared with the helical pile industry. Due to the lack of information available for square on square and flange to flange couplings, testing was done to compare the efficiency of installation, load to deflection response, and torque to capacity ratios of external pipe sleeve, square on square, and flange to flange couplings. Field installations and tension tests were performed in non-cohesive (sand type) soil near Caseyville, IL and in cohesive (clay type) soil in Centralia, MO. The data collected during these tests included rotations per foot during installation, installation torque, applied pressure, and deflection. The results of this testing are analyzed and discussed within this paper. The results indicate that the square to square coupling is the most efficient of the designs tested, but this conclusion cannot be fully justified without further testing due to the variability in the data gathered and the small number of piles tested. INTRODUCTION A helical pile is typically assumed to be a medium-displacement pile when its outside diameter is between 4.5 inches and 8 inches and a high-displacement pile when its outside diameter is greater than 8 inches. A helical pile designer has multiple options when selecting a coupling type for medium- to high-displacement helical piles. Each type of coupling has advantages and disadvantages and must be analyzed on the bases of efficiency, capacity, installation, and economics of a project. Typical couplings that are chosen by designers include square on square, flange to flange, external pipe sleeve, internal pipe sleeve, and welded joint. A helical pile must transfer axial, lateral, bending moment, and torsional loads, and the coupling must be designed to effectively and efficiently transfer each type of load. During the installation of a helical pile, the rate of penetration and the disturbance of soil layers play a critical role in the efficiency and torque to capacity ratio (Kt) of the pile. It is common for a coupling to protrude beyond the outside diameter of the pipe section being used. This is necessary for the function of certain coupling types and can facilitate the connection of couplings. However, it causes increased soil disturbance and reduce the rate of penetration due to soil bearing against the protruding portion of the coupling. A helical pile designer typically will work to minimize the coupling protrusion and create a pile with optimal installation efficiency but may choose a design with lower installation efficiency if it offers sufficient economic advantage.

Jan 1, 2019

By D. E. Healy

In 1989, an autogenous grinding task force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding (SAG) at the National Steel Pellet Plant in Keewatin, MN. Pilot plant test work, performed by the Hanna Research Center (HRC), indicated that fully autogenous grinding with pebble extraction and crushing could be incorporated into the existing circuits. In 1990, one of the existing 10 grinding mills was converted for an in-plant test incorporating pebble crushing. Full-scale test work were conducted in 1990 and 1991. They verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit using pebble crushing being greater than throughput of the existing SAG mill circuits. The plant produces 5 Mt/a (4.9 million ltpy) of iron ore pellets from 17.6 Mt (17.3 million It) of crude taconite. Crude ore is single-stage crushed by gyratory crushers. Primary grinding is performed by 10 semi-autogenous wet grinding mills. Secondary grinding is performed by five ball mills. Induration is with an Allis Chalmers grate-kiln pelletizing system. The primary grinding circuit consists of 108.2-m-diam x 5.5-m long (27 ft-diam x 18-ft) SAG mills. The mills are charged with 127 mm-diam (5 in.diam) steel grinding balls at from 3% to 5% by volume. Ball consumption rate is about 0.55 kg/t (1.25 lbs/lt) of crude ore feed to the mill. Each SAG mill is powered by two 2.6 MW (3500 hp) motors drawing 5450 kW (7300 hp) at 76% of critical speed. The mills are grate discharge with 16 mm (0.6 in.) slotted grate openings when new. The mill discharge is sized on a trommel screen having 4.5 mm (0.2 in.) openings. The plus 4.5 mm (+0.2 in.) oversize material is returned to the discharge end of the mill by a reverse screw auger located in the center of the trommel. The -4.5 mm (-0.2 in.) trommel screen undersize is pumped to magnetic cobbers.

Jan 1, 1992

By Michael S. Miller

In 1985, at the request of the Bureau of Land Management, the Bureau of Mines studied a 50,57U-acre portion of the 90,345-acre Twin Peaks Wilderness Study Area (CA-020-619A) in order to evaluate its identified resources. The area studied is located about 45 miles northeast of Susanville, CA, in Lassen County, CA, and Washoe County, NV. The area is underlain by Tertiary volcanic, volcaniclastic, and intrusive rocks. Quaternary stream, lake, and landslide deposits overlie the older rock. There are no mines or mining claims in the study area. One mineral resource, pozzolan, was identified. Mining claims, inactive in 1985, have been staked adjacent to or near the northwest corner of, and also southeast of, the study area. Examination and sampling of 17 mineralized sites, delineated mostly by prior geochemical surveys, showed at least 30 million tons of subeconomic pozzolan resources and small or low-grade occurrences of gold, silver, copper, lead, zinc, nickel, molybdenum, zeolites and clay.

