Search Documents

By Robert W. Ageton

The Bureau of Mines investigated the in situ vertical component of the rock stress in the rib of the haulage drift on the 6100-level of the Star mine, Burke, Idaho, using the flatjack and borehole deformation methods. The estimate of the vertical component of stress about 2 feet into the rib at a station along the haulage drift on the 6100-level of the Star mine by the flatjack method is approximately 5,875 psi, whereas the borehole deformation procedure at this station yielded a value of 5,500 psi for the same depth into the rib. The test zone is approximately 5,625 feet below the surface.No attempt was made to extrapolate stress estimates beyond the depth of the flatjack installation.

Jan 1, 1967

By D. KEYS, D. E. Gemmell

The portion of the earth's surface covered by peatlands has been conservatively estimated at over 420 million ha (Kivinen and Pakarinen 1980). It is estimated that there are about 170 million ha of peatland in Canada. New Brunswick contains about 140,000 ha. Harvesting of peat for horticultural purposes has been carried out in New Brunsiwck since 1942. This industry, and the potential for using peat for energy purposes, indicated the need for an accurate assessment of the resource. In 1975, therefore, the New Brunswick Department of Natural Resources began a detailed peatland inventory. Assistance from the Canada Department of Regional Economic Expansion permitted acceleration of this program and field work was completed in 1982. Information gathered by the program will form the basis for a management plan for future use of the resource.

Jan 1, 1984

By Carl W. Kelley

PRODUCTION in the United States of carbon black has increased from 20 million pounds per year in 1920 to over 2 billion pounds in 1964 valued at $156 million, mostly for consumption by the rubber-tire industry, which uses over 90 percent of total production. Production of over 2 billion pounds in 1964 is a 7.8-percent increase over 1963 and is the first time furnace black production has topped 2 billion pounds. Although 1964 channel black production dropped 6 percent below 1963, carbon black produced by the furnace process, which ac-counted for 92 percent of total production, increased 9 percent to 2,053 million pounds. Total shipments during 1964 amounted to 2,245 mil-lion pounds, a 7 percent increase. This growth parallels the expansion of the automotive and petroleum industries. Along with this expansion have been many advances, both in methods of manufacture and in the quality and variety of blacks available to industry. There are several kinds of carbon black, thermal, channel, furnace, lamp, and oil blacks. Until recently, channel has been the important black in rubber compounding. Following the introduction of the synthetic GR-S, and more recently of "cold rubber," it has been found that certain furnace blacks with particle size larger than that of the standard channel black give superior reinforcement. A great advantage of furnace black is that its yield per unit of gas feedstock is higher than that of channel black. The 184-million-pound increase in domestic carbon black sales was partially offset by a 37-million-pound decrease in exports. Decrease in exports especially to Europe, is expected to continue. In Europe, as in the United States, the major end use for carbon black is in the manufacture of automobile and truck tires. Although the number of automobiles in Europe is predicted to grow by about 7.5 percent per year, compounded until 1975, the increased demand will be met by a 20 percent increase in existing capacity and by the new plants being built in Europe by U.S. companies. Also) aromatic oils for producing furnace blacks are plentiful now that western Europe's chemical industry is switching to a petroleum base.

Jan 1, 1965

By Adrian Dance

Barrick Gold Corporation?s wholly owned subsidiary, Barrick (Granny Smith) Pty. Ltd. operates the Granny Smith operation in Western Australia and has been operating a SAG/ball mill (SABC) circuit for a number of years processing a blend of secondary crushed, open pit and underground material. With closure of the open pit in 2008, Granny Smith was considering different options to process underground only material at a lower throughput. Using the existing equipment available on site, a number of circuits were evaluated by Metso Process Technology & Innovation (PTI) through modelling and simulation. A single stage SAG mill circuit was selected based on power requirements and operating efficiency. In April 2008, Granny Smith started operating their SAG mill in single stage, processing primary crushed feed and using their existing pebble crusher for scats. Smaller cyclones were used to control the final grind size. PTI surveyed the new single stage circuit in July 2008 under normal and high rock load conditions to show the effect on final grind size. Granny Smith continued to operate this circuit until the end of 2009, when alternate feed sources resulted in a return to the complete SABC circuit at a higher tonnage once again. The variable speed, single stage SAG mill proved itself to be very efficient and flexible option to process the hard underground Wallaby Deeps material. This paper will review circuit performance following the conversion to single stage in comparison with the full SABC circuit.