Jan 1, 1986

By E. W. Parsons

Permanent support of the back is an important economic factor in maintaining a tunnel or other underground opening in condition to render the service for which it was driven. Timber has been most commonly used for support in tunneling and drifting because of its strength and ease of installation. Even when treated for decay, however, timber is subject to deterioration and, over a long period of time, should not be considered a permanent support. Concrete support or lining is permanent and has been used in tunnels of every size for many years but has been almost exclusively cast in place, a difficult, costly process. This report deals with the design and installation of precast concrete supports to combine the best features of both methods.

Jan 1, 1958

By G. K. Derby

The Bureau of Mines investigated methods for removing dragline bucket wire rope terminations with the objective of finding efficient methods that are safer than the method most commonly used at U.S. surface mines, which is to use the explosive impact of a projectile fired from a cannon to remove the rope termination. Removal of a wire rope termination for repair or replacement requires separation of the wedge and socket that lock together to secure the rope end. The Bureau investigated currently used methods and improved upon and tested two safer alternate methods for removing wire rope terminations. A cannon test program was conducted, using 40-and 50-gr primer (detonating) cord, to establish the possible force produced with a 4-in-bore cannon and a 55-lb projectile. Wedge and socket units supplied from cooperating mines were separated under controlled conditions to establish data on separation force requirements. The two alternate methods investigated were use of the force generated by (1) a pendulum ram and by (2) a portable hydraulic pusher. Both methods are capable of providing sufficient force to effect wedge and socket separations on draglines with up to 78-yd3 buckets under normal conditions.

Jan 1, 1984

By M Wieloch, D Wimpenny, M Chappell

Fibre-reinforced geopolymer concrete (FRGC) contains no Portland cement or steel reinforcement, but instead uses synthetic fibre reinforcement and a geopolymer binder. The use of geopolymer binder in lieu of Portland cement reduces the concrete’s embedded energy (CO2 emissions) whilst the use of synthetic fibres eliminates the issue of reinforcement corrosion, thus enhancing the overall long-term durability of concrete. This paper presents the development of FRGC during a three-year project funded by the Victorian Science Agenda and a consortium of five organisations. The work involved laboratory and field trials and the production of prototype tunnel segments that have been subject to durability and fire testing.FRGC has exceeded the performance of the Portland cement-based control mix in terms of flexural strength, chloride diffusion, water sorptivity and drying shrinkage. Furthermore, the FRGC segments subjected to a simulated hydrocarbon fire test did not exhibit explosive spalling; however, the creep of FRGC was approximately three times that of the steel fibre-reinforced Portland cement-based control mix. The compressive strength and tensile splitting strength of the FRGC were also lower than the control mix. These differences need to be allowed for in the design using FRGC.Prototype bolted tunnel segments of up to 0.8?t mass have been produced from FRGC using standard production techniques and ambient curing. These were successfully produced within a 24-hour production cycle. Cut sections through the segments showed good compaction and even distribution of fibres. The estimated carbon footprint of tunnel segments produced using FRGC is approximately 70 per cent less than that of Portland cement-based segments containing 25 per cent fly ash and steel reinforcement.The results to date indicate that FRGC has the potential to produce a new generation of tunnel segments and, in general, precast concrete products with increased durability and substantially reduced carbon emissions compared to the Portland cement-based concrete with steel reinforcement.A summary of further research carried out by CH2M HILL into a complete elimination of ferrous inserts from segmental concrete tunnel lining is also summarised in this paper. The use of non-ferrous connectors for radial joints in combination with the FRGC technology in the manufacture of tunnel segments will effectively lead to development of a new generation of segmental tunnel lining systems.CITATION:Wimpenny, D, Chappell, M and Wieloch, M, 2014. Fibre-reinforced geopolymer concrete – an innovative material for tunnel segments, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J P. Sykes, T C. McCuaig, M Jessell, A Trench

The election of Donald Trump and the Brexit referendum herald a shift towards a tighter definition of economic value, at the expense of the broader value concept of sustainable development; as well as a rise of protectionism, reversing a long-term trend of globalisation. However, the situation is complex, especially over the longer term in which mine project development and exploration operates. The minerals sector should proceed with caution. A greater focus on the local impacts of mining may be strategically beneficial, not only to mitigate against a potential protectionist future, but also because sustainable development has become more ‘localist’ via the concept of ‘social licence to operate’, whilst globalisation also seems to provoke increased ‘localist’ sentiments (known as ‘glocalism’). Localist strategies, therefore, seem a good hedge against multiple political futures. By contrast, moving away from sustainable development appears strategically riskier. Not only are ‘unsustainable’ activities, such as pollution and civil rights infringements harder to reverse, but a movement towards a more sustainable global economy may already be predetermined, even if the journey there may seem oblique. It appears that the increased economic development that is coveted globally is intrinsically linked to a rise in environmental and social consciousness.CITATION:Sykes, J P, Trench, A, McCuaig, T C and Jessell, M, 2017. Charles Dickens on the (potentially) changing role of globalisation and sustainability in the long-term future of mining and exploration, in Proceedings Tenth International Mining Geology Conference 2017, pp 239–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Isabel F. Barton, Matthew J. Gabriel, CARSON ROBERTS, JOHN LYONS-BARAL, LEON DUPLESSIS, Mark D. Barton

Geometallurgical characterization is increasingly used in the mining industry to model ore types, predict process performance and identify potential recovery issues ahead of time. However, most geometallurgical assessments are based on bench- or laboratory-scale analyses of relatively sparse samples, leaving most of the orebody characteristics known only by inference until the rocks are actually mined. In this pilot study, we test drone- and tripod-based hyperspectral imaging for mapping mineralogy across mine highwalls, dumps and leach pads. The results show that hyperspectral imaging can successfully map the types and distribution patterns of key minerals (especially carbonates, sulfates, clays, other phyllosilicates) and other important features (such as lixiviant ponding on leach pads), bringing geometallurgy into the field to provide crucial inputs to process decisions.

By John G. Kuhm

INTRODUCTION The goal of any development drilling program is the drilling of the exact number of holes necessary to adequately determine grade and dimensions of an orebody, no more and no less. This cost of development drilling represents a large part of the total development budget. Any technique which eliminates unnecessary drilling costs produces beneficial results, both to the company and to the person who can claim the savings. This high development cost factor has produced a quantity of research to develop techniques, for efficient control of drilling programs. Recent mining literature is full of articles describing methods for measuring and increasing the effectiveness of these expensive projects. The method described in this paper was developed during the latter part of a major development drilling project at the Christmas Mine of Inspiration Consolidated Copper Company in Gila County, Arizona. It was used to test the need for drilling individual holes but could be expanded to control an entire project. This technique was used at Christmas as a practical means for evaluating adequacy of drilling on an individual hole basis, and it was possible to eliminate several previously approved holes. Application of this method involves an evaluation of geological conditions present and a good bit of common sense. Projects involving large disseminated, rather homogeneous orebodies of the porphyry-copper type would be the most likely candidate for application of the technique. Discontinuous orebodies would not be amenable to this technique. The method is based on the measurement of the linear correlation between the spatial distribution of two sets of data. The Pearson product-moment correlation coefficient is used. This is a standard statistic commonly used to measure linear correlation between two sets of data. The statistical significance of the correlation coefficient at a 95% confidence level is the main criterion for controlling the project. For purposes of reference we will call our technique the "correlation method" in this paper.

Jan 1, 1971

By Marc Arpin

La Bolivie possède tout pour réussir. Son vaste territoire de plus d'un million de km2 et qui occupe une position stratégique au coeur du continent sud-américain recèle des ressources naturelles (forêts, minéraux, gaz naturel, etc) variées et abondantes. Elle a une frontière avec pas moins de 5 pays dont le géant que constitue le Brésil ainsi qu'avec l'Argentine, l'autre puissance régionale. Pourtant, malgré tous ces atouts, la Bolivie demeure l'un des pays les plus pauvres du continent. Ce paradoxe n'est nulle part mieux reflété que dans le secteur minier. Celui-ci fait face à une situation de crise en dépit d'une tradition minière de plus de quatre siècles et d'un potentiel géologique indiscutable ayant conduit à la découverte et à l'exploitation de fabuleux gisements d'argent et d'étain. Les habitants des districts miniers vivent dans des conditions de pauvreté extrême et les indicateurs de développement humain de ces régions sont parmi les plus bas en Amérique du Sud. La Bolivie réussit difficilement à attirer les compagnies minières alors que, chez les voisins, et particulièrement en Argentine, qui n'a pas de tradition minière, les investissements miniers majeurs affluent. Dans cette conférence, nous chercherons à expliquer les causes de cette situation et proposerons des solutions possibles.