Jan 1, 2012

By V. Maseko, C. Musingwini

"When considered collectively, Mineral Resources and Mineral Reserves are arguably a key asset for any mining company. Mineral Reserves are the economically mineable portions of Mineral Resources. They therefore provide a good indication of the economic prospects in the short to medium term and associated non-financial impairments for mining companies, hence a focus on Mineral Reserves. An assessment of modifying factors for converting Mineral Resources to Mineral Reserves revealed that Mineral Reserves were most sensitive to long-term commodity prices, hence the focus on long-term commodity prices. The justification for selecting gold and platinum mines is that they collectively make a significant contribution to South Africa’s earnings from mining.The introduction of the South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code) in 2000 informed the basis for analysing long-term commodity price assumptions for major South African gold and platinum mining companies between 2000 and 2016. The analysis revealed that the least number of non-financial impairments occurred when long-term commodity prices were within ±5% of spot prices. This finding suggests that this range is the ideal range for long-term commodity price assumptions to improve confidence in Mineral Reserve declarations and minimize impairments. Introduction The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code) defines a Mineral Resource as ‘a concentration or occurrence of solid material of economic interest in or on the Earth’s crust in such form, grade or quality and quantity that there are reasonable prospects for eventual economic extraction’ (SAMREC, 2016, p. 18). Mineral Resources are categorized according to increasing levels of geoscientific confidence or knowledge, from Inferred to Indicated and lastly, Measured categories. The SAMREC Code defines a Mineral Reserve as ‘the economically mineable part of a Measured and/or Indicated Mineral Resource’ (SAMREC, 2016, p. 25). In some of the other reporting codes such as the Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the JORC Code), a Mineral Reserve is synonymous with an Ore Reserve. The conversion of Mineral Resources to Mineral Reserves involves applying modifying factors, which are non-resource considerations. The modifying factors used in the Mineral Reserve estimation process include mining, metallurgical, processing, infrastructure, economic, marketing, legal, environmental, social, and governmental factors. Each of these modifying factors consists of several components which require due consideration in the estimation of Mineral Reserves. Table I shows some of the components typically considered for each of the modifying factors."

Mar 1, 2019

By Edward E. Tate

This is a report on the design, development, and manufacture of a prototype roof bolting machine for high rise applications. The machine is designed to traverse a 32 inch entry and rebolt a roof fall area to a height of 28 feet 10 inches. Covered in the report is a chronology of the project, an explanation of the design problems, and a description of their solutions. The report concludes that the equipment as designed is suitable for the purpose intended and further testing is recommended.

Jan 1, 1981

By P. Mundell, R. Torbin

"There are many physical and operational obstacles in pipelines that make the passage of inspection robots impossible including:•,Small radius bends•,Low operating pressure•,Plug valves•,Large changes in pipe size•,No permanent access to the pipeline.The inspection of unpiggable pipelines requires the marriage of a highly agile robotic platform with NDE sensor technology operating as an integrated system. Foster-Miller and GE/PII are developing a robot that is essentially a battery powered, train-like platform. Both front and rear tractors propel the train in either the downstream or upstream direction. Like a train, the platform includes additional ""cars"" to carry the required payloads. The cars are used for various purposes including the NDE sensor module(s), the power supply, and data acquisition/storage components. The robot is designed with a slender aspect ratio and the ability to change shape as required by the physical obstacle presenting itself. The MFL sensor module must also morph itself through the physical obstacles, and thus, will require some level of segmentation. The segmented MFL magnetizers and transformable sensor module represent a major advance in the science of sensor technology and pipeline inspection."

Jan 1, 2005

By C. Butcher

Numerical simulations of straight tube hydroforming of a dual phase steel were performed using both upper and lower bound constitutive models for porous ductile materials. The Gurson model is based upon an upper bound approximation to the material behavior and thus overestimates formability. Conversely, a lower bound solution to Gurson's unit cell geometry was developed by Sun and Wang to provide a conservative estimate of formability. The effect of a compressive axial load (end-feed) on damage development and tube formability is investigated. The resulting upper and lower bound models successfully captured the experimentally determined burst pressure, formability and failure location.