May 1, 2001

By Venkata Krishnaiah Yeddala, Sai Vivek Adari, Suresh Kumar Velugu

Assam cancer care foundation (ACCF) proposed the construction of hospitals and related facilities across 18 locations in the state of Assam-India. Tezpur is one among the 18 locations of Assam with high seismic risk. The strata at the site are comprised of mostly fine silty sands of lower SPT- N values. The water table is also encountered and ranging from 1 m to 2 m below EGL. Since the site lies in seismic zone V as per IS 1893, detailed liquefaction analysis is carried out for all five boreholes and indicates that soil is liquefiable and ground improvement is inevitable up to a depth of 15 m below existing ground level. To mitigate the liquefaction potential and enhance the seismic performance of the soil, ground improvement using stone columns by Wet top feed Vibro-replacement method is proposed. Also, the differential settlements can be avoided effectively under the raft foundation with Vibro Stone Columns. In this paper, field test validation results such as Pre and post-SPTs and ECPTs to access the extent of ground improvement, along with other information adopted in this project presented.

Nov 1, 2022

By Eirik Sundvor, Hany Doss, Peter Vogt, Kathleen Crane

"Abstract - In 1989-1990, the SeaMARC II side-looking sonar (11 to 12 kHz) and swath bathymetric system imaged more than 80 000 km2 of the seafloor in the Norwegian-Greenland Sea and southern Arctic Ocean. One of our main goals was to investigate the highly oblique (115°) junction between the Mohns and Knipovich ridges, and to determine, using new morphotectonic data, whether or not this junction is stable or in a state of readjustment. These findings are presented in this paper.Along the northern Mohns Ridge, we observed a highly segmented rift valley undisturbed by transform faults. In contrast to the elevated Reykjanes Ridge, the Mohns Ridge is dominated by deep en echelon fault-bounded troughs, which are bordered by high rift valley volcanoes. These segment boundaries are interpreted to be sites of recent to present volcanic activity, based on their high acoustic reflectivity. The northwestern flank of the Mohns Ridge is marked by shallow quasi-linear ridges parallel to the present orientation of the Mohns Ridge. The orientation and geographic position of these ridges suggest that they were formed at the Mohns Ridge. Only in the northernmost cases are some of these off-axial ridges non-linear. The degree of the non-linearities increases slightly with proximity to the Mohns-Knipovich bend. In addition, because no transform fault was detected between the Mohns and Knipovich ridges, we conclude that the Knipovich Ridge must be obliquely spreading to the NW-SE."

Jan 1, 1999

By L. J. Buter, D. J. Collins

Introduction FMC's Paradise Peak gold mine was discovered by staff geologists in July 1983. Located south of Gabbs, in western Nevada, the deposit contains about 11 Mt (12 million st) of ore grading at 3.6 g/t (0.105 oz per st) of gold and 129 g/t (3.75 oz per st) silver. It is estimated that the ore contains 34 t (1.1 million oz) of recoverable gold and 933 t (30 million oz) of recoverable silver. The 3.6 kt/d (4000 stpd) mill began operation April 14, 1986, just 18 months after Davy McKee completed a feasibility study and construction, and two-and-a-months ahead of schedule. It also came in about 10% under budget at a cost of about $100 million. Crushing Run-of-mine ore is delivered from the mine in 45-t (50-st) haul trucks to a 272-kt (300,000-st) capacity open air stockpile. Ore is reclaimed using 5 m3 (7 cu yd) front-end loaders that feed a 91-t (100-st) hopper equipped with a 610- x 610-mm (24- x 24-in.) grizzly. A 1.4- x 11-m (54-in. x 35-ft) apron feeder delivers ore from the hopper by way of a vibrating grizzly screen with 127 mm (5 in.) openings to a 1- x 1.3-m (43- x 51-in.) Rexnord jaw crusher. Crushed material is conveyed to a 1.8- x 4-m (6- x 14-ft) Link Belt vibrating screen equipped with a 50-mm (2-in.) manganese grizzly bar deck. Screen oversize is fed to a 1.7/0.6-m (5.5 ft) Rexnord standard cone crusher. Product from this crusher joins the -50 mm (-2 in.) screen undersize and is conveyed to a 136-t (150-st) surge bin. Three hydraulically driven belt feeders deliver ore from the ore bin to three 2 x 6 m (7 x 20 ft) Link Belt single-deck tertiary screens fitted with 6 x 25 mm (0.25 x 1 in.) slotted polyethylene screens. Screen undersize - -6 mm (-0.25 in.) rock - is conveyed to a 3.6-kt (4000-st) ore storage bin. Screen oversize is delivered by way of a conveyor to a 91-t (100-st) surge bin. From this bin, two belt feeders feed ore to two 1.7 m (66 in.) Rexnord Gyradisc crushers, which are in closed circuit with the tertiary screens. Design features include magnetic protection for tramp iron removal and sloping floors and pump sumps for ease of clean up. Dust scrubbers keep the working environment clean and in compliance with state dust emission regulations. Grinding Two 1 x 4.5 m (3.5 x 15 ft) belt feeders deliver ore from the fine ore bin to a conveyor belt that feeds it to the 5 x 7 m (16 x 22 ft) Allis-Chalmers ball mill. The conveyor belt is equipped with a Merrick weightometer. This controls feed rate to the ball mill by speed control on the hydraulic motors driving the feeders. The 2.6 MW (3500 hp) powered mill grinds 3.6 kt/a (4000 stpd) to an average grind of 85% -75 µm (-200 mesh). The mill is in closed circuit with four 660 mm (26 in.) Krebs cyclones. Three of these are normally in operation while one is a standby. Warman pumps feed the cyclones through a cyclone distribution manifold. The cyclone underflow returns to the ball mill, which has a 300% average circulating load. Mill discharge pH is 11, and that is obtained through pebble lime addition to the feed belt. Cyclone overflow is sampled using a Heath & Sherwood two-stage sampler. It then flows to a 27-m-diam (90-ft-diam) Eimco thickener. Thickener overflow is returned to the grinding circuit, while underflow at 50% solids is pumped to the leaching circuit. Grinding-circuit design features include a steeply sloped floor for ease of clean up, an open area over the pumps for maintenance accessibility, and a ball hopper with a self discharge bottom to speed ball addition. Other features include a mill liner handler and an air clutch that connects the mill motor to the mill.