Jan 1, 2010

By G. W. Reimers

Conditions in the underground mine environment can cause self-heating of sulfide ores as a result of exothermic oxidation reactions, which may result in mine fires. This Bureau of Mines report describes thermal analyses of finely ground chalcopyrite, chalcocite, galena, pyrrhotite, marcasite, and arsenopyrite, to characterize their responses under oxidizing conditions. Thermal gravimetric analysis (TGA) and differential thermal analysis (DTA) were used, in the temperature range 1000 to 5000 C. Chalcopyrite showed an initial weight gain, due to formation of sul-fates, a weight loss, caused by ignition of iron sulfide to iron oxide, and a final weight gain, indicating the conversion of copper sulfide to sulfate. Chalcocite did not ignite in the temperature range studied but exhibited a rapid weight gain, because of the rapid conversion of copper sulfide to sulfate. Likewise, galena failed to ignite but underwent a steady weight gain when oxidized in a moist atmosphere, showing conver-sion of lead sulfide to sulfate below the ignition point. Marcasite underwent a rapid weight loss, indicating ignition, at 2000 C. Moisture in the oxidizing atmosphere lowered the ignition point of marcasite and arsenopyrite but not that of pyrrhotite. All the sulfides exhibited exothermic behavior at temperatures below the ignition point.

Jan 1, 1987

By Bai-ru Xia, Cang-qin Jia, Qi-wu Huang

Limit Analysis Theorems has revealed to be a powerful tool for the development of numerical models aiming the determination of the load bearing capacity of structures reached by plastic collapse. This work presents a numerical formulation for the computation of strict upper bounds of the collapse loads of rigid-perfectly plastic mechanical systems, derived within the kinematical theorem framework. A key advance of this present method is that the problem is described only in terms of nodes and discontinuities connecting those nodes rather than element or bodies. The alternative approximation procedure to the traditional finite element method might involve discretization of a given body using a suitably large number of nodes laid out on a grid, with the failure mechanism comprising the most critical subset of potential discontinuities interconnecting these nodes. Potential discontinuities which interlink nodes laid out across the problem domain are permitted to crossover one another, giving a much wider search space than when such discontinuities are located only at the edges of finite elements of fixed topology. Highly efficient interior point method solvers can be employed when certain popular failure criteria are specified (e.g. Mohr-Coulomb). By adopting this processing approach it is possible to solve very large problems which normally exceed the memory capacities of a single computer. The developed numerical tool reveals to be robust and versatile, able to solve a wide range of 2D problems. Velocity singularities are automatically identified and visual interpretation of the output is straightforward. Several numerical examples including rock slope are studied by the new method, and the results are very close to those calculated by using analytical method and FEM.

Jan 1, 2015

By CH. Liu, H. X. Jiang, X. Xiao

"A study has been conducted to characterize the fatigue life in 7050-T7451 thick plate by the comparison between an experimental alloy and commercial alloy. The fracture origins were specified and their sizes were measured by scanning electron microscope (SEM). Additionally, the size, number density and spatial distribution of porosity in the experimental material and commercial material were characterized and compared, using X-ray Computed Tomography(XCT). The results showed that microporosity was the predominant site for crack nucleation and subsequent failure of the experimental alloy. However, as for the commercial alloy, fatigue cracks were found to originate from constituent particles. The presence of microporosity in 7050-T7451 thick plate reduced fatigue life of an order of magnitude or more compared to the commercial alloy. The relationships between size of origin and fatigue life were proposed. It was showed that the fatigue endurance was reduced when the size of porosity increased.INTRODUCTION 7xxx series aluminum alloys, due to their combination of high strength, high resistance to stress corrosion cracking, and good fracture toughness, are widely used in structural engineering applications where high-strength and low-density characteristics are fundamental design requirements (Williams& Starke, 2003). Every designer is striving to find an optimal combination of properties including strength, corrosion resistance and fatigue resistance (Wanget al., 2016). Based on the design principles of aircraft, a higher fatigue resistance of aluminum alloys are required. Thus, many investigations have been carried out on the microstructures and its effect on fatigue properties of the 7xxx series aluminum alloy (Robson, 2004; Schubbe, 2009).Microporosity, which is a common defect in casting materials, can lead to a significant deterioration of mechanical performance and fatigue resistance, especially in the high alloyed 7xxx aluminum alloys. The actual valid loading area decreases due to microporosity, which results in detrimental effect on the mechanical properties. Many experimental studies have been conducted in this research field. Mayer et al.(2003) investigated the fatigue properties of magnesium alloys produced by high-pressure die-casting. The results show that porosity in magnesium alloys greater than0.18mm diameter may be considered as the most important material defect for high cycle fatigue and fully reversed loading conditions. Nadot et al.(2004) found that the near surface defects are much more dangerous than the internal defects. Wang et al.(2001a) used the Weibull statistics method to analysis the influence of the microporosity, oxides and particles on the A356-T6 alloy fatigue life. The results show that, the porosity is more detrimental to fatigue life than oxide films and particles. With regard to fatigue resistance, although the deleterious effect of microporosity has been generally acknowledged, a quantitative understanding between casting microporosity and fatigue life in 7050-T7451 plate is not well established."