Jan 12, 1986

By J. Douglas Causey

In 1986 and 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied 73,010 acres of the 76,480-acre Lower Owyhee Canyon Wilderness Study Area (OR-003-110) in order to evaluate its identified mineral resources. The study area is in Malheur County, OR, about 8 miles north of Rome. There are approximately 7.7 million tons of subeconomic zeolite (heulandite and/or clinoptilolite) resources with ammonia ion exchange capacities as high as 1.75 milliequivalents per gram in the Chalk Basin-Lambert Rocks area. The bed is 25 ft thick with less than 100 feet of overburden. This resource probably will not be mined in the foreseeable future.

Jan 1, 1989

By F Ouchterlony

Soviet precursors to Cunningham’s Kuz-Ram model from 1983 are described. They are rooted in the mean fragment size and Rosin-Rammler (RR) fits to sieving data and rely on approximations. Three versions of the Kuz-Ram model are presented and all three are de facto based on the median fragment size x50, even if the term mean is used in the papers. This discrepancy caused Spathis in 2004 to suggest a correction procedure for the Kuz-Ram rock factor A, which was said to explain some of the missing fines in the model. This correction, while applicable to Cunningham’s 1983 paper, does not apply to his 1987 paper, in which he presents his own A factor.Common fixes of the Kuz-Ram model’s fines issue are fragmentation models where the fines are mainly generated in a crushed zone around a blasthole. This is contradicted by careful model blasting tests. The lack of a largest block size in the RR function may lead to spurious values of the uniformity coefficient n, eg in conjunction with image-based fragmentation measurements or crusher modelling. These issues may be solved by using the transformed RR function, which has a largest block size xmax or its replacement by the Swebrec function, such as in the KCO model.The mean to median issue is investigated in some detail and it is found that using x50 instead of the mean:has a sounder theoretical backgroundis less prone to errorsis not contradicted by the original Soviet data.It is finally suggested that future work on fragmentation prediction equations focus on the use of distribution independent quantities like percentiles, eg x50, x20 and x80. Some previous work in this direction is briefly analysed and one consequence is that the n-value of the Kuz-Ram model should depend on specific charge.CITATION:Ouchterlony, F, 2015. The median versus the mean fragment size and other issues with the Kuz-Ram model, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 109–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J. Bootle

Marrow vein deposits will continue to be an important source of valuable minerals. Productivity per manshift is not keeping pace with operating costs. Increased mechanization of stoping operations must be obtained to create greater productivity at a reduced cost per ton. This application of mechanization may be to either present methods or to newly developed concepts. The total mine unit operations will be effected by increased productivity. Two approaches to increasing the mechanization of narrow vein stoping were studied with the intention of increasing stope productivity and decreasing stoping costs. A method of bringing efficient rubber-tired equipment into narrow cut and fill stopes was designed. It proposes to provide stope access by way of a ramp constructed on the stope fill. Impact breaking equipment was studied and specific applications proposed.

Jan 1, 1977