Jan 1, 2018

By Thomas Domanski

Any type of deep excavation whether for Bored Piling, Diaphragm Walls or Contiguous Bored Piling Walls depends on forming a stable borehole with a defined cross-section to receive safely the permanent materials. In modern construction the excavation depth can reach well the range of 100 m and above. The diameters of the Piles reach often sizes of 2.5 m and bigger. Top casings in Bored Piles (Diaphragm Wall none) are rather short and stability below the casing, need to be secured by stabilization slurry. The boreholes need to be formed through a variety of different materials and stand open for an extended period. Without a safe stable borehole, it is impossible to produce quality products and work cost-efficient. The understanding and proper usage of a suitable slurry is a key element essential for the delivery of Foundation Elements with high quality and within a reasonable budget. The setting of mechanical and rheological parameters in specifications is necessary and helpful, but probably insufficient to embrace and control such a key element in the practical implementation of foundation construction. The proper selection, design, implementation and supervision of slurries on site requires both from Contractors and Engineers to understand how different slurries do function. Only with this knowledge the right decisions in slurry operations can be made. This talk is directed to give some help to both, Contractor’s and Engineer’s, in understanding how different type of slurries do work. (Which ones should be preferred in what kind of soils.) The better knowledge will help the Contractor to control cost and enhance production. The Engineer will be able to assist in arriving at the appropriate technical choices and include in the specifications.

Sep 1, 2022

By J. M. Wempen

As development in underground coal mines progresses away from the critical components of the ventilation system, including the main fans and ventilation shafts, resistance within the system is markedly increased. This results in higher pressure and flow requirements from the main fan(s) to maintain adequate face ventilation. Upgrades to the primary ventilation system are often required. The use of booster fans underground is a potentially practical alternative to the addition of shafts and surface fans. This study presents simulations of the use of booster fans in two underground ventilation scenarios, one longwall and one room-and-pillar. The booster fan effects on the power requirements of the ventilation systems are evaluated.

Jan 1, 2011

By A. Nieto

This article is a review of previous discussions about underground mining method selection and classification with the purpose to clearly define and classify the two groups of variables (indicators) involved in the mining selection process: key deposit indicators (KDIs) and key mining method indicators (KMIs). This paper provides a simple and clear approach for the classification and selection of a feasible underground mining method based on a predetermined set of favorable deposit characteristics, which are defined as key deposit indictors (KDIs). This article also gives a summary of the key advantages and disadvantages associated with every underground mining method based on their key mining indicators (KMIs). The selection method given in this paper is based on defining field KDIs and comparing them to the KDIs that are favorable to every considered mining method. By cross validating a matrix of favorable KDIs, the paper presents a simple approach to rank several underground mining methods using a scale from favorable to less favorable accordingly to the ore deposit characteristics (KDIs). KMIs are used to further complement KDI rankings by analyzing every method’s KMI performance based on the expected productivity of the mining operation being considered. To further assist the reader through the selection process, this paper gives basic sketches representing each of the primary underground mining methods discussed in this paper. Each method is given using the same 3D isometric view as spatial reference to assist the reader with visual interpretation and comparison between methods.

Jan 1, 2010

By L. A. Morley

Volume III of the final report examines the indication versus interruption procedures used on motion-drive power equipment, with emphasis on surface excavators. The report begins with a review of the electromechanical acid conversion used with the Ward-Leonard control system. Protection criteria for the drive-system components are then discussed. Fault sources and fault calculations for both the ac supply source and dc power loop are introduced to assist in discussing indication and interruption procedures. The subject is then expanded to examine the dynamic process of the machine and determine the effects of fault current and position of the machine to allow for an orderly shutdown. With this analysis, possible indication an interruption procedures are given for the four-quadrant duty cycle of excavators. The report concludes by introducing other mining operations that utilize similar motion-drive systems and also static (solid-state) drives and recommends further research in these areas, as well as a more detailed examination of the dynamic fault analysis for excavators.

Jan 1, 1982

By R. L. Loofbourow

R. L. LOOFBOUROW 26.1-WATER FLOW, USE, EFFECTS, CONTROL Sec. 4 discusses ground water as a mineral resource. This section deals wits its control. 26.1.1-IMPORTANCE Flows of water have an important effect on the cost and progress of many deep excavations. The existence of water limits the methods which can be used in some and presents hazards in others. Lowering the water table may reduce the flow of springs and wells, with legal liability. Some mine water is used directly, some must he treated before discharge, and some contains dissolved solids which can be recovered profitably. Loss of life, property and production from flooding is grim, yet scores of mines have worked safely for generations under ground-water reservoirs, lakes and even the sea. The need for better control of mine water is measured by the severity of recent floodings, concern with the quality of the effluent, and direct and indirect costs of working wet ground. There are improvements in freezing in shaft sinking. pumps and their controls, treatment of mine water before it is pumped, bulkhead construction and certain efforts to reduce inflow. 26.1.2-PUMPING COST VS. COST OF WET WORK Direct operating and capital costs of pumping are more evident than indirect items, such as provision of extra standby power and maintenance facilities, The total of all these items is the cost of pumping water from an excavation. This is only a part of the extra cost of working wet as compared to dry ground. Less productive methods, less efficient equipment and more expensive explosives may have to he used in wet work. Wet rock plugs certain equipment. Maintenance is higher and labor less efficient. The cost of any means of keeping work drier should he weighed against the higher cost of working wet. The true difference in the cost of working wet ground, compared with dry, probably is known at only a few places (see checklist of cost items. Sec. 26.4.13). An extreme comparison of mining wet and dry ore is available from Ambrosia Lake, N.M. (Fig. 26-1). Between 1963 and 1967, a wet and a dry mine were worked by the same company under conditions otherwise comparable. Average operating cost at the wet mine, pumping 1,600 to 1,800 gpm. was $16.06 per ton of ore. The comparable figure for the dry mine was $7.50. Principal differences included the fact that the wet mine was worked from drainage levels below the, ore with rail haulage, the dry mine in the ore with off-track equipment loading and hauling to the shaft. In the wet mine, ore packed in chutes, cars and skips and froze in surface bins, stockpiles and trucks. Wet-mine costs included drilling drain holes, building and maintaining ditches and pumping water containing abrasive solids.

Jan 1, 1973

By S. K. Kawatra, S. J. Ripke, T. C. Eisele

It was determined by the authors that the water that remains in the filter cake after filtration in iron ore concentrators can contain several hundred times greater concentrations of calcium ions and other cations, due to surface chemical effects carrying the ions along with the water. Filter cake from two plants was analyzed. The water retained in samples of magnetite concentrate filter cake in Plant 1 contained 5088 ppm calcium and 5995 ppm magnesium, while the Plant 2 filter cake contained 231 ppm calcium and 119 ppm magnesium. These levels were dramatically elevated compared to the water that was removed from the concentrate by filtration for recycle to the plants (9 ppm calcium/15 ppm magnesium for Plant 1, and 11.9 ppm calcium/9.3 ppm magnesium in Plant 2). In addition to possible effects on agglomeration performance, the presence of these cations also affected the efficiency of filtration. In order to reduce the effects of these cations on filtration in Plant 2, carbon dioxide was injected into the slurry before it entered the filter press. This was found to increase filtration rates by up to 23.7%. Comparison of the results from the two plants shows that the concentrations of cations present in the filter cake will vary greatly from plant to plant, with correspondingly large variations in their effects on plant operations.

Jan 1, 2004

By Babak Mamaqani, Pirooz Barar

The Moanalua trestle spanned over Moanalua Stream, Honolulu, HI and was designed to accommodate construction of five 10 feet diameter cast in drilled hole (CIDH) piers as a part of Honolulu Authority for Rapid Transportation (HART) project. Due to the proximity of piers to the existing bridge, the trestle was elevated 20 feet above grade. Stratigraphy of the site consisted of shallow depth of fill and 150 feet of loose to very loose recent alluvium (soft clay) underlain with stiff to hard old alluvium (stiff clay). CIDH casings were installed by a rotator or oscillator depending on the diameter of the piers. The challenge was to design the trestle, not only for heavy gravity loads, but also to resist significant lateral loads from rotator and oscillator with minimal deflection. Series of piles, called reaction piles, were integrated into the trestle at each CIDH pier location to provide adequate lateral support for the rotator/oscillator. Due to the lack of information regarding soil Young’s modulus (E), a methodology was developed to calibrate and calculate E with two methods. Extensive analyses using LPILE and finite element analysis program, PLAXIS, were performed to model reaction piles and calculate lateral deflection. PROJECT SPECIFICATIONS The Honolulu Rail Transit includes 20-mile route and 21 stations to be built from East Kapolei to Ala Moana Center, with $1.55 billion construction budget. The project is divided into two phases as shown in Fig. 1: Phase 1 which connects East Kapolei to Aloha Stadium with expected operation in late 2020, and Phase 2 which connects Aloha Stadium to Ala Moana Center with expected operation in 2025.

Jan 1, 2019

By H. W. Kasaini, E. Bourricaudy, T. Larochelle

Rare Element Resources Inc., a U.S. based company, has developed a three-stage process for producing a +98% mixed REO powder from hard rock feedstock (-48 mesh, 2.9-4.8% REO) consisting of bastnaesite and ancylite minerals. Firstly, the whole ore is digested in chloride media at low temperature in counter-current flow mode. Secondly, the rare earths (REEs) are selectively precipitated as oxalates directly from an impure pregnant leach solution (PLS). Finally, significant amounts of free acid and water are recovered from the REE-depleted filtrate and subsequently recycled within the process. Excess heat from the oxalate calcination process is captured and reused in the plant. Due to the low leach temperature (45 ºC) and moderate acid dosage (240-297 kg/t, HCl), rare earth oxides (REOs) are preferentially leached out of fine solids leaving most of the base metals (Ba, Fe, and Al ) in the residue. Selective recovery of REEs from the PLS is achieved by mixing dilute oxalic acid (33% H2C2O4) and PLS at elevated temperature (85-95 ºC). The REEs plus thorium are precipitated as oxalates (REE2 (C2O4).xH2O) while the base metals are left behind in the barren filtrate. Multiple batch and pilot test results have confirmed that 50-80% of the oxalic acid can be recovered from the REE-depleted PLS through low-temperature crystallization (10-15 ºC). Typical leach efficiencies of critical rare earths at 45 ºC range from 85-99% (average 93%) while oxalate precipitation at high temperature increases the crystal size of RE oxalates (>450 microns, d80) thereby improving filtration. The economic benefits of this process include elimination of flotation and magnetic separation Capex and driving hydrometallurgical Opex down to $6- 7/kg, REO produced. As part of a comprehensive risk mitigation strategy, Rare Element Resources Inc has operated multiple pilot plants at SGS in Lakefield, Ontario, Canada to optimize counter-current leaching (CCL), REE oxalate precipitation (OXP), and thorium removal circuits. This paper presents pilot testing data from CCL and REE OXP circuits.

Jan 1, 2016

By Tristan Worsey, Brad Gyngell, Todd Buschjost, Gus Diehr

This paper highlights the opportunities provided by integrating MWD data and drone generated 3D model to industries that use explosive energy to perform useful work as an integral part of their rock extraction process.

Feb 1, 2020